AD7783BRUZ-REEL7 [ADI]
Read-Only, Pin Configured 24-Bit ADC;
| 型号： | AD7783BRUZ-REEL7 |
| 厂家： | 
ADI |
| 描述： | Read-Only, Pin Configured 24-Bit ADC |
| 文件： | 总13页 (文件大小：318K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Read-Only, Pin Configured 24-Bit ⌺-⌬ ADC
with Excitation Current Sources
AD7783
FEATURES
FUNCTIONAL BLOCK DIAGRAM
Single-Channel, 24-Bit ⌺-⌬ ADC
Pin Configurable (No Programmable Registers)
ISOURCE Select™
Pin Programmable Input Ranges (±2.56 V or ±160 mV)
Fixed 19.79 Hz Update Rate
V
XTAL1 XTAL2
REFIN(+) REFIN(–)
GND
DD
V
DD
IEXC1
IEXC2
200A
200A
IOUT1
OSCILLATOR
AND
Simultaneous 50 Hz and 60 Hz Rejection
24-Bit No Missing Codes
PLL
IOUT2
IPIN
18.5-Bit p-p Resolution (±2.56 V Range)
DOUT/RDY
SCLK
SERIAL
INTERFACE
AND
CONTROL
LOGIC
16.5-Bit p-p Resolution (±160 mV Range)
AIN(+)
AIN(–)
24-BIT ⌺-⌬
ADC
MUX
BUF
PGA
INTERFACE
MODE
Master or Slave Mode of Operation
Slave Mode
CS
AD7783
3-Wire Serial
SPI®, QSPI™, MICROWIRE™, and DSP-Compatible
Schmitt Trigger on SCLK
RANGE
POWER
Specified for Single 3 V and 5 V Operation
Normal: 1.3 mA @ 3 V
Power-Down: 9 A
BASIC CONNECTION DIAGRAM
POWER SUPPLY
ON-CHIP FUNCTIONS
Rail-to-Rail Input Buffer and PGA
V
DD
AD7783
APPLICATIONS
AIN(+)
AIN(–)
ANALOG
INPUT
CS
Sensor Measurement
Industrial Process Control
Temperature Measurement
Pressure Measurement
Weigh Scales
DIGITAL
INTERFACE
DOUT/RDY
SCLK
IOUT1
IOUT2
CURRENT
SOURCES
XTAL1
32.768kHz
CRYSTAL
REFIN(+)
REFIN(–)
REFERENCE
INPUT
XTAL2
Portable Instrumentation
GND
GENERAL DESCRIPTION
The device operates from a 32.768 kHz crystal with an on-chip
PLL generating the required internal operating frequency. The
output data rate from the part is fixed via the master clock at
19.79 Hz and provides simultaneous 50 Hz and 60 Hz rejection
at this update rate. At this update rate, 18-bit p-p resolution can
be obtained.
The AD7783 is a complete analog front end for low frequency
measurement applications. The 24-bit sigma-delta ADC con-
tains one fully differential input channel that can be configured
with a gain of 1 or 16 allowing full-scale input signal ranges of
±2.56 V or ±160 mV from a +2.5 V differential reference input.
It also contains two 200 mA integrated current sources.
The part operates from a single 3 V or 5 V supply. When oper-
ating from 3 V supplies, the power dissipation for the part is
3.9 mW. The AD7783 is available in a 16-lead TSSOP.
The AD7783 has an extremely simple, read-only digital inter-
face that can be operated in master mode or slave mode.
There are no on-chip registers to be programmed. The input
signal range and current source selection are configured using
two external pins.
Another part in the AD778x family is the AD7782. It is similar
to the AD7783 except it has no integrated current sources and
two differential input channels.
REV. C
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, norforanyinfringementsofpatentsorotherrightsofthirdpartiesthat
may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
www.analog.com
2011
Fax:781/461-3113
©
Analog Devices, Inc. All rights reserved.
AD7783* PRODUCT PAGE QUICK LINKS
Last Content Update: 02/23/2017
COMPARABLE PARTS
View a parametric search of comparable parts.
