转到网站首页
转为中文步骤：
1、请用电脑端360浏览器打开本页地址，如您电脑未安装360浏览器，请点这里下载;
2、点击360浏览器右上角的翻译插件，如右图红圈中所示:
3、点击所弹出窗口里的右下角的按钮 “翻译当前网页”;
4、弹窗提示翻译完毕后关闭弹窗即可；
Features  
• 8-bit Multiplexed Addresses/Outputs  
• Fast Read Access Time – 70 ns  
• Dual Voltage Range Operation  
– Low-voltage Power Supply Range, 3.0V to 3.6V, or  
– Standard 5V ꢀ0% Supply Range  
• Pin Compatible with Standard AT27C520  
• Low-power CMOS Operation  
– 20 µA Max Standby for ALE = VIH and VCC = 3.6V  
– 29 mW Max Active at 5 MHz for VCC = 3.6V  
• JEDEC Standard Packages  
5ꢀ2K (64K x 8)  
Multiplexed  
Addresses/  
Outputs  
– 20-lead TSSOP  
– 20-lead SOIC  
• High-reliability CMOS Technology  
– 2,000V ESD Protection  
– 200 mA Latch-up Immunity  
• Rapid Programming Algorithm – 50 µs/Byte (Typical)  
• CMOS- and TTL-compatible Inputs and Outputs  
– JEDEC Standard for LVTTL  
Low-voltage  
OTP EPROM  
• Integrated Product Identification Code  
• Industrial Temperature Range  
• Green (Pb/Halide-free) Packaging Option  
AT27LV520  
ꢀ. Description  
The AT27LV520 is a low-power, high-performance, 524,288-bit one-time programma-  
ble read-only memory (OTP EPROM) organized 64K by eight bits. It incorporates  
latches for the eight lower order address bits to multiplex with the eight data bits. This  
minimizes system chip count, reduces cost, and simplifies the design of multiplexed  
bus systems. It requires only one power supply in the range of 3.0V to 3.6V for normal  
read mode operation, making it ideal for fast, portable systems using battery power.  
Any byte can be accessed in less than 70 ns.  
The AT27LV520 is available in 20-lead TSSOP and 20-lead SOIC, one-time program-  
mable (OTP) plastic packages.  
Atmel’s innovative design techniques provide fast speeds that rival 5V parts while  
keeping the low power consumption of a 3.3V supply. At VCC = 3.0V, any byte can be  
accessed in less than 70 ns. With a typical power dissipation of only 18 mW at 5 MHz  
and VCC = 3.3V, the AT27LV520 consumes less than one fifth the power of a standard  
5V EPROM. Standby mode is achieved by asserting ALE high. Standby mode supply  
current is typically less than 1 µA at 3.3V.  
The AT27LV520 operating with VCC at 3.0V produces TTL level outputs that are com-  
patible with standard TTL logic devices operating at VCC = 5.0V. The device is also  
capable of standard 5-volt operation making it ideally suited for dual supply range  
systems or card products that are pluggable in both 3-volt and 5-volt hosts.  
0911F–EPROM–10/05  
Atmel’s AT27LV520 has additional features to ensure high quality and efficient production use.  
The Rapid Programming Algorithm reduces the time required to program the part and guaran-  
tees reliable programming. Programing time is typically only 50 µs/byte. The Integrated Product  
Identification Code electronically identifies the device and manufacturer. This feature is used by  
industry-standard programming equipment to select the proper programming algorithms and  
voltages. The AT27LV520 programs exactly the same way as a standard 5V AT27C520 and  
uses the same programming equipment.  
