RJ1206FRE131R47 [YAGEO]

Fixed Resistor, Thin Film, 0.125W, 1.47ohm, 150V, 1% +/-Tol, -50,50ppm/Cel, 1206,;
RJ1206FRE131R47
型号: RJ1206FRE131R47
厂家: YAGEO CORPORATION    YAGEO CORPORATION
描述:

Fixed Resistor, Thin Film, 0.125W, 1.47ohm, 150V, 1% +/-Tol, -50,50ppm/Cel, 1206,

文件: 总10页 (文件大小:303K)
中文:  中文翻译
下载:  下载PDF数据表文档文件
DATA SHEET  
THIN FILM CHIP RESISTORS  
General purpose  
RJ series (Pb Free)  
1%, TC50  
sizes 0201/0402/0603/0805/  
1206/1210/2010/2512  
Product specification  
2
10  
SERIES  
0201 to 2512 (Pb Free)  
RJ  
Chip Resistor Surface Mount  
SCOPE  
This specification describes RJ0201 to RJ2512 general purpose chip resistors with lead-free terminations made by  
thin film process.  
ORDERING INFORMATION  
Part number is identified by the series, size, tolerance, packing type, temperature coefficient, taping reel and  
resistance value.  
PHYCOMP ORDERING CODE  
12NC CODE  
2390  
XXX XXXXX L  
( )  
4
(1)  
(2)  
(3)  
EMBOSSED TAPE ON REEL(2) PAPER/PE TAPE ON REEL (units) (2)  
RJ  
START TOL. RESISTANCE  
1)  
SIZE IN (  
(%)  
RANGE  
5,000  
10,000  
20,000  
50,000  
4,000  
0201  
0402  
0603  
0805  
1206  
1210  
2010  
2512  
2390  
2390  
2390  
2390  
2390  
2390  
2390  
2390  
±1% 10 to 30 kΩ  
±1% 10 to 121 kΩ  
±1% 3 to 681 kΩ  
±1% 3 to 1.5 MΩ  
±1% 3 to 1.5 MΩ  
±1% 1 to 1 MΩ  
±1% 10 to 1 MΩ  
±1% 10 to 1 MΩ  
-
-
409 8xxxx  
407 8xxxx  
424 8xxxx  
421 8xxxx  
431 8xxxx  
432 8xxxx  
-
429 8xxxx  
427 8xxxx  
444 8xxxx  
441 8xxxx  
451 8xxxx  
412 8xxxx  
-
449 8xxxx  
-
-
447 8xxxx  
-
404 8xxxx  
401 8xxxx  
411 8xxxx  
412 0xxxx  
-
-
-
-
-
-
-
-
-
-
415 8xxxx  
418 8xxxx  
-
-
-
NOTE  
(1) The resistors have a 12-digit  
ordering code starting with  
2390.  
Last digit of 12NC  
Resistance decade (3)  
a. The “L” at the end of the code is only  
for ordering. On the reel label, the  
standard CTC or 12NC will be  
mentioned an additional stamp “LFP”=  
lead free production.  
Last digit  
X
0.01 to 0.0976  
0
7
8
9
1
2
3
4
5
6
(2) The subsequent 4 digits  
indicate the resistor  
X
0.1 to 0.976  
X
1 to 9.76  
tolerance and packaging.  
b. Products with lead in terminations fulfil  
the same requirements as mentioned in  
this datasheet.  
X
10 to 97.6  
100 to 976  
1 to 9.76 k  
(3) The remaining 4 digits  
X
represent the resistance value  
with the last digit indicating  
the multiplier as shown in the  
table of “Last digit of 12NC”.  
X
c. Products with lead in terminations will  
be phased out in the coming months  
(before July 1st, 2006)  
X
10 to 97.6 k  
X
100 to 976 k  
(4) “L” means lead-free  
X
1 to 9.76 M  
(a)  
terminations  
.
X
10 to 97.6 M  
ORDERING EXAMPLE  
X
Example: 0.02  
=
=
=
=
=
0200 or 200  
3007 or 307  
1008 or 108  
3303 or 333  
1006 or 106  
The ordering code of a RJ0603  
resistor, TC50 value 56 X, with  
±1% tolerance, supplied in tape  
of 5,000 units per reel is:  
239040485609L.  
X
0.3  
