RC0402JRF68K [YAGEO]
Fixed Resistor, Metal Glaze/thick Film, 0.0625W, 68000ohm, 50V, 5% +/-Tol, 100ppm/Cel, Surface Mount, 0402, CHIP;型号: | RC0402JRF68K |
厂家: | YAGEO CORPORATION |
描述: | Fixed Resistor, Metal Glaze/thick Film, 0.0625W, 68000ohm, 50V, 5% +/-Tol, 100ppm/Cel, Surface Mount, 0402, CHIP |
文件: | 总12页 (文件大小:354K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Approval Sheet
Thick Film Chip Resistor
RC series
±1% & ±5%
YAGEO CORPORATION
THICK FILM FACTORY
Factory: No.11, Min Chuan Rd., Ta Sheh, Kaohsiung, Taiwan, R.O.C.
Tel: 886-7-351-4117
Fax: 886-7-351-2075
Headquarters: 3F, No.233-1, Pao Chiao Rd., Shin Tien, Taipei, Taiwan,
R.O.C.
Tel: 886-2-2917-7555
Fax: 886-2-2917-4286
URL: www.yageo.com.tw
RC Series
Version 2001-8
Page-1
1. SUBJECT: This specification describes of RC series chip resistors made of
YAGEO Corporation by thick film process.
2. PART NUMBER: Part number of the chip resistor is identified by the series, size,
tolerance, packing style, temperature coefficient, special type and
resistance value.
Example:
RC
0603
F
R
-
07
10K
Series
Name
Size
Code
Resistance
Tolerance
Packing
Style
Temperature
Coefficient
Special
Type
Resistance
Value
of Resistance
(1) Size
Chip: 0201 0402 0603 0805 1206
Power Chip: 1210 2010 2512
(2) Tolerance: F=±1%
J=±5%
(3) Packaging Type: R=Paper Taping Reel.
C=Bulk Cassette.
K=Embossed Taping Reel
(4) T.C.R: E=±50ppm/℃ F=±100ppm/℃ G=±200ppm/℃ - = base on spec
(5) Special Type:
07= 7 inch Dia. Reel
10=10 inch Dia. Reel
13=13 inch Dia. Reel
(6) Resistance Value: 1R、10R、100R、10K、100K、330K、1M………
3. MARKING:
Marking Explanation:
(1) RC0805/RC1206/ RC1210/RC2010/RC2512
Either resistance in E-24 or E-96 series: 4 digits, first three digits are significant
figures, fourth digit is number of zeros.
Value =10KΩ
RC Series
Version 2001-8
Page-2
(2) RC0603/RC0805/RC1206/RC1210/RC2010/RC2512
When resistance in E-24 series: 3 digits, first two digits are significant figures,
third digit is number of zeros.
Value =10KΩ
(3) RC0603
When resistance in E-96 series: 3 digits, use 0603 ±1% EIA-96 marking
method. When ±1% tol in E-24 series,protective layer distinquished with
blue color
Value =12.4 KΩ
EIA-96 MARKING
Code R
Value
Code R
Value
Code R
Value
Code R
Value
Code R
Value
Code R
Value
Code R
Value
Code R
Value
01
100
102
105
107
110
113
115
118
121
124
127
130
13
133
137
140
143
147
150
154
158
162
165
169
174
25
178
182
187
191
196
200
205
210
215
221
226
232
37
237
243
249
255
261
267
274
280
287
294
301
309
49
316
324
332
340
348
357
365
374
383
392
402
412
61
422
432
442
453
464
475
487
499
511
523
536
549
73
562
576
590
604
619
634
649
665
681
698
715
732
85
750
768
787
806
825
845
866
887
909
931
953
976
02
03
04
05
06
07
08
09
10
11
12
14
15
16
17
18
19
20
21
22
23
24
26
27
28
29
30
31
32
33
34
35
36
38
39
40
41
42
43
44
45
46
47
48
50
51
52
53
54
55
56
57
58
59
60
62
63
64
55
66
67
68
69
70
71
72
74
75
76
77
78
79
80
81
82
83
84
86
87
88
89
90
91
92
93
94
95
96
This table shows the first two digits for the three-digit EIA-96 part marking scheme.
