S-1335L28-M5T1U3 [ABLIC]
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR;
| 型号： | S-1335L28-M5T1U3 |
| 厂家： | 
ABLIC |
| 描述： | HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR |
| 文件： | 总67页 (文件大小：756K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
S-1335 Series
HIGH RIPPLE-REJECTION SOFT-START FUNCTION
CMOS VOLTAGE REGULATOR
www.ablic.com
© ABLIC Inc., 2012-2014
Rev.1.3_02
The S-1335 Series, developed by using the CMOS technology, is a positive voltage regulator IC of 150 mA output current,
which has low dropout voltage, high-accuracy output voltage and soft-start function.
The rising time of output voltage immediately after power-on or after the ON / OFF pin is set to ON is adjustable. A 1.0 F
small ceramic capacitor can be used. It operates with low current consumption of 36 A typ. Furthermore the overcurrent
protection circuit prevents the load current from exceeding the capacity of output transistor.
SOT-23-5, SC-82AB and super small HSNT-4 (1010) packages realize high-density mounting.
Features
Output voltage:
1.0 V to 3.6 V, selectable in 0.05 V step
Input voltage:
1.5 V to 5.5 V
Output voltage accuracy:
Dropout voltage:
Current consumption:
1.0% (1.0 V to 1.45 V output product: 15 mV)
70 mV typ. (2.8 V output product, IOUT = 100 mA)
During operation: 36 A typ., 54 A max.
During power-off: 0.1 A typ., 1.0 A max.
Possible to output 150 mA (VIN VOUT(S) 1.0 V)*1
A ceramic capacitor of 1.0 F or more can be used.
70 dB typ. (f = 10 kHz, VOUT(S) 2.5 V)
Output current:
Input and output capacitors:
Ripple rejection:
80 dB typ. (f = 1.0 kHz)
Built-in soft-start circuit:
The rising time of output voltage immediately after power-on or after the
ON / OFF pin is set to ON is adjustable.
The soft-start time of SOT-23-5 can be switched to tSS0 = 0.1 ms typ. /
t
SS1 = 1.0 ms typ. with the SST pin.
The soft-start time of SC-82AB is fixed to tSS0 = 0.1 ms typ.
The soft-start time of HSNT-4 (1010) is fixed to either tSS0 = 0.1 ms typ.
or tSS1 = 1.0 ms typ.
Built-in overcurrent protection circuit:
Built-in ON / OFF circuit:
Limits overcurrent of output transistor.
Ensures long battery life.
Pull-down resistor is selectable.
Discharge shunt function is selectable.
Operation temperature range:
Lead-free (Sn 100%), halogen-free
Ta = 40°C to 85°C
*1. Attention should be paid to the power dissipation of the package when the output current is large.
Applications
Constant-voltage power supply for digital still camera, TV
Constant-voltage power supply for battery-powered device
Constant-voltage power supply for cellular phone
Constant-voltage power supply for portable equipment
Packages
SOT-23-5
SC-82AB
HSNT-4 (1010)
1
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
Block Diagrams
1. S-1335 Series A / E type
Function
Status
*1
ON / OFF logic
VOUT Discharge shunt
function
Active "H"
VIN
Available
Overcurrent
protection
circuit
Pull-down resistor Available
Soft-start time
(typ.)
A type: 0.1 ms
E type: 1.0 ms
Soft-start
circuit
ON / OFF
circuit
ON / OFF
Reference
voltage circuit
*1
VSS
*1. Parasitic diode
Figure 1
2. S-1335 Series B / F type
Function
Status
*1
ON / OFF logic
VOUT Discharge shunt
function
Active "H"
VIN
Available
Overcurrent
protection
circuit
Pull-down resistor Unavailable
Soft-start time
(typ.)
B type: 0.1 ms
F type: 1.0 ms
Soft-start
circuit
ON / OFF
circuit
ON / OFF
Reference
voltage circuit
*1
VSS
*1. Parasitic diode
Figure 2
2
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
3. S-1335 Series C / G type
Function
Status
*1
ON / OFF logic
VOUT Discharge shunt
function
Active "H"
VIN
Unavailable
Overcurrent
protection
circui
Pull-down resistor Available
Soft-start time
(typ.)
C type: 0.1 ms
G type: 1.0 ms
Soft-start
circuit
ON / OFF
circuit
ON / OFF
Reference
voltage circuit
VSS
*1. Parasitic diode
Figure 3
4. S-1335 Series D / H type
Function
Status
*1
ON / OFF logic
Active "H"
Discharge shunt
function
Pull-down resistor Unavailable
Soft-start time
(typ.)
VIN
VOUT
Unavailable
Overcurrent
protection
circuit
D type: 0.1 ms
H type: 1.0 ms
Soft-start
circuit
ON / OFF
circuit
ON / OFF
Reference
voltage circuit
VSS
*1. Parasitic diode
Figure 4
3
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
5. S-1335 Series J type
Function
Status
*1
ON / OFF logic
VOUT Discharge shunt
function
Active "H"
VIN
Available
Overcurrent
protection
circuit
Pull-down resistor Available
Soft-start time
(typ.)
0.1 ms / 1.0 ms
(Switchable)
Soft-start
circuit
SST
ON / OFF
circuit
ON / OFF
Reference
voltage circuit
*1
VSS
*1. Parasitic diode
Figure 5
6. S-1335 Series K type
Function
Status
*1
ON / OFF logic
Discharge shunt
function
Pull-down resistor Unavailable
Soft-start time
(typ.)
Active "H"
VIN
VOUT
Available
Overcurrent
protection
circuit
0.1 ms / 1.0 ms
(Switchable)
Soft-start
circuit
SST
ON / OFF
circuit
ON / OFF
Reference
voltage circuit
*1
VSS
*1. Parasitic diode
Figure 6
4
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
7. S-1335 Series L type
Function
Status
*1
ON / OFF logic
VOUT Discharge shunt
function
Active "H"
VIN
Unavailable
Overcurrent
protection
circuit
Pull-down resistor Available
Soft-start time
(typ.)
0.1 ms / 1.0 ms
(Switchable)
Soft-start
SST
circuit
ON / OFF
circuit
ON / OFF
Reference
voltage circuit
VSS
*1. Parasitic diode
Figure 7
8. S-1335 Series M type
Function
Status
*1
ON / OFF logic
Active "H"
Discharge shunt
function
Pull-down resistor Unavailable
Soft-start time
(typ.)
VIN
VOUT
Unavailable
Overcurrent
protection
circuit
0.1 ms / 1.0 ms
(Switchable)
Soft-start
circuit
SST
ON / OFF
circuit
ON / OFF
Reference
voltage circuit
VSS
*1. Parasitic diode
Figure 8
5
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
Product Name Structure
Users can select the product type, output voltage, and package type for the S-1335 Series. Refer to "1. Product
name" regarding the contents of product name, "2. Function list of product type" regarding the product type, "3.
Packages" regarding the package drawings, "4. Product name list" regarding details of the product name.
1. Product name
S-1335
x
xx
-
xxxx
U
3
Environmental code
U:
Lead-free (Sn 100%), halogen-free
Package abbreviation and IC packing specifications*1
M5T1: SOT-23-5, Tape
N4T1: SC-82AB, Tape
A4T2: HSNT-4 (1010), Tape
Output voltage*2
10 to 36
(e.g., when the output voltage is 1.0 V, it is expressed as 10.)
Product type*3
A to M
*1. Refer to the tape drawing.
*2. If you request the product which has 0.05 V step, contact our sales office.
*3. Refer to "2. Function list of product type".
2. Function list of product type
Table 1
Product ON / OFF Discharge Shunt Pull-down
Soft-start Time (typ.)
Package
SC-82AB,
HSNT-4 (1010)
SC-82AB,
HSNT-4 (1010)
SC-82AB,
HSNT-4 (1010)
SC-82AB,
HSNT-4 (1010)
HSNT-4 (1010)
HSNT-4 (1010)
HSNT-4 (1010)
HSNT-4 (1010)
Type
Logic
Function
Resistor
A
Active "H"
Available
Available
0.1 ms
0.1 ms
0.1 ms
0.1 ms
B
C
D
Active "H"
Active "H"
Active "H"
Available
Unavailable
Available
Unavailable
Unavailable
Unavailable
E
F
Active "H"
Active "H"
Active "H"
Active "H"
Active "H"
Active "H"
Active "H"
Active "H"
Available
Available
1.0 ms
1.0 ms
1.0 ms
1.0 ms
Available
Unavailable
Available
G
H
J
Unavailable
Unavailable
Available
Unavailable
Available
0.1 ms / 1.0 ms (Switchable) SOT-23-5
0.1 ms / 1.0 ms (Switchable) SOT-23-5
0.1 ms / 1.0 ms (Switchable) SOT-23-5
0.1 ms / 1.0 ms (Switchable) SOT-23-5
K
L
Available
Unavailable
Available
Unavailable
Unavailable
M
Unavailable
6
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
3. Packages
Table 2 Package Drawing Codes
Package Name
Dimension
Tape
Reel
Land
SOT-23-5
MP005-A-P-SD
NP004-A-P-SD
PL004-A-P-SD
MP005-A-C-SD
NP004-A-C-SD
NP004-A-C-S1
PL004-A-C-SD
MP005-A-R-SD
SC-82AB
NP004-A-R-SD
PL004-A-R-SD
HSNT-4 (1010)
PL004-A-L-SD
4. Product name list
4. 1 S-1335 Series A type
ON / OFF logic:
Discharge shunt function:
Pull-down resistor:
Soft-start time:
Active "H"
Available
Available
0.1 ms typ.
Table 3
SC-82AB
HSNT-4 (1010)
Output Voltage
S-1335A10-N4T1U3
S-1335A11-N4T1U3
S-1335A12-N4T1U3
S-1335A13-N4T1U3
S-1335A14-N4T1U3
S-1335A15-N4T1U3
S-1335A16-N4T1U3
S-1335A17-N4T1U3
S-1335A18-N4T1U3
S-1335A19-N4T1U3
S-1335A20-N4T1U3
S-1335A21-N4T1U3
S-1335A22-N4T1U3
S-1335A23-N4T1U3
S-1335A24-N4T1U3
S-1335A25-N4T1U3
S-1335A26-N4T1U3
S-1335A27-N4T1U3
S-1335A28-N4T1U3
S-1335A2J-N4T1U3
S-1335A29-N4T1U3
S-1335A30-N4T1U3
S-1335A31-N4T1U3
S-1335A32-N4T1U3
S-1335A33-N4T1U3
S-1335A34-N4T1U3
S-1335A35-N4T1U3
S-1335A36-N4T1U3
S-1335A10-A4T2U3
S-1335A11-A4T2U3
S-1335A12-A4T2U3
S-1335A13-A4T2U3
S-1335A14-A4T2U3
S-1335A15-A4T2U3
S-1335A16-A4T2U3
S-1335A17-A4T2U3
S-1335A18-A4T2U3
S-1335A19-A4T2U3
S-1335A20-A4T2U3
S-1335A21-A4T2U3
S-1335A22-A4T2U3
S-1335A23-A4T2U3
S-1335A24-A4T2U3
S-1335A25-A4T2U3
S-1335A26-A4T2U3
S-1335A27-A4T2U3
S-1335A28-A4T2U3
S-1335A2J-A4T2U3
S-1335A29-A4T2U3
S-1335A30-A4T2U3
S-1335A31-A4T2U3
S-1335A32-A4T2U3
S-1335A33-A4T2U3
S-1335A34-A4T2U3
S-1335A35-A4T2U3
S-1335A36-A4T2U3
1.0 V 15 mV
1.1 V 15 mV
1.2 V 15 mV
1.3 V 15 mV
1.4 V 15 mV
1.5 V 1.0%
1.6 V 1.0%
1.7 V 1.0%
1.8 V 1.0%
1.9 V 1.0%
2.0 V 1.0%
2.1 V 1.0%
2.2 V 1.0%
2.3 V 1.0%
2.4 V 1.0%
2.5 V 1.0%
2.6 V 1.0%
2.7 V 1.0%
2.8 V 1.0%
2.85 V 1.0%
2.9 V 1.0%
3.0 V 1.0%
3.1 V 1.0%
3.2 V 1.0%
3.3 V 1.0%
3.4 V 1.0%
3.5 V 1.0%
3.6 V 1.0%
Remark Please contact our sales office for products with specifications other than the above.
7
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
4. 2 S-1335 Series B type
ON / OFF logic:
Active "H"
Discharge shunt function: Available
Pull-down resistor:
Soft-start time:
Unavailable
0.1 ms typ.
Table 4
SC-82AB
HSNT-4 (1010)
Output Voltage
S-1335B10-N4T1U3
S-1335B11-N4T1U3
S-1335B12-N4T1U3
S-1335B13-N4T1U3
S-1335B14-N4T1U3
S-1335B15-N4T1U3
S-1335B16-N4T1U3
S-1335B17-N4T1U3
S-1335B18-N4T1U3
S-1335B19-N4T1U3
S-1335B20-N4T1U3
S-1335B21-N4T1U3
S-1335B22-N4T1U3
S-1335B23-N4T1U3
S-1335B24-N4T1U3
S-1335B25-N4T1U3
S-1335B26-N4T1U3
S-1335B27-N4T1U3
S-1335B28-N4T1U3
S-1335B2J-N4T1U3
S-1335B29-N4T1U3
S-1335B30-N4T1U3
S-1335B31-N4T1U3
S-1335B32-N4T1U3
S-1335B33-N4T1U3
S-1335B34-N4T1U3
S-1335B35-N4T1U3
S-1335B36-N4T1U3
S-1335B10-A4T2U3
S-1335B11-A4T2U3
S-1335B12-A4T2U3
S-1335B13-A4T2U3
S-1335B14-A4T2U3
S-1335B15-A4T2U3
S-1335B16-A4T2U3
S-1335B17-A4T2U3
S-1335B18-A4T2U3
S-1335B19-A4T2U3
S-1335B20-A4T2U3
S-1335B21-A4T2U3
S-1335B22-A4T2U3
S-1335B23-A4T2U3
S-1335B24-A4T2U3
S-1335B25-A4T2U3
S-1335B26-A4T2U3
S-1335B27-A4T2U3
S-1335B28-A4T2U3
S-1335B2J-A4T2U3
S-1335B29-A4T2U3
S-1335B30-A4T2U3
S-1335B31-A4T2U3
S-1335B32-A4T2U3
S-1335B33-A4T2U3
S-1335B34-A4T2U3
S-1335B35-A4T2U3
S-1335B36-A4T2U3
1.0 V 15 mV
1.1 V 15 mV
1.2 V 15 mV
1.3 V 15 mV
1.4 V 15 mV
1.5 V 1.0%
1.6 V 1.0%
1.7 V 1.0%
1.8 V 1.0%
1.9 V 1.0%
2.0 V 1.0%
2.1 V 1.0%
2.2 V 1.0%
2.3 V 1.0%
2.4 V 1.0%
2.5 V 1.0%
2.6 V 1.0%
2.7 V 1.0%
2.8 V 1.0%
2.85 V 1.0%
2.9 V 1.0%
3.0 V 1.0%
3.1 V 1.0%
3.2 V 1.0%
3.3 V 1.0%
3.4 V 1.0%
3.5 V 1.0%
3.6 V 1.0%
Remark Please contact our sales office for products with specifications other than the above.