TOOLS AND SIMULATIONS
• Sigma-Delta ADC Tutorial
EVALUATION KITS
REFERENCE MATERIALS
• AD7783 Evaluation Board
Technical Articles
• Delta-Sigma Rocks RF, As ADC Designers Jump On Jitter
• MS-2210: Designing Power Supplies for High Speed ADC
DOCUMENTATION
Application Notes
• Remote Three-Wire RTDs Can Multiplex Accurately To
Measurement System
• AN-202: An IC Amplifier User’s Guide to Decoupling,
Grounding, and Making Things Go Right for a Change
DESIGN RESOURCES
• AD7783 Material Declaration
• PCN-PDN Information
• Quality And Reliability
• Symbols and Footprints
• AN-311: How to Reliably Protect CMOS Circuits Against
Power Supply Overvoltaging
• AN-397: Electrically Induced Damage to Standard Linear
Integrated Circuits:
• AN-607: Selecting a Low Bandwidth (<15 kSPS) Sigma-
Delta ADC
• AN-608: Input Buffers on Sigma-Delta ADCs
• AN-609: Chopping on Sigma-Delta ADCs
• AN-610: The PGA on Sigma-Delta ADCs
DISCUSSIONS
View all AD7783 EngineerZone Discussions.
• AN-611: 50 Hz/60Hz Rejection on Sigma-Delta ADCs
SAMPLE AND BUY
Visit the product page to see pricing options.
• AN-615: Peak-to-Peak Resolution Versus Effective
Resolution
• AN-968: Current Sources: Options and Circuits
TECHNICAL SUPPORT
Data Sheet
Submit a technical question or find your regional support
number.
• AD7783: Read-Only, Pin Configured 24-Bit Σ-Δ ADC With
Excitation Current Sources Data Sheet
DOCUMENT FEEDBACK
Submit feedback for this data sheet.
This page is dynamically generated by Analog Devices, Inc., and inserted into this data sheet. A dynamic change to the content on this page will not
trigger a change to either the revision number or the content of the product data sheet. This dynamic page may be frequently modified.
AD7783–SPECIFICATIONS1 (VDD = 2.7 V to 3.6 V or 4.75 V to 5.25 V, REFIN(+) = 2.5 V; REFIN(–) = GND;
GND = 0 V; XTAL1/XTAL2 = 32.768 kHz Crystal; all specifications TMIN to TMAX, unless otherwise noted.)
Parameter
AD7783B
Unit
Test Conditions
ADC CHANNEL SPECIFICATION
Output Update Rate
19.79
Hz nom
ADC CHANNEL
No Missing Codes2
Resolution
24
16
18
Bits min
Bits p-p
Bits p-p
±160 mV Range, RANGE = 0
±2.56 V Range, RANGE = 1
Output Noise
Integral Nonlinearity
Offset Error
Offset Error Drift versus Temperature
Full-Scale Error
Gain Drift versus Temperature
Power Supply Rejection (PSR)
See Table I
±10
±3
±10
±10
±0.5
100
85
2 ¥ 1.024 REFIN
FSR =
Typically 2 ppm,
ppm of FSR max
mV typ
nV/∞C typ
mV typ
ppm/∞C typ
dB typ
Gain
AIN(+) = AIN(–) = 2.5 V
VDD = 3 V
Input Range = ±160 mV, VIN = 1/16 V
Input Range = ±2.56 V, VIN = 1 V
dB typ
ANALOG INPUTS
Differential Input Voltage Ranges
±160
mV nom
V nom
mV typ
V min
Range = 0
Range = 1
Input Voltage = 159 mV on Both Ranges
±2.56
ADC Range Matching
Absolute AIN Voltage Limits
±2
GND + 100 mV
VDD – 100 mV
V max
Analog Input Current2
DC Input Current
DC Input Current Drift
Normal-Mode Rejection2, 3
@ 50 Hz
@ 60 Hz
Common-Mode Rejection
@ DC
±1
±5
nA max
pA/∞C typ
60
94
dB min
dB min
50 Hz ± 1 Hz
60 Hz ± 1 Hz
Input Range = ±160 mV, VIN = 1/16 V
125 dB typ,
105
dB min
110 dB typ when Input Range = ±2.56 V
@ 50 Hz2
@ 60 Hz2
100
100
dB min
dB min
50 Hz ± 1 Hz
60 Hz ± 1 Hz
REFERENCE INPUT
REFIN Voltage
2.5
1
V nom
V min
REFIN = REFIN(+) – REFIN(–)
REFIN Voltage Range2
VDD
V max
V min
V max
mA/V typ
nA/V/∞C typ
Absolute REFIN Voltage Limits2
GND – 30 mV
VDD + 30 mV
0.5
Average Reference Input Current
Average Reference Input Current Drift ±0.01
Normal-Mode Rejection2, 3
@ 50 Hz
@ 60 Hz
Common-Mode Rejection
@ DC
@ 50 Hz
60
94
dB min
dB min
50 Hz ± 1 Hz
60 Hz ± 1 Hz
Input Range = ±160 mV, VIN = 1/16 V
100
110
110
dB typ
dB typ
dB typ
50 Hz ± 1 Hz
60 Hz ± 1 Hz
@ 60 Hz
EXCITATION CURRENT SOURCES
(IEXC1, IEXC2)
Output Current
Initial Tolerance at 25∞C
Drift
Initial Current Matching at 25∞C
Drift Matching
Line Regulation
Load Regulation
Output Compliance
200
±10
200
±2.5
20
2.5
300
mA
% typ
ppm/∞C typ
% max
ppm/∞C typ
mA/V max
nA/V typ
V max
No Load
VDD = 5 V ± 5%. Typically 1.25 mA/V.