The third character is a letter multiplier :
X=10-1 Y=10-2 A=100 B=101 C=10 2 D=10 3 E=10 4 F=10 5
(4) RC0201/0402
RC0201/0402 no marking
0402
0201
RC Series
Version 2001-8
Page-3
4. POWER RATING
(1) Rated Power at 70℃: RC0402=1/16W RC0603=1/10W RC0805=1/8W RC1206=1/4W
RC1210=1/3W
RC2010=3/4W
RC2512=1W RC0201=1/20W
Ambient Temperature(℃)
(2) Rated Voltage: The DC or AC (rms) continuous working voltage corresponding
to the rated power is determined by the following formula:
V= √(P X R)
Where V= Continuous rated DC or AC (rms) working voltage(V)
P= Rated power (W)
R= Resistance value (Ω)
5. ELECTRICAL CHARACTERISTICS
Type
Operating Temp. Range
RC0201 1/20 w
RC0402 1/16 w
RC0603 1/10 w
℃
155
RC0805 1/8 w
-
℃
+
55
~
Maximum Working Voltage 15V
50V
50V
150V
Maximum Overload
50V
300V
100V
100V
Voltage
Dielectric Withstanding
Voltage
300V
50V
100V
100V
1Ω~10MΩ(E-24)
2.2Ω~4.7MΩ(E-96)
Zero Ohm Jumper<0.05Ω
1Ω~22MΩ(E-24)
1Ω~4.7MΩ(E-96)
Zero Ohm Jumper<0.05Ω Zero Ohm Jumper<0.05Ω
1Ω~22MΩ(E-24)
1Ω~4..7MΩ(E-96)
10Ω~1MΩ (E-24)
Resistance Range
Ω
Zero Ohm Jumper<0.05
ꢀ 100ppm/ ℃ (10 Ω ≦ R ≦ ꢀ 100ppm/ ℃ (10 Ω ≦ R ≦
ꢀ 100ppm/ ℃ (10 Ω ≦ R ≦
10MΩ)
ꢀ200ppm/℃(1Ω≦R<10Ω)
ꢀ
1M
℃
Ω ≦
≦
R
200ppm/ (10
Ω
)
Ω
Ω
)
10M
ꢀ 200ppm/ ℃ (1 Ω ≦ R<10 ꢀ 200ppm/ ℃ (1 Ω ≦ R<10
Ω,R>10MΩ Ω,R>10MΩ
)
10M
Temperature Coefficient
)
)
RC Series
Version 2001-8
Page-4
Type
Operating Temp. Range
RC1206 1/4 w
RC1210 1/3 w
RC2010 3/4 w
RC2512 1w
-55℃ ~ +155℃
Maximum Working Voltage 200V
200V
400V
200V
200V
400V
Maximum Overload
400V
400V
Voltage
Dielectric Withstanding
Voltage
500V
500V
500V
500V
1Ω~22MΩ(E-24)
1Ω~22MΩ(E-24)
1Ω~22MΩ(E-24)
1Ω~22MΩ(E-24)
Ω
1
Ω
Ω
Ω
Ω
1
Ω
Ω Ω
1 ~4.7M (E-96)
~4.7M (E-96)
1
~4.7M (E-96)
~4.7M (E-96)
Resistance Range
Zero Ohm Jumper<0.05Ω Zero Ohm Jumper<0.05Ω Zero Ohm Jumper<0.05Ω Zero Ohm Jumper<0.05Ω
ꢀ 100ppm/ ℃ (10 Ω ≦ R ≦ ꢀ 100ppm/ ℃ (10 Ω ≦ R ≦ ꢀ 100ppm/ ℃ (10 Ω ≦ R ≦ ꢀ 100ppm/ ℃ (10 Ω ≦ R ≦
10MΩ)
10MΩ)
10MΩ)
10MΩ)
Temperature Coefficient
ꢀ 200ppm/ ℃ (1 Ω ≦ R<10 ꢀ 200ppm/ ℃ (1 Ω ≦ R<10 ꢀ 200ppm/ ℃ (1 Ω ≦ R<10 ꢀ 200ppm/ ℃ (1 Ω ≦ R<10
Ω,R>10MΩ)
Ω,R>10MΩ)
Ω,R>10MΩ)
Ω,R>10MΩ)
6. DIMENSIONS
7. CONSTRUCTION
Resistor(RuO2)
Overcoat(Epoxy)
Glass
Alumina Substrate
Internal Electrode (Ag-Pd)
Secondery Electrode(Nickel Plated)
External Electorde (Solder Plated)
Unit: mm
Type
L
W
H
I1
I2
0.60±0.10
0.30±0.05
0.25±0.05
0.35±0.05
0.45±0.10
