AD7703CN [ADI]
LC2MOS 20-Bit A/D Converter; LC2MOS 20位A / D转换器型号: | AD7703CN |
厂家: | ADI |
描述: | LC2MOS 20-Bit A/D Converter |
文件: | 总16页 (文件大小:253K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
2
LC MOS
20-Bit A/D Converter
a
AD7703
FEATURES
FUNCTIO NAL BLO CK D IAGRAM
Monolithic 20-Bit ADC
0.0003% Linearity Error
AVSS
DVSS
SC1
SC2
17
20-Bit No Missed Codes
On-Chip Self-Calibration Circuitry
Program m able Low -Pass Filter
0.1 Hz to 10 Hz Corner Frequency
0 to +2.5 V or +2.5 V Analog Input Range
4 kSPS Output Data Rate
Flexible Serial Interface
Ultralow Pow er
7
6
4
AD7703
15
14
DVDD
AVDD
CALIBRATION
MICROCONTROLLER
CALIBRATION
SRAM
13
CAL
20-BIT CHARGE BALANCE A/D
CONVERTER
AIN
9
12
11
BP/UP
SLEEP
6-POLE GAUSSIAN
ANALOG
MODULATOR
VREF
10
LOW-PASS
DIGITAL FILTER
APPLICATIONS
Industrial Process Control
Weigh Scales
Portable Instrum entation
Rem ote Data Acquisition
AGND
DGND
8
5
20 SDATA
19
CLOCK
SERIAL INTERFACE
GENERATOR
LOGIC
SCLK
3
2
1
16
18
MODE
CLKIN CLKOUT
CS
DRDY
GENERAL D ESCRIP TIO N
P RO D UCT H IGH LIGH TS
T he AD7703 is a 20-bit ADC which uses a sigma delta conver-
sion technique. T he analog input is continuously sampled by an
analog modulator whose mean output duty cycle is proportional
to the input signal. T he modulator output is processed by an
on-chip digital filter with a six-pole Gaussian response, which
updates the output data register with 20-bit binary words at
word rates up to 4 kHz. T he sampling rate, filter corner fre-
quency and output word rate are set by a master clock input
that may be supplied externally, or by an on-chip gate oscillator.
1. T he AD7703 offers 20-bit resolution coupled with
outstanding 0.0003% accuracy.
2. No missing codes ensures true, usable, 20-bit dynamic range,
removing the need for programmable gain and level-setting
circuitry.
3. T he effects of temperature drift are eliminated by on-chip
self-calibration, which removes zero and gain error. External
circuits can also be included in the calibration loop to remove
system offsets and gain errors.
T he inherent linearity of the ADC is excellent, and endpoint
accuracy is ensured by self-calibration of zero and full scale
which may be initiated at any time. T he self-calibration scheme
can also be extended to null system offset and gain errors in the
input channel.
4. A flexible synchronization allows the AD7703 to interface
directly to the serial ports of industry standard
microcontrollers and DSP processors.
5. Low operating power consumption and an ultralow power
standby mode make the AD7703 ideal for loop powered
remote sensing applications, or battery-powered portable
instruments.
T he output data is accessed through a serial port, which has two
synchronous modes suitable for interfacing to shift registers or
the serial ports of industry standard microcontrollers.
CMOS construction ensures low power dissipation, and a power
down mode reduces the idle power consumption to only 10 W.
REV. D
Inform ation furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assum ed by Analog Devices for its
use, nor for any infringem ents of patents or other rights of third parties
which m ay result from its use. No license is granted by im plication or
otherwise under any patent or patent rights of Analog Devices.
© Analog Devices, Inc., 1996
One Technology Way, P.O. Box 9106, Norw ood, MA 02062-9106, U.S.A.
Tel: 617/ 329-4700
Fax: 617/ 326-8703
(T = +25؇C; AV = DV = +5 V; AV = DV = –5 V; V = +2.5 V; fCLKIN = 4.096 MHz;
AD7703–SPECIFICATIONS
A
DD
DD
SS
SS
REF
BP/UP = +5 V; MODE = +5 V; A Source Resistance = 1 k⍀1 with 1 nF to AGND at A unless otherwise noted.)
IN
IN
P aram eter
A/S Versions2
B Version 2
C Version2
Units
Test Conditions/Com m ents
ST AT IC PERFORMANCE
Resolution
20
20
20
Bits
Integral Nonlinearity, T MIN to T MAX
+25°C
T MIN to T MAX
±0.0015
±0.003
±0.003
±0.0007
±0.0015
±0.0015
±0.5
±4
±0.0003
±0.0008
±0.0012
±0.5
±4
% FSR typ
% FSR max
% FSR max
LSB typ
Differential Nonlinearity, TMIN to TMAX ± 0.5
Guaranteed No Missing Codes
Positive Full-Scale Error3
±4
LSB typ
±16
±19/±37
±4
±16
±19
±4
±16
±19
±4
LSB max
LSB typ
LSB typ
Full-Scale Drift4
Unipolar Offset Error3
±16
±26
±67 +48/–400
±4
±16
±26
±67
±4
±16
±26
±67
±4
LSB max
LSB typ
LSB typ
Unipolar Offset Drift4
Bipolar Zero Error3
T emp Range: 0°C to +70°C
Specified T emp Range
LSB typ
±16
±13
±34 +24/–200
±8
±16
±13
±34
±8
±16
±13
±34
±8
LSB max
LSB typ
LSB typ
Bipolar Zero Drift4
T emp Range: 0°C to +70°C
Specified T emp Range
Bipolar Negative Full-Scale Errors3
LSB typ
±32
±10/±20
1.6
±32
±10
1.6
±32
±10
1.6
LSB max
LSB typ
LSB rms typ
Bipolar Negative Full-Scale Drift4
Noise (Referred to Output)
DYNAMIC PERFORMANCE
Sampling Frequency, fS
Output Update Rate, fOUT
Filter Corner Frequency, f–3 dB
Settling T ime to ±0.0007% FS
fCLKIN/256
fCLKIN/256
fCLKIN/256
Hz
Hz
Hz
sec
fCLKIN/1024
fCLKIN/409,600
507904/fCLKIN
fCLKIN/1024
fCLKIN/409,600
507904/fCLKIN
fCLKIN/1024
fCLKIN/409,600
507904/fCLKIN
For Full-Scale Input Step
SYST EM CALIBRAT ION
Positive Full-Scale Calibration Range
Positive Full-Scale Overrange
VREF + 0.1
VREF + 0.1
VREF + 0.1
VREF + 0.1
VREF + 0.1
VREF + 0.1
V max
V max
System Calibration Applies to
Unipolar and Bipolar Ranges.
Negative Full-Scale Overrange
Maximum Offset Calibration Ranges5, 6
Unipolar Input Range
–(VREF + 0.1)
–(VREF + 0.1)
–(VREF + 0.1)
–(VREF + 0.1)
–(VREF + 0.1)
–(VREF + 0.1)
V max
V max
After Calibration, if AIN > VREF
the Device Will Output All 1s.
