RC0402FRF07137RL [YAGEO]
Fixed Resistor, Metal Glaze/thick Film, 0.0625W, 137ohm, 50V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0402, CHIP, LEAD FREE;型号: | RC0402FRF07137RL |
厂家: | YAGEO CORPORATION |
描述: | Fixed Resistor, Metal Glaze/thick Film, 0.0625W, 137ohm, 50V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0402, CHIP, LEAD FREE |
文件: | 总10页 (文件大小:248K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
GENERAL PURPOSE CHIP RESISTORS
RC0402 (Pb Free)
5%, 1%
Product specification
2
10
SERIES
0402 (Pb Free)
RC
Chip Resistor Surface Mount
SCOPE
This specification describes RC0402 series chip resistors with lead-free terminations made by thick film process.
ORDERING INFORMATION
Part number is identified by the series, size, tolerance, packing type, temperature coefficient, taping reel and
resistance value.
PHYCOMP ORDERING CODE
12NC CODE
CTC CODE
2322
(1)
XXX XXXXX L
RC0402 X X X XX XXXX L
( ) ( ) ( ) ( )
( )
5
( )
6
1
2
3
4
( )
(2)
(3)
4
PAPER / PE TAPE ON REEL (units) (2)
( )
1 TOLERANCE
TYPE/ START TOL. RESISTANCE
0402 IN (1)
(%) RANGE
10,000
20,000/not preferred
50,000
705 87xxx
706 8xxxx
705 91007
F = ±1%
J = ±5%
RC31
2322
±5% 1 to 10 MΩ
±1% 1 to 10 MΩ
705 70xxx
706 7xxxx
705 91001
---
---
---
( )
RC32 2322
Jumper 2322
2 PACKAGING TYPE
-
0 Ω
R = Paper/PE taping reel
( )
3 TEMPERATURE COEFFICIENT
OF RESISTANCE
(1) The resistors have a 12-digit
ordering code starting with
2322.
Last digit of 12NC
Resistance decade (3)
Last digit
– = Base on spec
X
0.01 to 0.0976
0
7
8
9
1
2
3
4
5
6
( )
4 TAPING REEL
(2) The subsequent 4 or 5 digits
indicate the resistor
X
0.1 to 0.976
07 = 7 inch dia. Reel
10 = 10 inch dia. Reel (not preferred)
13 = 13 inch dia. Reel
X
1 to 9.76
tolerance and packaging.
X
10 to 97.6
100 to 976
1 to 9.76 k
(3) The remaining 4 or 3 digits
represent the resistance value
with the last digit indicating
the multiplier as shown in the
table of “Last digit of 12NC”.
X
( )
5 RESISTANCE VALUE
X
5R6, 56R, 560R, 56K, 1M.
X
10 to 97.6 k
X
100 to 976 k
(6) RESISTOR TERMINATIONS
(4) “L” means lead-free
terminations.
X
1 to 9.76 M
L = Lead free terminations (pure Tin)
X
10 to 97.6 M
ORDERING EXAMPLE
X
Example: 0.02
=
=
=
=
=
0200 or 200
3007 or 307
1008 or 108
3303 or 333
1006 or 106
ORDERING EXAMPLE
The ordering code of a RC32
resistor, value 56 X with ±1%
tolerance, supplied in tape of
10,000 units per reel is:
232270675609L.
X
0.3
The ordering code of a RC0402
chip resistor, value 56 X with
±1% tolerance, supplied in 7-inch
X
1
X
33 k
10 M
X
tape reel is: RC0402FR-0756RL.
NOTE
1. The “L” at the end of the code is only for ordering. On the reel label, the standard CTC or 12NC will be mentioned an additional stamp
“LFP”= lead free production.
2. Products with lead in terminations fulfil the same requirements as mentioned in this datasheet.
3. Products with lead in terminations will be phased out in the coming months (before July 1st, 2006)
www.yageo.com
Sep 03, 2004 V.2
Product specification
3
10
SERIES
0402 (Pb Free)
RC
Chip Resistor Surface Mount
MARKING
RC0402
No marking
ynsc007
Fig. 1
CONSTRUCTION
The resistors are constructed out of
a high-grade ceramic body. Internal
metal electrodes are added at each
end and connected by a resistive
paste. The composition of the paste
is adjusted to give the approximate
required resistance and laser cutting
of this resistive layer that achieves
tolerance trims the value. The
resistive layer is covered with a
protective coat.
protective coat
handbook, 4 columns
resistor layer
inner electrode
H
end termination
ceramic substrate MBE940_a
I
2
Fig. 2 Chip resistor construction
Finally, the two external terminations (pure Tin) are added. See fig. 2.