8
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
4. 3 S-1335 Series C type
ON / OFF logic:
Active "H"
Discharge shunt function: Unavailable
Pull-down resistor:
Soft-start time:
Available
0.1 ms typ.
Table 5
SC-82AB
HSNT-4 (1010)
Output Voltage
S-1335C10-N4T1U3
S-1335C11-N4T1U3
S-1335C12-N4T1U3
S-1335C13-N4T1U3
S-1335C14-N4T1U3
S-1335C15-N4T1U3
S-1335C16-N4T1U3
S-1335C17-N4T1U3
S-1335C18-N4T1U3
S-1335C19-N4T1U3
S-1335C20-N4T1U3
S-1335C21-N4T1U3
S-1335C22-N4T1U3
S-1335C23-N4T1U3
S-1335C24-N4T1U3
S-1335C25-N4T1U3
S-1335C26-N4T1U3
S-1335C27-N4T1U3
S-1335C28-N4T1U3
S-1335C2J-N4T1U3
S-1335C29-N4T1U3
S-1335C30-N4T1U3
S-1335C31-N4T1U3
S-1335C32-N4T1U3
S-1335C33-N4T1U3
S-1335C34-N4T1U3
S-1335C35-N4T1U3
S-1335C36-N4T1U3
S-1335C10-A4T2U3
S-1335C11-A4T2U3
S-1335C12-A4T2U3
S-1335C13-A4T2U3
S-1335C14-A4T2U3
S-1335C15-A4T2U3
S-1335C16-A4T2U3
S-1335C17-A4T2U3
S-1335C18-A4T2U3
S-1335C19-A4T2U3
S-1335C20-A4T2U3
S-1335C21-A4T2U3
S-1335C22-A4T2U3
S-1335C23-A4T2U3
S-1335C24-A4T2U3
S-1335C25-A4T2U3
S-1335C26-A4T2U3
S-1335C27-A4T2U3
S-1335C28-A4T2U3
S-1335C2J-A4T2U3
S-1335C29-A4T2U3
S-1335C30-A4T2U3
S-1335C31-A4T2U3
S-1335C32-A4T2U3
S-1335C33-A4T2U3
S-1335C34-A4T2U3
S-1335C35-A4T2U3
S-1335C36-A4T2U3
1.0 V 15 mV
1.1 V 15 mV
1.2 V 15 mV
1.3 V 15 mV
1.4 V 15 mV
1.5 V 1.0%
1.6 V 1.0%
1.7 V 1.0%
1.8 V 1.0%
1.9 V 1.0%
2.0 V 1.0%
2.1 V 1.0%
2.2 V 1.0%
2.3 V 1.0%
2.4 V 1.0%
2.5 V 1.0%
2.6 V 1.0%
2.7 V 1.0%
2.8 V 1.0%
2.85 V 1.0%
2.9 V 1.0%
3.0 V 1.0%
3.1 V 1.0%
3.2 V 1.0%
3.3 V 1.0%
3.4 V 1.0%
3.5 V 1.0%
3.6 V 1.0%
Remark Please contact our sales office for products with specifications other than the above.
9
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
4. 4 S-1335 Series D type
ON / OFF logic:
Active "H"
Discharge shunt function: Unavailable
Pull-down resistor:
Soft-start time:
Unavailable
0.1 ms typ.
Table 6
SC-82AB
HSNT-4 (1010)
Output Voltage
S-1335D10-N4T1U3
S-1335D11-N4T1U3
S-1335D12-N4T1U3
S-1335D13-N4T1U3
S-1335D14-N4T1U3
S-1335D15-N4T1U3
S-1335D16-N4T1U3
S-1335D17-N4T1U3
S-1335D18-N4T1U3
S-1335D19-N4T1U3
S-1335D20-N4T1U3
S-1335D21-N4T1U3
S-1335D22-N4T1U3
S-1335D23-N4T1U3
S-1335D24-N4T1U3
S-1335D25-N4T1U3
S-1335D26-N4T1U3
S-1335D27-N4T1U3
S-1335D28-N4T1U3
S-1335D2J-N4T1U3
S-1335D29-N4T1U3
S-1335D30-N4T1U3
S-1335D31-N4T1U3
S-1335D32-N4T1U3
S-1335D33-N4T1U3
S-1335D34-N4T1U3
S-1335D35-N4T1U3
S-1335D36-N4T1U3
S-1335D10-A4T2U3
S-1335D11-A4T2U3
S-1335D12-A4T2U3
S-1335D13-A4T2U3
S-1335D14-A4T2U3
S-1335D15-A4T2U3
S-1335D16-A4T2U3
S-1335D17-A4T2U3
S-1335D18-A4T2U3
S-1335D19-A4T2U3
S-1335D20-A4T2U3
S-1335D21-A4T2U3
S-1335D22-A4T2U3
S-1335D23-A4T2U3
S-1335D24-A4T2U3
S-1335D25-A4T2U3
S-1335D26-A4T2U3
S-1335D27-A4T2U3
S-1335D28-A4T2U3
S-1335D2J-A4T2U3
S-1335D29-A4T2U3
S-1335D30-A4T2U3
S-1335D31-A4T2U3
S-1335D32-A4T2U3
S-1335D33-A4T2U3
S-1335D34-A4T2U3
S-1335D35-A4T2U3
S-1335D36-A4T2U3
1.0 V 15 mV
1.1 V 15 mV
1.2 V 15 mV
1.3 V 15 mV
1.4 V 15 mV
1.5 V 1.0%
1.6 V 1.0%
1.7 V 1.0%
1.8 V 1.0%
1.9 V 1.0%
2.0 V 1.0%
2.1 V 1.0%
2.2 V 1.0%
2.3 V 1.0%
2.4 V 1.0%
2.5 V 1.0%
2.6 V 1.0%
2.7 V 1.0%
2.8 V 1.0%
2.85 V 1.0%
2.9 V 1.0%
3.0 V 1.0%
3.1 V 1.0%
3.2 V 1.0%
3.3 V 1.0%
3.4 V 1.0%
3.5 V 1.0%
3.6 V 1.0%
Remark Please contact our sales office for products with specifications other than the above.
10
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
4. 5 S-1335 Series E type
ON / OFF logic:
Active "H"
Discharge shunt function: Available
Pull-down resistor:
Soft-start time:
Available
1.0 ms typ.
Table 7
HSNT-4 (1010)
S-1335E10-A4T2U3
Output Voltage
1.0 V 15 mV
1.1 V 15 mV
1.2 V 15 mV
1.3 V 15 mV
1.4 V 15 mV
1.5 V 1.0%
1.6 V 1.0%
1.7 V 1.0%
1.8 V 1.0%
1.9 V 1.0%
2.0 V 1.0%
2.1 V 1.0%
2.2 V 1.0%
2.3 V 1.0%
2.4 V 1.0%
2.5 V 1.0%
2.6 V 1.0%
2.7 V 1.0%
2.8 V 1.0%
2.85 V 1.0%
2.9 V 1.0%
3.0 V 1.0%
3.1 V 1.0%
3.2 V 1.0%
3.3 V 1.0%
3.4 V 1.0%
3.5 V 1.0%
3.6 V 1.0%
S-1335E11-A4T2U3
S-1335E12-A4T2U3
S-1335E13-A4T2U3
S-1335E14-A4T2U3
S-1335E15-A4T2U3
S-1335E16-A4T2U3
S-1335E17-A4T2U3
S-1335E18-A4T2U3
S-1335E19-A4T2U3
S-1335E20-A4T2U3
S-1335E21-A4T2U3
S-1335E22-A4T2U3
S-1335E23-A4T2U3
S-1335E24-A4T2U3
S-1335E25-A4T2U3
S-1335E26-A4T2U3
S-1335E27-A4T2U3
S-1335E28-A4T2U3
S-1335E2J-A4T2U3
S-1335E29-A4T2U3
S-1335E30-A4T2U3
S-1335E31-A4T2U3
S-1335E32-A4T2U3
S-1335E33-A4T2U3
S-1335E34-A4T2U3
S-1335E35-A4T2U3
S-1335E36-A4T2U3
Remark Please contact our sales office for products with specifications other than the above.
11
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
4. 6 S-1335 Series F type
ON / OFF logic:
Active "H"
Discharge shunt function: Available
Pull-down resistor:
Soft-start time:
Unavailable
1.0 ms typ.
Table 8
HSNT-4 (1010)
S-1335F10-A4T2U3
Output Voltage
1.0 V 15 mV
1.1 V 15 mV
1.2 V 15 mV
1.3 V 15 mV
1.4 V 15 mV
1.5 V 1.0%
1.6 V 1.0%
1.7 V 1.0%
1.8 V 1.0%
1.9 V 1.0%
2.0 V 1.0%
2.1 V 1.0%
2.2 V 1.0%
2.3 V 1.0%
2.4 V 1.0%
2.5 V 1.0%
2.6 V 1.0%
2.7 V 1.0%
2.8 V 1.0%
2.85 V 1.0%
2.9 V 1.0%
3.0 V 1.0%
3.1 V 1.0%
3.2 V 1.0%
3.3 V 1.0%
3.4 V 1.0%
3.5 V 1.0%
3.6 V 1.0%
S-1335F11-A4T2U3
S-1335F12-A4T2U3
S-1335F13-A4T2U3
S-1335F14-A4T2U3
S-1335F15-A4T2U3
S-1335F16-A4T2U3
S-1335F17-A4T2U3
S-1335F18-A4T2U3
S-1335F19-A4T2U3
S-1335F20-A4T2U3
S-1335F21-A4T2U3
S-1335F22-A4T2U3
S-1335F23-A4T2U3
S-1335F24-A4T2U3
S-1335F25-A4T2U3
S-1335F26-A4T2U3
S-1335F27-A4T2U3
S-1335F28-A4T2U3
S-1335F2J-A4T2U3
S-1335F29-A4T2U3
S-1335F30-A4T2U3
S-1335F31-A4T2U3
S-1335F32-A4T2U3
S-1335F33-A4T2U3
S-1335F34-A4T2U3
S-1335F35-A4T2U3
S-1335F36-A4T2U3
Remark Please contact our sales office for products with specifications other than the above.
12
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
4. 7 S-1335 Series G type
ON / OFF logic:
Active "H"
Discharge shunt function: Unavailable
Pull-down resistor:
Soft-start time:
Available
1.0 ms typ.
Table 9
HSNT-4 (1010)
S-1335G10-A4T2U3
Output Voltage
1.0 V 15 mV
1.1 V 15 mV
1.2 V 15 mV
1.3 V 15 mV
1.4 V 15 mV
1.5 V 1.0%
1.6 V 1.0%
1.7 V 1.0%
1.8 V 1.0%
1.9 V 1.0%
2.0 V 1.0%
2.1 V 1.0%
2.2 V 1.0%
2.3 V 1.0%
2.4 V 1.0%
2.5 V 1.0%
2.6 V 1.0%
2.7 V 1.0%
2.8 V 1.0%
2.85 V 1.0%
2.9 V 1.0%
3.0 V 1.0%
3.1 V 1.0%
3.2 V 1.0%
3.3 V 1.0%
3.4 V 1.0%
3.5 V 1.0%
3.6 V 1.0%
S-1335G11-A4T2U3
S-1335G12-A4T2U3
S-1335G13-A4T2U3
S-1335G14-A4T2U3
S-1335G15-A4T2U3
S-1335G16-A4T2U3
S-1335G17-A4T2U3
S-1335G18-A4T2U3
S-1335G19-A4T2U3
S-1335G20-A4T2U3
S-1335G21-A4T2U3
S-1335G22-A4T2U3
S-1335G23-A4T2U3
S-1335G24-A4T2U3
S-1335G25-A4T2U3
S-1335G26-A4T2U3
S-1335G27-A4T2U3
S-1335G28-A4T2U3
S-1335G2J-A4T2U3
S-1335G29-A4T2U3
S-1335G30-A4T2U3
S-1335G31-A4T2U3
S-1335G32-A4T2U3
S-1335G33-A4T2U3
S-1335G34-A4T2U3
S-1335G35-A4T2U3
S-1335G36-A4T2U3
Remark Please contact our sales office for products with specifications other than the above.
13
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
4. 8 S-1335 Series H type
ON / OFF logic:
Active "H"
Discharge shunt function: Unavailable
Pull-down resistor:
Soft-start time:
Unavailable
1.0 ms typ.
