AD7890BRZ-2REEL [ADI]
8-Channel, 12-Bit Serial Data Acquisition System;型号: | AD7890BRZ-2REEL |
厂家: | ADI |
描述: | 8-Channel, 12-Bit Serial Data Acquisition System |
文件: | 总29页 (文件大小:392K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LC2MOS 8-Channel, 12-Bit
Serial Data Acquisition System
AD7890
FUNCTIONAL BLOCK DIAGRAM
FEATURES
V
MUX SHA REF OUT/
Fast 12-bit ADC with 5.9 μs conversion time
Eight single-ended analog input channels
Selection of input ranges:
10 V for AD7890-10
0 V to 4.096 V for AD7890-4
0 V to 2.5 V for AD7890-2
Allows separate access to multiplexer and ADC
On-chip track/hold amplifier
DD
OUT IN
REF IN
SIGNAL
V
V
2kΩ
IN1
1
1
1
1
1
1
1
1
2.5V
SCALING
REFERENCE
SIGNAL
SCALING
IN2
V
V
V
V
V
V
SIGNAL
SCALING
IN3
C
EXT
SIGNAL
SCALING
IN4
MUX
SIGNAL
SCALING
On-chip reference
IN5
IN6
IN7
IN8
CONVST
High-speed, flexible, serial interface
Single supply, low-power operation (50 mW maximum)
Power-down mode (75 μW typ)
SIGNAL
SCALING
12-BIT
ADC
SIGNAL
SCALING
TRACK/HOLD
SIGNAL
SCALING
GENERAL DESCRIPTION
OUTPUT/CONTROL REGISTER
AD7890
The AD7890 is an 8-channel 12-bit data acquisition system. The
part contains an input multiplexer, an on-chip track/hold
amplifier, a high speed 12-bit ADC, a 2.5 V reference, and a
high speed, serial interface. The part operates from a single 5 V
supply and accepts an analog input range of 10 V (AD7890-10),
0 V to 4.096 V (AD7890-4), and 0 V to 2.5 V (AD7890-2).
CLOCK
AGND AGND DGND CLK
IN
SCLK TFS RFS DATA DATA SMODE
OUT IN
1
NO SCALING ON AD7890-2
Figure 1.
Power dissipation in normal mode is low at 30 mW typical and the
part can be placed in a standby (power-down) mode if it is not
required to perform conversions. The AD7890 is fabricated in
Analog Devices, Inc.’s Linear Compatible CMOS (LC2MOS)
process, a mixed technology process that combines precision
bipolar circuits with low power CMOS logic. The part is available
in a 24-lead, 0.3" wide, plastic or ceramic dual-in-line package or in
a 24-lead small outline package (SOIC_W).
The multiplexer on the part is independently accessible. This
allows the user to insert an antialiasing filter or signal
conditioning, if required, between the multiplexer and the
ADC. This means that one antialiasing filter can be used for all
eight channels. Connection of an external capacitor allows the
user to adjust the time given to the multiplexer settling to
include any external delays in the filter or signal conditioning
circuitry.
PRODUCT HIGHLIGHTS
Output data from the AD7890 is provided via a high speed
bidirectional serial interface port. The part contains an on-chip
control register, allowing control of channel selection,
conversion start, and power-down via the serial port. Versatile,
high speed logic ensures easy interfacing to serial ports on
microcontrollers and digital signal processors.
1. Complete 12-Bit Data Acquisition System-on-a-Chip.
The AD7890 is a complete monolithic ADC combining an
8-channel multiplexer, 12-bit ADC, 2.5 V reference, and a
track/hold amplifier on a single chip.
2. Separate Access to Multiplexer and ADC.
The AD7890 provides access to the output of the
multiplexer allowing one antialiasing filter for 8 channels—
a considerable savings over the 8 antialiasing filters required if
the multiplexer is internally connected to the ADC.
In addition to the traditional dc accuracy specifications such as
linearity, full-scale, and offset errors, the AD7890 is also
specified for dynamic performance parameters including
harmonic distortion and signal-to-noise ratio.
3. High Speed Serial Interface.
The part provides a high speed serial interface for easy
connection to serial ports of microcontrollers and DSP
processors.
Rev. C
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
©2006 Analog Devices, Inc. All rights reserved.
AD7890* PRODUCT PAGE QUICK LINKS
Last Content Update: 02/23/2017
COMPARABLE PARTS
View a parametric search of comparable parts.
DESIGN RESOURCES
• AD7890 Material Declaration
• PCN-PDN Information
• Quality And Reliability
• Symbols and Footprints
DOCUMENTATION
Application Notes
• AN-413: Evaluation Board for the AD7890, 12-Bit Serial,
Data Acquisition System
DISCUSSIONS
View all AD7890 EngineerZone Discussions.
Data Sheet
• AD7890: LC2MOS 8-Channel, 12-Bit Serial, Data
Acquisition System Data Sheet
SAMPLE AND BUY
Visit the product page to see pricing options.
• AD7890: Military Data Sheet
Product Highlight
• 8- to 18-Bit SAR ADCs ... From the Leader in High
Performance Analog
TECHNICAL SUPPORT
Submit a technical question or find your regional support
number.
REFERENCE MATERIALS
Technical Articles
DOCUMENT FEEDBACK
• MS-2210: Designing Power Supplies for High Speed ADC
Submit feedback for this data sheet.
This page is dynamically generated by Analog Devices, Inc., and inserted into this data sheet. A dynamic change to the content on this page will not
trigger a change to either the revision number or the content of the product data sheet. This dynamic page may be frequently modified.
AD7890
TABLE OF CONTENTS
Features .............................................................................................. 1
Serial Interface ................................................................................ 17
Self-Clocking Mode ................................................................... 17
External Clocking Mode ........................................................... 18
Simplifying the Interface........................................................... 19
Microprocessor/Microcontroller Interface................................. 20
AD7890 to 8051 Interface ......................................................... 20
AD7890 to 68HC11 Interface................................................... 20
AD7890 to ADSP-2101 Interface ............................................. 21
AD7890 to DSP56000 Interface ............................................... 21
AD7890 to TMS320C25/30 Interface...................................... 21
Antialiasing Filter....................................................................... 22
Performance .................................................................................... 23
Linearity....................................................................................... 23
Noise ............................................................................................ 23
Dynamic Performance............................................................... 24
Effective Number of Bits ........................................................... 24
Outline Dimensions....................................................................... 25
Ordering Guide .......................................................................... 27
General Description......................................................................... 1
Functional Block Diagram .............................................................. 1
Product Highlights ........................................................................... 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
Timing Specifications .................................................................. 5
Absolute Maximum Ratings............................................................ 6
ESD Caution.................................................................................. 6
Pin Configuration and Function Descriptions............................. 7
Terminology ...................................................................................... 9
Control Register.............................................................................. 10
Theory of Operation ...................................................................... 11
Converter Details........................................................................ 11
Circuit Description..................................................................... 11
Track/Hold Amplifier ................................................................ 12
Reference ..................................................................................... 13
Timing and Control ................................................................... 13
CEXT Functioning......................................................................... 16
REVISION HISTORY
9/06—Rev. B to Rev. C
Updated Format..................................................................Universal
Changes to Table 1............................................................................ 3
Updated Outline Dimensions....................................................... 25
Changes to Ordering Guide .......................................................... 27
2/01—Rev. A to Rev. B
Rev. C | Page 2 of 28
AD7890
SPECIFICATIONS
VDD = 5 V, AGND = DGND = 0 V, REF IN = 2.5 V, fCLK IN = 2.5 MHz external, MUX OUT connect to SHA IN. All specifications TMIN to
MAX, unless otherwise noted.
T
Table 1.
