AD7782BRU-REEL7 [ADI]
IC 2-CH 24-BIT DELTA-SIGMA ADC, SERIAL ACCESS, PDSO16, PLASTIC, TSSOP-16, Analog to Digital Converter;型号: | AD7782BRU-REEL7 |
厂家: | ADI |
描述: | IC 2-CH 24-BIT DELTA-SIGMA ADC, SERIAL ACCESS, PDSO16, PLASTIC, TSSOP-16, Analog to Digital Converter 光电二极管 转换器 |
文件: | 总12页 (文件大小:123K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Read Only, Pin Configured
a
24-Bit ⌺-⌬ ADC
AD7782
FEATURES
FUNCTIONAL BLOCK DIAGRAM
2-Channel, 24-Bit ⌺-⌬ ADC
Pin Configurable (No Programmable Registers)
Pin Selectable Input Channels
V
GND
REFIN(+) REFIN(–) XTAL1 XTAL2
DD
Pin Programmable Input Ranges (؎2.56 V or ؎160 mV)
Fixed 19.79 Hz Update Rate
Simultaneous 50 Hz and 60 Hz Rejection
24-Bit No Missing Codes
OSCILLATOR
AND
AD7782
PLL
AIN1(+)
AIN1(–)
AIN2(+)
AIN2(–)
DOUT/RDY
SCLK
18.5-Bit p-p Resolution (؎2.56 V Range)
16.5-Bit p-p Resolution (؎160 mV Range)
SERIAL
INTERFACE
24-BIT ⌺-⌬
ADC
MUX
BUF
PGA
AND
CONTROL
LOGIC
MODE
INTERFACE
Master or Slave Mode of Operation
Slave Mode
CS
3-Wire Serial
SPI™, QSPI™, MICROWIRE™, and DSP-Compatible
Schmitt Trigger on SCLK
CH1/CH2
RANGE
POWER
Specified for Single 3 V and 5 V Operation
Normal: 1.3 mA @ 3 V
Power-Down: 9 A
BASIC CONNECTION DIAGRAM
POWER SUPPLY
V
ON-CHIP FUNCTIONS
DD
Rail-Rail Input Buffer and PGA
AD7782
AIN1(+)
AIN1(–)
ANALOG
INPUT
CS
APPLICATIONS
DIGITAL
DOUT/RDY
SCLK
Sensor Measurement
Industrial Process Control
Temperature Measurement
Pressure Measurements
Weigh Scales
INTERFACE
AIN2(+)
AIN2(–)
ANALOG
INPUT
XTAL1
32.768kHz
CRYSTAL
REFIN(+)
REFIN(–)
REFERENCE
INPUT
XTAL2
GND
Portable Instrumentation
GENERAL DESCRIPTION
The device operates from a 32.768 kHz crystal with an on-chip PLL
generating the required internal operating frequency. The output
data rate from the part is fixed via the master clock at 19.79 Hz and
provides simultaneous 50 Hz and 60 Hz rejection at this update
rate. Eighteen-bit p-p resolution can be obtained at this update rate.
The AD7782 is a complete analog front end for low-frequency
measurement applications. The 24-bit sigma-delta ADC contains
two fully differential analog input channels that can be config-
ured with a gain of 1 or 16 allowing full-scale input signal ranges
of 2.56 V or 160 mV from a +2.5 V differential reference
input.
The part operates from a single 3 V or 5 V supply. When operating
from 3 V supplies, the power dissipation for the part is 3.9 mW.
The AD7782 is available in a 16-lead TSSOP package.
The AD7782 has an extremely simple, read-only digital interface
which can be operated in master mode or slave mode. There are
no on-chip registers to be programmed. The input signal range
and input channel selection are configured using two external pins.
Another part in the AD778x family is the AD7783. It is similar
to the AD7782 except it has two integrated current sources and
only one differential input channel.
SPI and QSPI are trademarks of Motorola Inc.
MICROWIRE is a trademark of National Semiconductor Corporation.