VDD – 0.6
GND – 30 mV
V min
–2–
REV. C
AD7783
Parameter
AD7783B
Unit
Test Conditions
LOGIC INPUTS
All Inputs Except SCLK and XTAL12
VINL, Input Low Voltage
0.8
0.4
2.0
V max
V max
V min
VDD = 5 V
VDD = 3 V
VDD = 3 V or 5 V
VINH, Input High Voltage
SCLK Only (Schmitt-Triggered Input)2
VT(+)
VT(–)
1.4/2
V min/V max
V min/V max
V min/V max
V min/V max
V min/V max
V min/V max
VDD = 5 V
VDD = 5 V
VDD = 5 V
VDD = 3 V
VDD = 3 V
VDD = 3 V
0.8/1.4
0.3/0.85
0.95/2
0.4/1.1
0.3/0.85
V
T(+) – VT(–)
VT(+)
VT(–)
V
T(+) – VT(–)
XTAL1 Only2
VINL, Input Low Voltage
0.8
3.5
0.4
2.5
±1
V max
V min
V max
V min
mA max
mA max
VDD = 5 V
VDD = 5 V
VDD = 3 V
VDD = 3 V
V
INH, Input High Voltage
VINL, Input Low Voltage
VINH, Input High Voltage
Input Currents
V
IN = VDD
–70
VIN = GND, Typically –40 mA at 5 V and
–20 mA at 3 V
All Digital Inputs
Input Capacitance
10
pF typ
LOGIC OUTPUTS (Excluding XTAL2)
VOH, Output High Voltage2
VDD – 0.6
0.4
4
0.4
±10
±10
Offset Binary
V min
V max
V min
V max
mA max
pF typ
VDD = 3 V, ISOURCE = 100 mA
VDD = 3 V, ISINK = 100 mA
VDD = 5 V, ISOURCE = 200 mA
VDD = 5 V, ISINK = 1.6 mA
V
OL, Output Low Voltage2
VOH, Output High Voltage2
VOL, Output Low Voltage2
Floating-State Leakage Current
Floating-State Output Capacitance
Data Output Coding
START-UP TIME
From Power-On
300
ms typ
POWER REQUIREMENTS
Power Supply Voltage
VDD – GND
2.7/3.6
4.75/5.25
V min/V max
V min/V max
VDD = 3 V nom
VDD = 5 V nom
Power Supply Currents
IDD Current (Normal Mode)4
1.5
1.7
9
mA max
mA max
mA max
mA max
VDD = 3 V, 1.3 mA typ
DD = 5 V, 1.5 mA typ
VDD = 3 V, 6 mA typ
VDD = 5 V, 20 mA typ
V
IDD (Power-Down Mode, CS = 1)
24
NOTES
1Temperature range –40∞C to +85∞C.
2Guaranteed by design and/or characterization data on production release.
3When a 28.8 kHz crystal is used, normal-mode rejection is improved so that the rejection equals 75 dB at 50 Hz ±1 Hz and equals 66 dB at 60 Hz ±1 Hz.
4Normal mode refers to the case where the ADC is running.
Specifications subject to change without notice.
REV. C
–3–
AD7783
TIMING CHARACTERISTICS1, 2 (VDD = 2.7 V to 3.6 V or VDD = 4.75 V to 5.25 V; GND = 0 V; XTAL = 32.768 kHz;
Input Logic 0 = 0 V, Logic 1 = VDD, unless otherwise noted.)
