首页 > WRPPB-A1Q7NN-P

WRPPB-A1Q7NN-P

更新时间：2025-07-10 22:28:53
品牌：MSYSTEM
描述：Dual Output Plug-in Signal Conditioners W-UNIT

PDF下载

中文翻译

免费 PCB/SMT

WRPPB-A1Q7NN-P 概述

Dual Output Plug-in Signal Conditioners W-UNIT

WRPPB-A1Q7NN-P 数据手册

通过下载WRPPB-A1Q7NN-P数据手册来全面了解它。这个PDF文档包含了所有必要的细节，如产品概述、功能特性、引脚定义、引脚排列图等信息。

PDF下载
MODEL: WRPPB  
Dual Output Plug-in Signal Conditioners W-UNIT  
[2] OUTPUT 1  
A: Open collector  
K5: 3.3 V pulse, output impedance 50 Ω  
K7: 3.3 V pulse, output impedance 75 Ω  
M5: 5 V pulse, output impedance 50 Ω  
M7: 5 V pulse, output impedance 75 Ω  
Q7: 10 V pulse, output impedance 50 Ω  
N: 12 V pulse, load resistance 600 Ω  
J: RS-422 line driver pulse  
ENCODER SIGNAL DISTRIBUTOR  
(rotary encoder use, BNC connection)  
Functions & Features  
• Isolating two phase pulse input signals from a rotary  
encoder and distributing them to two outputs (input  
frequency = output frequency)  
• Various outputs (open collector, voltage pulse, RS-422 line  
driver pulse)  
• Can be used as a pulse isolator of two different I/O specs  
• Converting RS-422 line driver pulse into an open collector  
pulse  
[3] OUTPUT 2  
Same range availability as Output 1  
(Q7 not selectable)  
• Maximum frequency of 1 MHz  
• BNC connector  
[4] OUTPUT LOGIC (both Input 1 & 2)  
N: The same as the input  
• Characteristic impedance 50Ω and 75Ω available  
R: Inverted  
(
)
50 1.97  
[5] POWER INPUT  
AC Power  
(
)
80 3.15  
M2: 100 – 240 V AC (Operational voltage range 85 – 264 V,  
47 – 66 Hz)  
DC Power  
R: 24 V DC  
(
)
123 4.84  
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)  
P: 110 V DC  
mm (inch)  
(Operational voltage range 85 – 150 V, ripple 10 %p-p max.)  
MODEL: WRPPB–[1][2][3][4]-[5][6]  
[6] OPTIONS  
blank: none  
ORDERING INFORMATION  
• Code number: WRPPB-[1][2][3][4]-[5][6]  
Specify a code from below for each of [1] through [6].  
(e.g. WRPPB-A1K5K5N-M2/Q)  
/Q: With options (specify the specification)  
SPECIFICATIONS OF OPTION: Q (multiple selections)  
COATING (For the detail, refer to M-System's web site.)  
/C01: Silicone coating  
• Specify the specification for option code /Q  
(e.g. /C01/S01)  
/C02: Polyurethane coating  
/C03: Rubber coating  
[1] INPUT  
A1: Dry contact  
TERMINAL SCREW MATERIAL  
/S01: Stainless steel  
K: 3.3 V pulse, input impedance approx. 8 kΩ 100 pF  
K5: 3.3 V pulse, input impedance 50 Ω  
K7: 3.3 V pulse, input impedance 75 Ω  
C: 5 V pulse, input impedance approx. 14 kΩ 100 pF  
C5: 5 V pulse, input impedance 50 Ω  
C7: 5 V pulse, input impedance 75 Ω  
D: 12 V/24 V pulse  
GENERAL SPECIFICATIONS  
Construction: Plug-in  
Connection  
I/O: BNC connectors  
(Recommended connector manufacturer: Hirose)  
Power input: M3.5 screw terminals  
Screw terminal: Chromated steel (standard) or stainless  
steel  
J: RS-422 line driver pulse  
Housing material: Flame-resistant resin (black)  
WRPPB SPECIFICATIONS  
ES-2223 Rev.3 Page 1/6  
http://www.m-system.co.jp/  
MODEL: WRPPB  
Isolation: Input to output 1 to output 2 to power  
Input pulse sensing: DC coupled  
OUTPUT SPECIFICATIONS  
■ Open collector  
Max. frequency: 100 kHz  
Rating: 50 V DC @ 100 mA  
INPUT SPECIFICATIONS  
■ Dry Contact  
Saturation voltage: 0.12 V DC  
■ Voltage Pulse (open voltage):  
Rating (3.3, 5, 10 or 12 V) ±20 %  
Max. frequency ; Load resistance (the lower value of either  
this or the maximum frequency of the input signal)  
3.3 V 1 MHz / Output code K5: 50 Ω, K7: 75Ω  
5 V 500 kHz / Output code M5: 50 Ω, M7: 75Ω  
10 V 200 kHz / 75Ω  
Max. frequency: 100 kHz  
Min. pulse width: ≥ 5 μs  
Input requirements  
Sensing: 5 V DC / 10 mA  
Detecting level:  
OFF: ≥ 3.0 V / ≥ 750 Ω  
ON: ≤ 2.0 V / ≤ 333 Ω  
12 V 100 kHz / 600 Ω  
Sensing voltage/current shows the excitation supply to the  
input terminal and the current value at the time of  
shortcircuit.  
(≥ 6 V @ 600 Ω load)  
Low level: ≤ 0.5 V  
■ RS-422 Line Driver Pulse: Conforms to RS-422  
Max. frequency: 1 MHz  
Detecting level shows the threshold used to determine ON  
or OFF status of the pulses and the resistance values of the  
dry contact of that time.  
Output current: ±20 mA  
■ Voltage Pulse  
Waveform: Square or sine  
INSTALLATION  
Power Consumption  
•3.3 V Pulse  
Max. frequency: 1 MHz  
•AC:  
Min. pulse width: ≥ 0.5 μs  
Approx. 4 VA at 100 V  
Input impedance: Approx. 8 kΩ 100 pF  
Max. voltage between terminals (pulse): -10 – +15 V  
Max. voltage between terminals (DC): -5 – +10 V DC  