If AIN < 0 (Unipolar) or –VREF
(Bipolar), the Device Will
Output all 0s
,
Bipolar Input Range
–0.4 VREF to +0.4 VREF –0.4 VREF to +0.4 VREF –0.4 VREF to +0.4 VREF V max
0.8 VREF
2 VREF + 0.2
Input Span7
0.8 VREF
2 VREF + 0.2
0.8 VREF
2 VREF + 0.2
V min
V max
ANALOG INPUT
Unipolar Input Range
Bipolar Input Range
Input Capacitance
Input Bias Current1
0 to +2.5
±2.5
20
0 to +2.5
±2.5
20
0 to +2.5
±2.5
20
Volts
Volts
pF typ
nA typ
1
1
1
LOGIC INPUT S
All Inputs except CLKIN
VINL, Input Low Voltage
VINH , Input High Voltage
CLKIN
0.8
2.0
0.8
2.0
0.8
2.0
V max
V min
V
INL, Input Low Voltage
0.8
3.5
10
0.8
3.5
10
0.8
3.5
10
V max
V min
µA max
VINH , Input High Voltage
IIN, Input Current
LOGIC OUT PUT S
VOL, Output Low Voltage
VOH, Output High Voltage
Floating State Leakage Current
Floating State Output Capacitance
0.4
DVDD –1
±10
9
0.4
DVDD –1
±10
9
0.4
DVDD –1
±10
9
V max
V min
µA max
pF typ
ISINK = 1.6 mA
ISOURCE = 100 µA
POWER REQUIREMENT S
Power Supply Voltages
Analog Positive Supply (AVDD
Digital Positive Supply (DVDD
Analog Negative Supply (AVSS
Digital Negative Supply (DVSS
Calibration Memory Retention
Power Supply Voltage
)
)
)
)
4.5/5.5
4.5/5.5
4.5/5.5
V min/V max For Specified Performance
V min/V max
V min/V max
4.5/AVDD
–4.5/–5.5
–4.5/–5.5
4.5/AVDD
–4.5/–5.5
–4.5/–5.5
4.5/AVDD
–4.5/–5.5
–4.5/–5.5
V min/V max
2.0
2.0
2.0
V min
–2–
REV. D
AD7703
P aram eter
A/S Versions2
B Version2
C Version2
Units
Test Conditions/Com m ents
ST AT IC PERFORMANCE
DC Power Supply Currents8
Analog Positive Supply (AIDD
Digital Positive Supply (DIDD
Analog Negative Supply (AISS
Digital Negative Supply (DISS
Power Supply Rejection9
Positive Supplies
)
)
)
)
3.2
1.5
3.2
0.1
3.2
1.5
3.2
0.1
3.2
1.5
3.2
0.1
mA max
mA max
mA max
mA max
T ypically 2 mA
T ypically 1 mA
T ypically 2 mA
T ypically 0.03 mA
70
75
70
75
70
75
dB typ
dB typ
Negative Supplies
Power Dissipation
Normal Operation
40
40
40
mW rnax
SLEEP = Logic 1,
T ypically 25 mW
SLEEP = Logic 0,
T ypically 10 µW
Standby Operations10
A, B, C
S
20
40
20
40
20
40
µW max
µW max
NOT ES
1T he AIN pin presents a very high impedance dynamic load which varies with clock frequency. A ceramic 1 nF capacitor from the A IN to AGND is necessary. Source
resistance should be 750 Ω or less.
2T emperature Ranges are as follows: A, B, C Versions: –40°C to +85°C; S Version: –55°C to +125°C.
3Applies after calibration at the temperature of interest. Full-Scale Error applies for both unipolar and bipolar input ranges.
4T otal drift over the specified temperature range after calibration at power-up at +25 °C. T his is guaranteed by design and/or characterization. Recalibration at any
temperature will remove these errors.
5In unipolar mode the offset can have a negative value (–VREF) such that the unipolar mode can mimic bipolar mode operation.
6T he specifications for input overrange and for input span apply additional constraints on the offset calibration range.
7For unipolar mode, input span is the difference between full scale and zero scale. For bipolar mode, input span is the difference between positive and negative
full-scale points. When using less than the maximum input span, the span range may be placed anywhere within the range of ±(VREF + 0.1).
8All digital outputs unloaded. All digital inputs at 5 V CMOS levels.
9Applies in 0.1 Hz to 10 Hz bandwidth. PSRR at 60 Hz will exceed 120 dB due to the digital filter.
10CLKIN is stopped. All digital inputs are grounded.
Specifications subject to change without notice.
ABSO LUTE MAXIMUM RATINGS*
(T A = +25°C unless otherwise noted)
O RD ERING GUID E
Linearity
DVDD to AGND . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +6 V
DVDD to AVDD . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +0.3 V
DVSS to AGND . . . . . . . . . . . . . . . . . . . . . . . . +0.3 V to –6 V
AVDD to AGND . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +6 V
AVSS to AGND . . . . . . . . . . . . . . . . . . . . . . . . +0.3 V to –6 V
AGND to DGND . . . . . . . . . . . . . . . . . . . . . –0.3 V to +0.3 V
Digital Input Voltage to DGND . . . . –0.3 V to DVDD + 0.3 V
Analog Input Voltage to AGND . . . . . . . . . . . AVSS – 0.3 V to
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AVDD + 0.3 V
Input Current to Any Pin Except Supplies1 . . . . . . . . ±10 mA
Operating T emperature Range
Industrial (A, B, C Versions) . . . . . . . . . . . –40°C to +85°C
Extended (S Version) . . . . . . . . . . . . . . . . –55°C to +125°C
Storage T emperature Range . . . . . . . . . . . . –65°C to +150°C
Lead T emperature (Soldering, 10 secs) . . . . . . . . . . . +300°C
Power Dissipation (DIP Package) to +75°C . . . . . . . 450 mW
Derates above +75°C by . . . . . . . . . . . . . . . . . . . . 10 mW/°C
Power Dissipation (SOIC Package) to +75°C . . . . . . 250 mW
Derates above +75°C by . . . . . . . . . . . . . . . . . . . . 15 mW/°C
Tem perature
Range
Error
(% FSR)
P ackage
O ptions*
Model
AD7703AN
AD7703BN
AD7703CN
AD7703AR
AD7703BR
AD7703CR
AD7703AQ
AD7703BQ
AD7703CQ
AD7703SQ
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–55°C to +125°C
0.003
N-20
N-20
N-20
R-20
R-20
R-20
Q-20
Q-20
Q-20
Q-20
0.0015
0.0012
0.003
0.0015
0.0012
0.003
0.0015
0.0012
0.003
*N = Plastic DIP; R = SOIC; Q = Cerdip.
NOT ES
*Stresses above those listed under “Absolute Maximum Ratings” may cause
permanent damage to the device. T his is a stress rating only and functional
operation of the device at these or any other conditions above those listed in the
operational sections of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
1T ransient currents of up to 100 mA will not cause SCR latch-up.