Table 10
HSNT-4 (1010)
S-1335H10-A4T2U3
Output Voltage
1.0 V 15 mV
1.1 V 15 mV
1.2 V 15 mV
1.3 V 15 mV
1.4 V 15 mV
1.5 V 1.0%
1.6 V 1.0%
1.7 V 1.0%
1.8 V 1.0%
1.9 V 1.0%
2.0 V 1.0%
2.1 V 1.0%
2.2 V 1.0%
2.3 V 1.0%
2.4 V 1.0%
2.5 V 1.0%
2.6 V 1.0%
2.7 V 1.0%
2.8 V 1.0%
2.85 V 1.0%
2.9 V 1.0%
3.0 V 1.0%
3.1 V 1.0%
3.2 V 1.0%
3.3 V 1.0%
3.4 V 1.0%
3.5 V 1.0%
3.6 V 1.0%
S-1335H11-A4T2U3
S-1335H12-A4T2U3
S-1335H13-A4T2U3
S-1335H14-A4T2U3
S-1335H15-A4T2U3
S-1335H16-A4T2U3
S-1335H17-A4T2U3
S-1335H18-A4T2U3
S-1335H19-A4T2U3
S-1335H20-A4T2U3
S-1335H21-A4T2U3
S-1335H22-A4T2U3
S-1335H23-A4T2U3
S-1335H24-A4T2U3
S-1335H25-A4T2U3
S-1335H26-A4T2U3
S-1335H27-A4T2U3
S-1335H28-A4T2U3
S-1335H2J-A4T2U3
S-1335H29-A4T2U3
S-1335H30-A4T2U3
S-1335H31-A4T2U3
S-1335H32-A4T2U3
S-1335H33-A4T2U3
S-1335H34-A4T2U3
S-1335H35-A4T2U3
S-1335H36-A4T2U3
Remark Please contact our sales office for products with specifications other than the above.
14
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
4. 9 S-1335 Series J type
ON / OFF logic:
Active "H"
Discharge shunt function: Available
Pull-down resistor:
Soft-start time:
Available
0.1 ms typ. / 1.0 ms typ. (Switchable)
Table 11
SOT-23-5
Output Voltage
S-1335J10-M5T1U3
S-1335J11-M5T1U3
S-1335J12-M5T1U3
S-1335J13-M5T1U3
S-1335J14-M5T1U3
S-1335J15-M5T1U3
S-1335J16-M5T1U3
S-1335J17-M5T1U3
S-1335J18-M5T1U3
S-1335J19-M5T1U3
S-1335J20-M5T1U3
S-1335J21-M5T1U3
S-1335J22-M5T1U3
S-1335J23-M5T1U3
S-1335J24-M5T1U3
S-1335J25-M5T1U3
S-1335J26-M5T1U3
S-1335J27-M5T1U3
S-1335J28-M5T1U3
S-1335J2J-M5T1U3
S-1335J29-M5T1U3
S-1335J30-M5T1U3
S-1335J31-M5T1U3
S-1335J32-M5T1U3
S-1335J33-M5T1U3
S-1335J34-M5T1U3
S-1335J35-M5T1U3
S-1335J36-M5T1U3
1.0 V 15 mV
1.1 V 15 mV
1.2 V 15 mV
1.3 V 15 mV
1.4 V 15 mV
1.5 V 1.0%
1.6 V 1.0%
1.7 V 1.0%
1.8 V 1.0%
1.9 V 1.0%
2.0 V 1.0%
2.1 V 1.0%
2.2 V 1.0%
2.3 V 1.0%
2.4 V 1.0%
2.5 V 1.0%
2.6 V 1.0%
2.7 V 1.0%
2.8 V 1.0%
2.85 V 1.0%
2.9 V 1.0%
3.0 V 1.0%
3.1 V 1.0%
3.2 V 1.0%
3.3 V 1.0%
3.4 V 1.0%
3.5 V 1.0%
3.6 V 1.0%
Remark Please contact our sales office for products with specifications other than the above.
15
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
4. 10 S-1335 Series K type
ON / OFF logic:
Active "H"
Discharge shunt function: Available
Pull-down resistor:
Soft-start time:
Unavailable
0.1 ms typ. / 1.0 ms typ. (Switchable)
Table 12
SOT-23-5
Output Voltage
S-1335K10-M5T1U3
S-1335K11-M5T1U3
S-1335K12-M5T1U3
S-1335K13-M5T1U3
S-1335K14-M5T1U3
S-1335K15-M5T1U3
S-1335K16-M5T1U3
S-1335K17-M5T1U3
S-1335K18-M5T1U3
S-1335K19-M5T1U3
S-1335K20-M5T1U3
S-1335K21-M5T1U3
S-1335K22-M5T1U3
S-1335K23-M5T1U3
S-1335K24-M5T1U3
S-1335K25-M5T1U3
S-1335K26-M5T1U3
S-1335K27-M5T1U3
S-1335K28-M5T1U3
S-1335K2J-M5T1U3
S-1335K29-M5T1U3
S-1335K30-M5T1U3
S-1335K31-M5T1U3
S-1335K32-M5T1U3
S-1335K33-M5T1U3
S-1335K34-M5T1U3
S-1335K35-M5T1U3
S-1335K36-M5T1U3
1.0 V 15 mV
1.1 V 15 mV
1.2 V 15 mV
1.3 V 15 mV
1.4 V 15 mV
1.5 V 1.0%
1.6 V 1.0%
1.7 V 1.0%
1.8 V 1.0%
1.9 V 1.0%
2.0 V 1.0%
2.1 V 1.0%
2.2 V 1.0%
2.3 V 1.0%
2.4 V 1.0%
2.5 V 1.0%
2.6 V 1.0%
2.7 V 1.0%
2.8 V 1.0%
2.85 V 1.0%
2.9 V 1.0%
3.0 V 1.0%
3.1 V 1.0%
3.2 V 1.0%
3.3 V 1.0%
3.4 V 1.0%
3.5 V 1.0%
3.6 V 1.0%
Remark Please contact our sales office for products with specifications other than the above.
16
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
4. 11 S-1335 Series L type
ON / OFF logic:
Active "H"
Discharge shunt function: Unavailable
Pull-down resistor:
Soft-start time:
Available
0.1 ms typ. / 1.0 ms typ. (Switchable)
Table 13
SOT-23-5
Output Voltage
S-1335L10-M5T1U3
S-1335L11-M5T1U3
S-1335L12-M5T1U3
S-1335L13-M5T1U3
S-1335L14-M5T1U3
S-1335L15-M5T1U3
S-1335L16-M5T1U3
S-1335L17-M5T1U3
S-1335L18-M5T1U3
S-1335L19-M5T1U3
S-1335L20-M5T1U3
S-1335L21-M5T1U3
S-1335L22-M5T1U3
S-1335L23-M5T1U3
S-1335L24-M5T1U3
S-1335L25-M5T1U3
S-1335L26-M5T1U3
S-1335L27-M5T1U3
S-1335L28-M5T1U3
S-1335L2J-M5T1U3
S-1335L29-M5T1U3
S-1335L30-M5T1U3
S-1335L31-M5T1U3
S-1335L32-M5T1U3
S-1335L33-M5T1U3
S-1335L34-M5T1U3
S-1335L35-M5T1U3
S-1335L36-M5T1U3
1.0 V 15 mV
1.1 V 15 mV
1.2 V 15 mV
1.3 V 15 mV
1.4 V 15 mV
1.5 V 1.0%
1.6 V 1.0%
1.7 V 1.0%
1.8 V 1.0%
1.9 V 1.0%
2.0 V 1.0%
2.1 V 1.0%
2.2 V 1.0%
2.3 V 1.0%
2.4 V 1.0%
2.5 V 1.0%
2.6 V 1.0%
2.7 V 1.0%
2.8 V 1.0%
2.85 V 1.0%
2.9 V 1.0%
3.0 V 1.0%
3.1 V 1.0%
3.2 V 1.0%
3.3 V 1.0%
3.4 V 1.0%
3.5 V 1.0%
3.6 V 1.0%
Remark Please contact our sales office for products with specifications other than the above.
17
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
4. 12 S-1335 Series M type
ON / OFF logic:
Active "H"
Discharge shunt function: Unavailable
Pull-down resistor:
Soft-start time:
Unavailable
0.1 ms typ. / 1.0 ms typ. (Switchable)
Table 14
SOT-23-5
Output Voltage
S-1335M10-M5T1U3
S-1335M11-M5T1U3
S-1335M12-M5T1U3
S-1335M13-M5T1U3
S-1335M14-M5T1U3
S-1335M15-M5T1U3
S-1335M16-M5T1U3
S-1335M17-M5T1U3
S-1335M18-M5T1U3
S-1335M19-M5T1U3
S-1335M20-M5T1U3
S-1335M21-M5T1U3
S-1335M22-M5T1U3
S-1335M23-M5T1U3
S-1335M24-M5T1U3
S-1335M25-M5T1U3
S-1335M26-M5T1U3
S-1335M27-M5T1U3
S-1335M28-M5T1U3
S-1335M2J-M5T1U3
S-1335M29-M5T1U3
S-1335M30-M5T1U3
S-1335M31-M5T1U3
S-1335M32-M5T1U3
S-1335M33-M5T1U3
S-1335M34-M5T1U3
S-1335M35-M5T1U3
S-1335M36-M5T1U3
1.0 V 15 mV
1.1 V 15 mV
1.2 V 15 mV
1.3 V 15 mV
1.4 V 15 mV
1.5 V 1.0%
1.6 V 1.0%
1.7 V 1.0%
1.8 V 1.0%
1.9 V 1.0%
2.0 V 1.0%
2.1 V 1.0%
2.2 V 1.0%
2.3 V 1.0%
2.4 V 1.0%
2.5 V 1.0%
2.6 V 1.0%
2.7 V 1.0%
2.8 V 1.0%
2.85 V 1.0%
2.9 V 1.0%
3.0 V 1.0%
3.1 V 1.0%
3.2 V 1.0%
3.3 V 1.0%
3.4 V 1.0%
3.5 V 1.0%
3.6 V 1.0%
Remark Please contact our sales office for products with specifications other than the above.
18
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
Pin Configurations
1. SOT-23-5
Table 15
Pin No.
Symbol
VIN
Description
1
2
3
Input voltage pin
GND pin
VSS
Top view
ON / OFF
ON / OFF pin
5
4
Switching pin for soft-start time
"H": tSS0 = 0.1 ms typ.
"L": tSS1 = 1.0 ms typ.
Output voltage pin
4
5
SST
VOUT
1
2
3
Remark The soft-start time can be switched to tSS0 = 0.1 ms typ. /
tSS1 = 1.0 ms typ. with the SST pin.
Refer to "2. Function list of product type" in " Product
Name Structure" for details.
Figure 9
2. SC-82AB
Top view
Table 16
Pin No.
Symbol
ON / OFF
VSS
Description
4
3
1
2
3
4
ON / OFF pin
GND pin
VOUT
Output voltage pin
Input voltage pin
1
2
VIN
Remark The soft-start time is fixed to tSS0 = 0.1 ms typ.
Refer to "2. Function list of product type" in " Product
Name Structure" for details.
Figure 10
3. HSNT-4 (1010)
Table 17
Pin No.
Symbol
VOUT
Description
Output voltage pin
Top view
1
2
3
4
1
2
4
3
VSS
GND pin
ON / OFF
VIN
ON / OFF pin
Input voltage pin
Bottom view
Remark The soft-start time is fixed to either tSS0 = 0.1 ms typ. or
tSS1 = 1.0 ms typ.
4
3
1
2
Refer to "2. Function list of product type" in " Product
Name Structure" for details.
*1
*1. Connect the heat sink of backside
at shadowed area to the board,
and set electric potential open or
GND.
However, do not use it as the
function of electrode.
Figure 11
19
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
Absolute Maximum Ratings
Table 18
(Ta = 25C unless otherwise specified)
Item
Symbol
VIN
VON / OFF
VSST
Absolute Maximum Rating
Unit
V
VSS 0.3 to VSS 6.0
VSS 0.3 to VSS 6.0
VSS 0.3 to VSS 6.0
VSS 0.3 to VIN 0.3
200
V
Input voltage
V
Output voltage
Output current
SOT-23-5
VOUT
V
IOUT
mA
mW
mW
mW
°C
°C
600*1
Power dissipation
SC-82AB
PD
400*1
HSNT-4 (1010)
340*1
Operation ambient temperature
Storage temperature
Topr
Tstg
40 to 85
40 to 125
*1. When mounted on board
[Mounted board]
(1) Board size:
(2) Name:
114.3 mm 76.2 mm t1.6 mm
JEDEC STANDARD51-7
Caution The absolute maximum ratings are rated values exceeding which the product could suffer physical
damage. These values must therefore not be exceeded under any conditions.
1200
HSNT-4(1010)
1000
800
600
400
200
0
SC-82AB
SOT-23-5
100
150
50
0
Ambient temperature (Ta) [C]
Figure 12 Power Dissipation of Package (When Mounted on Board)
20
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
Power Dissipation of HSNT-4 (1010) (Reference)
Power dissipation of package differs depending on the mounting conditions.
Consider the power dissipation characteristics under the following conditions as reference.
[Mounted board]
(1) Board size:
40 mm 40 mm t0.8 mm
Glass epoxy resin (four layers)
50%
When mounted on board (wind speed: 0 m/s)
Refer to the recommended land pattern (drawing code:PL004-A-L-SD)
(2) Board material:
(3) Wiring ratio:
(4) Test conditions:
(5) Land pattern:
1200
1000
800
600
400
200
0
100
150
50
0
Ambient temperature (Ta) [C]
Figure 13 Power Dissipation of Package (When Mounted on Board)
Table 19
Thermal Resistance Value (j－a)
115°C/W
Condition
Power Dissipation (Reference)
870 mW
HSNT-4 (1010) (When mounted on board)
21
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
Electrical Characteristics
1. S-1335 Series A / B / C / D / E / F / G / H type
Table 20
(Ta = 25C unless otherwise specified)
Test
Circuit
Item
Symbol
Condition
Min.
Typ.