DIMENSIONS
Table 1
protective coat
TYPE
RC0402
I
1
L (mm)
W (mm)
H (mm)
I1 (mm)
I2 (mm)
1.00 ±0.05
0.50 ±0.05
0.35 ±0.05
0.20 ±0.10
0.25 ±0.10
W
MBE940_a
L
For dimension see Table 1
Fig. 3 Chip resistor dimension
www.yageo.com
Sep 03, 2004 V.2
Product specification
4
10
SERIES
0402 (Pb Free)
RC
Chip Resistor Surface Mount
ELECTRICAL CHARACTERISTICS
FOOTPRINT AND SOLDERING
PROFILES
Table 2
For recommended footprint and
soldering profiles, please see the
special data sheet “Chip resistors
mounting”.
RC0402 1/16 W
CHARACTERISTICS
Operating Temperature Range
Maximum Working Voltage
Maximum Overload Voltage
Dielectric Withstanding Voltage
–55 °C to +155 °C
50 V
100 V
100 V
ENVIRONMENTAL DATA
5% (E24) 1 Ω to 10 MΩ
1% (E96) 1 Ω to 10 MΩ
For material declaration
information (IMDS-data) of the
products, please see the
separated info “Environmental
data”.
Resistance Range
Zero Ohm Jumper < 0.05 Ω
10 Ω < R ≤ 10 MΩ ±100 ppm/°C
1 Ω < R ≤ 10 Ω ±200 ppm/°C
Temperature Coefficient
Jumper Criteria
Rated Current
1.0 A
2.0 A
Maximum Current
PACKING STYLE AND PACKAGING QUANTITY
Table 3 Packing style and packaging quantity
PRODUCT TYPE
RC0402
PACKING STYLE
REEL DIMENSION
QUANTITY PER REEL
Paper / PE Taping Reel (R)
7" (178 mm)
10,000 units
20,000 units
50,000 units
10" (254 mm) / not preferred
13" (330 mm)
NOTE
1. For Paper/PE tape and reel specification/dimensions, please see the special data sheet “Packing” document.
www.yageo.com
Sep 03, 2004 V.2
Product specification
5
10
SERIES
0402 (Pb Free)
RC
Chip Resistor Surface Mount
FUNCTIONAL DESCRIPTION
POWER RATING
MRA632
P
max
RC0402 rated power at 70°C is 1/16 W
RATED VOLTAGE
(%P
)
rated
100
50
0
The DC or AC (rms) continuous working voltage
corresponding to the rated power is determined by
the following formula:
V=√(P X R)
−55
0
50 70 100
T
155
(°C)
amb
Where
V=Continuous rated DC or
AC (rms) working voltage (V)
Fig. 4 Maximum dissipation (P ) in percentage of rated power
max
as a function of the operating ambient temperature (T
)
amb
P=Rated power (W)
R=Resistance value (X)
PULSE LOADING CAPABILITIES
CCB508
3
10
^
V
max
1.2/50 µs
10/700 µs
(V)
2
10
10
1
2
3
4
5
6
1
10
10
10
10
10
10
R
(Ω)
n
Fig. 5 Maximum permissible peak pulse voltage without failing to open circuit’ in accordance with DIN IEC 60040 (CO) 533 for type:
RC0402
www.yageo.com
Sep 03, 2004 V.2
Product specification
6
10
SERIES
0402 (Pb Free)
RC
Chip Resistor Surface Mount
CCB509
3
2
10
^
P
max
(V)
10
10
single pulse
1
−1
10
−6
−5
−4
−3
−2
−1
10
10
10
10
10
10
1
t
(s)
i
Fig. 6 Pulse on a regular basis for type: RC0402; maximum permissible peak pulse power as a function of pulse duration for single
pulse and repetitive pulse tp/ti = 1000
CCB507
200
^
V
max
(V)
150
100
50
0
10
−6
−5
−4
−3
−2
−1
10
10
10
10
10
1
t
(s)
i
Fig. 7 Pulse on a regular basis for type: RC0402; maximum permissible peak pulse voltage as a function of pulse duration
www.yageo.com
Sep 03, 2004 V.2
Product specification
7
10
SERIES
0402 (Pb Free)
RC
Chip Resistor Surface Mount
TESTS AND REQUIREMENTS
Table 4 Test condition, procedure and requirements
TEST
TEST METHOD
PROCEDURE
REQUIREMENTS
MIL-STD-202F-method 304;
JIS C 5202-4.8
Temperature
At +25/–55 °C and +25/+125 °C
Refer to table 2
Coefficient of
Resistance
(T.C.R.)