REV. 0
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties that
may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
Fax: 781/326-8703
www.analog.com
© Analog Devices, Inc., 2001
DD = 2.7 V to 3.6 V or 4.75 V to 5.25 V, REFIN(+) = 2.5 V; REFIN(–) = GND; GND = 0 V;
AD7782–SPECIFICATIONS (XVTAL1/XTAL2 = 32.768 kHz Crystal; all specifications TMIN to TMAX unless otherwise noted.)
Parameter
AD7782B
Unit
Test Conditions
ADC CHANNEL SPECIFICATION
Output Update Rate
19.79
Hz nom
ADC CHANNEL
No Missing Codes2
Resolution
24
16
18
Bits min
Bits p-p
Bits p-p
160 mV Range, RANGE = 0
2.56 V Range, RANGE = 1
Output Noise
Integral Nonlinearity
See Table I
10
2 × 1.024 REFIN
FSR =
Typically 2 ppm
ppm of FSR max
Gain
Offset Error
Offset Error Drift vs. Temperature
Full-Scale Error
Gain Drift vs. Temperature
Power Supply Rejection (PSR)
3
10
10
0.5
100
85
µV typ
nV/°C typ
µV typ
ppm/°C typ
dB typ
dB typ
AIN(+) = AIN(–) = 2.5 V
VDD = 3 V
Input Range = 160 mV, VIN = 1/16 V
Input Range = 2.56 V, VIN = 1 V
ANALOG INPUTS
Differential Input Voltage Ranges
160
2.56
2
mV nom
V nom
µV typ
V min
RANGE = 0
RANGE = 1
Input Voltage = 159 mV on Both Ranges
ADC Range Matching
Absolute AIN Voltage Limits
GND + 100 mV
VDD – 100 mV
V max
Analog Input Current2
DC Input Current
DC Input Current Drift
Normal-Mode Rejection2, 3
@ 50 Hz
1
5
nA max
pA /°C typ
60
94
dB min
dB min
50 Hz 1 Hz
60 Hz 1 Hz
@ 60 Hz
Common-Mode Rejection
@ DC
Input Range = 160 mV, VIN = 1/16 V
125 dB typ, 110 dB typ when Input Range = 2.56 V
50 Hz 1 Hz
105
100
100
dB min
dB min
dB min
@ 50 Hz2
@ 60 Hz2
60 Hz 1 Hz
REFERENCE INPUT
REFIN Voltage
2.5
1
V nom
V min
REFIN = REFIN(+) – REFIN(–)
REFIN Voltage Range2
VDD
V max
V min
V max
µA/V typ
nA/V/°C typ
Absolute REFIN Voltage Limits2
GND – 30 mV
VDD + 30 mV
0.5
Average Reference Input Current
Average Reference Input Current Drift
Normal-Mode Rejection2, 3
@ 50 Hz
0.01
60
94
dB min
dB min
50 Hz 1 Hz
60 Hz 1 Hz
@ 60 Hz
Common-Mode Rejection
@ DC
@ 50 Hz
Input Range = 160 mV, VIN = 1/16 V
100
110
110
dB typ
dB typ
dB typ
50 Hz 1 Hz
60 Hz 1 Hz
@ 60 Hz
LOGIC INPUTS
All Inputs Except SCLK and XTAL12
VINL, Input Low Voltage
0.8
0.4
2.0
V max
V max
V min
VDD = 5 V
VDD = 3 V
VDD = 3 V or 5 V
VINH, Input High Voltage
SCLK Only (Schmitt-Triggered Input)2
VT(+)
VT(–)
VT(+) – VT(–)
VT(+)
VT(–)
1.4/2
V min/V max
V min/V max
V min/V max
V min/V max
V min/V max
V min/V max
VDD = 5 V
VDD = 5 V
VDD = 5 V
VDD = 3 V
VDD = 3 V
VDD = 3 V
0.8/1.4
0.3/0.85
0.95/2
0.4/1.1
0.3/0.85
VT(+) – VT(–)
REV. 0
–2–
AD7782
Parameter
AD7782B
Unit
Test Conditions
LOGIC INPUTS (continued)
XTAL1 Only2
VINL, Input Low Voltage
VINH, Input High Voltage