Max. Unit
VOUT(S)
0.015
VOUT(S)
0.99
150*5
VOUT(S)
0.015
VOUT(S)
1.01
1.0 V VOUT(S) < 1.5 V
1.5 V VOUT(S) 3.6 V
VOUT(S)
V
V
1
V
IN = VOUT(S) 1.0 V,
Output voltage*1
Output current*2
VOUT(E)
I
OUT = 30 mA
VOUT(S)
1
IOUT
VIN VOUT(S) 1.0 V
mA
V
3
1
1
1
1
1
1
1
1
1
1
1.0 V VOUT(S) < 1.1 V
1.1 V VOUT(S) < 1.2 V
1.2 V VOUT(S) < 1.3 V
1.3 V VOUT(S) < 1.4 V
1.4 V VOUT(S) < 1.5 V
1.5 V VOUT(S) < 1.7 V
1.7 V VOUT(S) < 2.0 V
2.0 V VOUT(S) < 2.5 V
2.5 V VOUT(S) < 2.8 V
2.8 V VOUT(S) 3.6 V
0.130 0.250 0.350
0.225 0.275
0.194 0.224
0.160 0.187
0.124 0.167
0.104 0.157
0.094 0.140
0.084 0.127
0.077 0.117
0.070 0.103
V
V
V
V
Dropout voltage*3
Vdrop
IOUT = 100 mA
V
V
V
V
V
VOUT1
VINVOUT
VOUT2
VOUT
TaVOUT
Line regulation
VOUT(S) 0.5 V VIN 5.5 V, IOUT = 30 mA
0.05
15
0.2
40
%/V
mV
1
1
1
Load regulation
Output voltage
VIN = VOUT(S) 1.0 V, 1 mA IOUT 150 mA
VIN = VOUT(S) 1.0 V, IOUT = 30 mA,
40C Ta 85C
100
ppm/C
temperature coefficient*4
Current consumption
during operation
Current consumption
during power-off
Input voltage
V
IN = VOUT(S) 1.0 V, ON / OFF pin = ON,
no load
IN = VOUT(S) 1.0 V, ON / OFF pin = OFF,
no load
ISS1
36
54
A
2
V
ISS2
VIN
0.1
1.0
5.5
A
V
2
4
1.5
1.0
ON / OFF pin
input voltage "H"
ON / OFF pin
V
IN = VOUT(S) 1.0 V, RL = 1.0 k
determined by VOUT output level
IN = VOUT(S) 1.0 V, RL = 1.0 k
determined by VOUT output level
B / D / F / H type
VSH
V
V
VSL
ISH
ISL
0.3
0.1
5.0
0.1
V
4
4
4
4
input voltage "L"
0.1
1.0
A
A
A
(without pull-down resistor)
A / C / E / G type
ON / OFF pin
input current "H"
V
IN = 5.5 V,
VON / OFF = 5.5 V
2.5
(with pull-down resistor)
ON / OFF pin
input current "L"
VIN = 5.5 V, VON / OFF = 0 V
0.1
1.0 V
2.5 V
VOUT(S)
VOUT(S)
2.5 V
3.6 V
70
65
dB
dB
5
5
VIN = VOUT(S)
1.0 V, f = 10 kHz,
Vrip = 0.5 Vrms, IOUT = 30 mA
<
RR
Ripple rejection
VIN = VOUT(S)
1.0 V, f = 1.0 kHz,
1.0 V
VOUT(S)
3.6 V
80
50
dB
mA
ms
5
3
1
Vrip = 0.5 Vrms, IOUT = 30 mA
Short-circuit current
Soft-start time*6
Ishort
tSS0
VIN = VOUT(S) 1.0 V, ON / OFF pin = ON, VOUT = 0 V
A / B / C / D type
(0.1 ms typ.)
VIN = VOUT(S) 1.0 V,
OUT = 100 mA,
0.08
0.1
0.13
I
CL = 1.0 F,
tr = 1.0 s
E / F / G / H type
(1.0 ms typ.)
tSS1
0.8
1.0
35
1.2
ms
1
3
4
"L" output Nch
ON resistance
Power-off pull-down
resistance
V
IN = 5.5 V,
A / B / E / F type
RLOW
RPD
VOUT = 0.1 V (with discharge shunt function)
A / C / E / G type
(with pull-down resistor)
1.1
2.2
5.5
M
22
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
*1. VOUT(S): Set output voltage
VOUT(E): Actual output voltage
Output voltage when fixing IOUT (= 30 mA) and inputting VOUT(S) 1.0 V
*2. The output current at which the output voltage becomes 95% of VOUT(E) after gradually increasing the output current.
*3. Vdrop = VIN1 (VOUT3 0.98)
VOUT3 is the output voltage when VIN = VOUT(S) 1.0 V and IOUT = 100 mA.
VIN1 is the input voltage at which the output voltage becomes 98% of VOUT3 after gradually decreasing the input
voltage.
*4. A change in temperature of the output voltage [mV/°C] is calculated using the following equation.
VOUT
Ta
VOUT
TaVOUT
mV/°C *1 = VOUT(S)
V
[ ]
*2
ppm/°C *3 1000
[ ]
[
]
*1. Change in temperature of output voltage
*2. Set output voltage
*3. Output voltage temperature coefficient
*5. The output current can be at least this value.
Due to restrictions on the package power dissipation, this value may not be satisfied. Attention should be paid to the
power dissipation of the package when the output current is large.
This specification is guaranteed by design.
*6. Soft-start time shows the time period from when the input voltage reaches 50% until the output voltage rises to 99%,
immediately after power-on or when the ON / OFF pin is set to ON (tr = 1.0 s). Refer to "8. Soft-start function" in "
Operation" for details.
23
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
2. S-1335 Series J / K / L / M type
Table 21
(Ta = 25C unless otherwise specified)
Test
Circuit
Item
Symbol
Condition
Min.
Typ.
Max. Unit
VOUT(S)
0.015
VOUT(S)
0.99
VOUT(S)
0.015
VOUT(S)
1.01
VOUT(S)
V
V
6
1.0 V VOUT(S) < 1.5 V
VIN = VOUT(S) 1.0 V,
OUT = 30 mA
Output voltage*1
Output current*2
VOUT(E)
I
VOUT(S)
6
1.5 V VOUT(S) 3.6 V
IOUT
VIN VOUT(S) 1.0 V
150*5
mA
V
V
V
V
V
V
V
V
8
6
6
6
6
6
6
6
6
6
6
0.130 0.250 0.350
1.0 V VOUT(S) < 1.1 V
1.1 V VOUT(S) < 1.2 V
1.2 V VOUT(S) < 1.3 V
1.3 V VOUT(S) < 1.4 V
1.4 V VOUT(S) < 1.5 V
1.5 V VOUT(S) < 1.7 V
1.7 V VOUT(S) < 2.0 V
2.0 V VOUT(S) < 2.5 V
2.5 V VOUT(S) < 2.8 V
2.8 V VOUT(S) 3.6 V
0.225 0.275
0.194 0.224
0.160 0.187
0.124 0.167
0.104 0.157
0.094 0.140
0.084 0.127
0.077 0.117
0.070 0.103
Dropout voltage*3
Vdrop
IOUT = 100 mA
V
V
VOUT1
VINVOUT
VOUT2
VOUT
TaVOUT
Line regulation
Load regulation
0.05
15
0.2
40
%/V
mV
6
6
6
VOUT(S) 0.5 V VIN 5.5 V, IOUT = 30 mA
VIN = VOUT(S) 1.0 V, 1 mA IOUT 150 mA
VIN = VOUT(S) 1.0 V, IOUT = 30 mA,
40C Ta 85C
Output voltage
100
ppm/C
temperature coefficient*4
Current consumption
during operation
VIN = VOUT(S) 1.0 V, ON / OFF pin = ON,
no load
ISS1
36
54
7
A
Current consumption
during power-off
Input voltage
ON / OFF pin
input voltage "H"
VIN = VOUT(S) 1.0 V, ON / OFF pin = OFF,
ISS2
VIN
0.1
1.0
5.5
7
9
A
V
no load
1.5
1.0
VIN = VOUT(S) 1.0 V, RL = 1.0 k
determined by VOUT output level
VSH
V
ON / OFF pin
input voltage "L"
VIN = VOUT(S) 1.0 V, RL = 1.0 k
determined by VOUT output level
K / M type
VSL
ISH
ISL
0.3
0.1
5.0
0.1
V
9
9
9
9
0.1
1.0
A
A
A
(without pull-down resistor)
J / L type
ON / OFF pin
input current "H"
VIN = 5.5 V,
VON / OFF = 5.5 V
2.5
(with pull-down resistor)
ON / OFF pin
input current "L"
VIN = 5.5 V, VON / OFF = 0 V
0.1
70
65
dB
dB
10
10
1.0 V
2.5 V
VOUT(S)
VOUT(S)
2.5 V
3.6 V
VIN = VOUT(S)
1.0 V, f = 10 kHz,
Vrip = 0.5 Vrms, IOUT = 30 mA
<
RR
Ripple rejection
VIN = VOUT(S)
1.0 V, f = 1.0 kHz,
80
dB
10
1.0 V
VOUT(S)
3.6 V
Vrip = 0.5 Vrms, IOUT = 30 mA
Short-circuit current
Soft-start time*6
Ishort
tSS0
tSS1
50
0.1
1.0
mA
ms
ms
8
6
6
VIN = VOUT(S)
1.0 V, ON / OFF pin = ON, VOUT = 0 V
0.08
0.8
0.13
1.2
VSST = "H"
VSST = "L"
VIN = VOUT(S)
CL = 1.0 F, tr = 1.0 s
VIN = 5.5 V, J / K type
1.0 V, IOUT = 100 mA,
"L" output Nch
ON resistance
Power-off pull-down
resistance
RLOW
RPD
35
2.2
8
9
9
9
VOUT = 0.1 V (with discharge shunt function)
J / L type
(with pull-down resistor)
1.1
1.0
5.5
M
V
VIN = VON / OFF = VOUT(S) 1.0 V, RL = 1.0 k,
determined by VOUT output level
VIN = VON / OFF = VOUT(S) 1.0 V, RL = 1.0 k,
determined by VOUT output level
VIN = 5.5 V, VSST = 5.5 V
SST pin input voltage "H" VSH2
SST pin input voltage "L" VSL2
0.3
V
SST pin input current "H" ISH2
SST pin input current "L" ISL2
0.1
5.0
9
9
0.1
1.0
2.5
A
A
VIN = 5.5 V, VSST = 0 V
SST pin pull-up
resistance
RPU
1.1
2.2
5.5
9
M
24
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
*1. VOUT(S): Set output voltage
VOUT(E): Actual output voltage
Output voltage when fixing IOUT (= 30 mA) and inputting VOUT(S) 1.0 V
*2. The output current at which the output voltage becomes 95% of VOUT(E) after gradually increasing the output current.
*3. Vdrop = VIN1 (VOUT3 0.98)
VOUT3 is the output voltage when VIN = VOUT(S) 1.0 V and IOUT = 100 mA.
VIN1 is the input voltage at which the output voltage becomes 98% of VOUT3 after gradually decreasing the input
voltage.
*4. A change in temperature of the output voltage [mV/°C] is calculated using the following equation.
VOUT
Ta
VOUT
TaVOUT
mV/°C *1 = VOUT(S)
V
[ ]
*2
ppm/°C *3 1000
[ ]
[
]
*1. Change in temperature of output voltage
*2. Set output voltage
*3. Output voltage temperature coefficient
*5. The output current can be at least this value.
Due to restrictions on the package power dissipation, this value may not be satisfied. Attention should be paid to the
power dissipation of the package when the output current is large.
This specification is guaranteed by design.
*6. Soft-start time shows the time period from when the input voltage reaches 50% until the output voltage rises to 99%,
immediately after power-on or when the ON / OFF pin is set to ON (tr = 1.0 s). Refer to "8. Soft-start function" in "
Operation" for details.
25
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
Test Circuits
1. S-1335 Series A / B / C / D / E / F / G / H type
VOUT
VSS
VIN
A
ON / OFF
V
Set to ON
Figure 14 Test Circuit 1
A
VOUT
VIN
ON / OFF
VSS
Set to VIN or GND
Figure 15 Test Circuit 2
VOUT
VSS
A
VIN
ON / OFF
V
Set to ON
Figure 16 Test Circuit 3
VOUT
VSS
VIN
ON / OFF
A
V
RL
Figure 17 Test Circuit 4
VOUT
VIN
ON / OFF
V
RL
VSS
Set to ON
Figure 18 Test Circuit 5
26
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
2. S-1335 Series J / K / L / M type
VOUT
VIN
A
SST
VSS
ON / OFF
V
Set to ON
Figure 19 Test Circuit 6
A
VOUT
VIN
SST
VSS
ON / OFF
Set to VIN or GND
Figure 20 Test Circuit 7
VOUT
A
VIN
SST
VSS
ON / OFF
V
Set to ON
Figure 21 Test Circuit 8
VOUT
SST
VIN
A
ON / OFF
A
V
RL
Figure 22 Test Circuit 9
VOUT
VIN
SST
VSS
ON / OFF
V
RL
Set to ON
Figure 23 Test Circuit 10
27
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
Standard Circuit
Input
CIN
Output
VIN
VOUT
SST*3
*1
*2
ON / OFF
CL
VSS
Single GND
GND
*1.
CIN is a capacitor for stabilizing the input.
*2. A Ceramic capacitor of 1.0 F or more can be used as CL.
*3. S-1335 Series J / K / L / M type only.
Figure 24
Caution The above connection diagram and constant will not guarantee successful operation. Perform
thorough evaluation using the actual application to set the constant.
Condition of Application
Input capacitor (CIN):
Output capacitor (CL):
1.0 F or more
1.0 F or more
Caution
1. Set input capacitor (CIN) and output capacitor (CL) as CIN = CL.
2. Generally a series regulator may cause oscillation, depending on the selection of external parts.
Confirm that no oscillation occurs in the application for which the above capacitors are used.
Selection of Input and Output Capacitors (CIN, CL)
The S-1335 Series requires an output capacitor between the VOUT pin and the VSS pin for phase compensation.
Operation is stabilized by a ceramic capacitor with an output capacitance of 1.0 F or more over the entire temperature
range. When using an OS capacitor, a tantalum capacitor, or an aluminum electrolytic capacitor, the capacitance must
be 1.0 F or more.
The values of output overshoot and undershoot, which are transient response characteristics, vary depending on the
value of output capacitor.
The required value of capacitance for the input capacitor differs depending on the application.
