RC0805FRF10499K [YAGEO]
Fixed Resistor, Metal Glaze/thick Film, 0.125W, 499000ohm, 150V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0805, CHIP;型号: | RC0805FRF10499K |
厂家: | YAGEO CORPORATION |
描述: | Fixed Resistor, Metal Glaze/thick Film, 0.125W, 499000ohm, 150V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0805, CHIP |
文件: | 总7页 (文件大小:217K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
CHIP RESISTORS
RC0805
5%; 1%
2
7
SERIES
0805
RC
Chip Resistor Surface Mount
SCOPE
This specification describes RC 0805 series chip resistors made by thick film process.
ORDERING INFORMATION
Part number is identified by the series, size, tolerance, packing style, temperature coefficient, special type and
resistance value.
MARKING
RC0805 X X X XX XXXX
( ) ( ) ( ) ( )
( )
5
1
2
3
4
RC0805
( )
1 TOLERANCE
F = ±1%
J = ±5%
E-24 series: 3 digits
ynsc001
First two digits for significant figure and 3rd
digit for number of zeros
( )
2 PACKAGING TYPE
Fig. 1 Value=10 KΩ
R = Paper taping reel
C = Bulk case
Both E-24 and E-96 series: 4 digits
( )
3 TEMPERATURE
ynsc004
CHARACTERISTIC OF
RESISTANCE
First three digits for significant figure and
4th digit for number of zeros
Fig. 2 Value=10KΩ
F = ±100ppm/°C
G = ±200ppm/°C
I = ±300ppm/°C
– = Base on spec
CONSTRUCTION
( )
4 SPECIAL TYPE
The resistors are constructed out of a high-grade ceramic body. Internal
metal electrodes are added at each end and connected by a resistive
paste. The composition of the paste is adjusted to give the approximate
required resistance and laser cutting of this resistive layer that achieves
tolerance trims the value. The resistive layer is covered with a protective
coat and printed with the resistance value. Finally, the two external
terminations are added. See fig. 3
07 = 7 inch dia. Reel
10 = 10 inch dia. Reel
13 = 13 inch dia. Reel
( )
5 RESISTANCE VALUE:
5R6, 56R, 560R, 5K6, 56K, 22M.
protective coat
book, 4 columns
resistor layer
inner electrode
H
end termination
ceramic substrate MBE940_a
I
2
Fig. 3 Chip resistor construction
www.yageo.com
Sep. 19, 2003 V.5
3
7
SERIES
0805
RC
Chip Resistor Surface Mount
DIMENSION
Table 1
For dimension see Table 1
TYPE
RC0805
protective coat
I
1
L (mm)
W (mm)
H (mm)
I1 (mm)
I2 (mm)
2.00±0.10
1.25±0.10
0.50±0.10
0.35±0.20
0.35±0.20
W
MBE940_a
L
Fig. 4 Chip resistor dimension
POWER RATING
RATED POWER AT 70°C,
RC0805 1/8W
ELECTRICAL CHARACTERISTICS
Table 2
RC0805 1/8 W
CHARACTERISTICS
Operating Temperature Range
Maximum Working Voltage
Maximum Overload Voltage
Dielectric Withstanding Voltage
–55°C to +155°C
150V
MRA632
umns
P
max
(%P
)
rated
100
50
0
300V
300V
1Ω to 22MΩ (E24)
1Ω to 10MΩ (E96)
Resistance Range
55
0
50 70
100
155
o
(
C)
T
amb
Zero Ohm Jumper<0.05Ω
10Ω< R ≤10MΩ ±100ppm/°C
Temperature Coefficient
Jumper Criteria
Fig. 5 Maximum dissipation (Pmax) in
percentage of rated power as
a function of the operating
1Ω≤ R ≤10Ω; R>10MΩ ±200ppm/°C
Rated Current
2.0A
5.0A
ambient temperature (Tamb
)
Maximum Current
RATED VOLTAGE:
The DC or AC (rms) continuous
working voltage corresponding to
the rated power is determined by
the following formula:
V=√(P X R)
Where
V=Continuous rated DC
or AC (rms) working voltage (V)
P=Rated power (W)
R=Resistance value (X)
www.yageo.com
Sep. 19, 2003 V.5
4
7
SERIES
0805
RC
Chip Resistor Surface Mount
TAPING REEL
Table 3
DIMENSION
Tape Width
ØA (mm)
ØB (mm)
ØC (mm)
W (mm)
For dimension see Table 3
T
RC0805
8mm