CAUTIO N
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although this device features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. T herefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
REV. D
–3–
AD7703
TIMING CHARACTERISTICS
(AV = DV = +5 V ؎ 10%; AV = DV = –5 V ؎ 10%; AGND = DGND = 0 V; fCLKIN
=
1, 2
DD
DD
SS
SS
4.096 MHz; Input Levels: Logic 0 = 0 V, Logic 1 = DV ; unless otherwise noted.)
DD
Lim it at TMIN, TMAX Lim it at TMIN, TMAX
P aram eter
(A, B, C Versions)
(S Version)
Units
Conditions/Com m ent6
Master Clock Frequency: Internal Gate Oscillator
3, 4
fCLKIN
200
5
200
5
kHz min
MHz max T ypically 4096 kHz
200
5
50
50
0
200
5
50
50
0
kHz min
MHz max
ns max
ns max
ns min
Master Clock Frequency: Externally Supplied
5
tr
Digital Output Rise T ime. T ypically 20 ns
Digital Output Fall T ime. T ypically 20 ns
SC1, SC2 to CAL High Setup T ime
tf5
t1
t26
50
1000
50
1000
ns min
ns min
SC1, SC2 Hold T ime After CAL Goes High
SLEEP High to CLKIN High Setup T ime
t3
SSC MODE
7
t4
3/fCLKIN
100
250
300
790
3/fCLKIN
100
250
300
790
ns max
ns max
ns min
ns max
ns max
ns max
ns max
Data Access T ime (CS Low to Data Valid)
SCLK Falling Edge to Data Valid Delay (25 ns typ)
MSB Data Setup T ime. T ypically 380 ns
SCLK High Pulse Width. T ypically 240 ns
SCLK Low Pulse Width. T ypically 730 ns
SCLK Rising Edge to Hi-Z Delay (1/fCLKIN + 100 ns typ)
CS High to Hi-Z Delay
t5
t6
t7
t8
t9
l/fCLKIN + 200
4/fCLKIN + 200
l/fCLKIN + 200
4/fCLKIN + 200
8, 9
t10
SEC MODE
fSCLK
t11
5
35
5
35
MHz max Serial Clock Input Frequency
ns min
ns min
ns max
ns max
ns max
ns max
SCLK High Pulse Width
SCLK Low Pulse Width
Data Access Time (CS Low to Data Valid). Typically 80 ns
SCLK Falling Edge to Data Valid Delay. Typically 75 ns
CS High to Hi-Z Delay
t12
t13
t14
t15
160
160
150
250
200
160
160
150
250
200
7, 10
11
8
8
t16
SCLK Falling Edge to Hi-Z Delay. T ypically 100 ns
NOT ES
1Sample tested at +25°C to ensure compliance. All input signals are specified with tr = tf = 5 ns (10% to 90% of 5 V) and timed from a voltage level of 1.6 V.
2See Figures 1 to 6.
3CLKIN duty cycle range is 20% to 80%. CLKIN must be supplied whenever the AD7703 is not in SLEEP mode. If no clock is present in this case, the device can
draw higher current than specified and possibly become uncalibrated.
4T he AD7703 is production tested with fCLKIN at 4.096 MHz. It is guaranteed by characterization to operate at 200 kHz.
5Specified using 10% and 90% points on waveform of interest.
6In order to synchronize several AD7703s together using the SLEEP pin, this specification must be met.
7t4 and t13 are measured with the load circuit of Figure 1 and defined as the time required for an output to cross 0.8 V or 2.4 V.
8t9, t10, t15 and t16 are derived from the measured time taken by the data outputs to change 0.5 V when loaded with the circuit of Figure 1. T he measured number is
then extrapolated back to remove the effects of charging or discharging the 100 pF capacitor. T his means that the tune quoted in the T iming Characteristics is the
true bus relinquish time of the part and as such is independent of external bus loading capacitances.
9If CS is returned high before all 20 bits are output, the SDAT A and SCLK outputs will complete the current data bit and then go to high impedance.
10If CS is activated asynchronously to DRDY, CS will not be recognized if it occurs when DRDY is high for four clock cycles. T he propagation delay time may be as
great as 4 CLKIN cycles plus 160 ns. T o guarantee proper clocking of SDAT A when using asynchronous CS, the SCLK input should not be taken high sooner than
4 CLKIN cycles plus 160 ns after CS goes low.
11SDAT A is clocked out on the falling edge of the SCLK input.
CAL
I
OL
1.6mA
t2
SC1,SC2 VALID
t1
TO
OUTPUT
PIN
SC1, SC2
+2.1V
C
L
100pF
Figure 2. Calibration Control Tim ing
I
OH
200µA
CLKIN
t3
Figure 1. Load Circuit for Access Tim e and Bus Relinquish
Tim e
SLEEP
Figure 3. Sleep Mode Tim ing
–4–
REV. D
AD7703
CS
CS
t15
t10
HI-Z
HI-Z
DATA
VALID
DATA
VALID
SDATA
SDATA
Figure 4. SSC Mode Data Hold Tim e
Figure 5a. SEC Mode Data Hold Tim e
CLKIN
CS
DRDY
CS
t7
t12
t8
t11
HI-Z
HI-Z
HI-Z
SCLK
SCLK
t9
t4
t13
t8
t16
DB0
t14
DB18
t5
HI-Z
HI-Z
DB19
SDATA
DB1
HI-Z
DB19
SDATA
DB18
DB1
DB0
Figure 6. SSC Mode Tim ing Diagram
Figure 5b. SEC Mode Tim ing Diagram
P O SITIVE FULL-SCALE O VERRANGE
TERMINO LO GY
LINEARITY ERRO R
Positive full-scale overrange is the amount of overhead available
to handle input voltages greater than +VREF (for example, noise
peaks or excess voltages due to system gain errors in system cali-
bration routines) without introducing errors due to overloading
the analog modulator or overflowing the digital filter.
T his is the maximum deviation of any code from a straight line
passing through the endpoints of the transfer function. T he end-
points of the transfer function are zero-scale (not to be confused
with bipolar zero), a point 0.5 LSB below the first code transi-
tion (000 . . . 000 to 000 . . . 001) and full scale, a point 1.5 LSB
above the last code transition (111 . . . 110 to 111 . . . 111).
T he error is expressed as a percentage of full scale.
NEGATIVE FULL-SCALE O VERRANGE
T his is the amount of overhead available to handle voltages be-
low –VREF without overloading the analog modulator or over-
flowing the digital filter. Note that the analog input will accept
negative voltage peaks even in the unipolar mode.
D IFFERENTIAL LINEARITY ERRO R
T his is the difference between any code’s actual width and the
ideal (1 LSB) width. Differential linearity error is expressed in
LSBs. A differential linearity specification of ±1 LSB or less
guarantees monotonicity.
O FFSET CALIBRATIO N RANGE
In the system calibration modes (SC2 Low) the AD7703 cali-
brates its offset with respect to the AIN pin. T he offset calibra-
tion range specification defines the range of voltages that the
AD7701 can accept and still calibrate offset accurately.
P O SITIVE FULL-SCALE ERRO R
Positive full-scale error is the deviation of the last code transition
(111 . . . 110 to 111 . . . 111) from the ideal (VREF –3/2 LSBs).
It applies to both positive and negative analog input ranges.
FULL-SCALE CALIBRATIO N RANGE
T his is the range of voltages that the AD7703 can accept in the
system calibration mode and still calibrate full scale correctly.
UNIP O LAR O FFSET ERRO R
Unipolar offset error is the deviation of the first code transition
from the ideal (AGND + 0.5 LSB) when operating in the uni-
polar mode.
INP UT SP AN
In system calibration schemes, two voltages applied in sequence
to the AD7703’s analog input define the analog input range.