2. Pin Configurations  
Pin Name  
Function  
A8 - A15  
AD0 - AD7  
OE /VPP  
ALE  
Addresses  
Addresses/Outputs  
Output Enable/Program Supply  
Address Latch Enable  
2.ꢀ  
20-lead TSSOP Top View  
A10  
A12  
1
20  
19  
18  
17  
16  
15  
14  
13  
12  
11  
A8  
2
AD1  
AD3  
AD5  
AD7  
GND  
AD6  
AD4  
AD2  
AD0  
A14  
3
ALE  
4
VCC  
OE/VPP  
A15  
5
6
7
A13  
8
A11  
9
A9  
10  
2.2  
20-lead SOIC Top View  
OE/VPP  
A15  
1
20  
19  
18  
17  
16  
15  
14  
13  
12  
11  
VCC  
ALE  
A14  
A12  
A10  
A8  
2
A13  
3
A11  
4
A9  
5
AD0  
AD2  
AD4  
AD6  
GND  
6
7
AD1  
AD3  
AD5  
AD7  
8
9
10  
2
AT27LV520  
0911F–EPROM–10/05  
AT27LV520  
3. System Considerations  
Switching under active conditions may produce transient voltage excursions. Unless accommo-  
dated by the system design, these transients may exceed datasheet limits, resulting in device  
non-conformance. At a minimum, a 0.1 µF high frequency, low inherent inductance, ceramic  
capacitor should be utilized for each device. This capacitor should be connected between the  
V
CC and Ground terminals of the device, as close to the device as possible. Additionally, to sta-  
bilize the supply voltage level on printed circuit boards with large EPROM arrays, a 4.7 µF bulk  
electrolytic capacitor should be utilized, again connected between the VCC and Ground termi-  
nals. This capacitor should be positioned as close as possible to the point where the power  
supply is connected to the array.  
4. Block Diagram  
VCC  
GND  
8
OE/VPP  
ALE  
OE, ALE, AND  
OUTPUT  
PROGRAM LOGIC  
BUFFERS  
Y DECODER  
Y-GATING  
AD7 - AD0  
A15 - A8  
X DECODER  
CELL MATRIX  
8
IDENTIFICATION  
5. Absolute Maximum Ratings*  
Temperature under Bias ................................ -55°C to +125°C  
*NOTICE:  
Stresses beyond those listed under “Absolute  
Maximum Ratings” may cause permanent dam-  
age to the device. This is a stress rating only and  
functional operation of the device at these or any  
other conditions beyond those indicated in the  
operational sections of this specification is not  
implied. Exposure to absolute maximum rating  
conditions for extended periods may affect device  
reliability.  
Storage Temperature..................................... -65°C to +150°C  
Voltage on Any Pin with  
Respect to Ground .........................................-2.0V to +7.0V(1)  
Voltage on A9 with  
Respect to Ground ......................................-2.0V to +14.0V(1)  
VPP Supply Voltage with  
Respect to Ground .......................................-2.0V to +14.0V(1)  
Note:  
1. Minimum voltage is -0.6V DC which may undershoot to -2.0V for pulses of less than 20 ns. Maximum output pin voltage is  
VCC + 0.75V DC which may overshoot to +7.0V for pulses of less than 20 ns.  
3
0911F–EPROM–10/05  
 
6. Operating Modes  
Mode/Pin  
ALE  
VIL  
OE/VPP  
VIL  
A8 - Aꢀ5  
AD0 - AD7  
DOUT  
Read(2)  
Ai  
X(1)  
Ai  
Output Disable(2)  
VIL/VIH  
VIH  
VIH  
High Z/A0 - A7  
A0 - A7  
Standby  
VIH  
Address Latch Enable(2)  
Rapid Program(3)  
VIH  
VIH  
X
A0 - A7  
VIH  
VPP  
Ai  
DIN  
(5)  
A9 = VH  
Product Identification(4)  
VIL  
VIL  
A8 = VIH or VIL  
A10 - A15 = VIL  
Identification Code  
Notes: 1. X can be VIL or VIH.  
2. Read, output disable, and standby modes require 3.0V ≤ VCC ≤ 3.6V, or 4.5V ≤ VCC ≤ 5.5V.  
3. Refer to Programming Characteristics.  
4. VH = 12.0 0.5V.  
5. Two identifier bytes may be selected. All A8 - A15 inputs are held low (VIL), except A9 which is set to VH and A8 which is  
toggled low (VIL) to select the Manufacturer’s Identification byte and high (VIH) to select the Device Code byte.  