Parameter
A Versions1 B Versions S Version
Unit
Test Conditions/Comments
CONVST
DYNAMIC PERFORMANCE
Signal to (Noise + Distortion) Ratio2
Total Harmonic Distortion (THD)2
Peak Harmonic or Spurious Noise2
Intermodulation Distortion
2nd Order Terms
Using external
, any channel
70
−77
−78
70
−77
−78
70
−77
−78
dB min
dB max
dB max
fIN = 10 kHz sine wave, fSAMPLE = 100 kHz3
fIN = 10 kHz sine wave, fSAMPLE = 100 kHz3
fIN = 10 kHz sine wave, fSAMPLE = 100 kHz3
fa = 9 kHz, fb = 9.5 kHz, fSAMPLE = 100 kHz3
−80
−80
−80
−80
−80
−80
−80
−80
−80
dB typ
dB typ
dB max
3rd Order Terms
Channel-to-Channel Isolation2
fIN = 1 kHz sine wave
DC ACCURACY
Resolution
12
12
12
12
12
12
Bits
Bits
Min. Resolution for Which No
Missing Codes Are Guaranteed
Relative Accuracy2
Differential Nonlinearity2
Positive Full-Scale Error2
Full-Scale Error Match4
AD7890-2, AD7890-4
Unipolar Offset Error2
Unipolar Offset Error Match
AD7890-10 Only
1
1
0.5
1
1
1
LSB max
LSB max
LSB max
LSB max
2.5
2
2.5
2
2.5
2
2
2
2
2
2
2
LSB max
LSB max
Negative Full-Scale Error2
Bipolar Zero Error2
Bipolar Zero Error Match
ANALOG INPUTS
2
5
2
5
2
5
LSB max
LSB max
LSB max
2
2
2
AD7890-10
Input Voltage Range
Input Resistance
10
20
10
20
10
20
Volts
kΩ min
AD7890-4
Input Voltage Range
Input Resistance
0 to 4.096
11
0 to 4.096
11
0 to 4.096
11
Volts
kΩ min
AD7890-2
Input Voltage Range
Input Current
0 to 2.5
50
0 to 2.5
50
0 to 2.5
200
Volts
nA max
MUX OUT OUTPUT
Output Voltage Range
Output Resistance
AD7890-10, AD7890-4
AD7890-2
0 to 2.5
0 to 2.5
0 to 2.5
Volts
3/5
2
3/5
2
3/5
2
kΩ min/kΩ max
kΩ max
Assuming VIN is driven from low impedance
SHA IN INPUT
Input Voltage Range
Input Current
0 to 2.5
50
0 to 2.5
50
0 to 2.5
50
Volts
nA max
REFERENCE OUTPUT/INPUT
REF IN Input Voltage Range
Input Impedance
Input Capacitance5
REF OUT Output Voltage
REF OUT Error @ 25°C
TMIN to TMAX
2.375/2.625
2.375/2.625 2.375/2.625 V min/V max
2.5 V 5ꢀ
1.6
10
2.5
10
20
25
2
1.6
10
1.6
10
kΩ min
pF max
Resistor connected to internal reference node
2.5
2.5
V nom
10
20
25
10
25
25
mV max
mV max
ppm/°C typ
kΩ nom
REF OUT Temperature Coefficient
REF OUT Output Impedance
2
2
Rev. C | Page 3 of 28
AD7890
Parameter
A Versions1 B Versions S Version
Unit
Test Conditions/Comments
LOGIC INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current, IIN
2.4
0.8
10
2.4
0.8
10
2.4
0.8
10
V min
VDD = 5 V 5ꢀ
VDD = 5 V 5ꢀ
VIN = 0 V to VDD
V max
μA max
pF max
5
10
10
10
Input Capacitance, CIN
LOGIC OUTPUTS
Output High Voltage, VOH
Output Low Voltage, VOL
Serial Data Output Coding
AD7890-10
4.0
0.4
4.0
0.4
4.0
0.4
V min
V max
ISOURCE = 200 μA
ISINK = 1.6 mA
Twos Complement
Straight (Natural) Binary
Straight (Natural) Binary
AD7890-4
AD7890-2
CONVERSION RATE
Conversion Time
5.9
2
5.9
2
5.9
2
μs max
μs max
fCLK IN = 2.5 MHz, MUX OUT, connected to
SHA IN
Track/Hold Acquisition Time2, 5
POWER REQUIREMENTS
VDD
5
10
15
5
10
15
5
10
15
V nom
mA max
μA typ
5ꢀ for specified performance
Logic inputs = 0 V or VDD
Logic inputs = 0 V or VDD
IDD (Normal Mode)
IDD (Standby Mode)6 @ 25°C
Power Dissipation
Normal Mode
Standby Mode @ 25°C
50
75
50
75
50
75
mW max
μW typ
Typically 30 mW
1 Temperature ranges are as follows: A, B Versions: −40°C to +85°C; S Version: −55°C to +125°C.
2 See the Terminology section.
3 This sample rate is only achievable when using the part in external clocking mode.
4 Full-scale error match applies to positive full scale for the AD7890-2 and AD7890-4. It applies to both positive and negative full scale for the AD7890-10.
5 Sample tested @ 25°C to ensure compliance.
6 Analog inputs on AD7890-10 must be at 0 V to achieve correct power-down current.
Rev. C | Page 4 of 28
AD7890
TIMING SPECIFICATIONS
VDD = 5 V 5ꢀ, AGND = DGND = 0 V, REF IN = 2.5 V, fCLK IN = 2.5 MHz external, MUX OUT connected to SHA IN.
Parameter1, 2
Limit at TMIN, TMAX (A, B, S Versions)
Unit
Conditions/Comments
3
fCLKIN
100
2.5
0.3 × tCLK IN
0 3 × tCLK IN
25
kHz min
MHz max
ns min
ns min
ns max
ns max
μs max
ns min
Master Clock Frequency. For specified performance.
tCLKIN IN LO
tCLK IN HI
tr4
tf4
Master Clock Input Low Time.
Master Clock Input High Time.
Digital Output Rise Time. Typically 10 ns.
Digital Output Fall Time. Typically 10 ns.
Conversion Time.
25
tCONVERT
tCST
5.9
100
CONVST
Pulse Width.
Self-Clocking Mode
t1
tCLK IN HI + 50
ns max
ns max
ns nom
ns nom
ns max
ns max
ns max
ns min
ns max
ns min
ns min
ns min
ns min
RFS
RFS
Low to SCLK Falling Edge.
Low to Data Valid Delay.
5
t2
25
t3
t4
tCLK IN HI
tCLK IN LO
20
SCLK High Pulse Width.
SCLK Low Pulse Width.
SCLK Rising Edge to Data Valid Delay.
5
t5
t6
40
RFS
Delay.
SCLK Rising Edge to
6
t7
50
0
Bus Relinquish Time after Rising Edge of SCLK.
TFS
t8
Low to SCLK Falling Edge.
tCLK IN + 50
0
t9
TFS
Data Valid to Falling Edge Setup Time (A2 Address Bit).
t10
t11
t12
20
10
20
Data Valid to SCLK Falling Edge Setup Time.
Data Valid to SCLK Falling Edge Hold Time.
TFS
to SCLK Falling Edge Hold Time.
External Clocking Mode
t13
20
40
50
50
35
20
50
90
20
10
15
40
ns min
ns max
ns min
ns min
ns max
ns min
ns max
ns max
ns min
ns min
ns min
ns min
RFS
RFS
Low to SCLK Falling Edge Setup Time.
Low to Data Valid Delay.
5
t14
t15
t16
SCLK High Pulse Width.
SCLK Low Pulse Width.
SCLK Rising Edge to Data Valid Delay.
5
t17
t18
RFS
to SCLK Falling Edge Hold Time.
Bus Relinquish Time after Rising Edge of
Bus Relinquish Time after Rising Edge of SCLK.
TFS
6
RFS
t19
.
6
t19A
t20
t21
t22
t23
Low to SCLK Falling Edge Setup Time.
Data Valid to SCLK Falling Edge Setup Time.
Data Valid to SCLK Falling Edge Hold Time.
TFS
to SCLK Falling Edge Hold Time.
1 Sample tested at −25°C to ensure compliance. All input signals are specified with tr = tf = 5 ns (10ꢀ to 90ꢀ of 5 V) and timed from a voltage level of 1.6 V.
2 See Figure 10 to Figure 13.
3 The AD7890 is production tested with fCLK IN at 2.5 MHz. It is guaranteed by characterization to operate at 100 kHz.
4 Specified using 10ꢀ and 90ꢀ points on waveform of interest.
5 These numbers are measured with the load circuit of Figure 2 and defined as the time required for the output to cross 0.8 V or 2.4 V.
6 These numbers are derived from the measured time taken by the data output to change 0.5 V when loaded with the circuit of Figure 2. The measured number is then
extrapolated back to remove effects of charging or discharging the 50 pF capacitor. This means that the times quoted in the timing characteristics are the true bus
relinquish times of the part and as such are independent of external bus loading capacitances.