VINL, Input Low Voltage
VINH, Input High Voltage
Input Currents
0.8
3.5
0.4
2.5
1
–70
10
V max
V min
V max
V min
µA max
µA max
pF typ
VDD = 5 V
VDD = 5 V
VDD = 3 V
VDD = 3 V
VIN = VDD
VIN = GND, Typically –40 µA at 5 V and –20 µA at 3 V
All Digital Inputs
Input Capacitance
LOGIC OUTPUTS (Excluding XTAL2)
VOH, Output High Voltage2
VOL, Output Low Voltage2
VDD – 0.6
0.4
4
0.4
10
10
V min
V max
V min
V max
µA max
pF typ
VDD = 3 V, ISOURCE = 100 µA
VDD = 3 V, ISINK = 100 µA
VDD = 5 V, ISOURCE = 200 µA
VDD = 5 V, ISINK = 1.6 mA
VOH, Output High Voltage2
VOL, Output Low Voltage2
Floating-State Leakage Current
Floating-State Output Capacitance
Data Output Coding
Offset Binary
START-UP TIME
From Power-On
300
ms typ
POWER REQUIREMENTS
Power Supply Voltage
VDD – GND
2.7/3.6
4.75/5.25
V min/max
V min/max
VDD = 3 V nom
VDD = 5 V nom
Power Supply Currents
IDD Current (Normal Mode)4
1.5
1.7
9
mA max
mA max
µA max
µA max
VDD = 3 V, 1.3 mA typ
VDD = 5 V, 1.5 mA typ
VDD = 3 V, 6 µA typ
VDD = 5 V, 20 µA typ
IDD (Power-Down Mode, CS = 1)
24
NOTES
1Temperature Range –40°C to +85°C.
2Guaranteed by design and/or characterization data on production release.
3When a 28.8 kHz crystal is used, normal mode rejection is improved so that the rejection equals 75 dB at 50 1 Hz and equals 66 dB at 60 1 Hz.
4Normal Mode refers to the case where the ADC is running.
Specifications subject to change without notice.
REV. 0
–3–
AD7782
(VDD = 2.7 V to 3.6 V or VDD = 4.75 V to 5.25 V; GND = 0 V; XTAL = 32.768 kHz; Input Logic 0 = 0 V,
Logic 1 = VDD unless otherwise noted.)
TIMING CHARACTERISTICS1, 2
Limit at TMIN, TMAX
(B Version)
Parameter
Unit
Conditions/Comments
t1
tADC
t2
30.5176
50.54
0
0
60
80
2 × tADC
0
60
80
10
80
0
10
80
µs typ
Crystal Oscillator Period
19.79 Hz Update Rate
CH1/CH2 Select to CS Setup Time
CS Falling Edge to DOUT Active
VDD = 4.75 V to 5.25 V
ms typ
ns min
ns min
ns max
ns max
ns typ
t3
VDD = 2.7 V to 3.6 V
t43
t5
Channel Settling Time
ns min
ns max
ns max
ns min
ns max
ns min
ns min
ns max
SCLK Active Edge to Data Valid Delay4
VDD = 4.75 V to 5.25 V
VDD = 2.7 V to 3.6 V
Bus Relinquish Time after CS Inactive Edge
5
t8
t9
t10
CS Rising Edge to SCLK Inactive Edge Hold Time
SCLK Inactive to DOUT High
Slave Mode Timing
t6
t7
100
100
ns min
ns min
SCLK High Pulsewidth
SCLK Low Pulsewidth
Master Mode Timing
t6
t7
t11
t1/2
t1/2
t1/2
3t1/2
µs typ
µs typ
µs min
µs max
SCLK High Pulsewidth
SCLK Low Pulsewidth
DOUT Low to First SCLK Active Edge4
NOTES
1Sample tested during initial release to ensure compliance. All input signals are specified with tR = tF = 5 ns (10% to 90% of VDD) and timed from a voltage level of 1.6 V.
2See Figure 2.