7. DC and AC Operating Conditions for Read Operation  
AT27LV520-70  
-40°C - +85°C  
3.0V to 3.6V  
5V 10%  
AT27LV520-90  
-40°C - +85°C  
3.0V to 3.6V  
5V 10%  
Industrial Operating Temp. (Case)  
CC Supply  
V
8. DC and Operating Characteristics for Read Operation  
Symbol  
Parameter  
Condition  
Min  
Max  
Units  
VCC = 3.0V to 3.6V  
ILI  
Input Load Current  
VIN = 0V to VCC  
1
µA  
µA  
µA  
mA  
V
ILO  
ISB  
ICC  
VIL  
VIH  
Output Leakage Current  
VCC Standby Current  
VCC Active Current  
Input Low Voltage  
VOUT = 0V to VCC  
5
20  
(1)  
ALE = VCC 0.3V; Ai, ADi = GND/VCC 0.3V  
f = 5 MHz, IOUT = 0 mA, ALE = VIL  
8
-0.6  
2.0  
0.8  
Input High Voltage  
Output Low Voltage  
Output High Voltage  
VCC + 0.5  
0.4  
V
VOL  
VOH  
IOL = 2.0 mA  
IOH = -2.0 mA  
V
2.4  
V
VCC = 4.5V to 5.5V  
ILI  
Input Load Current  
VIN = 0V to VCC  
1
5
µA  
µA  
µA  
mA  
V
ILO  
ISB  
ICC  
VIL  
VIH  
Output Leakage Current  
VCC Standby Current  
VCC Active Current  
Input Low Voltage  
VOUT = 0V to VCC  
(1)  
ALE = VCC 0.3V; Ai, ADi = GND/VCC 0.3V  
f = 5 MHz, IOUT = 0 mA, ALE = VIL  
100  
20  
-0.6  
2.0  
0.8  
Input High Voltage  
Output Low Voltage  
Output High Voltage  
VCC + 0.5  
0.4  
V
VOL  
VOH  
IOL = 2.1 mA  
IOH = -400 µA  
V
2.4  
Note:  
1. VCC standby current will be slightly higher with ALE, Ai, and ADi at TTL levels.  
4
AT27LV520  
0911F–EPROM–10/05  
 
 
 
 
 
AT27LV520  
9. AC Characteristics for Read Operation  
VCC = 3.0V to 3.6V and 4.5V to 5.5V  
AT27LV520-70  
AT27LV520-90  
Symbol  
Parameter  
Condition  
Min  
Max  
70  
Min  
Max  
90  
Units  
ns  
(3)  
tACC  
Address to Output Delay  
Address Latch Enable Low to Output Delay  
Address Setup Time  
ALE = OE/VPP = VIL  
Address Valid  
OE/VPP = VIH  
OE/VPP = VIH  
OE/VPP = VIH  
ALE = VIL  
tCE  
55  
70  
ns  
tAS  
tAH  
tALE  
12  
12  
40  
15  
15  
45  
ns  
Address Hold Time  
ns  
Address Latch Enable Width  
OE/VPP to Output Delay  
OE/VPP High to Output Float  
ns  
(3)  
tOE  
30  
25  
35  
25  
ns  
(4)(5)  
tDF  
ALE = VIL  
ns  
Output Hold from Address or OE/VPP,  
Whichever Occurred First  
7
0
ns  
tOH  
ALE = VIL  
ꢀ0. AC Waveforms for Read Operation(1)  
tALE  
ALE  
tCE  
OE/VPP  
tDF  
tOH  
DATA OUT  
tAS  
tAH  
tOE  
AD7 - AD0  
A15 - A8  
ADDRESS IN  
tACC  
Notes: 1. Timing measurement reference levels for all speed grades are VOL = 0.8V and VOH = 2.0V. Input AC drive levels are  
VIL = 0.45V and VIH = 2.4V.  
2. OE/VPP may be delayed up to tCE - tOE after the address is valid without impact on tCE  
.
3. OE/VPP may be delayed up to tACC - tOE after the address is valid without impact on tACC  
.
4. This parameter is only sampled and is not 100% tested.  
5. Output float is defined as the point when data is no longer driven.  
5
0911F–EPROM–10/05  
 
 
 
 
ꢀꢀ. Input Test Waveforms and Measurement Levels  
tR, tF < 20 ns (10% to 90%)  
ꢀ2. Output Test Load  
Note:  
CL = 100 pF including jig capacitance.  