Formula:
R2–R1
T.C.R= ------------------------- ×106 (ppm/°C)
R1(t2–t1)
Where
t1=+25 °C or specified room temperature
t2=–55 °C or +125 °C test temperature
R1=resistance at reference temperature in ohms
R2=resistance at test temperature in ohms
MIL-STD-202F-method 107G;
IEC 60115-1 4.19
Thermal Shock
At –65 (+0/–10) °C for 2 minutes and at +155
(+10/–0) °C for 2 minutes; 25 cycles
±(0.5%+0.05 Ω) for 1% tol.
±(1.0%+0.05 Ω) for 5% tol.
MIL-R-55342D-Para 4.7.4
Low
Temperature
Operation
At –65 (+0/–5) °C for 1 hour; RCWV applied
for 45 (+5/–0) minutes
±(0.5%+0.05 Ω) for 1% tol .
±(1.0%+0.05 Ω) for 5% tol.
No visible damage
MIL-R-55342D-Para 4.7.5;
IEC 60115-1 4.13
Short Time
Overload
2.5 × RCWV applied for 5 seconds at room
temperature
±(1.0%+0.05 Ω) for 1% tol.
±(2.0%+0.05 Ω) for 5% tol.
No visible damage
MIL-STD-202F-method 302;
IEC 60115-1 4.6.1.1
Insulation
Resistance
RCOV for 1 minute
≥10 GΩ
RC0402
Type
Voltage (DC)
100 V
MIL-STD-202F-method 301;
IEC 60115-1 4.6.1.1
Dielectric
Withstand
Voltage
Maximum voltage (Vrms) applied for 1 minute
No breakdown or flashover
RC0402
Type
Voltage (AC)
100 Vrms
MIL-STD-202F-method 210C;
IEC 60115-1 4.18
Resistance to
Soldering
Heat
Unmounted chips; 260 ±5 °C for 10 ±1
seconds
±(0.5%+0.05 Ω) for 1% tol.
±(1.0%+0.05 Ω) for 5% tol.
No visible damage
MIL-STD-202F-method 108A;
IEC 60115-1 4.25.1
Life
At 70±2 °C for 1,000 hours; RCWV applied for
1.5 hours on and 0.5 hour off
±(1%+0.05 Ω) for 1% tol.
±(3%+0.05 Ω) for 5% tol.
www.yageo.com
Sep 03, 2004 V.2
Product specification
8
10
SERIES
0402 (Pb Free)
RC
Chip Resistor Surface Mount
TEST
Solderability
TEST METHOD
PROCEDURE
Solder bath at 245±3 °C
REQUIREMENTS
MIL-STD-202F-method 208A;
IEC 60115-1 4.17
Well tinned (≥95% covered)
Dipping time: 2±0.5 seconds
No visible damage
JIS C 5202.6.14;
Bending
Strength
±(1.0%+0.05 Ω) for 1% tol.
±(1.0%+0.05 Ω) for 5% tol.
No visible damage
Resistors mounted on a 90 mm glass epoxy
resin PCB (FR4)
IEC 60115-1 4.15
Bending: 5 mm
MIL-STD-202F-method 215;
IEC 60115-1 4.29
Resistance to
Solvent
lsopropylalcohol (C3H7OH) or dichloromethane No smeared
(CH2Cl2) followed by brushing
JIS C 5202 5.9;
Noise
Maximum voltage (Vrms) applied.
Value
Resistors range
IEC 60115-1 4.12
R < 100 Ω
10 dB
20 dB
30 dB
40 dB
46 dB
48 dB
100 Ω ≤ R < 1 KΩ
1 KΩ ≤ R < 10 KΩ
10 KΩ ≤ R < 100 KΩ
100 KΩ ≤ R < 1 MΩ
1 MΩ ≤ R ≤ 22 MΩ
JIS C 5202 7.5;
Humidity
(steady state)
1,000 hours; 40±2 °C; 93(+2/–3)% RH
±(0.5%+0.05 Ω) for 1% tol.
±(2.0%+0.05 Ω) for 5% tol.
IEC 60115-8 4.24.8
RCWV applied for 1.5 hours on and 0.5 hour off
EIA/IS 4.13B;
Leaching
Solder bath at 260±5 °C
No visible damage
IEC 60115-8 4.18
Dipping time: 30±1 seconds
JIS C 5202 5.8
On request
Intermittent
Overload
At room temperature; 2.5 × RCWV applied for
1 second on and 25 seconds off; total 10,000
cycles
±(1.0%+0.05 Ω) for 1% tol.
