235002325901L [YAGEO]
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 590ohm, 50V, 1% +/-Tol, 200ppm/Cel, Surface Mount, 0408, CHIP, LEAD FREE;型号: | 235002325901L |
厂家: | YAGEO CORPORATION |
描述: | Array/Network Resistor, Isolated, Metal Glaze/thick Film, 590ohm, 50V, 1% +/-Tol, 200ppm/Cel, Surface Mount, 0408, CHIP, LEAD FREE 电阻器 |
文件: | 总8页 (文件大小:283K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
ARRAY CHIP RESISTORS
YC124 (8Pin/4R; Pb Free)
5%, 1%
sizes 4 × 0402
Product specification
2
8
SERIES
124 (Pb Free)
YC
Chip Resistor Surface Mount
SCOPE
This specification describes YC124 series chip resistor arrays with lead-free terminations made by thick film
process.
ORDERING INFORMATION
Part number is identified by the series, size, tolerance, packing type, temperature coefficient, taping reel and
resistance value.
PHYCOMP ORDERING CODE
12NC CODE
CTC CODE
YC124 – X X X XX XXXX L
2350
(1)
XXX XXXXX L
( ) ( ) ( ) ( )
( )
5
( )
6
1
2
3
4
( )
(2)
(3)
4
PAPER / PE TAPE ON REEL (units) (2)
( )
1 TOLERANCE
TYPE/ START TOL. RESISTANCE
4×0402 IN (1)
(%) RANGE
10,000
40,000
033 13xxx
023 8xxxx
-
F = ±1%
J = ±5%
ARV341
ARV342 2350
Jumper
2350
±5% 10 to 1 MΩ
±1% 10 to 1 MΩ
033 11xxx
023 2xxxx
033 91001
( )
2 PACKAGING TYPE
2350
-
0 Ω
R = Paper/PE taping reel
( )
3 TEMPERATURE COEFFICIENT
OF RESISTANCE
(1) The resistors have a 12-digit
ordering code starting with
2350.
Last digit of 12NC
Resistance decade (3)
Last digit
– = Base on spec
X
0.01 to 0.0976
0
7
8
9
1
2
3
4
5
6
( )
4 TAPING REEL
(2) The subsequent 4 or 5 digits
indicate the resistor
X
0.1 to 0.976
07 = 7 inch dia. Reel
13 = 13 inch dia. Reel
X
1 to 9.76
tolerance and packaging.
X
10 to 97.6
100 to 976
1 to 9.76 k
(3) The remaining 4 or 3 digits
represent the resistance value
with the last digit indicating
the multiplier as shown in the
table of “Last digit of 12NC”.
( )
5 RESISTANCE VALUE
X
56R, 560R, 5K6, 56K, 1M
0R = Jumper
X
X
10 to 97.6 k
(6) RESISTOR TERMINATIONS
X
100 to 976 k
(4) “L” means lead-free
terminations.
X
1 to 9.76 M
L = Lead free terminations (pure Tin)
X
10 to 97.6 M
ORDERING EXAMPLE
X
Example: 0.02
=
=
=
=
=
0200 or 200
3007 or 307
1008 or 108
3303 or 333
1006 or 106
ORDERING EXAMPLE
The ordering code of an ARV341
convex chip resistor array, value
1,000 X with ±5% tolerance,
supplied in tape of 10,000 units
per reel is: 235003311102L.
X
0.3
The ordering code of a YC124
convex chip resistor array, value
1,000 X with ±5% tolerance,
supplied in 7-inch tape reel is:
X
1
X
33 k
X
10 M
YC124-JR-071KL.
NOTE
1. The “L” at the end of the code is only for ordering. On the reel label, the standard CTC or 12NC will be mentioned an additional stamp
“LFP”= lead free production.
2. Products with lead in terminations fulfil the same requirements as mentioned in this datasheet.
3. Products with lead in terminations will be phased out in the coming months (before July 1st, 2006)
www.yageo.com
Feb 04, 2005 V.1
Product specification
3
8
SERIES
124 (Pb Free)
YC
Chip Resistor Surface Mount
MARKING
YC124
E-24 series: 3 digits
2
YNSC029
First two digits for significant figure and 3rd digit for number of zeros
Fig. 1 Value = 240 KΩ
For marking codes, please see EIA-marking code rules in data sheet “Chip resistors marking”.