ꢀ3. Pin Capacitance  
f = 1 MHz, T = 25°C(1)  
Symbol  
CIN  
Typ  
4
Max  
6
Units  
pF  
Conditions  
VIN = 0V  
COUT  
8
12  
pF  
VOUT = 0V  
Note:  
1. Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested.  
6
AT27LV520  
0911F–EPROM–10/05  
 
AT27LV520  
ꢀ4. Programming Waveforms  
PROGRAM  
READ (VERIFY)  
6.5V  
VCC  
5.0V  
13V  
tVCS  
OE/VPP  
VIH  
VIL  
tPRT  
tOES  
tOEH  
tVR  
tLP  
VIH  
ALE  
AD7 - AD0  
A15 - A8  
V
IL  
tALE  
tLAS  
tPW  
tALE  
tLAS  
tOE  
tDFP  
tDS  
DATA IN  
tLAH  
tDH  
tLAH  
VIH  
ADDR  
ADDR  
DATA OUT  
VIL  
tAS  
tAH  
VIH  
ADDRESS STABLE  
VIL  
Notes: 1. The Input Timing Reference is 0.8V for VIL and 2.0V for VIH.  
2. tOE and tDFP are characteristics of the device but must be accommodated by the programmer.  
ꢀ5. DC Programming Characteristics  
TA = 25 5°C, VCC = 6.5 0.25V, OE/VPP = 13.0 0.25V  
Limits  
Symbol  
ILI  
Parameter  
Test Conditions  
Min  
Max  
10  
Units  
µA  
V
Input Load Current  
Input Low Level  
VIN = VIL, VIH  
VIL  
-0.6  
2.0  
0.8  
VIH  
Input High Level  
VCC + 1.0  
0.4  
V
VOL  
VOH  
ICC2  
IPP2  
Output Low Voltage  
Output High Voltage  
VCC Supply Current (Program and Verify)  
OE/VPP Current  
IOL = 2.1 mA  
IOH = -400 µA  
V
2.4  
V
25  
25  
mA  
mA  
ALE = VIH  
7
0911F–EPROM–10/05  
ꢀ6. AC Programming Characteristics  
TA = 25 5°C, VCC = 6.5 0.25V, OE/VPP = 13.0 0.25V  
Limits  
Symbol  
tALE  
tLAS  
tLAH  
tLP  
Parameter(1)  
Test Conditions  
Min  
500  
100  
100  
2
Max  
Units  
ns  
ns  
ns  
µs  
µs  
µs  
µs  
µs  
µs  
µs  
µs  
ns  
ns  
µs  
µs  
Address Latch Enable Width  
Latched Address Setup Time  
Latched Address Hold Time  
ALE Low to OE/VPP High Voltage Delay  
OE/VPP Setup Time  
tOES  
tOEH  
tDS  
Input Rise and Fall Times:  
2
(10% to 90%) 20 ns  
OE/VPP Hold Time  
2
Data Setup Time  
2
Input Pulse Levels:  
tDH  
Data Hold Time  
2
0.45V to 2.4V  
tPW  
ALE Program Pulse Width(2)  
OE/VPP Recovery Time  
VCC Setup Time  
47.5  
2
52.5  
Input Timing Reference Level:  
0.8V to 2.0V  
tVR  
tVCS  
tOE  
tDFP  
tAS  
2
Output Timing Reference Level:  
0.8V to 2.0V  
Data Valid from OE/VPP  
OE/VPP High to Output Float Delay(3)  
Address Setup Time  
150  
130  
0
2
0
tAH  
Address Hold Time  
OE/VPP Pulse Rise Time During  
Programming  
tPRT  
50  
ns  
Notes: 1. VCC must be applied simultaneously or before OE/VPP and removed simultaneously or after OE/VPP  
.
2. Program Pulse width tolerance is 50 µsec 5%.  
3. This parameter is only sampled and is not 100% tested. Output Float is defined as the point where data is no longer driven –  
see timing diagram.  
