AD7386_技术文档

Differential Input, Quad, Internal Reference

Simultaneous Sampling, 16-Bit SAR ADC

AD7389-4

Data Sheet

FEATURES

FUNCTIONAL BLOCK DIAGRAM

V

REFOUT

REFCAP REFGND

V

LOGIC

CC

16-bit ADC family

Quad simultaneous sampling

Fully differential analog inputs

Wide common-mode range

High throughput rate: 2 MSPS

Buffered 2.5 V internal voltage reference (10 ppm/°C)

On-chip oversampling function

INL (maximum): 2 LSBs

SNR (typical)

90.5 dB at V_REF= 2.5 V

97.9 dB at RES = 1, OSR = 8× rolling average oversampling

2-bit resolution boost

REGCAP

LDO

REF

A

A+

IN

OSC

ADC A

OVERSAMPLING

A

A–

IN

SDOA

SDOB

SDOC

A

B+

IN

OVERSAMPLING

ADC B

ADC C

A

B–

IN

INTERFACE

AND

CONTROL

LOGIC

SDOD/

ALERT

A

C+

IN

A

C–

SCLK

SDI

IN

CS

A

D+

IN

ADC D

GND

ALERT

Out of range indicator (

)

AD7389-4

A

D–

IN

High-speed serial interface

−40°C to +125°C operation

4 mm × 4 mm, 24-lead LFCSP

GND

Figure 1.

APPLICATIONS

Motor control position feedback

Motor control current sense

Data acquisition systems

Erbium doped fiber amplifier (EDFA) applications

In phase and quadrature demodulation

GENERAL DESCRIPTION

The AD7389-4 a 16-bit, quad, simultaneous sampling, high

speed, successive approximation register (SAR), analog-to-digital

converter (ADC) that operates from a 3.0 V to 3.6 V power

supply and features throughput rates up to 2 MSPS. The analog

input type is differential, accepts a wide common-mode input

voltage, and the analog inputs are sampled and converted on

Table 1. Related Devices

No. of

Channels Input Type

16 Bits

14 Bits

12 Bits

4

2

Differential

AD7380-4 AD7381-4

AD7389-4

Differential

AD7380

AD4680

AD4681

AD7381

CS

the falling edge of

.

The AD7389-4 has on-chip oversampling blocks to improve

dynamic range and reduce noise at lower bandwidths. The

oversampling can boost up to two bits of added resolution. A

buffered internal 2.5 V reference (10 ppm/°C) is included.

Single-ended AD7386

AD7387

AD7388

PRODUCT HIGHLIGHTS

1. Quad simultaneous sampling and conversion.

2. Pin-compatible product family.

3. High throughput rate, 2 MSPS at 16-bit.

4. Space-saving, 4 mm × 4 mm LFCSP.

5. Integrated oversampling block to increase dynamic range,

reduce noise and reduce SCLK speed requirements.

6. Differential analog inputs with wide common-mode range.

7. Small sampling capacitor reduces amplifier drive burden.

The conversion process and data acquisition use standard

control inputs allowing for easy interfacing to microprocessors

or digital signal processors (DSPs). The conversion result can

clock out simultaneously via 4-wire mode for faster throughput or

via 1-wire serial mode when slower throughput is allowed. The

device is compatible with 1.8 V, 2.5 V, and 3.3 V interfaces,

using the separate logic supply.

The AD7389-4 is available in a 24-lead lead frame chip scale

package (LFCSP) with operation specified from −40°C to +125°C.

Rev. 0

Document Feedback

Information furnished by Analog Devices is believed to be accurate and reliable. However, no

responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other

rights of third parties that may result from its use. Specifications subject to change without notice.

No license is granted by implication or otherwise under any patent or patent rights of Analog

Devices. Trademarks and registeredtrademarks are the property of their respective owners.

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.

Tel: 781.329.4700

Technical Support

www.analog.com

AD7389-4

Data Sheet

TABLE OF CONTENTS

Features.............................................................................................. 1

Oversampling ............................................................................. 17

Resolution Boost ........................................................................ 19

Alert.............................................................................................. 19

Power Modes .............................................................................. 19

Internal Reference...................................................................... 20

Software Reset............................................................................. 20

Diagnostic Self Test.................................................................... 20

Interface........................................................................................... 21

Reading Conversion Results..................................................... 21

Low Latency Readback.............................................................. 22

Reading from Device Registers ................................................ 23

Writing to Device Registers...................................................... 23

CRC.............................................................................................. 23

Registers........................................................................................... 26

Addressing Registers.................................................................. 26

Configuration 1 Register........................................................... 27

Configuration 2 Register........................................................... 28

Alert Indication Register........................................................... 28

Alert Low Threshold Register .................................................. 29

Alert High Threshold Register ................................................. 30

Outline Dimensions....................................................................... 31

Ordering Guide .......................................................................... 31

Applications ...................................................................................... 1

Functional Block Diagram .............................................................. 1

General Description......................................................................... 1

Product Highlights........................................................................... 1

Revision History ............................................................................... 2

Specifications .................................................................................... 3

Timing Specifications .................................................................. 5

Absolute Maximum Ratings ........................................................... 8

Thermal Resistance...................................................................... 8

Electrostatic Discharge (ESD) Ratings...................................... 8

ESD Caution.................................................................................. 8

Pin Configuration and Function Descriptions ............................ 9

Typical Performance Characteristics........................................... 10

Terminology.................................................................................... 13

Theory of Operation ...................................................................... 14

Circuit Information ................................................................... 14

Converter Operation.................................................................. 14

Analog Input Structure.............................................................. 14

ADC Transfer Function ............................................................ 15

Applications Information.............................................................. 16

Power Supply .............................................................................. 16

Modes of Operation ....................................................................... 17

REVISION HISTORY

1/2022—Revision 0: Initial Version

Rev. 0 | Page 2 of 31

Data Sheet

AD7389-4

SPECIFICATIONS

V_CC= 3.0 V to3.6 V, V_LOGIC= 1.65 V to 3.6 V, internal reference voltage (V_REF) = 2.5 V, f_SAMPLE= 2 MSPS, T_A= −40°C to +125°C, no

oversampling enabled, unless otherwise noted.

Table 2.

Parameter

Test Conditions/Comments

Min

Typ

Max

Unit

RESOLUTION

16

Bits

THROUGHPUT

Conversion Rate (f_SAMPLE

ANALOG INPUT

Voltage Range

Absolute Input Voltage

Common-Mode Input Range

)

2

MSPS

A_INx+ − A_INx−

A_INx+, A_INx−

−V_REF

−0.1

0.2

+V_REF

V_REF+ 0.1

V_REF× 0.5 V_REF− 0.2

−76

V

dB

Analog Input Common-Mode Rejection Ratio f_IN= 500 kHz

(CMRR)

µA

pF

DC Leakage Current

Input Capacitance

0.1

18

5

1

Track mode

Hold mode

DC ACCURACY

No Missing Codes

16

Bits

Differential Nonlinearity (DNL) Error

Integral Nonlinearity (INL) Error

Gain Error

Gain Error Temperature Drift

Gain Error Match

Zero Error

Zero Error Temperature Drift

Zero Error Match

−1.0

−2.5

−0.02

−1

−0.0125

−0.25

−1

0.7

0.1

0.006

0.1

0.004

0.1

+1.0

+2.5

LSB

+0.02

+1

+0.0125

+0.25

+1

% FS

ppm/°C

% FS

mV

µV/°C

mV

0.2

0.1

−0.125

+0.125

AC ACCURACY

f_IN= 1 kHz

Dynamic Range

Oversampled Dynamic Range

Signal-to-Noise Ratio (SNR)

91.3

dB

OSR = 4×, RES = 1 (decimal)

97.4

90.5

97.9

89

Rolling average OSR = 8×, RES = 1

(decimal)

f_IN= 100 kHz

88.6

−105

−106

−105

90

dB

Spurious-Free Dynamic Range (SFDR)

Total Harmonic Distortion (THD)

f_IN= 100 kHz

Signal-to-Noise-and-Distortion (SINAD) Ratio

Channel to Channel Isolation

88.5

−126

Rev. 0 | Page 3 of 31

AD7389-4

Data Sheet

V_CC= 3.0 V to3.6 V, V_LOGIC= 1.65 V to 3.6 V, internal V_REF= 2.5 V, T_A= −40°C to +125°C, no oversampling enabled, unless otherwise

noted.

Table 3.

