AD780CR-REEL7 [ADI]
2.5 V/3.0 V High Precision Reference; 2.5 V / 3.0 V高精密基准型号: | AD780CR-REEL7 |
厂家: | ADI |
描述: | 2.5 V/3.0 V High Precision Reference |
文件: | 总10页 (文件大小:179K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
2.5 V/3.0 V
High Precision Reference
a
AD780
FUNCTIONAL BLOCK DIAGRAM
FEATURES
Pin-Programmable 2.5 V or 3.0 V Output
Ultralow Drift: 3 ppm/ꢀC max
High Accuracy: 2.5 V or 3.0 V ꢁ 1 mV max
+VIN
NC
2
7
Low Noise: 100 nV/√Hz
Noise Reduction Capability
AD780
Low Quiescent Current: 1 mA max
Output Trim Capability
R10
R11
Plug-In Upgrade for Present References
Temperature Output Pin
Series or Shunt Mode Operation (ꢁ2.5 V, ꢁ3.0 V)
1
NC
VOUT
6
5
R13
Q6
Q7
TRIM
R5
R4
R16
R14
R15
PRODUCT DESCRIPTION
3
TEMP
The AD780 is an ultrahigh precision bandgap reference voltage
which provides a 2.5 V or 3.0 V output from inputs between
4.0 V and 36 V. Low initial error and temperature drift com-
bined with low output noise and the ability to drive any value of
capacitance make the AD780 the ideal choice for enhancing the
performance of high resolution ADCs and DACs and for any
general purpose precision reference application. A unique low
headroom design facilitates a 3.0 V output from a 5.0 V 10%
input, providing a 20% boost to the dynamic range of an ADC,
over performance with existing 2.5 V references.
4
8
O/P SELECT
2.5V - NC
GND
NC = NO CONNECT
3.0V - GND
PRODUCT HIGHLIGHTS
1. The AD780 provides a pin-programmable 2.5 V or 3.0 V
output from a 4 V to 36 V input.
The AD780 can be used to source or sink up to 10 mA and can
be used in series or shunt mode, thus allowing positive or nega-
tive output voltages without external components. This makes it
suitable for virtually any high performance reference application.
Unlike some competing references, the AD780 has no “region
of possible instability.” The part is stable under all load condi-
tions when a 1 µF bypass capacitor is used on the supply.
2. Laser trimming of both initial accuracy and temperature
coefficients results in low errors over temperature without the
use of external components. The AD780BN has a maximum
variation of 0.9 mV from –40°C to +85°C.
3. For applications requiring even higher accuracy, an optional
fine-trim connection is provided.
4. The AD780 noise is extremely low, typically 4 µV p-p from
0.1 Hz to 10 Hz and a wideband spectral noise density of
typically 100 nV/√Hz. This can be further reduced if desired,
by simply using two external capacitors.
A temperature output pin is provided on the AD780. This pro-
vides an output voltage that varies linearly with temperature, al-
lowing the AD780 to be configured as a temperature transducer
while providing a stable 2.5 V or 3.0 V output.
5. The temperature output pin enables the AD780 to be config-
ured as a temperature transducer while providing a stable
output reference voltage.
The AD780 is a pin-compatible performance upgrade for the
LT1019(A)–2.5 and the AD680. The latter is targeted toward
low power applications.
The AD780 is available in three grades in plastic DIP, SOIC,
and cerdip packages. The AD780AN, AD780AR, AD780BN,
AD780BR, and AD780CR are specified for operation from –40°C
to +85°C.