1.6mA
TO OUTPUT
PIN
2.1V
50pF
200µA
Figure 2. Load Circuit for Access Time and Bus Relinquish Time
Rev. C | Page 5 of 28
AD7890
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
Parameter
Rating
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
VDD to AGND
VDD to DGND
Analog Input Voltage to AGND
AD7890-10, AD7890-4
AD7890-2
Reference Input Voltage to AGND
Digital Input Voltage to DGND
Digital Output Voltage to DGND
Operating Temperature Range
Commercial (A, B Versions)
Extended (S Version)
−0.3 V to +7 V
−0.3 V to +7 V
17 V
−5 V, +10 V
−0.3 V to VDD + 0.3 V
−0.3 V to VDD + 0.3 V
−0.3 V to VDD + 0.3 V
ESD CAUTION
−40°C to +85°C
−55°C to +125°C
−65°C to +150°C
150°C
Storage Temperature Range
Junction Temperature
PDIP Package, Power Dissipation
θJA Thermal Impedance
Lead Temperature (Soldering, 10 sec)
CERDIP Package, Power Dissipation
450 mW
105°C/W
260°C
450 mW
θJA Thermal Impedance
70°C/W
Lead Temperature (Soldering, 10 sec)
SOIC_W Package, Power Dissipation
300°C
450 mW
θJA Thermal Impedance
75°C/W
Lead Temperature, Soldering
Vapor Phase (60 sec)
Infrared (15 sec)
215°C
220°C
Rev. C | Page 6 of 28
AD7890
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
AGND
SMODE
DGND
1
24
23
22
21
20
19
18
17
16
REF OUT/REF IN
V
2
IN8
V
3
IN7
C
V
4
EXT
IN6
AD7890
TOP VIEW
(Not to Scale)
V
CONVST
CLK IN
SCLK
5
IN5
V
6
IN4
V
7
IN3
V
8
TFS
IN2
V
9
RFS
IN1
10
11
12
15 AGND
DATA OUT
DATA IN
14 SHA IN
13 MUX OUT
V
DD
Figure 3. Pin Configuration
Table 2. Pin Function Descriptions
Pin No. Mnemonic Description
1
2
AGND
SMODE
Analog Ground. Ground reference for track/hold, comparator, and DAC.
Control Input. Determines whether the part operates in its external clocking (slave) or self-clocking (master)
serial mode. With SMODE at a logic low, the part is in its self-clocking serial mode with RFS and SCLK as
outputs. This self-clocking mode is useful for connection to shift registers or to serial ports of DSP processors.
With SMODE at a logic high, the part is in its external clocking serial mode with SCLK and RFS as inputs. This
external clocking mode is useful for connection to the serial port of microcontrollers, such as the 8xC51 and
the 68HCxx, and for connection to the serial ports of DSP processors.
3
4
DGND
CEXT
Digital Ground. Ground reference for digital circuitry.
External Capacitor. An external capacitor is connected to this pin to determine the length of the internal pulse
(see the Control Register section). Larger capacitances on this pin extend the pulse to allow for settling time
delays through an external antialiasing filter or signal conditioning circuitry.
5
CONVST
Convert Start. Edge-triggered logic input. A low-to-high transition on this input puts the track/hold into hold
and initiates conversion if the internal pulse has timed out (see the Control Register section). If the internal
pulse is active when the CONVST goes high, the track/hold does not proceed to hold until the pulse times out.
If the internal pulse times out when CONVST goes high, the rising edge of CONVST drives the track/hold into
hold and initiates conversion.
6
7
CLK IN
SCLK
Clock Input. An external TTL-compatible clock is applied to this input pin to provide the clock source for the
conversion sequence. In the self-clocking serial mode, the SCLK output is derived from this CLK IN pin.
Serial Clock Input. In the external clocking (slave) mode (see the Serial Interface section), this is an externally
applied serial clock used to load serial data to the control register and to access data from the output register.
In the self-clocking (master) mode, the internal serial clock, which is derived from the clock input (CLK IN),
appears on this pin. Once again, it is used to load serial data to the control register and to access data from the
output register.
8
9
TFS
RFS
Transmit Frame Synchronization Pulse. Active low logic input with serial data expected after the falling edge of
this signal.
Receive Frame Synchronization Pulse. In the external clocking mode, this pin is an active low logic input with
RFS provided externally as a strobe or framing pulse to access serial data from the output register. In the self-
clocking mode, it is an active low output, which is internally generated and provides a strobe or framing pulse
for serial data from the output register. For applications which require that data be transmitted and received at
the same time, RFS and TFS should be connected together.
10
11
DATA OUT
DATA IN
Serial Data Output. Sixteen bits of serial data are provided with one leading zero, preceding the three address
bits of the control register and the 12 bits of conversion data. Serial data is valid on the falling edge of SCLK for
sixteen edges after RFS goes low. Output coding from the ADC is twos complement for the AD7890-10 and
straight binary for the AD7890-4 and AD7890-2.
Serial Data Input. Serial data to be loaded to the control register is provided at this input. The first five bits of
serial data are loaded to the control register on the first five falling edges of SCLK after TFS goes low. Serial data
on subsequent SCLK edges is ignored while TFS remains low.
12
13
VDD
MUX OUT
Positive Supply Voltage, 5 V 5ꢀ.
Multiplexer Output. The output of the multiplexer appears at this pin. The output voltage range from this
output is 0 V to 2.5 V for the nominal analog input range to the selected channel. The output impedance of this
output is nominally 3.5 kΩ. If no external antialiasing filter is required, MUX OUT should be connected to SHA IN.
Rev. C | Page 7 of 28
AD7890
Pin No. Mnemonic
Description
14
SHA IN
Track/Hold Input. The input to the on-chip track/hold is applied to this pin. It is a high impedance input and the
input voltage range is 0 V to 2.5 V.
15
16
AGND
VIN1
Analog Ground. Ground reference for track/hold, comparator, and DAC.
Analog Input Channel 1. Single-ended analog input. The analog input range on is 10 V (AD7890-10), 0 V to
4.096 V (AD7890-4), and 0 V to 2.5 V (AD7890-2). The channel to be converted is selected using the A0, A1, and
A2 bits in the control register. The multiplexer has guaranteed break-before-make operation.
17
18
19
20
21
22
23
24
VIN2
VIN3
VIN4
VIN5
VIN6
VIN7
VIN8
Analog Input Channel 2. Single-ended analog input. The analog input range on is 10 V (AD7890-10), 0 V to
4.096 V (AD7890-4), and 0 V to 2.5 V (AD7890-2). The channel to be converted is selected using the A0, A1, and
A2 bits in the control register. The multiplexer has guaranteed break-before-make operation.
Analog Input Channel 3. Single-ended analog input. The analog input range on is 10 V (AD7890-10), 0 V to
4.096 V (AD7890-4), and 0 V to 2.5 V (AD7890-2). The channel to be converted is selected using the A0, A1, and
A2 bits in the control register. The multiplexer has guaranteed break-before-make operation.
Analog Input Channel 4. Single-ended analog input. The analog input range on is 10 V (AD7890-10), 0 V to
4.096 V (AD7890-4), and 0 V to 2.5 V (AD7890-2). The channel to be converted is selected using the A0, A1, and
A2 bits in the control register. The multiplexer has guaranteed break-before-make operation.
Analog Input Channel 5. Single-ended analog input. The analog input range on is 10 V (AD7890-10), 0 V to
4.096 V (AD7890-4), and 0 V to 2.5 V (AD7890-2). The channel to be converted is selected using the A0, A1, and
A2 bits in the control register. The multiplexer has guaranteed break-before-make operation.
Analog Input Channel 6. Single-ended analog input. The analog input range on is 10 V (AD7890-10), 0 V to
4.096 V (AD7890-4), and 0 V to 2.5 V (AD7890-2). The channel to be converted is selected using the A0, A1, and
A2 bits in the control register. The multiplexer has guaranteed break-before-make operation.
Analog Input Channel 7. Single-ended analog input. The analog input range on is 10 V (AD7890-10), 0 V to
4.096 V (AD7890-4), and 0 V to 2.5 V (AD7890-2). The channel to be converted is selected using the A0, A1, and
A2 bits in the control register. The multiplexer has guaranteed break-before-make operation.
Analog Input Channel 8. Single-ended analog input. The analog input range on is 10 V (AD7890-10), 0 V to
4.096 V (AD7890-4) and 0 V to 2.5 V (AD7890-2). The channel to be converted is selected using the A0, A1, and
A2 bits in the control register. The multiplexer has guaranteed break-before-make operation.
REF OUT/REF IN Voltage Reference Output/Input. The part can be used with either its own internal reference or with an external
reference source. The on-chip 2.5 V reference voltage is provided at this pin. When using this internal reference
as the reference source for the part, REF OUT should decoupled to AGND with a 0.1 μF disc ceramic capacitor.
The output impedance of this reference source is typically 2 kΩ. When using an external reference source as
the reference voltage for the part, the reference source should be connected to this pin. This overdrives the
internal reference and provides the reference source for the part. The REF IN input is buffered on-chip. The
nominal reference voltage for correct operation of the AD7890 is 2.5 V.
Rev. C | Page 8 of 28
AD7890
TERMINOLOGY
Signal to (Noise + Distortion) Ratio
Channel-to-Channel Isolation
This is the measured ratio of signal to (noise + distortion) at the
output of the A/D converter. The signal is the rms amplitude of
the fundamental. Noise is the rms sum of all nonfundamental
signals up to half the sampling frequency (fS/2), excluding dc.
The ratio is dependent upon the number of quantization levels
in the digitization process; the more levels, the smaller the
quantization noise. The theoretical signal to (noise + distortion)
ratio for an ideal N-bit converter with a sine wave input is given by:
Channel-to-channel isolation is a measure of the level of crosstalk
between channels. It is measured by applying a full-scale 1 kHz
signal to any one of the other seven inputs and determining how
much that signal is attenuated in the channel of interest. The figure
given is the worst case across all eight channels.