Parameter

Test Conditions/Comments

Min

Typ

Max

Unit

SAMPLING DYNAMICS

Input Bandwidth

At −0.1 dB

At −3 dB

6.6

MHz

ns

ps

26.8

26.2

46.8

20

Aperture Delay

Aperture Delay Match

Aperture Jitter

145

REFERENCE OUTPUT

V_REFOutput Voltage

V_REFTemperature Coefficient

V_REFNoise

−40°C to +125°C

2.495

2.5

2

7

2.505

10

V

ppm/°C

µV rms

DIGITAL INPUTS (SCLK, SDI, CS)

Logic Levels

Input Low Voltage (V_IL)

0.2 ×

V_LOGIC

V

Input High Voltage (V_IH)

Input Low Current (I_IL)

Input High Current (I_IH)

DIGITAL OUTPUTS (SDOA, SDOB, SDOC, SDOD/ALERT)

Output Coding

Output Low Voltage (V_OL)

Output High Voltage (V_OH)

Floating State Leakage Current

Floating State Output Capacitance

POWER SUPPLIES

0.8 × V_LOGIC

−1

V

µA

+1

Twos complement

0.4

V_LOGIC− 0.3

Bits

V

µA

pF

Current sink (I_SINK) = 300 µA

Current source (I_SOURCE)= −300 µA

1

10

V_CC

V_LOGIC

3.0

1.65

3.3

3.6

V

V_CCSupply Current (I_VCC

)

Normal Mode (Operational)

Normal Mode (Static)

Shutdown Mode

21

1.7

101

23

2

200

mA

µA

V_LOGICCurrent (I_VLOGIC

)

Analog inputs at positive full scale

Normal Mode (Static)

Normal Mode (Operational)

Shutdown Mode

10

3.7

10

200

4.1

200

nA

mA

nA

Power Dissipation

Total (P_TOTAL

)

89

98

mW

V_CCPower (P_VCC

)

Normal Mode (Operational)

Normal Mode (Static)

Shutdown Mode

75.6

6.1

363.6 720

83

7.2

mW

µW

V_LOGICPower (P_VLOGIC

)

Analog inputs at positive full scale

Normal Mode (Static)

Normal Mode (Operational)

Shutdown Mode

36

13.3

36

720

15

720

nW

mW

µW

Rev. 0 | Page 4 of 31

Data Sheet

AD7389-4

TIMING SPECIFICATIONS

V_CC= 3.0 V to3.6 V, V_LOGIC= 1.65 V to 3.6 V, V_REF= 2.5 V, T_A= −40°C to +125°C, unless otherwise noted. When referencing a single function of

ALERT

a multifunction pin in the parameters, only the portion of the pin name that is relevant to the specification is listed, such as

names of multifunction pins, refer to the Pin Configuration and Function Descriptions section.

. For full pin

Table 4.

Parameter

Min

500

5

Typ

Max

Unit

ns

Description

t_CYC

Time between conversions

CS falling edge to first SCLK falling edge

SCLK period

SCLK high time

SCLK low time

t_SCLKED

t_SCLK

t_SCLKH

t_SCLKL

12.5

5.5

20

ns

t_CSH

CS pulse width

t_QUIET

t_SDOEN

20

ns

Interface quiet time prior to conversion

CS Low to SDOA and SDOB enabled

V_LOGIC≥ 2.25 V

5.5

8

ns

1.65 V ≤ V_LOGIC< 2.25 V

t_SDOH

t_SDOS

3

SCLK rising edge to SDOA and SDOB hold time

SCLK rising edge to SDOA and SDOB setup time

V_LOGIC≥ 2.25 V

5.5

8

ns

1.65 V ≤ V_LOGIC< 2.25 V

t_SDOT

CS rising edge to SDOA and SDOB high impedance

SDI setup time prior to SCLK falling edge

SDI hold time after SCLK falling edge

SCLK rising edge to CS rising edge

Conversion time

t_SDIS

t_SDIH

t_SCLKCS

t_CONVERT

t_ACQUIRE

t_RESET

4

0

190

310

Acquire time

Valid time to start conversion after software reset (see Figure 33)

Valid time to start conversion after soft reset

Valid time to start conversion after hard reset

Supply active to conversion

250

800

ns

t_POWERUP

5

11

5

ms

First conversion allowed

Settled to within 1% with internal reference

Supply active to register read write access allowed

Exiting shutdown mode to conversion

Settled to within 1% with internal reference

Conversion time for first sample in oversampling (OS) normal mode

Conversion time for x^thsample in OS normal mode

Time from CS to ALERT indication

t_REGWRITE

t_STARTUP

11

10

ms

ns

t_CONVERT0

t_CONVERTx

t_ALERTS

6

8

t_CONVERT0+ (320 × (x – 1))

220

10

t_ALERTC

Time from CS to ALERT clear

t_{ALERTS_NOS}

20

Time from internal conversion with exceeded threshold to ALERT indication

Rev. 0 | Page 5 of 31

AD7389-4

Data Sheet

Timing Diagrams

t_CYC

t_SCLK

t_CSH

t_SCLKED

t_SCLKH

t_SCLKL

t_QUIET

t_SCLKCS

CS

SCLK

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

TRISTATE

SDOA

TRISTATE

DB₁₅

DB₁₄

DB₁₃

DB₁₂

DB₁₁

DB₁₀

DB₉

DB₈

DB₇

DB₆

DB₅

DB₄

DB₃

DB₂

DB₀

1

TRISTATE

SDOB

TRISTATE

t_SDOT

DB₁₅

DB₁₄

DB₁₃

DB₆

DB₄

DB₃

DB₂

t_SDOEN

t_SDOH

t_SDOS

SDI

DB₁₅

DB₁₄

DB₁₃

DB₁₂

DB₁₁

DB₁₀

DB₉

DB₈

DB₇

DB₆

DB₅

DB₄

DB₃

DB₂

DB₀

1

t_SDIS

t_SDIH

Figure 2. Serial Interface Timing Diagram

t_CONVERT

CS

CONVERSION

ACQUIRE

CONVERSION

ACQUIRE

t_ACQUIRE

Figure 3. Internal Conversion Acquire Timing

t_POWERUP

V

CC

CS

TIME TO ACCURATE CONVERSION

Figure 4. Power-Up Time to Conversion

t_REGWRITE

VCC

CS

REG

WRITE

SDI

Figure 5. Power-Up Time to Register Read Write Access

t_STARTUP

CS

SDI

SHUTDOWN

SHUTDOWN MODE

NORMAL

NORMAL MODE

ACCURATE CONVERSION

Figure 6. Shutdown Mode to Normal Mode Timing

t_CONVERT0

CS

INTERNAL

CONVERSION

ACQUIRE

CONVERSION

ACQUIRE

CONVERSION

ACQUIRE

CONVERSION

ACQUIRE

t_CONVERT1

t_CONVERT2

t_CONVERT3

t_CONVERTx

Figure 7. Conversion Timing During OS Normal Mode

Rev. 0 | Page 6 of 31

Data Sheet

AD7389-4

t_ALERTS

t_ALERTC

CS

SDOA

NO OVERSAMPLING OR

ROLLING AVERAGE OS

INTERNAL

ALERT

CONV

ACQ

CONV

ACQ

CONV

ACQ

CONV

ACQ

EXCEEDS THRESHOLD

CS

SDOA

NORMAL

OVERSAMPLING

INTERNAL

ALERT

C

A

C

A

C

A

C

A

C

A

C

A

C

A

C

A

C

A

C

A

C

A

C

A

C

A

C

A

C

A

C

A

EXCEEDS THRESHOLD

t_{ALERTS_NOS}

t_ALERTC

ALERT

Figure 8.

Timing

Rev. 0 | Page 7 of 31

AD7389-4

Data Sheet

ABSOLUTE MAXIMUM RATINGS

Table 5.

THERMAL RESISTANCE

Thermal performance is directly linked to printed circuit board

(PCB) design and operating environment. Careful attention to

PCB thermal design is required.

Parameter

Rating

V_CCto GND

V_LOGICto GND

−0.3 V to +4 V

θ_JAis the natural convection junction to ambient thermal

resistance measured in a one cubic foot sealed enclosure. θ_JCis

the junction to case thermal resistance.

Analog Input Voltage to GND

−0.3 V to V_REF+0.3 V, or

V_CC+ 0.3 V

−0.3 V to V_LOGIC+ 0.3 V

−0.3 V to V_CC+0.3 V

10 mA

Digital Input Voltage to GND

Digital Output Voltage to GND

REFOUT Input to GND

Input Current to Any Pin Except

Supplies

Table 6. Thermal Resistance

Package Type

CP-24-25¹

θ_JA

θ_JC

0.43²

Unit

48.4

°C/W

Temperature Range

Operating

Storage

¹Test Condition 1: thermal impedance simulated values are based on

JEDEC 2S2P thermal test board with four thermal vias. See JEDEC JESDS1.

²Test Condition 2: a cold plate attached to the package surface and measured

at the exposed pad.

−40°C to +125°C

−65°C to +150°C

150°C

Maximum Junction Temperature

ELECTROSTATIC DISCHARGE (ESD) RATINGS

Pb-Free Soldering Reflow

Temperature

260°C

The following ESD information is provided for handling of

ESD-sensitive devices in an ESD protected area only.

Stresses at or above those listed under Absolute Maximum

Ratings may cause permanent damage to the product. This is a

stress rating only; functional operation of the product at these

or any other conditions above those indicated in the

operational section of this specification is not implied.

Operation beyond the maximum operating conditions for

extended periods may affect product reliability.

Human body model (HBM) per ANSI/ESDA/JEDEC JS-001.

Field induced charge device model (FICDM) per

ANSI/ESDA/JEDEC JS-002.

ESD Ratings for AD7389-4

Table 7. AD7389-4, 24-Lead LFCSP

ESD Model

Withstand Threshold (V)

Class

3A

C3

HBM

FICDM

4000

1250

ESD CAUTION

Rev. 0 | Page 8 of 31

Data Sheet

AD7389-4

PIN CONFIGURATION AND FUNCTION DESCRIPTIONS

1

2

3

18

17

GND

CS

V

REFOUT

LOGIC

AD7389-4

16 GND

REGCAP

15 REFCAP

14 GND

V

4

5

CC

TOP VIEW

(Not to Scale)

GND

A

D– 6

IN

A

A+

IN

13

NOTES

1. EXPOSED PAD. THE EXPOSED PAD MUST BE

CONNECTED TO GROUND.

Figure 9. Pin Configuration

Table 8. Pin Function Descriptions

Pin No.

Mnemonic

Description

1, 5, 14, 16

2

3

GND

V_LOGIC

REGCAP

Ground Reference Point. These pins are the ground reference points for all circuitry on the device.

Logic Interface Supply Voltage, 1.65 V to 3.6 V. Decouple this pin to GND with a 1 µF capacitor.

Decoupling Capacitor Pin for Voltage Output from Internal Regulator. Decouple this pin to GND with a

1 µF capacitor. The voltage at this pin is 1.9 V typical.