CONSTRUCTION
The resistors are constructed out of
a high-grade ceramic body. Internal
protective coat
metal electrodes are added at each
resistor layer
end and connected by a resistive
inner electrode
paste. The composition of the paste
end termination
is adjusted to give the approximate
ceramic substrate YNSC053
required resistance and laser cutting
of this resistive layer that achieves
tolerance trims the value. The
resistive layer is covered with a
Fig. 2 Chip resistor construction
protective coat. Finally, the eight external terminations (pure Tin) are added. See fig. 2.
DIMENSIONS
Table 1
H
T
a
TYPE
YC124
B
W
1
B (mm)
H (mm)
P (mm)
L (mm)
H2 (mm)
0.20 ±0.15
0.45 ±0.05
0.50 ±0.05
2.00 ±0.10
0.30 ±0.15
0.45 ±0.10
0.30 ±0.15
1.00 ±0.10
W
2
a
P
L
CCB257_a
H
T (mm)
2
W1 (mm)
W2 (mm)
Fig. 3 YC124 series chip resistors dimension
For dimension see Table 1
SCHEMATIC
For dimension see Fig. 3 and Table 1
8
7
6
5
R1
R2
R3
R4
CCA862_b
Fig. 4 Equivalent circuit diagram
1
2
3
4
R1=R2=R3=R4
www.yageo.com
Feb 04, 2005 V.1
Product specification
4
8
SERIES
124 (Pb Free)
YC
Chip Resistor Surface Mount
ELECTRICAL CHARACTERISTICS
FOOTPRINT AND SOLDERING
PROFILES
Table 2
For recommended footprint and
soldering profiles, please see the
special data sheet “Chip resistors
mounting”.
YC124 1/16 W
CHARACTERISTICS
Operating Temperature Range
Maximum Working Voltage
Maximum Overload Voltage
Dielectric Withstanding Voltage
Number of Resistors
–55 °C to +155 °C
50 V
100 V
100 V
4
ENVIRONMENTAL DATA
For material declaration
information (IMDS-data) of the
products, please see the
5% (E24) 10 Ω to 1 MΩ
Resistance Range
1% (E24/E96) 10 Ω to 1 MΩ
separated info “Environmental
data" conformed to EU RoHS.
Zero Ohm Jumper
< 0.05 Ω
±200 ppm/°C
1.0 A
Temperature Coefficient
Jumper Criteria
Rated Current
PACKING STYLE AND PACKAGING QUANTITY
Table 3 Packing style and packaging quantity
PRODUCT TYPE
YC124
PACKING STYLE
REEL DIMENSION
QUANTITY PER REEL
Paper / PE Taping Reel (R)
7" (178 mm)
13" (330 mm)
10,000 units
40,000 units
NOTE
1. For Paper/PE tape and reel specification/dimensions, please see the special data sheet “Packing” document.
FUNCTIONAL DESCRIPTION
POWER RATING
MRA632
P
max
YC124 rated power at 70°C is 1/16 W
(%P
)
rated
100
50
0
RATED VOLTAGE
The DC or AC (rms) continuous working voltage
corresponding to the rated power is determined by
the following formula:
V = √(P X R)
−55
0
50 70 100
T
155
(°C)
amb
Where
V = Continuous rated DC or
AC (rms) working voltage (V)
Fig. 5 Maximum dissipation (P ) in percentage of rated power
max
as a function of the operating ambient temperature (T
)
amb
P = Rated power (W)
R = Resistance value (X)
www.yageo.com
Feb 04, 2005 V.1
Product specification
5
8
SERIES
124 (Pb Free)
YC
Chip Resistor Surface Mount
TESTS AND REQUIREMENTS
Table 4 Test condition, procedure and requirements
TEST
TEST METHOD
PROCEDURE
REQUIREMENTS
MIL-STD-202F-method 304;
JIS C 5202-4.8
Temperature
At +25/–55 °C and +25/+125 °C
Refer to table 2
Coefficient of
Resistance
(T.C.R.)
Formula:
R2 – R1
T.C.R = ------------------------- × 106 (ppm/°C)
R1(t2 – t1)
Where
t1 = +25 °C or specified room temperature
t2 = –55 °C or +125 °C test temperature
R1 = resistance at reference temperature in ohms
R2 = resistance at test temperature in ohms
MIL-STD-202F-method 107G;
IEC 60115-1 4.19
Thermal Shock
At –65 (+0/–10) °C for 2 minutes and at +155
(+10/–0) °C for 2 minutes; 25 cycles
±(0.5% +0.05 Ω) for 1% tol.
