HSHM-S055CR4-5AP1-TR40B [3M]
55 CONTACT(S), FEMALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, PRESS FIT, SOCKET;
| 型号： | HSHM-S055CR4-5AP1-TR40B |
| 厂家： | 
3M ELECTRONICS |
| 描述： | 55 CONTACT(S), FEMALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, PRESS FIT, SOCKET PC 连接器 |
| 文件： | 总5页 (文件大小：1453K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
3M™ MetPak™ HSHM Press-Fit Socket
2 mm Type CR, 55 Signal Contacts, 5 Rows, Right Angle
HSHM Series
• Up to 5 Gb/s data rates
• Low crosstalk at high frequencies
• 50/100 Ω (single-ended /differential) impedance
• Modular/scalable format IEC 61076-4-101
• 63 mated lines per linear inch
• Mates with 3M™ MetPak™ HSHM headers
• Dual beam contact construction for high reliability
• End-to-end stackable with 5 row 3M™ MetPak™
CP2, HM and HSHM sockets
• See Regulatory Information Appendix (RIA) for
chemical compliance information
Date Modified: April 3, 2007
TS-2066-02
Sheet 1 of 3
Physical
Insulation Material
Flammability:
Contact
High Temperature Thermoplastic (LCP)
UL 94V-0
Material:
Copper Alloy
Plating:
See Ordering Information
Performance
Mechanical
Normal Force (Nominal):
Engagement Force (Nominal):
Separation Force (Nominal):
Wipe (Nominal, Shortest Contact):
Durability:
0.57 N [ 58 g ] Signal, 0.74 N [ 75 g ] Shield
0.32 N [ 33 g ] Signal, 0.22 N [ 22 g ] Shield
0.20 N [ 20 g ] Signal, 0.20 N [ 20 g ] Shield
2.67 mm [ 0.105 in. ] Signal, 1.57 mm [ 0.062 in ] Shield
250 cycles with TR40B plating
Application:
This module is not suitable for stand-alone use (Refer to IEC-61076-4-101)
Electrical
Data Rate:
5 Gb/s
Characteristic Impedance:
Current Rating (Fully Loaded):
50 Ω Single-ended, 100 Ω Differential
1 A at 70° C Signal
4
Insulation Resistance:
Withstanding Voltage:
10 MΩ at 100 VDC
750 VRMS
Environmental
Temperature Rating:
-55°C to +125°C
UL File No.: E68080
MetPak is a trademark of 3M Company.
3
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ MetPak™ HSHM Press-Fit Socket
2 mm Type CR, 55 Signal Contacts, 5 Rows, Right Angle
HSHM Series
HSHM-SXXXXX-5AP1-XXXXX
REV X
XXYY
25.00
.984
20.40
.803
20.00
.787
2.00
.079
2.00
.079
E
D
C
B
A
11.40
.449
10.95
.431
11 10
9
8
7
6
5
4
3
2
1
3.69
.145
1.00
.039
2.00
.079
2.00
.079
8.80
.346
10.70
.421
3.30
.130
18.00
.709
2.80
.110
mm
[inch]
Tolerance Unless Noted
0
0.0
0.00
mm
±3
±0.3 ±0.13
[ ] Dimensions for Reference Only
Ordering Information
HSHM - S055CRX - 5AP1 - XXXXX
High Speed Option:
Plating μm [ μ″ ]:
1 =Row differential applications
4 =Coaxial and column differential applications
7 =Stripline applications (75 Ω)
TG30 = 0.76 [ 30 ] Min. Au Contact Area
2.54 [ 100 ] Min. SnPb Terminal Area (RIA E2 & C2 apply)
1.27 [ 50 ] Min. Ni All over
TR40B = 0.127 [ 5 ] Min. Hard Au Contact Area, Lubricated
1.02 [ 40 ] Min. PdNi Contact Area
0.10 [ 4 ] Min. Pd Strike Contact Area
2.54 [ 100 ] Min. SnPb Terminal Area (RIA E2 & C2 apply)
1.27 [ 50 ] Min. Ni all over
TS-2066-02
Sheet 2 of 3
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3
Interconnect Solutions
http://www.3M.com/interconnects/
3M™ MetPak™ HSHM Press-Fit Socket
2 mm Type CR, 55 Signal Contacts, 5 Rows, Right Angle
HSHM Series
O DIM D
l Ø 0.10 M A B C
Plated thru holes
20.00
C
1.00
1.50
B
A
A
B
C
2.00
8.00
D
E
1
2
3
4
5
6
7
8
9
10 11
1.00
2.00
Recommended PCB hole mounting pattern for coaxial, column
differential and stripline applications
A
B
C
D
E
1
2
3
4
5
6
7
8
9
10 11
Recommended PCB hole mounting pattern for row differential
applications
(Same geometry as above without the ground vias)
HOLE PLATING TABLE mm (in.)
