ELW2611S(TB)

更新时间:2025-05-19 12:59:56
品牌:EVERLIGHT
描述:Logic IC Output Optocoupler

ELW2611S(TB) 概述

Logic IC Output Optocoupler 光耦合器

ELW2611S(TB) 规格参数

是否Rohs认证: 符合生命周期:Active
包装说明:DIP-8Reach Compliance Code:compliant
风险等级:5.73其他特性:CMOS COMPATIBLE, UL APPROVED
配置:SINGLE标称数据速率:10 MBps
最大正向电流:0.05 A最大绝缘电压:5000 V
安装特点:SURFACE MOUNT元件数量:1
功能数量:1最大通态电流:0.05 A
最高工作温度:85 °C最低工作温度:-40 °C
光电设备类型:LOGIC IC OUTPUT OPTOCOUPLER包装方法:TR
标称响应时间:4e-8 ns形状:RECTANGULAR
表面贴装:YESBase Number Matches:1

ELW2611S(TB) 数据手册

通过下载ELW2611S(TB)数据手册来全面了解它。这个PDF文档包含了所有必要的细节,如产品概述、功能特性、引脚定义、引脚排列图等信息。

PDF下载
ELW137  
ELW26XX series  
8 PIN DIP WIDE BODY HIGH SPEED  
10MBit/s LOGIC GATE PHOTOCOUPLER  
Features:  
High speed 10Mbit/s  
Guaranteed performance from -40 to 85  
Logic gate output  
High isolation voltage between input  
and output (Viso=5000 V rms )  
Pb free and RoHS compliant.  
UL approved (No. 214129)  
VDE approved (No. 132249)  
SEMKO approved  
NEMKO approved  
DEMKO approved  
FIMKO approved  
CSA approved (No. 2037145)  
Schematic  
Description  
1
8
The ELW137, ELW2601 and ELW2611 consists of an  
infrared emitting diode optically coupled to a high speed  
integrated photo detector logic gate with a strobable output.  
It is packaged in a 8-pin wide body package and  
available SMD options.  
2
3
4
7
6
5
Applications  
A 0.1µF bypass capacitor must be  
connected between pins 8 and 5 *3  
Ground loop elimination  
LSTTL to TTL, LSTTL or 5 volt CMOS  
Line receiver, data transmission  
Data multiplexing  
Pin Configuration  
1, No Connection  
2, Anode  
Switching power supplies  
Pulse transformer replacement  
Computer peripheral interface  
3, Cathode  
4. No Connection  
5, Gnd  
6, Vout  
Truth Table (Positive Logic)  
7, V  
8, V  
E
Input  
H
Enable  
Output  
CC  
H
H
L
H
H
H
L
L
H
L
L
L
H
NC  
NC  
L
H
Everlight Electronics Co., Ltd.  
Document No DPC-0000115  
1
http://www.everlight.com  
June 23, 2011  
Rev. 1  
ELW137  
ELW26XX series  
8 PIN DIP WIDE BODY HIGH SPEED  
10MBit/s LOGIC GATE PHOTOCOUPLER  
Absolute Maximum Ratings (Ta=25°C)  
Parameter  
Symbol  
Rating  
50  
Unit  
mA  
V
Forward current  
IF  
Enable input voltage Not exceed VCC by  
more than 500mV  
VE  
5.5  
Input  
VR  
PD  
PC  
Reverse voltage  
Power dissipation  
Power dissipation  
5
V
100  
85  
mW  
mW  
IO  
Output current  
Output voltage  
Supply voltage  
50  
7.0  
mA  
V
Output  
VO  
VCC  
PO  
7.0  
V
Output Power Dissipation  
Isolation voltage *1  
100  
mW  
V rms  
°C  
VISO  
TOPR  
TSTG  
TSOL  
5000  
Operating temperature  
Storage temperature  
Soldering temperature *2  
-40 ~ +85  
-55 ~ +125  
260  
°C  
°C  
Notes  
*1 AC for 1 minute, R.H.= 40 ~ 60% R.H. In this test, pins 1 , 2 , 3 & 4 are shorted together, and pins 5 , 6 , 7  
& 8 are shorted together.  
*2 For 10 second  
Everlight Electronics Co., Ltd.  
Document No DPC-0000115  
2
http://www.everlight.com  