±(1.0% +0.05 Ω) for 5% tol.
MIL-R-55342D-Para 4.7.4
Low
Temperature
Operation
At –65 (+0/–5) °C for 1 hour; RCWV applied for ±(0.5% +0.05 Ω) for 1% tol .
45 (+5/–0) minutes
±(1.0% +0.05 Ω) for 5% tol.
No visible damage
MIL-R-55342D-Para 4.7.5;
IEC 60115-1 4.13
Short Time
Overload
2.5 × RCWV applied for 5 seconds at room
temperature
±(1.0% +0.05 Ω) for 1% tol.
±(2.0% +0.05 Ω) for 5% tol.
No visible damage
MIL-STD-202F-method 302;
IEC 60115-1 4.6.1.1
Insulation
Resistance
RCOV for 1 minute
≥10 GΩ
YC124
Type
Voltage (DC)
100 V
MIL-STD-202F-method 301;
IEC 60115-1 4.6.1.1
Dielectric
Withstand
Voltage
Maximum voltage (Vrms) applied for 1 minute
No breakdown or flashover
YC124
Type
Voltage (AC)
100 Vrms
MIL-STD-202F-method 210C;
IEC 60115-1 4.18
Resistance to
Soldering
Heat
Unmounted chips; 260 ±5 °C for 10 ±1 seconds
±(0.5% +0.05 Ω) for 1% tol.
±(1.0% +0.05 Ω) for 5% tol.
No visible damage
MIL-STD-202F-method 108A;
IEC 60115-1 4.25.1
Life
At 70 ±2 °C for 1,000 hours; RCWV applied for
1.5 hours on and 0.5 hour off
±(1% +0.05 Ω) for 1% tol.
±(3% +0.05 Ω) for 5% tol.
www.yageo.com
Feb 04, 2005 V.1
Product specification
6
8
SERIES
124 (Pb Free)
YC
Chip Resistor Surface Mount
TEST
Solderability
TEST METHOD
PROCEDURE
Solder bath at 245 ±3 °C
REQUIREMENTS
MIL-STD-202F-method 208A;
IEC 60115-1 4.17
Well tinned (≥95% covered)
Dipping time: 2 ±0.5 seconds
No visible damage
JIS C 5202.6.14;
Bending
Strength
±(1.0% +0.05 Ω) for 1% tol.
±(1.0% +0.05 Ω) for 5% tol.
No visible damage
Resistors mounted on a 90 mm glass epoxy
resin PCB (FR4)
IEC 60115-1 4.15
Bending: 1 mm
MIL-STD-202F-method 215;
IEC 60115-1 4.29
Resistance to
Solvent
lsopropylalcohol (C3H7OH) or dichloromethane No smeared
(CH2Cl2) followed by brushing
JIS C 5202 5.9;
Noise
Maximum voltage (Vrms) applied.
Value
Resistors range
IEC 60115-1 4.12
R < 100 Ω
10 dB
20 dB
30 dB
40 dB
46 dB
48 dB
100 Ω ≤ R < 1 KΩ
1 KΩ ≤ R < 10 KΩ
10 KΩ ≤ R < 100 KΩ
100 KΩ ≤ R < 1 MΩ
1 MΩ ≤ R ≤ 22 MΩ
JIS C 5202 7.5;
Humidity
(steady state)
1,000 hours; 40 ±2 °C; 93(+2/–3)% RH
±(0.5% +0.05 Ω) for 1% tol.
±(2.0% +0.05 Ω) for 5% tol.
IEC 60115-8 4.24.8
RCWV applied for 1.5 hours on and 0.5 hour off
EIA/IS 4.13B;
Leaching
Solder bath at 260 ±5 °C
No visible damage
IEC 60115-8 4.18
Dipping time: 30 ±1 seconds
JIS C 5202 5.8
On request
Intermittent
Overload
At room temperature; 2.5 × RCWV applied for
1 second on and 25 seconds off; total 10,000
cycles
±(1.0% +0.05 Ω) for 1% tol.
±(2.0% +0.05 Ω) for 5% tol.
Resistance to
Vibration
On request
MIL-STD-202F-method 106F;
IEC 60115-1 4.24.2
Moisture
Resistance
Heat
42 cycles; total 1,000 hours
Shown as Fig. 6
±(0.5% +0.05Ω) for 1% tol.