4

V_CC

Power Supply Input Voltage. 3.0 V to 3.6 V. Decouple this pin to GND using a 1 µF capacitor.

Analog Inputs of ADC D. These analog inputs form a fully differential pair.

Analog Inputs of ADC C. These analog inputs form a fully differential pair.

Analog Inputs of ADC B. These analog inputs form a fully differential pair.

Analog Inputs of ADC A. These analog inputs form a fully differential pair.

6, 7

8, 9

10, 11

12, 13

15

A_IND−, A_IND+

A_INC−, A_INC+

A_INB−, A_INB+

A_INA−, A_INA+

REFCAP

Decoupling Capacitor Pin for Bandgap Reference. Decouple this pin to GND with a 0.1 μF capacitor. The

voltage at this pin is 2.5 V typical.

17

18

REFOUT

CS

Reference Output. Decoupling is required on this pin. Apply a 1 µF capacitor from this pin to GND.

Chip Select Input. Active low, logic input. This input provides the dual function of initiating conversions

on the AD7389-4 and framing the serial data transfer.

19

SDOA

Serial Data Output A. This pin functions as a serial data output pin to access the conversion results and

register contents.

20

21

22

23

SDOB

SDI

SCLK

SDOC

Serial Data Output B. This pin functions as a serial data output pin to access the conversion results.

Serial Data Input. This input provides the data written to the on-chip control registers.

Serial Clock Input. This serial clock input is for data transfers to and from the ADC.

Serial Data Output C. This pin functions as a serial data output pin to access the conversion results and

register contents.

24

SDOD/ALERT Serial Data Output D (SDOD). This pin functions as a serial data output to access the conversion results.

Alert Indication Output (ALERT).This pin operates as an alert going low to indicate that a conversion

result has exceeded a configured threshold.

This pin can operate as a serial data output pin or alert indication output.

Not applicable EPAD

Exposed Pad. The exposed pad must be connected to ground.

Rev. 0 | Page 9 of 31

AD7389-4

Data Sheet

TYPICAL PERFORMANCE CHARACTERISTICS

0

94

92

90

88

86

84

82

80

78

76

74

f_IN= 1kHz

INTERNAL REFERENCE VOLTAGE = 2.5V

SNR = 90.38dB

THD = –111.29dB

–20

SINAD = 90.35dB

= 2.5V (INTERNAL)

–40

V

REF

–60

–80

–100

–120

–140

–160

–180

1

10

100

FREQUENCY (kHz)

1000

0

200

400

600

800

1000

FREQUENCY (kHz)

Figure 10. Fast Fourier Transform (FFT), 1 kHz Input Tone, −0.5 dBFS, Internal

Reference = 2.5 V

Figure 13. SINAD vs. Frequency

94

96

94

92

90

88

86

84

82

80

INTERNAL REFERENCE VOLTAGE = 2.5V

92

90

88

86

84

82

80

78

76

74

1

10

100

1000

–40 –25 –10

5

20

35

50

65

80

95 110 125

FREQUENCY (kHz)

TEMPERATURE (°C)

Figure 11. SNR vs. Frequency

Figure 14. SNR vs. Temperature

–70

–75

–80

INTERNAL REFERENCE VOLTAGE = 2.5V

–85

–90

–80

–85

–95

–90

–100

–105

–110

–115

–120

–125

–130

–95

–100

–105

–110

–115

–120

1

10

100

1000

–40 –25 –10

5

20

35

50

65

80

95 110 125

FREQUENCY (kHz)

TEMPERATURE (°C)

Figure 12. THD vs. Frequency

Figure 15. THD vs. Temperature

Rev. 0 | Page 10 of 31

Data Sheet

AD7389-4

96

94

92

90

88

86

84

82

–40

–50

–60

–70

–80

–90

–100

–110

80

0.1

1

10

100

1000

–40 –25 –10

5

20

35

50

65

80

95 110 125

RIPPLE FREQUENCY (kHz)

TEMPERATURE (°C)

Figure 19. CMRR vs. Ripple Frequency

Figure 16. SINAD vs. Temperature

104

102

100

98

30

NORMAL AVERAGING OVERSAMPLING

RES = 1

RES = 0

V

= 2.5V (INTERNAL)

REF

I

VCC

LOGIC

25

20

15

10

5

96

94

92

90

88

86

84

0

1

2

4

8

16

32

0

0.5

1.0

1.5

2.0

OVERSAMPLING RATIO

THROUGHPUT RATE (MSPS)

Figure 20. SNR vs. Oversampling Ratio, Normal Averaging

Figure 17. Dynamic Current vs. Throughput Rate

100

98

96

94

92

90

88

86

84

40

35

30

25

20

15

10

5

ROLLING AVERAGING OVERSAMPLING

THROUGHPUT RATE = 2MSPS

REF

RES = 1

RES = 0

V

= 2.5V (INTERNAL)

I

VCC

VLOGIC

0

1

2

4

8

–40 –25 –10

5

20

35

50

65

80

95 110 125

OVERSAMPLING RATIO

TEMPERATURE (°C)

Figure 21. SNR vs. Oversampling Ratio, Rolling Average

Figure 18. Dynamic Current vs. Temperature

Rev. 0 | Page 11 of 31

AD7389-4

Data Sheet

200000

180000

160000

140000

120000

100000

80000

60000

40000

20000

0

1.0

182548

0.8

A

V

+ = A

= V

÷ 2

INX

REF

= 2.5V

0.6

REF

0.4

0.2

0

–0.2

–0.4

–0.6

–0.8

–1.0

41718

–1

37983

0

243

2

0

–4

–3

–2

0

1

3

4

–32000 –24000 –16000 –8000

0

8000 16000 24000 32000

CODE

Figure 22. INL vs. Code

Figure 24. DC Histogram Codes at Code Center

1.0

0.8

0.6

0.4

0.2

0

–0.2

–0.4

–0.6

–0.8

–1.0

–32000 –24000 –16000 –8000

0

8000 16000 24000 32000

CODE

Figure 23. DNL vs. Code

Rev. 0 | Page 12 of 31

Data Sheet

AD7389-4

TERMINOLOGY

Signal-to-Noise Ratio (SNR)

Differential Nonlinearity (DNL)

SNR is the ratio of the rms value of the actual input signal to

the rms sum of all other spectral components below the

Nyquist frequency, excluding harmonics and dc. The value for

SNR is expressed in decibels.

In an ideal ADC, code transitions are 1 LSB apart. DNL is the

maximum deviation from this ideal value. DNL is often

specified in terms of resolution for which no missing codes are

guaranteed.

Spurious-Free Dynamic Range (SFDR)

Integral Nonlinearity (INL)

INL is the deviation of each individual code from a line drawn

from negative full scale through positive full scale. The point

used as negative full scale occurs ½ LSB before the first code

transition. Positive full scale is defined as a level 1½ LSB

beyond the last code transition. The deviation is measured from

the middle of each code to the true straight line.

SFDR is the difference, in decibels (dB), between the rms

amplitude of the input signal and the peak spurious signal.

Total Harmonic Distortion (THD)

THD is the ratio of the rms sum of the first five harmonic

components to the rms value of a full-scale input signal and

is expressed in decibels.

Gain Error

Signal-to-Noise-and-Distortion (SINAD) Ratio

The first transition (from 100 … 000 to 100 …001) occurs at a

level ½ LSB above nominal negative full scale. The last

transition (from 011 … 110 to 011 … 111) occurs for an analog

voltage 1½ LSB below the nominal full scale. The gain error is

the deviation of the difference between the actual level of the

last transition and the actual level of the first transition from

the difference between the ideal levels.

SINAD is the ratio of the rms value of the actual input signal to

the rms sum of all other spectral components that are less than

the Nyquist frequency, including harmonics but excluding dc.

The value for SINAD is expressed in decibels.

Common-Mode Rejection Ratio (CMRR)

CMRR is the ratio of the power in the ADC output at the

frequency, f, to the power of a 200 mV p-p sine wave applied to

the common-mode voltage of A_INx+ and A_INx− of frequency, f.

CMRR is expressed in decibels.

Gain Error Drift

The gain error change due to a temperature change of 1°C.

Gain Error Matching

CMRR = 10log(P_{ADC_IN}/P_{ADC_OUT}

where:

_{ADC_IN}is the common-mode power at the frequency, f, applied

to the A_INx+ and A_INxinputs.

_{ADC_OUT}is the power at the frequency, f, in the ADC output.

)

Gain error matching is the difference in negative full-scale error

between the input channels and the difference in positive full-

scale error between the input channels.

P

Zero Error

P

Zero error is the difference between the ideal midscale voltage,

0 V, and the actual voltage producing the midscale output code,

0 LSB.

Aperture Delay

Aperture delay is the measure of the acquisition performance

CS

and is the time between the falling edge of the

when the input signal is held for a conversion.

input and

Zero Error Temperature Drift

Zero error temperature drift is the zero error change due to a

temperature change of 1°C.

Aperture Delay Match

Aperture delay match is the difference of the aperture delay

between each ADC channel.

Zero Error Match

Zero error match is the difference in zero error between the

input channels.

Aperture Jitter

Aperture jitter is the variation in aperture delay.

Rev. 0 | Page 13 of 31

AD7389-4

Data Sheet

THEORY OF OPERATION

When the ADC starts a conversion (see Figure 26), SW3 opens

and SW1 and SW2 move to Position B, causing the comparator

to become unbalanced. Both inputs are disconnected when the

conversion begins. The control logic and charge redistribution

DACs are used to add and subtract fixed amounts of charge

from the sampling capacitor arrays to bring the comparator back

into a balanced condition. When the comparator is rebalanced,

the conversion is complete. The control logic generates the

ADC output code. The output impedances of the sources

driving the A_INx+ and A_INx− pins must be matched. Otherwise,

the two inputs have different settling times, resulting in errors.

