RAT30XLSE15RC100K

更新时间:2025-11-04 07:50:14
品牌:TOCOS
描述:30mm Diameter, Single-Turn,Wirewound Industrial Panel Controls

RAT30XLSE15RC100K 概述

30mm Diameter, Single-Turn,Wirewound Industrial Panel Controls 直径30mm ,单圈,线绕工业面板控制

RAT30XLSE15RC100K 数据手册

通过下载RAT30XLSE15RC100K数据手册来全面了解它。这个PDF文档包含了所有必要的细节,如产品概述、功能特性、引脚定义、引脚排列图等信息。

PDF下载
®
TOCOS  
RA30Series  
P A N E L C O N T R O L S  
30mm Diameter, Single-Turn, Wirewound Industrial Panel Controls  
RA30YME  
RA30YD  
RA30Y  
Features  
30mm diameter, single-turn industrial panel controls  
Wirewound element Linear or audio tapers  
Single, tandem and triple units, single shaft; dual unit, dual shaft  
SPST or SPDT switch with 1A or 3A rating  
Temperature range of 10C or30C, up to 100C  
Shaft lock and center tap models  
Metal shaft and bushing  
Panel mount only  
6mm diameter shafts in slot, flat or round end styles Standard 15mm or 20mm shaft length  
Specifications  
Electrical  
Environmental  
Standard Resistance Range . . . . . . . . . . . B = 5to 20kΩ  
A,C = 100to 5kΩ  
Temperature Range . . . . . . . . . . . . . . Y= 10C to 100C  
or X = 30C to 100C  
Resistance Tolerance . . . . . . . . . . . . . . . . . 10% standard  
Temperature Characteristics . . . . . . . . . . . 85C, 5 hours  
(
5%, 2% or 1% special order)  
without load  
)
T/R  
5%  
!
End Resistance . . . . . . . . . . . . . . . . . . R 500= 1max.  
0
R
500= 0.2% max.  
Low Temperature Exposure . . . . . . . 10C (Y),30C (X)  
1 hour without load  
Resistance Taper . . . . B = linear; A = CW audio (logarithm);  
)
T/R  
3%  
C = CCW audio (logarithm)  
Power Rating . . . B = 2.5 watts; A,C = 1.25 watts, at 40C  
Load Life . . . . . . . . . . . . 40C, 1,000 hours with rated load  
)
T/R  
3%  
Insulation Resistance . . . . . . .100Mminimum at 500VDC  
Dielectric Strength . . . . . . . . . . . . . . . . . . 500VAC, 1 minute  
Theoretical Resolution  
Moisture and Load Life . . . . . . . . . . . . 40C, 90-95%RH,  
500 hours with 1/10 rated load  
)
T/R  
5%  
Resistance () Resolution (%) Resistance () Resolution (%)  
Vibration . . . . . . . . . . . . . . . . . . .10-55Hz, 1.5mm amplitude,  
5
10  
1.62  
0.81  
0.67  
0.45  
0.44  
0.32  
500  
1,000  
2,000  
0.23  
0.19  
0.15  
0.14  
0.12  
0.10  
2 directions, 2 hours each  
)
1%  
T/R  
20  
50  
5,000  
Soldering Heat Resistance . . . . . . . . . 350C, 3.5 seconds;  
100  
200  
10,000  
20,000  
)
T/R  
2%  
Rotational Life . . . . 15,000 cycles (500 cycles for shaft lock  
Mechanical  
models only) with 1/2 rated load  
)
T/R  
3%  
Mechanical Travel . . . . . . . . . . . . . . . . . . . . . . . . . . 3005ꢂ  
Standard Rotary Switches  
Switch Rating . . . . . . . . . .110VAC, 1A or 3A, SPDT or SPST  
Contact Resistance . . . . . . . . . . . . . . . . . . . . . . 0.05max.  
Shaft Torque  
Single Unit . . . . . 70.1 to 306 gf cm (0.972 to 4.242 oz in)  
Tandem Unit . . . . . . 70 to 701 gf cm (0.97 to 9.718 oz in)  
Other Units . . . . . . . 70 to 450 gf cm (0.97 to 6.238 oz in)  
Operating Torque . . . . . . . . 1,500 gf cm (20.79 oz in) max.  
Operating Life . . . . . . . . . . . . . . . 10,000 cycles without load  
R = Total Resistance Value; T/R = Total Resistance Change  
Stop Strength . . . . . . . . . . . .10.2 kgf cm (141.4 oz in) max.  
Mounting Nut Torque . . . . . .15 kgf cm (207.94 oz in) max.  
Solderability . . . . . . . . . . . . . . . . . . . . . . . 235C, 3 seconds  
Marking . . . . . . . . . . Taper, resistance, resistance tolerance,  
terminal identification, date code  
TOCOSAMERICA,INC.  
63  
1177 East Tower Road, Schaumburg, IL 60173 Tel: 847-884-6664 Fax: 847-884-6665 E-mail: sales tocos.com www.tocos.com  
@
Dimensions  
RA30 Series  
Unit: mm  
RA30Y & RA30X  
Panel Mount, Single Unit, Single Shaft  
Right Angle Ear-Lug Terminals  
Recommended  
Panel Mounting Holes  
RA30YL & RA30XL  
Panel Mount, Single Unit, Single Shaft with Shaft Lock  
Right Angle Ear-Lug Terminals  
Recommended  
Panel Mounting Holes  
RA30YME, RA30YMF, RA30YSE, RA30YSF  
RA30XME, RA30XMF, RA30XSE, RA30XSF  
Panel Mount, Single Unit with Switch, Single Shaft  
Right Angle Ear-Lug Terminals, Rear Exit Lug Terminals for 1A or 3A SPST or SPDT Switch  
Recommended  
Panel Mounting Holes  
TOCOSAMERICA,INC.  
64  
1177 East Tower Road, Schaumburg, IL 60173 Tel: 847-884-6664 Fax: 847-884-6665 E-mail: sales tocos.com www.tocos.com  
@
Dimensions  
RA30 Series  
Unit: mm  
RAT30Y  
Panel Mount, Single Unit with Center Tap, Single Shaft  
Right Angle Ear-Lug Terminals, Tap Lug Terminal 105from Terminal #1  
Recommended  
Panel Mounting Holes  
RA30YG  
