AD5347BRU-REEL7 [ADI]
2.5 V to 5.5 V, Parallel Interface 2.5 V to 5.5 V, Parallel Interface; 2.5 V至5.5 V ,并行接口2.5 V至5.5 V ,并行接口型号: | AD5347BRU-REEL7 |
厂家: | ADI |
描述: | 2.5 V to 5.5 V, Parallel Interface 2.5 V to 5.5 V, Parallel Interface |
文件: | 总24页 (文件大小:1184K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
2.5 V to 5.5 V, Parallel Interface
Octal Voltage Output 8-/10-/12-Bit DACs
AD5346/AD5347/AD5348
GENERAL DESCRIPTION
FEATURES
The AD5346/AD5347/AD53481 are octal 8-, 10-, and 12-bit
DACs, operating from a 2.5 V to 5.5 V supply. These devices
incorporate an on-chip output buffer that can drive the output
to both supply rails, and also allow a choice of buffered or
unbuffered reference input.
AD5346: octal 8-bit DAC
AD5347: octal 10-bit DAC
AD5348: octal 12-bit DAC
Low power operation: 1.4 mA (max) @ 3.6 V
Power-down to 120 nA @ 3 V, 400 nA @ 5 V
Guaranteed monotonic by design over all codes
Rail-to-rail output range: 0 V to VREF or 0 V to 2 × VREF
Power-on reset to 0 V
CS
The AD5346/AD5347/AD5348 have a parallel interface.
selects the device and data is loaded into the input registers on
WR
the rising edge of
. A readback feature allows the internal
LDAC
Simultaneous update of DAC outputs via
pin
DAC registers to be read back through the digital port.
CLR
Asynchronous
Readback
facility
The GAIN pin on these devices allows the output range to be
Buffered/unbuffered reference inputs
WR
38-lead TSSOP/6 mm × 6 mm 40-lead LFCSP packaging
Temperature range: –40°C to +105°C
set at 0 V to VREF or 0 V to 2 × VREF
Input data to the DACs is double-buffered, allowing simultane-
LDAC
.
20 ns
time
ous update of multiple DACs in a system using the
pin.
input is also provided, which resets the
CLR
An asynchronous
APPLICATIONS
contents of the input register and the DAC register to all zeros.
These devices also incorporate a power-on reset circuit that
ensures that the DAC output powers on to 0 V and remains
there until valid data is written to the device.
Portable battery-powered instruments
Digital gain and offset adjustment
Programmable voltage and current sources
Optical networking
Automatic test equipment
Mobile communications
Programmable attenuators
Industrial process control
All three parts are pin compatible, which allows users to select
the amount of resolution appropriate for their application
without redesigning their circuit board.
FUNCTIONAL BLOCK DIAGRAM
V
V
AB
V
CD
REF
AGND DGND
DD
REF
POWER-ON
RESET
AD5348
BUF
INPUT
REGISTER
DAC
REGISTER
STRING
DAC A
GAIN
BUFFER
V
A
B
OUT
DB11
INPUT
REGISTER
DAC
REGISTER
.
.
.
STRING
DAC B
BUFFER
BUFFER
V
OUT
DB0
INPUT
REGISTER
DAC
REGISTER
STRING
DAC C
V
C
OUT
INTER-
FACE
LOGIC
CS
DAC
REGISTER
INPUT
REGISTER
STRING
DAC D
V
D
BUFFER
BUFFER
OUT
RD
DAC
REGISTER
INPUT
REGISTER
STRING
DAC E
V
E
F
WR
OUT
DAC
REGISTER
INPUT
REGISTER
STRING
DAC F
V
OUT
A2
A1
A0
BUFFER
BUFFER
BUFFER
INPUT
REGISTER
DAC
REGISTER
STRING
DAC G
V
V
G
OUT
DAC
REGISTER
INPUT
REGISTER
STRING
DAC H
H
OUT
CLR
POWER-DOWN
LOGIC
LDAC
V
GH
V
EF
REF
PD
REF
Figure 1.
1Protected by U.S. Patent No. 5,969,657; other patents pending.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.326.8703
www.analog.com
© 2003 Analog Devices, Inc. All rights reserved.
AD5346/AD5347/AD5348
TABLE OF CONTENTS
Specifications..................................................................................... 3
Power-On Reset.......................................................................... 17
Power-Down Mode.................................................................... 17
Suggested Data Bus Formats..................................................... 18
Applications Information.............................................................. 19
Typical Application Circuits ..................................................... 19
Driving VDD from the Reference Voltage................................. 19
Bipolar Operation Using the AD5346/AD5347/AD5348..... 19
Decoding Multiple AD5346/AD5347/AD5348s.................... 20
AC Characteristics............................................................................ 4
Timing Characteristics..................................................................... 5
Absolute Maximum Ratings............................................................ 6
ESD Caution.................................................................................. 6
AD5346 Pin Configurations and Function Descriptions ........... 7
AD5347 Pin Configurations and Function Descriptions ........... 8
AD5348 Pin Configurations and Function Descriptions ........... 9
Terminology .................................................................................... 10
Typical Performance Characteristics ........................................... 12
Functional Description .................................................................. 16
Digital-to-Analog Section ......................................................... 16
Resistor String............................................................................. 16
DAC Reference Input................................................................. 16
Output Amplifier........................................................................ 16
Parallel Interface ......................................................................... 17
AD5346/AD5347/AD5348 as Digitally Programmable
Window Detectors ...................................................................... 20
Programmable Current Source ................................................ 20
Coarse and Fine Adjustment Using the
AD5346/AD5347/AD5348 ....................................................... 21
Power Supply Bypassing and Grounding................................ 21
Outline Dimensions....................................................................... 23
Ordering Guides......................................................................... 24
REVISION HISTORY
Revision 0: Initial Version
Rev. 0 | Page 2 of 24
AD5346/AD5347/AD5348
SPECIFICATIONS
Table 1. VDD = 2.5 V to 5.5 V; VREF = 2 V; RL = 2 kΩ to GND; CL = 200 pF to GND; all specifications TMIN to TMAX
,
unless otherwise noted
B Version1
Parameter2
DC PERFORMANCE3,4
Min
Typ
Max
Unit
Conditions/Comments
AD5346
Resolution
8
Bits
LSB
0.25 LSB
Relative Accuracy
Differential Nonlinearity
AD5347
0.15
0.02
1
Guaranteed monotonic by design over all codes
Guaranteed monotonic by design over all codes
Guaranteed monotonic by design over all codes
Resolution
10
0.5
0.05
Bits
LSB
LSB
Relative Accuracy
Differential Nonlinearity
AD5348
4
0.5
Resolution
12
2
0.2
0.4
0.1
10
10
–12
–5
–60
Bits
LSB
LSB
% of FSR
% of FSR
mV
Relative Accuracy
Differential Nonlinearity
Offset Error
16
1
3
1
60
Gain Error
Lower Deadband5
Upper Deadband5
Offset Error Drift6
Gain Error Drift6
Lower deadband exists only if offset error is negative
VDD = 5 V; upper deadband exists only if VREF = VDD
60
mV
ppm of FSR/°C
ppm of FSR/°C
dB
DC Power Supply Rejection
∆VDD = 10%
Ratio6
DC Crosstalk6
200
µV
RL = 2 kΩ to GND, 2 kΩ to VDD; CL = 200 pF to GND;
Gain = +1
DAC REFERENCE INPUT6
VREF Input Range
VREF Input Range
1
0.25
VDD
VDD
V
V
Buffered reference mode
Unbuffered reference mode
Buffered reference mode and power-down mode
Gain = +1; input impedance = RDAC
Gain = +2; input impedance = RDAC
Frequency = 10 kHz
VREF Input Impedance
>10
90
45
–90
–75
MΩ
kΩ
kΩ
dB
dB
Reference Feedthrough
Channel-to-Channel Isolation
OUTPUT CHARACTERISTICS6
Minimum Output Voltage4, 7
Maximum Output Voltage4, 7
Frequency = 10 kHz
0.001
V min
V max
Rail-to-rail operation
VDD
–
0.001
0.5
25
16
2.5
5
DC Output Impedance
Short Circuit Current
Ω
mA
mA
µs
VDD = 5 V
VDD = 3 V
Power-Up Time
Coming out of power-down mode; VDD = 5 V
Coming out of power-down mode; VDD = 3 V
µs
LOGIC INPUTS
6
Input Current
VIL, Input Low Voltage
1
0.8
0.7
0.6
µA
V
V
VDD = 5 V 10%
VDD = 3 V 10%
VDD = 2.5 V
V
VIH, Input High Voltage
Pin Capacitance
1.7
V
pF
VDD = 2.5 V to 5.5 V
5
Rev. 0 | Page 3 of 24
AD5346/AD5347/AD5348
B Version1
Typ
Parameter2
Min
Max
0.4
Unit
Conditions/Comments
LOGIC OUTPUTS6
VDD = 4.5 V to 5.5 V
Output Low Voltage, VOL
Output High Voltage, VOH
VDD = 2.5 V to 3.6 V
Output Low Voltage, VOL
Output High Voltage, VOH
POWER REQUIREMENTS
VDD
V
V
ISINK = 200 µA
ISOURCE = 200 µA
VDD – 1
0.4
V
V
ISINK = 200 µA
ISOURCE = 200 µA
VDD – 0.5
2.5
5.5
V
IDD (Normal Mode)
VDD = 4.5 V to 5.5 V
VDD = 2.5 V to 3.6 V
VIH = VDD, VIL = GND
All DACs in unbuffered mode. In buffered mode,
extra current is typically x µA per DAC, where x = 5 µA +
VREF/RDAC
1
0.8
1.65
1.4
mA
mA
IDD (Power-Down Mode)
VDD = 4.5 V to 5.5 V
VDD = 2.5 V to 3.6 V
VIH = VDD, VIL = GND
0.4
0.12
1
1
µA
µA
See footnotes after the AC Characteristics table.