Limit at TMIN, TMAX
(B Version)
Parameter
Unit
Conditions/Comments
t1
tADC
t2
30.5176
50.54
0
60
80
2 ¥ tADC
0
60
80
10
80
0
10
ms typ
Crystal Oscillator Period
19.79 Hz Update Rate
CS Falling Edge to DOUT Active
VDD = 4.75 V to 5.25 V
ms typ
ns min
ns max
ns max
ns typ
VDD = 2.7 V to 3.6 V
t33
t4
Channel Settling Time
ns min
ns max
ns max
ns min
ns max
ns min
ns min
ns max
SCLK Active Edge to Data Valid Delay4
VDD = 4.75 V to 5.25 V
VDD = 2.7 V to 3.6 V
Bus Relinquish Time after CS Inactive Edge
5
t7
t8
t9
CS Rising Edge to SCLK Inactive Edge Hold Time
SCLK Inactive to DOUT High
80
Slave Mode Timing
t5
t6
100
100
ns min
ns min
SCLK High Pulse Width
SCLK Low Pulse Width
Master Mode Timing
t5
t6
t10
t1/2
t1/2
t1/2
3t1/2
ms typ
ms typ
ms min
ms max
SCLK High Pulse Width
SCLK Low Pulse Width
DOUT Low to First SCLK Active Edge4
NOTES
1Sample tested during initial release to ensure compliance. All input signals are specified with tR = tF = 5 ns (10% to 90% of VDD) and timed from a voltage level of 1.6 V.
2See Figure 2.
3These numbers are measured with the load circuit of Figure 1 and defined as the time required for the output to cross the VOL or VOH limits.
4SCLK active edge is falling edge of SCLK.
5These numbers are derived from the measured time taken by the data output to change 0.5 V when loaded with the circuit of Figure 1. The measured number is then
extrapolated back to remove effects of charging or discharging the 50 pF capacitor. This means the times quoted in the timing characteristics are the true bus relin-
quish times of the part and as such are independent of external bus loading capacitances.
I
(1.6mAWITH V = 5V
DD
SINK
100AWITH V = 3V)
DD
TO OUTPUT
PIN
1.6V
50pF
I
(200AWITH V = 5V
DD
SOURCE
100AWITH V = 3V)
DD
Figure 1. Load Circuit for Timing Characterization
–4–
REV. C
AD7783
CS (I)
t2
t8
LSB
t7
t3
DOUT/RDY (O)
MSB
MSB
LSB
t9
t4
t6
SLAVE MODE
SCLK (I)
t5
t4
t10
t6
MASTER MODE
SCLK (O)
t5
I = INPUT TO AD7783, AND O = OUTPUT FROM AD7783.
SLAVE MODE IS SELECTED BYTYINGTHE MODE PIN HIGH, WHILE MASTER MODE IS SELECTED BYTYINGTHE MODE PIN LOW.
Figure 2. Slave/Master Mode Timing Diagram
ABSOLUTE MAXIMUM RATINGS*
(TA = 25∞C, unless otherwise noted.)
TSSOP Package
JA Thermal Impedance . . . . . . . . . . . . . . . . . . . . 97.9∞C/W
VDD to GND . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V
Analog Input Voltage to GND . . . . . . . –0.3 V to VDD + 0.3 V
Reference Input Voltage to GND . . . . –0.3 V to VDD + 0.3 V
Total AIN/REFIN Current (Indefinite) . . . . . . . . . . . . . 30 mA
Digital Input Voltage to GND . . . . . . . –0.3 V to VDD + 0.3 V
Digital Output Voltage to GND . . . . . –0.3 V to VDD + 0.3 V
Operating Temperature Range . . . . . . . . . . . –40∞C to +85∞C
Storage Temperature Range . . . . . . . . . . . . –65∞C to +150∞C
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . 150∞C
JC Thermal Impedance . . . . . . . . . . . . . . . . . . . . . . 14∞C/W
Lead Temperature, Soldering
Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . . . . 215∞C
Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220∞C
*Stresses above those listed under Absolute Maximum Ratings may cause per-
manent damage to the device. This is a stress rating only; functional operation of
the device at these or any other conditions above those listed in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although the
AD7783 features proprietary ESD protection circuitry, permanent damage may occur on devices
subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended
to avoid performance degradation or loss of functionality.
REV. C
–5–
AD7783
PIN CONFIGURATION
XTAL1
REFIN(+)
REFIN(–)
AIN(+)
1
2
3
4
5
6
7
8
16
15
14
XTAL2
V
DD
GND
13 MODE
12 DOUT/RDY
11 CS
AD7783
TOP VIEW
AIN(–)
(Not to Scale)
IOUT1
10 SCLK
IOUT2
IPIN
9
RANGE
PIN FUNCTION DESCRIPTIONS
Pin No. Mnemonic
Function
1
2
XTAL1
Input to the 32.768 kHz Crystal Oscillator Inverter.