CIRCUIT INFORMATION

The AD7389-4 is a high speed, quad, fully differential, 16-bit, SAR

ADC. The device operates from a 3.0 V to 3.6 V power supply

and features throughput rates up to 2 MSPS.

The AD7389-4 contains four successive approximation ADCs,

and a serial interface with four separate data output pins. The

device is housed in a 24-lead LFCSP, offering the user

considerable space-saving advantages over alternative

solutions.

Data is accessed from the device via the serial interface. The

interface can be operated with two, four, or one serial output.

The AD7389-4 has an on-chip 2.5 V internal reference

(10 ppm/°C). If the internal reference is used elsewhere in the

system, the reference output must be buffered. The differential

analog input range for the AD7389-4 is V_CMV_REF/2.

CAPACITIVE

DAC

COMPARATOR

B

A

C

S

A

x+

x–

IN

SW1

SW2

CONTROL

LOGIC

SW3

S

A

B

A

The AD7389-4 features on-chip oversampling blocks to

improve performance. Normal averaging and rolling average

oversampling modes are available. Power-down options to

allow power saving between conversions are available.

Configuration of the device is implemented via the standard

serial interface, as described in the Interface section.

IN

V

REF

Figure 26. ADC Conversion Phase

ANALOG INPUT STRUCTURE

CONVERTER OPERATION

Figure 27 shows the equivalent circuit of the analog input struc-

ture of the AD7389-4. The four diodes provide ESD protection

for the analog inputs. Ensure that the analog input signals never

exceed the supply rails by more than 300 mV. Exceeding the limit

causes these diodes to become forward-biased and start

The AD7389-4 has four successive approximation ADCs, each

based around two capacitive DACs. Figure 25 and Figure 26

show simplified schematics of one of these ADCs in acquisition

and conversion phases, respectively. The ADC comprises

control logic, a SAR, and two capacitive DACs. In Figure 25

(the acquisition phase), SW3 is closed, SW1 and SW2 are in

Position A, the comparator is held in a balanced condition,

and the sampling capacitor (C_S) arrays can acquire the

differential signal on the input.

conducting into the substrate. These diodes can conduct up to

10 mA without causing irreversible damage to the device.

The C1 capacitors in Figure 27 are typically 3 pF and can

primarily be attributed to pin capacitance. The R1 resistors

are lumped components made up of the on resistance of the

switches. The value of these resistors is typically about 200 Ω.

The C2 capacitors are the ADC sampling capacitors with a

typical capacitance of 15 pF.

CAPACITIVE

DAC

COMPARATOR

C

B

A

S

A

x+

IN

V

CC

SW1

SW2

CONTROL

LOGIC

SW3

S

C2

D

A

B

R1

A

x–

IN

A

x+

IN

C1

V

REF

CAPACITIVE

DAC

V

CC

Figure 25. ADC Acquisition Phase

C2

D

R1

A

x–

IN

C1

Figure 27. Equivalent Analog Input Circuit,

Conversion Phase—Switches Open, Track Phase—Switches Closed

Rev. 0 | Page 14 of 31

Data Sheet

AD7389-4

ADC TRANSFER FUNCTION

The AD7389-4 uses a 2.5 V reference. The AD7389-4 converts

the differential voltage of the analog inputs (A_INx+ and A_INx−)

into a digital output.

011...111

011...110

011...101

The conversion result is MSB first, twos complement. The LSB

size is (2 × V_REF)/2^N, where N is the ADC resolution. The ADC

resolution is determined by the resolution of the device chosen

and if resolution boost mode is enabled. Table 9 outlines the

LSB size expressed in microvolts for different resolutions with a

2.5 V reference voltage.

100...010

100...001

100...000

The ideal transfer characteristic of the AD7389-4 is shown in

Figure 28.

–FSR

–FSR + 1LSB

+FSR – 1LSB

–FSR + 0.5LSB

+FSR – 1.5LSB

ANALOG INPUT

Figure 28. ADC Ideal Transfer Function (FSR = Full-Scale Range)

Table 9. LSB Size

Resolution (Bits)

2.5 V Reference (μV)

16

18

76.3

19.1

V+ = 5V

LDO

V–

LDO

1.65V

TO

3.5V

3.0V

TO

V+

3.6V

V

= V

÷ 2

CM

REF

10kΩ

V

= 2.5V

1µF

REF

1µF

V+

A

x+

IN

V

REF

REFOUT

V

CC

R

V

CM

0V

A

A+

A–

IN

V

LOGIC

C1

1µF

V–

V+

C2

AD7389-4

A

x–

IN

SDI

REF

IN

100Ω

V

SDOA

CM

0V

100Ω

DIGITAL HOST

(MICROPROCESSOR/FPGA)

SDOB

SCLK

CS

C1

EXPOSED

PAD

V–

A

C+

C–

D+

D–

IN

100Ω

SDOC

SDOD/ALERT

REGCAP

1µF

GND

REFCAP

0.1µF

NOTES

1. V– IS THE EXTERNAL SUPPLY VOLTAGE (–2.5 V) FOR THE DRIVER AMPLIFIER.

2. PLACE DECOUPLING CAPACITORS CLOSE TO (IDEALLY, RIGHT UP AGAINST)

THE DEVICE SUPPLY PINS AND REFERENCE PIN.

Figure 29. Typical Application Circuit

Rev. 0 | Page 15 of 31

AD7389-4

Data Sheet

APPLICATIONS INFORMATION

Figure 29 shows an example of a typical application circuit for

the AD7389-4. Decouple the V_CC, V_LOGIC, REGCAP, and

REFOUT pins with suitable decoupling capacitors as shown.

The exposed pad is a ground reference point for circuitry on

the device and must be connected to the board ground.

ADC driver can be supplied by a 5 V (V+) and a −2.5 V (V−)

derived from the inverting charge pump, the ADP5600, that

converts 5 V to −5 V, then to the ADP7182 for the low noise

voltage regulator to output −2.5 V. Two independent power

supply sources are derived from a low dropout (LDO) regulator

to power the V_CCsupply for the analog circuitry and the V_LOGIC

supply for the digital interface of the AD7389-4. A very low

quiescent current LDO regulator like the ADP166 is a suitable

supply with a fixed output voltage range from 1.2 V to 3.3 V for

typical V_CCand V_LOGIClevels. The V_CCsupply and the V_LOGIC

supply must be decoupled separately with a 1 µF capacitor.

Additionally, an internal LDO regulator supplies the AD7389-4.

The on-chip regulator provides a 1.9 V supply only for internal

use on the device. Decouple the REGCAP pin with a 1 µF

capacitor to GND.

A differential RC filter must be placed on the analog inputs to

ensure optimal performance is achieved. In a typical

application, R = 33 Ω, C1 = 68 pF, and C2 = 68 pF are

recommended. These RC combinations must be the same for

all channels of the AD7389-4.

The four differential channels of the AD7389-4 can accept an

input voltage range from 0 V to V_REFand have a wide common-

mode range to convert a variety of signals. These analog input

pins (A_INx ) can easily be driven with an amplifier. Table 10

lists the recommended driver amplifiers that can best fit and

add value to the application.

Power-Up

The AD7389-4 is not easily damaged by power supply

sequencing. V_CCand V_LOGICcan be applied in any sequence. The

external reference must be applied after V_CCand V_LOGICare

applied. Analog and digital signals must be applied after the

external reference is applied.

The performance of the AD7389-4 device can be impacted by

noise on the digital interface. This impact is dependent on-board

layout and design. Keep a minimal distance of the digital line to

the digital interface or place a 100 Ω resistor in series and close

ALERT

to the SDOA, SDOB, SDOC, and SDOD/

pins to reduce

The AD7389-4 requires t_POWERUPfrom applying V_CCand V_LOGIC

until the ADC conversion results are stable. Interfacing with

the AD7389-4 prior to the setup time elapsing does not have a

negative impact on ADC operation. See Figure 4 for the

recommended signal condition during power-up. It is highly

recommended to issue a software reset after power-up (see the

Software Reset section for details).Conversion results are not

guaranteed to meet data sheet specifications during this time,

however.

noise from the digital interface coupling of the AD7389-4.

The AD7389-4 uses an internal 2.5 V reference voltage. When

this reference voltage is used for other circuits externally, for

example as a common-mode voltage for the driver amplifier, it

is recommended to use an external buffer amplifier like the

ADA4807-2.

POWER SUPPLY

For a typical application, the AD7389-4 circuitry shown in

Figure 29 can be driven from a 5 V (V+) supply to power the

system. The 5 V (V+) can be supplied from the ADP7104. The

Table 10. Signal Chain Components

Companion Devices

Part Name

Description

Typical Application

ADC Driver

ADA4896-2 1 nV/√Hz, rail-to-rail output amplifier

Precision, low noise, high frequency

ADA4940-2 Ultra low power, full differential, low distortion amplifier

ADA4807-2 1 mA, rail-to-rail output amplifier

Precision, low density, low power

Precision, low power, high frequency

3.0 V to 3.6 V supply for V_CCand V_LOGIC

5 V supply

−2.5 V supply for ADC driver amplifier

Voltage inverter for negative supply

Precision, low power, high frequency

LDO Regulator

ADP166

Very low quiescent, 150 mA, LDO regulator

500mA Low Noise, CMOS LDO regulator

Low noise line regulator

ADP7104

ADP7182

ADP5600

Interleaved inverting charge pump with negative LDO

Reference Buffer

ADA4807-2 1 mA, rail-to-rail output amplifier

Rev. 0 | Page 16 of 31

Data Sheet

AD7389-4

MODES OF OPERATION

The AD7389-4 has several on-chip configuration registers for

controlling the operational mode of the device.

before the register updates. That is, after writing to the OSR

bits, two conversion cycles take place before the conversion

results clock out with the updated OSR bits. The oversampling

ratio of the digital filter is controlled using the oversampling

bits, OSR (see Table 11).