X
1
X
33 k  
X
10 M  
www.yageo.com  
May 30, 2005 V.1  
Product specification  
3
10  
SERIES  
0201 to 2512 (Pb Free)  
RJ  
Chip Resistor Surface Mount  
CTC CODE  
RJ XXXX F X X XX XXXX L  
ORDERING EXAMPLE  
( )  
1
( ) ( ) ( ) ( )  
( )  
6
( )  
7
2
3
4
5
The ordering code of a RJ0603 chip resistor, TC50  
value 56 X with ±1% tolerance, supplied in 7-inch  
tape reel is: RJ0603FRE0756RL.  
( )  
1 SIZE  
0201  
0402  
0603  
0805  
1206  
1210  
2010  
2512  
NOTE  
a. The “L” at the end of the code is only for ordering. On the reel  
label, the standard CTC will be mentioned an additional stamp  
“LFP”= lead free production.  
b. Products with lead in terminations fulfil the same requirements  
as mentioned in this datasheet.  
c. Products with lead in terminations will be phased out in the  
coming months (before July 1st, 2006)  
( )  
2 TOLERANCE  
F = ±1%  
( )  
3 PACKAGING TYPE  
R = Paper/PE taping reel  
K = Embossed taping reel  
( )  
4 TEMPERATURE COEFFICIENT OF RESISTANCE  
E = 50 ppm/°C  
( )  
5 TAPING REEL  
07 = 7 inch dia. Reel  
10 = 10 inch dia. Reel (not preferred)  
13 = 13 inch dia. Reel  
( )  
6 RESISTANCE VALUE  
5R6, 56R, 560R, 5K6, 56K, 1M.  
(7) RESISTOR TERMINATIONS  
L = Lead free terminations (matte tin) (a)  
www.yageo.com  
May 30, 2005 V.1  
Product specification  
4
10  
SERIES  
0201 to 2512 (Pb Free)  
RJ  
Chip Resistor Surface Mount  
MARKING  
RJ0805 / RJ1206 / RJ1210 / RJ2010 / RJ2512  
Either resistance in E-24 or E-96: 4 digits  
00  
YNSC004  
First three digits for significant figure and 4th digit for number of zeros  
Fig. 1 Value = 10 k  
RJ0603  
E-24 series: 3 digits  
ynsc015  
First two digits for significant figure and 3rd digit for number of zeros  
Fig. 2 Value = 12 kΩ  
10C  
E-96 series: 3 digits for 0603±1% EIA-96 marking method  
ynsc002  
Fig. 3 Value = 12.4 kΩ  
RJ0201 / RJ0402  
No marking  
ynsc007  
Fig. 4  
For marking codes, please see EIA-marking code rules in data sheet “Chip resistors marking”.  
www.yageo.com  
May 30, 2005 V.1  
Product specification  
5
10  
SERIES  
0201 to 2512 (Pb Free)  
RJ  
Chip Resistor Surface Mount  
CONSTRUCTION  
The resistors are constructed out of a high-grade ceramic  
body. Internal metal electrodes are added at each end and  
connected by a resistive layer. The resistive layer is  
adjusted to give the approximate required resistance and  
laser cutting of this resistive layer that achieves tolerance  
trims the value. The resistive layer is covered with a  
protective coat and printed with the resistance value.  
Finally, the two external terminations (matte tin) are  
added. See fig. 5.  
OUTLINES  
For dimension see Table 1  
protective coat  
resistive layer  
inner electrode  
end termination  
H
ceramic substrate  
I
2
protective coat  
I
1
DIMENSION  
Table 1 For outlines see fig. 5  
TYPE  
L (mm) W (mm) H (mm) I1 (mm) I2 (mm)  
0.30 ±0.05 0.25 ±0.05 0.15 ±0.10 0.15 ±0.10  