180+0/–3
60+1/–0
13.0±0.2
9.0±0.3
21 0.8
C
B
A
T (mm)
11.4±1
Fig. 6 Reel dimension
W
MSA284_a
PAPER TAPE SPECIFICATION
Table 4
P
0
DIMENSION
A (mm)
RC0805
T
P
D
2
0
1.65±0.1
2.4±0.1
E
B (mm)
W (mm)
E (mm)
8.0±0.2
F
cover tape
W
1.75±0.1
3.5±0.05
4.0±0.1
B
P
F (mm)
P0 (mm)
P1 (mm)
P2 (mm)
ØD0 (mm)
T (mm)
4.0±0.05
2.0±0.05
1.5+0.1/–0
0.85±0.10
A
MBD123_a
1
For dimension see Table 4
Fig. 7 Paper tape dimension
PACKING METHOD
LEADER/TRAILER TAPE SPECIFICATION
BULK CASSETTE
slider
shutter
handbook,
4 columns
leader end
coupled
portion
empty compartments
trailer end
with cover tape
(min. 240 mm)
cover tape only
trailer (max. 260 mm)
leader ≥400 mm
MGB377
CCB325
Fig. 8 Leader and trailer tape dimension
Fig. 9 Bulk case outline
Table 5 Packing style and packaging quantity
PACKING STYLE
REEL DIMENSION
7" (178 mm)
RC0805
Paper Taping Reel (R)
5,000
10" (254 mm)
13" (330 mm)
10,000
20,000
10,000
Bulk Cassette (C)
www.yageo.com
Sep. 19, 2003 V.5
5
7
SERIES
0805
RC
Chip Resistor Surface Mount
TYPE
TEST METHOD
ACCEPTANCE STANDARD
Temperature
Coefficient of
Resistance
(T.C.R.)
Measure resistance at
Formula
Refer to table 2
+25°C or specified room
temperature as R1, then
measure at –55°C or
R2–R1
T.C.R. = ------------------------- ×106 (ppm/°C)
R1(t2–t1)
+155°C respectively as R2
Where
Determine the
t1=+25°C or specified room temperature
t2=–55°C or +155°C test temperature
R1=resistance at reference temperature in ohms
R2=resistance at test temperature in ohms
temperature coefficient of
resistance from the
following formula:
Thermal
Shock
At –55±3°C for 2 minutes and at +155±2°C for 2 minutes as one cycle. After 5
cycles, the specimen shall be stabilized at room temp.
±(0.5%+0.05Ω)
Measure the resistance to determine ΔR/R(%) after one more hour.
Low
Temperature
Operation
Place the specimen in a test chamber maintained at –65 (+0/–5)°C. After one hour
stabilization at this temperature, full rated working voltage shall be applied for 45
(+5/–0) minutes. Have15 (+5/–0 ) minutes after remove the voltage, the specimen
shall be removed from the chamber and stabilized at room temperature for 24 hrs.
±(0.5%+0.05Ω) for 1% tol .
±(1.0%+0.05Ω) for 5% tol.
No visible damage
Measure the resistance to determine ΔR/R(%).
Short
Time
Overload
Apply 2.5 times of rated voltage but not exceeding the maximum overload voltage
for 5 seconds. Have the specimen stabilized at room temperature for 30 minutes
minimum.
±(1.0%+0.05Ω)
No visible damage
Measure the resistance to determine ΔR/R(%).
Insulation
Resistance
Place the specimen in the jig and apply a rated
continues overload voltage (R.C.O.V) for one
minute as shown.
≥10,000MΩ
Type
RC0805
Voltage (DC)
300V
Measure the insulation resistance.
Dielectric
Withstand
Voltage
Place the specimen in the jig and apply a
specified value continuous overload voltage as
shown for one minute.
Breakdown voltage>
specification and without
open/short
Type
RC0805
Voltage (AC)
300Vrms
Resistance
To Soldering
Heat
Immerse the specimen in the solder pot at 260±5°C. for 10±1 seconds. Have the
specimen stabilized at room temperature for 30 minutes minimum.
±(0.5%+0.05Ω) for 1% tol.
±(1.0%+0.05Ω) for 5% tol.
No visible damage
Measure the resistance to determine ΔR/R(%).
www.yageo.com
Sep. 19, 2003 V.5
6
7
SERIES
0805
RC
Chip Resistor Surface Mount
TYPE
Moisture
Resistance
TEST METHOD
ACCEPTANCE STANDARD
±(0.5%+0.05Ω) for 1% tol.
±(1.5%+0.05Ω) for 5% tol.