OVERSAMPLING

Oversampling is a common method used in analog electronics

to improve the accuracy of the ADC result. Multiple samples of

the analog input are captured and averaged to reduce the noise

component from quantization noise and thermal noise (kTC

noise) of the ADC. The AD7389-4 offers an oversampling

function on-chip. The AD7389-4 has two user configurable

oversampling modes: normal averaging and rolling average.

Table 11 provides the oversampling bit decoding to select the

different oversample rates. The output result is decimated to

16-bit resolution. If required, additional resolution can be

achieved by configuring the resolution boost bit (RES) in the

Configuration 1 register. See the Resolution Boost section for

further details.

The oversampling functionality is configured by programming

the OS_MODE bit and OSR bits in the Configuration 1

register.

The number of samples (n), defined by the OSR bits, are taken

and added together, and the result is divided by n. The initial

CS

ADC conversion is initiated by the falling edge of

and the

Normal Averaging Oversampling

AD7389-4 controls all subsequent samples in the oversampling

sequence internally. The sampling rate of the additional n

samples at the device maximum sampling rate is 2 MSPS. The

data is ready for readback on the next serial interface access.

After the averaging technique is applied, the sample data used

in the calculation is discarded. This process is repeated every

time the application needs a new conversion result and is

Normal averaging oversampling mode can be used in

applications where slower output data rates are allowed and

where higher SNR or dynamic range is desirable. Normal

averaging involves taking a number of samples, adding them

together and dividing the result by the number of samples

taken. This result is then output from the device. The sample

data is cleared when the process completes.

CS

initiated by the next falling edge of

.

Normal averaging oversampling mode is configured by setting

the OS_MODE bit to Logic 0 and having a valid nonzero value

in the OSR bits. Writing to the OSR bits has a two-cycle latency

As the output data rate is reduced by the oversampling ratio,

the serial peripheral interface (SPI) SCLK frequency required to

transmit the data is reduced accordingly.

Table 11. Normal Averaging Oversampling Overview

SNR with 2.5 V Internal Reference (dB Typical)

OSR, Bits[2:0]

OS Ratio

RES = 0

90

RES = 1

90

93.4

96.5

99.2

Data Output Rate (kSPS Maximum)

000

001

010

011

100

101

No OS

2

4

8

16

32

2000

1500

750

375

187.5

93.75

92.3

94.1

95.6

96.4

96.7

100.5

101.7

CS

S

INTERNAL

ACQ

1

2

n

1

2

n

SDOA

SDOB

DON'T CARE

t0 RESULT

DON'T CARE

t0 RESULT

CONVERT START AT t₀

CONVERT START AT t₁

Figure 30. Normal Averaging Oversampling Operation

Rev. 0 | Page 17 of 31

AD7389-4

Data Sheet

bit in the Configuration 1 register. See the Resolution Boost

section for further details.

Rolling Average Oversampling

Rolling average oversampling mode can be used in applications

where higher output data rates are required and where a higher

SNR or dynamic range is desirable. Rolling averaging involves

taking a number of samples, adding them together, and

dividing the result by the number of samples taken. This result

is then output from the device. The sample data is not cleared

when the process completes. The rolling oversampling mode

uses a first in, first out (FIFO) buffer of the most recent samples

in the averaging calculation, allowing the ADC throughput rate

and output data rate to stay the same.

In rolling average oversampling mode, all ADC conversions are

CS

controlled and initiated by the falling edge of . When a

conversion is complete, the result is loaded into the FIFO. The

FIFO length is 8, regardless of the oversampling ratio set. The

FIFO is filled on the first conversion after a power-on reset

(POR), on the first conversion after a software controlled hard

or soft reset. A new conversion result is shifted into the FIFO

on completion of every ADC conversion regardless of the status

of the OSR bits and the OS_MODE bit. This conversion allows

a seamless transition from no oversampling to rolling average

oversampling, or different rolling average oversampling ratios

without waiting for the FIFO to fill.

Rolling average oversampling mode is configured by setting the

OS_MODE bit to Logic 1 and having a valid nonzero value in

the OSR bits. The oversampling ratio of the digital filter is

controlled using the oversampling bits, OSR (see Table 12).

The number of samples, n, defined by the OSR bits are taken

from the FIFO, added together and the result is divided by n.

Table 12 provides the oversampling bit decoding to select the

different oversample rates. The output result is decimated to

16-bit resolution for the AD7389-4. If required, additional

resolution can be achieved by configuring the resolution boost

Table 12. Rolling Average Oversampling Overview

SNR with 2.5 V Internal Reference (dB Typical)

OSR, Bits[2:0]

OS Ratio

RES = 0

90.2

91.5

93.2

94.7

RES = 1

90.2

92.4

95

97.3

Data Output Rate (kSPS Ma2ximum)

000

001

010

011

110

111

No OS

2

4

8

Invalid

2000

Not applicable

V

CC

CS

INTERNAL

S1

ACQ

S2

ACQ

S3

ACQ

S4

ACQ

S5

ACQ

S6

ACQ

S7

ACQ

ENABLE OS = 2

S1

ENABLE OS = 4

SDI

SDOA

SDOB

(F + F + F + F )/4

DON’T CARE

S2

(F + F )/2

1

2

3

4

1

2

1

2

1

2

FIFO

1

2

3

4

5

6

7

8

S

1

2

3

4

5

6

7

8

S

1

S

1

2

3

4

5

6

7

8

S

1

2

3

4

5

6

7

8

S

1

2

3

4

5

6

7

8

S

1

2

3

4

5

6

7

8

S

1

2

1

3

2

1

4

3

2

1

5

4

3

2

1

6

5

4

3

2

1

7

6

5

4

3

2

1

S

2

3

4

5

6

7

8

Figure 31. Rolling Average Oversampling Mode Configuration

Rev. 0 | Page 18 of 31

Data Sheet

AD7389-4

ALERT

CS

pin is cleared with a falling edge of . Issuing a

SDOD/

RESOLUTION BOOST

software reset also clears the alert status in the alert indication

register.

The default resolution and output data size for the AD7389-4 is

16 bits. When the on-chip oversampling function is enabled the

performance of the ADC can exceed the default resolution. To

accommodate the performance boost achievable, it is possible

to enable an additional two bits of resolution. If the RES bit in

the Configuration 1 register is set to Logic 1 and the AD7389-4

is in a valid oversampling mode, the conversion result size for

the AD7389-4 is 18 bits. In this mode, 18 SCLK cycles are

required to propagate the data for the AD7389-4.

ALERT

See Figure 8 for the

timing diagram.

POWER MODES

The AD7389-4 has two power modes that can be set in the

Configuration 1 register: normal mode and shutdown mode.

These modes of operation provide flexible power management

options, allowing optimization of the power dissipation and

throughput rate ratio for different application requirements.

ALERT

Program the PMODE bit in the Configuration 1 register to

configure the power modes in the AD7389-4. Set PMODE to

Logic 0 for normal mode and Logic 1 for shutdown mode.

The alert functionality is an out of range indicator and can be

used as an early indicator of an out of bounds conversion

result. An alert event triggers when the value in the conversion

result register exceeds the alert high limit value in the alert high

threshold register or falls below the alert low limit value in the

alert low threshold register. The alert high threshold register

and the alert low threshold register are common to all ADCs.

When setting the threshold limits, the alert high threshold must

always be greater than the alert low threshold. Detailed alert

information is accessible in the alert indication register.

Normal Mode

Keep the AD7389-4 in normal mode to achieve the fastest

throughput rate. All blocks within the AD7389-4 always remain

fully powered and an ADC conversion can be initiated by a

CS

falling edge of

when required. When the AD7389-4 is not

converting, it is in static mode and power consumption is

automatically reduced. Additional current is required to

perform a conversion. Therefore, power consumption of the

AD7389-4 scales with throughput.

The register contains two status bits per ADC, one corresponding

to the high limit, and the other to the low limit. A logical OR of

alert signals for all ADCs creates a common alert value. This

Shutdown Mode

ALERT

value can be configured to drive out on the

function of

pin is configured as

by configuring the following bits in the Configuration 1

register and the Configuration 2 register:

When slower throughput rates and lower power consumption

are required, use shutdown mode by either powering down the

ADC between each conversion or by performing a series of

conversions at a high throughput rate and then powering down

the ADC for a relatively long duration between these burst

conversions. When the AD7389-4 is in shutdown mode, all

analog circuitry powers down. The serial interface remains

active during shutdown mode to allow the AD7389-4 to exit

shutdown mode.

ALERT ALERT

the SDOD/

ALERT

pin. The SDOD/



Set the SDO bits to any value other than 0b10.

Set the ALERT_EN bit to 1.

Set a valid value in the alert high threshold register and the

alert low threshold register.

The alert indication function is available in oversampling

(rolling average, normal averaging, and in nonoversampling

modes).

To enter shutdown mode, write to the power mode

configuration bit, PMODE, in the Configuration 1 register.

The AD7389-4 shuts down, and current consumption reduces.

To exit shutdown mode and return to normal mode, set the

PMODE bit in the Configuration 1 register to Logic 0. All

register configuration settings remain unchanged entering or

leaving shutdown mode. After exiting shutdown mode, allow

sufficient time for the circuitry to turn on before starting a

conversion.

ALERT

The alert function of the SDOD/

pin updates at the end

ALERT

of conversion. The alert indication status bits in the

register are updated as well and must be read before the end of

the next conversion.