±(2.0%+0.05 Ω) for 5% tol.
Resistance to
Vibration
On request
MIL-STD-202F-method 106F;
IEC 60115-1 4.24.2
Moisture
Resistance
Heat
42 cycles; total 1,000 hours
Shown as Fig. 8
±(0.5%+0.05Ω) for 1% tol.
±(2.0%+0.05Ω) for 5% tol.
No visible damage
www.yageo.com
Sep 03, 2004 V.2
Product specification
9
10
SERIES
0402 (Pb Free)
RC
Chip Resistor Surface Mount
80 − 98%
RH
80 − 98%
RH
75
90 − 98% RH
90 − 98% RH
90 − 98% RH
temperature
initial drying
24 hours
[°C]
rate of change of temperature is unspecified,
however, specimens shall not be subjected to
50
radiant heating from chamber conditioning processes
end of final cycle;
measurements
as specified in 2.7
+10 °C (+18 °F)
−2 °C (−3.6 °F)
25
0
initial measurements
as specified in 2.2
circulation of conditioning air shall be at a
minimum cubic rate per minute equivalent to
10 times the volume of the chamber
optional sub-cycle if specified
(2.3); sub-cycle performed during
any 5 of the first 9 cycles; humidity
uncontrolled during sub-cycle
temperature
tolerance
2 °C ( 3.6 °F)
unless otherwise
specified
voltage applied as specified in 2.4
STEP1
STEP2 STEP3
one cycle 24 hours; repeat as specified in 2.5
10 15
STEP4
STEP5 STEP6
STEP7
prior to first
cycle only
0
5
20
25
HBK073
time [h]
Fig. 8 Moisture resistance test requirements
www.yageo.com
Sep 03, 2004 V.2
Product specification
10
10
SERIES
0402 (Pb Free)
RC
Chip Resistor Surface Mount
REVISION HISTORY
REVISION DATE
CHANGE NOTIFICATION DESCRIPTION
Version 2
Sep 03, 2004
-
- New datasheet for 0402 thick film 1% and 5% with lead-free terminations
- Replace the 0402 part of pdf files: RC01_11_21_31_5,
RC02_12_22_32_10
- Test method and procedure updated
- PE tape added (paper tape will be replaced by PE tape)
www.yageo.com
Sep 03, 2004 V.2
相关型号:
RC0402FRF0713K3L
Fixed Resistor, Metal Glaze/thick Film, 0.0625W, 13300ohm, 50V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0402, CHIP, LEAD FREE
YAGEO
RC0402FRF0713K7L
Fixed Resistor, Metal Glaze/thick Film, 0.0625W, 13700ohm, 50V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0402, CHIP, LEAD FREE
YAGEO
RC0402FRF0713R3L
Fixed Resistor, Metal Glaze/thick Film, 0.0625W, 13.3ohm, 50V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0402, CHIP, LEAD FREE
YAGEO
RC0402FRF0713R7L
Fixed Resistor, Metal Glaze/thick Film, 0.0625W, 13.7ohm, 50V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0402, CHIP, LEAD FREE
YAGEO
RC0402FRF0714K7L
Fixed Resistor, Metal Glaze/thick Film, 0.0625W, 14700ohm, 50V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0402, CHIP, LEAD FREE
YAGEO
RC0402FRF0714R7L
Fixed Resistor, Metal Glaze/thick Film, 0.0625W, 14.7ohm, 50V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0402, CHIP, LEAD FREE
YAGEO
RC0402FRF07165KL
Fixed Resistor, Metal Glaze/thick Film, 0.0625W, 165000ohm, 50V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0402, CHIP, LEAD FREE
YAGEO
RC0402FRF07169R
Fixed Resistor, Metal Glaze/thick Film, 0.0625W, 169ohm, 50V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0402, CHIP, LEAD FREE
YAGEO
RC0402FRF0716R2
Fixed Resistor, Metal Glaze/thick Film, 0.0625W, 16.2ohm, 50V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0402, CHIP, LEAD FREE
YAGEO
RC0402FRF0716R2L
Fixed Resistor, Metal Glaze/thick Film, 0.0625W, 16.2ohm, 50V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0402, CHIP, LEAD FREE
YAGEO
RC0402FRF0716R9L
Fixed Resistor, Metal Glaze/thick Film, 0.0625W, 16.9ohm, 50V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0402, CHIP, LEAD FREE
YAGEO
RC0402FRF0718R2L
Fixed Resistor, Metal Glaze/thick Film, 0.0625W, 18.2ohm, 50V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0402, CHIP, LEAD FREE
YAGEO
©2020 ICPDF网 联系我们和版权申明