REV. B
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
Fax: 781/326-8703
World Wide Web Site: http://www.analog.com
© Analog Devices, Inc., 2000
(TA = +25ꢀC, VIN = +5 V unless otherwise noted)
AD780–SPECIFICATIONS
AD780AN/AR
AD780CR
Typ
AD780BN/BR
Parameter
Min
Typ
Max
Min
Max
Min
Typ
Max
Unit
OUTPUT VOLTAGE
2.5 V Out
3.0 V Out
2.495
2.995
2.505
3.005
2.4985
2.9950
2.5015 2.499
3.0050 2.999
2.501
3.001
Volts
Volts
OUTPUT VOLTAGE DRIFT1
–40°C to +85°C
–55°C to +125°C
7
20
7
20
3
ppm/°C
ppm/°C
LINE REGULATION
2.5 V Output, 4 V ≤ +VIN ≤ 36 V
T
MIN to TMAX
10
10
*
*
*
*
µV/V
µV/V
3.0 V Output, 4.5 V ≤ +VIN ≤ 36 V
TMIN to TMAX
LOAD REGULATION, SERIES MODE
Sourcing 0 < IOUT < 10 mA
TMIN to TMAX
Sinking –10 < IOUT < 0 mA
–40°C to +85°C
50
75
75
75
150
*
*
*
*
*
*
*
*
*
*
µV/mA
µV/mA
µV/mA
µV/mA
µV/mA
–55°C to +125°C
LOAD REGULATION, SHUNT MODE
I < ISHUNT < 10 mA
75
*
*
µV/mA
QUIESCENT CURRENT, 2.5 V SERIES MODE2
–40°C to +85°C
–55°C to +125°C
0.75
0.8
1.0
1.3
*
*
*
*
*
*
*
*
mA
mA
MINIMUM SHUNT CURRENT
0.7
1.0
*
*
*
*
mA
OUTPUT NOISE
0.1 Hz to 10 Hz
Spectral Density, 100 Hz
4
100
*
*
*
*
*
*
*
*
µV p-p
nV/√Hz
LONG TERM STABILITY3
20
*
*
ppm/
1000 Hr
TRIM RANGE
4.0
*
*
*
%
TEMPERATURE PIN
Voltage Output @ 25°C
Temperature Sensitivity
Output Resistance
500
560
1.9
3
620
*
*
*
*
*
*
*
*
*
mV
mV/°C
kΩ
SHORT CIRCUIT CURRENT TO GROUND
30
*
*
mA
TEMPERATURE RANGE
Specified Performance (A, B, C)
Operating Performance (A, B, C)4
Specified Performance (S)
–40
–55
–55
–55
+85
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
°C
°C
°C
°C
+125
+125
+125
Operating Performance (S)
NOTES
1Maximum output voltage drift is guaranteed for all packages.
23.0 V mode typically adds 100 µA to the quiescent current. Also, Iq increases by 2 µA/V above an input voltage of 5 V.
3The long term stability specification is noncumulative. The drift in subsequent 1000 hr. periods is significantly lower than in the first 1000 hr. period.
4The operating temperature range is defined as the temperature extremes at which the device will still function. Parts may deviate from their specified performance
outside their specified temperature range.
*Same as AD780AN/AR specification.
Specifications subject to change without notice.
–2–
REV. B
AD780
ABSOLUTE MAXIMUM RATINGS*
DIE LAYOUT
VIN to Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 V
Trim Pin to Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 V
Temp Pin to Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 V
Power Dissipation (25°C) . . . . . . . . . . . . . . . . . . . . . . 500 mW
Storage Temperature . . . . . . . . . . . . . . . . . . . –65°C to +150°C
Lead Temperature (Soldering, 10 sec) . . . . . . . . . . . . . 300°C
Output Protection: Output safe for indefinite short to ground
and momentary short to VIN.
ESD Classification . . . . . . . . . . . . . . . . . . . . . Class 1 (1000 V)
*Stresses above those listed under Absolute Maximum Ratings may cause perma-
nent damage to the device. This is a stress rating only; functional operation of the
device at these or any conditions above those indicated in the operational specifi-
cation is not implied. Exposure to absolute maximum specifications for extended
periods may affect device reliability.
PIN CONFIGURATION
8-Lead Plastic DIP, SOIC and Cerdip Packages
NOTES
Both VOUT pads should be connected to the output
Die Thickness: The standard thickness of Analog Devices Bipolar dice is
24 mils 2 mils.