Panel Mount, Ganged Tandem Unit, Single Shaft  
Right Angle Ear-Lug Terminals on Each Unit  
Recommended  
Panel Mounting Holes  
RA30YGL  
Panel Mount, Ganged Tandem Unit, Single Shaft with Shaft Lock  
Right Angle Ear-Lug Terminals on Each Unit  
Recommended  
Panel Mounting Holes  
TOCOSAMERICA,INC.  
65  
1177 East Tower Road, Schaumburg, IL 60173 Tel: 847-884-6664 Fax: 847-884-6665 E-mail: sales tocos.com www.tocos.com  
@
Dimensions  
RA30 Series  
Unit: mm  
RAT30YG  
Panel Mount, Ganged Tandem Unit with Center Tap, Single Shaft  
Right Angle Ear-Lug Terminals, Tap Lug Terminal 105from Terminal #1  
Recommended  
Panel Mounting Holes  
RA30YT  
Panel Mount, Triple Unit, Single Shaft  
Right Angle Ear-Lug Terminals on Each Unit  
Recommended  
Panel Mounting Holes  
RA30YD  
Panel Mount, Dual Unit, Dual Concentric Shaft  
Right Angle Ear-Lug Terminals on Each Unit  
Recommended  
Panel Mounting Holes  
TOCOSAMERICA,INC.  
66  
1177 East Tower Road, Schaumburg, IL 60173 Tel: 847-884-6664 Fax: 847-884-6665 E-mail: sales tocos.com www.tocos.com  
@
Part Numbering System  
RA30 Series  
RA T 30 Y L ME 20 S B 102 K  
NOTE: FMS = From Mounting Surface  
Resistance Tolerance: K = 10% (standard).  
J = 5%; G = 2%; or F = 1% (special order).  
Resistance Code: Expressed in ohms. A three digit code where the first  
two digits are significant figures, and the third digit indicates the number  
of zeros that follow these figures. R indicates decimal point for resistance  
less than 10(i.e., 5R0 = 5;100 = 10;101 = 100;102 = 1,000;  
103 = 10,000). See table for standard resistance values.  
For Single Unit: Specify taper and resistance code as shown.  
For Ganged Tandem Unit or Dual Unit:  
Specify a taper code and resistance code for each unit starting with  
the front unit followed by the rear unit. If both units have the same taper  
and resistance codes, add X2” suffix per example below.  
Examples: B102A503 or if both units are the same: B102X2  
For Triple Unit:  
Specify a taper code and resistance code for each unit starting with  
the front unit followed by the middle and rear units. If all units have the  
same taper and resistance codes, add X3” suffix per example below.  
Examples: B102A503B104 or if all units are the same: B102X3  
Resistance Taper: B = Linear; A = CW Audio (logarithm);  
C = CCW Audio (logarithm).  
Shaft End Style: S = Slotted; F = Flatted; R = Round.  
For Single Shaft:  
Specify the shaft length (FMS) and shaft end style as shown.  
For Dual Concentric Shaft:  
Specify the shaft length (FMS) and shaft end style for the inner shaft  
followed by the shaft length (FMS) and shaft end style for the outer  
shaft. Use a dash (-) to separate the code groups for the inner and  
outer shaft specifications. Example: 30R-20R  
Standard Shaft Length: 15 = 15mm FMS; 20 = 20mm FMS.  
Up to 50mm shaft length available (special order).  
Switch Type: ME = SPDT,110VAC, 1A, Rear Exit Lug Terminals.  
MF = SPDT,110VAC, 3A, Rear Exit Lug Terminals.  
SE = SPST, 110VAC, 1A, Rear Exit Lug Terminals.  
SF = SPST, 110VAC, 3A, Rear Exit Lug Terminals.  
Blank = No Switch.  
Style: Blank = Panel Mount, Single Unit, Single Shaft, Right Angle Ear-Lug  
Terminals.  
L
= Panel Mount, Single Unit, Single Shaft with Shaft Lock,  
Right Angle Ear-Lug Terminals.  
G
= Panel Mount, Ganged Tandem Unit, Single Shaft, Right Angle  
Ear-Lug Terminals on Each Unit.  
GL = Panel Mount, Ganged Tandem Unit, Single Shaft with Shaft  
Lock, Right Angle Ear-Lug Terminals on Each Unit.  
= Panel Mount, Triple Unit, Single Shaft, Right Angle Ear-Lug  
Terminals on Each Unit.  
T
D
= Panel Mount, Dual Unit, Dual Concentric Shaft, Right Angle  
Ear-Lug Terminals on Each Unit.  
Operating Temperature Range: Y = 10C to 100C.  
X = 30C to 100C.  
Size: 30 = 30mm Diameter.  
Center Tap: T = With Tap; Blank = Without Tap.  
TOCOS Series Name: RA = Wirewound Element.  
Standard Resistance Values and Part Numbering Codes  
Standard Nominal Total Resistance Values and Part Numbering Codes  
Resistance ()  
Code  
Resistance ()  
Code  
Resistance ()  
Code  
Resistance ()  
Code  
05  
10  
20  
50  
5R0  
100  
200  
500  
100  
200  
500  
101  
201  
501  
1,000  
2,000  
5,000  
102  
202  
502  
10,000  
20,000  
103  
203  
Refer to Shaft End Styles Specifications and Hardware Specifications for details and availability.  
For additional information, refer to Guidelines and Precautions for Using Panel Controls.  
TOCOSAMERICA,INC.  
67  
1177 East Tower Road, Schaumburg, IL 60173 Tel: 847-884-6664 Fax: 847-884-6665 E-mail: sales tocos.com www.tocos.com  
@