REFIN(+)
Positive Reference Input. REFIN(+) can lie anywhere between VDD and GND + 1 V. The nominal refer-
ence voltage (REFIN(+) – REFIN(–)) is 2.5 V, but the part functions with a reference from 1 V to VDD
.
3
4
5
6
REFIN(–)
AIN(+)
AIN(–)
Negative Reference Input. This reference input can lie anywhere between GND and VDD – 1 V.
Analog Input. AIN(+) is the positive terminal of the fully differential analog input pair AIN(+)/AIN(–).
Analog Input. AIN(–) is the negative terminal of the fully differential analog input pair AIN(+)/AIN(–).
IOUT1
Output from Internal 200 mA Excitation Current Source. Either current source IEXC1 or IEXC2 can be
switched to this output using hardware control pin IPIN.
7
8
IOUT2
IPIN
Output from Internal 200 mA Excitation Current Source. Either current source IEXC1 or IEXC2 can be
switched to this output using hardware control pin IPIN.
Logic Input that Selects the Routing of the On-Chip Current Sources. When IPIN is tied to GND, IEXC1
is routed to IOUT1 and IEXC2 is routed to IOUT2. When IPIN is tied to VDD, IEXC1 is routed to
IOUT2 and IEXC2 is routed to IOUT1.
9
RANGE
SCLK
Logic Input that Configures the Input Range on the Internal PGA. With RANGE = 0, the full-scale input
range is ±160 mV; the full-scale input range equals ±2.56 V when RANGE = 1 for a 2.5 V reference.
10
Serial Clock Input/Output for Data Transfers from the ADC. When the device is operated in master mode,
SCLK is an output with one SCLK period equal to one XTAL period. In slave mode, SCLK is generated
by an external source. In slave mode, all the data can be transmitted on a continuous train of pulses. Alter-
natively, it can be a noncontinuous clock with the information being transmitted from the AD7783 in
smaller batches of data. SCLK is Schmitt triggered (slave mode), making the interface suitable for opto-
isolated applications.
11
12
CS
Chip Select Input. CS is an active low logic input used to select the AD7783. When CS is low, the PLL
establishes lock and allows the AD7783 to initiate a conversion. When CS is high, the conversion is aborted,
DOUT and SCLK are three-stated, the AD7783 enters standby mode, and any conversion result in the
output shift register is lost.
DOUT/RDY Serial Data Output/Data Ready Output. DOUT/RDY serves a dual purpose in this interface. When a conver-
sion is initiated, DOUT/RDY goes high and remains high until the conversion is complete. DOUT/RDY will
then return low to indicate that valid data is available to be read from the device. In slave mode, this acts as
an interrupt to the processor, indicating that valid data is available. If data is not read after a conversion,
DOUT/RDY will go high before the next update occurs. In master mode, DOUT/RDY goes low for at
least half an SCLK cycle before the device produces SCLKs. When SCLK becomes active, data is output
on the DOUT/RDY pin. Data is output on the falling SCLK edge and is valid on the rising edge.
13
MODE
The MODE pin selects master or slave mode of operation. When MODE = 0, the AD7783 operates in
master mode; the AD7783 is configured for slave mode when MODE = 1.
14
15
16
GND
VDD
Ground Reference Point for the AD7783.
Supply Voltage, 3 V or 5 V Nominal.
XTAL2
Output from the 32.768 kHz Crystal Oscillator Inverter.
–6–
REV. C
Typical Performance Characteristics–AD7783
3.0
9
8
7
6
5
4
3
2
؎2.56V RANGE
2.5
2.0
V
= 5V
DD
V
= 2.5V
= 25؇C
REF
1.5
1.0
0.5
0
T
A
؎160mV RANGE
1
0
1.0
1.5
2.0
2.5
3.0
(V)
3.5
4.0
4.5
5.0
V
REF
TPC 1. Noise Distribution Histogram
TPC 2. RMS Noise vs. Reference Input
ADC CIRCUIT INFORMATION
Overview
The output rate of the AD7783 (fADC) equals
fADC = 32.768 ¥ 103 / 69 ¥ 8 ¥ 3
The AD7783 incorporates a S-D ADC channel, on-chip pro-
grammable gain amplifier, and on-chip digital filtering intended
for the measurement of wide dynamic range, low frequency
signals such as those in weigh-scale, strain gage, pressure trans-
ducer, or temperature measurement applications.