AC CHARACTERISTICS6
Table 2. VDD = 2.5 V to 5.5 V; RL = 2 kΩ to GND; CL = 200 pF to GND; all specifications TMIN to TMAX, unless otherwise noted
B Version1
Min Typ
Parameter2
Output Voltage Settling Time
AD5346
Max
Unit
Conditions/Comments
VREF = 2 V
6
8
9
10
µs
µs
µs
1/4 scale to 3/4 scale change (40 H to C0 H)
1/4 scale to 3/4 scale change (100 H to 300 H)
1/4 scale to 3/4 scale change (400 H to C00 H)
AD5347
7
AD5348
8
Slew Rate
0.7
V/µs
Major Code Transition Glitch
Energy
8
nV-s
1 LSB change around major carry
Digital Feedthrough
Digital Crosstalk
Analog Crosstalk
DAC-to-DAC Crosstalk
Multiplying Bandwidth
Total Harmonic Distortion
0.5
1
1
3.5
200
–70
nV-s
nV-s
nV-s
nV-s
kHz
dB
VREF = 2 V 0.1 V p-p; unbuffered mode
VREF = 2. V 0.1 V p-p; frequency = 10 kHz; unbuffered mode
1 Temperature range: B Version: –40°C to +105°C; typical specifications are at 25°C.
2 See Terminology section.
3 Linearity is tested using a reduced code range: AD5346 (Code 8 to 255); AD5347 (Code 28 to 1023); AD5348 (Code 115 to 4095).
4 DC specifications tested with outputs unloaded.
5 This corresponds to x codes. x = deadband voltage/LSB size.
6 Guaranteed by design and characterization, not production tested.
7 For the amplifier output to reach its minimum voltage, offset error must be negative. For the amplifier output to reach its maximum voltage, VREF = VDD and
the offset plus gain error must be positive.
200µA
I
OL
TO OUTPUT
PIN
V
(min) + V (max)
OL
OH
C
50pF
L
2
200µA
I
OH
Figure 2. Load Circuit for Digital Output Timing Specifications
Rev. 0 | Page 4 of 24
AD5346/AD5347/AD5348
TIMING CHARACTERISTICS1, 2, 3
Table 3. VDD = 2.5 V to 5.5 V; all specifications TMIN to TMAX, unless otherwise noted
Parameter
Limit at TMIN, TMAX
Unit
Condition/Comments
Data Write Mode (Figure 3)
CS to WR setup time
CS to WR hold time
WR pulse width
Data, GAIN, BUF setup time
Data, GAIN, BUF hold time
Synchronous mode. WR falling to LDAC falling.
Synchronous mode. LDAC falling to WR rising.
t1
t2
t3
t4
t5
t6
t7
0
0
20
5
4.5
5
ns min
ns min
ns min
ns min
ns min
ns min
ns min
5
WR
rising to LDAC rising.
t8
4.5
ns min
Synchronous mode.
Asynchronous mode. LDAC rising to WR rising.
Asynchronous mode. WR rising to LDAC falling.
LDAC pulse width
t9
t10
t11
5
ns min
ns min
ns min
ns min
ns min
ns min
ns min
4.5
20
10
20
20
0
CLR
t12
t13
t14
t15
pulse width
Time between WR cycles
A0, A1, A2 setup time
A0, A1, A2 hold time
Data Readback Mode (Figure 4)
CS
t16
t17
0
0
ns min
ns min
ns min
ns min
ns min
ns min
ns max
ns max
ns min
ns max
ns max
ns max
ns min
ns min
ns min
ns min
A0, A1, A2 to setup time
CS
A0, A1, A2 to hold time
RD
CS to falling edge of
t18
t19
0
RD pulse width; VDD = 3.6 V to 5.5 V
RD pulse width; VDD = 2.5 V to 3.6 V
CS to RD hold time
Data access time after falling edge of RD; VDD = 3.6 V to 5.5 V
Data access time after falling edge of RD VDD = 2.5 V to 3.6 V
Bus relinquish time after rising edge of RD
20
30
0
22
30
4
30
22
30
30
30
30
50
t20
t21
t22
t23
CS falling edge to data; VDD = 3.6 V to 5.5 V
CS falling edge to data; VDD = 2.5 V to 3.6 V
RD
t24
t25
t26
Time between
cycles
Time from RD to WR
Time from WR to RD, VDD = 3.6 V to 5.5 V
Time from WR to RD, VDD = 2.5 V to 3.6 V
1 Guaranteed by design and characterization, not production tested.
2 All input signals are specified with tr = tf = 5 ns (10% to 90% of VDD) and timed from a voltage level of (VIL + VIH)/2.
3 See Figure 2.
t1
t2
CS
A0–A2
t3
t13
t17
t16
WR
t5
CS
t4
DATA,
GAIN, BUF
t18
t20
t19
t24
t6
t8
t7
t9
RD
DATA
WR
1
LDAC
t21
t22
t10
t11
2
LDAC
t23
t12
CLR
t25
t14
t15
A0–A2
t26
NOTES
1. SYNCHRONOUS LDAC UPDATE MODE
2. ASYNCHRONOUS LDAC UPDATE MODE
Figure 3. Parallel Interface Write Timing Diagram
Figure 4. Parallel Interface Read Timing Diagram
Rev. 0 | Page 5 of 24
AD5346/AD5347/AD5348
ABSOLUTE MAXIMUM RATINGS
Table 4. TA = 25°C, unless otherwise noted
Parameter
Rating
VDD to GND
–0.3 V to +7 V
Digital Input Voltage to GND
Digital Output Voltage to GND
Reference Input Voltage to GND
VOUT to GND
–0.3 V to VDD + 0.3 V
–0.3 V to VDD + 0.3 V
–0.3 V to VDD + 0.3 V
–0.3 V to VDD + 0.3 V
Operating Temperature Range
Industrial (B Version)
Storage Temperature Range
Junction Temperature
38-Lead TSSOP Package
Power Dissipation
θJA Thermal Impedance
θJC Thermal Impedance
40-Lead LFCSP Package
Power Dissipation
–40°C to +105°C
–65°C to +150°C
150°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those listed in the operational sections
of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
(TJ max − TA)/ θJA mW
98.3°C/W
8.9°C/W
(TJ max − TA)/ θJA mW
29.6°C/W
θJA Thermal Impedance (3-layer
board)
Lead Temperature, Soldering (10 sec)
IR Reflow, Peak Temperature
300°C
220°C
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. 0 | Page 6 of 24
AD5346/AD5347/AD5348
AD5346 PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
V
GH
EF
1
38
37
36
35
34
33
32
31
30
PD
REF
V
2
CLR
REF
V
V
CD
3
REF
40 39 38 37 36 35 34 33 32 31
GAIN
WR
4
V
V
V
V
V
A
B
C
D
1
2
30
29
28
27
26
25
24
23
22
21
DD
AB
A
OUT
OUT
OUT
OUT
RD
CS
DB
DB
DB
DB
DB
DB
DB
DB
5
REF
RD
CS
V
6
OUT
8-BIT
3
7
6
5
4
3
2
1
0
AD5346
TOP VIEW
(Not to Scale)
V
V
V
B
C
D
7
DB
7
OUT
OUT
OUT
4
8-BIT
8
DB
6
5
4
5
AGND
AGND
AD5346
TOP VIEW
(Not to Scale)
9
DB
6
10
11
12
13
14
15
16
17
18
19
29 DB
28
AGND
V
E
F
7
OUT
DB
V
E
F
3
2
1
0
OUT
V
8
OUT
27 DB
V
OUT
V
G
9
OUT
DB
DB
26
25
V
G
OUT
V
H
10
OUT
V
H
OUT
11 12 13 14 15 16 17 18 19 20
DGND
BUF
24 DGND
23 DGND
DGND
DGND
22
21
LDAC
A0
Figure 6. AD5346 Pin Configuration—LFCSP
20 A2
A1
Figure 5. AD5346 Pin Configuration—TSSOP
Table 5. AD5346 Pin Function Descriptions
Pin Number
TSSOP
LFCSP
35
36
37
38, 39
Mnemonic
VREFGH
VREFEF
VREFCD
VDD
Function
1
2
3
4
Reference Input for DACs G and H.