T he input span specification defines the minimum and maxi-
mum input voltages from zero to full scale that the AD7703 can
accept and still calibrate gain accurately.
BIP O LAR ZERO ERRO R
T his is the deviation of the midscale transition (0111 . . . 111 to
1000 . . . 000) from the ideal (AGND – 0.5 LSB) when operat-
ing in the bipolar mode.
BIP O LAR NEGATIVE FULL-SCALE ERRO R
T his is the deviation of the first code transition from the ideal
(–VREF + 0.5 LSB), when operating in the bipolar mode.
REV. D
–5–
AD7703
P IN FUNCTIO N D ESCRIP TIO N
P in
Mnem onic D escription
1
MODE
Selects the Serial Interface Mode. If MODE is tied to DGND, the Synchronous External Clocking (SEC)
mode is selected. SCLK is configured as an input, and the output appears without formatting, the MSB com-
ing first. If MODE is tied to +5 V, the AD7703 operates in the Synchronous Self-Clocking (SSC) mode.
SCLK is configured as an output, with a clock frequency for fCLKIN/4 and 25% duty cycle.
2
CLKOUT
Clock Output to generate an Internal Master Clock by connecting a crystal between CLKOUT and CLKIN.
If an external clock is used, CLKOUT is not connected.
3
CLKIN
Clock Input for External Clock.
4, 17
SC1, SC2
System Calibration Pins. T he state of these pins, when CAL is taken high, determines the type of calibration
performed.
5
DGND
DVSS
AVSS
AGND
AIN
Digital Ground. Ground reference for all digital signals.
Digital Negative Supply, –5 V nominal.
Analog Negative Supply, –5 V nominal.
Analog Ground. Ground reference for all analog signals.
Analog Input.
6
7
8
9
10
VREF
Voltage Reference Input, +2.5 V nominal. T his determines the value of positive full-scale in the unipolar
mode and of both positive and negative full-scale in the Bipolar Mode.
11
12
13
SLEEP
BP/UP
CAL
Sleep mode pin. When this pin is taken low, the AD7703 goes into a low-power mode with typically 10 µW
power consumption.
Bipolar/Unipolar mode pin. When this pin is Low, the AD7703 is configured for a unipolar input range going
from AGND to VREF. When Pin 12 is High, the AD7703 is configured for a bipolar input range, ±VREF
.
Calibration mode pin. When CAL is taken High for more than 4 cycles, the AD7703 is reset and performs a
calibration cycle when CAL is brought Low again. T he CAL pin can also be used as a strobe to synchronize
the operation of several AD7703s.
14
15
16
AVDD
DVDD
CS
Analog Positive Supply, +5 V nominal.
Digital Positive Supply, +5 V nominal.
Chip Select Input. When CS is brought low, the AD7703 will begin to transmit serial data in a format deter-
mined by the state of the MODE pin.
18
DRDY
Data Ready Output. DRDY is low when valid data is available in the output register. It goes high after trans-
mission of a word is completed. It also goes high for four clock cycles when a new data word is being loaded
into the output register, to indicate that valid data is not available, irrespective of whether data transmission is
complete or not.
19
20
SCLK
Serial Clock Input/Output. T he SCLK pin in configured as an input or output, dependent on the type of se-
rial data transmission that has been selected by the MODE pin. When configured as an output in the Syn-
chronous Self-Clocking mode, it has a frequency of fCLKIN/4 and a duty cycle of 25%.
SDAT A
Serial Data Output. T he AD7703’s output data is available at this pin as a 20-bit serial word.
Table I. Bit Weight Table (2.5 V Reference Voltage)
P IN CO NFIGURATIO N
D IP , Cer dip, SO IC
UNIP O LAR MO D E
LSBs % FS ppm FS LSBs % FS
BIP O LAR MO D E
ppm FS
V
20
1
2
MODE
SDATA
19 SCLK
CLKOUT
0.596
1.192
2.384
4.768
9.537
0.25
0.5
1.00
2.00
4.00
0.0000238 0.24
0.13
0.26
0.5
1.00
2.00
0.0000119
0.0000238
0.0000477
0.0000954
0.0001907
0.12
0.24
0.48
0.95
1.91
3
18
17
16
15
DRDY
SC2
CLKIN
SC1
0.0000477 0.48
0.0000954 0.95
0.0001907 1.91
0.0003814 3.81
4
AD7703
TOP VIEW
5
CS
DGND
DVSS
AVSS
6
DVDD
(Not to Scale)
14 AVDD
7
13
8
CAL
AGND
AIN
12
9
BP/UP
11
VREF
10
SLEEP
–6–
REV. D
AD7703
GENERAL D ESCRIP TIO N
TH EO RY O F O P ERATIO N
T he AD7703 is a 20-bit A/D converter with on-chip digital
filtering, intended for the measurement of wide dynamic range,
low frequency signals such as those representing chemical,
physical or biological processes. It contains a charge-balancing
(sigma-delta) ADC, calibration microcontroller with on-chip
static RAM, a clock oscillator and a serial communications port.
T he general block diagram of a sigma-delta ADC is shown in
Figure 8. It contains the following elements:
1. A sample-hold amplifier
2. A differential amplifier or subtracter
3. An analog low-pass filter
4. A 1-bit A/D converter (comparator)
5. A 1-bit DAC
T he analog input signal to the AD7703 is continuously sampled
at a rate determined by the frequency of the master clock,
CLKIN. A charge-balancing A/D converter (sigma-delta modu-
lator) converts the sampled signal into a digital pulse train
whose duty cycle contains the digital information. A six-pole
Gaussian digital low-pass filter processes the output of the
sigma-delta modulator and updates the 20-bit output register at
a 4 kHz rate. T he output data can be read from the serial port
randomly or periodically at any rate up to 4 kHz.
6. A digital low-pass filter
S/H AMP
COMPARATOR
ANALOG
LOW-PASS
DIGITAL
FILTER
FILTER
DIGITAL DATA
DAC
+5V
ANALOG
SUPPLY
AV
DV
DD
DD
0.1µF
0.1µF
10µF
SLEEP
MODE
Figure 8. General Sigm a-Delta ADC
DATA
DRDY
CS
2.5V
READY
VOLTAGE
REFERENCE
V
REF
READ
(TRANSMIT)
In operation, the sampled analog signal is fed to the subtracter,
along with the output of the 1-bit DAC. T he filtered difference
signal is fed to the comparator, whose output samples the
difference signal at a frequency many times that of the analog
signal frequency (oversampling).
AD7703
SERIAL
CLOCK
SCLK
RANGE
SELECT
BP/UP
CAL
SERIAL
DATA
SDATA
CALIBRATE
CLKIN
ANALOG
INPUT
A
CLKOUT
IN
Oversampling is fundamental to the operation of sigma-delta
ADCs. Using the quantization noise formula for an ADC:
SC1
SC2
ANALOG
GROUND
AGND
DGND
0.1µF
SNR =(6.02 × number of bits +1.76) dB,
0.1µF
AV
SS
DV
SS
–5V
ANALOG
SUPPLY
a 1-bit ADC or comparator yields an SNR of 7.78 dB.
