REVISION T
SFSDX-XX-XXX-XX-XX.XX-XX-XXX
(No OF POS x .050[1.27])
+ .015[0.38] REF
-NXX OPTION (END 2)
(ONLY AVAILABLE WITH -D, -DL, -DR)
-NUS: NOTCH UP, STRAIGHT
(PIN 1 TO PIN N-1)
FEP CABLE OPTION
-T: FEP
(LEAVE BLANK FOR STANDARD PVC INSULATION)
-NDS: NOTCH DOWN, STRAIGHT
(PIN 1 TO PIN 2)
No OF POSITIONS
-05, -07, -10, -15, -20, -25,
N-1 (SEE TABLE 2)
01
-NUX: NOTCH UP, CROSSED
(PIN 1 TO PIN N)
-30 -35 -40, -45, & -50 (PER ROW)
AVAILABLE AS STANDARD
-02 THRU -50 AVAILABLE AS ASO
C
L
-NDX: NOTCH DOWN, CROSSED
(PIN 1 TO PIN 1)
.250 6.35
REF
WIRE GAUGE (AWG)
.120 3.05 REF
.145 3.68 REF
-28, -30
END OPTION
COLOR CODE:
(END OPTION COMBINATIONS NOT AVAILABLE)
-S: SINGLE END
LEAVE BLANK FOR ALL BLACK WIRE
C: COLOR CODED WIRE, SEE COLOR
SEQUENCE TABLE, SHEET 3
-D: DOUBLE END
02
(MUST CHOOSE FROM -NXX OPTIONS)
-SL: SINGLE ENDED WITH FRICTION LOCK
(SEE SHEET 2, FIG. 3) (ONLY AVAILABLE
ON -10 THRU -30 POSITION)
N (SEE TABLE 2)
(NOT AVAILABLE WITH FEP OPTION)
.080 2.03 REF
FIG. 1
PLATING SPECIFICATION
.050 1.27
REF
-S: SINGLE END
(SFSD-10-28-XX-XX.XX-S SHOWN)
ISDF-XX-D
-H: HEAVY GOLD
-DL: DOUBLE ENDED WITH FRICTION LOCK
(SEE SHEET 2, FIG. 4) (ONLY AVAILABLE
ON -10 THRU -30 POSITION)
-G: LIGHT GOLD
-GF: FLASH GOLD
(SEE TABLE 4, SHEET 3)
(MUST CHOOSE FROM -NXX OPTIONS)
-SR: SINGLE ENDED WITH RETENTION LATCH
(SEE SHEET 4, FIG. 5)(USE SUB-IM-LTC-07-01-N)
(ONLY AVAILABLE ON -05 THRU -30 POS)
-DR: DOUBLE ENDED WITH RETENTION LATCH
(SEE SHEET 4, FIG. 6)(USE SUB-IM-LTC-07-01-N)
(ONLY AVAILABLE ON -05 THRU -30 POS)
(MUST CHOOSE FROM -NXX OPTIONS)
.050 1.27 REF
"A"
ASSEMBLED LENGTH
SPECIFY IN INCHES
(SINGLE END: 03.00 INCH [76.2mm] MINIMUM,
DOUBLE END: 03.25 INCH [82.6mm] MINIMUM)
.440 11.18
REF
.249 6.32
REF
C1
ASSEMBLED LENGTH:
(SEE NOTE 8)
C2
ASSEMBLED LENGTH:
XX.XX .125[3.18]
DWLX-08-XXX-X-XX.XX-XX
SECTION "A"-"A"
"A"
NOTES:
C
1.
REPRESENTS A CRITICAL DIMENSION.
FIG. 2
2. MINIMUM PULLOUT FORCE: 3.0 LBS [13.3 N].
3. CONTACT MUST BE INSERTED UNTIL
-D: DOUBLE END
C3
C4
(SFSD-10-28-XX-XX.XX-D-NUS SHOWN)
RETENTION FEATURE LOCKS INTO PLACE.
4. ALL FINISHED GOODS ARE TO BE ELECTICAL
TESTED INCLUDING HI-POT TEST AT 1000 VOLTS DC.
AFTER FINAL ELECTRICALTEST, LABEL EACH ASSEMBLY
WITH 1 LABEL-ET.
(SAME AS FIG. 1, UNLESS OTHERWISE STATED)
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
5. TINNED COPPER WIRE IS RoHS COMPLIANT.
6. PARTS TO BE LAYER PACKAGED.
DECIMALS
ANGLES
.XX: .01 [.3]
2
520 PARK EAST BLVD, NEW ALBANY, IN 47150
.XXX: .005 [.13]
7. END OF DISCRETE WIRE MUST BE IN THE RANGE AFTER CRIMP.
8. FOR LENGTHS LESS THAN 12 in, TOLERANCE SHALL BE +/-.125.
FOR OTHER LENGTHS, TOLERANCE SHALL BE +/-2%.
9. NOTE DELETED.
PHONE: 812-944-6733
FAX: 812-948-5047
code: 55322
.XXXX: .0020 [.051]
e-Mail: info@SAMTEC.com
SHEET SCALE: 2:1
DO NOT SCALE DRAWING
DESCRIPTION:
MATERIAL:
.050[1.27] SOCKET DISCRETE CABLE ASSEMBLY
DWG. NO.
INSULATOR: LCP, COLOR: BLACK
CONTACT: BeCu
CABLE INSULATION: SEE CALLOUT
WIRE: TINNED COPPER
T
C10
10. FOR CRIMP DIMENSIONS SEE DWL-08-XXX-X-XX.XX-XX FOR PVC APPLICATIONS
AND DWLT-08-XX-X-XX.XX-XX-XX FOR FEP APPLICATIONS.
11. 3LB MIN WIRE CRIMP STRENGTH FOR -30 AWG AND
SFSDX-XX-XXX-XX-XX.XX-XX-XXX
4.5LB MIN WIRE CRIMP STRENGTH FOR -28 AWG.
SHEET 1 OF 3
F:\DWG\MISC\MKTG\SFSDX-XX-XXX-XX-XX.XX-XX-XXX-MKT.SLDDRW
BY:
BRATCHER 5/5/2005
MRAM 强势来袭，引领 MCU 存储新变革
HBF 引领存储变革，NAND 有望再现 HBM 辉煌
Wi-Fi 8 要来了！详细技术亮点与应用前景
半导体芯片制造全流程工艺技术的详细解读
概述
规格参数
数据手册