Reference Input for DACs E and F.
Reference Input for DACs C and D.
Power Supply Pin(s). This part can operate from 2.5 V to 5.5 V, and the supply should be decoupled
with a 10 µF capacitor in parallel with a 0.1 µF capacitor to GND. Both VDD pins on the LFCSP
package must be at the same potential.
5
40
VREFAB
Reference Input for DACs A and B.
6–9,
1–4,
VOUTX
Output of DAC X. Buffered output with rail-to-rail operation.
11–14
7–10
10
15,
5, 6
11,
AGND
DGND
Analog Ground. Ground reference for analog circuitry.
Digital Ground. Ground reference for digital circuitry.
21–24
17–20
16
17
12
13
BUF
LDAC
Buffer Control Pin. Controls whether the reference input to the DAC is buffered or unbuffered.
Active Low Control Input. Updates the DAC registers with the contents of the input registers, which
allows all DAC outputs to be simultaneously updated.
18
19
14
15
A0
A1
LSB Address Pin. Selects which DAC is to be written to.
Address Pin. Selects which DAC is to be written to.
20
25–32
33
16
21–28
29
A2
DB0–DB7
CS
MSB Address Pin. Selects which DAC is to be written to.
Eight Parallel Data Inputs. DB7 is the MSB of these eight bits.
Active Low Chip Select Input. Used in conjunction with WR to write data to the parallel interface, or
with RD to read back data from a DAC.
34
35
36
37
38
30
31
32
33
34
RD
Active Low Read Input. Used in conjunction with CS to read data back from the internal DACs.
Active Low Write Input. Used in conjunction with CS to write data to the parallel interface.
Gain Control Pin. Controls whether the output range from the DAC is 0 V to VREF or 0 V to 2 × VREF.
Asynchronous Active Low Control Input. Clears all input registers and DAC registers to zeros.
Power-Down Pin. This active low control pin puts all DACs into power-down mode.
WR
GAIN
CLR
PD
Rev. 0 | Page 7 of 24
AD5346/AD5347/AD5348
AD5347 PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
V
GH
EF
1
38
37
36
35
34
33
32
31
30
PD
REF
V
2
CLR
REF
V
V
CD
3
REF
40 39 38 37 36 35 34 33 32 31
GAIN
WR
4
V
V
V
V
V
A
B
C
D
1
2
30
29
28
27
26
25
24
23
22
21
DD
AB
A
OUT
OUT
OUT
OUT
RD
CS
DB
DB
DB
DB
DB
DB
DB
DB
5
REF
RD
CS
V
6
OUT
10-BIT
3
9
8
7
6
5
4
3
2
AD5347
TOP VIEW
(Not to Scale)
V
V
V
B
C
D
7
DB
9
OUT
OUT
OUT
4
10-BIT
8
DB
8
7
6
5
4
3
5
AGND
AGND
AD5347
TOP VIEW
(Not to Scale)
9
DB
6
10
11
12
13
14
15
16
17
18
19
29 DB
28
AGND
V
E
F
7
OUT
DB
27 DB
V
E
F
OUT
V
8
OUT
V
OUT
V
G
9
OUT
DB
DB
26
25
V
G
OUT
V
H
10
OUT
V
H
2
1
0
OUT
11 12 13 14 15 16 17 18 19 20
DGND
BUF
24 DB
23 DB
DGND
DGND
22
21
LDAC
A0
Figure 8. AD5347 Pin Configuration—LFCSP
20 A2
A1
Figure 7. AD5347 Pin Configuration—TSSOP
Table 6. AD5347 Pin Function Descriptions
Pin Number
TSSOP
LFCSP
35
36
37
38, 39
Mnemonic Function
1
2
3
4
VREFGH
VREFEF
VREFCD
VDD
Reference Input for DACs G and H.
Reference Input for DACs E and F.
Reference Input for DACs C and D.
Power Supply Pin(s). This part can operate from 2.5 V to 5.5 V, and the supply should be decoupled
with a 10 µF capacitor in parallel with a 0.1 µF capacitor to GND. Both VDD pins on the LFCSP package
must be at the same potential.
5
40
VREFAB
Reference Input for DACs A and B.
6–9,
1–4,
VOUTX
Output of DAC X. Buffered output with rail-to-rail operation.
11–14
7–10
10
15, 21–22
5, 6
11,
AGND
DGND
Analog Ground. Ground reference for analog circuitry.
Digital Ground. Ground reference for digital circuitry.
17–18
16
17
12
13
BUF
LDAC
Buffer Control Pin. Controls whether the reference input to the DAC is buffered or unbuffered.
Active Low Control Input. Updates the DAC registers with the contents of the input registers, which
allows all DAC outputs to be simultaneously updated.
18
19
14
15
A0
A1
LSB Address Pin. Selects which DAC is to be written to.
Address Pin. Selects which DAC is to be written to.
20
23–32
33
16
19–28
29
A2
DB0–DB9
CS
MSB Address Pin. Selects which DAC is to be written to.
Ten Parallel Data Inputs. DB9 Is the MSB of these ten bits.
Active Low Chip Select Input. Used in conjunction with WR to write data to the parallel interface, or
with RD to read back data from a DAC.
34
35
36
37
38
30
31
32
33
34
RD
Active Low Read Input. Used in conjunction with CS to read data back from the internal DACs.
Active Low Write Input. Used in conjunction with CS to write data to the parallel interface.
WR
GAIN
CLR
PD
Gain Control Pin. Controls whether the output range from the DAC is 0 V to VREF or 0 V to 2 × VREF
Asynchronous Active Low Control Input. Clears all input registers and DAC registers to zeros.
Power-Down Pin. This active low control pin puts all DACs into power-down mode.
.
Rev. 0 | Page 8 of 24
AD5346/AD5347/AD5348
AD5348 PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
V
GH
EF
1
38
37
36
35
34
33
32
31
30
PD
REF
V
2
CLR
REF
V
V
CD
3
REF
40 39 38 37 36 35 34 33 32 31
GAIN
WR
4
V
V
V
V
V
A
B
C
D
1
2
30
29
28
27
26
25
24
23
22
21
DD
AB
A
OUT
OUT
OUT
OUT
RD
CS
DB
DB
DB
DB
DB
DB
DB
DB
5
REF
RD
CS
V
6
OUT
12-BIT
3
11
10
9
AD5348
TOP VIEW
(Not to Scale)
V
V
V
B
C
D
7
DB
11
OUT
OUT
OUT
4
12-BIT
8
DB
DB
10
9
5
AGND
AGND
AD5348
TOP VIEW
(Not to Scale)
9
6
8
10
11
12
13
14
15
16
17
18
19
29 DB
AGND
8
V
E
F
7
OUT
7
28
DB
V
E
7
OUT
V
8
OUT
6
27 DB
V
F
6
OUT
V
G
9
OUT
5
DB
26
25
5
V
G
OUT
V
H
10
OUT
4
DB
V
H
4
3
OUT
11 12 13 14 15 16 17 18 19 20
DGND
BUF
24 DB
23 DB
2
1
DB
DB
22
21
LDAC
A0
0
Figure 10. AD5348 Pin Configuration—LFCSP
20 A2
A1
Figure 9. AD5348 Pin Configuration—TSSOP
Table 7. AD5348 Pin Function Descriptions
Pin Number
TSSOP LFCSP Mnemonic Function
1
2
3
4
35
36
37
VREFGH
VREFEF
VREFCD
Reference Input for DACs G and H.
Reference Input for DACs E and F.
Reference Input for DACs C and D.
Power Supply Pin(s). This part can operate from 2.5 V to 5.5 V, and the supply should be decoupled with a
10 µF capacitor in parallel with a 0.1 µF capacitor to GND. Both VDD pins on the LFCSP package must be at
the same potential.
38, 39 VDD
5
6–9,
40
1–4,
VREFAB
VOUT
Reference Input for DACs A and B.
