ZHX1810MV115THTR [ZILOG]
Slim Series SIR Transceiver; 修身系列SIR收发器型号: | ZHX1810MV115THTR |
厂家: | ZILOG, INC. |
描述: | Slim Series SIR Transceiver |
文件: | 总20页 (文件大小:883K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
ZHX1810
Slim Series SIR
Transceiver
Product Specification
PS009313-1202
ZiLOG Worldwide Headquarters • 532 Race Street • San Jose, CA 95126-3432
Telephone: 408.558.8500 • Fax: 408.558.8300 • www.ZiLOG.com
This publication is subject to replacement by a later edition. To determine whether
a later edition exists, or to request copies of publications, contact:
ZiLOG Worldwide Headquarters
532 Race Street
San Jose, CA 95126-3432
Telephone: 408.558.8500
Fax: 408.558.8300
www.ZiLOG.com
ZiLOG is a registered trademark of ZiLOG Inc. in the United States and in other countries. All other
products and/or service names mentioned herein may be trademarks of the companies with which
they are associated.
Document Disclaimer
©2002 by ZiLOG, Inc. All rights reserved. Information in this publication concerning the devices,
applications, or technology described is intended to suggest possible uses and may be superseded.
ZiLOG, INC. DOES NOT ASSUME LIABILITY FOR OR PROVIDE A REPRESENTATION OF
ACCURACY OF THE INFORMATION, DEVICES, OR TECHNOLOGY DESCRIBED IN THIS
DOCUMENT. ZiLOG ALSO DOES NOT ASSUME LIABILITY FOR INTELLECTUAL PROPERTY
INFRINGEMENT RELATED IN ANY MANNER TO USE OF INFORMATION, DEVICES, OR
TECHNOLOGY DESCRIBED HEREIN OR OTHERWISE. Devices sold by ZiLOG, Inc. are covered
by warranty and limitation of liability provisions appearing in the ZiLOG, Inc. Terms and Conditions of
Sale. ZiLOG, Inc. makes no warranty of merchantability or fitness for any purpose. Except with the
express written approval of ZiLOG, use of information, devices, or technology as critical components
of life support systems is not authorized. No licenses are conveyed, implicitly or otherwise, by this
document under any intellectual property rights.
PS009313-1202
ZHX1810
Slim SIR Transceiver
iii
Table of Contents
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
LEDA LED Driver Anode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
TXD Transmit Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
RXD/Receive Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
SD Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
VCC Positive Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
GND Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
TAB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Recommended Application Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Electrical and Timing Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Mechanical Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Soldering and Cleaning Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Reflow Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Manual Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Packing, Storage, and Baking Recommendations . . . . . . . . . . . . . . . . . . . . . . 11
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Baking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Moisture-Proof Packing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Taping Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Customer Feedback Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Customer Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Return Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Problem Description or Suggestion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
PS009313-1202
Table of Contents
ZHX1810
Slim SIR Transceiver
iv
List of Figures
Figure 1. Slim SIR Transceiver Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . 2
Figure 2. Application Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Figure 3. I -Ie Characteristics (0°) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
F
Figure 4. I -LEDA Characteristics (0°) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
F
Figure 5. Directive Characteristics (Emitting) . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Figure 6. Directive Characteristics (Receiving) . . . . . . . . . . . . . . . . . . . . . . . . . 7
Figure 7. ZHX1810 Mechanical Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Figure 8. Alternative ZHX1810 Mechanical Drawing . . . . . . . . . . . . . . . . . . . . 9
Figure 9. Temperature Profile at the Top Surface of ZHX1810 . . . . . . . . . . . 10
Figure 10. ZHX1810 Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Figure 11. ZHX1810 Reel Dimensions (Unit: mm) . . . . . . . . . . . . . . . . . . . . . . 13
Figure 12. ZHX1810 Tape Dimensions and Configuration (Unit: mm) . . . . . . . 14
List of Tables
Table 1. Pin Out for the ZHX1810 Transceiver . . . . . . . . . . . . . . . . . . . . . . . . 2
Table 2. Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Table 3. Recommended Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . 5
Table 4. Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
PS009313-1202
List of Figures and Tables
ZHX1810
Slim SIR Transceiver
1
Description
The ZILOG ZHX1810 is a low-profile version of ZiLOG’s popular ZHX1010
1-meter transceiver. The transceiver is mechanically enhanced for ultra compact,
power-conscious portable products, such as mobile phones, portable printers,
handheld computers, and personal data assistants (PDAs). Designed to operate
using the IrDA-Data mode, the transceiver combines an infrared emitting diode
(IRED) emitter, a PIN photodiode detector, a digital AC coupled LED driver, and a
receiver/decoder in a single package.