W
RJ0201  
RJ0402  
RJ0603  
RJ0805  
RJ1206  
RJ1210  
RJ2010  
RJ2512  
0.6 ±0.10  
1.00 ±0.10 0.50 ±0.05 0.30 ±0.05 0.20 ±0.10 0.25 ±0.10  
1.60 ±0.10 0.80 ±0.10 0.45 ±0.10 0.25 ±0.15 0.25 ±0.15  
2.00 ±0.10 1.25 ±0.10 0.50 ±0.10 0.35 ±0.20 0.35 ±0.20  
3.10 ±0.10 1.60 ±0.10 0.55 ±0.10 0.45 ±0.20 0.40 ±0.20  
3.10 ±0.10 2.60 ±0.15 0.55 ±0.10 0.50 ±0.20 0.50 ±0.20  
5.00 ±0.10 2.50 ±0.15 0.55 ±0.10 0.60 ±0.20 0.50 ±0.20  
6.35 ±0.10 3.20 ±0.15 0.55 ±0.10 0.60 ±0.20 0.50 ±0.20  
YNSC056  
L
Fig. 5 Chip resistor outlines  
ELECTRICAL CHARACTERISTICS  
Table 2  
DERATED  
TO  
MAXIMUM  
WORKING  
DIELECTRIC  
WITHSTAND  
VOLTAGE  
MAXIMUM  
TEMPERATURE  
RESISTANCE  
RANGE  
OPERATING  
TYPE  
OVERTOAD COEFFICIENT OF  
TEMPERATURE RANGE  
0 LOAD AT  
VOLTAGE  
VOLTAGE  
RESISTANCE  
±50 ppm/°C  
±50 ppm/°C  
±50 ppm/°C  
±50 ppm/°C  
±50 ppm/°C  
±50 ppm/°C  
±50 ppm/°C  
±50 ppm/°C  
RJ0201  
RJ0402  
RJ0603  
RJ0805  
RJ1206  
RJ1210  
RJ2010  
RJ2512  
10 to 22 KΩ  
1 to 121 KΩ  
1 to 681 KΩ  
1 to 1.5 MΩ  
1 to 1.5 MΩ  
1 to 1 MΩ  
1 to 1 MΩ  
1 to 1 MΩ  
–55 °C to +125 °C  
–55 °C to +125 °C  
–55 °C to +125 °C  
–55 °C to +125 °C  
–55 °C to +125 °C  
–55 °C to +125 °C  
–55 °C to +125 °C  
–55 °C to +125 °C  
+125 °C  
+125 °C  
+125 °C  
+125 °C  
+125 °C  
+125 °C  
+125 °C  
+125 °C  
15 V  
50 V  
100 V  
100 V  
250 V  
250 V  
400 V  
400 V  
400 V  
50 V  
25 V  
100 V  
100 V  
200 V  
250 V  
300 V  
300 V  
300 V  
50 V  
100 V  
150 V  
150 V  
150 V  
150 V  
www.yageo.com  
May 30, 2005 V.1  
Product specification  
6
10  
SERIES  
0201 to 2512 (Pb Free)  
RJ  
Chip Resistor Surface Mount  
FOOTPRINT AND SOLDERING PROFILES  
ENVIRONMENTAL DATA  
For material declaration information (IMDS-data) of  
the products, please see the separated info  
“Environmental data” conformed to EU RoHS.  
For recommended footprint and soldering profiles,  
please see the special data sheet “Chip resistors  
mounting”.  
PACKING STYLE AND PACKAGING QUANTITY  
Table 3 Packing style and packaging quantity  
PACKING STYLE  
REEL DIMENSION RJ0201 RJ0402 RJ0603 RJ0805 RJ1206 RJ1210 RJ2010 RJ2512  
Paper/PE taping reel (R)  
7" (178 mm)  
10" (254 mm) (2)  
13" (330 mm)  
7" (178 mm)  
10,000  
20,000  
50,000  
---  
10,000  
20,000  
50,000  
---  
5,000  
10,000  
20,000  
---  
5,000  
10,000  
20,000  
---  
5,000  
10,000  
20,000  
---  
5,000  
10,000  
20,000  
---  
---  
---  
---  
---  
---  
---  
Embossed taping reel (K)  
4,000  
4,000  
NOTE  
1. For Paper/PE/Embossed tape and reel specification/dimensions, please see the special data sheet “Packing” document.  
2. 10" reel is not preferred typing reel.  
FUNCTIONAL DESCRIPTION  
OPERATINGTEMPERATURE RANGE  
MLB206  
handbook, halfpage  
P
max  
Range: –55°C to +125°C  
(%P  
rated  
)
100  
50  
0
POWER RATING  
Each type rated power at 70°C:  
RJ0201=1/20 W, RJ0402=1/16 W, RJ0603=1/16 W,  