3These numbers are measured with the load circuit of Figure 1 and defined as the time required for the output to cross the VOL or VOH limits.
4SCLK active edge is falling edge of SCLK.
5These numbers are derived from the measured time taken by the data output to change 0.5 V when loaded with the circuit of Figure 1. The measured number is then extrapolated
back to remove effects of charging or discharging the 50 pF capacitor. This means that the times quoted in the timing characteristics are the true bus relinquish times of the part
and as such are independent of external bus loading capacitances.
I
(1.6mAWITH V = 5V
DD
SINK
100AWITH V = 3V)
DD
TO OUTPUT
PIN
1.6V
50pF
I
(200AWITH V = 5V
DD
SOURCE
100AWITH V = 3V)
DD
Figure 1. Load Circuit for Timing Characterization
REV. 0
–4–
AD7782
CH1/CH2 (I)
CS (I)
t2
t3
t9
t8
t4
DOUT/RDY
MSB
LSB
t10
MSB
LSB
t5
t7
SLAVE MODE
SCLK (I)
t6
t5
t11
t7
MASTER MODE
SCLK (O)
t6
I = INPUT TO AD7782, O = OUTPUT FROM AD7782
SLAVE MODE IS SELECTED BYTYINGTHE MODE PIN LOW, WHILE MASTER MODE IS SELECTED BYTYINGTHE MODE PIN HIGH.
Figure 2. Slave/Master Mode Timing Diagram
ABSOLUTE MAXIMUM RATINGS
*
TSSOP Package
(TA = 25°C unless otherwise noted)
θ
JA Thermal Impedance . . . . . . . . . . . . . . . . . . . . .97.9°C/W
VDD to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V
Analog Input Voltage to GND . . . . . . . . –0.3 V to VDD + 0.3 V
Reference Input Voltage to GND . . . . . –0.3 V to VDD + 0.3 V
Total AIN/REFIN Current (Indefinite) . . . . . . . . . . . . . 30 mA
Digital Input Voltage to GND . . . . . . . . –0.3 V to VDD + 0.3 V
Digital Output Voltage to GND . . . . . . –0.3 V to VDD + 0.3 V
Operating Temperature Range . . . . . . . . . . . . –40°C to +85°C
Storage Temperature Range . . . . . . . . . . . . . –65°C to +150°C
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C
θ
JC Thermal Impedance . . . . . . . . . . . . . . . . . . . . . . 14°C/W
Lead Temperature, Soldering
Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . . . . 215°C
Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220°C
*Stresses above those listed under Absolute Maximum Ratings may cause per-
manent damage to the device. This is a stress rating only; functional operation of
the device at these or any other conditions above those listed in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
ORDERING GUIDE
Temperature Range Package Description
Model
Package Option
AD7782BRU
EVAL-AD7782EB
–40°C to +85°C
TSSOP
Evaluation Board
RU-16
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the AD7782 features proprietary ESD protection circuitry, permanent damage may occur on
devices subjected to high-energy electrostatic discharges. Therefore, proper ESD precautions are
recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
REV. 0
–5–
AD7782
PIN CONFIGURATION
XTAL1
REFIN(+)
REFIN(–)
AIN1(+)
1
2
3
4
5
6
7
8
16
15
14
XTAL2
V
DD
GND
13 MODE
12 DOUT/RDY
11 CS
AD7782
TOP VIEW
AIN1(–)
(Not to Scale)
AIN2(+)
10 SCLK
AIN2(–)
9
RANGE
CH1/CH2
PIN FUNCTION DESCRIPTIONS
Pin No. Mnemonic
Function
1
2
XTAL1
REFIN(+)
Input to the 32.768 kHz Crystal Oscillator Inverter.
Positive Reference Input. REFIN(+) can lie anywhere between VDD and GND +1 V. The nominal reference
voltage (REFIN(+) – REFIN(–)) is 2.5 V, but the part functions with a reference from 1 V to VDD
.
3
4
5
6
7
8
REFIN(–)
AIN1(+)
AIN1(–)
AIN2(+)
AIN2(–)
CH1/CH2
Negative Reference Input. This reference input can lie anywhere between GND and VDD – 1 V.