10µF
T he AD7703 samples the input signal at 16 kHz, which spreads
the quantization noise from 0 kHz to 8 kHz. Since the specified
analog input bandwidth of the AD7703 is only 0 Hz to 10 Hz,
the noise energy in this bandwidth would be only 1/800 of the
total quantization noise, assuming that the noise energy was
spread evenly throughout the spectrum. It is reduced still
further by analog filtering in the modulator loop, which shapes
the quantization noise spectrum to move most of the noise
energy to frequencies above 10 Hz. T he SNR performance in
the 0 Hz to 10 Hz range is conditioned to the 20-bit level in this
fashion.
Figure 7. Typical System Connection Diagram
T he AD7703 can perform self-calibration using the on-chip
calibration microcontroller and SRAM to store calibration
parameters. A calibration cycle may be initiated at any time
using the CAL control input.
Other system components may also be included in the
calibration loop to remove offset and gain errors in the input
channel.
For battery operation, the AD7703 also offers a standby mode
that reduces idle power consumption to typically 10 µW.
T he output of the comparator provides the digital input for the
1-bit DAC, so the system functions as a negative feedback loop
which minimizes the difference signal. T he digital data that
represents the analog input voltage is in the duty cycle of the
pulse train appearing at the output of the comparator. It can be
retrieved as a parallel binary data word using a digital filter.
Sigma-delta ADCs are generally described by the order of the
analog low-pass filter. A simple example of a first order sigma-
delta ADC is shown in Figure 8. T his contains only a first-order
low-pass filter or integrator.
T he AD7703 uses a second-order sigma-delta modulator and a
digital filter that provides a rolling average of the sampled
output. After power-up or if there is a step change in the input
voltage, there is a settling time before valid data is obtained.
REV. D
–7–
AD7703
D IGITAL FILTERING
T he AD7703’s digital filter behaves like an analog filter, with a
few minor differences.
T he output settling of the AD7703 in response to a step input
change is shown in Figure 10. T he Gaussian response has fast
settling with no overshoot, and the worst-case settling time to
±0.0007% is 125 ms with a 4.096 MHz master clock frequency.
First, since digital filtering occurs after the A to D conversion
process, it can remove noise injected during the conversion
process. Analog filtering cannot do this.
On the other hand, analog filtering can remove noise superim-
posed on the analog signal before it reaches the ADC. Digital
filtering cannot do this and noise peaks riding on signals near
full scale have the potential to saturate the analog modulator
and digital filter, even though the average value of the signal is
within limits. T o alleviate this problem, the AD7703 has over-
range headroom built into the sigma-delta modulator and digital
filter which allows overrange excursions of 100 mV. If noise sig-
nals are larger than this, consideration should be given to analog
input filtering, or to reducing the gain in the input channel so
that a full-scale input (2.5 V) gives only a half-scale input to the
AD7703 (1.25 V). T his will provide an overrange capability
greater than 100% at the expense of reducing the dynamic range
by 1 bit (50%).
100
80
60
40
20
0
0
40
80
120
160
TIME – ms
Figure 10. AD7703 Step Response
FILTER CH ARACTERISTICS
T he cutoff frequency of the digital filter is fCLK/409600. At the
maximum clock frequency of 4.096 MHz, the cutoff frequency
of the filter is 10 Hz and the data update rate is 4 kHz.
USING TH E AD 7703
SYSTEM D ESIGN CO NSID ERATIO NS
T he AD7703 operates differently from successive approxima-
tion ADCs or integrating ADCs. Since it samples the signal con-
tinuously, like a tracking ADC, there is no need for a start convert
command. T he 20-bit output register is updated at a 4 kHz rate,
and the output can be read at any time, either synchronously or
asynchronously.
Figure 9 shows the filter frequency response. T his is a 6-pole
Gaussian response that provides 55 dB of 60 Hz rejection for a
10 Hz cutoff frequency. If the clock frequency is halved to give a
5 Hz cutoff, 60 Hz rejection is better than 90 dB.
20
CLO CKING
0
f
= 4MHz
CLK
T he AD7703 requires a master clock input, which may be an
external T T L/CMOS compatible clock signal applied to the
CLKIN pin (CLKOUT not used). Alternatively, a crystal of the
correct frequency can be connected between CLKIN and
CLKOUT , when the clock circuit will function as a crystal
controlled oscillator.
–20
–40
–60
f
= 2MHz
CLK
–80
–100
–120
Figure 11 shows a simple model of the on-chip gate oscillator
and T able II gives some typical capacitor values to be used with
various resonators.
f
= 1MHz
CLK
–140
–160
R1
5MΩ
1
100
10
FREQUENCY – Hz
2
Figure 9. Frequency Response of AD7703 Filter
C2*
10pF
X1
gm = 1500µMHO
Since the AD7703 contains this low-pass filtering, there is a set-
tling time associated with step function inputs, and data will be
invalid after a step change until the settling time has elapsed.
T he AD7703 is, therefore, unsuitable for high speed multiplex-
ing, where channels are switched and converted sequentially at
high rates, as switching between channels can cause a step
change in the input. However, slow multiplexing of the AD7703
is possible, provided that the settling time is allowed to elapse
before data for the new channel is accessed.
3
C1*
10pF
AD7703
*SEE TABLE II
Figure 11. On-Chip Gate Oscillator
–8–
REV. D
AD7703
Table II. Resonator Loading Capacitors
low capacitance/voltage coefficient. T he device also achieves low
input drift through the use of chopper-stabilized techniques in
its input stage. T o ensure excellent performance over time and
temperature, the AD7703 uses digital calibration techniques
which minimize offset and gain error to typically ±4 LSBs.
Resonators
C1
C2
Ceramic
200 kHz
455 kHz
1.0 MHz
2.0 MHz
Crystals
330 pF
100 pF
50 pF
470 pF
100 pF
50 pF
AUTO CALIBRATIO N
T he AD7703 offers both self-calibration and system-calibration
facilities. For calibration to occur, the on-chip microcontroller
must record the modulator output for two different input condi-
tions. T hese are the “zero scale” and “full scale” points. In uni-
polar self-calibration mode, the zero scale point is VAGND and
the full-scale point is VREF. With these readings the microcon-
troller can calculate the gain slope for the input to output trans-
fer function of the converter. In unipolar mode the slope factor
is determined by dividing the span between zero and full scale
by 220. In bipolar mode it is determined by dividing the span by
219 since the inputs applied represent only half the total codes.
In both unipolar and bipolar modes the slope factor is saved and
used to calculate the binary output code when an analog input is
applied to the device. T able IV gives the output code size after
calibration.
20 pF
20 pF
2.000 MHz
3.579 MHz
4.096 MHz
30 pF
20 pF
None
30 pF
20 pF
None
T he input sampling frequency, output data rate, filter character-
istics and calibration time are all directly related to the master
clock frequency fCLKIN by the ratios given in the specification
table under Dynamic Performance. T herefore, the first step in
system design with the AD7703 is to select a master clock fre-
quency suitable for the bandwidth and output data rate required
by the application.
ANALO G INP UT RANGES
System calibration allows the AD7703 to compensate for system
gain and offset errors. A typical circuit where this might be used
is shown in Figure 12.