Output of DAC X. Buffered output with rail-to-rail operation.
X
11–14
7–10
10
15
16
17
5, 6
11
12
AGND
DGND
BUF
Analog Ground. Ground reference for analog circuitry.
Digital Ground. Ground reference for digital circuitry.
Buffer Control Pin. Controls whether the reference input to the DAC is buffered or unbuffered.
Active Low Control Input. Updates the DAC registers with the contents of the input registers, which allows
all DAC outputs to be simultaneously updated.
13
LDAC
18
19
20
21–32
33
14
15
16
A0
A1
A2
LSB Address Pin. Selects which DAC is to be written to.
Address Pin. Selects which DAC is to be written to.
MSB Address Pin. Selects which DAC is to be written to.
Twelve Parallel Data Inputs. DB11 is the MSB of these 12 bits.
Active Low Chip Select Input. Used in conjunction with WR to write data to the parallel interface, or with
RD to read back data from a DAC.
17–28 DB0–DB11
29
CS
34
35
36
37
38
30
31
32
33
34
RD
Active Low Read Input. Used in conjunction with CS to read data back from the internal DACs.
Active Low Write Input. Used in conjunction with CS to write data to the parallel interface.
WR
GAIN
CLR
PD
Gain Control Pin. Controls whether the output range from the DAC is 0 V to VREF or 0 V to 2 × VREF
Asynchronous Active Low Control Input. Clears all input registers and DAC registers to zeros.
Power-Down Pin. This active low control pin puts all DACs into power-down mode.
.
Rev. 0 | Page 9 of 24
AD5346/AD5347/AD5348
TERMINOLOGY
Relative Accuracy
GAIN ERROR
AND
OFFSET
ERROR
For the DAC, relative accuracy or integral nonlinearity (INL) is
a measure of the maximum deviation, in LSBs, from a straight
line passing through the actual endpoints of the DAC transfer
function. Typical INL versus code plots can be seen in Figure 14,
Figure 15, and Figure 16.
ACTUAL
OUTPUT
VOLTAGE
Differential Nonlinearity
Differential nonlinearity (DNL) is the difference between the
measured change and the ideal 1 LSB change between any two
adjacent codes. A specified differential nonlinearity of 1 LSB
maximum ensures monotonicity. This DAC is guaranteed
monotonic by design. Typical DNL versus code plots can be
seen in Figure 17, Figure 18, and Figure 19.
IDEAL
POSITIVE
OFFSET
Gain Error
DAC CODE
This is a measure of the span error of the DAC, including any
error in the gain of the buffer amplifier. It is the deviation in
slope of the actual DAC transfer characteristic from the ideal
and is expressed as a percentage of the full-scale range. This is
illustrated in Figure 11.
Figure 12. Positive Offset Error and Gain Error
GAIN ERROR
AND
OFFSET
ERROR
Offset Error
IDEAL
This is a measure of the offset error of the DAC and the output
amplifier. It is expressed as a percentage of the full-scale range.
OUTPUT
VOLTAGE
If the offset voltage is positive, the output voltage still positive at
zero input code. This is shown in Figure 12. Because the DACs
operate from a single supply, a negative offset cannot appear at
the output of the buffer amplifier. Instead, there is a code close
to zero at which the amplifier output saturates (amplifier
footroom). Below this code there is a dead band over which the
output voltage does not change. This is illustrated in Figure 13.
ACTUAL
NEGATIVE
OFFSET
DAC CODE
POSITIVE
GAIN ERROR
DEADBAND CODES
AMPLIFIER
FOOTROOM
(~1mV)
NEGATIVE
ACTUAL
GAIN ERROR
OUTPUT
VOLTAGE
NEGATIVE
OFFSET
IDEAL
Figure 13. Negative Offset Error and Gain Error
DAC CODE
Figure 11. Gain Error
Rev. 0 | Page 10 of 24
AD5346/AD5347/AD5348
Offset Error Drift
Digital Crosstalk
This is a measure of the change in offset error with changes in
temperature. It is expressed in (ppm of full-scale range)/°C.
This is the glitch impulse transferred to the output of one DAC
at midscale in response to a full-scale code change (all 0s to all
1s and vice versa) in the input register of another DAC. It is
expressed in nV-s.
Gain Error Drift
This is a measure of the change in gain error with changes in
temperature. It is expressed in (ppm of full-scale range)/°C.
Analog Crosstalk
This is the glitch impulse transferred to the output of one DAC
due to a change in the output of another DAC. It is measured by
loading one of the input registers with a full-scale code change
DC Power-Supply Rejection Ratio (PSRR)
This indicates how the output of the DAC is affected by changes
in the supply voltage. PSRR is the ratio of the change in VOUT to
a change in VDD for full-scale output of the DAC. It is measured
in dB. VREF is held at 2 V and VDD is varied 10%.
LDAC
(all 0s to all 1s and vice versa) while keeping
high. Then
low and monitor the output of the DAC whose
LDAC
pulse
digital code was not changed. The area of the glitch is expressed
in nV-s.
DC Crosstalk
This is the dc change in the output level of one DAC at midscale
in response to a full-scale code change (all 0s to all 1s and vice
versa) and output change of another DAC. It is expressed in µV.
DAC-to-DAC Crosstalk
This is the glitch impulse transferred to the output of one DAC
due to a digital code change and subsequent output change of
another DAC. This includes both digital and analog crosstalk. It
is measured by loading one of the DACs with a full-scale code
Reference Feedthrough
This is the ratio of the amplitude of the signal at the DAC
output to the reference input when the DAC output is not being
LDAC
change (all 0s to all 1s and vice versa) with the
pin set
low and monitoring the output of another DAC. The energy of
the glitch is expressed in nV-s.
LDAC
updated, i.e.,
is high. It is expressed in dB.
Channel-to-Channel Isolation
Multiplying Bandwidth
This is a ratio of the amplitude of the signal at the output of one
DAC to a sine wave on the reference inputs of the other DACs.
It is measured by grounding one VREF pin and applying a 10 kHz,
4 V p-p sine wave to the other VREF pins. It is expressed in dB.
The amplifiers within the DAC have a finite bandwidth. The
multiplying bandwidth is a measure of this. A sine wave on the
reference (with full-scale code loaded to the DAC) appears on
the output. The multiplying bandwidth is the frequency at
which the output amplitude falls to 3 dB below the input.
Major-Code Transition Glitch Energy
This is the energy of the impulse injected into the analog output
when the DAC changes state. It is normally specified as the area
of the glitch in nV-s and is measured when the digital code is
changed by 1 LSB at the major carry transition (011 . . . 11 to
100 . . . 00 or 100 . . . 00 to 011 . . . 11).
Total Harmonic Distortion (THD)
This is the difference between an ideal sine wave and its
attenuated version using the DAC. The sine wave is used as the
reference for the DAC, and the THD is a measure of the
harmonics present on the DAC output. It is measured in dB.
Digital Feedthrough
This is a measure of the impulse injected into the analog output
of the DAC from the digital input pins of the device, but it is
CS
measured when the DAC is not being written to,
held high.
It is specified in nV-s and is measured with a full-scale change
on the digital input pins, i.e., from all 0s to all 1s and vice versa.