Analog Input. AIN1(+) is the positive terminal of the fully-differential analog input pair AIN1(+)/AIN1(–).
Analog Input. AIN1(–) is the negative terminal of the fully-differential analog input pair AIN1(+)/AIN1(–).
Analog Input. AIN2(+) is the positive terminal of the fully-differential analog input pair AIN2(+)/AIN2(–).
Analog Input. AIN2(–) is the negative terminal of the fully-differential analog input pair AIN2(+)/AIN2(–).
Channel Select, Logic Input. With CH1/CH2 = 0, channel AIN1(+)/AIN1(–) is selected while the active
channel is AIN2(+)/AIN2(–) when CH1/CH2 = 1.
9
RANGE
SCLK
Logic Input which configures the input range on the internal PGA. With RANGE = 0, the full-scale input
range is 160 mV while the full-scale input range equals 2.56 V when RANGE = 1 for a +2.5 V Reference.
10
Serial Clock Input/Output for Data Transfers from the ADC. When the device is operated in master mode,
SCLK is an output with one SCLK period equal to one XTAL period. In slave mode, SCLK is generated
by an external source. In slave mode, all the data can be transmitted on a continuous train of pulses.
Alternatively, SCLK can be a noncontinuous clock with the information being transmitted from the AD7782
in smaller batches of data. SCLK is Schmitt triggered (slave mode) making the interface suitable for opto-
isolated applications.
11
12
CS
Chip Select Input. CS is an active low logic input used to select the AD7782. When CS is low, the PLL
establishes lock and allows the AD7782 to initiate a conversion on the selected channel. When CS is high,
the conversion is aborted, DOUT and SCLK are three-stated, the AD7782 enters standby mode and any
conversion result in the output shift register is lost.
DOUT/RDY Serial Data Output/Data Ready Output. DOUT/RDY serves a dual purpose in this interface. When a con-
version is initiated, DOUT/RDY goes high and remains high until the conversion is complete. DOUT/RDY
will then return low to indicate that valid data is available to be read from the device. In slave mode, this acts
as an interrupt to the processor indicating that valid data is available. If data is not read after a conversion,
DOUT/RDY will go high before the next update occurs. In master mode, DOUT/RDY goes low for at least
half an SCLK cycle before the device produces SCLKs. When SCLK becomes active, data is output on
the DOUT/RDY pin. Data is output on the falling SCLK edge and is valid on the rising edge.
13
MODE
The MODE pin selects master or slave mode of operation. When MODE = 0, the AD7782 operates in
master mode while the AD7782 is configured for slave mode when MODE = 1.
14
15
16
GND
VDD
XTAL2
Ground Reference Point for the AD7782.
Supply Voltage, 3 V or 5 V Nominal.
Output from the 32.768 kHz Crystal Oscillator Inverter.
–6–
REV. 0
AD7782
Typical Performance Characteristics
9
8
7
6
5
4
3
2
3.0
2.5
2.0
1.5
1.0
0.5
0
؎2.56V RANGE
V
= 5V
DD
V
= 2.5V
REF
= 25؇C
T
A
؎160mV RANGE
1
0
1.0
1.5
2.0
2.5
3.0
– V
3.5
4.0
4.5
5.0
V
REF
TPC 1. Noise Distribution Histogram
TPC 2. RMS Noise vs. Reference Input
ADC CIRCUIT INFORMATION
Overview
The output rate of the AD7782 (fADC) equals:
fADC = 32.768 × 103 / 69 × 8 × 3
(
)
The AD7782 incorporates an analog multiplexer with a Σ-∆ ADC
channel, on-chip programmable gain amplifier, and on-chip digital
filtering intended for the measurement of wide dynamic range,
low-frequency signals such as those in weigh-scale, strain-gage,
pressure transducer, or temperature measurement applications.
while the settling time equals:
2
tSETTLE
=
= 2 × tADC
f
ADC
This ADC input is buffered and can be programmed to have an
input voltage range of 160 mV or 2.56 V. The input channels
are configured as two fully differential inputs. Buffering the input
channels means that the part can accommodate significant source
impedances on the analog inputs and that R, C filtering (for
noise rejection or RFI reduction) can be placed on the analog
inputs if required. The device requires an external reference of
+2.5 V nominal. Figure 3 shows the basic connections required
to operate the part.