0.50±0.10
0.55±0.10
0.55±0.10
0.55±0.10
0.55±0.10
0.15±0.10
0.20±0.10
0.25±0.15
0.35±0.20
0.45±0.20
0.50±0.20
0.60±0.20
0.60±0.20
0.15±0.10
RC0201
RC0402
RC0603
RC0805
RC1206
RC1210
RC2010
RC2512
1.00±0.10
1.60±0.10
2.00±0.10
3.10±0.10
3.10±0.10
5.00±0.10
6.35±0.10
0.50±0.05
0.80±0.10
1.25±0.10
1.60±0.10
2.60±0.15
2.50±0.15
3.20±0.15
0.25±0.10
0.25±0.15
0.35±0.20
0.40±0.20
0.50±0.20
0.50±0.20
0.50±0.20
RC Series
Version 2001-8
Page-5
8. ENVIRONMENTAL CHARACTERISTICS
(1) Temperature Coefficient of Resistance (T.C.R.)
Test Method:Measure resistance at +25℃ or specified room temperature as
R1, then measure at -55℃ or +155℃ respectively as R2.
Determine the temperature coefficient of resistance from the
following formula.
R
2
-R
T.C.R.= ------------ X 106(PPM/℃ )
(t
-t
1
`
R
1
2
1
)
Where t
1
=+25℃ or specified room temperature
=-55℃ or +155℃ test temperature
t2
R1=resistance at reference temperature in ohms.
R2=resistance at test temperature in ohms.
Acceptance Standard: (Refer to item 5)
(2) Thermal Shock
Test Method:-55±3℃, 2 minutes and +155±2℃, 2 minutes as one cycle.
After 5 cycles, the specimen shall be stabilized at room temp. for
1 hour minimum and then measure the resistance to determine
△R/R(%).
Acceptance Standard:±(0.5%+0.05Ω) for 1% tol.
±(1%+0.05Ω) for 5% tol.
(3) Low Temperature Operation
+0
Test Method:Place the specimen in a test chamber maintained at -65 ℃.
-5
After one hour stabilization+a5t this temperature, full rated working
+5
-0
voltage shall be applied 45-0 minutes. Have15 minutes after
remove the voltage, the specimen shall be removed from the
chamber and stabilized at room temperature for 24 hrs.
Measure the resistance to determine △R/R(%).
RC Series
Version 2001-8
Page-6
Acceptance Standard: ±(0.5%+0.05Ω) for 1% tol .
±(1.0%+0.05Ω) for 5% tol.
& No visible damage
(4) Short Time Overload
Test Method:Apply 2.5 times of rated voltage but not exceeding the maximum
overload voltage for 5 seconds. Have the specimen stabilized at
room temperature for 30 minutes minimum.
Measure the resistance to determine △R/R(%).
Acceptance Standard: ±(1.0%+0.05Ω) for 1% tol.
±(2.0%+0.05Ω) for 5% tol.
& No visible damage
(5) Insulation Resistance
Test Method: Place the specimen in the jig and apply a rated continues
overload voltage (R.C.O.V) for one minute as shown.
Measure the insulation resistance.