Set the value for input capacitor (CIN) and output capacitor (CL) as follows. Define the values by sufficient evaluation
including the temperature characteristics under the usage condition.
CIN 1.0 F
CL 1.0 F
CIN = CL
28
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
Explanation of Terms
1. Low dropout voltage regulator
This voltage regulator has the low dropout voltage due to its built-in low on-resistance transistor.
2. Output voltage (VOUT
)
The accuracy of the output voltage is ensured at 1.0% or 15 mV*1 under the specified conditions of fixed input
voltage*2, fixed output current, and fixed temperature.
*1. When VOUT < 1.5 V: 15 mV, when VOUT ≥1.5 V: 1.0%
*2. Differs depending on the product.
Caution If the above conditions change, the output voltage value may vary and exceed the accuracy range
of the output voltage. Refer to " Electrical Characteristics" and " Characteristics (Typical Data)"
for details.
VOUT1
3. Line regulation
V V
OUT
IN
Indicates the dependency of the output voltage on the input voltage. That is, the values show how much the output
voltage changes due to a change in the input voltage with the output current remaining unchanged.
4. Load regulation (VOUT2
)
Indicates the dependency of the output voltage on the output current. That is, the values show how much the output
voltage changes due to a change in the output current with the input voltage remaining unchanged.
5. Dropout voltage (Vdrop
)
Indicates the difference between input voltage (VIN1) and the output voltage when; decreasing input voltage (VIN)
gradually until the output voltage has dropped out to the value of 98% of output voltage (VOUT3), which is at VIN
=
VOUT(S) 1.0 V.
Vdrop = VIN1 (VOUT3 0.98)
29
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
VOUT
6. Output voltage temperature coefficient
TaV
OUT
The shaded area in Figure 25 is the range where VOUT varies in the operation temperature range when the output
voltage temperature coefficient is 100 ppm/C.
Example of S-1335A30 typ. product
VOUT
[V]
0.30 mV/C
*1
VOUT(E)
0.30 mV/C
40
25
Ta [C]
85
*1.
V
OUT(E) is the value of the output voltage measured at Ta = 25C.
Figure 25
A change in the temperature of the output voltage [mV/°C] is calculated using the following equation.
VOUT
Ta
VOUT
TaVOUT
mV/°C *1 = VOUT(S)
V
[ ]
*2
ppm/°C *3 1000
[ ]
[
]
*1. Change in temperature of output voltage
*2. Set output voltage
*3. Output voltage temperature coefficient
30
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
Operation
1. Basic operation
Figure 26 shows the block diagram of the S-1335 Series.
The error amplifier compares the reference voltage (Vref) with feedback voltage (Vfb), which is the output voltage
resistance-divided by feedback resistors (Rs and Rf). It supplies the gate voltage necessary to maintain the constant
output voltage which is not influenced by the input voltage and temperature change, to the output transistor.
VIN
*1
Current
supply
Error
amplifier
VOUT
Vref
Rf
Vfb
Reference voltage
circuit
Rs
VSS
*1. Parasitic diode
Figure 26
2. Output transistor
In the S-1335 Series, a low on-resistance P-channel MOS FET is used as the output transistor.
Be sure that VOUT does not exceed VIN 0.3 V to prevent the voltage regulator from being damaged due to inverse
current flowing from the VOUT pin through a parasitic diode to the VIN pin, when the potential of VOUT became higher
than VIN.
31
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
3. ON / OFF pin
This pin starts and stops the regulator.
When the ON / OFF pin is set to OFF level, the entire internal circuit stops operating, and the built-in P-channel MOS
FET output transistor between the VIN pin and the VOUT pin is turned off, reducing current consumption significantly.
Note that the current consumption increases when a voltage of 0.3 V to 1.0 V is applied to the ON / OFF pin.
The ON / OFF pin is configured as shown in Figure 27 and Figure 28.
3. 1 S-1335 Series A / C / E / G / J / L type
The ON / OFF pin is internally pulled down to the VSS pin in the floating status, so the VOUT pin is set to the VSS
level.
3. 2 S-1335 Series B / D / F / H / K / M type
The ON / OFF pin is not internally pulled up or pulled down to the VSS pin, so do not use it in the floating status.
When not using the ON / OFF pin, connect the pin to the VIN pin.
Table 22
Product Type
ON / OFF Pin
"H": ON
Internal Circuit
VOUT Pin Voltage Current Consumption
A / B / C / D / E / F /
G / H / J / K / L / M
A / B / C / D / E / F /
G / H / J / K / L / M
*1
Operate
Set value
ISS1
Stop
VSS level
"L": OFF
ISS2
*1. Note that the IC's current consumption increases as much as current flows into the pull-down resistor of
2.2 M typ. when the ON / OFF pin is connected to the VIN pin and the S-1335 Series A / C / E / G / J / L
type is operating (refer to Figure 27).
VIN
VIN
ON / OFF
ON / OFF
VSS
VSS
Figure 27 S-1335 Series A / C / E / G / J / L type
Figure 28 S-1335 Series B / D / F / H / K / M type
32
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
4. Discharge shunt function (S-1335 Series A / B / E / F / J / K type)
The S-1335 Series A / B / E / F / J / K type has a built-in discharge shunt circuit to discharge the output capacitance.
The output capacitance is discharged as follows so that the VOUT pin reaches the VSS level.
(1) The ON / OFF pin is set to OFF level.
(2) The output transistor is turned off.
(3) The discharge shunt circuit is turned on.
(4) The output capacitor discharges.
Since the S-1335 Series C / D / G / H / L / M type does not have a discharge shunt circuit, the VOUT pin is set to the
VSS level through several hundred k internal divided resistors between the VOUT pin and the VSS pin. The S-1335
Series A / B / E / F / J / K type allows the VOUT pin to reach the VSS level rapidly due to the discharge shunt circuit.
S-1335 Series A / B / E / F / J / K type
Output transistor: OFF
*1
VOUT
VIN
Discharge shunt circuit
: ON
Output
capacitor
*1
(CL)
ON / OFF
ON / OFF circuit
ON / OFF pin: OFF
Current flow
GND
VSS
*1. Parasitic diode
Figure 29
5. Pull-down resistor (S-1335 Series A / C / E / G / J / L type)
The ON / OFF pin is internally pulled down to the VSS pin in the floating status, so the VOUT pin is set to the VSS
level.
Note that the IC’s current consumption increases as much as current flows into the pull-down resistor of 2.2 M typ.
when the ON / OFF pin is connected to the VIN pin.
33
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
6. Overcurrent protection circuit
The S-1335 Series includes an overcurrent protection circuit having the characteristics shown in "1. Output voltage
vs. Output current (When load current increases) (Ta = 25C)" in " Characteristics (Typical Data)", in order to
protect the output transistor against an excessive output current and short circuiting between the VOUT pin and the
VSS pin.
The current when the output pin is short-circuited (Ishort) is internally set at approx. 50 mA typ., and the normal value is
restored for the output voltage, if releasing a short circuit once.
Caution This overcurrent protection circuit does not work as for thermal protection. If this IC long keeps
short circuiting inside, pay attention to the conditions of input voltage and load current so that,
under the usage conditions including short circuit, the loss of the IC will not exceed power
dissipation of the package.
7. SST pin (S-1335 Series J / K / L / M type only)
In the S-1335 Series J / K / L / M type, the soft-start time can be switched with the SST pin. The soft-start time is set to
0.1 ms typ. if "H" is input to the SST pin, and set to 1.0 ms typ. if "L" is input to the SST pin. Refer to "8. 2 Switching
of soft-start time (S-1335 Series J / K / L / M type only)" for details.
The SST pin is configured as shown in Figure 30.
Note that the current consumption increases when a voltage of 0.3 V to 1.0 V is applied to the SST pin.
Since the SST pin is pulled up by the VIN pin internally, the soft-start time is fixed to 0.1 ms typ. on floating status.
Note that the IC’s current consumption increases as much as current flows into the pull-up resistor of 2.2 M typ. when
the SST pin is connected to the VSS pin and the S-1335 Series J / K / L / M type is operating (refer to Figure 30).
Table 23
SST Pin Input
Soft-start Time (typ.)
0.1 ms
"H"
"L"
1.0 ms
VIN
SST
VSS
Figure 30 S-1335 Series J / K / L / M type
34
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
8. Soft-start function
8. 1 Basic operation
The S-1335 Series has a built-in soft-start circuit to suppress the inrush current and overshoot of the output voltage
generated at power-on or at the time when the ON / OFF pin is set to ON. Immediately after power-on or after the
ON / OFF pin is set to ON, the output voltage slowly rises.
Immediately after power-on or when the ON / OFF pin is set to ON (tr = 1.0 s), the soft-start time (tSS) is the time
period from when the input voltage reaches 50% until the output voltage rises to 99%.
tr = 1.0 s
VOUT(S) 1.0 V
VIN 0.50
Input voltage
(VIN)
VOUT 0.99
Output voltage
(VOUT
)
Soft-start time (tSS
)
Figure 31 Basic Operation
The inrush current can be suppressed greatly by the soft-start function.
Figure 32 shows the waveform example of the inrush current.
Input voltage
(VIN)
Without soft-start function
With soft-start function
Inrush current
(IRUSH
)
Figure 32 Waveform Example of Inrush Current
35
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
8. 2 Switching of soft-start time (S-1335 Series J / K / L / M type only)
In the S-1335 Series J / K / L / M type, the soft-start time can be switched to tSS0 = 0.1 ms typ. / tSS1 = 1.0 ms typ.
with the SST pin.
However, the soft-start time (tSS) is as follows when the SST pin is switched within the soft-start time tSS0 = 0.1 ms
typ. / tSS1 = 1.0 ms typ.
8. 2. 1 When SST pin voltage (VSST) is switched from "H" to "L"
The soft-start time (tSS) is calculated by using the following equation.
t
SS = tSS0' tSS1 {1 VOUT(E)' / (VOUT(E) 0.99)}
tSS0': The time period that VSST is switched from "H" to "L" after power-on
t
SS1: The soft-start time when VSST = "L"
V
V
OUT(E)': The output voltage when VSST is switched from "H" to "L"
OUT(E): The output voltage after the end of the soft-start time
tr = 1.0 s
VOUT(S) 1.0 V
Input voltage
(VIN)
VIN 0.50
SST pin voltage
VSL2
(VSST
)
VOUT(E)
VOUT(E) 0.99
Output voltage
(VOUT
)
VOUT(E)'
tSS0
Soft-start time (tSS
Figure 33 SST = "H" "L"
'
)
V
tr = 1.0 s
VOUT(S) 1.0 V
Input voltage
(VIN)
VIN 0.50
SST pin voltage
(VSST
)
VOUT(E)
Output voltage
(VOUT
)
Soft-start time (tSS1
)
Figure 34
VSST = "L"
36
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
8. 2. 2 When SST pin voltage (VSST) is switched from "L" to "H"
The soft-start time (tSS) is calculated by using the following equation.
tSS = tSS1' tSS0 {1 VOUT(E)' / (VOUT(E) 0.99)}
tSS1': The time period that VSST is switched from "L" to "H" after power-on
t
SS0: The soft-start time when VSST = "H"
V
V
OUT(E)': The output voltage when VSST is switched from "L" to "H"
OUT(E): The output voltage after the end of the soft-start time
tr = 1.0 s
VOUT(S) 1.0 V
Input voltage
(VIN)
VIN 0.50
SST pin voltage
(VSST
)
VSH2
VOUT(E)
VOUT(E) 0.99
VOUT(E)
'
Output voltage
(VOUT
)
tSS1
'
Soft-start time (tSS
)
Figure 35 VSST = "L" "H"
tr = 1.0 s
VOUT(S) 1.0 V
Input voltage
(VIN)
VIN 0.50
SST pin voltage
(VSST
)
VOUT(E)
Output voltage
(VOUT
)
Soft-start time (tSS0
)
Figure 36 VSST = "H"
37
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
Precautions
Wiring patterns for the VIN pin, the VOUT pin and GND should be designed so that the impedance is low. When
mounting an output capacitor between the VOUT pin and the VSS pin (CL) and a capacitor for stabilizing the input
between the VIN pin and the VSS pin (CIN), the distance from the capacitors to these pins should be as short as
possible.
Note that generally the output voltage may increase when a series regulator is used at low load current (1.0 mA or
less).
Note that generally the output voltage may increase due to the leakage current from an output driver when a series
regulator is used at high temperature.
Note that the output voltage may increase due to the leakage current from an output driver even if the ON / OFF pin is
at OFF level when a series regulator is used at high temperature.
Generally a series regulator may cause oscillation, depending on the selection of external parts. The following
conditions are recommended for the S-1335 Series. However, be sure to perform sufficient evaluation under the actual
usage conditions for selection, including evaluation of temperature characteristics. Refer to "6. Example of
equivalent series resistance vs. Output current characteristics (Ta = 25C)" in " Reference Data" for the
equivalent series resistance (RESR) of the output capacitor.
Input capacitor (CIN):
Output capacitor (CL):
1.0 F or more
1.0 F or more
The voltage regulator may oscillate when the impedance of the power supply is high and the input capacitance is small
or an input capacitor is not connected.
If the output capacitance is small, power supply's fluctuation and the characteristics of load fluctuation become worse.
Sufficiently evaluate the output voltage's fluctuation with the actual device.
Overshoot may occur in the output voltage momentarily if the voltage is rapidly raised at power-on or when the power
supply fluctuates. Sufficiently evaluate the output voltage at power-on with the actual device.
The application conditions for the input voltage, the output voltage, and the load current should not exceed the
package power dissipation.
Do not apply an electrostatic discharge to this IC that exceeds the performance ratings of the built-in electrostatic
protection circuit.
In determining the output current, attention should be paid to the output current value specified in Table 20 and
Table 21 in " Electrical Characteristics" and footnote *5 of the table.
ABLIC Inc. claims no responsibility for any disputes arising out of or in connection with any infringement by products
including this IC of patents owned by a third party.