RJ0805=1/10 W, RJ1206=1/8 W, RJ1210=1/4 W,  
RJ2010=1/2 W, RJ2512=3/4 W.  
RATED VOLTAGE  
55  
0
50 70  
100  
T
125  
( C)  
o
amb  
The DC or AC (rms) continuous working voltage  
corresponding to the rated power is determined by  
the following formula:  
Fig. 6 Maximum dissipation (P ) in percentage of rated power  
max  
as a function of the operating ambient temperature (T  
)
amb  
(
)
V = P X R  
Where  
(
)
( )  
V = Continuous rated DC or AC rms working voltage V  
(
)
P = Rated power W  
( )  
R = Resistance value X  
www.yageo.com  
May 30, 2005 V.1  
Product specification  
7
10  
SERIES  
0201 to 2512 (Pb Free)  
RJ  
Chip Resistor Surface Mount  
TESTS AND REQUIREMENTS  
Table 4 Test condition, procedure and requirements  
TEST  
TEST METHOD  
PROCEDURE  
REQUIREMENTS  
MIL-STD-202F-method 304;  
JIS C 5202-4.8  
Temperature  
At +25/–55 °C and +25/+125 °C  
±50 ppm/°C  
Coefficient of  
Resistance  
(T.C.R.)  
Formula:  
R2–R1  
T.C.R= ------------------------- ×106 (ppm/°C)  
R1(t2–t1)  
Where  
t1=+25 °C or specified room temperature  
t2=–55 °C or +125 °C test temperature  
R1=resistance at reference temperature in ohms  
R2=resistance at test temperature in ohms  
MIL-STD-202F-method 107G;  
IEC 60115-1 4.19  
Thermal Shock  
At –65 (+0/–10) °C for 2 minutes and at +125  
(+10/–0) °C for 2 minutes; 25 cycles  
±(0.5%+0.05 )  
MIL-R-55342D-Para 4.7.4  
Low  
Temperature  
Operation  
At –65 (+0/–5) °C for 1 hour; RCWV applied  
for 45 (+5/–0) minutes  
±(0.5%+0.05 )  
No visible damage  
MIL-R-55342D-Para 4.7.5;  
IEC 60115-1 4.13  
Short Time  
Overload  
2.5 × RCWV applied for 5 seconds at room  
temperature  
±(1.0%+0.05 )  
No visible damage  
MIL-STD-202F-method 302;  
IEC 60115-1 4.6.1.1  
Insulation  
Resistance  
RCOV for 1 minute  
10 GΩ  
Details see below table 5  
MIL-STD-202F-method 301;  
IEC 60115-1 4.6.1.1  
Dielectric  
Withstand  
Voltage  
Maximum voltage (Vrms) applied for 1 minute  
Details see below table 5  
No breakdown or flashover  
MIL-STD-202F-method 210C;  
IEC 60115-1 4.18  
Resistance to  
Soldering  
Heat  
Unmounted chips; 260 ±5 °C for 10 ±1  
seconds  
±(0.5%+0.05 )  
No visible damage  
MIL-STD-202F-method 108A;  
IEC 60115-1 4.25.1  
Life  
±(1%+0.05 )  
At 70±2 °C for 1,000 hours; RCWV applied for  
1.5 hours on and 0.5 hour off  
www.yageo.com  
May 30, 2005 V.1  
Product specification  
8
10  
SERIES  
0201 to 2512 (Pb Free)  
RJ  
Chip Resistor Surface Mount  
Table 4 Test condition, procedure and requirements (continued)  
TEST  
Solderability  
TEST METHOD  
PROCEDURE  
REQUIREMENTS  
MIL-STD-202F-method 208A;  
IEC 60115-1 4.17  
Solder bath at 245±3 °C  
Well tinned (95% covered)  
Dipping time: 2±0.5 seconds  
No visible damage  
JIS C 5202.6.14;  
Bending  
Strength  
±(1.0%+0.05 )  
Resistors mounted on a 90 mm glass epoxy resin  
PCB (FR4)  
IEC 60115-1 4.15  
No visible damage  
Bending: see table 6 for each size  