T he AD7703 performs conversion relative to an externally sup-
plied reference voltage, which allows easy interfacing to ratio-
metric systems. In addition, either unipolar or bipolar input
voltage ranges may be selected using the BP/UP input. With
BP/UP tied low, the input range is unipolar and the span is
(VREF–VAGND), where VAGND is the voltage at the device AGND
pin. With BP/UP tied high, the input range is bipolar and the
span is 2 VREF. In the bipolar mode both positive and negative
full scale are directly determined by VREF. T his offers superior
tracking of positive and negative full scale and better midscale
(bipolar zero) stability than bipolar schemes that simply scale
and offset the input range.
System calibration performs the same slope factor calculations
as self-calibration but uses voltage values presented by the
system to the AIN pin for the zero and full-scale points. T here
are two system calibration modes.
T he first mode offers system level calibration for system offset
and system gain. T his is a two step operation. T he zero-scale
point must be presented to the converter first. It must be
applied to the converter before the calibration step is initiated
and remain stable until the step is complete. T he DRDY output
from the device will signal when the step is complete by going
low. After the zero-scale point is calibrated the full-scale point is
applied and the second calibration step is initiated. Again the
voltage must remain stable throughout the calibration step.
T he digital output coding for the unipolar range is unipolar
binary and for the bipolar range it is offset binary. Bit weights
for the unipolar and bipolar modes are shown in T able I.
ACCURACY
T he two step calibration mode offers another feature. After the
sequence has been completed, additional offset calibrations can
be performed by themselves to adjust the zero reference point to
a new system zero reference value. T his second system
Sigma-delta ADCs, like VFCs and other integrating ADCs, do
not contain any source of nonmonotonicity and inherently offer
no missing codes performance.
calibration mode uses an input voltage for the zero-scale
calibration point but uses the VREF value for the full-scale point.
T he AD7703 achieves excellent linearity by the use of high
quality, on-chip silicon dioxide capacitors, which have a very
SCLK
SYSTEM
REF HI
SDATA
SIGNAL
CONDITIONING
ANALOG
MUX
CAL
SC1
A
A
IN
IN
MICRO
COMPUTER
SYSTEM
REF LO
SC2
A0
A1
AD7703
Figure 12. Typical Connections for System Calibration
REV. D
–9–
AD7703
Initiating Calibr ation
When self-calibration is completed, DRDY falls and the output
port is updated with a data word that represents the analog
input signal. When a system calibration step is completed,
DRDY will fall and the output port will be updated with the
appropriate data value (all 0s for the zero-scale point and all 1s
for the full-scale point). In the system calibration mode, the
digital filter must settle before the output code will represent the
value of the analog input signal. T ables IV and V indicate the
output code size and output coding of the AD7703 in its
various modes. In these tables, SOFF is the measured system
offset in volts and SGAIN is the measured system gain at the
full-scale point in volts.
T able III illustrates the calibration modes available in the
AD7703. Not shown in the table is the function of the BP/UP
pin which determines whether the converter has been calibrated
to measure bipolar or unipolar signals. A calibration step is
initiated by bringing the CAL pin high for at least 4 CLKIN
cycles and then bringing it low again. T he states of SC1 and
SC2 along with the BP/UP pin will determine the type of
calibration to be performed. All three signals should be stable
before the CAL pin is taken positive. T he SC1 and SC2 inputs
are latched when CAL goes high. T he BP/UP input is not
latched and therefore must remain in a fixed state throughout
the calibration and measurement cycles. Any time the state of
the BP/UP is changed, a new calibration cycle must be
performed to enable the AD7703 to function properly in the
new mode.
Span and O ffset Lim its
Whenever a system calibration mode is used, there are limits on
the amount of offset and span which can be accommodated.
T he range of input span in both the unipolar and bipolar modes
has a minimum value of 0.8 VREF and a maximum value of
2 (VREF + 0.1 V).
When a calibration step is initiated, the DRDY signal will go
high and remain high until the step is finished. T able III shows
the number of clock cycles each calibration requires. Once a
calibration step is initiated it must finish before a new calibra-
tion step can be executed. In the two step system calibration
mode, the offset calibration step must be initiated before initiat-
ing the gain calibration step.
T he amount of offset which can be accommodated depends on
whether the unipolar or bipolar mode is being used. In unipolar
mode, the system calibration modes can handle a maximum
offset of 0.2 VREF and a minimum offset of –(VREF + 0.1 V).
T hus the AD7703 in the unipolar mode can be calibrated to
mimic bipolar operation.
Table III. Calibration Truth Table
ZERO -SCALE CAL FULL-SCALE CAL SEQUENCE
CAL
SC1
SC2
CAL TYP E
CALIBRATIO N TIME
0
1
0
1
0
1
1
0
Self-Cal
VAGND
AIN
_
VREF
_
AIN
VREF
One Step
1st Step
2nd Step
One Step
3,145,655 Clock Cycles
1,052,599 Clock Cycles
1,068,813 Clock Cycles
2,117,389 Clock Cycles
System Offset
System Gain
System Offset
AIN
NOT E
DRDY remains high throughout the calibration sequence. In the Self-Cal mode, DRDY falls once the AD7703 has settled to the analog input. In all other modes
DRDY falls as the device begins to settle.
Table IV. O utput Code Size After Calibration
1 LSB
CAL MO D E
ZERO -SCALE
GAIN FACTO R
UNIP O LAR
BIP O LAR
(VREF –VAGND
)
2(VREF –VAGND )
Self-Cal
VAGND
VREF
1048576
1048576
(SGAIN –SOFF
)
2(SGAIN –SOFF )
System Cal
SOFF
SGAIN
1048576
1048576
–10–
REV. D
AD7703
Table V. AD 7703 O utput Coding
I
NP UT VO LTAGE, UNIP O LAR MO D E INP UT VO LTAGE, BIP O LAR MO D E
System Cal
Self Cal
O utput Codes
Self-Cal
System Cal
>(SGAIN –1.5 LSB)
>(VREF – 1.5 LSB)
FFFFF
>(VREF –1.5 LSB)
>(SGAIN – 1.5 LSB)
FFFFF
FFFFE
SGAIN – 1.5 LSB
VREF – 1.5 LSB
VREF – 1.5 LSB
SGAIN – 1.5 LSB
80000
(SGAIN – SOFF)/2 – 0.5 LSB
(VREF – VAGND)/2 – 0.5 LSB
VAGND – 0.5 LSB
SOFF – 0.5 LSB
7FFFF
00001
00000
SOFF + 0.5 LSB
VAGND + 0.5 LSB
–VREF + 0.5 LSB
–SGAIN + 2 SOFF + 0.5 LSB
<(–SGAIN +2 SOFF + 0.5 LSB)
<(SOFF + 0.5 LSB)
<(VAGND + 0.5 LSB)
00000
<(–VREF + 0.5 LSB)
In the bipolar mode the system offset calibration range is
restricted to ±0.4 VREF. It should be noted that the span
restrictions limit the amount of offset which can be calibrated.
T he span range of the converter in bipolar mode is equidistant
around the voltage used for the zero scale point. When the zero-
scale point is calibrated it must not cause either of the two
endpoints of the bipolar transfer function to exceed the positive
or the negative input overrange points (+VREF + 0.1) V or
updated at a rate determined by the master clock, therefore the
amount of offset drift which occurs will be proportional to the
elapsed time between samples. T hus, to minimize offset drift at
higher temperatures, higher CLKIN rates are recommended.
