1L0591VGB01MA007--Datasheet/数据表在线中文翻译

The Full Color Series

1L0591VGB01MA007

◆Outline (L* H): 5.8*8.6mm

◆Good thermal dissipation & optical uniformity

Features

Table of Contents



Forward current: G/B≦30mA&R≦50mA

Typical view angle 50% Iv: 50°

Lens color: white diffused

Product Code Method------------------------------------------------2

Maximum Rating-----------------------------------------------------2

Typical Product Characteristics ------------------------------------3

Directive Characteristics --------------------------------------------3

Electronic-Optical Characteristics ---------------------------------4

Dimensions -----------------------------------------------------------5

Packing------------------------------------------------------------------6

Precautions ------------------------------------------------------------7

Test Items and Results of Reliability------------------------------10

RoHS2.0 and REACH-compliant

ESD level 1KV(HBM)

Applications



Indoor decorating

Marking light

Consumer electronics

Special applications

http://www.ystone.com.tw

The Full Color Series

 Product Code Method

-----------------------------------------------------------------------------------------------------------------------------------

1 - L - 05 - 91 - VGB0 - 1 - M - A - 0 - 07

① ②

③

④

⑤

⑥

⑦

⑧ ⑨ ⑩

①

②

③

④

⑤

Lead Frame

Code

Dice Wavelength

&Luminous rank

V: red

Process Type Product Type Specification

1 : normal process

L: lamp LED

05: round 5.8mm

91:frame

G:green

B: blue

⑥

⑦

⑧

⑨

⑩

Resin Color

Code

Article Mode Special Process

Polarity Code

Assembly Code

Code

Requirements

07:no expression above

meaning for company

1: common anode

M: white diffused

A: article mode

0: normal

 Maximum Rating(Ta=25℃)

------------------------------------------------------------------------------------------------------------------------------------

Characteristics

Symbol

Rating

Unit

G/B≦30mA&R≦50mA

DC Forward Current

Pulse Forward Current^*3

Reverse Voltage

I_F

mA

V

I_PF

V_R

100

5

Red

80

Power Dissipation

P_D

mW

Green & Blue

100

Junction Temperature

Operating Temperature Range

Storage Temperature Range

Soldering Temperature^*4

T_J

110

^oC

T_OP

T_STG

T_SD

-40-85

-40-100

260

Notes 1: There is no maximum or typical voltage parameter

2: For other ambient, limited setting of current will be depended on de-rating curves.

3: Duty 1/10, pulse width 0.1ms

4: The maximum of soldering time is 5 seconds in T_SD

http://www.ystone.com.tw

The Full Color Series

 Typical Product Characteristics(Ta=25℃)

------------------------------------------------------------------------------------------------------------------------------------

Characteristics

Symbol

red

Min.

Typ.

Max.

Unit

Test condition

1.7

2.8

460

780

210

620

520

462.5

-

2.0

3.2

900

1500

450

-

2.5

3.6

Forward Voltage

V_Fgreen

blue

V

I_F=20mA

3.6

red

1700

2800

780

630

535

472.5

10

Luminous Intensity

Iv

green

blue

red

mcd

nm

I_F=20mA

Dominant Wavelength

Reverse Current

λd

green

blue

-

I_R

2θ_1/2

-

μA

V_R= 5V

View Angle

-

50

-

deg

I_F=20mA

Notes: 1. Measurement Errors:

Forward Voltage: ±0.1V, Luminous Intensity: ±10%Iv, Dominant Wavelength: ±1.0nm

2. Electrical-Optical Characteristics (Ta=25℃)

 Directive Characteristics(Ta=25℃)

------------------------------------------------------------------------------------------------------------------------------------

Relative Radiant Intensity vs .Angular Displacement

http://www.ystone.com.tw

The Full Color Series

 Electronic-Optical Characteristics

------------------------------------------------------------------------------------------------------------------------------------

1). Forward Current I_F-V_F

2). Relative Luminous Intensity-I_F

30

10000

25

20

15

1000

100

10

5

0

30

25

20

0

5

10

15

1.5

2.5

Forward

Voltage (V)

3

3.5

2

)

urrent (mA

rd C

Forwa

3). Relative Luminous Intensity-Ta

4). Forward Current I_F-Ta

110%

50

100%

90%

40

30

20

80%

70%

10

0

20

40

60

80

100

0

20

40

60

80

100

Ambient Temperature Ta(°C)

Ambient Temperature(°C)

5). Forward Voltage-Ta

6). Wavelength Characteristics (Ta=25℃)

100%

80%

60%

40%

20%

0%

3.4

3.2

3.0

2.0

1.8

1.6

350

450

550

650

750

850

25

45

65

85

105

Wavelength(nm)

Ambient Temperature(°C)

http://www.ystone.com.tw

The Full Color Series

 Dimensions

------------------------------------------------------------------------------------------------------------------------------------

Notes: 1. All measurements are ±0.3 mm unless otherwise indicated.

2. The appearance of encapsulation tolerance is ±0.25 mm

3. The maximum dimensions of protruded resin flange (NOTE) is 1.0mm

http://www.ystone.com.tw

The Full Color Series

 Packing

------------------------------------------------------------------------------------------------------------------------------------

1. Package bag: vinyl bag(500pcs per bag)

2. Label: label as below(label on the left)

3. Package

3.1. ESD bag: 12bags per carton (6,000pcs per carton)

3.2. Carton size: 330*135*330mm

4. Falling

The falling off of the device: we have to ensure the max loss number of LAMP is 2pcs.