MIL-STD-202F-method 215;  
IEC 60115-1 4.29  
Resistance to  
Solvent  
lsopropylalcohol (C3H7OH) or dichloromethane  
(CH2Cl2) followed by brushing  
No smeared  
< 10 dB  
JIS C 5202 5.9;  
Noise  
Maximum voltage (Vrms) applied.  
IEC 60115-1 4.12  
JIS C 5202 7.5;  
Humidity  
(steady state)  
1,000 hours; 40±2 °C; 93(+2/–3)% RH  
±(0.5%+0.05 )  
IEC 60115-8 4.24.8  
RCWV applied for 1.5 hours on and 0.5 hour off  
EIA/IS 4.13B;  
Leaching  
Solder bath at 260±5 °C  
No visible damage  
IEC 60115-8 4.18  
Dipping time: 30±1 seconds  
JIS C 5202 5.8  
On request  
Intermittent  
Overload  
At room temperature; 2.5 × RCWV applied for 1  
second on and 25 seconds off; total 10,000 cycles  
±(1.0%+0.05 )  
Resistance to  
Vibration  
On request  
MIL-STD-202F-method 106F;  
IEC 60115-1 4.24.2  
Moisture  
Resistance  
Heat  
42 cycles; total 1,000 hours  
Shown as figure 7  
±(0.5%+0.05)  
No visible damage  
Table 5 Criteria of rated continued working voltage and overload voltage  
TYPE  
RJ0201  
RJ0402  
RJ0603  
RJ0805  
RJ1206  
RJ1210  
RJ2010  
RJ2512  
Voltage (DC/unit: V); (AC/ unit: Vrms  
)
50  
100  
100  
300  
500  
500  
500  
500  
Table 6 Bending for sizes 0201 to 2512  
TYPE  
RJ0201  
RJ0402  
RJ0603  
RJ0805  
RJ1206  
RJ1210  
RJ2010  
RJ2512  
Specification (mm)  
2
2
3
3
2
2
2
2
www.yageo.com  
May 30, 2005 V.1  
Product specification  
9
10  
SERIES  
0201 to 2512 (Pb Free)  
RJ  
Chip Resistor Surface Mount  
80 98%  
RH  
80 98%  
RH  
75  
90 98% RH  
90 98% RH  
90 98% RH  
temperature  
initial drying  
24 hours  
[°C]  
rate of change of temperature is unspecified,  
however, specimens shall not be subjected to  
50  
radiant heating from chamber conditioning processes  
end of final cycle;  
measurements  
as specified in 237  
+10 °C (+18 °F)  
2 °C (±36 °F)  
25  
0
initial measurements  
as specified in 232  
circulation of conditioning air shall be at a  
minimum cubic rate per minute equivalent to  
10 times the volume of the chamber  
optional sub-cycle if specified  
(23±); sub-cycle performed during  
any 5 of the first 9 cycles; humidity  
uncontrolled during sub-cycle  
temperature  
tolerance  
±2 °C (±±36 °F)  
unless otherwise  
specified  
voltage applied as specified in 234  
STEP1  
STEP2 STEP±  
one cycle 24 hours; repeat as specified in 235  
10 15  
STEP4  
STEP5 STEP6  
STEP7  
prior to first  
cycle only  
0
5
20  
25  
HBK07±  
time [h]  
Fig. 7 Moisture resistance test requirements  
www.yageo.com  
May 30, 2005 V.1  
Product specification  
10  
10  
SERIES  
0201 to 2512 (Pb Free)  
RJ  
Chip Resistor Surface Mount  
REVISION HISTORY  
REVISION DATE  
CHANGE NOTIFICATION DESCRIPTION  
Version 1  
May 30, 2005 -  
- New datasheet for thin film general purpose chip resistors sizes of  
0201/0402/0603/0805/1206/1210/2010/2512 1% , TC50 with lead-free  
terminations  
www.yageo.com  
May 30, 2005 V.1  