Approx. 5 VA at 200 V  
Approx. 6 VA at 240 V  
•DC: Approx. 3 W  
Detecting level: V  
H
≥ 2.0 V, V ≤ 1.3 V  
L
Operating temperature: -5 to +55°C (23 to 131°F)  
Operating humidity: 30 to 90 %RH (non-condensing)  
Mounting: Surface or DIN rail  
Weight: 260 g (0.57 lb)  
Input impedance: Approx. 50 Ω, 75 Ω  
Max. voltage between terminals (pulse): -7 – +7.5 V  
Max. voltage between terminals (DC): -5 – +10 V DC  
Detecting level: V  
H
≥ 1.5 V, V ≤ 0.75 V  
L
•5 V Pulse  
PERFORMANCE  
Response time  
Max. frequency: 500 kHz  
Min. pulse width: ≥ 1 μs  
•Lower value of I/O max. frequency is 1 MHz:  
0.15 - 0.5 μsec.  
Input impedance: Approx. 14 kΩ 100 pF  
Max. voltage between terminals (pulse): -10 – +15 V  
Max. voltage between terminals (DC): -5 – +10 V DC  
•Lower value of I/O max. frequency is 500 kHz:  
0.2 - 1.2μs  
Detecting level: V  
H
≥ 3.0 V, V ≤ 2.0 V  
L
•Lower value of I/O max. frequency is less than 500 kHz:  
0.2 - 2 μsec.  
Input impedance: Approx. 50 Ω, 75 Ω  
Max. voltage between terminals (pulse): -7 – +10 V  
Max. voltage between terminals (DC): -5 – +7.5 V DC  
Insulation resistance: ≥ 100 MΩ with 500 V DC  
Dielectric strength: 500 V AC @ 1 minute (input to output 1  
to output 2)  
Detecting level: V  
H
≥ 2.4 V, V ≤ 1.2 V  
L
•12 V, 24 V Pulse  
2000 V AC @ 1 minute (input or output 1 or output 2 to  
power to ground)  
Max. frequency: 100 kHz  
Min. pulse width: ≥ 5 μs  
Input impedance: Approx. 20 kΩ  
Max. voltage between terminals (pulse): -30 – +50 V  
Max. voltage between terminals (DC): -30 – +50 V DC  
STANDARDS & APPROVALS  
EU conformity:  
Detecting level: V  
H
≥ 7.0 V, V ≤ 5.0 V  
L
EMC Directive  
■ RS-422 Line Driver Pulse  
Maximum frequency: 1 MHz  
EMI EN 61000-6-4  
EMS EN 61000-6-2  
Receiver: Conforms to RS-422  
Low Voltage Directive  
WRPPB SPECIFICATIONS  
ES-2223 Rev.3 Page 2/6  
http://www.m-system.co.jp/  
MODEL: WRPPB  
EN 61010-1  
Measurement Category II  
Pollution Degree 2  
Input or output 1 or output 2 to power input:  
Reinforced insulation (300 V)  
Input to output 1 to output 2: Basic insulation (300 V)  
RoHS Directive  
EN 50581  
EXTERNAL VIEW  
Input Phase A  
Input Phase B  
Input Monitor LED  
Phase B (Red)  
INPUT  
IN A  
IN B  
MONITOR  
Input Monitor LED  
Phase A (Green)  
B
A
Output 1 Phase B  
Output 2 Phase B  
Output 1 Phase A  
Output 2 Phase A  
OUT 1A  
OUT 1B  
OUT 2A  
OUT 2B  
OUTPUT LOGIC  
Applicable for both Output 1 and 2.  
Voltage pulse  
Input  
Dry contact  
RS-422 line driver pulse  
H
OFF  
Output  
L
ON  
H
H
Voltage pulse  
Non-inverted  
L
L
or  
RS-422 line  
H
H
driver pulse  
Inverted  
L
L
OFF  
OFF  
Non-inverted  
Inverted  
ON  
ON  
Open collector  
OFF  
OFF  
ON  
ON  
WRPPB SPECIFICATIONS  
ES-2223 Rev.3 Page 3/6  
http://www.m-system.co.jp/  
MODEL: WRPPB  
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)  
CLAMP  
(top & bottom)  
(
7.8 0.31  
)
(
20 0.79  
)
DIN RAIL  
35mm wide  
6
5
4
3
2–4.5 (.18) dia.  
MTG HOLE  
15 (.59) deep  
7
8
1
2
8–M3.5  
SCREW  
16 (.63)  
(
103 4.06  
)
(
40 1.57  
)
(
50 1.97  
)
(
123 4.84  
)
[
(
3.3 .13  
)]  
(
50 1.97  
)
11  
0.43  
(
)
• When mounting, no extra space is needed between units.  
WRPPB SPECIFICATIONS  
ES-2223 Rev.3 Page 4/6  
http://www.m-system.co.jp/  
MODEL: WRPPB  
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM  
Output Circuit  
Phase A  
+
Isolation  
PHASE A  
−
Input  
Circuit  
+
PHASE A  
−
OUTPUT 1  
+
Output Circuit  
Phase B  
PHASE B  
−
INPUT  
Input  
Circuit  
+
PHASE B  
−
Output Circuit  
Phase A  
+
PHASE A  
−
OUTPUT 2  
+
1
2
3
4
5
6
Output Circuit  
Phase B  
PHASE B  
−
7
8
U (+)  
POWER  
V (−)  
Base Socket  
Input Connection Examples  
• Dry Contact Input  
Output Connection Examples  
• Open Collector Output  
• Voltage Pulse Output  
• RS-422 Line Driver Pulse Output  
PHASE A  
PHASE A  
PHASE B  
PHASE A  
PHASE B  
PHASE A  
PHASE A  
+
–
PHASE B  
PHASE B  
PHASE A  
PHASE B  
PHASE B  
+
–
5V  
PHASE A  
500Ω  
+
–
PHASE B  
• Voltage Pulse Input  
+
PHASE A  
–
PHASE B  
• RS-422 Line Driver Pulse Input  
PHASE A  
PHASE A  
RS-422  
Receiver  
250Ω  
PHASE A  
PHASE B  
PHASE B  
PHASE B  
RS-422  
250Ω  
Receiver  
WRPPB SPECIFICATIONS  
ES-2223 Rev.3 Page 5/6  
http://www.m-system.co.jp/  
MODEL: WRPPB  
Specifications are subject to change without notice.  
WRPPB SPECIFICATIONS  
ES-2223 Rev.3 Page 6/6  
http://www.m-system.co.jp/  