No visible damage
Place the specimen in the test chamber and subject to 42 damp heat cycles. Each
one of which consists of the steps 1 to 7 as figure 11. The total length of test is
1,000 hours. Have the specimen stabilized at room temperature for 24 hours after
testing.
Measure the resistance to determine ΔR/R(%).
Life
Place the specimen in the oven at 70±2°C. Apply the rated voltage to the specimen
at the 1.5 hours on and 0.5 hour off cycle. The total length of test is 1,000 hours.
Have the specimen stabilized at room temperature for one hour minimum after
testing.
±(1%+0.05Ω) for 1% tol.
±(1.5%+0.05Ω) for 5% tol.
No visible damage
Measure the ΔR/R(%).
Solderability
Immerse the specimen in the solder pot at 235±5°C for 5 sec.
At least 95% solder coverage on
the termination
Bending
Strength
Mount the specimen on a test board as
shown in the figure 10. Slowly apply the force
till the board is bent for 5±1 sec.
±(1.0%+0.05Ω) for 1% tol.
±(1.0%+0.05Ω) for 5% tol.
No visible damage
Type
RC0805
Bent Distance (d)
5mm
Measure the ΔR/R(%) at this position.
Fig. 10 Principle of the bending
test
www.yageo.com
Sep. 19, 2003 V.5
7
7
SERIES
0805
RC
Chip Resistor Surface Mount
80 − 98%
RH
80 − 98%
RH
75
90 − 98% RH
90 − 98% RH
90 − 98% RH
temperature
[°C]
initial drying
24 hours
rate of change of temperature is unspecified,
however, specimens shall not be subjected to
radiant heating from chamber conditioning processes
50
25
0
end of final cycle;
measurements
as specified in 2.7
+10 °C (+18 °F)
−2 °C (−3.6 °F)
initial measurements
as specified in 2.2
circulation of conditioning air shall be at a
minimum cubic rate per minute equivalent to
10 times the volume of the chamber
optional sub-cycle if specified
(2.3); sub-cycle performed during
any 5 of the first 9 cycles; humidity
uncontrolled during sub-cycle
temperature
tolerance
±2 °C (±3.6 °F)
unless otherwise
specified
voltage applied as specified in 2.4
STEP1
STEP2 STEP3
one cycle 24 hours; repeat as specified in 2.5
10 15
STEP4
STEP5 STEP6
STEP7
prior to first
cycle only
0
5
20
25
HBK073
time [h]
Fig. 11 Conditions of temperature changing
www.yageo.com
Sep. 19, 2003 V.5
相关型号:
RC0805FRF105M62
Fixed Resistor, Metal Glaze/thick Film, 0.125W, 5620000ohm, 150V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0805, CHIP
YAGEO
RC0805FRF10604K
Fixed Resistor, Metal Glaze/thick Film, 0.125W, 604000ohm, 150V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0805, CHIP
YAGEO
RC0805FRF10604R
Fixed Resistor, Metal Glaze/thick Film, 0.125W, 604ohm, 150V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0805, CHIP
YAGEO
RC0805FRF1060K4
Fixed Resistor, Metal Glaze/thick Film, 0.125W, 60400ohm, 150V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0805, CHIP
YAGEO
RC0805FRF1060R4
Fixed Resistor, Metal Glaze/thick Film, 0.125W, 60.4ohm, 150V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0805, CHIP
YAGEO
RC0805FRF106K81
Fixed Resistor, Metal Glaze/thick Film, 0.125W, 6810ohm, 150V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0805, CHIP
YAGEO
RC0805FRF106M81
Fixed Resistor, Metal Glaze/thick Film, 0.125W, 6810000ohm, 150V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0805, CHIP
YAGEO
RC0805FRF106M81L
Fixed Resistor, Metal Glaze/thick Film, 0.125W, 6810000ohm, 150V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0805, CHIP
YAGEO
RC0805FRF10715R
Fixed Resistor, Metal Glaze/thick Film, 0.125W, 715ohm, 150V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0805, CHIP
YAGEO
RC0805FRF10732K
Fixed Resistor, Metal Glaze/thick Film, 0.125W, 732000ohm, 150V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0805, CHIP
YAGEO
RC0805FRF10732R
Fixed Resistor, Metal Glaze/thick Film, 0.125W, 732ohm, 150V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0805, CHIP
YAGEO
RC0805FRF1073K2
Fixed Resistor, Metal Glaze/thick Film, 0.125W, 73200ohm, 150V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0805, CHIP
YAGEO
©2020 ICPDF网 联系我们和版权申明