38
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
Characteristics (Typical Data)
1. Output voltage vs. Output current (When load current increases) (Ta = 25°C)
1. 1 VOUT = 1.0 V
1. 2 VOUT = 2.5 V
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
2.8
2.4
2.0
1.6
1.2
0.8
0.4
0
V
IN = 5.5 V
V
V
V
IN = 3.0 V
IN = 3.5 V
IN = 4.5 V
V
V
IN = 2.0 V
IN = 3.0 V
V
IN = 5.5 V
V
IN = 1.5 V
0
50 100 150 200 250 300 350 400
0
50 100 150 200 250 300 350 400
IOUT [mA]
IOUT [mA]
1. 3 VOUT = 3.6 V
4.0
3.6
3.2
2.8
2.4
2.0
1.6
1.2
0.8
0.4
0
V
V
V
IN = 4.1 V
IN = 4.6 V
IN = 5.5 V
Remark In determining the output current, attention should
be paid to the following.
1. The minimum output current value and footnote
*5 in Table 20 and Table 21 in " Electrical
Characteristics"
2. The package power dissipation
0
50 100 150 200 250 300 350 400
IOUT [mA]
2. Output voltage vs. Input voltage (Ta = 25°C)
2. 1 VOUT = 1.0 V
2. 2 VOUT = 2.5 V
1.4
1.2
1.0
3.0
2.5
2.0
I
I
I
OUT = 100 mA
OUT = 30 mA
OUT = 1 mA
0.8
0.6
0.4
0.2
0
I
I
OUT = 100 mA
OUT = 30 mA
1.5
1.0
0.5
0
IOUT = 1 mA
I
OUT = 100 μA
IOUT = 100 μA
0
1
2
3
4
5
6
0
1
2
3
4
5
6
VIN [V]
VIN [V]
2. 3 VOUT = 3.6 V
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
I
OUT = 100 mA
IOUT = 30 mA
I
I
OUT = 1 mA
OUT = 100 μA
0
1
2
3
4
5
6
VIN [V]
39
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
3. Dropout voltage vs. Output current
3. 1 VOUT = 1.0 V
3. 2 VOUT = 2.5 V
0.40
0.35
0.40
0.35
0.30
0.25
0.20
0.15
0.10
0.05
0
Ta = +85°C
0.30
0.25
0.20
0.15
0.10
0.05
0
Ta =
+
25°C
Ta = +85°C
Ta = −40°C
Ta =
+
25°C
Ta = −40°C
0
25
50
75
100 125 150
0
25
50
75
100 125 150
IOUT [mA]
IOUT [mA]
3. 3 VOUT = 3.6 V
0.40
0.35
0.30
0.25
0.20
0.15
0.10
0.05
0
Ta =
25°C
Ta = −40°C
+85°C
Ta =
+
0
25
50
75
100 125 150
I
OUT [mA]
4. Dropout voltage vs. Set output voltage
0.40
0.35
0.30
0.25
0.20
0.15
0.10
0.05
0
I
OUT = 150 mA
OUT = 100 mA
OUT = 30 mA
OUT = 10 mA
1 mA
I
I
I
I
OUT
=
1.0
1.6
2.2
2.8
3.4
4.0
VOUT(S) [V]
40
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
5. Output voltage vs. Ambient temperature
5. 1 VOUT = 1.0 V
5. 2 VOUT = 2.5 V
1.10
2.7
1.05
1.00
0.95
0.90
2.6
2.5
2.4
2.3
−40 −25
0
25
50
75 85
−40 −25
0
25
50
75 85
Ta [°C]
Ta [°C]
5. 3 VOUT = 3.6 V
3.8
3.7
3.6
3.5
3.4
3.3
3.2
−40 −25
0
25
50
75 85
Ta [°C]
6. Current consumption vs. Input voltage
6. 1 VOUT = 1.0 V
6. 2 VOUT = 2.5 V
40
35
30
25
40
35
30
25
20
15
10
5
Ta = −40°C
Ta = 25°C
85°C
+
Ta = −40°C
20
Ta =
+
Ta =
+25°C
15
10
5
Ta =
+
85°C
0
0
0
1
2
3
4
5
6
0
1
2
3
4
5
6
VIN [V]
VIN [V]
6. 3 VOUT = 3.6 V
40
35
30
25
20
15
10
5
Ta = −40°C
Ta =
+
25°C
Ta =
+
85°C
0
0
1
2
3
4
5
6
VIN [V]
41
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
7. Ripple rejection (Ta = 25°C)
7. 1 VOUT = 1.0 V
7. 2 VOUT = 2.5 V
VIN = 2.0 V, CL = 1.0 F
VIN = 3.5 V, CL = 1.0 F
120
100
80
60
40
20
0
120
100
80
60
I
I
I
I
OUT = 1 mA
I
I
I
I
OUT = 1 mA
OUT = 30 mA
OUT = 100 mA
OUT = 150 mA
OUT = 30 mA
OUT = 100 mA
OUT = 150 mA
40
20
0
10
100
1k
10k
100k
1M
10
100
1k
10k
100k
1M
Frequency [Hz]
Frequency [Hz]
7. 3 VOUT = 3.6 V
VIN = 4.6 V, CL = 1.0 F
120
100
80
60
I
I
I
I
OUT = 1 mA
40
20
0
OUT = 30 mA
OUT = 100 mA
OUT = 150 mA
10
100
1k
10k
100k
1M
Frequency [Hz]
42
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
Reference Data
1. Transient response characteristics when input (Ta = 25°C)
1. 1 VOUT = 1.0 V
IOUT = 30 mA, CIN = CL = 1.0 F,
IN = 2.0 V 3.0 V, tr = tf = 5.0 s
1. 2 VOUT = 2.5 V
IOUT = 30 mA, CIN = CL = 1.0 F,
IN = 3.5 V 4.5 V, tr = tf = 5.0 s
V
V
3.5
3.0
2.5
2.0
1.5
1.0
0.5
6.0
5.0
4.0
3.0
2.0
1.0
0
1.20
1.15
1.10
1.05
1.00
0.95
0.90
2.70
2.65
2.60
2.55
2.50
2.45
2.40
V
IN
V
IN
OUT
V
OUT
V
−100 −50
0
50 100 150 200 250
−100 −50
0
50 100 150 200 250
t [μs]
t [μs]
1. 3 VOUT = 3.6 V
IOUT = 30 mA, CIN = CL = 1.0 F,
IN = 4.6 V 5.5 V, tr = tf = 5.0 s
V
6.0
5.0
4.0
3.0
2.0
1.0
0
3.80
3.75
3.70
3.65
3.60
3.55
3.50
V
V
IN
OUT
−100 −50
0
50 100 150 200 250
t [μs]
43
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
2. Transient response characteristics of load (Ta = 25°C)
2. 1 VOUT = 1.0 V
VIN = 2.0 V, CIN = CL = 1.0 F, IOUT = 50 mA 100 mA
VIN = 2.0 V, CIN = CL = 1.0 F, IOUT = 1 mA 150 mA
200
100
0
200
100
0
1.20
1.15
1.10
1.05
1.00
0.95
0.90
1.40
1.30
1.20
1.10
1.00
0.90
0.80
I
OUT
I
OUT
−100
−200
−300
−400
−100
−200
−300
−400
V
OUT
V
OUT
−100 −50
0
50 100 150 200 250
−100 −50
0
50 100 150 200 250
t [μs]
t [μs]
2. 2 VOUT = 2.5 V
VIN = 3.5 V, CIN = CL = 1.0 F, IOUT = 50 mA 100 mA
VIN = 3.5 V, CIN = CL = 1.0 F, IOUT = 1 mA 150 mA
200
100
0
200
100
0
2.70
2.65
2.60
2.55
2.50
2.45
2.40
2.90
2.80
2.70
2.60
2.50
2.40
2.30
I
OUT
I
OUT
−100
−200
−300
−400
−100
−200
−300
−400
V
OUT
V
OUT
−100 −50
0
50 100 150 200 250
−100 −50
0
50 100 150 200 250
t [μs]
t [μs]
2. 3 VOUT = 3.6 V
VIN = 4.6 V, CIN = CL = 1.0 F, IOUT = 50 mA 100 mA
VIN = 4.6 V, CIN = CL = 1.0 F, IOUT = 1 mA 150 mA
200
100
0
200
100
0
3.80
3.75
3.70
3.65
3.60
3.55
3.50
4.00
3.90
3.80
3.70
3.60
3.50
3.40
I
OUT
I
OUT
−100
−200
−300
−400
−100
−200
−300
−400
V
OUT
V
OUT
−100 −50
0
50 100 150 200 250
−100 −50
0
50 100 150 200 250
t [μs]
t [μs]
44
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
3. Transient response characteristics of ON / OFF pin (Ta = 25°C)
3. 1 VOUT = 1.0 V
3. 1. 1
VIN = 2.0 V, CIN = CL = 1.0 F, IOUT = 100 mA,
ON / OFF = 0 V 2.0 V, tr = 1.0 s
t
SS = 0.1 ms
3. 1. 2 tSS = 1.0 ms
VIN = 2.0 V, CIN = CL = 1.0 F, IOUT = 100 mA,
V
VON / OFF = 0 V 2.0 V, tr = 1.0 s
5
4
3
2
1
0
5
4
3
2
1
0
6
6
4
4
V
ON / OFF
V
ON / OFF
2
2
0
0
VOUT
V
OUT
−2
−4
−2
−4
0
40
80
120
t [μs]
160
200
0
400
800
1200 1600 2000
t [μs]
3. 2 VOUT = 2.5 V
3. 2. 1 SS = 0.1 ms
t
3. 2. 2 tSS = 1.0 ms
VIN = 3.5 V, CIN = CL = 1.0 F, IOUT = 100 mA,
ON / OFF = 0 V 3.5 V, tr = 1.0 s
VIN = 3.5 V, CIN = CL = 1.0 F, IOUT = 100 mA,
ON / OFF = 0 V 3.5 V, tr = 1.0 s
V
V
5
4
3
2
1
0
5
4
3
2
1
0
6
6
V
ON / OFF
V
ON / OFF
4
4
2
2
V
OUT
V
OUT
0
0
−2
−4
−2
−4
0
40
80
120
t [μs]
160
200
0
400
800
1200 1600 2000
t [μs]
3. 3 VOUT = 3.6 V
3. 3. 1 tSS = 0.1 ms
3. 3. 2 tSS = 1.0 ms
VIN = 4.6 V, CIN = CL = 1.0 F, IOUT = 100 mA,
ON / OFF = 0 V 4.6 V, tr = 1.0 s
VIN = 4.6 V, CIN = CL = 1.0 F, IOUT = 100 mA,
ON / OFF = 0 V 4.6 V, tr = 1.0 s
V
V
5
4
3
2
1
0
5
4
3
2
1
0
6
6
V
ON / OFF
V
ON / OFF
4
4
V
OUT
V
OUT
2
2
0
0
−2
−4
−2
−4
0
40
80
120
t [μs]
160
200
0
400
800
1200 1600 2000
t [μs]
45
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
4. Inrush current characteristics (Ta = 25°C)
4. 1 VOUT = 1.0 V
4. 1. 1 tSS = 0.1 ms
4. 1. 2 tSS = 1.0 ms
VIN = 2.0 V, CIN = CL = 1.0 F, IOUT = 0.1 mA,
VIN = 2.0 V, CIN = CL = 1.0 F, IOUT = 0.1 mA,
VON / OFF = 0 V 2.0 V, tr = 1.0 s
VON / OFF = 0 V 2.0 V, tr = 1.0 s
6
4
6
4
500
400
500
400
V
ON / OFF
V
ON / OFF
2
2
300
200
100
0
300
200
100
0
VOUT
VOUT
0
0
−2
−4
−2
−4
I
OUT
IOUT
0
50
100
t [μs]
150
200
0
500
1000
1500
2000
t [μs]
4. 2 VOUT = 2.5 V
4. 2. 1 tSS = 0.1 ms
4. 2. 2 tSS = 1.0 ms
VIN = 3.5 V, CIN = CL = 1.0 F, IOUT = 0.1 mA,
VIN = 3.5 V, CIN = CL = 1.0 F, IOUT = 0.1 mA,
VON / OFF = 0 V 3.5 V, tr = 1.0 s
VON / OFF = 0 V 3.5 V, tr = 1.0 s
6
4
500
6
4
500
VON / OFF
V
ON / OFF
400
400
300
200
100
0
2
300
2
VOUT
VOUT
0
200
0
−2
−4
100
−2
−4
IOUT
IOUT
0
0
50
100
150
200
0
500
1000
1500
2000
t [μs]
t [μs]
4. 3 VOUT = 3.6 V
4. 3. 1 tSS = 0.1 ms
4. 3. 2 tSS = 1.0 ms
VIN = 4.6 V, CIN = CL = 1.0 F, IOUT = 0.1 mA,
VIN = 4.6 V, CIN = CL = 1.0 F, IOUT = 0.1 mA,
VON / OFF = 0 V 4.6 V, tr = 1.0 s
VON / OFF = 0 V 4.6 V, tr = 1.0 s
6
4
6
4
500
500
V
ON / OFF
400
300
200
100
0
400
300
200
100
0
V
ON / OFF
VOUT
2
2
V
OUT
0
0
−2
−4
−2
−4
I
OUT
I
OUT
0
50
100
t [μs]
150
200
0
500
1000
1500
2000
t [μs]
46
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
5. Output capacitance vs. Characteristics of discharge time (Ta = 25°C)
1.0 s
VIN = VOUT 1.0 V, IOUT = no load,
VON / OFF = VOUT 1.0 V VSS, tf = 1.0 s
VON / OFF
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
V
OUT(S) = 1.0 V
OUT(S) = 2.5 V
V
V
OUT(S) = 3.6 V
VSS
tDSC
VOUT
0
2
4
6
8
10
12
VOUT 10%
CL [μF]
VIN = VOUT 1.0 V
VON / OFF = VOUT 1.0 V VSS
Figure 37 S-1335 Series A / B / E / F / J / K Type
(With Discharge Shunt Function)
Figure 38 Test Condition of Discharge Time
6. Example of equivalent series resistance vs. Output current characteristics (Ta = 25C)
CIN = CL = 1.0 F
VIN
100
VOUT
CIN
S-1335 Series
*1
CL
Stable
SST*2
ON / OFF
VSS
RESR
0
0.1
150
I
OUT [mA]
*1. CL: TDK Corporation C1608X7R1C105K (1.0 F)
*2. S-1335 Series J / K / L / M type only.