June 23, 2011  
Rev. 1  
ELW137  
ELW26XX series  
8 PIN DIP WIDE BODY HIGH SPEED  
10MBit/s LOGIC GATE PHOTOCOUPLER  
Electrical Characteristics (Ta=-40 to 85°C unless specified otherwise)  
Input  
Parameter  
Forward voltage  
Symbol  
VF  
Min.  
Typ.*  
1.4  
-
Max.  
Unit  
V
Condition  
IF = 10mA  
-
5.0  
-
1.8  
Reverse voltage  
-
-
-
V
IR = 100µA, TA=25  
VR  
Temperature coefficient of  
forward voltage  
-1.9  
70  
mV/°C  
pF  
VF  
/
TA  
IF =10mA  
Input capacitance  
-
CIN  
VF=0, f=1MHz  
Output  
Parameter  
Symbol  
Min.  
-
Typ.*  
6.5  
Max.  
10  
Unit  
Condition  
IF=0mA, VE=0.5V,  
VCC=5.5V  
High level supply current  
Low level supply current  
High level enable current  
Low level enable current  
High level enable voltage  
Low level enable voltage*4  
ICCH  
ICCL  
mA  
mA  
IF=10mA, VE=0.5V,  
VCC=5.5V  
-
-
8
- 0.6  
- 0.8  
-
13  
-1.6  
-1.6  
-
mA  
mA  
V
IEH  
IEL  
VE=2.0V, VCC=5.5V  
VE=0.5V, VCC=5.5V  
IF=10mA, VCC=5.5V  
IF=10mA, VCC=5.5V  
-
2.0  
-
VEH  
VEL  
-
0.8  
V
Transfer Characteristics (Ta=-40 to 85°C unless specified otherwise)  
Parameter  
Symbol  
IOH  
Min.  
-
Typ.*  
2.1  
Max.  
100  
Unit  
uA  
Condition  
VCC=5.5V, VO=5.5V,  
IF=250mA, VE=2.0V  
HIGH Level Output Current  
VCC = 5.5V, IF=5mA,  
VE=2.0V,  
LOW Level Output Current  
Input Threshold Current  
-
-
0.35  
3.0  
0.6  
5
VOL  
V
ICL(Sinking)=13mA  
VCC= 5.5V, VO=0.6V,  
VE=2.0V,  
IFT  
mA  
IOL(Sinking)=13mA  
Everlight Electronics Co., Ltd.  
Document No DPC-0000115  
3
http://www.everlight.com  
June 23, 2011  
Rev. 1  
ELW137  
ELW26XX series  
8 PIN DIP WIDE BODY HIGH SPEED  
10MBit/s LOGIC GATE PHOTOCOUPLER  
Switching Characteristics (Ta=-40 to 85°C, VCC=5V, IF=7.5mA unless specified otherwise)  
Parameter  
Symbol  
TPHL  
Min.  
-
Typ.*  
35  
Max.  
100  
Unit  
ns  
Condition  
Propagation delay time to  
output High level*5  
(Fig.12)  
CL = 15pF, RL=350,  
TA=25°C  
Propagation delay time to  
output Low level*6  
(Fig.12)  
CL = 15pF, RL=350,  
TA=25°C  
-
40  
100  
TPLH  
ns  
Pulse width distortion  
-
-
-
5
40  
-
CL = 15pF, RL=350Ω  
CL = 15pF, RL=350Ω  
CL = 15pF, RL=350Ω  
|Tphl – Tplh|  
ns  
ns  
ns  
Output rise time  
(Fig.12)*7  
40  
10  
tr  
tf  
Output fall time  
(Fig.12)*8  
-
Switching Characteristics (Ta=-40 to 85°C, VCC=5V, IF=7.5mA unless specified otherwise)  
Enable Propagation Delay  
IF = 7.5mA , VEH=3V,  
Time to Output High Level  
(Fig.13)*9  
-
20  
20  
-
-
-
-
-
-
-
-
-
-
tELH  
ns  
CL = 15pF, RL=350Ω  
Enable Propagation Delay  
Time to Output Low Level  
(Fig.13)*10  
IF = 7.5mA , VEL=3V,  
-
tEHL  
ns  
CL = 15pF, RL=350Ω  
IF = 7.5mA , VOH=2.0V,  
RL=350, TA=25°C  
VCM=10Vp-p (Fig.14)  
IF = 7.5mA , VOH=2.0V,  
RL=350, TA=25°C  
VCM=50Vp-p (Fig.14)  
IF = 7.5mA , VOH=2.0V,  
RL=350, TA=25°C  
VCM=400Vp-p (Fig.14)  
IF = 7.5mA , VOH=2.0V,  
RL=350, TA=25°C  
VCM=400Vp-p (Fig.15)  
IF = 0mA , VOL=0.8V,  