The ZILOG ZHX1810 provides an efficient implementation of the SIR standard in
a small-outline footprint format. Application circuit space is also minimized, as only
three components are required.
ZHX1810 also features an independently controlled shutdown that minimizes cur-
rent draw to a maximum of 1 ꢀA.
Features
•
•
•
•
•
•
•
•
Compliant to IrDA Data Specification SIR
Wide power supply voltage range, 2.4 to 5.5 V
Minimum link distance, 1 M
Low-power, listening current, 90 ꢀA (typical) at 3.0 V
Slim form factor (9.1 mm long x 3.8 mm wide x 2.73 mm high)
Only two external components required
Extended operating temperature range (–30 °C to +85 °C)
Meets IEC 825-1 Class 1 Eye Safety Specifications
PS009313-1202
ZHX1810
Slim SIR Transceiver
2
Block Diagram
Figure 1 is the block diagram for the Slim SIR transceiver.
Figure 1. Slim SIR Transceiver Block Diagram
Pin Descriptions
The ZHX1810 transceiver uses the pins listed in Table 1. The pins are described
in this section.
Table 1. Pin Out for the ZHX1810 Transceiver
Pin
1
Name
LEDA
TXD
RXD
SD
Function
I/O
—
I
IRED anode
2
Transmitter input
Receiver output
Enables shutdown mode
Supply voltage
Ground
3
O
I
4
5
V
—
—
—
CC
6
GND
TAB
—
Shield ground
PS009313-1202
ZHX1810
Slim SIR Transceiver
3
LEDA LED Driver Anode
(Power)
This output is connected to the LED anode. Current to the LED is sourced through
an external resistor.
TXD Transmit Data
(Input, active high)
This CMOS input is used to transmit serial data. This input has an internal pull-
down resistor that is disabled (open-circuited) during shutdown.
RXD/Receive Data
(Output, active low)
This output indicates received serial data. It is a tri-state, slew rate controlled
CMOS output (tri-stated during shutdown) driver capable of driving a standard
CMOS load. No external resistor is required.
SD Shutdown
(Input, active high)
This input is used to place the integrated circuit into shutdown mode. Module shut-
down current is influenced by the choice of capacitor used from V to ground.
CC
VCC Positive Supply
(Power)
Connect to positive power supply (2.4–5.5 V). Filter with a 0.33-ꢀF ceramic
bypass capacitor and terminating resistor as close as possible to the V pin.
CC
GND Ground
(Power)
Connect to ground of the power supply. A solid ground plane is recommended for
proper operation.
TAB
(Shield)
The Shield tab must be soldered to the ground plane.
PS009313-1202
ZHX1810
Slim SIR Transceiver
4
Recommended Application Circuits
Figure 2 shows application block diagrams for the ZHX1810 transceiver.
Figure 2. Application Block Diagrams
PS009313-1202
ZHX1810
Slim SIR Transceiver
5
Electrical and Timing Specifications
Table 2 through Table 4 present the electrical and timing specifications for the
ZHX1810 transceiver.