ꢀ7. Atmel’s AT27LV520 Integrated Product Identification Code  
Pins  
Hex  
Codes  
A8  
0
AD7  
AD6  
AD5  
AD4  
AD3  
AD2  
ADꢀ  
AD0  
Data  
Manufacturer  
Device Type  
0
1
0
0
0
0
1
1
1
1
1
1
1
0
0
1
1E  
1
9D  
Note:  
1. The AT27LV520 has the same product identification code as the AT27C520. Both are programming compatible.  
8
AT27LV520  
0911F–EPROM–10/05  
 
 
 
AT27LV520  
ꢀ8. RapidProgramming Algorithm  
A 50 µs ALE pulse width is used to program. The address is set to the first location. VCC is raised  
to 6.5V and OE/VPP is raised to 13.0V. Each address is first programmed with one 50 µs ALE  
pulse without verification. Then a verification/reprogramming loop is executed for each address.  
In the event a byte fails to pass verification, up to 10 successive 50 µs pulses are applied with a  
verification after each pulse. If the byte fails to verify after 10 pulses have been applied, the part  
is considered failed. After the byte verifies properly, the next address is selected until all have  
been checked. OE/VPP is then lowered to VIH and VCC to 5.0V. All bytes are read again and com-  
pared with the original data to determine if the device passes or fails.  
START  
ADDR = FIRST LOCATION  
VCC = 6.5V  
VPP = 13.0V  
PROGRAM ONE 50 µS PULSE  
NO  
LAST  
INCREMENT ADDRESS  
ADDR.?  
YES  
ADDR = FIRST LOCATION  
X = 0  
INCREMENT ADDRESS  
NO  
LAST  
PASS  
FAIL  
VERIFY  
BYTE  
INCREMENT X  
ADDR.?  
YES  
NO  
PROGRAM ONE 50 µS PULSE  
X = 10?  
YES  
VCC = 5.0V  
VPP = 5.0V  
COMPARE  
FAIL  
DEVICE  
FAILED  
ALL BYTES  
TO ORIGINAL  
DATA  
PASS  
DEVICE  
PASSED  
9
0911F–EPROM–10/05  
ꢀ9. Ordering Information  
ꢀ9.ꢀ Standard Package  
ICC (mA)  
tACC (ns)  
Active  
Ordering Code  
Package  
Operation Range  
AT27LV520-70SI  
AT27LV520-70XI  
20S  
20X  
Industrial  
70  
8
(-40°C to +85°C)  
AT27LV520-90SI  
AT27LV520-90XI  
20S  
20X  
Industrial  
90  
8
(-40°C to +85°C)  
ꢀ9.2 Green Package (Pb/Halide-free)  
I
CC (mA)  
Active  
tACC (ns)  
Ordering Code  
Package  
Operation Range  
AT27LV520-70SU  
AT27LV520-70XU  
20S  
20X  
Industrial  
70  
8
8
(-40°C to +85°C)  
Industrial  
90  
AT27LV520-90XU  
20X  
(-40°C to +85°C)  
Package Type  
20-lead, 0.300" Wide, Plastic Gull Wing Small Outline (SOIC)  
20-lead, 4.4 mm Body Width, Plastic Thin Shrink Small Outline (TSSOP)  
20S  
20X  
ꢀ0  
AT27LV520  
0911F–EPROM–10/05  
AT27LV520  
20. Packaging Information  
20.ꢀ 20S – SOIC  
Dimensions in Millimeters and (Inches).  
Controlling dimension: Inches.  
JEDEC Standard MS-013  
0.51(0.020)  
0.33(0.013)  
10.65 (0.419)  
10.00 (0.394)  
7.60 (0.2992)  
7.40 (0.2914)  
PIN 1 ID  
PIN 1  
1.27 (0.050) BSC  
13.00 (0.5118)  
12.60 (0.4961)  
2.65 (0.1043)  
2.35 (0.0926)  
0.30(0.0118)  
0.10 (0.0040)  
0.32 (0.0125)  
0.23 (0.0091)  
0º ~ 8º  
1.27 (0.050)  
0.40 (0.016)  
10/23/03  
TITLE  
DRAWING NO. REV.  
2325 Orchard Parkway  
San Jose, CA 95131  
20S, 20-lead, 0.300" Body, Plastic Gull Wing Small Outline (SOIC)  
20S  
B
R
ꢀꢀ  
0911F–EPROM–10/05  
20.2 20X – TSSOP  
Dimensions in Millimeters and (Inches).  