Normal-mode rejection is the major function of the digital filter on
the AD7782. Simultaneous 50 Hz and 60 Hz rejection of better
than 60 dB is achieved as notches are placed at both 50 Hz and
60 Hz. Figure 4 shows the filter rejection.
0
–20
–40
POWER
SUPPLY
10F
0.1F
–60
–80
–100
–120
–140
–160
IN+
V
DD
AD7782
OUT+
OUT–
AIN1(+)
CS
AIN1(–)
CONTROLLER
IN–
DOUT/RDY
AIN2(+)
AIN2(–)
SCLK
0
10
20
30
40
50
60
70
80
90
100
10k⍀
6k⍀
FREQUENCY – Hz
XTAL1
XTAL2
32.768kHz
CRYSTAL
OUTPUT DATA RATE = 19.8Hz
INPUT BANDWIDTH = 4.74Hz
50Hz REJECTION = –66dB, 50Hz ؎1Hz REJECTION = –60dB
60Hz REJECTION = –117dB, 60Hz ؎1Hz REJECTION = –94dB
REFIN(+)
REFIN(–)
GND
Figure 4. Filter Profile (Filter Notches at
Both 50 Hz and 60 Hz)
Figure 3. Basic Connection Diagram
REV. 0
–7–
AD7782
NOISE PERFORMANCE
MASTER MODE (MODE = 0)
Table I shows the output rms noise and output peak-to-peak
resolution in bits (rounded to the nearest 0.5 LSB) for the two
input voltage ranges. The numbers are typical and generated at
a differential input voltage of 0 V. The peak-to-peak resolution
figures represent the resolution for which there will be no code
flicker within a six-sigma limit. The output noise comes from
two sources. The first is the electrical noise in the semiconduc-
tor devices (device noise) used in the implementation of the
modulator. Secondly, when the analog input is converted into
the digital domain, quantization noise is added. The device
noise is at a low level and is independent of frequency. The
quantization noise starts at an even lower level but rises rapidly
with increasing frequency to become the dominant noise source.
In this mode, SCLK is provided by the AD7782. With CS low,
SCLK becomes active when a conversion is complete and generates
twenty four falling and rising edges. The DOUT/RDY pin, which
is normally high, goes low to indicate that a conversion is complete.
Data is output on the DOUT/RDY pin following the SCLK falling
edge and is valid on the SCLK rising edge. When the 24-bit word
has been output, SCLK idles high until the next conversion is
complete. DOUT/RDY returns high and will remain high until
another conversion is available. It then operates as a RDY signal
again. The part will continue to convert until CS is taken high.
SCLK and DOUT/RDY are three-stated when CS is taken high.
SLAVE MODE (MODE = 1)
In slave mode, the SCLK is generated externally. SCLK must
idle high between data transfers. With CS low, DOUT/RDY
goes low when a conversion is complete. Twenty four SCLK
pulses are needed to transfer the digital word from the AD7782.
Twenty four consecutive pulses can be generated or, alterna-
tively, the data transfer can be split into batches. This is useful
when interfacing to a microcontroller which uses 8-bit transfers.
Data is output following the SCLK falling edge and is valid on
the SCLK rising edge.
Table I. Typical Output RMS Noise and
Peak-to-Peak Resolution vs. Input Range
Input Range
؎160 mV
؎2.56 V
Noise (µV)
0.65
2.30
Peak-to-Peak Resolution (Bits)
16.5
18.5
CIRCUIT DESCRIPTION
Analog Input Channels
DIGITAL INTERFACE
The AD7782’s serial interface consists of four signals, CS, SCLK,
DOUT/RDY, and MODE. The MODE pin is used to select the
master/slave mode of operation. When the part is configured as
a master, SCLK is an output while SCLK is an input when
slave mode is selected. Data transfers take place with respect to
this SCLK signal. The DOUT/RDY line is used for accessing
data from the data register. This pin also functions as a RDY
line. When a conversion is complete, DOUT/RDY goes low to
indicate that data is ready to be read from the AD7782’s data
register. It is reset high when a read operation from the data
register is complete. It also goes high prior to the updating of
the output register to indicate when not to read from the device
to ensure that a data read is not attempted while the register is
being updated. The digital conversion is also output on this pin.