±(2.0% +0.05Ω) for 5% tol.
No visible damage
www.yageo.com
Feb 04, 2005 V.1
Product specification
7
8
SERIES
124 (Pb Free)
YC
Chip Resistor Surface Mount
80 − 98%
RH
80 − 98%
RH
75
90 − 98% RH
90 − 98% RH
90 − 98% RH
temperature
initial drying
24 hours
[°C]
rate of change of temperature is unspecified,
however, specimens shall not be subjected to
50
radiant heating from chamber conditioning processes
end of final cycle;
measurements
as specified in 2ꢀ7
+10 °C (+18 °F)
−2 °C (−3ꢀ6 °F)
25
0
initial measurements
as specified in 2ꢀ2
circulation of conditioning air shall be at a
minimum cubic rate per minute equivalent to
10 times the volume of the chamber
optional sub-cycle if specified
(2ꢀ3); sub-cycle performed during
any 5 of the first 9 cycles; humidity
uncontrolled during sub-cycle
temperature
tolerance
2 °C ( 3ꢀ6 °F)
unless otherwise
specified
voltage applied as specified in 2ꢀ4
STEP1
STEP2 STEP3
one cycle 24 hours; repeat as specified in 2ꢀ5
10 15
STEP4
STEP5 STEP6
STEP7
prior to first
cycle only
0
5
20
25
HBK073
time [h]
Fig. 6 Moisture resistance test requirements
www.yageo.com
Feb 04, 2005 V.1
Product specification
8
8
SERIES
124 (Pb Free)
YC
Chip Resistor Surface Mount
REVISION HISTORY
REVISION DATE
CHANGE NOTIFICATION DESCRIPTION
Version 1
Feb 04, 2005
-
- New datasheet for 4 × 0402 chip resistor arrays 1% and 5% with lead-
free terminations
- Replace the 4 × 0402 part of pdf files: ARV341_5_PbFree_L_0.pdf and
ARV342_1_PbFree_L_0.pdf
- Test method and procedure updated
-
Version 0
Dec 05, 2003
-
www.yageo.com
Feb 04, 2005 V.1
相关型号:
235002325902L
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 5900ohm, 50V, 1% +/-Tol, 200ppm/Cel, Surface Mount, 0408, CHIP, LEAD FREE
YAGEO
235002325903
Array/Network Resistor, Isolated, 59000ohm, 50V, 1% +/-Tol, 300ppm/Cel, Surface Mount, 0402, CHIP
YAGEO
235002325903L
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 59000ohm, 50V, 1% +/-Tol, 200ppm/Cel, Surface Mount, 0408, CHIP, LEAD FREE
YAGEO
235002325909
Array/Network Resistor, Isolated, 59ohm, 50V, 1% +/-Tol, 300ppm/Cel, Surface Mount, 0402, CHIP
YAGEO
235002325909L
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 59ohm, 50V, 1% +/-Tol, 200ppm/Cel, Surface Mount, 0408, CHIP, LEAD FREE
YAGEO
235002326041L
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 604ohm, 50V, 1% +/-Tol, 200ppm/Cel, Surface Mount, 0408, CHIP, LEAD FREE
YAGEO
235002326044L
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 604000ohm, 50V, 1% +/-Tol, 200ppm/Cel, Surface Mount, 0408, CHIP, LEAD FREE
YAGEO
235002326049L
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 60.4ohm, 50V, 1% +/-Tol, 200ppm/Cel, Surface Mount, 0408, CHIP, LEAD FREE
YAGEO
235002326192L
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 6190ohm, 50V, 1% +/-Tol, 200ppm/Cel, Surface Mount, 0408, CHIP, LEAD FREE
YAGEO
235002326199L
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 61.9ohm, 50V, 1% +/-Tol, 200ppm/Cel, Surface Mount, 0408, CHIP, LEAD FREE
YAGEO
235002326201L
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 620ohm, 50V, 1% +/-Tol, 200ppm/Cel, Surface Mount, 0408, CHIP, LEAD FREE
YAGEO
235002326202L
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 6200ohm, 50V, 1% +/-Tol, 200ppm/Cel, Surface Mount, 0408, CHIP, LEAD FREE
YAGEO
©2020 ICPDF网 联系我们和版权申明