RAT30XLSE15RC100K 相关器件

型号 制造商 描述 价格 文档
RAT30XLSE15RC101K TOCOS 30mm Diameter, Single-Turn,Wirewound Industrial Panel Controls 获取价格
RAT30XLSE15RC102K TOCOS 30mm Diameter, Single-Turn,Wirewound Industrial Panel Controls 获取价格
RAT30XLSE15SA100K TOCOS 30mm Diameter, Single-Turn,Wirewound Industrial Panel Controls 获取价格
RAT30XLSE15SA101K TOCOS 30mm Diameter, Single-Turn,Wirewound Industrial Panel Controls 获取价格
RAT30XLSE15SA102K TOCOS 30mm Diameter, Single-Turn,Wirewound Industrial Panel Controls 获取价格
RAT30XLSE15SA103K TOCOS 30mm Diameter, Single-Turn,Wirewound Industrial Panel Controls 获取价格
RAT30XLSE15SB100K TOCOS 30mm Diameter, Single-Turn,Wirewound Industrial Panel Controls 获取价格
RAT30XLSE15SB101K TOCOS 30mm Diameter, Single-Turn,Wirewound Industrial Panel Controls 获取价格
RAT30XLSE15SB102K TOCOS 30mm Diameter, Single-Turn,Wirewound Industrial Panel Controls 获取价格
RAT30XLSE15SB103K TOCOS 30mm Diameter, Single-Turn,Wirewound Industrial Panel Controls 获取价格
Hi,有什么可以帮您? 在线客服 或 微信扫码咨询