Bits[7:0] in the alert indication register are cleared by reading

the alert indication register contents. The alert function of the

CS

SCLK

1

2

3

14

15

16

17

18

SDOA

SDOB

DB

0

17

16

15

4

3

2

1

SDI

DB

0

15

14

13

2

1

Figure 32. Resolution Boost

Rev. 0 | Page 19 of 31

AD7389-4

Data Sheet

and FIFO are flushed. The alert indication register is cleared.

The reference and LDO regulator remain powered.

INTERNAL REFERENCE

The AD7389-uses a low noise, low drift (10 ppm/°C) 2.5 V

buffered internal reference during conversion. The internal

2.5 V reference of the AD7389-4 allows excellent performance

with typically 90.5 dB of SNR. When using the internal 2.5 V

reference for an external circuit, the internal 2.5 V reference can

be accessed via the REFOUT pin. It is recommended to add a

buffer, such as the ADA4807-2, when using the 2.5 V internal

reference as a source for a common-mode voltage (V_CM).

Connecting a 1 µF capacitor to the REFOUT pin is

recommended.

t_RESET

CS

SDI

SOFTWARE RESET

Figure 33. Software Reset Operation

A hard reset, in addition to the blocks reset by a soft reset,

resets all user registers to the default status, resets the reference

buffer, and resets the internal oscillator block.

DIAGNOSTIC SELF TEST

SOFTWARE RESET

The AD7389-4 runs a diagnostic self test after a POR or after a

software hard reset to ensure the correct configuration is

loaded into the device.

The AD7389-4 has two reset modes: a soft reset and a hard

reset. A reset is initiated by writing to the reset bits in the

Configuration 2 register.

The result of the self test is displayed in the SETUP_F bit in the

alert indication register. If the SETUP_F bit is set to Logic 1, the

diagnostic self test has failed. If the test fails, perform a software

hard reset to reset the AD7389-4 registers to the default status.

A soft reset maintains the contents of the configurable registers

but refreshes the interface and the ADC blocks. Any internal

state machines are reinitialized, and the oversampling block

t_STARTUP

CS

SDI

SHUTDOWN

SHUTDOWN MODE

NORMAL

NORMAL MODE

ACCURATE CONVERSION

Figure 34. Shutdown Mode Operation

Rev. 0 | Page 20 of 31

Data Sheet

AD7389-4

INTERFACE

The interface to the AD7389-4 is via a serial interface. The

The conversion result is shifted out of the device as a 16-bit

result for the AD7389-4. The MSB of the conversion result is

CS

out of the device under the control of the serial clock (SCLK)

input. The data is shifted out on the rising edge of SCLK, and

the data bits are valid on both the falling edge and the rising

CS

interface consists of , SCLK, SDOA, SDOB, SDOC, and

shifted out on the

falling edge. The remaining data is shifted

SDOD, and SDI. When referencing a single function of a

multifunction pin, only the portion of the pin name that is relevant

to the specification is listed, such as SDOD. For full pin names of

multifunction pins, refer to the Pin Configuration and Function

Descriptions section.

CS

edge. After the final SCLK falling edge, take

high again to

return the serial data output pins to a high impedance state.

CS

The

signal frames a serial data transfer and initiates an ADC

CS

The number of SCLK cycles to propagate the conversion results

on the serial data output pins is dependent on the serial mode

of operation configured and if resolution boost mode is enabled

(see Figure 35 and Table 13 for details). If CRC reading is

enabled, additional SCLK pulses are required to propagate the

CRC information. See the CRC section for more details.

conversion process. The falling edge of

puts the track-and-

hold into hold mode, at which point the analog input is

sampled and the bus is taken out of three-state. The ADC

conversion operation is driven internally by an on-board

oscillator and is independent of the SCLK signal.

The SCLK signal synchronizes data in and out of the device via

the SDOA, SDOB, SDOC, SDOD, and SDI signals. A minimum

of 16 SCLK cycles are required for a write to or read from a

register. The minimum numbers of SCLK cycles for a

conversion read is dependent on the resolution of the device

and the configuration settings (see Table 13).

CS

Because the

signal initiates a conversion as well as framing

the data, any data access must be completed within a single frame.

Table 13. Number of SCLK Cycles (n) Required for Reading

Conversion Results

Interface

Configuration

Resolution

Boost Mode

CRC

Read

No. of SCLK

Cycles

The ADC conversion operation is driven internally by an

on-board oscillator and is independent of the SCLK signal.

4-Wire

2-Wire

1-Wire

Disabled

Enabled

Disabled

Enabled

Disabled

Enabled

Disabled 16

Enabled 24

Disabled 18

Enabled 26

Disabled 32

Enabled 40

Disabled 36

Enabled 44

Disabled 64

Enabled 72

Disabled 72

Enabled 80

The AD7389-4 has four serial output signals: SDOA, SDOB,

SDOC, and SDOD. Programming the SDO bits in the

Configuration 2 register configures 2-wire, 1-wire, or 4-wire

mode. To achieve the highest throughput of the device, it is

required to use either the 2-wire or 4-wire mode to read the

conversion results. If a reduced throughput is required or

oversampling is used, it is possible to use 1-wire mode, SDOA

signal only, for reading conversion results.

Configuring cyclic redundancy check (CRC) operation for SPI

reads, SPI writes, and oversampling mode with resolution boost

mode enabled can alter the operation of the interface. Refer to

the CRC section to ensure correct operation.

Serial 4-Wire Mode

READING CONVERSION RESULTS

Configure 4-wire mode by setting the SDO bits to 0b10 in the

Configuration 2 register. In 4-wire mode, the conversion results

for ADC A is output on SDOA, ADC B on SDOB, ADC C on

SDOC, and ADC D on SDOD.

CS

The

signal initiates the conversion process. A high to low

CS

transition on the

signal initiates a simultaneous conversion

of the four ADCs, ADC A, ADC B, ADC C, and ADC D. The

AD7389-4 has a one-cycle readback latency. Therefore, the

conversion results are available on the next SPI access. Then,

Serial 2-Wire Mode

Configure 2-wire mode by setting the SDO bits to 0b00 in the

Configuration 2 register. In 2-wire mode, the conversion results

for ADC A and ADC C are output on SDOA. The conversion

result for ADC B and ADC D are output on SDOB.

CS

take the

signal low, and the conversion result clocks out on

the serial data output pins. The next conversion is also initiated

at this point.

CS

1

n – 2

n – 1

n

1

2

3

SCLK

SDOx

1

CONVERSION RESULTS

CONSULT TABLE 12 FOR VALUES FOR n, THE NUMBER OF SCLK PULSES REQUIRED.

Figure 35. Reading Conversion Results

Rev. 0 | Page 21 of 31

AD7389-4

Data Sheet

Serial 1-Wire Mode

LOW LATENCY READBACK

In applications where slower throughput rates are allowed or

normal averaging oversampling is used, the serial interface can

be configured to operate in 1-wire mode. In 1-wire mode, the

conversion results from ADC A, ADC B, ADC C, and ADC D

are output on SDOA. Additional SCLK cycles are required to

propagate all data. ADC A data is output first followed by the

ADC B, ADC C, and ADC D conversion results.

The interface on the AD7389-4 has a one-cycle latency as

shown in Figure 36. For applications that operate at lower

throughput rates the latency of reading the conversion result

can be reduced. After the conversion time (t_CONVERT) elapses, a

CS

second

pulse after the initial

pulse that initiated the

conversion can be used to read back the conversion result. This

operation is shown in Figure 39.

S

0

1

2

3

CS

SDOA

SDOB

SDOC

SDOD

SDI

S

INVALID

NOP

1A

1B

1C

1D

0A

0B

0C

0D

NOP

Figure 36. Read Conversion Results, 4-Wire Mode

S

3

0

1

2

CS

SDOA

SDOB

SDI

INVALID

S

0A

0C

1A

1C

INVALID

NOP

0B

0D

1B

1D

NOP

Figure 37. Reading Conversion Results, 2-Wire Mode

S

3

0

1

2

CS

SDOA

SDI

S

0D

S

1D

INVALID

NOP

0A

0B

0C

1A

1B

1C

NOP

Figure 38. Read Conversion Results, 1-Wire Mode

CS

CNV

DON'T CARE

ACQ

CNV

DON'T CARE

RESULT

ACQ

INTERNAL

n

n + 1

SDOA

SDOB

RESULT

n

n + 1

SCLK

TARGET SAMPLE PERIOD

Figure 39. Low Throughput Low Latency

Rev. 0 | Page 22 of 31

Data Sheet

AD7389-4

function for SPI writes to prevent unexpected changes to the

device configuration but do not enable it on SPI reads to

maintain a higher throughput rate. The CRC feature is controlled

by programming of the CRC_W bit and CRC_R bit in the

Configuration 1 register.

READING FROM DEVICE REGISTERS

All registers in the device can be read over the serial interface. A

register read is performed by issuing a register read command

followed by an additional SPI command that can be either a

valid command or no operation command (NOP). The format

for a read command is shown in Table 16. Bit D15 must be set

to 0 to select a read command. Bits[D14:D12] contain the

register address. The subsequent 12 bits, Bits[D11:D0], are

ignored.

CRC Read

If enabled, a CRC consisting of an 8-bit word is appended to the

conversion result or register reads. The CRC is calculated on the

conversion result for ADC A, ADC B, ADC C, and ADC D, and

is output on SDOA. A CRC is also calculated and appended to

register read outputs.

WRITING TO DEVICE REGISTERS

All the read/write registers in the AD7389-4 can be written to

over the serial interface. The length of an SPI write access is

determined by the CRC write function. An SPI access is 16-bit

if CRC write is disabled and 24-bit when CRC write is enabled.

The format for a write command is shown in Table 16. Bit D15

must be set to 1 to select a write command. Bits[D14:D12] contain

the register address. The subsequent 12 bits, Bits[D11:D0],

contain the data to be written to the selected register.