Relative Accuracy
Relative accuracy or endpoint nonlinearity is the maximum
deviation from a straight line passing through the endpoints of
the ADC transfer function.
Signal to (Noise + Distortion) = (6.02N + 1.76) dB
Thus, for a 12-bit converter, this is 74 dB.
Differential Nonlinearity
Total Harmonic Distortion
Total harmonic distortion (THD) is the ratio of the rms sum of
harmonics to the fundamental. For the AD7890, it is defined as
This is the difference between the measured and the ideal 1 LSB
change between any two adjacent codes in the ADC.
Positive Full-Scale Error (AD7890-10)
2
2
2
2
2
V2 + V3 +V4 + V5 +V6
This is the deviation of the last code transition (01 . . . 110 to
01 . . . 111) from the ideal (4 × REF IN − 1 LSB) after the
bipolar zero error has been adjusted out.
THD(dB) = 20log
V1
where:
V1 is the rms amplitude of the fundamental and
V2, V3, V4, V5, and V6 are the rms amplitudes of the second
Positive Full-Scale Error (AD7890-4)
This is the deviation of the last code transition (11 . . . 110 to
11 . . . 111) from the ideal (1.638 × REF IN − 1 LSB) after the
unipolar offset error has been adjusted out.
through the sixth harmonics.
Peak Harmonic or Spurious Noise
Positive Full-Scale Error (AD7890-2)
Peak harmonic or spurious noise is defined as the ratio of the
rms value of the next largest component in the ADC output
spectrum (up to fS/2 and excluding dc) to the rms value of the
fundamental. Normally, the value of this specification is
determined by the largest harmonic in the spectrum, but for
parts where the harmonics are buried in the noise floor, it is
determined by a noise peak.
This is the deviation of the last code transition (11 . . . 110 to
11 . . . 111) from the ideal (REF IN − 1 LSB) after the unipolar
offset error has been adjusted out.
Bipolar Zero Error (AD7890-10)
This is the deviation of the midscale transition (all 0s to all 1s)
from the ideal 0 V (AGND).
Intermodulation Distortion
Unipolar Offset Error (AD7890-2, AD7890-4)
This is the deviation of the first code transition (00 . . . 000 to
00 . . . 001) from the ideal 0 V (AGND).
With inputs consisting of sine waves at two frequencies, fa and
fb, any active device with nonlinearities creates distortion
products at sum and difference frequencies of mfa nfb where
m, n = 0, 1, 2, 3, and so on. Intermodulation terms are those for
which neither m nor n are equal to zero. For example, the
second-order terms include (fa + fb) and (fa − fb), while the
third-order terms include (2fa + fb), (2fa − fb), (fa + 2fb), and
(fa − 2fb).
Negative Full-Scale Error (AD7890-10)
This is the deviation of the first code transition (10 . . . 000 to
10 . . . 001) from the ideal (−4 × REF IN + 1 LSB) after bipolar
zero error has been adjusted out.
Track/Hold Acquisition Time
The AD7890 is tested using the CCIF standard where two input
frequencies near the top end of the input bandwidth are used.
In this case, the second and third order terms are of different
significance. The second-order terms are usually distanced in
frequency from the original sine waves while the third-order
terms are usually at a frequency close to the input frequencies.
As a result, the second- and third-order terms are specified
separately. The calculation of the intermodulation distortion is
as per the THD specification where it is the ratio of the rms
sum of the individual distortion products to the rms amplitude
of the fundamental expressed in dBs.
Track/hold acquisition time is the time required for the output
of the track/hold amplifier to reach its final value, within
1/2 LSB, after the end of conversion (the point at which the
track/hold returns to track mode). It also applies to situations
where a change in the selected input channel takes place or
where there is a step input change on the input voltage applied
to the selected VIN input of the AD7890. It means that the user
must wait for the duration of the track/hold acquisition time
after the end of conversion or after a channel change/step input
change to VIN before starting another conversion, to ensure that
the part operates to specification.
Rev. C | Page 9 of 28
AD7890
CONTROL REGISTER
The control register for the AD7890 contains 5 bits of information.
Six serial clock pulses must be provided to the part in order to
write data to the control register (seven if the write is required
If, however, the CONV bit of the register is set to a Logic 1, then
a conversion is initiated whenever a control register write takes
TFS
place regardless of how many serial clock cycles the
TFS
to put the part in standby mode). If
returns high before six
remains low for. The default (power-on) condition of all bits in
the control register is 0.
serial clock cycles, then no data transfer takes place to the
control register and the write cycle has to be restarted to write
the data to the control register.
MSB
LSB
A2
A1
A0
CONV
STBY
Table 3.
Bit Name Description
A2
A1
A0
Address Input. This input is the most significant address input for multiplexer channel selection.
Address Input. This is the 2nd most significant address input for multiplexer channel selection.
Address Input. Least significant address input for multiplexer channel selection. When the address is written to the control
register, an internal pulse is initiated, the pulse width of which is determined by the value of capacitance on the CEXT pin. When
this pulse is active, it ensures the conversion process cannot be activated. This allows for the multiplexer settling time,
track/hold acquisition time before the track/hold goes into hold, and the conversion is initiated. In applications where there is
an antialiasing filter between the MUX OUT pin and the SHA IN pin , the filter settling time can be taken into account before the
input on the SHA IN pin is sampled. When the internal pulse times out, the track/hold goes into hold and conversion is initiated.
CONV
STBY
Conversion Start. Writing a 1 to this bit initiates a conversion in a similar manner to the CONVST input. Continuous conversion
starts do not take place when there is a 1 in this location. The internal pulse and the conversion process are initiated after the
sixth serial clock cycle of the write operation if a 1 is written to this bit. With a 1 in this bit, the hardware conversion start (the
CONVST input) is disabled. Writing a 0 to this bit enables the hardware CONVST input.
Standby Mode Input. Writing a 1 to this bit places the device in its standby, or power-down, mode. Writing a 0 to this bit places
the device in its normal operating mode. The part does not enter its standby mode until the seventh falling edge of SCLK in a
write operation. Therefore, the part requires seven serial clock pulses in its serial write operation if it is required to put the part
into standby.
Rev. C | Page 10 of 28
AD7890
THEORY OF OPERATION
CONVERTER DETAILS
This allows the part to operate at throughput rates up to
117 kHz in the external clocking mode and achieve data sheet
specifications. The part can operate at slightly higher
throughput rates (up to 127 kHz), again in external clocking
mode with degraded performance (see the Timing and Control
section). The throughput rate for self-clocking mode is limited
by the serial clock rate to 78 kHz.
The AD7890 is an 8-channel, 12-bit, single supply, serial data
acquisition system. It provides the user with signal scaling,
multiplexer, track/hold, reference, ADC, and versatile serial
logic functions on a single chip. The signal scaling allows the
part to handle 10 V input signals (AD7890-10) and 0 V to
4.096 V input signals (AD7890-4) while operating from a single
5 V supply. The AD7890-2 contains no signal scaling and
accepts an analog input range of 0 V to 2.5 V. The part operates
from a 2.5 V reference, which can be provided from the part’s
own internal reference or from an external reference source.
All unused inputs should be connected to a voltage within the
nominal analog input range to avoid noise pickup. On the
AD7890-10, if any one of the input channels which are not
being converted goes more negative than −12 V, it can interfere
with the conversion on the selected channel.
Unlike other single chip data acquisition solutions, the AD7890
provides the user with separate access to the multiplexer and
the ADC. This means that the flexibility of separate multiplexer
and ADC solutions is not sacrificed with the one-chip solution.
With access to the multiplexer output, the user can implement
external signal conditioning between the multiplexer and the
track/hold. It means that one antialiasing filter can be used on
the output of the multiplexer to provide the antialiasing
function for all eight channels.
CIRCUIT DESCRIPTION
The AD7890 is offered as three part types: the AD7890-10
handles a 10 V input voltage range, the AD7890-4 handles a
0 V to 4.096 V input range, while the AD7890-2 handles a 0 V
to 2.5 V input voltage range.
AD7890-10 Analog Input
Figure 4 shows the analog input section for the AD7890-10. The
analog input range for each of the analog inputs is 10 V into
an input resistance of typically 33 kΩ. This input is benign with
no dynamic charging currents with the resistor attenuator stage
followed by the multiplexer and, in cases where MUX OUT is
connected to SHA IN, this is followed by the high input
impedance stage of the track/hold amplifier. The designed code
transitions occur on successive integer LSB values (such as:
1 LSB, 2 LSBs, 3 LSBs...). Output coding is twos complement
binary with 1 LSB − FSR/4096 = 20 V/4096 = 4.88 mV. The
ideal input/output transfer function is shown in Table 4.