The ADC has two fully differential input channels. Pin CH1/CH2
is used to select the channels. When CH1/CH2 is low, channel
AIN1(+) – AIN1(–) are selected while channel AIN2(+) – AIN2(–)
are selected when CH1/CH2 is high. When the analog input
channel is switched, the settling time of the part must elapse
before a new valid word is available from the ADC.
The output of the ADC multiplexer feeds into a high-impedance
input stage of the buffer amplifier. As a result, the ADC inputs
can handle significant source impedances and are tailored for direct
connection to external resistive-type sensors like strain gages or
Resistance Temperature Detectors (RTDs).
The absolute input voltage range on the ADC inputs is restricted
to a range between GND + 100 mV and VDD – 100 mV. Care
must be taken in setting up the common-mode voltage and input
voltage range so that these limits are not exceeded; otherwise
there will be a degradation in linearity and noise performance.
CS is used to select the device and to place the device in standby
mode. When CS is taken low, the AD7782 is powered up, the
PLL locks and the device initiates a conversion on the selected
channel. The device will continue to convert until CS is taken
high. When CS is taken high, the AD7782 is placed in standby
mode minimizing the current consumption. The conversion is
aborted, DOUT and SCLK are three-stated and the result in
the data register is lost.
Programmable Gain Amplifier
The output from the buffer on the ADC is applied to the input of
the on-chip programmable gain amplifier (PGA). The PGA gain
range is programmed via pin RANGE. With an external 2.5 V refer-
ence applied, the PGA can be programmed to have a bipolar range
of 160 mV (RANGE = 0) or 2.56 V (RANGE = 1). These
are the ranges that should appear at the input to the on-chip PGA.
Figure 2 shows the timing diagram for interfacing to the AD7782
with CS used to decode the part.
–8–
REV. 0
AD7782
Bipolar Configuration/Output Coding
without introducing gain errors in the system. Deriving the refer-
ence input voltage across an external resistor will mean that the
reference input sees a significant external source impedance. Exter-
nal decoupling on the REFIN pins would not be recommended in
this type of circuit configuration.
The analog inputs on the AD7782 accept bipolar input voltage
ranges. Signals on the AIN(+) input of the ADC are referenced
to the voltage on the respective AIN(–) input. For example, if
AIN(–) is 2.5 V and the AD7782 is configured for an analog input
range of 160 mV, the analog input range on the AIN(+) input
is 2.34 V to 2.66 V (i.e., 2.5 V 0.16 V).
Grounding and Layout
Since the analog inputs and reference inputs on the ADC are
differential, most of the voltages in the analog modulator are common-
mode voltages. The excellent common-mode rejection of the part
will remove common-mode noise on these inputs. The digital filter
will provide rejection of broadband noise on the power supply,
except at integer multiples of the modulator sampling frequency.
The digital filter also removes noise from the analog and reference
inputs provided these noise sources do not saturate the analog
modulator. As a result, the AD7782 is more immune to noise inter-
ference than a conventional high-resolution converter. However,
because the resolution of the AD7782 is so high, and the noise
levels from the AD7782 so low, care must be taken with regard to
grounding and layout.
The coding is offset binary with a negative full-scale voltage
resulting in a code of 000 . . . 000, a zero differential voltage
resulting in a code of 100 . . . 000, and a positive full-scale
voltage resulting in a code of 111 . . . 111. The output code for
any analog input voltage can be represented as follows:
Code = 2N −1
×
AIN × GAIN / 1.024 ×V
+ 1
(
)
)
(
[
REF
]
Where AIN is the analog input voltage, GAIN is the PGA gain, i.e.,
1 on the 2.56 V range and 16 on the 160 mV range and N = 24.