5. Different rank

The product of different rank will be separate in the same box

http://www.ystone.com.tw

The Full Color Series

 Precautions

------------------------------------------------------------------------------------------------------------------------------------

A. Storage

It can be stored for 3 months under conditions of Temperature 23+/-5 and humidity 30-65%。During

storage, there must not be any damage to the sealed bag, and if opened once, do not store again. After the

package is opened, the products should be used within one week under the same temperature and humidity.

B. Cleaning

Do not use any unidentified chemical to clean LEDS, it could damage or crack the LED epoxy surface.

If necessary, soak LED in alcohol for a time not exceeding one minute in normal temperature.

C. Lead Frames Shaping & Trimming

1. The shaping should be done underneath the wedge point. No pressure should be exerted to the epoxy

shell of the LED during shaping.

2. Shaping of the leads should be done before soldering.

3. Lead trimming should only be done at normal temperature.

D. Soldering

1. When soldering, the soldering iron needs to be at least 1.6mm away from the epoxy edge. Do not

apply any pressure to the epoxy encapsulation or the lead frame during the soldering process.

2. When reflow soldering or wave soldering, please solder once for less than 5 seconds at a maximum

temperature of 265°C. During the soldering process, if the temperature or timing is not controlled within

limits, it would cause the epoxy to deform or cause the die or wires within the LED to be damaged.

3. When using soldering iron, please solder once for less than 5 seconds at a maximum temperature of

350°C+10°C. When soldering a row of LED on a PCB, please do not solder both leads of a LED in sequence.

(Solder the positive lead at first, then the negative leads)

4. Do not dip the epoxy encapsulation part of LED into any soldering paste liquid.

5. After soldering, do not adjust the location of the LED anymore.

http://www.ystone.com.tw

The Full Color Series

 Precautions

------------------------------------------------------------------------------------------------------------------------------------

6. LED view

1) Bottom view:

2) Side view:

E. Installation

1. During the installation process, do not apply any pressure to the leads.

2. Please make sure the installation holes on the PCB matches the leads of the LED.

F. ESD (Electrostatic Discharge)

1. LED is very sensitive to ESD; please make sure during the whole usage and installation process, that no

ESD exist to affect the LED. Excessive ESD could damage the LED chip and result in performance

degradation.

2. LED can also be damaged by electrical surge, please make sure any driving electrical circuits are equipped

with surge protection.

3. During the installation process, please make sure all the equipment and personnel are grounded properly.

Make use ESD protection equipment such as anti-static gloves, anti-static wrist bands, anti-static mats,

anti-static clothes, anti-static shoes, and anti-static containers.

4. When LED come into contact with low electrical resistance metallic surfaces, the ESD could damage the

LED due to sudden discharge of ESD. Please make sure all surfaces that will be in contact with LED are

covered with anti-static mats (Surface electrical resistance of 10⁶~~10⁸Ω/sq). LED should be placed in

anti-static containers and anti-static bags.

http://www.ystone.com.tw

The Full Color Series

 Precautions

------------------------------------------------------------------------------------------------------------------------------------

G. Recommended Usage Guidelines

1. Please only use 20mA (Lamp LED) and 30mA (High Flux LED) of forward current to drive LEDS whether

one LED or multiple LEDS are being used.

2. Circuit connections

i. Serial connection

ii. Parallel connection

3. Sudden surge could damage the LED interior connections. Please design circuit with care so no sudden

voltage surge or current surge will show when turning the circuit on or off.

4. When color or brightness uniformity is required while using multiple LEDS, the LED driver condition is

critical. Our company guarantees the uniformity of the LEDS from the same bin when the driver current is

20mA (Lamp LED) and 30mA (High Flux LED)

H. Safety

1. Please comply with government electrical safety code while using the LEDS.

2. Do not look directly into a lit LED; it could damage the eyes after only a few seconds.

3. Do not look directly into powered UV LEDS; it could damage the eyes after only a few seconds.

(UV LEDS are mainly used in currency validating machines)

I.Direction

1. We are sending you our specification and drawings for your approval. Please return to us one copy

“For Approval” with your approved signatures.

2. Comply with HSF request of customers

http://www.ystone.com.tw

The Full Color Series

 Test Items and Results of Reliability

------------------------------------------------------------------------------------------------------------------------------------

Duration/

Cycle

Number of

Damage

Test Item

Ac/Re

Test Conditions

Reference

Ta＝23℃(±5℃)

Normal Temperature Life

High Temperature Life

JESD22 A-108

1008 hrs

0/1

0/22

I_F=20mA

Ta＝85℃(±5℃)

I_F=20mA

Ta＝85℃(±5℃)

RH=85%

High Humidity Heat Life

Thermal shock

JESD22 A-108

JESD22 A-104

1008 hrs

0/1

0/22

I_F=20mA

-45℃/30min~105℃

/30min

(±5℃)

According to the

SPEC

Electrostatic Discharge (ESD)

Test

AEC Q101-001

JESD22-A103D

3 cycles

1008 hrs

0/1

0/22

T_a=-40℃

T_a=125℃

Low Temperature Storage

High Temperature Storage

*Criteria for Judging

Item

Criteria for Judgment of Pass

Symbol

Condition

Min

Max

USL*¹×1.1

10μA

Forward Voltage

Reverse Current

V_F

I_R

I_F=20mA

V_R= 8V

-

Luminous Intensity

Iv

I_F=20mA

LSL^*2×0.7

-

[Note] USL*¹: Upper Specification Level

LSL*²: Lower Specification Level

http://www.ystone.com.tw