Figure 39
Figure 40
47
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
Marking Specifications
1. SOT-23-5
Top view
Product code (Refer to Product name vs. Product code)
Lot number
(1) to (3):
(4):
5
4
(1) (2) (3) (4)
1
2
3
Product name vs. Product code
1. 1 S-1335 Series J type
1. 2 S-1335 Series K type
Product Code
Product Code
Product Name
Product Name
(1)
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
(2)
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
(3)
A
B
C
D
E
F
(1)
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
(2)
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
(3)
A
B
C
D
E
F
S-1335J10-M5T1U3
S-1335J11-M5T1U3
S-1335J12-M5T1U3
S-1335J13-M5T1U3
S-1335J14-M5T1U3
S-1335J15-M5T1U3
S-1335J16-M5T1U3
S-1335J17-M5T1U3
S-1335J18-M5T1U3
S-1335J19-M5T1U3
S-1335J20-M5T1U3
S-1335J21-M5T1U3
S-1335J22-M5T1U3
S-1335J23-M5T1U3
S-1335J24-M5T1U3
S-1335J25-M5T1U3
S-1335J26-M5T1U3
S-1335J27-M5T1U3
S-1335J28-M5T1U3
S-1335J2J-M5T1U3
S-1335J29-M5T1U3
S-1335J30-M5T1U3
S-1335J31-M5T1U3
S-1335J32-M5T1U3
S-1335J33-M5T1U3
S-1335J34-M5T1U3
S-1335J35-M5T1U3
S-1335J36-M5T1U3
S-1335K10-M5T1U3
S-1335K11-M5T1U3
S-1335K12-M5T1U3
S-1335K13-M5T1U3
S-1335K14-M5T1U3
S-1335K15-M5T1U3
S-1335K16-M5T1U3
S-1335K17-M5T1U3
S-1335K18-M5T1U3
S-1335K19-M5T1U3
S-1335K20-M5T1U3
S-1335K21-M5T1U3
S-1335K22-M5T1U3
S-1335K23-M5T1U3
S-1335K24-M5T1U3
S-1335K25-M5T1U3
S-1335K26-M5T1U3
S-1335K27-M5T1U3
S-1335K28-M5T1U3
S-1335K2J-M5T1U3
S-1335K29-M5T1U3
S-1335K30-M5T1U3
S-1335K31-M5T1U3
S-1335K32-M5T1U3
S-1335K33-M5T1U3
S-1335K34-M5T1U3
S-1335K35-M5T1U3
S-1335K36-M5T1U3
G
H
J
G
H
J
K
L
K
L
N
O
P
Q
R
S
T
N
O
P
Q
R
S
T
U
7
U
7
V
X
Y
Z
V
X
Y
Z
1
1
2
2
3
3
4
4
48
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
1. 3 S-1335 Series L type
1. 4 S-1335 Series M type
Product Code
Product Code
Product Name
Product Name
(1)
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
(2)
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
(3)
A
B
C
D
E
F
(1)
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
(2)
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
(3)
A
B
C
D
E
F
S-1335L10-M5T1U3
S-1335L11-M5T1U3
S-1335L12-M5T1U3
S-1335L13-M5T1U3
S-1335L14-M5T1U3
S-1335L15-M5T1U3
S-1335L16-M5T1U3
S-1335L17-M5T1U3
S-1335L18-M5T1U3
S-1335L19-M5T1U3
S-1335L20-M5T1U3
S-1335L21-M5T1U3
S-1335L22-M5T1U3
S-1335L23-M5T1U3
S-1335L24-M5T1U3
S-1335L25-M5T1U3
S-1335L26-M5T1U3
S-1335L27-M5T1U3
S-1335L28-M5T1U3
S-1335L2J-M5T1U3
S-1335L29-M5T1U3
S-1335L30-M5T1U3
S-1335L31-M5T1U3
S-1335L32-M5T1U3
S-1335L33-M5T1U3
S-1335L34-M5T1U3
S-1335L35-M5T1U3
S-1335L36-M5T1U3
S-1335M10-M5T1U3
S-1335M11-M5T1U3
S-1335M12-M5T1U3
S-1335M13-M5T1U3
S-1335M14-M5T1U3
S-1335M15-M5T1U3
S-1335M16-M5T1U3
S-1335M17-M5T1U3
S-1335M18-M5T1U3
S-1335M19-M5T1U3
S-1335M20-M5T1U3
S-1335M21-M5T1U3
S-1335M22-M5T1U3
S-1335M23-M5T1U3
S-1335M24-M5T1U3
S-1335M25-M5T1U3
S-1335M26-M5T1U3
S-1335M27-M5T1U3
S-1335M28-M5T1U3
S-1335M2J-M5T1U3
S-1335M29-M5T1U3
S-1335M30-M5T1U3
S-1335M31-M5T1U3
S-1335M32-M5T1U3
S-1335M33-M5T1U3
S-1335M34-M5T1U3
S-1335M35-M5T1U3
S-1335M36-M5T1U3
G
H
J
G
H
J
K
L
K
L
N
O
P
Q
R
S
T
N
O
P
Q
R
S
T
U
7
U
7
V
X
Y
Z
V
X
Y
Z
1
1
2
2
3
3
4
4
49
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
2. SC-82AB
Top view
Product code (Refer to Product name vs. Product code)
(1) to (3):
4
3
(1) (2) (3)
1
2
Product name vs. Product code
2. 1 S-1335 Series A type
2. 2 S-1335 Series B type
Product Code
Product Code
Product Name
Product Name
(1)
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
(2)
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
(3)
A
B
C
D
E
F
(1)
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
(2)
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
(3)
A
B
C
D
E
F
S-1335A10-N4T1U3
S-1335A11-N4T1U3
S-1335A12-N4T1U3
S-1335A13-N4T1U3
S-1335A14-N4T1U3
S-1335A15-N4T1U3
S-1335A16-N4T1U3
S-1335A17-N4T1U3
S-1335A18-N4T1U3
S-1335A19-N4T1U3
S-1335A20-N4T1U3
S-1335A21-N4T1U3
S-1335A22-N4T1U3
S-1335A23-N4T1U3
S-1335A24-N4T1U3
S-1335A25-N4T1U3
S-1335A26-N4T1U3
S-1335A27-N4T1U3
S-1335A28-N4T1U3
S-1335A2J-N4T1U3
S-1335A29-N4T1U3
S-1335A30-N4T1U3
S-1335A31-N4T1U3
S-1335A32-N4T1U3
S-1335A33-N4T1U3
S-1335A34-N4T1U3
S-1335A35-N4T1U3
S-1335A36-N4T1U3
S-1335B10-N4T1U3
S-1335B11-N4T1U3
S-1335B12-N4T1U3
S-1335B13-N4T1U3
S-1335B14-N4T1U3
S-1335B15-N4T1U3
S-1335B16-N4T1U3
S-1335B17-N4T1U3
S-1335B18-N4T1U3
S-1335B19-N4T1U3
S-1335B20-N4T1U3
S-1335B21-N4T1U3
S-1335B22-N4T1U3
S-1335B23-N4T1U3
S-1335B24-N4T1U3
S-1335B25-N4T1U3
S-1335B26-N4T1U3
S-1335B27-N4T1U3
S-1335B28-N4T1U3
S-1335B2J-N4T1U3
S-1335B29-N4T1U3
S-1335B30-N4T1U3
S-1335B31-N4T1U3
S-1335B32-N4T1U3
S-1335B33-N4T1U3
S-1335B34-N4T1U3
S-1335B35-N4T1U3
S-1335B36-N4T1U3
G
H
J
G
H
J
K
L
K
L
N
O
P
Q
R
S
T
N
O
P
Q
R
S
T
U
7
U
7
V
X
Y
Z
V
X
Y
Z
1
1
2
2
3
3
4
4
50
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
2. 3 S-1335 Series C type
2. 4 S-1335 Series D type
Product Code
Product Code
Product Name
Product Name
(1)
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
(2)
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
(3)
A
B
C
D
E
F
(1)
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
(2)
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
(3)
A
B
C
D
E
F
S-1335C10-N4T1U3
S-1335C11-N4T1U3
S-1335C12-N4T1U3
S-1335C13-N4T1U3
S-1335C14-N4T1U3
S-1335C15-N4T1U3
S-1335C16-N4T1U3
S-1335C17-N4T1U3
S-1335C18-N4T1U3
S-1335C19-N4T1U3
S-1335C20-N4T1U3
S-1335C21-N4T1U3
S-1335C22-N4T1U3
S-1335C23-N4T1U3
S-1335C24-N4T1U3
S-1335C25-N4T1U3
S-1335C26-N4T1U3
S-1335C27-N4T1U3
S-1335C28-N4T1U3
S-1335C2J-N4T1U3
S-1335C29-N4T1U3
S-1335C30-N4T1U3
S-1335C31-N4T1U3
S-1335C32-N4T1U3
S-1335C33-N4T1U3
S-1335C34-N4T1U3
S-1335C35-N4T1U3
S-1335C36-N4T1U3
S-1335D10-N4T1U3
S-1335D11-N4T1U3
S-1335D12-N4T1U3
S-1335D13-N4T1U3
S-1335D14-N4T1U3
S-1335D15-N4T1U3
S-1335D16-N4T1U3
S-1335D17-N4T1U3
S-1335D18-N4T1U3
S-1335D19-N4T1U3
S-1335D20-N4T1U3
S-1335D21-N4T1U3
S-1335D22-N4T1U3
S-1335D23-N4T1U3
S-1335D24-N4T1U3
S-1335D25-N4T1U3
S-1335D26-N4T1U3
S-1335D27-N4T1U3
S-1335D28-N4T1U3
S-1335D2J-N4T1U3
S-1335D29-N4T1U3
S-1335D30-N4T1U3
S-1335D31-N4T1U3
S-1335D32-N4T1U3
S-1335D33-N4T1U3
S-1335D34-N4T1U3
S-1335D35-N4T1U3
S-1335D36-N4T1U3
G
H
J
G
H
J
K
L
K
L
N
O
P
Q
R
S
T
N
O
P
Q
R
S
T
U
7
U
7
V
X
Y
Z
V
X
Y
Z
1
1
2
2
3
3
4
4
51
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
3. HSNT-4 (1010)
Top view
4
Product code (Refer to Product name vs. Product code)
Lot number
(1) to (3):
(4), (5):
3
(1) (2) (3)
(4) (5)
1
2
Product name vs. Product code
3. 1 S-1335 Series A type
3. 2 S-1335 Series B type
Product Code
Product Code
Product Name
Product Name
(1)
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
(2)
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
(3)
A
B
C
D
E
F
(1)
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
(2)
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
(3)
A
B
C
D
E
F
S-1335A10-A4T2U3
S-1335A11-A4T2U3
S-1335A12-A4T2U3
S-1335A13-A4T2U3
S-1335A14-A4T2U3
S-1335A15-A4T2U3
S-1335A16-A4T2U3
S-1335A17-A4T2U3
S-1335A18-A4T2U3
S-1335A19-A4T2U3
S-1335A20-A4T2U3
S-1335A21-A4T2U3
S-1335A22-A4T2U3
S-1335A23-A4T2U3
S-1335A24-A4T2U3
S-1335A25-A4T2U3
S-1335B10-A4T2U3
S-1335B11-A4T2U3
S-1335B12-A4T2U3
S-1335B13-A4T2U3
S-1335B14-A4T2U3
S-1335B15-A4T2U3
S-1335B16-A4T2U3
S-1335B17-A4T2U3
S-1335B18-A4T2U3
S-1335B19-A4T2U3
S-1335B20-A4T2U3
S-1335B21-A4T2U3
S-1335B22-A4T2U3
S-1335B23-A4T2U3
S-1335B24-A4T2U3
S-1335B25-A4T2U3
G
H
J
G
H
J
K
L
K
L
N
O
P
Q
R
S
T
N
O
P
Q
R
S
T
S-1335A26-A4T2U3
S-1335A27-A4T2U3
S-1335A28-A4T2U3
S-1335B26-A4T2U3
S-1335B27-A4T2U3
S-1335B28-A4T2U3
U
7
U
7
S-1335A2J-A4T2U3
S-1335A29-A4T2U3
S-1335A30-A4T2U3
S-1335A31-A4T2U3
S-1335A32-A4T2U3
S-1335A33-A4T2U3
S-1335A34-A4T2U3
S-1335A35-A4T2U3
S-1335A36-A4T2U3
S-1335B2J-A4T2U3
S-1335B29-A4T2U3
S-1335B30-A4T2U3
S-1335B31-A4T2U3
S-1335B32-A4T2U3
S-1335B33-A4T2U3
S-1335B34-A4T2U3
S-1335B35-A4T2U3
S-1335B36-A4T2U3
V
X
Y
Z
V
X
Y
Z
1
1
2
2
3
3
4
4
52
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
3. 3 S-1335 Series C type
3. 4 S-1335 Series D type
Product Code
Product Code
Product Name
Product Name
(1)
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
(2)
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
(3)
A
B
C
D
E
F
(1)
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
(2)
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
(3)
A
B
C
D
E
F
S-1335C10-A4T2U3
S-1335C11-A4T2U3
S-1335C12-A4T2U3
S-1335C13-A4T2U3
S-1335C14-A4T2U3
S-1335C15-A4T2U3
S-1335C16-A4T2U3
S-1335C17-A4T2U3
S-1335C18-A4T2U3
S-1335C19-A4T2U3
S-1335C20-A4T2U3
S-1335C21-A4T2U3
S-1335C22-A4T2U3
S-1335C23-A4T2U3
S-1335C24-A4T2U3
S-1335C25-A4T2U3
S-1335D10-A4T2U3
S-1335D11-A4T2U3
S-1335D12-A4T2U3
S-1335D13-A4T2U3
S-1335D14-A4T2U3
S-1335D15-A4T2U3
S-1335D16-A4T2U3
S-1335D17-A4T2U3
S-1335D18-A4T2U3
S-1335D19-A4T2U3
S-1335D20-A4T2U3
S-1335D21-A4T2U3
S-1335D22-A4T2U3
S-1335D23-A4T2U3
S-1335D24-A4T2U3
S-1335D25-A4T2U3
G
H
J
G
H
J
K
L
K
L
N
O
P
Q
R
S
T
N
O
P
Q
R
S
T
S-1335C26-A4T2U3
S-1335C27-A4T2U3
S-1335C28-A4T2U3
S-1335D26-A4T2U3
S-1335D27-A4T2U3
S-1335D28-A4T2U3
U
7
U
7
S-1335C2J-A4T2U3
S-1335C29-A4T2U3
S-1335C30-A4T2U3
S-1335C31-A4T2U3
S-1335C32-A4T2U3
S-1335C33-A4T2U3
S-1335C34-A4T2U3
S-1335C35-A4T2U3
S-1335C36-A4T2U3
S-1335D2J-A4T2U3
S-1335D29-A4T2U3
S-1335D30-A4T2U3
S-1335D31-A4T2U3
S-1335D32-A4T2U3
S-1335D33-A4T2U3
S-1335D34-A4T2U3
S-1335D35-A4T2U3
S-1335D36-A4T2U3
V
X
Y
Z
V
X
Y
Z
1
1
2
2
3
3
4
4
53
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
3. 5 S-1335 Series E type
3. 6 S-1335 Series F type
Product Code
Product Code
(2)
Product Name
Product Name
(1)
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
(2)
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
(3)
A
B
C
D
E
F
(1)