Conversion is initiated on the AD7890 either by pulsing the
CONVST
input or by writing a Logic 1 to the CONV bit of the
CONVST
control register. When using the hardware
input, on
CONVST
the rising edge of the
signal, the on-chip track/hold
goes from track to hold mode and the conversion sequence is
started, provided the internal pulse has timed out. This internal
pulse (which appears at the CEXT pin) is initiated whenever the
multiplexer address is loaded to the AD7890 control register.
This pulse goes from high to low when a serial write to the part
is initiated. It starts to discharge on the sixth falling clock edge
of SCLK in a serial write operation to the part. The track/hold
cannot go into hold and conversion cannot be initiated until the
MUX OUT
2.5V
REFERENCE
CEXT pin has crossed its trigger point of 2.5 V. The discharge
2kΩ
time of the voltage on CEXT depends upon the value of capacitor
connected to the CEXT pin (see the CEXT Functioning section).
The fact that the pulse is initiated every time a write to the
control register takes place means that the software conversion
start and track/hold signal is always delayed by the internal pulse.
REF OUT/
REF IN
TO ADC
REFERENCE
CIRCUITRY
7.5kΩ
1
200Ω
30kΩ
V
INX
10kΩ
The conversion clock for the part is generated from the clock
signal applied to the CLK IN pin of the part. Conversion time
for the AD7890 is 5.9 μs from the rising edge of the hardware
AGND
AD7890-10
1
EQUIVALENT ON-RESISTANCE OF MULTIPLEXER
CONVST
signal and the track/hold acquisition time is 2 μs. To
Figure 4. AD7890-10 Analog Input Structure
obtain optimum performance from the part, the data read
operation or control register write operation should not occur
during the conversion or during 500 ns prior to the next
conversion.
Rev. C | Page 11 of 28
AD7890
Table 4. Ideal Input/Output Code Table for the AD7890-10
this is followed by the high input impedance stage of the track/
hold amplifier. The analog input range is, therefore, 0 V to 2.5 V
into a high impedance stage with an input current of less than
50 nA. The designed code transitions occur on successive
integer LSB values (such as: l LSB, 2 LSBs, 3 LSBs . . . FS-1
LSBs). Output coding is straight (natural) binary with 1 LSB =
FSR/4096 = 2.5 V/4096 = 0.61 mV. The ideal input/output
transfer function is shown in Table 6.
Analog Input1
Digital Output Code Transition
011 . . . 110 to 011 . . . 111
011 . . . 101 to 011 . . . 110
011 . . . 100 to 011 . . . 101
000 . . . 000 to 000 . . . 001
111 . . . 111 to 000 . . . 000
111 . . . 110 to 111 . . . 111
+FSR/2 − 1 LSB2 (9.995117 V)
+FSR/2 − 2 LSBs (9.990234 V)
+FSR/2 − 3 LSBs (9.985352 V)
AGND + 1 LSB (0.004883 V)
AGND (0.000000 V)
AGND − 1 LSB (−0.004883 V)
−FSR/2 + 3 LSBs (−9.985352 V) 100 . . . 010 to 100 . . . 011
−FSR/2 + 2 LSBs (−9.990234 V) 100 . . . 001 to 100 . . . 010
Table 6. Ideal Input/Output Code Table for the AD7890-2
Analog Input1
Digital Output Code Transition
111 . . . 110 to 111 . . . 111
111 . . . 101 to 111 . . . 110
111 . . . 100 to 111 . . . 101
−FSR/2 + 1 LSB (−9.995117 V)
100 . . . 000 to 100 . . . 001
+FSR − 1 LSB2 (2.499390 V)
+FSR − 2 LSBs (2.498779 V)
+FSR − 3 LSBs (2.498169 V)
1FSR is full-scale range and is 20 V with REF IN = 2.5 V.
21 LSB = FSR/4096 = 4.883 mV with REF IN = 2.5 V.
AGND + 3 LSBs (0.001831 V) 000 . . . 010 to 010 . . . 011
AGND + 2 LSBs (0.001221 V) 000 . . . 001 to 001 . . . 010
AD7890-4 Analog Input
Figure 5 shows the analog input section for the AD7890-4. The
analog input range for each of the analog inputs is 0 to 4.096 V
into an input resistance of typically 15 kΩ. This input is benign
with no dynamic charging currents with the resistor attenuator
stage followed by the multiplexer and in cases where MUX OUT is
connected to SHA IN this is followed by the high input
impedance stage of the track/hold amplifier. The designed code
transitions occur on successive integer LSB values (such as:
1 LSB, 2 LSBs, 3 LSBs . . . ). Output coding is straight (natural)
binary with 1 LSB = FSR/4096 = 4.096 V/4096 = 1 mV. The
ideal input/output transfer function is shown in Table 5.
MUX OUT
AGND + 1 LSB (0.000610 V)
000 . . . 000 to 000 . . . 001
1FSR is full-scale range and is 2.5 V with REF IN = 2.5 V.
21 LSB = FSR/4096 = 0.61 mV with REF IN = 2.5 V.
TRACK/HOLD AMPLIFIER
The SHA IN input on the AD7890 connects directly to the input
stage of the track/hold amplifier. This is a high impedance input
with input leakage currents of less than 50 nA. Connecting the
MUX OUT pin directly to the SHA IN pin connects the
multiplexer output directly to the track/hold amplifier. The input
voltage range for this input is 0 V to 2.5 V. If external circuitry is
connected between MUX OUT and SHA IN, then the user must
ensure that the input voltage range to the SHA IN input is 0 V to
2.5 V to ensure that the full dynamic range of the converter is
utilized.
2.5V
REFERENCE
2kΩ
REF OUT/
REF IN
TO ADC
REFERENCE
CIRCUITRY
The track/hold amplifier on the AD7890 allows the ADC to
accurately convert an input sine wave of full-scale amplitude to
12-bit accuracy. The input bandwidth of the track/hold is
greater than the Nyquist rate of the ADC even when the ADC is
operated at its maximum throughput rate of 117 kHz (for example,
the track/hold can handle input frequencies in excess of 58 kHz).
1
200Ω
6kΩ
V
INX
9.38kΩ
AGND
AD7890-4
1
EQUIVALENT ON-RESISTANCE OF MULTIPLEXER
The track/hold amplifier acquires an input signal to 12-bit
accuracy in less than 2 μs. The operation of the track/hold is
essentially transparent to the user. The track/hold amplifier
goes from its tracking mode to its hold mode at the start of
conversion. The start of conversion is the rising edge of
Figure 5. AD7890-4 Analog Input Structure
Table 5. Ideal Input/Output Code Table for the AD7890-4
Analog Input1
Digital Output Code Transition
111 . . . 110 to 111 . . . 111
111 . . . 101 to 111 . . . 110
111 . . . 100 to 111 . . . 101
000 . . . 010 to 000 . . . 011
000 . . . 001 to 000 . . . 010
000 . . . 000 to 000 . . . 001
+FSR − 1 LSB2 (4.095 V)
+FSR − 2 LSBs (4.094 V)
+FSR − 3 LSBs (4.093 V)
AGND + 3 LSBs (0.003 V)
AGND + 2 LSBs (0.002 V)
AGND + 1 LSB (0.001 V)
CONVST
(assuming the internal pulse has timed out) for
hardware conversion starts and for software conversion starts is
the point where the internal pulse is timed out. The aperture
time for the track/hold (for example, the delay time between the
CONVST
external
signal and the track/hold actually going into
1FSR is full-scale range and is 4.096 V with REF IN = 2.5 V.
21 LSB = FSR/4096 = 1 mV with REF IN = 2.5 V.
hold) is typically 15 ns. For software conversion starts, the time
depends on the internal pulse widths. Therefore, for software
conversion starts, the sampling instant is not very well defined.
For sampling systems which require well defined, equidistant
sampling, it may not be possible to achieve optimum performance
from the part using the software conversion start. At the end of
AD7890-2 Analog Input
The analog input section for the AD7890-2 contains no biasing
resistors and the selected analog input connects to the multi-
plexer and, in cases where MUX OUT is connected to SHA IN,
Rev. C | Page 12 of 28
AD7890
conversion, the part returns to its tracking mode. The acquisition
time of the track/ hold amplifier begins at this point.
the user provides the frame sync and serial clock signals to obtain
the serial data from the part. In this second mode, the user has
control of the serial clock rate up to a maximum of 10 MHz. The
two modes are discussed in the Serial Interface section.
REFERENCE
The AD7890 contains a single reference pin, labeled REF OUT/
REF IN, which either provides access to the part’s own 2.5 V
reference or to which an external 2.5 V reference can be connected
to provide the reference source for the part. The part is specified
with a 2.5 V reference voltage. Errors in the reference source results
in gain errors in the AD7890’s transfer function and adds to the
specified full-scale errors on the part. On the AD7893-10, it also
results in an offset error injected in the attenuator stage.