The CRC read function can be used in 2-wire SPI mode, 1-wire

SPI mode, 4-wire SPI mode, and resolution boost mode.

CRC Write

To enable the CRC write function, the CRC_W bit in the

Configuration 1 register must be set to 1. To set the CRC_W bit

to 1 to enable the CRC feature, a valid CRC must be appended

to the request frame.

CRC

After the CRC feature is enabled, all register write requests are

ignored unless they are accompanied by a valid CRC command.

A valid CRC is required to both enable and disable the CRC

write feature.

The AD7389-4 has CRC checksum modes that can be used to

improve interface robustness by detecting errors in data

transmissions. The CRC feature is independently selectable for

SPI interface reads and writes. For example, enable the CRC

S

4

0

1

2

3

CS

SDI

NOP

READ REG 1

READ REG 2

REG 1 DATA

NOP

SDOA

INVALID

RESULT S

REG 2 DATA

RESULT S

3

0

SDOB

SDOC

SDOD

RESULT S

3

0

Figure 40. Register Read

S

2

S

3

0

1

CS

SDI

NOP

WRITE REG 1

WRITE REG 2

NOP

SDOx

INVALID

RESULT S

2

0

1

Figure 41. Register Write

Rev. 0 | Page 23 of 31

AD7389-4

Data Sheet

adjacent to the leftmost Logic 1 of the new result, and the

CRC Polynomial

procedure is repeated. This process repeats until the original

data is reduced to a value less than the polynomial, which is the

8-bit checksum.

For CRC checksum calculations, the following polynomial is

always used: x⁸+ x²+ x + 1.

To generate the checksum, the 16-bit data conversion result of

the four channels are combined to produce a 64-bit data

stream. The 8 MSBs of the 64-bit data are inverted and then the

data is appended by eight bits to create a number ending in

eight Logic 0s. The polynomial is aligned such that its MSB is

adjacent to the leftmost Logic 1 of the data. An exclusive OR

(XOR) function is applied to the data to produce a new, shorter

number. The polynomial is again aligned such that its MSB is

For example, the AD7389-4 polynomial is 100000111. Let the

original data of four channels be 0xAAAA, 0x5555, 0xAAAA,

and 0x5555. The eight MSBs of the data are inverted. The data

is then appended to include eight 0s on right. In the final XOR

operation, the reduced data is less than the polynomial.

Therefore, the remainder is the CRC for the assumed data.

Table 14. Example CRC Calculation for 4-Channel, 16-Bit Data

Data

1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 X¹X¹X¹X¹X¹X¹X¹X¹

Process Data 0 1 0 1 0 1 0 1 1 0 1 0 1 0 1 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

CRC

0

¹X means don’t care.

Rev. 0 | Page 24 of 31

Data Sheet

AD7389-4

16 + 16 + 8 = 40 BITS

RESULT C

CRC

SDOA

SDOB

RESULT A

A,B,C,D

2-WIRE 16-BIT

RESULT B

RESULT D

16 + 16 + 16 + 16 + 8 = 72 BITS

CRC

A,B,C,D

RESULT A

RESULT B

RESULT C

RESULT D

1-WIRE 16-BIT

2-WIRE 18-BIT

SDOA

18 + 18 + 8 = 44 BITS

RESULT C

CRC

SDOA

SDOB

RESULT A

RESULT B

A,B,C,D

RESULT D

18 + 18 + 18 + 18 + 8 = 80 BITS

RESULT B RESULT C

CRC

SDOA

RESULT A

RESULT D

A,B,C,D

1-WIRE 18-BIT

4-WIRE 16-BIT

16 + 8 = 24 BITS

RESULT A

CRC

SDOA

SDOx

A,B,C,D

RESULT x

18 + 8 = 26 BITS

RESULT A

CRC

SDOA

SDOx

A,B,C,D

4-WIRE 18-BIT

RESULT x

16 + 8 = 24 BITS

REGISTER

CRC

REGISTER x

SDOA

SDI

REG x

READ RESULT

16 + 8 = 24 BITS

REGISTER

READ REQUEST

CRC

REGISTER x

REG x

16 + 8 = 24 BITS

REGISTER

WRITE

CRC

SDI

WRITE REGISTER x

REG x

Figure 42. CRC Operation

Rev. 0 | Page 25 of 31

AD7389-4

Data Sheet

REGISTERS

The AD7389-4 has user-programmable, on-chip registers for configuring the device. Table 15 shows a complete overview of the registers

available on the AD7389-4.

The registers are either read/write (R/W) or read only (R). Any read request to a write only register is ignored. Any write to a read only

register is ignored. Writes to the NOP registers and the reserved register are ignored. Any read request to the NOP registers or reserved

registers are considered a no operation and the data transmitted in the next SPI frame are the conversion results.

Table 15. Register Description

Bit 15

Bit 14

Bit 6

Bit 13

Bit 5

Bit 12

Bit 4

Bit 11

Bit 3

Bit 10

Bit 2

Bit 9

Bit 1

Bit 8

Bit 0

Reg Name

Bits

Bit 7

Reset

RW

0x1 Configuration 1 [15:8]

ADDRESSING

CRC_W

RESERVED

OS_MODE OSR, Bit 2

0x0000 R/W

[7:0]

0x2 Configuration 2 [15:8]

[7:0]

OSR, Bits[1:0]

CRC_R

ALERT_EN RES

RESERVED

PMODE

SDO

ADDRESSING

0x0000 R/W

RESET

0x3 Alert indication [15:8]

[7:0]

ADDRESSING

RESERVED

CRCW_F

SETUP_F

0x0000

R

AL_D_HIGH AL_D_LOW AL_C_HIGH AL_C_LOW AL_B_HIGH AL_B_LOW AL_A_HIGH AL_A_LOW

0x4 Alert low

threshold

[15:8]

[7:0]

ADDRESSING

ALERT_LOW, Bits[11:8]

0x0800 R/W

0x07FF R/W

ALERT_LOW, Bits[7:0]

ALERT_HIGH, Bits[7:0]

0x5 Alert high

threshold

[15:8]

[7:0]

ADDRESSING

ALERT_HIGH, Bits[11:8]

ADDRESSING REGISTERS

A serial register transfer on the AD7389-4 consists of 16 SCLK cycles. The four MSBs written to the device are decoded to determine

which register is addressed. The four MSBs consist of the register address (REGADDR), Bits[2:0], and the read/write bit (WR). The

register address bits determine which on-chip register is selected. If the addressed register is a valid write register, the read/write bit

determines whether the remaining 12 bits of data on the SDI input are loaded into the addressed register. If the WR bit is 1, the bits load

into the register addressed by the register select bits. If the WR bit is 0, the command is seen as a read request. The addressed register

data is available to be read during the next read operation.

Table 16. Addressing Register Format

MSB

D15

WR

LSB

D0

D14

D13

D12

D11

D10

D9

D8

D7

D6

D5

D4

D3

D2

D1

REGADDR, Bits[2:0]

Data, Bits[11:0]

Table 17. Bit Descriptions for Addressing Registers

Bit

Mnemonic

Description

D15

WR

When a 1 is written to this bit, Bits[11:0] of this register are written to the register specified by REGADDR if it

is a valid address.

Alternatively, when a 0 is written, the next data sent out on the SDOA pin is a read from the designated

register if it is a valid address.

D14 to D12 REGADDR

When WR = 1, the contents of REGADDR determine the register for selection as outlined in Table 15.

When WR = 0 and the REGADDR bits contain a valid register address, the contents on the requested register

are output on the SDOA pin during the next interface access.

When WR = 0 and the REGADDR bits contain 0x0, 0x6, or 0x7, the contents on the SDI line are ignored. The

next interface access results in the conversion results being read back.

D11 to D0

Data

These bits are written into the corresponding register specified by the REGADDR bits when the WR bit = 1

and the REGADDR bits contain a valid address.

Rev. 0 | Page 26 of 31

Data Sheet

AD7389-4

CONFIGURATION 1 REGISTER

15 14 13 12 11 10

9

8

7

6

5

4

3

2

1

0

[15:12] ADDRESSING (R/W)

[0] PMODE (R/W)

Addressing.

Power-Down Mode.

[11:10] RESERVED

[1] RESERVED

[9] OS_MODE (R/W)

[2] RES (R/W)

Oversampling Mode.

Resolution.

[8:6] OSR (R/W)

[3] ALERT_EN (R/W)

Oversampling Ratio.

Enable Alert Indicator Function.

[5] CRC_W (R/W)

[4] CRC_R (R/W)

CRC Write.

CRC Read.

Table 18. Bit Descriptions for Configuration 1 Register

Bits Bit Name Description

Reset Access

[15:12] ADDRESSING Addressing. Bits[15:12] define the address of the relevant register. See the Addressing Registers 0x0

section for further details.

R/W

[11:10] RESERVED

Reserved.

0x0

R

9

OS_MODE

Oversampling Mode. Sets the oversampling mode of the ADC.

0: normal averaging.

R/W

1: rolling average.

[8:6]

OSR

Oversampling Ratio. Sets the oversampling ratio for all the ADCs in the relevant mode. Normal

averaging mode supports oversampling ratios of 2×, 4×, 8×, 16×, and 32×. Rolling average

mode supports oversampling ratios of 2×, 4×, and 8×.

0x0

R/W

000: disabled.

001: 2×.

010: 4×.

011: 8×.

100: 16×.

101: 32×.

110: disabled.

111: disabled.

5

CRC_W

CRC Write. Controls the CRC functionality for the SDI interface When setting this bit from a 0 to

a 1, the command must be followed by a valid CRC to set this configuration bit. If a valid CRC is

not received, the entire frame is ignored. If the bit is set to 1, it requires a CRC to clear it to 0.