Die Dimensions: The dimensions given have a tolerance of 2 mils.
Backing: The standard backside surface is silicon (not plated). Analog Devices
does not recommend gold-backed dice for most applications.
Edges: A diamond saw is used to separate wafers into dice thus providing per-
pendicular edges half-way through the die.
2.5/3.0V SELECT
(NC OR GND)
1
2
3
4
NC
8
7
6
5
+V
IN
NC
AD780
TOP VIEW
(Not to Scale)
TEMP
V
OUT
GND
TRIM
NC = NO CONNECT
In contrast to scribed dice, this technique provides a more uniform die shape
and size. The perpendicular edges facilitate handling (such as tweezer pick-up)
while the uniform shape and size simplifies substrate design and die attach.
Top Surface: The standard top surface of the die is covered by a layer of
glassivation. All areas are covered except bonding pads and scribe lines.
Surface Metalization: The metalization to Analog Devices bipolar dice is alu-
minum. Minimum thickness is 10,000Å.
Bonding Pads: All bonding pads have a minimum size of 4.0 mils by 6.0 mils.
The passivation windows have a 3.6 mils by 5.6 mils minimum size.
ORDERING GUIDE
Initial
Error
Temperature
Range
Temperature
Coefficient
Package
Options
Model
AD780AN
AD780AR
AD780AR-REEL7
AD780BN
Ϯ5.0 mV
Ϯ5.0 mV
Ϯ5.0 mV
Ϯ1.0 mV
Ϯ1.0 mV
Ϯ1.0 mV
Ϯ1.0 mV
Ϯ1.5 mV
Ϯ1.5 mV
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
7 ppm/°C
7 ppm/°C
7 ppm/°C
3 ppm/°C
3 ppm/°C
3 ppm/°C
3 ppm/°C
7 ppm/°C
7 ppm/°C
Plastic Dip
SOIC
SOIC
Plastic Dip
SOIC
SOIC
SOIC
SOIC
SOIC
AD780BR
AD780BR-REEL
AD780BR-REEL7
AD780CR
AD780CR-REEL7
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the AD780 features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high-energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
REV. B
–3–
AD780
THEORY OF OPERATION
APPLYING THE AD780
Bandgap references are the high performance solution for low
supply voltage and low power voltage reference applications. In
this technique a voltage with a positive temperature coefficient is
combined with the negative coefficient of a transistor’s Vbe to
produce a constant bandgap voltage.
The AD780 can be used without any external components to
achieve specified performance. If power is supplied to Pin 2 and
Pin 4 is grounded, Pin 6 provides a 2.5 V or 3.0 V output de-
pending on whether Pin 8 is left unconnected or grounded.
A bypass capacitor of 1 µF (VIN to GND) should be used if the
load capacitance in the application is expected to be greater
than 1 nF. The AD780 in 2.5 V mode typically draws 700 µA of
Iq at 5 V. This increases by ~2 µA/V up to 36 V.
In the AD780, the bandgap cell contains two npn transistors
(Q6 and Q7) which differ in emitter area by 12ϫ. The differ-
ence in their Vbe’s produces a PTAT current in R5. This in
turn produces a PTAT voltage across R4, which when com-
bined with the Vbe of Q7, produces a voltage Vbg that does not
vary with temperature. Precision laser trimming of the resistors
and other patented circuit techniques are used to further enhance
the drift performance.
NC
+V
IN
V
OUT
NC
AD780
1ꢂF
R
+V
NULL
IN
NC
R POT.
TRIM
TEMP
GND
AD780
O/P SELECT
2.5V – NC
3.0V – GND
R11
R10
NC
V
OUT
NC = NO CONNECT
Figure 2. Optional Fine Trim Circuit
R13
Initial error can be nulled using a single 25 kΩ potentiometer
connected between VOUT, Trim and GND. This is a coarse trim
with an adjustment range of 4% and is only included here for
compatibility purposes with other references. A fine trim can be
implemented by inserting a large value resistor (e.g. 1–5 MΩ) in
series with the wiper of the potentiometer. See Figure 2 above.