The part also provides hardware and software conversion start
features. The former provides a well-defined sampling instant
with the track/hold going into hold on the rising edge of the
CONVST
signal. For the software conversion start, a write to
the CONV bit to the control register initiates the conversion
sequence. However, for the software conversion start an internal
pulse has to time out before the input signal is sampled. This
pulse, plus the difficulty in maintaining exactly equal delays
between each software conversion start command, means that
the dynamic performance of the AD7890 may have difficulty
meeting specifications when used in software conversion start
mode. The AD7890 provides separate channel select and
conversion start control. This allows the user to optimize the
throughput rate of the system. Once the track/hold has gone into
hold mode, the input channel can be updated and the input voltage
can settle to the new value while the present conversion is in
progress.
The AD7890 contains an on-chip 2.5 V reference. To use this
reference as the reference source for the AD7890, simply connect a
0.1 μF disc ceramic capacitor from the REF OUT/REF IN pin to
AGND. The voltage which appears at this pin is internally buffered
before being applied to the ADC. If this reference is required for
use external to the AD7890, it should be buffered as the source
impedance of this output is 2 kΩ nominal. The tolerance on the
internal reference is 10 mV at 25°C with a typical temperature
coefficient of 25 ppm/°C and a maximum error over temperature
of 25 mV.
CONVST
Assuming the internal pulse has timed out before the
If the application requires a reference with a tighter tolerance or
the AD7890 needs to be used with a system reference, then the
user has the option of connecting an external reference to this
REF OUT/REF IN pin. The external reference effectively
overdrives the internal reference and thus provides the reference
source for the ADC. The reference input is buffered, but has a
nominal 2 kΩ resistor connected to the AD7890’s internal
reference. Suitable reference sources for the AD7890 include the
AD680, AD780, and REF-43 precision 2.5 V references.
pulse is exercised, the conversion consists of 14.5 master clock
cycles. In the self-clocking mode, the conversion time is defined
CONVST
as the time from the rising edge of
to the falling edge
RFS
of
(for example, when the device starts to transmit its
conversion result). This time includes the 14.5 master clock
cycles plus the updating of the output register and delay time in
RFS
outputting the
signal, resulting in a total conversion time of
5.9 μs maximum. Figure 6 shows the conversion timing for the
AD7890 when used in the self-clocking (master) mode with
CONVST
hardware
internal pulse is not active when the
To ensure this, the channel address to be converted should be
CONVST
. The timing diagram assumes that the
TIMING AND CONTROL
CONVST
signal goes high.
The AD7890 is capable of two interface modes, selected by the
SMODE input. The first of these is a self-clocking mode where
the part provides the frame sync, serial clock, and serial data at
the end of conversion. In this mode the serial clock rate is
determined by the master clock rate of the part (at the CLK IN
input). The second mode is an external clocking mode where
selected by writing to the control register prior to the
pulse. Sufficient setup time should be allowed between the
CONVST
control register write and the
pulse has timed out. The duration of the internal pulse (and hence
the duration of setup time) depends on the value of CEXT
to ensure that the internal
.
CONVST (I)
TRACK/HOLD GOES
INTO THE HOLD
tCONVERT
RFS (O)
SCLK (O)
THREE-STATE
1
DATA OUT (O)
NOTES:
1. (I) SIGNIFIES AN INPUT.
2. (O) SIGNIFIES AN OUTPUT. PULL-UP RESISTOR ON SCLK.
Figure 6. Self-Clocking (Master) Mode Conversion Sequence
Rev. C | Page 13 of 28
AD7890
When using the device in the external-clocking mode, the
output register can be read at any time and the most up-to-date
conversion result is obtained. However, reading data from the
output register or writing data to the control register during
CONVST
to optimize the settling
of the track/hold before the next conversion is initiated.
before the next rising edge of
The diagram shows the read operation and the write operation
taking place in parallel. On the sixth falling edge of SCLK in the
write sequence the internal pulse is initiated. Assuming MUX OUT
is connected to SHA IN, 2 μs are required between this sixth
CONVST
conversion or during the 500 ns prior to the next
results in reduced performance from the part. A read operation
to the output register has the most effect on performance with
the signal-to-noise ratio likely to degrade, especially when
higher serial clock rates are used while the code flicker from the
part also increases (see the Performance section).
CONVST
falling edge of SCLK and the rising edge of
to allow
for the full acquisition time of the track/hold amplifier. With
the serial clock rate at its maximum of 10 MHz, the achievable
throughput rate for the part is 5.9 μs (conversion time) plus 0.6
μs (six serial clock pulses before internal pulse is initiated) plus
2 μs (acquisition time). This results in a minimum throughput
time of 8.5 μs (equivalent to a throughput rate of 117 kHz). If
the part is operated with a slower serial clock, it affects the
achievable throughput rate for optimum performance.
Figure 7 shows the timing and control sequence required to
obtain optimum performance from the part in the external
clocking mode. In the sequence shown, conversion is initiated
CONVST
on the rising edge of
and new data is available in the
output register of the AD7890 5.9 μs later. Once the read
operation has taken place, a further 500 ns should be allowed
CONVST
SCLK
RFS
TFS
tCONVERT
500ns MIN
SERIAL READ
AND WRITE
OPERATIONS
READ AND WRITE
OPERATIONS SHOULD END
500ns PRIOR TO NEXT
NEXT CONVERSION
START COMMAND
CONVERSION IS
INITIATED AND
TRACK/HOLD GOES
INTO HOLD
CONVERSION
ENDS 5.9µs
LATER
RISING EDGE OF CONVST
Figure 7. External Clocking (Slave) Mode Timing Sequence for Optimum Performance
Rev. C | Page 14 of 28
AD7890
CONVST
occurs 5.9 μs later and can be used as either an active
In the self-clocking mode, the AD7890 indicates when
RFS
low or falling edge-triggered interrupt signal to tell the
processor to read the data from the AD7890. Provided the read
operation is completed 500 ns before the rising edge of
conversion is complete by bringing the
line low and
initiating a serial data transfer. In the external clocking mode,
there is no indication of when conversion is complete. In many
applications, this is not a problem as the data can be read from
the part during conversion or after conversion. However,
applications that seek to achieve optimum performance from
the AD7890 has to ensure that the data read does not occur
during conversion or during 500 ns prior to the rising edge
CONVST
, the AD7890 operates to specification.
This scheme limits the throughput rate to 11.8 μs minimum.
However, depending upon the response time of the
microprocessor to the interrupt signal and the time taken by the
processor to read the data, this may be the fastest which the
CONVST
of
.
CONVST
system could have operated. In any case, the
signal
does not have to have a 50:50 duty cycle. This can be tailored to
optimize the throughput rate of the part for a given system.
This can be achieved in either of two ways. The first is to ensure
in software that the read operation is not initiated until 5.9 μs
CONVST
software knows when the
second scheme would be to use the
conversion start signal and an interrupt signal. The simplest
way to do this is to generate a square wave signal for
with high and low times of 5.9 μs (see Figure 8). Conversion is
after the rising edge of
. This is only possible if the
CONVST
CONVST
narrow pulse width. The rising edge of
an active high or rising edge-triggered interrupt. A software
delay of 5.9 μs can then be implemented before data is read
from the part.
Alternatively, the
signal can be used as a normal
CONVST
command is issued. The
CONVST
can be used as
signal as both the
CONVST
CONVST
initiated on the rising edge of
. The falling edge of
CONVST
SCLK
RFS
TFS
500ns MIN
tCONVERT
CONVERSION IS
INITIATED AND
TRACK/HOLD GOES
INTO HOLD
CONVERSION MICROPROCESSOR
SERIAL READ
AND WRITE
OPERATIONS
READ AND WRITE
OPERATIONS SHOULD
END 500ns PRIOR
TO NEXT RISING
NEXT CONVST
RISING EDGE
ENDS 5.9µs
LATER
INT SERVICE
OR POLLING
ROUTINE
EDGE OF CONVST
CONVST
Figure 8.
Used as Status Signal in External Clocking Mode
Rev. C | Page 15 of 28
AD7890
The duration of the internal pulse can be seen on the CEXT pin.
The CEXT pin goes from a low to a high when a serial write to
CEXT FUNCTIONING
The CEXT input on the AD7890 provides a means of determining
how long after a new channel address is written to the part that
a conversion can take place. The reason behind this is two-fold.
First, when the input channel to the AD7890 is changed, the
input voltage on this new channel is likely to be very different
from the previous channel voltage. Therefore, the part’s track/
hold has to acquire the new voltage before an accurate
conversion can take place. An internal pulse delays any
conversion start command (as well as the signal to send the
track/hold into hold) until after this pulse has timed out.
TFS
the part is initiated (on the falling edge of
). It starts to
discharge on the sixth falling edge of SCLK in the serial write
operation. Once the CEXT pin has discharged to crossing its
nominal trigger point of 2.5 V, the internal pulse is timed out.
The internal pulse is initiated each time a write operation to the
control register takes place. As a result, the pulse is initiated and
the conversion process delayed for all software conversion start
commands. For hardware conversion start, it is possible to
separate the conversion start command from the internal pulse.