相关型号:

RJ1206FRE1359K

Fixed Resistor, Thin Film, 0.125W, 59000ohm, 150V, 1% +/-Tol, 50ppm/Cel, Surface Mount, 1206, CHIP, ROHS COMPLIANT
YAGEO

RJ1206FRE1360K4L

Fixed Resistor, Metal Film, 0.125W, 60400ohm, 150V, 1% +/-Tol, 50ppm/Cel, Surface Mount, 1206, CHIP, HALOGEN FREE EPOXY AND ROHS COMPLIANT
YAGEO

RJ1206FRE7147KL

THIN FILM CHIP RESISTOR, CHIP, HALOGEN FREE EPOXY AND ROHS COMPLIANT
YAGEO

RJ1206FRE715R4L

THIN FILM CHIP RESISTOR, CHIP, HALOGEN FREE EPOXY AND ROHS COMPLIANT
YAGEO

RJ1206FRE7196KL

THIN FILM CHIP RESISTOR, CHIP, HALOGEN FREE EPOXY AND ROHS COMPLIANT
YAGEO

RJ1206FRE740K2L

THIN FILM CHIP RESISTOR, CHIP, HALOGEN FREE EPOXY AND ROHS COMPLIANT
YAGEO

RJ1206FRE7536RL

THIN FILM CHIP RESISTOR, CHIP, HALOGEN FREE EPOXY AND ROHS COMPLIANT
YAGEO

RJ1206FRE7576KL

THIN FILM CHIP RESISTOR, CHIP, HALOGEN FREE EPOXY AND ROHS COMPLIANT
YAGEO

RJ1206FRE7576RL

THIN FILM CHIP RESISTOR, CHIP, HALOGEN FREE EPOXY AND ROHS COMPLIANT
YAGEO

RJ1206FRE757K6L

THIN FILM CHIP RESISTOR, CHIP, HALOGEN FREE EPOXY AND ROHS COMPLIANT
YAGEO

RJ1206FRE757R6L

THIN FILM CHIP RESISTOR, CHIP, HALOGEN FREE EPOXY AND ROHS COMPLIANT
YAGEO

RJ1206FRE773R2L

THIN FILM CHIP RESISTOR, CHIP, HALOGEN FREE EPOXY AND ROHS COMPLIANT
YAGEO