Controlling dimension: Millimeters.  
JEDEC Standard MO-153 AC  
INDEX MARK  
PIN  
1
6.50 (0.256)  
6.25 (0.246)  
4.50 (0.177)  
4.30 (0.169)  
6.60 (.260)  
6.40 (.252)  
1.20 (0.047) MAX  
0.65 (.0256) BSC  
0.15 (0.006)  
0.05 (0.002)  
SEATING  
PLANE  
0.30 (0.012)  
0.19 (0.007)  
0.20 (0.008)  
0.09 (0.004)  
0º ~ 8º  
0.75 (0.030)  
0.45 (0.018)  
10/23/03  
TITLE  
DRAWING NO. REV.  
2325 Orchard Parkway  
San Jose, CA 95131  
20X, (Formerly 20T), 20-lead, 4.4 mm Body Width,  
Plastic Thin Shrink Small Outline Package (TSSOP)  
20X  
C
R
ꢀ2  
AT27LV520  
0911F–EPROM–10/05  
Atmel Corporation  
Atmel Operations  
2325 Orchard Parkway  
San Jose, CA 95131, USA  
Tel: 1(408) 441-0311  
Fax: 1(408) 487-2600  
Memory  
RF/Automotive  
Theresienstrasse 2  
Postfach 3535  
74025 Heilbronn, Germany  
Tel: (49) 71-31-67-0  
Fax: (49) 71-31-67-2340  
2325 Orchard Parkway  
San Jose, CA 95131, USA  
Tel: 1(408) 441-0311  
Fax: 1(408) 436-4314  
Regional Headquarters  
Microcontrollers  
2325 Orchard Parkway  
San Jose, CA 95131, USA  
Tel: 1(408) 441-0311  
Fax: 1(408) 436-4314  
1150 East Cheyenne Mtn. Blvd.  
Colorado Springs, CO 80906, USA  
Tel: 1(719) 576-3300  
Europe  
Atmel Sarl  
Route des Arsenaux 41  
Case Postale 80  
CH-1705 Fribourg  
Switzerland  
Tel: (41) 26-426-5555  
Fax: (41) 26-426-5500  
Fax: 1(719) 540-1759  
Biometrics/Imaging/Hi-Rel MPU/  
High Speed Converters/RF Datacom  
Avenue de Rochepleine  
La Chantrerie  
BP 70602  
44306 Nantes Cedex 3, France  
Tel: (33) 2-40-18-18-18  
Fax: (33) 2-40-18-19-60  
BP 123  
38521 Saint-Egreve Cedex, France  
Tel: (33) 4-76-58-30-00  
Fax: (33) 4-76-58-34-80  
Asia  
Room 1219  
Chinachem Golden Plaza  
77 Mody Road Tsimshatsui  
East Kowloon  
Hong Kong  
Tel: (852) 2721-9778  
Fax: (852) 2722-1369  
ASIC/ASSP/Smart Cards  
Zone Industrielle  
13106 Rousset Cedex, France  
Tel: (33) 4-42-53-60-00  
Fax: (33) 4-42-53-60-01  
1150 East Cheyenne Mtn. Blvd.  
Colorado Springs, CO 80906, USA  
Tel: 1(719) 576-3300  
Japan  
9F, Tonetsu Shinkawa Bldg.  
1-24-8 Shinkawa  
Chuo-ku, Tokyo 104-0033  
Japan  
Tel: (81) 3-3523-3551  
Fax: (81) 3-3523-7581  
Fax: 1(719) 540-1759  
Scottish Enterprise Technology Park  
Maxwell Building  
East Kilbride G75 0QR, Scotland  
Tel: (44) 1355-803-000  
Fax: (44) 1355-242-743  
Literature Requests  
www.atmel.com/literature  
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any  
intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI-  
TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY  
WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR  
PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDEN-  
TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT  
OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no  
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications  
and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided  
otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use  
as components in applications intended to support or sustain life.  
©
Atmel Corporation 2005. All rights reserved. Atmel®, logo and combinations thereof, Everywhere You Are® and others, are  
registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.  
Printed on recycled paper.  
0911F–EPROM–10/05