Rev. 0 | Page 11 of 24
AD5346/AD5347/AD5348
TYPICAL PERFORMANCE CHARACTERISTICS
1.0
0.3
0.2
0.1
T
V
= 25°C
DD
T
= 25°C
A
A
= 5V
V
= 5V
DD
0.5
0
0
–0.1
–0.2
–0.3
–0.5
–1.0
0
50
100
150
200
250
1000
4000
0
0
0
50
100
150
200
250
CODE
CODE
Figure 14. AD5346 Typical INL Plot
Figure 17. AD5346 Typical DNL Plot
0.6
0.4
0.2
3
2
T
V
= 25°C
T
V
= 25°C
A
A
= 5V
= 5V
DD
DD
1
0
0
–0.2
–1
–2
–3
–0.4
–0.6
0
200
400
600
800
200
400
600
800
1000
CODE
CODE
Figure 15. AD5347 Typical INL Plot
Figure 18. AD5347 Typical DNL Plot
1.0
0.5
12
8
T
V
= 25°C
A
T
V
= 25°C
DD
A
= 5V
DD
= 5V
4
0
0
–4
–8
–12
–0.5
–1.0
1000
2000
3000
4000
0
1000
2000
3000
CODE
CODE
Figure 19. AD5348 Typical DNL Plot
Figure 16. AD5348 Typical INL Plot
Rev. 0 | Page 12 of 24
AD5346/AD5347/AD5348
0.2
0.1
0.5
0.4
0.3
0.2
0.1
0
V
T
= 5V
= 25°C
T
V
= 25°C
REF
DD
A
= 2V
A
MAX INL
0
GAIN ERROR
MAX DNL
–0.1
–0.2
–0.3
–0.4
–0.1
MIN DNL
MIN INL
–0.2
–0.3
–0.4
–0.5
OFFSET ERROR
–0.5
–0.6
0
1
2
3
4
5
0
1
2
3
4
5
6
V
(V)
V
(V)
REF
DD
Figure 20. AD5346 INL and DNL Error vs. VREF
Figure 23. Offset Error and Gain Error vs. VDD
0.5
0.4
0.3
5
V
V
= 5V
= 2V
DD
REF
MAX INL
5V SOURCE
3V SOURCE
4
3
0.2
0.1
0
MAX DNL
2
–0.1
–0.2
MIN DNL
MIN INL
–0.3
–0.4
–0.5
1
0
3V SINK
5V SINK
–40
–20
0
20
40
60
80
100
0
1
2
3
4
5
6
TEMPERATURE (°C)
SINK/SOURCE CURRENT (mA)
Figure 21. AD5346 INL and DNL Error vs. Temperature
Figure 24. VOUT Source and Sink Current Capability
1.0
0.5
1.0
0.9
0.8
0.7
0.6
0.5
V
V
= 5V
DD
= 2V
REF
V
= 5V
= 25°C
DD
T
A
0
–0.5
–1.0
OFFSET ERROR
0.4
0.3
0.2
GAIN ERROR
0.1
0
–40
–20
0
20
40
60
80
100
ZERO SCALE
HALF SCALE
DAC CODE
FULL SCALE
TEMPERATURE (°C)
Figure 22. AD5346 Offset Error and Gain Error vs. Temperature
Figure 25. Supply Current vs. DAC Code
Rev. 0 | Page 13 of 24
AD5346/AD5347/AD5348
1.4
T
V
V
= 25°C
= 5V
V
= 2V
A
REF
GAIN = 1 UNBUFFERED
DD
= 5V
1.2
REF
T
= –40°C
A
T
= +25°C
A
1.0
0.8
0.6
0.4
0.2
0
V
A
OUT
T
= +105°C
A
CH1
CH2
LDAC
CH1 1V, CH2 5V, TIME BASE = 1µs/DIV
2.5
3.0
3.5
4.0
4.5
5.0
5.5
SUPPLY VOLTAGE (V)
Figure 29. Half-Scale Settling (¼ to ¾ Scale Code)
Figure 26. Supply Current vs. Supply Voltage
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
T
V
V
= 25°C
= 5V
A
T
= 25°C
DD
A
= 2V
REF
CH1
V
DD
V
A
OUT
CH2
CH1 2V, CH2 200mV, TIME BASE = 200µs/DIV
2.0
2.5
3.0
3.5
4.0
(V)
4.5
5.0
5.5
V
DD
Figure 30. Power-On Reset to 0 V
Figure 27. Power-Down Current vs. Supply Voltage
2.5
T
= 25
°C
A
V
= 5V
DD
2.0
1.5
1.0
V
1
OUT
CH2
PD
V
= 3V
DD
0.5
0
CH1
CH1 2.00V, CH2 1.00V, TIME BASE = 20µs/DIV
0
1
2
3
4
5
VLOGIC (V)
Figure 31. Exiting Power-Down to Midscale
Figure 28. Supply Current vs. Logic Input Voltage
Rev. 0 | Page 14 of 24
AD5346/AD5347/AD5348
21
18
15
12
9
0.02
0.01
0
V
= 5V
= 25°C
DD
T
A
V
=
3V
V
= 5V
DD
DD
6
–0.01
–0.02
3
0
0
1
2
3
4
5
6
0.6
0.8
1.0
(mA)
1.2
1.4
V
(V)
REF
I
DD
Figure 35. Full-Scale Error vs. VREF
Figure 32. IDD Histogram with VDD = 3 V and VDD = 5 V
2.50
2.49
2.48
2.47
1.999
1.998
1.997
1.996
1µs/DIV
Figure 36. DAC-to-DAC Crosstalk
Figure 33. AD5348 Major Code Transition Glitch Energy
10
0
–10
–20
–30
–40
–50
–60
10
100
1k
10k
100k
1M
10M
FREQUENCY (Hz)
Figure 34. Multiplying Bandwidth (Small Signal Frequency Response)
Rev. 0 | Page 15 of 24
AD5346/AD5347/AD5348
FUNCTIONAL DESCRIPTION
V
REF
The AD5346/AD5347/AD5348 are octal resistor-string DACs
fabricated by a CMOS process with resolutions of 8, 10, and 12
bits, respectively. They are written to using a parallel interface.
They operate from single supplies of 2.5 V to 5.5 V, and the
output buffer amplifiers offer rail-to-rail output swing. The gain
of the buffer amplifiers can be set to 1 or 2 to give an output
voltage range of 0 V to VREF or 0 V to 2 × VREF. The AD5346/
AD5347/AD5348 have reference inputs that may be buffered to
draw virtually no current from the reference source. The devices
have a power-down feature that reduces current consumption
to only 100 nA @ 3 V.
R
R
R
TO OUTPUT
AMPLIFIER
R
R
DIGITAL-TO-ANALOG SECTION
Figure 38. Resistor String
The architecture of one DAC channel consists of a reference
buffer and a resistor-string DAC followed by an output buffer
amplifier. The voltage at the VREF pin provides the reference
voltage for the DAC. Figure 37 shows a block diagram of the
DAC architecture. Because the input coding to the DAC is
straight binary, the ideal output voltage is given by
DAC REFERENCE INPUT
The DACs operate with an external reference. The AD5346/
AD5347/AD5348 have a reference input for each pair of DACs.
The reference inputs may be configured as buffered or
unbuffered. This option is controlled by the BUF pin.
D
V
OUT =VREF
×
×Gain
In buffered mode (BUF = 1), the current drawn from an
external reference voltage is virtually zero because the imped-
ance is at least 10 MΩ. The reference input range is 1 V to VDD.
2N
where:
In unbuffered mode (BUF = 0), the user can have a reference
voltage as low as 0.25 V and as high as VDD because there is no
restriction due to headroom and footroom of the reference
amplifier. The impedance is still large at typically 90 kΩ for 0 V
to VREF mode and 45 kΩ for 0 V to 2 × VREF mode.
D is the decimal equivalent of the binary code, which is loaded
to the DAC register:
0–255 for AD5346 (8 bits)
0–1023 for AD5347 (10 bits)
0–4095 for AD5348 (12 bits)
N is the DAC resolution.
Gain is the output amplifier gain (1 or 2).
If using an external buffered reference (such as REF192), there
is no need to use the on-chip buffer.
V
AB
REF
OUTPUT AMPLIFIER
The output buffer amplifier is capable of generating output
voltages to within 1 mV of either rail. Its actual range depends
on VREF, GAIN, the load on VOUT, and offset error.
REFERENCE
BUFFER
BUF
(GAIN = +1 OR +2)
If a gain of +1 is selected (GAIN = 0), the output range is
DAC
REGISTER
RESISTOR
STRING
INPUT
REGISTER
V
A
OUT
0.001 V to VREF
.
OUTPUT
BUFFER AMPLIFIER
If a gain of +2 is selected (GAIN = +1), the output range is
0.001 V to 2 × VREF. However, because of clamping, the
maximum output is limited to VDD – 0.001 V.
Figure 37. Single DAC Channel Architecture
RESISTOR STRING
The output amplifier is capable of driving a load of 2 kΩ to
GND or VDD, in parallel with 500 pF to GND or VDD. The source
and sink capabilities of the output amplifier can be seen in
Figure 24.
The resistor string section is shown in Figure 38. It is simply a
string of resistors, each of value R. The digital code loaded to
the DAC register determines at what node on the string the
voltage is tapped off to be fed into the output amplifier. The
voltage is tapped off by closing one of the switches connecting
The slew rate is 0.7 V/µs with a half-scale settling time to 0.5 LSB
(at 8 bits) of 6 s with the output unloaded. See Figure 29.
the string to the amplifier. Because it is a string of resistors, it is
guaranteed monotonic.
Rev. 0 | Page 16 of 24
AD5346/AD5347/AD5348
where IDYNAMIC
=
cvf and
PARALLEL INTERFACE
c = capacitance or the data bus
v = VDD
f = readback frequency
The AD5346/AD5347/AD5348 load their data as a single 8-,
10-, or 12-bit word.
Double-Buffered Interface
LDAC
Load DAC Input (
)
The AD5346/AD5347/AD5348 DACs all have double-buffered
interfaces consisting of an input register and a DAC register.