RL=350, TA=25°C  
VCM=10Vp-p (Fig.14)  
IF = 0mA , VOL=0.8V,  
RL=350, TA=25°C  
VCM=50Vp-p (Fig.14)  
IF = 0mA , VOL=0.8V,  
RL=350, TA=25°C  
VCM=400Vp-p (Fig.14)  
ELW137  
-
ELW2601  
5,000  
10,000  
20,000  
-
-
Common Mode  
Transient  
CMH  
V/µS  
Immunity at  
Logic High *11  
ELW2611  
-
ELW2611  
ELW137  
-
-
ELW2601  
5,000  
10,000  
-
Common Mode  
Transient  
CML  
V/µS  
Immunity at  
Logic Low *12  
ELW2611  
ELW2611  
-
IF = 7.5mA , VOH=2.0V,  
20,000  
-
-
RL=350, TA=25°C  
VCM=400Vp-p (Fig.15)  
Everlight Electronics Co., Ltd.  
Document No DPC-0000115  
4
http://www.everlight.com  
June 23, 2011  
Rev. 1  
ELW137  
ELW26XX series  
8 PIN DIP WIDE BODY HIGH SPEED  
10MBit/s LOGIC GATE PHOTOCOUPLER  
Typical Performance Curves  
Everlight Electronics Co., Ltd.  
Document No DPC-0000115  
5
http://www.everlight.com  
June 23, 2011  
Rev. 1  
ELW137  
ELW26XX series  
8 PIN DIP WIDE BODY HIGH SPEED  
10MBit/s LOGIC GATE PHOTOCOUPLER  
Everlight Electronics Co., Ltd.  
Document No DPC-0000115  
6
http://www.everlight.com  
June 23, 2011  
Rev. 1  
ELW137  
ELW26XX series  
8 PIN DIP WIDE BODY HIGH SPEED  
10MBit/s LOGIC GATE PHOTOCOUPLER  
I =7.5mA  
F
I =3.75mA  
F
Input  
(I )  
F
t
PHL  
t
PLH  
Output  
(Vo)  
1.5V  
90%  
10%  
Output  
(Vo)  
tf  
tr  
Fig. 12 Test circuit and waveforms for tPHL, tPLH, tr, and tf  
3.0V  
1.5V  
Input  
(V )  
E
t
EHL  
t
ELH  
Output  
(Vo)  
1.5V  
Fig. 13 Test circuit and waveform for tEHLand tELH  
Everlight Electronics Co., Ltd.  
Document No DPC-0000115  
7
http://www.everlight.com  
June 23, 2011  
Rev. 1  
ELW137  
ELW26XX series  
8 PIN DIP WIDE BODY HIGH SPEED  
10MBit/s LOGIC GATE PHOTOCOUPLER  
Peak  
V
CM  
0V  
5V  
Vo  
CM  
H
Switching Pos. (A), I =0  
F
V (Min)  
O
V (Max)  
O
Switching Pos. (B), I =7.5mA  
F
V
CM  
CM  
L
0.5V  
Fig. 14 Test circuit Common mode Transient Immunity  
Fig. 15 Recommended drive circuit for ELW2611 families for high-CMR  
Everlight Electronics Co., Ltd.  
Document No DPC-0000115  
8
http://www.everlight.com  
June 23, 2011  
Rev. 1  
ELW137  
ELW26XX series  
8 PIN DIP WIDE BODY HIGH SPEED  
10MBit/s LOGIC GATE PHOTOCOUPLER  
Notes:  
*3 The VCC supply must be bypassed by a 0.1µF capacitor or larger. This can be either a ceramic or solid  
tantalum capacitor with good high frequency characteristic and should be connected as close as possible to  
the package VCC and GND pins  
*4. Enable Input – No pull up resistor required as the device has an internal pull up resistor.  
Propagation delay is measured from the 3.75mA level on the HIGH to LOW transition of the input  
*5. tPLH  
current pulse to the 1.5 V level on the LOW to HIGH transition of the output voltage pulse.  
Propagation delay is measured from the 3.75mA level on the LOW to HIGH transition of the input  
*6. tPHL  
current pulse to the 1.5 V level on the HIGH to LOW transition of the output voltage pulse.  