Type
Voltage
0201
50V
0402
100V
0603
100V
0805
300V
1206
500V
1210
500V
2010
500V
2512
500V
Acceptance Standard:≧10000MΩ
(6) Dielectric Withstand Voltage
Test Method:Place the specimen in the jig and apply a specified value
continuous overload voltage as shown for one minute.
Type
Voltage
0201
50V
0402
100V
0603
100V
0805
300V
1206
500V
1210
500V
2010
500V
2512
500V
RC Series
Version 2001-8
Page-7
Acceptance Standard:Breakdown voltage>specification and without
open/short
(7) Resistance to Soldering Heat
Test Method:Immerse the specimen in the solder pot at 260±5℃
for 10±1 seconds. Have the specimen stabilized at room
temperature for 30 minutes minimum.
Measure the resistance to determine △R/R(%).
Acceptance Standard:±(0.5%+0.05Ω) for 1% tol.
±(1.0%+0.05Ω) for 5% tol.
& No visible damage
(8) Moisture Resistance
Test Method:Place the specimen in the test chamber, and subjected to 42
damp heat cycles. Each one of which consists of the steps 1 to 7
as figure 1. The total length of test is 1000 hours. After the test,
have the specimen stabilized at room temperature for 24 hours
and measure the resistance to determine △R/R(%).
Acceptance Standard:±(0.5%+0.05Ω) for 1% tol.
±(2.0%+0.05Ω) for 5% tol.
& no visible damage
Fig. 1
Conditions of change of temperature
Version 2001-8
RC Series
Page-8
(9) Life
:
± ℃
Test Method Place the specimen in the oven at 70 2 . Apply the rated voltage
to the specimen at the 1.5 hours on and 0.5 hour off cycle. The
total length of test is 1000 hours. After the test, have the specimen
stabilized at room temperature for one hour minimum and
△
measure the R/R(%).
Acceptance Standard:±(1%+0.05Ω) for 1% tol
±(3%+0.05Ω) for 5% tol
& no visible damage
(10) Solderability
Test Method:Immerse the specimen in the solder pot at 230±5℃ for 5 sec.
Acceptance Standard:At least 95% solder coverage on the termination.
(11) Bending Strength
Test Method:Mount the specimen on a test board as shown in the figure.
Slowly apply the force till the board is bent to specified for
5±1sec,and measure the △R/R(%) at this position.
Acceptance Standard:±(1.0%+0.05Ω) for 1% tol.
±(1.0%+0.05Ω) for 5% tol.
& No visible damage
Type
Bent distance
(d)
0201
0402
0603
0805
1206
1210
2010
2512
3mm
3mm
5mm
5mm
5mm
2mm
2mm
2mm
Unit: mm
RC Series
Version 2001-8
Page-9
(12) Humidity (steady state)
• 英文參考資料:
Humidity (Steady State)
Test Method:The specimen shall be condition in a dry oven at TEMP. of 40±5℃
for a period of 24 Hr. The specimen shall be placed in a chamber and subjected to
a relative humidity of 90 to 95 percent and a temperature of 40℃±2℃ for the
length of time 10000+24 Hr. When length time subjected to a voltage cycle consisting
of rated d.c. Voltage application of 1h 30 min and rest of 30 min repeatedly for
one the test duration’s given in 10000+24 h (42 day). Next, the specimen is taken out
of the test chamber, allowed to stand at room temperature for approximately 24 h,
measured for its resistance values again in accordance with 1-1. And then the
variation in the resistance values taken before and after this test is calculated.