The trim range, expressed as a fraction of the output, is simply
greater than or equal to 2.1 kΩ/RNULL for either the 2.5 V or
3.0 V mode.
Q6
Q7
TRIM
R16
R5
R4
R14
R15
TEMP
GND
O/P SELECT
2.5V - NC
3.0V - GND
The external null resistor affects the overall temperature coeffi-
cient by a factor equal to the percentage of VOUT nulled.
NC = NO CONNECT
Figure 1. Schematic Diagram
For example a 1 mV (.03%) shift in the output caused by the
trim circuit, with a 100 ppm/°C null resistor will add less than
0.06 ppm/°C to the output drift (0.03% ϫ 200 ppm/°C, since
the resistors internal to the AD780 also have temperature coeffi-
cients of less than 100 ppm/°C).
The output voltage of the AD780 is determined by the configu-
ration of resistors R13, R14 and R15 in the amplifier’s feedback
loop. This sets the output to either 2.5 V or 3.0 V depending on
whether R15 (Pin 8) is grounded or not connected.
A unique feature of the AD780 is the low headroom design of
the high gain amplifier which produces a precision 3 V output
from an input voltage as low as 4.5 V (or 2.5 V from a 4.0 V
input). The amplifier design also allows the part to work with
VIN = VOUT when current is forced into the output terminal.
This allows the AD780 to work as a two terminal shunt regula-
tor providing a –2.5 V or –3.0 V reference voltage output with-
out external components.
The PTAT voltage is also used to provide the user with a ther-
mometer output voltage (at Pin 3) which increases at a rate of
approximately 2 mV/°C.
The AD780’s NC Pin 7 is a 20 kΩ resistor to V+ which is used
solely for production test purposes. Users who are currently us-
ing the LT1019 self-heater pin (Pin 7) must take into account
the different load on the heater supply.
–4–
REV. B
AD780
NOISE PERFORMANCE
NOISE COMPARISON
The impressive noise performance of the AD780 can be further
improved if desired by the addition of two capacitors: a load ca-
pacitor C1 between the output and ground, and a compensation
capacitor C2 between the TEMP pin and ground. Suitable val-
ues are shown in Figure 3.
The wideband noise performance of the AD780 can also be ex-
pressed in ppm. The typical performance with C1, C2 is
0.6 ppm and without external capacitors is 1.2 ppm.
This performance is respectively 7ϫ and 3ϫ lower than the
specified performance of the LT1019.
100
10
1
NO AMPLIFIER
20ꢂV
10ms
100
90
10
0%
10Hz TO 10kHz
0.1
Figure 6. Reduced Noise Performance with C1 = 100 µF,
C2 = 100 nF
0.1
1
10
100
LOAD CAPACITOR, C1 – ꢂF
TEMPERATURE PERFORMANCE
Figure 3. Compensation and Load Capacitor Combinations
The AD780 provides superior performance over temperature by
means of a combination of patented circuit design techniques,
precision thin film resistors and drift trimming. Temperature
performance is specified in terms of ppm/°C, but because of
nonlinearity in the temperature characteristic, the Box-Test
method is used to test and specify the part. The nonlinearity
takes the form of the characteristic S-shaped curve shown in
Figure 7. The Box-Test method forms a rectangular box around
this curve, enclosing the maximum and minimum output volt-
ages over the specified temperature range. The specified drift is
equal to the slope of the diagonal of this box.
C1 and C2 also improve the settling performance of the AD780
when subjected to load transients. The improvement in noise
performance is shown in Figures 4, 5 and 6 following.