*7. tr  
pulse.  
*8. tf  
pulse.  
*9. tELH  
Rise time is measured from the 90% to the 10% levels on the LOW to HIGH transition of the output  
Fall time is measured from the 10% to the 90% levels on the HIGH to LOW transition of the output  
Enable input propagation delay is measured from the 1.5V level on the HIGH to LOW transition of  
the input voltage pulse to the 1.5V level on the LOW to HIGH transition of the output voltage pulse.  
*10. tEHL  
Enable input propagation delay is measured from the 1.5V level on the LOW to HIGH transition of  
the input voltage pulse to the 1.5V level on the HIGH to LOW transition of the output voltage pulse.  
*11 CMH– The maximum tolerable rate of rise of the common mode voltage to ensure the output will remain in  
the HIGH state (i.e., VOUT > 2.0V).  
*12 CML– The maximum tolerable rate of rise of the common mode voltage to ensure the output will remain in  
the LOW output state (i.e., VOUT < 0.8V).  
Order Information  
Part Number  
ELW137Y(Z)-V  
Or  
ELW26XXY(Z)-V  
Note  
XX = 01 or 11 for ELW26 part no.  
Y
Z
V
= Lead form option (S or none)  
= Tape and reel option (TA, TB or none).  
= VDE (optional)  
Option  
None  
Description  
Packing quantity  
45 units per tube  
Standard DIP-8  
S (TA)  
S (TB)  
Surface mount lead form + TA tape & reel option  
Surface mount lead form + TB tape & reel option  
1000 units per reel  
1000 units per reel  
Everlight Electronics Co., Ltd.  
Document No DPC-0000115  
9
http://www.everlight.com  
June 23, 2011  
Rev. 1  
ELW137  
ELW26XX series  
8 PIN DIP WIDE BODY HIGH SPEED  
10MBit/s LOGIC GATE PHOTOCOUPLER  
Package Drawing  
(Dimensions in mm)  
Standard DIP Type  
Option S Type  
Everlight Electronics Co., Ltd.  
Document No DPC-0000115  
10  
http://www.everlight.com  
June 23, 2011  
Rev. 1  
ELW137  
ELW26XX series  
8 PIN DIP WIDE BODY HIGH SPEED  
10MBit/s LOGIC GATE PHOTOCOUPLER  
Recommended pad layout for surface mount leadform  
Device Marking  
EL  
W137  
YWWV  
Notes  
6N137  
Y
denotes Device Number  
denotes 1 digit Year code  
denotes 2 digit Week code  
denotes VDE (optional)  
WW  
V
Everlight Electronics Co., Ltd.  
Document No DPC-0000115  
11  
http://www.everlight.com  
June 23, 2011  
Rev. 1  
ELW137  
ELW26XX series  
8 PIN DIP WIDE BODY HIGH SPEED  
10MBit/s LOGIC GATE PHOTOCOUPLER  
Tape & Reel Packing Specifications  
Option TA  
Option TB  
Direction of feed from reel  
Direction of feed from reel  
Tape dimensions  
Dimension No.  
Dimension(mm)  
A
B
Do  
D1  
E
F
10.4 0.1  
10.0 0.1  
1.5 0.1  
1.5 0.1  
1.75 0.1  
7.5 0.1  
Dimension No.  
Dimension(mm)  
Po  
P1  
P2  
t
W
K
16.0+0.3/  
-0.1  
4.0 0.1  
12.0 0.1  
2.0 0.1  
0.4 0.1  
4.5 0.1  
Everlight Electronics Co., Ltd.  
Document No DPC-0000115  
12  
http://www.everlight.com  
June 23, 2011  
Rev. 1  
                                                                   