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
(3)
A
B
C
D
E
F
S-1335E10-A4T2U3
S-1335E11-A4T2U3
S-1335E12-A4T2U3
S-1335E13-A4T2U3
S-1335E14-A4T2U3
S-1335E15-A4T2U3
S-1335E16-A4T2U3
S-1335E17-A4T2U3
S-1335E18-A4T2U3
S-1335E19-A4T2U3
S-1335E20-A4T2U3
S-1335E21-A4T2U3
S-1335E22-A4T2U3
S-1335E23-A4T2U3
S-1335E24-A4T2U3
S-1335E25-A4T2U3
S-1335F10-A4T2U3
S-1335F11-A4T2U3
S-1335F12-A4T2U3
S-1335F13-A4T2U3
S-1335F14-A4T2U3
S-1335F15-A4T2U3
S-1335F16-A4T2U3
S-1335F17-A4T2U3
S-1335F18-A4T2U3
S-1335F19-A4T2U3
S-1335F20-A4T2U3
S-1335F21-A4T2U3
S-1335F22-A4T2U3
S-1335F23-A4T2U3
S-1335F24-A4T2U3
S-1335F25-A4T2U3
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
G
H
J
G
H
J
K
L
K
L
N
O
P
Q
R
S
T
N
O
P
Q
R
S
T
S-1335E26-A4T2U3
S-1335E27-A4T2U3
S-1335E28-A4T2U3
S-1335F26-A4T2U3
S-1335F27-A4T2U3
S-1335F28-A4T2U3
U
7
U
7
S-1335E2J-A4T2U3
S-1335E29-A4T2U3
S-1335E30-A4T2U3
S-1335E31-A4T2U3
S-1335E32-A4T2U3
S-1335E33-A4T2U3
S-1335E34-A4T2U3
S-1335E35-A4T2U3
S-1335E36-A4T2U3
S-1335F2J-A4T2U3
S-1335F29-A4T2U3
S-1335F30-A4T2U3
S-1335F31-A4T2U3
S-1335F32-A4T2U3
S-1335F33-A4T2U3
S-1335F34-A4T2U3
S-1335F35-A4T2U3
S-1335F36-A4T2U3
V
X
Y
Z
V
X
Y
Z
1
1
2
2
3
3
4
4
54
HIGH RIPPLE-REJECTION SOFT-START FUNCTION CMOS VOLTAGE REGULATOR
Rev.1.3_02
S-1335 Series
3. 7 S-1335 Series G type
3. 8 S-1335 Series H type
Product Code
Product Code
Product Name
Product Name
(1)
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
(2)
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
(3)
A
B
C
D
E
F
(1)
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
(2)
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
(3)
A
B
C
D
E
F
S-1335G10-A4T2U3
S-1335G11-A4T2U3
S-1335G12-A4T2U3
S-1335G13-A4T2U3
S-1335G14-A4T2U3
S-1335G15-A4T2U3
S-1335G16-A4T2U3
S-1335G17-A4T2U3
S-1335G18-A4T2U3
S-1335G19-A4T2U3
S-1335G20-A4T2U3
S-1335G21-A4T2U3
S-1335G22-A4T2U3
S-1335G23-A4T2U3
S-1335G24-A4T2U3
S-1335G25-A4T2U3
S-1335H10-A4T2U3
S-1335H11-A4T2U3
S-1335H12-A4T2U3
S-1335H13-A4T2U3
S-1335H14-A4T2U3
S-1335H15-A4T2U3
S-1335H16-A4T2U3
S-1335H17-A4T2U3
S-1335H18-A4T2U3
S-1335H19-A4T2U3
S-1335H20-A4T2U3
S-1335H21-A4T2U3
S-1335H22-A4T2U3
S-1335H23-A4T2U3
S-1335H24-A4T2U3
S-1335H25-A4T2U3
G
H
J
G
H
J
K
L
K
L
N
O
P
Q
R
S
T
N
O
P
Q
R
S
T
S-1335G26-A4T2U3
S-1335G27-A4T2U3
S-1335G28-A4T2U3
S-1335H26-A4T2U3
S-1335H27-A4T2U3
S-1335H28-A4T2U3
U
7
U
7
S-1335G2J-A4T2U3
S-1335G29-A4T2U3
S-1335G30-A4T2U3
S-1335G31-A4T2U3
S-1335G32-A4T2U3
S-1335G33-A4T2U3
S-1335G34-A4T2U3
S-1335G35-A4T2U3
S-1335G36-A4T2U3
S-1335H2J-A4T2U3
S-1335H29-A4T2U3
S-1335H30-A4T2U3
S-1335H31-A4T2U3
S-1335H32-A4T2U3
S-1335H33-A4T2U3
S-1335H34-A4T2U3
S-1335H35-A4T2U3
S-1335H36-A4T2U3
V
X
Y
Z
V
X
Y
Z
1
1
2
2
3
3
4
4
55
2.9±0.2
1.9±0.2
4
5
+0.1
-0.06
1
2
3
0.16
0.95±0.1
0.4±0.1
No. MP005-A-P-SD-1.3
TITLE
SOT235-A-PKG Dimensions
MP005-A-P-SD-1.3
No.
ANGLE
UNIT
mm
ABLIC Inc.
4.0±0.1(10 pitches:40.0±0.2)
+0.1
-0
2.0±0.05
0.25±0.1
ø1.5
+0.2
-0
4.0±0.1
ø1.0
1.4±0.2
3.2±0.2
3
4
2 1
5
Feed direction
No. MP005-A-C-SD-2.1
TITLE
SOT235-A-Carrier Tape
MP005-A-C-SD-2.1
No.
ANGLE
UNIT
mm
ABLIC Inc.
12.5max.
9.0±0.3
Enlarged drawing in the central part
ø13±0.2
(60°)
(60°)
No. MP005-A-R-SD-1.1
TITLE
SOT235-A-Reel
MP005-A-R-SD-1.1
No.
ANGLE
UNIT
QTY.
3,000
mm
ABLIC Inc.
2.0±0.2
1.3±0.2
4
3
0.05
+0.1
-0.06
0.16
2
1
+0.1
-0.05
0.4
+0.1
-0.05
0.3
No. NP004-A-P-SD-2.0
TITLE
No.
SC82AB-A-PKG Dimensions
NP004-A-P-SD-2.0
ANGLE
UNIT
mm
ABLIC Inc.
2.0±0.05
+0.1
-0
1.1±0.1
ø1.5
4.0±0.1
4.0±0.1
0.2±0.05
ø1.05±0.1
(0.7)
2.2±0.2
2
3
1
4
Feed direction
No. NP004-A-C-SD-3.0
SC82AB-A-Carrier Tape
NP004-A-C-SD-3.0
TITLE
No.
ANGLE
UNIT
mm
ABLIC Inc.
1.1±0.1
+0.1
-0
2.0±0.1
4.0±0.1
ø1.5
0.2±0.05
4.0±0.1
ø1.05±0.1
2.3±0.15
2
3
1
4
Feed direction
No. NP004-A-C-S1-2.0
TITLE
SC82AB-A-Carrier Tape
NP004-A-C-S1-2.0
No.
ANGLE
UNIT
mm
ABLIC Inc.
12.5max.
9.0±0.3
Enlarged drawing in the central part
ø13±0.2
(60°)
(60°)
No. NP004-A-R-SD-1.1
TITLE
No.
SC82AB-A-Reel
NP004-A-R-SD-1.1
QTY.
ANGLE
UNIT
3,000
mm
ABLIC Inc.
0.38±0.02
0.65
3
4
+0.05
-0.02
1
2
0.08
1.00±0.04
he heat sink of back side has different electric
potential depending on the product.
Confirm specifications of each product.
Do not use it as the function of electrode.
0.20±0.05
No. PL004-A-P-SD-1.1
TITLE
HSNT-4-B-PKG Dimensions
PL004-A-P-SD-1.1
No.
ANGLE
UNIT
mm
ABLIC Inc.
4.0±0.05
2.0±0.05
+0.1
-0
ø1.5
0.25±0.05
+0.1
-0
ø0.5
2.0±0.05
0.5±0.05
1.12±0.05
2
3
1
4
Feed direction
No. PL004-A-C-SD-2.0
HSNT-4-B-Carrier Tape
PL004-A-C-SD-2.0
TITLE
No.
ANGLE
UNIT
mm
ABLIC Inc.
+1.0
- 0.0
9.0
11.4±1.0
Enlarged drawing in the central part
ø13±0.2
(60°)
(60°)
No. PL004-A-R-SD-1.0
HSNT-4-B-Reel
PL004-A-R-SD-1.0
TITLE
No.
QTY.
10,000
ANGLE
UNIT
mm
ABLIC Inc.
Land Pattern
0.30min.
0.38~0.48
0.38~0.48
0.07
0.65±0.02
(1.02)
Caution It is recommended to solder the heat sink to a board
in order to ensure the heat radiation.
PKG
Metal Mask Pattern
Aperture ratio
Aperture ratio
Caution
Mask aperture ratio of the lead mounting part is 100%.
Mask aperture ratio of the heat sink mounting part is 40%.
Mask thickness: t0.10mm to 0.12 mm
100%
40%
t0.10mm ~ 0.12 mm
HSNT-4-B
TITLE
-Land Recommendation
No. PL004-A-L-SD-2.0
No.
PL004-A-L-SD-2.0
ANGLE
UNIT
mm
ABLIC Inc.
Disclaimers (Handling Precautions)
1. All the information described herein (product data, specifications, figures, tables, programs, algorithms and application
circuit examples, etc.) is current as of publishing date of this document and is subject to change without notice.
2. The circuit examples and the usages described herein are for reference only, and do not guarantee the success of
any specific mass-production design.
ABLIC Inc. is not responsible for damages caused by the reasons other than the products described herein
(hereinafter "the products") or infringement of third-party intellectual property right and any other right due to the use
of the information described herein.
3. ABLIC Inc. is not responsible for damages caused by the incorrect information described herein.
4. Be careful to use the products within their specified ranges. Pay special attention to the absolute maximum ratings,
operation voltage range and electrical characteristics, etc.
ABLIC Inc. is not responsible for damages caused by failures and / or accidents, etc. that occur due to the use of the
products outside their specified ranges.
5. When using the products, confirm their applications, and the laws and regulations of the region or country where they
are used and verify suitability, safety and other factors for the intended use.
6. When exporting the products, comply with the Foreign Exchange and Foreign Trade Act and all other export-related
laws, and follow the required procedures.
7. The products must not be used or provided (exported) for the purposes of the development of weapons of mass
destruction or military use. ABLIC Inc. is not responsible for any provision (export) to those whose purpose is to
develop, manufacture, use or store nuclear, biological or chemical weapons, missiles, or other military use.
8. The products are not designed to be used as part of any device or equipment that may affect the human body, human
life, or assets (such as medical equipment, disaster prevention systems, security systems, combustion control
systems, infrastructure control systems, vehicle equipment, traffic systems, in-vehicle equipment, aviation equipment,
aerospace equipment, and nuclear-related equipment), excluding when specified for in-vehicle use or other uses. Do
not apply the products to the above listed devices and equipments without prior written permission by ABLIC Inc.
Especially, the products cannot be used for life support devices, devices implanted in the human body and devices
that directly affect human life, etc.
Prior consultation with our sales office is required when considering the above uses.
ABLIC Inc. is not responsible for damages caused by unauthorized or unspecified use of our products.
9. Semiconductor products may fail or malfunction with some probability.
The user of the products should therefore take responsibility to give thorough consideration to safety design including
redundancy, fire spread prevention measures, and malfunction prevention to prevent accidents causing injury or
death, fires and social damage, etc. that may ensue from the products' failure or malfunction.
The entire system must be sufficiently evaluated and applied on customer's own responsibility.
10. The products are not designed to be radiation-proof. The necessary radiation measures should be taken in the
product design by the customer depending on the intended use.
11. The products do not affect human health under normal use. However, they contain chemical substances and heavy
metals and should therefore not be put in the mouth. The fracture surfaces of wafers and chips may be sharp. Be
careful when handling these with the bare hands to prevent injuries, etc.
12. When disposing of the products, comply with the laws and ordinances of the country or region where they are used.
13. The information described herein contains copyright information and know-how of ABLIC Inc.
The information described herein does not convey any license under any intellectual property rights or any other
rights belonging to ABLIC Inc. or a third party. Reproduction or copying of the information from this document or any
part of this document described herein for the purpose of disclosing it to a third-party without the express permission
of ABLIC Inc. is strictly prohibited.
14. For more details on the information described herein, contact our sales office.
2.2-2018.06
www.ablic.com
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明