DAC data, BUF, and GAIN inputs are written to the input regis-
LDAC
transfers data from the input register to the DAC register,
LDAC
and therefore updates the outputs. The
function enables
double-buffering of the DAC data, GAIN data, and BUF. There
LDAC
CS
WR
ter under control of the Chip Select ( ) and Write (
) pins.
are two
modes:
LDAC
Access to the DAC register is controlled by the
LDAC
function.
•
Synchronous Mode. In this mode, the DAC register is
When
register may change state without affecting the contents of the
LDAC
is high, the DAC register is latched and the input
updated after new data is read in on the rising edge of the
WR
LDAC
input.
shown in Figure 3.
can be tied permanently low or pulsed as
DAC register. However, when
is brought low, the DAC
register becomes transparent and the contents of the input
register are transferred to it. The gain and buffer control signals
are also double-buffered and are updated only when
taken low.
•
Asynchronous Mode. In this mode, the outputs are not
updated at the same time that the input register is written
to. When
the contents of the input register.
LDAC
is
LDAC
goes low, the DAC register is updated with
This is useful if the user requires simultaneous updating of all
DACs and peripherals. The user can write to all input registers
POWER-ON RESET
The AD5346/AD5347/AD5348 have a power-on reset function,
so that they power up in a defined state. The power-on state is
LDAC
individually and then, by pulsing the
outputs update simultaneously.
input low, all
•
•
•
•
Normal operation
These parts contain an extra feature whereby the DAC register
is not updated unless its input register has been updated since
Reference input buffered
0 V to VREF output range
Output voltage set to 0 V
LDAC
the last time that
was brought low. Normally, when
LDAC
is brought low, the DAC registers are filled with the
Both input and DAC registers are filled with zeros and remain
so until a valid write sequence is made to the device. This is
particularly useful in applications where it is important to know
the state of the DAC outputs while the device is powering up.
contents of the input registers. In the case of the AD5346/
AD5347/AD5348, the part updates the DAC register only if the
input register has been changed since the last time the DAC
register was updated. This removes unnecessary crosstalk.
CLR
Clear Input (
)
POWER-DOWN MODE
CLR
is an active low, asynchronous clear that resets the input
The AD5346/AD5347/AD5348 have low power consumption,
dissipating typically 2.4 mW with a 3 V supply and 5 mW with
a 5 V supply. Power consumption can be further reduced when
the DACs are not in use by putting them into power-down
and DAC registers.
CS
Chip Select Input (
)
CS
is an active low input that selects the device.
PD
mode, which is selected by taking the
pin low.
WR
Write Input (
)
PD
When the
pin is high, the DACs work normally with a typi-
WR
is an active low input that controls writing of data to the
device. Data is latched into the input register on the rising edge
WR
cal power consumption of 1 mA at 5 V (0.8 mA at 3 V). In
power-down mode, however, the supply current falls to 400 nA
at 5 V (120 nA at 3 V) when the DACs are powered down. Not
only does the supply current drop, but the output stage is also
internally switched from the output of the amplifier, making it
open-circuit. This has the advantage that the outputs are three-
state while the part is in power-down mode, and provides a
defined input condition for whatever is connected to the outputs
of the DAC amplifiers. The output stage is illustrated in Figure 39.
of
.
RD
Read Input (
)
RD
is an active low input that controls when data is read back
RD
from the internal DAC registers. On the falling edge of
is shifted onto the data bus. Under the conditions of a high
capacitive load and high supplies, the user must ensure that the
dynamic current remains at an acceptable level, therefore
ensuring that the die temperature is within specification. The
die temperature can be calculated as
, data
RESISTOR
STRING DAC
AMPLIFIER
V
OUT
POWER-DOWN
CIRCUITRY
TDIE = TAMBIENT + VDD (IDD + IDYNAMIC)θJA
Figure 39. Output Stage During Power-Down
Rev. 0 | Page 17 of 24
AD5346/AD5347/AD5348
The bias generator, the output amplifier, the resistor string, and
all other associated linear circuitry are all shut down when the
power-down mode is activated. However, the contents of the
registers are unaffected when in power-down. The time to exit
power-down is typically 2.5 s for VDD = 5 V and 5 µs when VDD
The AD5347 and AD5348 data bus must be at least 10 and 12
bits wide, respectively, and are best suited to a 16-bit data bus
system.
Examples of data formats for putting GAIN and BUF on a
16-bit data bus are shown in Figure 40. Note that any unused
bits above the actual DAC data may be used for GAIN and BUF.
=
PD
3 V. This is the time from a rising edge on the
pin to when
the output voltage deviates from its power-down voltage. See
Figure 31.
AD5347
X
X
X
X
BUF GAIN DB9 DB8 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
SUGGESTED DATA BUS FORMATS
AD5348
In many applications, the GAIN and BUF pins are hardwired.
However, if more flexibility is required, they can be included in
a data bus. This enables the user to software program GAIN,
giving the option of doubling the resolution in the lower half of
the DAC range. In a bused system, GAIN and BUF may be
treated as data inputs because they are written to the device
X
X
BUF GAIN DB11 DB10 DB9 DB8 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
X = UNUSED BIT
Figure 40. AD5347/AD5348 Data Format for Word Load with
GAIN and BUF Data on 16-Bit Bus
LDAC
during a write operation and take effect when
is taken
low. This means that the reference buffers and the output
amplifier gain of multiple DAC devices can be controlled using
common GAIN and BUF lines. Note that GAIN and BUF are
RD
not read back during an
operation.
Table 8. AD5346/AD5347/AD5348 Truth Table
CLR
LDAC
CS
WR
RD
A2
X
X
X
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
X
X
A1
X
X
X
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
X
X
A0
X
X
X
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
X
X
Function
1
1
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
X
1
1
X
1
1
1
1
1
1
1
1
X
X
X
X
X
X
X
X
0
X
1
X
X
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
X
0
X
1
X
X
1
X
1
No Data Transfer
No Data Transfer
Clear All Registers
Load DAC A Input Register
Load DAC B Input Register
Load DAC C Input Register
Load DAC D Input Register
Load DAC E Input Register
Load DAC F Input Register
Load DAC G Input Register
Load DAC H Input Register
Read Back DAC Register A
Read Back DAC Register B
Read Back DAC Register C
Read Back DAC Register D
Read Back DAC Register E
Read Back DAC Register F
Read Back DAC Register G
Read Back DAC Register H
Update DAC Registers
Invalid Operation
0→1
0→1
0→1
0→1
0→1
0→1
0→1
0→1
1
1
1
1
1
1
1
1
1→0
1→0
1→0
1→0
1→0
1→0
1→0
1→0
1
1
1
1
1
1
1
1
X
0
0
X = Don’t Care
Rev. 0 | Page 18 of 24
AD5346/AD5347/AD5348
APPLICATIONS INFORMATION
TYPICAL APPLICATION CIRCUITS
BIPOLAR OPERATION USING THE
AD5346/AD5347/AD5348
The AD5346/AD5347/AD5348 can be used with a wide range
of reference voltages, especially if the reference inputs are
configured as unbuffered, in which case the devices offer full,
one-quadrant multiplying capability over a reference range of
0.25 V to VDD. More typically, these devices may be used with a
fixed, precision reference voltage. Figure 41 shows a typical
setup for the devices when using an external reference
connected to the reference inputs. Suitable references for 5 V
operation are the AD780, ADR381, and REF192 (2.5 V refer-
ences). For 2.5 V operation, suitable external references are the
AD589 and the AD1580 (1.2 V band gap references).
The AD5346/AD5347/AD5348 have been designed for single-
supply operation, but a bipolar output range is also possible by
using the circuit shown in Figure 43. This circuit has an output
voltage range of 5 V. Rail-to-rail operation at the amplifier
output is achievable using an AD820, an AD8519, or an OP196
as the output amplifier.