AMPLIFIER GAIN = 100
NO AMPLIFIER
10ms
100ꢂV
1s
20ꢂV
100
100
90
90
10
10
0%
0%
2.0
1.6
1.2
0.8
0.4
0
0.1 TO 10Hz
10Hz TO 10kHz
Figure 4. Stand-Alone Noise Performance
NC
+V
IN
V
OUT
NC
AD780
1ꢂF
–0.4
TRIM
C1
TEMP
GND
O/P SELECT
2.5V – NC
3.0V – GND
–0.8
C2
–60 –40 –20
20
40
60
80
100 120 140
0
TEMPERATURE –
ꢀC
Figure 7. Typical AD780BN Temperature Drift
NC = NO CONNECT
Figure 5. Noise Reduction Circuit
REV. B
–5–
AD780
TEMPERATURE OUTPUT PIN
TEMPERATURE TRANSDUCER CIRCUIT
The AD780 provides a “TEMP” output (Pin 3) that varies
linearly with temperature. This output can be used to monitor
changes in system ambient temperature and to initiate calibration
of the system if desired. The voltage VTEMP is 560 mV at 25°C,
and the temperature coefficient is approximately 2 mV/°C.
Figure 8 shows the typical VTEMP characteristic curve over tem-
perature taken at the output of the op amp with a noninverting
gain of five.
The circuit shown in Figure 9 is a temperature transducer which
a amplifies the TEMP output voltage by a gain of a little over 5
to provide a wider full scale output range. The trimpot can be
used to adjust the output so it varies exactly by 10 mV/°C.
To minimize resistance changes with temperature, resistors with
low temperature coefficients, such as metal film resistors should
be used.
+5V
4.25
CIRCUIT CALIBRATED AT 25
REFER TO FIGURE 9
ꢀ
C
4.00
3.75
3.50
3.25
3.00
2.75
2.50
2.25
2.00
V
IN
1ꢂF
TEMP
10mV/ꢀC
AD820
10mV PER ꢀC
AD780
R
F
6.04kꢃ (1%)
1.27kꢃ (1%)
GND
R
B
–75
–50
–25
0
25
50
75
100
125
150
R
BP
200ꢃ
TEMPERATURE –
ꢀC
Figure 8. Temperature Pin Transfer Characteristic
Since the TEMP voltage is acquired from the bandgap core cir-
cuit, current pulled from this pin will have a significant effect on
Figure 9. Differential Temperature Transducer
SUPPLY CURRENT OVER TEMPERATURE
V
OUT. Care must be taken to buffer the TEMP output with a
suitable op amp, e.g., an OP07, AD820 or AD711 (all of which
would result in less than a 100 µV change in VOUT). The rela-
tionship between ITEMP and VOUT is as follows:
The AD780’s quiescent current will vary slightly over tempera-
ture and input supply range. The test limit is 1 mA over the in-
dustrial and 1.3 mA over the military temperature range.
Typical performance with input voltage and temperature varia-
tion is shown in Figure 10 following.
∆VOUT = 5.8 mV/µA × ITEMP (2.5 V range)
or
∆VOUT = 6.9 mV/µA × ITEMP (3.0 V range)
0.85
Notice how sensitive the current dependent factor on VOUT is. A
large amount of current, even in tens of microamp, drawn from
TEMP pin can cause VOUT and TEMP Output to fail.
–55ꢀC
0.80
0.75
0.70
0.65
0.60
25ꢀC
The choice of C1 and C2 was dictated primarily by the need for a
relatively flat response that rolled off early in the high frequency
noise at the output. But there is considerable margin in the
choice of these capacitors. For example, the user can actually
put a huge C2 on the TEMP pin with none on the output pin.
However, one must either put very little or a lot of capacitance at
the TEMP pin. Intermediate values of capacitance can sometimes
cause oscillation. In any case, the user should follow the recom-
mendation in Figure 3.
125ꢀC
4
36
INPUT VOLTAGE – Volts
Figure 10. Typical Supply Current over Temperature
–6–
REV. B
AD780
TURN-ON TIME
I
The time required for the output voltage to reach its final value
within a specified error band is defined as the turn-on settling
time. The two major factors that affect this are the active circuit
settling time and the time for the thermal gradients on the chip
to stabilize. Typical settling performance is shown in Figure 11
following. The AD780 settles to within 0.1% of its final value
within 10 µs.