Table 2. Absolute Maximum Ratings
Parameter
Symbol Minimum Maximum Unit Comment
Supply Voltage
Input Voltage
V
V
V
–0.3
6.0
V
V
V
V , GND
cc
TxD, SD
RxD
cc
GND–0.3 V +0.3
IN
cc
Output (External) Voltage
LED Current
GND–0.3 V +0.3
cc
OUT
LED
I
700
mA 20% duty cycle,
Ta=25 °C,
t
<90 ꢀS
ON
Storage Temperature
Solder Temperature
T
T
–40
100
240
°C
°C
ST
SOL
Table 3. Recommended Operating Conditions
Parameter
Symbol
Minimum
2.4
Maximum
Unit
V
Supply Voltage
V
5.5
6.0
85
cc
LED Voltage
VLED
2.4
V
Ambient Operating Temperature
T
–30
°C
OP
Table 4. Electrical Characteristics
Symbol Condition
Parameter
Min Typical
0.6 V
Max
V +0.5
Unit Remarks
High-Level Input Voltage
Low-Level Input Voltage
V
V
V
V
TXD, SD
TXD, SD
RxD
IH
IL
cc
cc
–0.5
2.2
0.2 V
cc
High-Level Output Voltage V
V
OH
OL
LED
CC
CC
Low-Level Output Voltage
Transmitter Current
Listening Current
V
0.4
V
RxD
I
I
I
300
90
mA
ꢀA
ꢀA
150
150
Receive Current
90
Unless otherwise noted: V =3.3 V, GND= 0 V, T = 25 °C
cc
A
PS009313-1202
ZHX1810
Slim SIR Transceiver
6
Table 4. Electrical Characteristics (Continued)
Symbol Condition Min Typical
Parameter
Max
Unit Remarks
Standby Current
I
1
ꢀA
SD=V ,
cc
STB
TxD=0 V
Optical Rise/Fall Time
RxD Pulse Width
t , t
100
1.6
nS
Rr Rf
t
SIR=115.2
Kbps
1.1
40
3.9
ꢀS
PWA
Power Shutdown Time
Startup Time
T
T
T
1
ꢀS
ꢀS
ꢀs
SD
STU
L
200
Receiver Latency
Trans. Radiant Intensity
100
I
I
=260 mA
100
3
mW/sr ꢁh,
E
LED
ꢁv<(+15L)
2
Min. Threshold Irradiance
Angle of Half Intensity
E
V =3.3 V
2
ꢀW/cm ꢁh,
emin
cc
ꢁv<(+15L)
ꢁ
20
°
Hor. and
Vert.
Light Pulse Rise, Fall Time t , t
40
20
nS
ꢀS
%
or of
OPW
OPO
Optical Pulse Width
Optical Overshoot
Peak Wavelength
t
t
TxD=“H”
3
870
nm
ꢂ
P
Unless otherwise noted: V =3.3 V, GND= 0 V, T = 25 °C
cc
A
Figure 3 through Figure 6 show various electrical characteristics.
Figure 3. IF-Ie Characteristics (0°)
PS009313-1202
ZHX1810
Slim SIR Transceiver
7
Figure 4. IF-LEDA Characteristics (0°)
Figure 5. Directive Characteristics (Emitting)
Figure 6. Directive Characteristics (Receiving)
PS009313-1202
ZHX1810
Slim SIR Transceiver
8
Mechanical Drawings
In order to achieve the lowest possible lead times, ZiLOG maintains two assembly
facilities. The mechanical drawings for these transceivers are shown in Figure 7
and Figure 8. These devices, which show minor mechanical differences, are func-
tionally equivalent in every way and meet all ZiLOG and IrDA standards and spec-
ifications. Although reels are never mixed, ZiLOG reserves the right to ship from
either facility in order to meet delivery requirements.
Figure 7. ZHX1810 Mechanical Drawing
PS009313-1202
ZHX1810
Slim SIR Transceiver
9
Figure 8. Alternative ZHX1810 Mechanical Drawing
PS009313-1202
ZHX1810
Slim SIR Transceiver
10
Soldering and Cleaning Recommendations
Follow these recommendations to maintain the performance of the ZHX1810
transceiver.