Gain drift within the converter depends mainly upon the tem-
perature tracking of the internal capacitors. It is not affected by
leakage currents so that it is significantly less than offset drift.
T he typical gain drift of the AD7703 is less than 40 LSBs over
the specified temperature range.
–VREF + 0.1) V. If the span range is set to a minimum (0.8 VREF
)
the offset voltage can move +0.4 VREF without causing the end
points of the transfer function to exceed the overrange points.
Alternatively, if the span range is set to 2 VREF, the input offset
cannot move more than +0.1 V or –0.1 V before an endpoint of
the transfer function exceeds the input overrange limit.
Measurement errors due to offset drift or gain drift can be elimi-
nated at any time by recalibrating the converter. Using the sys-
tem calibration mode can also minimize offset and gain errors in
the signal conditioning circuitry. Integral and differential linear-
ity are not significantly affected by temperature changes.
P O WER-UP AND CALIBRATIO N
160
A calibration cycle must be carried out after power-up to
initialize the device to a consistent starting condition and correct
calibration. T he CAL pin must be held high for at least four
clock cycles, after which calibration is initiated on the falling
edge of CAL and takes a maximum of 3,145,655 clock cycles
(approximately 768 ms with a 4.096 MHz clock). See T able III.
CLKIN = 4.096MHz
80
0
–80
T he type of calibration cycle initiated by CAL is determined by
the SC1 and SC2 inputs, in accordance with T able III.
–160
–240
–320
D r ift Consider ations
T he AD7703 uses chopper stabilization techniques to minimize
input offset drift. Charge injection in the analog switches and
leakage currents at the sampling node are the primary sources of
offset voltage drift in the converter. Figure 13 indicates the typi-
cal offset due to temperature changes after calibration at 25°C.
Drift is relatively flat up to 75°C. Above this temperature, leak-
age current becomes the main source of offset drift. Since leak-
age current doubles approximately every 10°C, the offset drifts
accordingly. T he value of the voltage on the sample capacitor is
–55
–35
–15
5
25
45
65
85
105
125
TEMPERATURE – °C
Figure 13. Typical Bipolar Offset vs. Tem perature after
Calibration at +25°C
REV. D
–11–
AD7703
INP UT SIGNAL CO ND ITIO NING
An RC filter may be added in front of the AD7703 to reduce
high frequency noise. With an external capacitor added from
AIN to AGND, the following equation will specify the maximum
allowable source resistance:
Reference voltages from +1 V to +3 V may be used with the
AD7703, with little degradation in performance. Input ranges
that cannot be accommodated by this range of reference voltages
may be achieved by input signal conditioning. T his may take the
form of gain to accommodate a smaller signal range, or passive
attenuation to reduce a larger input voltage range.
62
RS(MAX )
=
CIN
(CIN + CEXT
VE
100 mV •
Sour ce Resistance
)
fCLKIN •(CIN + CEXT ) •ln
If passive attenuators are used in front of the AD7703, care
must be taken to ensure that the source impedance is suffi-
ciently low. T he dc input resistance for the AD7703 is over
1 GΩ. In parallel with this there as a small dynamic load which
varies with the clock frequency (see Figure 14). Each time the
T he practical limit to the maximum value of source resistance is
thermal (Johnson) noise. A practical resistor may be modeled as
an ideal (noiseless) resistor in series with a noise voltage source
or in parallel with a noise current source.
R1
A
AD7703
IN
V
IN
Vn = 4 kTRf Volts
1GΩ
R2
C
EXT
in = 4 kTf /R Amperes
C
10pF
IN
where k is Boltzmann’s constant (1.38 ϫ 10–23 J/K), and T is
temperature in degrees Kelvin (°C + 273).
V
≤ 100mV
OS
AGND
Active signal conditioning circuits such as op amps generally do
not suffer from problems of high source impedance. T heir open
loop output resistance is normally only tens of ohms and, in any
case, most modern general purpose op amps have sufficiently
fast closed loop settling time for this not to be a problem. Offset
voltage in op amps can be eliminated in a system calibration
routine.
Figure 14. Equivalent Input Circuit and Input Attenuator
analog input is sampled, a 10 pF capacitor draws a charge
packet of maximum 1 pC (10 pF ϫ 100 mV) from the analog
source with a frequency fCLKIN/256. For a 4.096 MHz CLKIN,
this yields an average current draw of 16 nA. After each sample
the AD7703 allows 62 clock periods for the input voltage to
settle. T he equation which defines settling time is:
Antialias Consider ations
T he digital filter of the AD7703 does not provide any rejection
at integer multiples of the sampling frequency (nfCLKIN/256,
where n = 1, 2, 3 . . . ).
VO =VIN [1– e–t / RC
]
where VO, is the final settled value, VIN, is the value of the input
signal, R is the value of the input source resistance, C is the
With a 4.096 MHz master clock there are narrow (±10 Hz)
bands at 16 kHz, 32 kHz, 48 kHz, etc., where noise passes
unattenuated to the output.
10 pF sample capacitor. T he value of t is equal to 62/fCLKIN
.
T he following equation can be developed which gives the max-
imum allowable source resistance, RS(MAX) for an error of VE.
However, due to the AD7703’s high oversampling ratio of 800
(16 kHz to 20 Hz) these bands occupy only a small fraction of
the spectrum, and most broadband noise is filtered.
62
RS(MAX )
=
T he reduction in broadband noise is given by:
fCLKIN •(10 pF )•ln (100 mV /VE )
Provided the source resistance is less than this value, the analog
input will settle within the desired error band in the requisite 62
clock periods. Insufficient settling leads to offset errors. T hese
can be calibrated in system calibration schemes.
eout = e 2 fC /f S = 0.035 e
in
in
where ein and eout are rms noise terms referred to the input and fC
is the filter –3 dB corner frequency (fCLKIN/409600) and fS is the
sampling frequency (fCLKIN/256).
If a limit of 600 nV (0.25 LSB at 20 bits) is set for the maxi-
mum offset voltage, then the maximum allowable source resis-
tance is 125 kΩ from the above equation, assuming that there is
no external stray capacitance.
Since the ratio of fS to fCLKIN is fixed, the digital filter reduces
broadband white noise by 96.5% independent of the master
clock frequency.
–12–
REV. D
AD7703
T herefore, the two analog supplies should be individually
decoupled to AGND using 100 nF ceramic capacitors to
provide power supply noise rejection at these frequencies. T he
two digital supplies should similarly be decoupled to DGND.
VO LTAGE REFERENCE CO NNECTIO NS
T he voltage applied to the VREF pin defines the analog input
range. T he specified reference voltage is 2.5 V, but the AD7703
will operate with reference voltages from 1 V to 3 V with little
degradation in performance.
T he positive digital supply (DVDD) must never exceed the
positive analog supply (AVDD) by more than 0.3 V. Power
supply sequencing is therefore important. If separate analog and
digital supplies are used, care must be taken to ensure that the
analog supply is powered up first.
T he reference input presents exactly the same dynamic load as
the analog input, but in the case of the reference input, source
resistance and long settling time introduce gain errors rather
than offset errors. Fortunately, most precision references have
sufficiently low output impedance and wide enough bandwidth
to settle to the required accuracy within 62 clock cycles.