The second reason is to allow the user to connect external
antialiasing or signal conditioning circuitry between the
MUX OUT pin and the SHA IN pin. This external circuitry
introduces extra settling time into the system. The CEXT pin
provides a means for the user to extend the internal pulse to
take this extra settling time into account. Effectively varying the
value of the capacitor on the CEXT pin varies the duration of the
internal pulse. Figure 9 shows the relationship between the
value of the CEXT capacitor and the internal delay.
If the multiplexer output (MUX OUT) is connected directly to
the track/hold input (SHA IN), then no external settling has to
be taken into account by the internal pulse width. In applications
where the multiplexer is switched and conversion is not
initiated until more than 2 μs after the channel is changed (as is
possible with a hardware conversion start), the user does not
have to worry about connecting any capacitance to the
CEXT pin. The 2 μs equates to the track/hold acquisition time of
the AD7890. In applications where the multiplexer is switched
and conversion is initiated at the same time (such as with a
software conversion start), a 120 pF capacitor should be
connected to CEXT to allow for the acquisition time of the
track/hold before conversion is initiated.
64
56
T
= +25°C
A
48
40
32
24
16
8
T
= +85°C
A
If external circuitry is connected between the MUX OUT pin
and SHA IN pin, then the extra settling time introduced by this
circuitry must be taken into account. In the case where the
multiplexer change command and the conversion start
command are separated, they need to be separated by greater
than the acquisition time of the AD7890 plus the settling time
of the external circuitry if the user does not have to worry about
the CEXT capacitance. In applications where the multiplexer is
switched and conversion is initiated at the same time (such as
with a software conversion start), the capacitor on CEXT needs to
allow for the acquisition time of the track/hold and the settling
time of the external circuitry before conversion is initiated.
T
= –40°C
A
0
0
250
500
750
1000
1250
1500
1750
2000
C
CAPACITANCE (pF)
EXT
Figure 9. Internal Pulse Width vs. CEXT
Rev. C | Page 16 of 28
AD7890
SERIAL INTERFACE
framing signal used for the transfer of data from the AD7890.
This self-clocking mode can be used with processors that allow
an external device to clock their serial port, including most
digital signal processors.
The AD7890’s serial communications port provides a flexible
arrangement to allow easy interfacing to industry-standard
microprocessors, microcontrollers, and digital signal processors.
A serial read to the AD7890 accesses data from the output
register via the DATA OUT line. A serial write to the AD7890
writes data to the control register via the DATA IN line.
Read Operation
Figure 10 shows a timing diagram for reading from the AD7890
Two different modes of operation are available, optimized for
different types of interface where the AD7890 can act either as
master in the system (it provides the serial clock and data
framing signal) or acts as slave (an external serial clock and
framing signal can be provided to the AD7890). The former is
self-clocking mode while the latter is external clocking mode.
RFS
in the self-clocking mode. At the end of conversion,
goes
low and the serial clock (SCLK) and serial data (DATA OUT)
outputs become active. Sixteen bits of data are transmitted with
one leading zero, followed by the three address bits of the
control register, followed by the 12-bit conversion result starting
with the MSB. Serial data is clocked out of the device on the
rising edge of SCLK and is valid on the falling edge of SCLK.
SELF-CLOCKING MODE
RFS
The
output remains low for the duration of the 16 clock
The AD7890 is configured for its self-clocking mode by tying
the SMODE pin of the device to a logic low. In this mode, the
AD7890 provides the serial clock signal and the serial data
th
RFS
cycles. On the 16 rising edge of SCLK, the
high and DATA OUT is disabled.
output is driven
RFS (O)
t6
t1
t3
SCLK (O)
t4
t2
t5
t7
THREE-STATE
THREE-STATE
LEADING
DATA OUT (O)
A2
A1
A0
DB11
DB10
DB0
ZERO
NOTES:
1. (I) SIGNIFIES AN INPUT.
2. (O) SIGNIFIES AN OUTPUT. PULL-UP RESISTOR ON SCLK.
Figure 10. Self-Clocking (Master) Mode Output Register Read
TFS (I)
t12
t8
t3
SCLK (O)
t9
t11
t4
t10
DON’T
CARE
DON’T
CARE
DON’T
CARE
DATA IN (I)
A2
A1
A0
CONV
STBY
NOTES:
1. (I) SIGNIFIES AN INPUT.
2. (O) SIGNIFIES AN OUTPUT. PULL-UP RESISTOR ON SCLK.
Figure 11. Self-Clocking (Master) Mode Control Register Write
Rev. C | Page 17 of 28
AD7890
RFS
However,
must remain low for the duration of the data
Write Operation
transfer operation. Once again, 16th bits of data are transmitted
with one leading zero, followed by the three address bits in the
control register, followed by the 12-bit conversion result starting
Figure 11 shows a write operation to the control register of the
TFS
AD7890. The
input is taken low to indicate to the part that
TFS
a serial write is about to occur.
going low initiates the SCLK
RFS
with the MSB. If
the leading zero is clocked out from the falling edge of
RFS
goes low during the high time of SCLK,
output and this is used to clock data out of the processors serial
port and into the control register of the AD7890. The AD7890
control register requires only five bits of data. These are loaded
on the first five clock cycles of the serial clock with data on all
subsequent clock cycles being ignored. However, the part
requires six serial clock cycles to load data to the control
register. Serial data to be written to the AD7890 must be valid
on the falling edge of SCLK.
RFS
(as
goes low during the low time of SCLK,
the leading zero is clocked out on the next rising edge of SCLK.
RFS
per Figure 12). If
This ensures that, regardless of whether
high time or low time of SCLK, the leading zero is valid on the
RFS
goes low during a
first falling edge of SCLK after
goes low, provided t14 and t17
are adhered to. Serial data is clocked out of the device on the
rising edge of SCLK and is valid on the falling edge of SCLK. At
the end of the read operation, the DATA OUT line is three-stated
EXTERNAL CLOCKING MODE
The AD7890 is configured for its external clocking mode by
tying the SMODE pin of the device to a logic high. In this
RFS
by a rising edge on either the SCLK or
inputs, whichever
occurs first. If a serial read from the output register is in progress
when conversion is complete, the updating of the output register is
RFS
mode, SCLK and
of the AD7890 are configured as inputs.
This external-clocking mode is designed for direct interface to
systems, which provide a serial clock output which is
synchronized to the serial data output including
microcontrollers such as the 80C51, 87C51, 68HC11, and
68HC05, and most digital signal processors.
RFS
deferred until the serial data read is complete and
returns high.
Write Operation
Figure 13 shows a write operation to the control register of the
TFS
AD7890. As with self-clocking mode, the
input goes low to
indicate to the part that a serial write is about to occur. As before,
the AD7890 control register requires only five bits of data. These
are loaded on the first five clock cycles of the serial clock; data on all
subsequent clock cycles are ignored. However, the part requires six
serial clocks to load data to the control register. Serial data to be
written to the AD7890 must be valid on the falling edge of SCLK.
Read Operation
Figure 12 shows the timing diagram for reading from the
RFS
AD7890 in the external clocking mode.
goes low to access
data from the AD7890. The serial clock input does not have to be
continuous. The serial data can be accessed in a number of bytes.
RFS (I)
t18
t13
t15
SCLK (I)
t19
t16
t17
t14
t19A
LEADING
ZERO
THREE-STATE
A2
A1
A0
DB11
DB10
DB0
DATA OUT (O)
NOTES:
1. (I) SIGNIFIES AN INPUT.
2. (O) SIGNIFIES AN OUTPUT.
Figure 12. External Clocking (Slave) Mode Output Register Read
TFS (I)
t20
t23
SCLK (I)
t22
t21
DON’T
CARE
DON’T
CARE
DON’T
CARE
A2
A1
A0
CONV
STBY
DATA IN (I)
NOTES:
1. (I) SIGNIFIES AN INPUT.
2. (O) SIGNIFIES AN OUTPUT. PULL-UP RESISTOR ON SCLK.
Figure 13. External Clocking (Slave) Mode Control Register Write
Rev. C | Page 18 of 28
AD7890
SIMPLIFYING THE INTERFACE
To minimize the number of interconnect lines to the AD7890,
Care must be taken with this scheme that the read operation is
completed before the next conversion starts, if the user wants to
obtain optimum performance from the part. In the case of the
software conversion start, the conversion command is written
to the control register on the sixth serial clock edge. However,
the read operation continues for another 10 serial clock cycles.
To avoid reading during the sampling instant or during
conversion, the user should ensure that the internal pulse width
is sufficiently long (by choosing CEXT) so that the read operation
is completed before the next conversion sequence begins.
Failure to do this results in significantly degraded performance
from the part, both in terms of signal-to-noise ratio and dc
parameters. In the case of a hardware conversion start, the user
should ensure that the delay between the sixth falling edge of
the serial clock in the write operation and the next rising edge
RFS
TFS
the user can connect the
and
lines of the AD7890
together and read and write from the part simultaneously. In
this case, new control register data should be provided on the
DATA IN line selecting the input channel and possibly
providing a conversion start command while the part provides
the result from the conversion just completed on the
DATA OUT line.