5V
R4
20kΩ
0.1µF
10µF
+5V
R3
10kΩ
V
= 2.5V to 5.5V
DD
V
±5V
IN
V
DD
EXT
REF
AD820/AD8519/
OP196
V
*
V
REF
OUT
0.1µF
10µF
–5V
0.1µF
AD5346/AD5347/
AD5348
GND
R1
10kΩ
V
IN
V
*
OUT
V
DD
EXT
REF
V
V
*
R2
20kΩ
OUT
REF
V
*
OUT
GND
AD5346/AD5347/
AD5348
*ONLY ONE CHANNEL OF V
REF
AND V
SHOWN
OUT
AD780/ADR381/REF192
WITH V = 5V
DD
OR AD589/AD1580 WITH
GND
Figure 43. Bipolar Operation with the AD5346/ AD5347/AD5348
V
= 2.5V
DD
*ONLY ONE CHANNEL OF V
AND V
SHOWN
REF
OUT
The output voltage for any input code can be calculated as
follows:
Figure 41. AD5346/AD5347/AD5348 Using an External Reference
VOUT = [(1 + R4/R3) × (R2/(R1 + R2) × (2 × VREF × D/2N)] –
R4 × VREF/R3
DRIVING VDD FROM THE REFERENCE VOLTAGE
If an output range of 0 V to VDD is required, the simplest
solution is to connect the reference inputs to VDD. Because this
supply may not be very accurate and may be noisy, the devices
can be powered from the reference voltage, for example, by
using a 5 V reference such as the ADM663 or ADM666, as
shown in Figure 42.
where:
D is the decimal equivalent of the code loaded to the DAC.
N is the DAC resolution.
VREF is the reference voltage input.
with:
6V TO 16V
VREF = 5 V
10µF
0.1µF
R1 = R3 = 10 kΩ
R2 = R4 = 20 kΩ
VDD = 5 V
V
IN
ADM663/ADM666
GAIN = 2
V
V
SENSE
EXT
DD
V
*
REF
V
OUT
*
OUT(2)
REF
VOUT = (10 × D/2N) – 5
0.1µF
VSET GND SHDN
AD5346/AD5347/
AD5348
GND
*ONLY ONE CHANNEL OF V
AND V
SHOWN
OUT
REF
Figure 42. Using an ADM663/ADM666 as Power and
Reference to the AD5346/AD5347/AD5348
Rev. 0 | Page 19 of 24
AD5346/AD5347/AD5348
5V
DECODING MULTIPLE AD5346/AD5347/AD5348s
0.1µF
10µF
1kΩ
1kΩ
V
IN
FAIL
PASS
CS
The
decode a number of DACs. In this application, all DACs in the
WR CS
to
pin on these devices can be used in applications to
V
DD
V
V
AB
REF
REF
V
A
OUT
system receive the same data and
one of the DACs will be active at any one time, so data will only
CS
pulses, but only the
PASS/
FAIL
1/2
CMP04
AD5346/AD5347/
AD5348
be written to the DAC whose
is low.
V
B
OUT
1/6 74HC05
GND
The 74HC139 is used as a 2-line to 4-line decoder to address
any of the DACs in the system. To prevent timing errors from
occurring, the enable input should be brought to its inactive
state while the coded address inputs are changing state.
Figure 44 shows a diagram of a typical setup for decoding
multiple devices in a system. Once data has been written
sequentially to all DACs in a system, all the DACs can be
Figure 45. Programmable Window Detector
PROGRAMMABLE CURRENT SOURCE
Figure 46 shows the AD5346/AD5347/AD5348 used as the
control element of a programmable current source. In this
example, the full-scale current is set to 1 mA. The output
voltage from the DAC is applied across the current setting
resistor of 4.7 kΩ in series with the 470 Ω adjustment
potentiometer, which gives an adjustment of about 5%.
Suitable transistors to place in the feedback loop of the ampli-
fier include the BC107 and the 2N3904, which enable the
current source to operate from a minimum VSOURCE of 6 V. The
operating range is determined by the operating characteristics
of the transistor. Suitable amplifiers include the AD820 and the
OP295, both having rail-to-rail operation on their outputs. The
current for any digital input code and resistor value can be
calculated as follows:
LDAC
updated simultaneously using a common
line. A com-
CLR
mon
line can also be used to reset all DAC outputs to 0 V.
AD5346/AD5347
A0
/AD5348
A0
A1
A2
A1
A2
WR
LDAC
CLR
WR
LDAC
CLR
CS
DATA
INPUTS
AD5346/AD5347
/AD5348
A0
A1
A2
WR
DATA
LDAC
CLR
CS
INPUTS
V
DD
D
I = G ×VREF (2N × R)
mA
V
CC
1G
1A
1B
AD5346/AD5347
1Y0
1Y1
1Y2
ENABLE
CODED
/AD5348
A0
A1
A2
where:
74HC139
DGND
ADDRESS
WR
LDAC
CLR
CS
DATA
INPUTS
1Y3
G is the gain of the buffer amplifier (1 or 2).
D is the digital input code.
N is the DAC resolution (8, 10, or 12 bits).
R is the sum of the resistor plus adjustment potentiometer in kΩ.
AD5346/AD5347
/AD5348
A0
A1
A2
WR
LDAC
CLR
CS
DATA
INPUTS
V
= 5V
DD
0.1µF
0.1µF
10µF
Figure 44. Decoding Multiple DAC Devices
V
SOURCE
AD5346/AD5347/AD5348 AS DIGITALLY
PROGRAMMABLE WINDOW DETECTORS
V
IN
5V
LOAD
V
DD
EXT
REF
V
V
*
V
*
OUT
OUT
REF
A digitally programmable upper/lower limit detector using two
of the DACs in the AD5346/AD5347/AD5348 is shown in
Figure 45. Any pair of DACs in the device may be used, but for
simplicity the description refers to DACs A and B.
AD5346/AD5347/
AD5348
GND
4.7kΩ
470Ω
The upper and lower limits for the test are loaded to DACs A
and B which, in turn, set the limits on the CMP04. If a signal at
the VIN input is not within the programmed window, an LED
indicates the fail condition.
GND
*ONLY ONE CHANNEL OF V
AND V
SHOWN
REF
OUT
Figure 46. Programmable Current Source
Rev. 0 | Page 20 of 24
AD5346/AD5347/AD5348
COARSE AND FINE ADJUSTMENT USING
THE AD5346/AD5347/AD5348
POWER SUPPLY BYPASSING AND GROUNDING
In any circuit where accuracy is important, careful consideration
of the power supply and ground return layout helps to ensure
the rated performance.
Two of the DACs in the AD5346/AD5347/AD5348 can be
paired together to form a coarse and fine adjustment function,
as shown in Figure 47. As with the window comparator
previously described, the description refers to DACs A and B.
The printed circuit board on which the AD5346/AD5347/
AD5348 is mounted should be designed so that the analog and
digital sections are separated and are confined to certain areas
of the board. This facilitates the use of ground planes that can
be separated easily. A minimum etch technique is generally best
for ground planes because it gives the best shielding. Digital and
analog ground planes should be joined in one place only. If the
AD5346/AD5347/AD5348 is the only device requiring an
AGND-to-DGND connection, then the ground planes should
be connected at the AGND and DGND pins of the AD5346/
AD5347/AD5348. If the AD5346/AD5347/AD5348 is in a
system where multiple devices require AGND-to-DGND
connections, the connection should be made at one point only, a
star ground point that should be established as close as possible
to the AD5346/AD5347/AD5348.
DAC A provides the coarse adjustment, while DAC B provides
the fine adjustment. Varying the ratio of R1 and R2 changes the
relative effect of the coarse and fine adjustments. With the
resistor values shown, the output amplifier has unity gain for
the DAC A output, so the output range is 0 V to (VREF – 1 LSB).
For DAC B, the amplifier has a gain of 7.6 × 10–3, giving DAC B
a range equal to 2 LSBs of DAC A.
The circuit is shown with a 2.5 V reference, but reference
voltages up to VDD may be used. The op amps indicated allow a
rail-to-rail output swing.
V
= 5V
DD
R4
R3
390Ω
51.2kΩ
0.1µF
10µF
5V
The AD5346/AD5347/AD5348 should have ample supply
bypassing of 10 µF in parallel with 0.1 µF on the supply located
as close to the package as possible, ideally right up against the
device. The 10 µF capacitors are the tantalum bead type. The
0.1 µF capacitor should have low effective series resistance
(ESR) and effective series inductance (ESI), such as the
common ceramic types that provide a low impedance path to
ground at high frequencies to handle transient currents due to
internal logic switching.
V
DD
V
V
OUT
IN
V
A
OUT
EXT
REF
R1
390Ω
V
V
AB
OUT
REF
0.1µF
AD5346/AD5347/
AD5348
GND
R2
51.2kΩ
V
B
OUT
AD780/ADR381/REF192
WITH V = 5V
DD
GND
Figure 47. Coarse and Fine Adjustment
The power supply lines of the device should use the largest trace
possible to provide low impedance paths and to reduce the
effects of glitches on the power supply line. Fast switching
signals such as clocks should be shielded with digital ground to
avoid radiating noise to other parts of the board, and should
never be run near the reference inputs. Avoid crossover of
digital and analog signals. Traces on opposite sides of the board
should run at right angles to each other to reduce the effects of
feedthrough through the board. A microstrip technique is by far
the best, but not always possible with a double-sided board. In
this technique, the component side of the board is dedicated to
ground plane, while signal traces are placed on the solder side.