It is also important that power is applied to the AD7703 before
signals at VREF, AIN or the logic input pins in order to avoid any
possibility of latch-up. If separate supplies are used for the
AD7703 and the system digital circuitry, then the AD7703
should be powered up first.
T he digital filter of the AD7703 removes noise from the refer-
ence input, just as it does with noise at the analog input, and
the same limitations apply regarding lack of noise rejection at
integer multiples of the sampling frequency. Note that the refer-
ence should be chosen to minimize noise below 10 Hz. T he
AD7703 typically exhibits 1.6 LSB rms noise in its measure-
ments. T his specification assumes a clean reference. Many
monolithic bandgap references are available which can supply
the 2.5 V needed for the AD7703. However, some of these are
not specified for noise especially in the 0.1 Hz to 10 Hz band-
width. If the reference noise in this bandwidth is excessive, it
can degrade the performance of the AD7703. Recommended
references are the AD580 and the LT 1019. Both of these 2.5 V
references typically have less than 10 V p-p noise in the 0.1 Hz
to 10 Hz band.
A typical scheme for powering the AD7703 from a single set of
±5 V rails is shown Figure 7. In this circuit AVDD and DVDD are
brought along separate tracks from the same +5 V supply.
T hus, there is no possibility of the digital supply coming up
before the analog supply.
SLEEP MO D E
T he low power standby mode is initiated by taking the SLEEP
input low, which shuts down all analog and digital circuits and
reduces power consumption to 10 µW. When coming out of
SLEEP mode it is sometimes possible (when using a crystal to
generate CLKIN, for example) to lose the calibration coeffi-
cients. T herefore, it is advisable as a safeguard to always do a
calibration cycle after coming out of SLEEP mode.
P O WER SUP P LIES AND GRO UND ING
AGND is the ground reference voltage for the AD7703, and is
completely independent of DGND. Any noise riding on the
AGND input with respect to the system analog ground will
cause conversion errors. AGND should therefore be used as the
system ground and also as the ground for the analog input and
the reference voltage.
D IGITAL INTERFACE
T he AD7703’s serial communications port allows easy
interfacing to industry standard microprocessors. T wo different
modes of operation are available, optimized for different types
of interface.
T he analog and digital power supplies to the AD7703 are
independent and separately pinned out, to minimize coupling
between analog and digital sections of the device. T he digital
filter will provide rejection of broadband noise on the power
supplies, except at integer multiples of the sampling frequency.
REV. D
–13–
AD7703
SYNCH RO NO US SELF-CLO CKING MO D E (SSC)
T he SSC mode (MODE pin high) allows easy interfacing to
serial-parallel conversion circuits in systems with parallel data
communication. T his mode allows interfacing to 74XX299
Universal Shift registers without any additional decoding. T he
SSC mode can also be used with microprocessors such as the
68HC11 and 68HC05, which allow an external device to clock
their serial port.
SCLK will become active and the data word currently in the
output register will be transmitted, MSB first. After the LSB has
been transmitted DRDY will go high until the new data word
becomes available. If CS, having been brought low, is taken
high again at any time during data transmission, SDAT A and
SCLK will go three-state after the current bit finishes. If CS is
subsequently brought low, transmission will resume with the
next bit during the subsequent digital computation period. If
transmission has not been initiated and completed by the time
the next data word is available, DRDY will go high for four
clock cycles then low again as the new word is loaded into the
output register.
Figure 15 shows the timing diagram for the SSC mode. Data is
clocked out by an internally generated serial clock. T he
AD7703 divides each sampling interval into sixteen distinct
periods. Eight periods of 64 clock pulses are for analog settling
and eight periods of 64 clock pulses are for digital computation.
T he status of CS is polled at the beginning of each digital
computation period. If it is low at any of these times, then
A more detailed diagram of the data transmission in the SSC
mode is shown in Figure 16. Data bits change on the falling
edge of SCLK and are valid on the rising edge of SCLK.
1024 CLKIN CYCLES
64 CLKIN
CYCLES
64 CLKIN
CYCLES
INTERNAL
STATUS
ANALOG TIME 0
DIGITAL TIME 0
DIGITAL TIME 7
72 CLKIN CYCLES
DRDY (O)
CS POLLED
CS (I)
HI-Z
HI-Z
SCLK (O)
MSB
LSB
HI-Z
HI-Z
SDATA (O)
Figure 15. Tim ing Diagram for SSC Data Transm ission Mode
CLKIN (I)
72
CLKIN
CYCLES
DRDY (O)
CS (I)
HI-Z
HI-Z
HI-Z
HI-Z
SDATA (O)
DB18
DB19 (MSB)
DB17
DB2
DB1
DB0 (LSB)
SCLK (O)
Figure 16. SSC Mode Showing Data Tim ing Relative to SCLK
–14–
REV. D
AD7703
SYNCH RO NO US EXTERNAL CLO CK MO D E (SEC)
T he SEC mode (MODE pin grounded) is designed for direct
interface to the synchronous serial ports of industry standard
microprocessors such as the 68HC11 and 68HC05. T he SEC
mode also allows customized interfaces, using I/O port pins, to
microprocessors that do not have a direct fit with the AD7703’s
other mode.
D IGITAL NO ISE AND O UTP UT LO AD ING
As mentioned earlier, the AD7703 divides its internal timing
into two distinct phases, analog sampling and settling and digital
computation. In the SSC mode, data is transmitted only during
the digital computation periods, to minimize the effects of
digital noise on analog performance. In the SEC mode data
transmission is externally controlled, so this automatic safeguard
does not exist. T o compensate, the AD7703 should be
synchronized to the digital system clock via CLKIN when used
in the SEC mode.
As shown in Figure 17, a falling edge on CS enables the serial
data output with the MSB initially valid. Subsequent data bits
change on the falling edge of an externally supplied SCLK.
After the LSB has been transmitted, DRDY and SDAT A go
three-state. If CS is low and the AD7703 is still transmitting
data when a new data word becomes available, the old data
word continues to be transmitted and the new data is lost.
Whatever mode of operation is used, resistive and capacitive
loads on digital outputs should be minimized in order to reduce
crosstalk between analog and digital portions of the circuit. For
this reason connection to low-power CMOS logic such as one of
the 4000 series or 74C families is recommended.
If CS is taken high at any time during data transmission,
SDAT A will go three-state immediately. If CS returns low, the
AD7703 will continue transmission with the same data bit. If
transmission has not been initiated and completed by the time
the next data word becomes available, and if CS is high, DRDY
will return high for four clock cycles, then fall as the new word is
loaded into the output register.
DRDY (O)
CS (I)
SCLK (O)
HI-Z
HI-Z
SDATA (O)
DB18
DB19 (MSB)
DB17
DB2
DB1
DB0 (LSB)
Figure 17. Tim ing Diagram for the SEC Mode
REV. D
–15–
AD7703
MECH ANICAL INFO RMATIO N
D imensions shown in inches and (mm)
20-P in P lastic D IP (Suffix N)
20-P in Cer dip (Suffix Q)
20-Lead SO IC (Suffix R)
–16–
REV. D
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明