0x0

R/W

0: no CRC function.

1: CRC function.

4

3

CRC_R

CRC Read. Controls the CRC functionality for the SDOx interface

0: no CRC function.

1: CRC function.

0x0

R/W

ALERT_EN

Enable Alert Indicator Function. This bit functions when the SDO bits = 01. Otherwise, the

ALERT_EN bit is ignored.

0: SDOB.

1: ALERT.

2

RES

Resolution. Sets the size of the conversion result data. If OSR = 0, these bits are ignored and the 0x0

resolution is set to default resolution.

R/W

0: normal resolution.

1: 2-bit higher resolution.

1

0

RESERVED

PMODE

Reserved.

0x0

R/W

Power-Down Mode. Sets the power modes.

0: normal mode.

1: shutdown mode.

Rev. 0 | Page 27 of 31

AD7389-4

Data Sheet

CONFIGURATION 2 REGISTER

15 14 13 12 11 10

9

8

7

6

5

4

3

2

1

0

[15:12] ADDRESSING(R/W)

[7:0] RESET (R/W)

Addressing

Reset

[11:10] RESERVED

[9:8] SDO (R/W)

SDO

Table 19. Bit Descriptions for Configuration 2 Register

Bits Bit Name Description

Reset Access

[15:12] ADDRESSING Addressing. Bits[15:12] define the address of the relevant register. See the Addressing

Registers section for further details.

0x0

R/W

[11:10] RESERVED

Reserved.

0x0

R

R/W

[9:8]

SDO

SDO. Conversion Results Serial Data Output

00: 2-wire. Conversion data are output on both SDOA and SDOB.

01: 1-wire. Conversion data are output on SDOA only.

10: 4-wire. Conversion data are output on SDOA, SDOB, SDOC, and SDOD/ALERT.

11: 1-wire. Conversion data are output on SDOA only.

Reset.

[7:0]

RESET

0x0

R/W

0x3C: performs a soft reset. Refreshes some blocks. Register contents remain unchanged.

Clears alert indication register and flushes any oversampling stored variables or active state

machine.

0xFF: performs a hard reset. Resets all possible blocks in the device. Registers contents are

set to defaults. All other values are ignored.

ALERT INDICATION REGISTER

15 14 13 12 11 10

9

8

7

6

5

4

3

2

1

0

[15:12] ADDRESSING (R)

[0] AL_A_LOW (R)

Addressing.

Alert A Low.

[11:10] RESERVED

[1] AL_A_HIGH (R)

Alert A High.

[9] CRCW_F (R)

CRC Error.

[2] AL_B_LOW (R)

Alert B Low.

[8] SETUP_F (R)

Load Error.

[3] AL_B_HIGH (R)

Alert B High.

[7] AL_D_HIGH (R)

Alert D High.

[4] AL_C_LOW (R)

Alert C Low.

[6] AL_D_LOW (R)

Alert D Low.

[5] AL_C_HIGH (R)

Alert C High.

Table 20. Bit Descriptions for Alert Indication Register

Bits Bit Name Description

Reset Access

[15:12] ADDRESSING Addressing. Bits[15:12] define the address of the relevant register. See the Addressing

Registers section for further details.

0x0

R

[11:10] RESERVED

Reserved.

0x0

R

9

CRCW_F

CRC Error. Indicates that a register write command failed due to a CRC error. This fault bit is

sticky and remains set until the register is read

0: no CRC error.

1: CRC error.

8

SETUP_F

Load Error. The SETUP_F indicates that the device configuration data did not load correctly

on startup. This bit does not clear on an alert indication register read. A hard reset via the

Configuration 2 register is required to clear this bit and restart the device setup again.

0: no setup error.

1: setup error.

Alert D High. The alert indication high bit indicates if a conversion result for the respective

input channel exceeds the value set in the alert high threshold register. This fault bit is sticky

and remains set until the register is read.

0x0

R

7

AL_D_HIGH

1: alert indication.

0: no alert indication.

Rev. 0 | Page 28 of 31

Data Sheet

AD7389-4

Bits

Bit Name

Description

Reset Access

6

AL_D_LOW

AL_C_HIGH

AL_C_LOW

AL_B_HIGH

AL_B_LOW

AL_A_HIGH

AL_A_LOW

Alert D Low. The alert indication low bit indicates if a conversion result for the respective

input channel exceeds the value set in the alert low threshold register. This fault bit is sticky

and remains set until the register is read.

0: no alert indication.

1: alert indication.

Alert C High. The alert indication high bit indicates if a conversion result for the respective

input channel exceeds the value set in the alert high threshold register. This fault bit is sticky

and remains set until the register is read.

0x0

R

5

4

3

2

1

0

1: alert indication.

0: no alert indication.

Alert C Low. The alert indication low bit indicates if a conversion result for the respective

input channel exceeds the value set in the alert low threshold register. This fault bit is sticky

and remains set until the register is read.

1: alert indication.

0: no alert indication.

Alert B High. The alert indication high bit indicates if a conversion result for the respective

input channel exceeds the value set in the alert high threshold register. This fault bit is sticky

and remains set until the register is read.

1: alert indication.

0: no alert indication.

Alert B Low. The alert indication low bit indicates if a conversion result for the respective

input channel exceeds the value set in the alert low threshold register. This fault bit is sticky

and remains set until the register is read.

1: alert indication.

0: no alert indication.

Alert A High. The alert indication high bit indicates if a conversion result for the respective

input channel exceeds the value set in the alert high threshold register. This fault bit is sticky

and remains set until the register is read.

0: no alert indication.

1: alert indication.

Alert A Low. The alert indication low bit indicates if a conversion result for the respective

input channel exceeds the value set in the alert low threshold register. This fault bit is sticky

and remains set until the register is read.

1: alert indication.

0: no alert indication.

ALERT LOW THRESHOLD REGISTER

15 14 13 12 11 10

9

8

7

6

5

4

3

2

1

0

1

0

[15:12] ADDRESSING (R/W)

[11:0] ALERT_LOW (R/W)

Addressing

Alert Low

Table 21. Bit Descriptions for Alert Low Threshold Register

Bits Bit Name Description

[15:12] ADDRESSING Addressing. Bits[15:12] define the address of the relevant register. See the Addressing

Registers section for further details.

Reset Access

0x0 R/W

[11:0]

ALERT_LOW

Alert Low. Bits[11:0] from ALERT_LOW move to the MSBs of the internal alert low register,

D[15:4]. The remaining bits, D[3:0] of the internal register are fixed at 0x0. Sets an alert when

the converter result is below the value in the alert low threshold register, and the alert is

disabled when it is above the value in the alert low threshold register.

0x800 R/W

Rev. 0 | Page 29 of 31

AD7389-4

Data Sheet

ALERT HIGH THRESHOLD REGISTER

15 14 13 12 11 10

9

8

7

6

5

4

3

2

1

0

1

[15:12] ADDRESSING (R/W)

[11:0] ALERT_HIGH (R/W)

Addressing

Alert High

Table 22. Bit Descriptions for Alert High Threshold Register

Bits Bit Name Description

Reset Access

[15:12] ADDRESSING Addressing. Bits[15:12] define the address of the relevant register. See the Addressing

Registers section for further details.

0x0

R/W

[11:0]

ALERT_HIGH Alert High. Bits D[11:0] from ALERT_HIGH move to the MSBs of the internal alert high

register, D[15:4]. The remaining bits, D[3:0] of the internal are fixed at 0xF. Sets an alert when

the converter result is above the value in the alert high threshold register, and the alert is

disabled when it is below the value in the alert high threshold register.

0x7FF R/W

Rev. 0 | Page 30 of 31

Data Sheet

AD7389-4

OUTLINE DIMENSIONS

4.10

4.00 SQ

3.90

0.30

0.25

0.20

PIN 1

CORNER

1

INDICATOR

19

24

18

1

0.50

BSC

0.60

0.50 SQ

0.40

0.45

0.40

0.30

13

12

6

7

TOP VIEW

SIDE VIEW

BOTTOM VIEW

0.60

0.55

0.50

FOR PROPER CONNECTION OF

THE EXPOSED PAD, REFER TO

THE PIN CONFIGURATION AND

FUNCTION DESCRIPTIONS

0.050 MAX

0.035 NOM

COPLANARITY

SEATING

PLANE

0.08

SECTION OF THIS DATA SHEET.

0.152 REF

COMPLIANT TO JEDEC STANDARDS MO-248-UGGD

Figure 43. 24-Lead Lead Frame Chip Scale Package [LFCSP]

4 mm × 4 mm Body and 0.55 mm Package Height

(CP-24-25)

Dimensions shown in millimeters

ORDERING GUIDE

Model^{1, 2, 3}

AD7389-4BCPZ

AD7389-4BCPZ-RL

AD7389-4BCPZ-RL7

EVAL-AD7380-4FMCZ

EVAL-SDP-CH1Z

Resolution

16-Bit

Temperature Range

−40°C to +125°C

Package Description

Package Option

CP-24-25

24-Lead Lead Frame Chip Scale Package [LFCSP]

AD7380-4 Evaluation Board

16-Bit

CP-24-25

Evaluation Board Controller

¹Z = RoHS Compliant Part.

²The EVAL-AD7380-4FMCZ is configurable to use with the AD7389-4.

³The EVAL-AD7380-4FMCZ is compatible with the EVAL-SDP-CH1Z high speed controller board.

registered trademarks are the property of their respective owners.

D22956-1/22(0)

Rev. 0 | Page 31 of 31


型号：	AD7386
厂家：	ADI
描述：	Differential Input, Quad, Internal Reference Simultaneous Sampling, 16-Bit SAR ADC
文件：	总31页 (文件大小：611K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

AD7386 [ADI]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB

SI9137LG

SI9122E