Reflow Soldering
•
Reflow soldering paste is recommended:
Melting temperature: 178 °C ~ 192 °C
Composition: Sn 63%, Pb 37%
•
The recommended thickness of the metal mask is between 0.2 mm and
0.25 mm for screen printing.
•
•
Number of soldering times: 2 times maximum
The temperature profile at the top surface of ZHX1810, shown in Figure 9, is
recommended.
Figure 9. Temperature Profile at the Top Surface of ZHX1810
Manual Soldering
•
Use 63/37 or silver solder.
Use a soldering iron of 25 W or smaller. Adjust the temperature of the
soldering iron below 300 °C.
•
•
•
Finish soldering within 3 seconds.
Handle only after ZHX1810 has cooled off.
PS009313-1202
ZHX1810
Slim SIR Transceiver
11
Cleaning
Perform cleaning after soldering under the following conditions:
•
•
•
Cleaning agent: Alcohol
Temperature and time: 30 seconds below 50 °C or 3 minutes below 30 °C
Ultrasonic cleaning: Below 20 W
Packing, Storage, and Baking Recommendations
Follow these recommendations to maintain the performance of the ZHX1810
transceiver.
Storage
To avoid moisture absorption, ZHX1810 reels must remain in the original,
unopened moisture-proof packing. Parts must be soldered within 72 hours after
unpacking. Reels that have been unpacked, but will not be soldered within 72
hours, must be stored in a desiccator.
Baking
Parts that have been stored over 12 months or unpacked over 72 hours must be
baked under the following guidelines.
Reels
60 °C for 48 hours or more
Loose Parts
•
•
•
100 °C for 4 hours or more
or
125 °C for 2 hours or more
or
150 °C for 1 hour or more
PS009313-1202
ZHX1810
Slim SIR Transceiver
12
Moisture-Proof Packing
In order to avoid moisture absorption during transportation and storage, ZHX1810
reels are packed in aluminum envelopes (see Figure 10) that contain a desiccant
with a humidity indicator. While this packaging is an impediment to moisture
absorption, it is by no means absolute, and no warranty is implied. The user should
store these parts in a controlled environment to prevent moisture entry. Please read
the label on the aluminum bag for indicator instructions.
Figure 10. ZHX1810 Packaging
PS009313-1202
ZHX1810
Slim SIR Transceiver
13
Taping Specifications
Figure 11 shows the reel dimensions for the ZHX1810. Figure 12 shows the tape
dimensions and configuration for the ZHX1810.
Figure 11. ZHX1810 Reel Dimensions (Unit: mm)
PS009313-1202
ZHX1810
Slim SIR Transceiver
14
Figure 12. ZHX1810 Tape Dimensions and Configuration (Unit: mm)
PS009313-1202
ZHX1810
Slim SIR Transceiver
15
Ordering Information
To order ZHX1810, use ZiLOG part number ZHX1810MV115THTR.
Note:
In order to ensure the lowest possible lead times, ZiLOG uses
two different fab sources for the transceiver IC. Both of these
ICs have been extensively tested and qualified to meet the
ZHX1810 transceiver specifications.
PS009313-1202
ZHX1810
Slim SIR Transceiver
16
Customer Feedback Form
If you experience any problems while operating the ZHX1810 transceiver, or if you note
any inaccuracies while reading this product specification, please copy and complete this
form, then mail or fax it to ZiLOG (see "Return Information," below). We also welcome
your suggestions!
Customer Information
Name
Company
Address
Country
Phone
Fax
City/State/Zip
email
Product Information
Serial # or Board Fab #/Rev #
Software Version
Document Number
Host Computer Description/Type
Return Information
ZiLOG
System Test/Customer Support
532 Race Street
San Jose, CA 95126-3432
Fax: (408) 558-8300
Email: zservice@zilog.com
Problem Description or Suggestion
Provide a complete description of the problem or your suggestion. If you are reporting a
specific problem, include all steps leading up to the occurrence of the problem. Attach
additional pages as necessary.
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
PS009313-1202
相关型号:
©2020 ICPDF网 联系我们和版权申明