0mA
LOAD
10mA
V
(C = 0pF)
L
OUT
V
IN
5V
0V
10ꢂs/DIV
Figure 12b. Settling Under Transient Resistive Load
V
OUT
The dynamic load may be resistive and capacitive. For example
the load may be connected via a long capacitive cable. Figure 13
following shows the performance of the AD780 driving a
1000 pF, 0 mA to 10 mA load.
2.500V
2.499V
2.498V
+V
IN
10ꢂs/DIV
Figure 11. Turn-On Settling Time Performance
DYNAMIC PERFORMANCE
The output stage of the AD780 has been designed to provide
superior static and dynamic load regulation.
AD780
1ꢂF
V
OUT
C
L
1000pF
Figure 12 shows the performance of the AD780 while driving a
0 mA to 10 mA load.
249ꢃ
+V
IN
V
OUT
V
L
0V
Figure 13a. Capacitive Load Transient Response
Test Circuit
AD780
1ꢂF
V
OUT
I
0mA
LOAD
249ꢃ
10mA
V
OUT
V
L
V
OUT
(C = 1000pF)
0V
L
Figure 12a. Transient Resistive Load Test Circuit
10ꢂs/DIV
Figure 13b. Settling Under Dynamic Capacitive Load
REV. B
–7–
AD780
LINE REGULATION
The AD780 is also ideal for use with higher resolution convert-
ers such as the AD7710/AD7711/AD7712. (See Figure 16.)
While these parts are specified with a 2.5 V internal reference,
the AD780 in 3 V mode can be used to improve the absolute ac-
curacy, temperature stability and dynamic range. It is shown fol-
lowing with the two optional noise reduction capacitors.
Line regulation is a measure of the change in output voltage due
to a specified change in input voltage. It is intended to simulate
worst case unregulated supply conditions and is measured in
µV/V. Figure 14 shows typical performance with 4.0 V < VIN
15.0 V.
<
+5V
200
T = 25ꢀC
100
0
V
IN
1ꢂF
V
OUT
REFIN+
AD780
100ꢂF
AD7710
–100
–200
2.5/3.0V
SELECT
100nF
GND
REFIN–
4
10
15
INPUT VOLTAGE – Volts
Figure 14. Output Voltage Change vs. Input Voltage
Figure 16. Precision 2.5 V or 3.0 V Reference for the
AD7710 High Resolution, Sigma-Delta ADC
PRECISION REFERENCE FOR HIGH RESOLUTION
+5 V DATA CONVERTERS
The AD780 is ideally suited to be the reference for most +5 V
high resolution ADCs. The AD780 is stable under any capaci-
tive load, it has superior dynamic load performance, and the
3.0 V output provides the converter with maximum dynamic
range without requiring an additional and expensive buffer am-
plifier. One of the many ADCs that the AD780 is suited for is
the AD7884, a 16-bit, high speed sampling ADC. (See Figure
15.) This part previously needed a precision 5.0 V reference, re-
sistor divider and buffer amplifier to do this function.
+4.5 V REFERENCE FROM +5 V SUPPLY
Some +5 V high resolution ADCs can accommodate reference
voltages up to +4.5 V. The AD780 can be used to provide a
precision +4.5 V reference voltage from a +5 V supply using the
circuit shown following in Figure 17. This circuit will provide a
regulated +4.5 V output from a supply voltage as low as +4.7 V.
The high quality tantalum 10 µF capacitor in parallel with the
ceramic 0.1 µF capacitor and the 3.9 Ω resistor ensure a low
output impedance up to around 50 MHz.