Crystal Oscillator
The AD7782 is intended for use with a 32.768 kHz watch crystal.
A PLL internally locks onto a multiple of this frequency to provide
a stable 4.194304 MHz clock for the ADC. The modulator sample
rate is the same as the crystal oscillator frequency. The start-up
time associated with 32.768 kHz crystals is typically 300 ms. In
some cases, it will be necessary to connect capacitors on the crystal
to ensure that it does not oscillate at overtones of its fundamental
operating frequency. The values of capacitors will vary depending
on the manufacturer’s specifications.
The printed circuit board that houses the AD7782 should be
designed such that the analog and digital sections are separated
and confined to certain areas of the board. A minimum etch tech-
nique is generally best for ground planes as it gives the best shielding.
It is recommended that the AD7782’s GND pin be tied to the
AGND plane of the system. In any layout, it is important that the
user keep in mind the flow of currents in the system, ensuring
that the return paths for all currents are as close as possible to the
paths the currents took to reach their destinations. Avoid forcing
digital currents to flow through the AGND sections of the layout.
Reference Input
The AD7782 has a fully-differential reference input capability
for the channel. The common-mode range for these differential
inputs is from GND to VDD. The reference input is unbuffered and
therefore excessive R-C source impedances will introduce gain
errors. The reference voltage REFIN (REFIN(+) – REFIN(–)) is
2.5 V nominal for specified operation but the AD7782 is functional
with reference voltages from 1 V to VDD. In applications where the
excitation (voltage or current) for the transducer on the analog
input also drives the reference voltage for the part, the effect of the
low frequency noise in the excitation source will be removed as the
application is ratiometric. If the AD7782 is used in a nonratiometric
application, a low noise reference should be used. Recommended
reference voltage sources for the AD7782 include the AD780,
REF43, and REF192. It should also be noted that the reference
inputs provide a high impedance, dynamic load. Because the input
impedance of each reference input is dynamic, resistor/capacitor
combinations on these inputs can cause dc gain errors, depending
on the output impedance of the source that is driving the reference
inputs. Reference voltage sources like those recommended above
(e.g., AD780) will typically have low output impedances and are
therefore tolerant to having decoupling capacitors on the REFIN(+)
The AD7782’s ground plane should be allowed to run under the
AD7782 to prevent noise coupling. The power supply lines to the
AD7782 should use as wide a trace as possible to provide low imped-
ance paths and reduce the effects of glitches on the power supply
line. Fast switching signals like clocks should be shielded with digital
ground to avoid radiating noise to other sections of the board, and
clock signals should never be run near the analog inputs. Avoid
crossover of digital and analog signals. Traces on opposite sides of
the board should run at right angles to each other. This will reduce the
effects of feedthrough through the board. A microstrip technique
is by far the best, but is not always possible with a double-sided
board. In this technique, the component side of the board is dedi-
cated to ground planes while signals are placed on the solder side.
Good decoupling is important when using high-resolution ADCs.
VDD should be decoupled with 10 µF tantalum in parallel with
0.1 µF capacitors to GND. To achieve the best from these decoupling
components, they have to be placed as close as possible to the
device, ideally right up against the device. All logic chips should
be decoupled with 0.1 µF ceramic capacitors to DGND.
REV. 0
–9–
AD7782
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
16-Lead Thin Shrink SO Plastic (TSSOP)
(RU-16)
0.201 (5.10)
0.193 (4.90)
16
9
0.177 (4.50)
0.169 (4.30)
0.256 (6.50)
0.246 (6.25)
1
8
PIN 1
0.0433 (1.10)
MAX
0.006 (0.15)
0.002 (0.05)
8؇
0؇
0.0256 (0.65) 0.0118 (0.30)
0.028 (0.70)
0.020 (0.50)
0.0079 (0.20)
0.0035 (0.090)
SEATING
PLANE
BSC
0.0075 (0.19)
–10–
REV. 0
–11–
–12–
相关型号:
©2020 ICPDF网 联系我们和版权申明