9. TAPING REEL
Unit:mm
Packaging
Tape width
W
T
A
B
C
Style
180+0
60+1
RC0201/RC0402/0603
0805/1206/1210
13.0±0.2
9.0±0.3
11.4±1
Paper
8mm
-3
-0
180+0
60+1
13.0±0.2
13.0±0.3
15.4±1
2010/2512
Embossed
12mm
-3
-0
RC Series
Version 2001-8
Page-10
10. (a)PAPER TAPING
Unit: mm
Dimension
A
B
W
E
F
P
0
P
1
P
2
ΦD
0
T
0.45±0.1 0.75±0.1
8.0±0.2
1.75±0.1 3.5±0.05
1.75±0.1 3.5±0.05
1.75±0.1 3.5±0.05
1.75±0.1 3.5±0.05
1.75±0.1 3.5±0.05
1.75±0.1 3.5±0.05
4.0±0.1
4.0±0.1
4.0±0.1
4.0±0.1
4.0±0.1
4.0±0.1
2.0±0.05 2.0±0.05
2.0±0.05 2.0±0.05
4.0±0.05 2.0±0.05
4.0±0.05 2.0±0.05
4.0±0.05 2.0±0.05
4.0±0.05 2.0±0.05
1.5+0.1
-0
1.5+0.1
-0
1.5+0.1
-0
1.5+0.1
-0
1.5+0.1
-0
1.5+0.1
-0
0.35±0.10
RC 0201
0.65±0.1 1.15±0.1
8.0±0.2
8.0±0.2
8.0±0.2
8.0±0.2
8.0±0.2
0.53±0.10
0.70±0.10
0.85±0.10
0.85±0.10
0.85±0.10
RC 0402
RC 0603
RC 0805
RC 1206
RC 1210
1.1±0.1
1.90±0.1
1.65±0.1 2.40±0.1
1.90±0.1 3.50±0.1
2.80±0.1 3.50±0.1
(b)EMBOSSED TAPING
Feeding hole
D0
Chip pocket
D1
E
A
F
W
B
T
P1
P2
P0
Chip component
Tape running direction
Unit: mm
Dimension
A
B
W
E
F
P
0
P
1
P
2
ΦD
0
ΦD
0
T
2.8±0.2
5.4±0.2
12±0.3
1.75±0.1 5.5±0.05
4.0±0.1
4.0±0.01 2.0±0.05
1.5±0.1
1.5±0.25
1.5±0.25
1.0±0.10
RC 2010
3.5±0.2
6.7±0.2
12±0.3
1.75±0.1 5.5±0.05
4.0±0.1
4.0±0.01 2.0±0.05
1.5±0.1
1.0±0.10
RC 2512
RC Series
Version 2001-8
Page-11
11. PACKING METHODS
PAPER CARRIER
EMBOSSED CARRIER
BULK CASSETTE
Packing
Style
Paper Taping Reel (R)
10" (254mm) 13" (330mm)
Embossed
Taping Reel(K)
7" (178mm)
Bulk
Cassette(C)
7" (178mm)
10,000
10,000
5,000
5,000
5,000
5,000
--
RC0201
RC0402
RC0603
RC0805
RC1206
RC1210
RC2010
RC2512
20,000
20,000
10,000
10,000
10,000
10,000
--
40,000
40,000
20,000
20,000
20,000
20,000
--
--
--
50,000
50,000
25,000
10,000
--
--
--
--
--
--
4,000
4,000
--
--
--
--
--
RC Series
Version 2001-8
Page-12
相关型号:
RC0402JRG079R1L
Fixed Resistor, Metal Glaze/thick Film, 0.0625W, 9.1ohm, 50V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0402, CHIP, LEAD FREE
YAGEO
RC0402JRG10360KL
Fixed Resistor, Metal Glaze/thick Film, 0.0625W, 360000ohm, 50V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0402, CHIP
YAGEO
RC0402JRG106K8
Fixed Resistor, Metal Glaze/thick Film, 0.0625W, 6800ohm, 50V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0402, CHIP
YAGEO
RC0402JRG13390KL
Fixed Resistor, Metal Glaze/thick Film, 0.0625W, 390000ohm, 50V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0402, CHIP
YAGEO
RC0402JRG138K2L
Fixed Resistor, Metal Glaze/thick Film, 0.0625W, 8200ohm, 50V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0402, CHIP
YAGEO
RC0402JRI072R4
Fixed Resistor, Metal Glaze/thick Film, 0.0625W, 2.4ohm, 50V, 5% +/-Tol, 300ppm/Cel, Surface Mount, 0402, CHIP
YAGEO
©2020 ICPDF网 联系我们和版权申明