                   
                   
                                           
                  
                    
                                                                 
ELW137  
ELW26XX series  
8 PIN DIP WIDE BODY HIGH SPEED  
10MBit/s LOGIC GATE PHOTOCOUPLER  
Solder Reflow Temperature Profile  
260 °C (peak)  
>255 °C ( 30s Max )  
217°  
200°  
1-3 °C/Sec  
60 – 100 Sec  
150°  
60 – 140 Sec  
1-3 °C/Sec  
TIME (S)  
Everlight Electronics Co., Ltd.  
Document No DPC-0000115  
13  
http://www.everlight.com  
June 23, 2011  
Rev. 1  
ELW137  
ELW26XX series  
8 PIN DIP WIDE BODY HIGH SPEED  
10MBit/s LOGIC GATE PHOTOCOUPLER  
DISCLAIMER  
1. Above specification may be changed without notice. EVERLIGHT will reserve authority on material change  
for above specification.  
2. When using this product, please observe the absolute maximum ratings and the instructions for using  
outlined in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting  
from use of the product which does not comply with the absolute maximum ratings and the instructions  
included in these specification sheets.  
3. These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please  
don’t reproduce or cause anyone to reproduce them without EVERLIGHT’s consent.  
Everlight Electronics Co., Ltd.  
Document No DPC-0000115  
14  
http://www.everlight.com  
June 23, 2011  
Rev. 1  

ELW2611S(TB) 相关器件

型号 制造商 描述 价格 文档
ELW2611S(TB)-V EVERLIGHT Logic IC Output Optocoupler 获取价格
ELW2611S-V EVERLIGHT 暂无描述 获取价格
ELW4502 EVERLIGHT 8 PIN DIP WIDE BODY HIGH SPEED 1Mbit/s TRANSISTOR PHOTOCOUPLER 获取价格
ELW4503 EVERLIGHT 8 PIN DIP WIDE BODY HIGH SPEED 获取价格
ELW4503S(TA)-V EVERLIGHT 8 PIN DIP WIDE BODY HIGH SPEED 获取价格
ELW4503S(TB)-V EVERLIGHT 8 PIN DIP WIDE BODY HIGH SPEED 获取价格
ELW4503YZ-V EVERLIGHT 8 PIN DIP WIDE BODY HIGH SPEED 1Mbit/s TRANSISTOR PHOTOCOUPLER 获取价格
ELWCF19GF PANASONIC General Purpose Inductor, 0.02uH, 20%, 1 Element, SMD 获取价格
ELWCF25GF PANASONIC General Purpose Inductor, 0.011uH, 20%, 1 Element, SMD 获取价格
ELWCF900F PANASONIC General Purpose Inductor, 0.088uH, 20%, 1 Element, SMD 获取价格

ELW2611S(TB) 相关文章

  • 宽带隙半导体:军事应用中的卓越之选
    2025-05-22
    4
  • 电路设计中瞬态过压保护:三大疑问全解读
    2025-05-22
    6
  • 小米豪掷造芯,YU7 能否重现华为汽车的辉煌时刻?
    2025-05-22
    5
  • 千兆级集成电路封装:重塑全球半导体供应链格局
    2025-05-21
    19
  • Hi,有什么可以帮您? 在线客服 或 微信扫码咨询