Rev. 0 | Page 21 of 24
AD5346/AD5347/AD5348
Table 9. Overview of AD53xx Parallel Devices
Additional Pin Functions
BUF GAIN HBEN CLR
Part No.
SINGLES
AD5330
AD5331
AD5340
AD5341
DUALS
AD5332
AD5333
AD5342
AD5343
QUADS
AD5334
AD5335
AD5336
AD5344
OCTALS
AD5346
AD5347
AD4348
Resolution
DNL
VREF Pins
Settling Time
Package
Pins
8
0.25
1
1
1
1
6 µs
7 µs
8 µs
8 µs
TSSOP
TSSOP
TSSOP
TSSOP
20
20
24
20
9
9
9
9
9
9
9
9
9
10
12
12
0.5
1.0
1.0
9
9
9
8
0.25
0.5
1.0
2
2
2
1
6 µs
7 µs
8 µs
8 µs
TSSOP
TSSOP
TSSOP
TSSOP
20
24
28
20
9
9
9
9
10
12
12
9
9
9
9
1.0
9
9
8
0.25
0.5
0.5
2
2
4
4
6 µs
7 µs
7 µs
8 µs
TSSOP
TSSOP
TSSOP
TSSOP
24
24
28
28
9
9
9
9
9
10
10
12
1.0
8
10
12
0.25
0.5
1.0
4
4
4
6 µs
7 µs
8 µs
TSSOP, LFCSP
TSSOP, LFCSP
TSSOP, LFCSP
38, 40
38, 40
38, 40
9
9
9
9
9
9
9
9
9
Table 10. Overview of AD53xx Serial Devices
Part No.
SINGLES
AD5300
AD5310
AD5320
AD5301
AD5311
AD5321
DUALS
AD5302
AD5312
AD5322
AD5303
AD5313
AD5323
QUADS
AD5304
AD5314
AD5324
AD5305
AD5315
AD5325
AD5306
AD5316
AD5326
AD5307
AD5317
AD5327
OCTALS
AD5308
AD5318
AD5328
Resolution
DNL
VREF Pins
Settling Time
Interface
Package
Pins
8
0.25
0 (VREF = VDD)
0 (VREF = VDD)
0 (VREF = VDD)
0 (VREF = VDD)
0 (VREF = VDD)
0 (VREF = VDD)
4 µs
6 µs
8 µs
6 µs
7 µs
8 µs
SPI®
SPI
SPI
2-Wire
2-Wire
2-Wire
SOT-23, MSOP
SOT-23, MSOP
SOT-23, MSOP
SOT-23, MSOP
SOT-23, MSOP
SOT-23, MSOP
6, 8
6, 8
6, 8
6, 8
6, 8
6, 8
10
12
8
10
12
0.5
1.0
0.25
0.5
1.0
8
0.25
0.5
1.0
0.25
0.5
1.0
2
2
2
2
2
2
6 µs
7 µs
8 µs
6 µs
7 µs
8 µs
SPI
SPI
SPI
SPI
SPI
SPI
MSOP
MSOP
MSOP
TSSOP
TSSOP
TSSOP
8
8
8
16
16
16
10
12
8
10
12
8
0.25
0.5
1.0
0.25
0.5
1.0
0.25
0.5
1.0
0.25
0.5
1.0
1
1
1
1
1
1
4
4
4
2
2
2
6 µs
7 µs
8 µs
6 µs
7 µs
8 µs
6 µs
7 µs
8 µs
6 µs
7 µs
8 µs
SPI
SPI
SPI
2-Wire
2-Wire
2-Wire
2-Wire
2-Wire
2-Wire
SPI
MSOP
MSOP
MSOP
MSOP
MSOP
MSOP
TSSOP
TSSOP
TSSOP
TSSOP
TSSOP
TSSOP
10
10
10
10
10
10
16
16
16
16
16
16
10
12
8
10
12
8
10
12
8
10
12
SPI
SPI
8
10
12
0.25
0.5
1.0
2
2
2
6 µs
7 µs
8 µs
SPI
SPI
SPI
TSSOP
TSSOP
TSSOP
16
16
16
Rev. 0 | Page 22 of 24
AD5346/AD5347/AD5348
OUTLINE DIMENSIONS
9.80
9.70
9.60
38
20
19
4.50
4.40
4.30
6.40 BSC
1
PIN 1
1.20
MAX
0.15
0.05
8°
0°
0.50
BSC
0.27
0.17
0.70
0.60
0.45
SEATING
PLANE
0.20
0.09
COPLANARITY
0.10
COMPLIANT TO JEDEC STANDARDS MO-153BD-1
Figure 48. 38-Lead Thin Shrink Small Outline Package [TSSOP]
(RU-38)
Dimensions shown in millimeters
6.00
BSC SQ
0.60 MAX
0.60 MAX
PIN 1
INDICATOR
31
30
40
1
PIN 1
INDICATOR
0.50
BSC
4.25
TOP
VIEW
5.75
BSC SQ
BOTTOM
VIEW
4.10 SQ
3.95
0.50
0.40
0.30
21
20
10
11
0.25 MIN
4.50
REF
12° MAX
0.80 MAX
0.65 TYP
0.05 MAX
0.02 NOM
1.00
0.85
0.80
0.30
0.23
0.18
COPLANARITY
0.08
0.20 REF
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-220-VJJD-2
Figure 49. 40-Lead Lead Frame Chip Scale Package [LFCSP]
(CP-40)
Dimensions shown in millimeters
Rev. 0 | Page 23 of 24
AD5346/AD5347/AD5348
ORDERING GUIDES
Table 11. AD5346 Ordering Guide
Model
Temperature Range
Package Description
Package Option
RU-38
RU-38
RU-38
CP-40
AD5346BRU
–40°C to +105°C
–40°C to +105°C
–40°C to +105°C
–40°C to +105°C
–40°C to +105°C
–40°C to +105°C
TSSOP (Thin Shrink Small Outline Package)
TSSOP (Thin Shrink Small Outline Package)
TSSOP (Thin Shrink Small Outline Package)
LFCSP (Lead Frame Chip Scale Package)
LFCSP (Lead Frame Chip Scale Package)
LFCSP (Lead Frame Chip Scale Package)
AD5346BRU-REEL
AD5346BRU-REEL7
AD5346BCP
AD5346BCP-REEL
AD5346BCP-REEL7
CP-40
CP-40
Table 12. AD5347 Ordering Guide
Model
Temperature Range
Package Description
Package Option
RU-38
RU-38
RU-38
CP-40
AD5347BRU
–40°C to +105°C
–40°C to +105°C
–40°C to +105°C
–40°C to +105°C
–40°C to +105°C
–40°C to +105°C
TSSOP (Thin Shrink Small Outline Package)
TSSOP (Thin Shrink Small Outline Package)
TSSOP (Thin Shrink Small Outline Package)
LFCSP (Lead Frame Chip Scale Package)
LFCSP (Lead Frame Chip Scale Package)
LFCSP (Lead Frame Chip Scale Package)
AD5347BRU-REEL
AD5347BRU-REEL7
AD5347BCP
AD5347BCP-REEL
AD5347BCP-REEL7
CP-40
CP-40
Table 13. AD5348 Ordering Guide
Model
Temperature Range
Package Description
Package Option
RU-38
RU-38
RU-38
CP-40
AD5348BRU
–40°C to +105°C
–40°C to +105°C
–40°C to +105°C
–40°C to +105°C
–40°C to +105°C
–40°C to +105°C
TSSOP (Thin Shrink Small Outline Package)
TSSOP (Thin Shrink Small Outline Package)
TSSOP (Thin Shrink Small Outline Package)
LFCSP (Lead Frame Chip Scale Package)
LFCSP (Lead Frame Chip Scale Package)
LFCSP (Lead Frame Chip Scale Package)
AD5348BRU-REEL
AD5348BRU-REEL7
AD5348BCP
AD5348BCP-REEL
AD5348BCP-REEL7
CP-40
CP-40
©
2003 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
C03331–0–11/03(0)
Rev. 0 | Page 24 of 24
相关型号:
AD5347BRUZ
PARALLEL, WORD INPUT LOADING, 7 us SETTLING TIME, 10-BIT DAC, PDSO38, MO-153BD-1, TSSOP-38
ROCHESTER
AD5348BCPZ
PARALLEL, WORD INPUT LOADING, 8 us SETTLING TIME, 12-BIT DAC, QCC40, 6 X 6 MM, MO-220-VJJD-2, LFCSP-40
ROCHESTER
©2020 ICPDF网 联系我们和版权申明