(
)
while the settling time equals
Ê
Ë
ˆ
2
tSETTLE
=
= 2 ¥ tADC
Á
˜
¯
This ADC input is buffered and can be programmed to have an
input voltage range of ±160 mV or ±2.56 V. The input channel
is configured as a fully differential input. Buffering the input
channel means that the part can accommodate significant source
impedances on the analog input and that R, C filtering (for
noise rejection or RFI reduction) can be placed on the analog
input if required. The device requires an external reference of
2.5 V nominal. Figure 3 shows the basic connections required
to operate the part.
f
ADC
Normal-mode rejection is the major function of the digital filter
on the AD7783. Simultaneous 50 Hz and 60 Hz rejection of
better than 60 dB is achieved as notches are placed at both 50 Hz
and 60 Hz. Figure 4 shows the filter rejection.
0
–20
POWER
SUPPLY
–40
10F
0.1F
–60
–80
IN+
IN–
–100
–120
–140
–160
V
DD
AD7783
OUT+
AIN(+)
AIN(–)
OUT–
CS
CONTROLLER
DOUT/RDY
IOUT1
IOUT2
SCLK
10k⍀
6k⍀
0
10
20
30
40
50
60
70
80
90
100
XTAL1
XTAL2
FREQUENCY (Hz)
32.768kHz
CRYSTAL
REFIN(+)
REFIN(–)
OUTPUT DATA RATE = 19.8Hz
INPUT BANDWIDTH = 4.74Hz
50Hz REJECTION = –66dB, 50Hz ؎1Hz REJECTION = –60dB
60Hz REJECTION = –117dB, 60Hz ؎1Hz REJECTION = –94dB
GND
Figure 4. Filter Profile (Filter Notches at Both
50 Hz and 60 Hz)
Figure 3. Basic Connection Diagram
REV. C
–7–
AD7783
NOISE PERFORMANCE
MASTER MODE (MODE = 0)
Table I shows the output rms noise and output peak-to-peak
resolution in bits (rounded to the nearest 0.5 LSB) for the two
input voltage ranges. The numbers are typical and are generated
at a differential input voltage of 0 V. The peak-to-peak reso-
lution figures represent the resolution for which there will be
no code flicker within a six-sigma limit. The output noise comes
from two sources. The first is the electrical noise in the semi-
conductor devices (device noise) used in the implementation of
the modulator. Secondly, when the analog input is converted
into the digital domain, quantization noise is added. The device
noise is at a low level and is independent of frequency. The
quantization noise starts at an even lower level but rises rapidly
with increasing frequency to become the dominant noise source.
In this mode, SCLK is provided by the AD7783. With CS low,
SCLK becomes active when a conversion is complete and gener-
ates 24 falling and rising edges. The DOUT/RDY pin, which is
normally high, goes low to indicate that a conversion is complete.
Data is output on the DOUT/RDY pin following the SCLK
falling edge and is valid on the SCLK rising edge. When the
24-bit word has been output, SCLK idles high until the next
conversion is complete. DOUT/RDY returns high and will remain
high until another conversion is available. It then operates as a
RDY signal again. The part will continue to convert until CS is
taken high. SCLK and DOUT/RDY are three-stated when CS is
taken high.
SLAVE MODE (MODE = 1)
Table I. Typical Output RMS Noise and
Peak-to-Peak Resolution vs. Input Range
In slave mode, the SCLK is generated externally. SCLK must
idle high between data transfers. With CS low, DOUT/RDY
goes low when a conversion is complete. Twenty-four SCLK
pulses are needed to transfer the digital word from the AD7783.
Twenty-four consecutive pulses can be generated or, alterna-
tively, the data transfer can be split into batches. This is useful
when interfacing to a microcontroller that uses 8-bit transfers.
Data is output following the SCLK falling edge and is valid on
the SCLK rising edge.
Input Range
±160 mV
±2.56 V
Noise (mV)
Peak-to-Peak Resolution (Bits)
0.65
16.5
2.30
18.5
DIGITAL INTERFACE
CIRCUIT DESCRIPTION
Analog Input Channel
The AD7783’s serial interface consists of four signals: CS,
SCLK, DOUT/RDY, and MODE. The MODE pin is used to
select the master/slave mode of operation. When the part is
configured as a master, SCLK is an output; SCLK is an input
when slave mode is selected. Data transfers take place with
respect to this SCLK signal. The DOUT/RDY line is used
for accessing data from the data register. This pin also functions
as a RDY line. When a conversion is complete, DOUT/RDY
goes low to indicate that data is ready to be read from the
AD7783’s data register. It is reset high when a read operation
from the data register is complete. It also goes high prior to
the updating of the output register to indicate when not to
read from the device to ensure that a data read is not attempted
while the register is being updated. The digital conversion is
also output on this pin.