+5V
V
SUPPLY
0.1ꢂF
1kꢃ
V
IN
2N2907
1ꢂF
V
+F
+S
V
REF
OP90
OUT
AD780
V
OUT
2.5kꢃ
AD780
10ꢂF
0.1ꢂF
V
REF
0.1ꢂF
3.9ꢃ
2.5/3.0V
SELECT
GND
AD7884
4kꢃ
0.01%
5kꢃ
0.01%
Figure 17. +4.5 V Reference from a Single +5 V Supply
Figure 15. Precision 3.0 V Reference for the AD7884
16-Bit, High Speed ADC
–8–
REV. B
AD780
NEGATIVE (–2.5 V OR –3.0 V) REFERENCE
A precise –2.5 V (or –3.0 V) reference capable of supplying up
to 100 mA to a load can be implemented with the AD780 in se-
ries mode using the bootstrap circuit following.
The AD780 can produce a negative output voltage in shunt
mode, simply by connecting the input and output to ground
connecting the AD780’s GND pin to a negative supply via a
bias resistor as shown in Figure 18.
+5V
V
IN
OUT
AD780
1kꢃ
+V
NC
CONNECT IF
–3V OUTPUT
DESIRED
IN
V
NC
OUT
+5V
OP07
–5V
AD780
TRIM
TEMP
–2.5V (I Յ 100mA)
L
O/P SELECT
2.5V – NC
3.0V – GND
2N3906
1ꢂF
GND
–5V
–2.5 V
OUT
V
– (V–)
OUT
NOTE:
R =
I
I
= LOAD CURRENT
MIN = MINIMUM SHUNT CURRENT
I
+ I MIN
L
L
S
S
1000pF
NC = NO CONNECT
V–
Figure 19. –2.5 V High Load Current Reference
Figure 18. Negative (–2.5 V) Shunt Mode Reference
REV. B
–9–
AD780
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
SOIC (R) Package
0.198 (5.00)
0.188 (4.75)
5
8
0.158 (4.00)
0.150 (3.80)
0.244 (6.200)
0.228 (5.80)
1
4
0.050
(1.27)
TYP
0.018 (0.46)
0.014 (0.36)
0.205 (5.20)
0.181 (4.60)
0.069 (1.75)
0.053 (1.35)
0.010 (0.25)
0.004 (0.10)
0.045 (1.15)
0.020 (0.50)
0.015 (0.38)
0.007 (0.18)
Plastic Mini-DIP (N) Package
8
5
0.280 (7.11)
0.240 (6.10)
PIN 1
1
4
0.325 (8.25)
0.300 (7.62)
0.430 (10.92)
0.348 (8.84)
0.060 (1.52)
0.015 (0.38)
0.195 (4.95)
0.115 (2.93)
0.210
(5.33)
MAX
0.130
(3.30)
MIN
0.160 (4.06)
0.115 (2.93)
0.015 (0.381)
0.008 (0.204)
SEATING
PLANE
0.100
(2.54)
BSC
0.070 (1.77)
0.045 (1.15)
0.022 (0.558)
0.014 (0.356)
Cerdip (Q) Package
0.005 (0.13) MIN
8
0.055 (1.4) MAX
5
0.310 (7.87)
0.220 (5.59)
4
1
0.070 (1.78)
0.030 (0.76)
0.320 (8.13)
0.290 (7.37)
0.405 (10.29) MAX
0.200
0.060 (1.52)
0.015 (0.38)
(5.08)
MAX
0.150
(3.81)
MIN
0.200 (5.08)
0.125 (3.18)
0.015 (0.38)
0.008 (0.20)
0°-15°
SEATING PLANE
0.023 (0.58)
0.014 (0.36)
0.100 (2.54)
BSC
–10–
REV. B
相关型号:
AD7810YN
1-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDIP8, 0.300 INCH, MINI, PLASTIC, DIP-8
ROCHESTER
AD7810YNZ
1-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDIP8, 0.300 INCH, MINI, PLASTIC, DIP-8
ROCHESTER
AD7810YR-REEL
IC 1-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO8, SOIC-8, Analog to Digital Converter
ADI
©2020 ICPDF网 联系我们和版权申明