WRPPB-A1Q7NN-P 相关器件

型号 制造商 描述 价格 文档
WRPPB-A1Q7NN-R MSYSTEM Dual Output Plug-in Signal Conditioners W-UNIT 获取价格
WRPPB-A1Q7NN-R/Q MSYSTEM Dual Output Plug-in Signal Conditioners W-UNIT 获取价格
WRPPB-A1Q7NR-M2 MSYSTEM Dual Output Plug-in Signal Conditioners W-UNIT 获取价格
WRPPB-A1Q7NR-M2/Q MSYSTEM Dual Output Plug-in Signal Conditioners W-UNIT 获取价格
WRPPB-A1Q7NR-P MSYSTEM Dual Output Plug-in Signal Conditioners W-UNIT 获取价格
WRPPB-A1Q7NR-R MSYSTEM Dual Output Plug-in Signal Conditioners W-UNIT 获取价格
WRPPB-A1Q7NR-R/Q MSYSTEM Dual Output Plug-in Signal Conditioners W-UNIT 获取价格
WRPPB-JAAN-M2 MSYSTEM Dual Output Plug-in Signal Conditioners W-UNIT 获取价格
WRPPB-JAAN-M2/Q MSYSTEM Dual Output Plug-in Signal Conditioners W-UNIT 获取价格
WRPPB-JAAN-P MSYSTEM Dual Output Plug-in Signal Conditioners W-UNIT 获取价格

WRPPB-A1Q7NN-P 相关文章

  • 小米 AI 眼镜技术亮点：双芯架构助力智能穿戴跨越发展
    2025-07-11
    33
  • AI 芯片风云：台积电能否超越英伟达成新霸主？
    2025-07-11
    25
  • 锁存型霍尔 IC：原理、应用大揭秘
    2025-07-11
    25
  • HBM 角逐：定制化、混合键合等技术成竞争关键
    2025-07-11
    22

    • 热门型号

  • 1N5930
  • 1N5942B
  • 1N4001
  • MBR3050CT
  • RTA02-8D
  • 4116T
  • 5KP43A/4
  • 1N5260A
  • MC79L05
  • BZX85C30
  • 9510-G
  • W2PE-54WZ-P
  • 1N6063
  • 2SA673
  • 20IMX35
    • Hi,有什么可以帮您？ 在线客服 或 微信扫码咨询
  • 概述
  • 数据手册
    • 2025 ICPDF网 联系我们和版权申明:QQ 272164286