The ADC has one fully differential input channel. It feeds into a
high impedance input stage of the buffer amplifier. As a result,
the ADC input can handle significant source impedances and is
tailored for direct connection to external resistive-type sensors,
such as strain gages or resistance temperature detectors (RTDs).
The absolute input voltage range on the ADC input is restricted
to a range between GND + 100 mV and VDD – 100 mV. Care
must be taken in setting up the common-mode voltage and input
voltage range so that these limits are not exceeded; otherwise,
there will be a degradation in linearity and noise performance.
Programmable Gain Amplifier
The output from the buffer on the ADC is applied to the input of
the on-chip programmable gain amplifier (PGA). The PGA gain
range is programmed via the RANGE pin. With an external 2.5 V
reference applied, the PGA can be programmed to have a bipolar
range of ±160 mV (RANGE = 0) or ±2.56 V (RANGE = 1).
These are the ranges that should appear at the input to the
on-chip PGA.
CS is used to select the device and to place the device in standby
mode. When CS is taken low, the AD7783 is powered up, the
PLL locks, and the device initiates a conversion. The device will
continue to convert until CS is taken high. When CS is taken
high, the AD7783 is placed in standby mode, minimizing the
current consumption. The conversion is aborted, DOUT and
SCLK are three-stated, and the result in the data register is lost.
Bipolar Configuration/Output Coding
The analog input on the AD7783 accepts bipolar input voltage
ranges. Signals on the AIN(+) input of the ADC are referenced
Figure 2 shows the timing diagram for interfacing to the AD7783
with CS used to decode the part.
–8–
REV. C
AD7783
to the voltage on the AIN(–) input. For example, if AIN(–) is
2.5 V and the AD7783 is configured for an analog input range
of ±160 mV, the analog input range on the AIN(+) input is
2.34 V to 2.66 V (i.e., 2.5 V ± 0.16 V).
Deriving the reference input voltage across an external resistor
will mean that the reference input sees a significant external
source impedance. External decoupling on the REFIN pins
would not be recommended in this type of circuit configuration.
The coding is offset binary with a negative full-scale voltage
resulting in a code of 000 . . . 000, a zero differential voltage
resulting in a code of 100 . . . 000, and a positive full-scale
voltage resulting in a code of 111 . . . 111. The output code for
any analog input voltage can be represented as follows:
Grounding and Layout
Since the analog inputs and reference inputs on the ADC are
differential, most of the voltages in the analog modulator are
common-mode voltages. The excellent common-mode rejection
of the part will remove common-mode noise on these inputs.
The digital filter will provide rejection of broadband noise on
the power supply, except at integer multiples of the modulator
sampling frequency. The digital filter also removes noise from
the analog and reference inputs, provided these noise sources do
not saturate the analog modulator. As a result, the AD7783 is
more immune to noise interference than a conventional high
resolution converter. However, because the resolution of the
AD7783 is so high, and the noise levels from the AD7783 are so
low, care must be taken with regard to grounding and layout.
The printed circuit board that houses the AD7783 should be
designed such that the analog and digital sections are separated
and confined to certain areas of the board. A minimum etch
technique is generally best for ground planes as it gives the best
shielding.
Code = 2N -1
¥
AIN ¥ GAIN / 1.024 ¥V
+ 1
(
)
(
)
[
]
REF
where AIN is the analog input voltage, GAIN is the PGA gain,
i.e., 1 on the ±2.56 V range and 16 on the ±160 mV range,
and N = 24.
Excitation Currents
The AD7783 also contains two matched 200 mA constant cur-
rent sources. Both source current from VDD that is directed to
either the IOUT1 or IOUT2 pins of the device depending on
the polarity of the IPIN pin. These current sources can be used
to excite external resistive bridge or RTD sensors.
Crystal Oscillator
The AD7783 is intended for use with a 32.768 kHz watch crys-
tal. A PLL internally locks onto a multiple of this frequency to
provide a stable 4.194304 MHz clock for the ADC. The modu-
lator sample rate is the same as the crystal oscillator frequency.
The start-up time associated with 32.768 kHz crystals is typically
300 ms. In some cases, it will be necessary to connect capacitors
on the crystal to ensure that it does not oscillate at overtones of
its fundamental operating frequency. The values of capacitors will
vary depending on the manufacturer’s specifications.