FINISHED HOLE DIA. "D"
Cu THICKNESS
SnPb THICKNESS
DRILLED HOLE DIA.
0.457 - 0.559 (.0180 - .0220)
0.584 - 0.625 (.0230 - .0246)
0.025 - 0.045 (.0010 - .0018)
0.008 -0.018 (.0003 - .0007)
TS-2066-02
Sheet 3 of 3
3
Interconnect Solutions
3M is a trademark of 3M Company.
For technical, sales or ordering information call
http://www.3M.com/interconnects/
800-225-5373
Regulatory Information Appendix
3M Electronic Solutions Division/Interconnect
EUROPE
Appendix E1: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product is RoHS Compliant 2005/95/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in
excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/
EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability
and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E2: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC
This product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is
compliant by exemption under EU Commission Decision 2005/747/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in
excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/
EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability
and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E3: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment as
amended by Commission Decision 2005/618/EC.
This product contains lead in the solder tail area in excess of the maximum concentration value allowed.
Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon
information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability
and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E4: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains decaBDE in the insulating material in excess of the maximum concentration value allowed but is
compliant by exemption under EU Commission Decision 2005/17/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in
excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision
2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in
writing, this information represents 3M’s best knowledge and belief based upon information provided by third party
suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability
and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
RIA-2217-B
CHINA
Appendix C1: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits
for Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006,
means that the product or part does not contain any of the following substances in excess of the following maximum
concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium,
polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise
stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by
third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability
and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
20
Appendix C2: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits
for Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006,
means that the product or part does contain a substance, as detailed in the chart below, in excess of the following
maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent
chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless
otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information
provided by third party suppliers to 3M.
The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an
extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform
with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in
accordance with the product Warranty stated below.
Name and Content of Hazardous Substances or Elements
Important Notice
All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the
accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended
application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s
current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in
writing, by an authorized officer of 3M.
Warranty; Limited Remedy; Limited Liability.
This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER
WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to
replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any
indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted.
3
Electronic Solutions Division
6801 River Place Blvd.
Austin, TX 78726-9000
800/225-5373
www.3M.com/interconnects
RIA-2217-B
© 3M 2007
相关型号：
HSHM-S088FL4-8AP1-TR40B
88 CONTACT(S), FEMALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, PRESS FIT, SOCKET
3M
HSHM-S088FL7-8AP1-TG30
88 CONTACT(S), FEMALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, PRESS FIT, SOCKET
3M
HSHM-S110APWR1-5AP1-TG50
110 CONTACT(S), FEMALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, PRESS FIT, SOCKET
3M
HSHM-S110APWR4-5AP1-TG30
110 CONTACT(S), FEMALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, PRESS FIT, SOCKET
3M
HSHM-S110APWR4-5AP1-TG30L
110 CONTACT(S), FEMALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, PRESS FIT, SOCKET
3M
HSHM-S176DPWR4-8AP1-TG30L
180 CONTACT(S), FEMALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, PRESS FIT, SOCKET, ROHS COMPLIANT
3M
HSHM-S200DE4-8AP1-TR40B
200 CONTACT(S), FEMALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, PRESS FIT, SOCKET
3M
HSHM-S200DE7-8AP1-TR40B
200 CONTACT(S), FEMALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, PRESS FIT, SOCKET
3M
HSHM-S200E1--8PAP1TR40B
200 CONTACT(S), FEMALE, RIGHT ANGLE TWO PART BOARD CONNECTOR, PRESS FIT, SOCKET
3M
HSHM-S200E1-8AP1-TG30
Board Connector, 200 Contact(s), 8 Row(s), Female, Right Angle, 0.079 inch Pitch, Press Fit Terminal, Locking, Plug,
3M
©2020 ICPDF网 联系我们和版权申明