It is recommended that the AD7783’s GND pin be tied to the
AGND plane of the system. In any layout, it is important that
the user keep in mind the flow of currents in the system, ensur-
ing that the return paths for all currents are as close as possible
to the paths the currents took to reach their destinations. Avoid
forcing digital currents to flow through the AGND sections of
the layout.
The AD7783’s ground plane should be allowed to run under
the AD7783 to prevent noise coupling. The power supply lines
to the AD7783 should use as wide a trace as possible to provide
low impedance paths and reduce the effects of glitches on the
power supply line. Fast switching signals like clocks should be
shielded with digital ground to avoid radiating noise to other
sections of the board, and clock signals should never be run
near the analog inputs. Avoid crossover of digital and analog
signals. Traces on opposite sides of the board should run at
right angles to each other. This will reduce the effects of
feedthrough through the board. A microstrip technique is by far
the best but is not always possible with a double-sided board. In
this technique, the component side of the board is dedicated to
ground planes while signals are placed on the solder side.
Reference Input
The AD7783 has a fully differential reference input capability
for the channel. The common-mode range for differential inputs
is from GND to VDD. The reference input is unbuffered, and
therefore excessive R-C source impedances will introduce gain
errors. The reference voltage REFIN (REFIN(+) – REFIN(–))
is 2.5 V nominal for specified operation, but the AD7783 is
functional with reference voltages from 1 V to VDD. In applica-
tions where the excitation (voltage or current) for the transducer
on the analog input also drives the reference voltage for the part,
the effect of the low frequency noise in the excitation source will
be removed as the application is ratiometric. If the AD7783 is
used in a nonratiometric application, a low noise reference should
be used. Recommended reference voltage sources for the AD7783
include the AD780, REF43, and REF192. It should also be noted
that the reference inputs provide a high impedance, dynamic load.
Because the input impedance of each reference input is dynamic,
resistor/capacitor combinations on these inputs can cause dc gain
errors, depending on the output impedance of the source that is
driving the reference inputs. Recommended reference voltage
sources (e.g., AD780) will typically have low output impedances
and are, therefore, tolerant to having decoupling capacitors
on the REFIN(+) without introducing gain errors in the system.
Good decoupling is important when using high resolution ADCs.
VDD should be decoupled with 10 mF tantalum in parallel with
0.1 mF capacitors to GND. To achieve the best from these
decoupling components, they have to be placed as close as pos-
sible to the device, ideally right up against the device. All
logic chips should be decoupled with 0.1 mF ceramic capaci-
tors to DGND.
REV. C
–9–
AD7783
OUTLINE DIMENSIONS
5.10
5.00
4.90
16
9
8
4.50
4.40
4.30
6.40
BSC
1
PIN 1
1.20
MAX
0.15
0.05
0.20
0.09
0.75
0.60
0.45
8°
0°
0.30
0.19
0.65
BSC
SEATING
PLANE
COPLANARITY
0.10
COMPLIANT TO JEDEC STANDARDS MO-153-AB
Figure 1. 16-Lead Thin Shrink Small Outline Package [TSSOP]
(RU-16)
Dimensions shown in millimeters
ORDERING GUIDE
Model1
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
Package Option
RU-16
RU-16
RU-16
RU-16
AD7783BRU
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
Evaluation Board
AD7783BRU-REEL
AD7783BRU-REEL7
AD7783BRUZ
AD7783BRUZ-REEL7
EVAL-AD7783EBZ
RU-16
1 Z = RoHS Compliant Part.
REVISION HISTORY
10/11—Rev. B to Rev. C
Changes to Figure 2...........................................................................5
Changes to Ordering Guide...........................................................10
8/04—Data Sheet Changed from Rev. A to Rev. B.
Change to Features............................................................................1
Changes to Ordering Guide.............................................................5
4/03—Data Sheet Changed from Rev. 0 to Rev. A.
Change to Specifications ..................................................................2
Updated Outline Dimensions........................................................10
Rev. C | Page 10 of 12
AD7783
NOTES
Rev. C | Page 11 of 12
AD7783
NOTES
©2002–2011 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D02702-0-10/11(C)
Rev. C | Page 12 of 12
相关型号：
AD7785BRUZ-REEL
3-Channel, Low Noise, Low Power, 20-Bit ⒉-ツ ADC with On-Chip In-Amp and Reference
ADI
©2020 ICPDF网 联系我们和版权申明