In the self-clocking mode, this means that the part provides all
the signals for the serial interface. It does require that the
microprocessor has the data to be written to the control register
TFS
available in its output register when the part brings the
line
low. In the external clocking mode, it means that the user only
has to supply a single frame synchronization signal to control
both the read and write operations.
CONVST
of
is greater than the internal pulse width.
Rev. C | Page 19 of 28
AD7890
MICROPROCESSOR/MICROCONTROLLER INTERFACE
V
DD
The AD7890’s flexible serial interface allows for easy
connection to the serial ports of DSP processors and
microcontrollers. Figure 14 through Figure 17 show the
AD7890 interfaced to a number of different microcontrollers
and DSP processors. In some of the interfaces shown, the
AD7890 is configured as the master in the system, providing
the serial clock and frame sync for the read operation while in
others it acts as a slave with these signals provided by the
microprocessor.
SMODE
P1.0
P1.1
RFS
TFS
8xC51
AD7890
DATA OUT
DATA IN
P3.0
P3.1
SCLK
AD7890 TO 8051 INTERFACE
Figure 14. AD7890 to 8xC51 Interface
Figure 14 shows an interface between the AD7890 and the
AD7890 TO 68HC11 INTERFACE
8xC51 microcontroller. The AD7890 is configured for its
external clocking mode while the 8xC51 is configured for its
Mode 0 serial interface mode. The diagram shown in Figure 14
makes no provisions for monitoring when conversion is
complete on the AD7890 (assuming hardware conversion start
is used). To monitor the conversion time on the AD7890, a
An interface circuit between the AD7890 and the 68HC11
microcontroller is shown in Figure 15. For the interface shown,
the AD7890 is configured for its external clocking mode while
the 68HC11’s SPI port is used and the 68HC11 is configured in
its single-chip mode. The 68HC11 is configured in the master
mode with its CPOL bit set to a Logic 0 and its CPHA bit set to
a Logic 1.
CONVST
scheme, such as the scheme outlined with
Simplifying the Interface section, can be used. This can be
CONVST
in the
implemented in two ways. One is to connect the
line
As with the previous interface, there are no provisions for
monitoring when conversion is complete on the AD7890. To
monitor the conversion time on the AD7890, a scheme, such as
to another parallel port bit, which is configured as an input.
This port bit can then be polled to determine when conversion is
complete. An alternative is to use an interrupt driven system where
CONVST
the scheme outlined with
Interface section, can be used. This can be implemented in two
CONVST
in the Simplifying the
CONVST
INT1
the
line is connected to the
input of the 8xC51.
ways. One is to connect the
line to another parallel
Since the 8xC51 contains only one serial data line, the DATA
OUT and DATA IN lines of the AD7890 must be connected
together. This means that the 8xC51 cannot communicate with
the output register and control register of the AD7890 at the
same time. The 8xC51 outputs the LSB first in a write operation
so care should be taken in arranging the data, which is to be
transmitted to the AD7890. Similarly, the AD7890 outputs the
MSB first during a read operation while the 8xC51 expects the
LSB first. Therefore, the data that is to be read into the serial
port needs to be rearranged before the correct data word from
the AD7890 is available in the microcontroller.
port bit, which is configured as an input. This port bit can then
be polled to determine when conversion is complete. An alternative
CONVST
is to use an interrupt driven system in which case the
IRQ
line should be connected to the
input of the 68HC11.
DV
DV
DD
DD
SS
PC0
PC1
SMODE
RFS
TFS
68HC11
AD7890
SCK
MISO
MOSI
SCLK
The serial clock rate from the 8xC51 is limited to significantly
less than the allowable input serial clock frequency with which
the AD7890 can operate. As a result, the time to read data from
the part is actually longer than the conversion time of the part.
This means that the AD7890 cannot run at its maximum
throughput rate when used with the 8xC51.
DATA OUT
DATA IN
Figure 15. AD7890 to 68HC11 Interface
Rev. C | Page 20 of 28
AD7890
The serial clock rate from the 68HC11 is limited to significantly
less than the allowable input serial clock frequency with which
the AD7890 can operate. As a result, the time to read data from
the part is actually longer than the conversion time of the part.
This means that the AD7890 cannot run at its maximum
throughput rate when used with the 68HC11.
AD7890 TO DSP56000 INTERFACE
Figure 17 shows an interface circuit between the AD7890 and
the DSP56000 DSP processor. The AD7890 is configured for its
external clocking mode. The DSP56000 is configured for
normal mode, synchronous operation with continuous clock. It
is also set up for a 16-bit word with SCK and SC2 as outputs.
The FSL bit of the DSP56000 should be set to 0.
AD7890 TO ADSP-2101 INTERFACE
An interface circuit between the AD7890 and the ADSP-2101
DSP processor is shown in Figure 16. The AD7890 is
configured for its external clocking mode with the ADSP-2101
providing the serial clock and frame synchronization signals.
The RFS1 and TFS1 inputs and outputs are configured for
active low operation.
RFS
TFS
and inputs of the AD7890 are connected together
The
so data is transmitted to and from the AD7890 at the same time.
With the DSP56000 in synchronous mode, it provides a
common frame synchronization pulse for read and write
operations on its SC2 output. This is inverted before being
RFS
TFS
applied to the
and
inputs of the AD7890.
DV
DD
To monitor the conversion time on the AD7890, a scheme, such
CONVST
as the scheme outlined with
in the Simplifying the
SMODE
RFS
Interface section, can be used. This can be implemented by
RFS1
TFS1
CONVST
IRQA
input of the
connecting the
DSP56000.
line directly to the
TFS
ADSP-2101
SCLK1
AD7890
SCLK
DV
DD
DR1
DT1
DATA OUT
DATA IN
SMODE
RFS
SC2
Figure 16. AD7890 to ADSP-2101 Interface
TFS
DSP56000
SCK
AD7890
SCLK
In the scheme shown, the maximum serial clock frequency the
ADSP-2101 can provide is 6.25 MHz. This allows the AD7890
to be operated at a sample rate of 111 kHz. If it is desirable to
operate the AD7890 at its maximum throughput rate of
117 kHz, an external serial clock of 10 MHz can be provided
to drive the serial clock input of both the AD7890 and the
ADSP-2101.
DATA OUT
SRD
STD
DATA IN
Figure 17. AD7890 to DSP56000 Interface
AD7890 TO TMS320C25/30 INTERFACE
Figure 18 shows an interface circuit between the AD7890 and
the TMS320C25/30 DSP processor. The AD7890 is configured
for its self-clocking mode where it provides the serial clock and
frame synchronization signals. However, the TMS320C25/30
requires a continuous serial clock. In the scheme outlined here,
the AD7890’s master clock signal, CLK IN, is used to provide
the serial clock for the processor. The AD7890 output SCLK, to
which the serial data is referenced, is a delayed version of the
CLK IN signal. The typical delay between the CLK IN and
SCLK is 20 ns and is no more than 50 ns over supplies and
temperature. Therefore, there is still sufficient setup time for
DATA OUT to be clocked into the DSP on the edges of the
CLK IN signal. When writing data to the AD7890, the
To monitor the conversion time on the AD7890, a scheme, such
CONVST
as the scheme outlined with
Interface section, can be used. This can be implemented by
CONVST IRQ2
input of the
in the Simplifying the
connecting the
line directly to the
ADSP-2101. An alternative to this, where the user does not have
to worry about monitoring the conversion status, is to operate
the AD7890 in its self-clocking mode. In this scheme, the actual
interface connections would remain the same as in Figure 16,
but now the AD7890 provides the serial clock and receive frame
synchronization signals. Using the AD7890 in its self-clocking
mode limits the throughput rate of the system as the serial clock
rate is limited to 2.5 MHz.
processor’s data hold time is sufficiently long to cater for the
RFS
delay between the two clocks. The AD7890’s
signal
connects to both the FSX and FSR inputs of the processor. The
processor can generate its own FSX signal, so if required, the
RFS
TFS
interface can be modified so that the
separated and the processor generates the FSX signal which is
TFS
and
signals are
connected to the
input of the AD7890.
Rev. C | Page 21 of 28
AD7890
In the scheme outlined here, the user does not have to worry
about monitoring the end of conversion. Once conversion is
complete, the AD7890 takes care of transmitting back its
conversion result to the processor. Once the 16 bits of data have
been received by the processor into its serial shift register, it
ANTIALIASING FILTER
The AD7890 provides separate access to the multiplexer and
ADC via the MUX OUT pin and the SHA IN pin. One of the
reasons for this is to allow the user to implement an antialiasing
filter between the multiplexer and the ADC. Inserting the
antialiasing filter at this point has the advantage that one
antialiasing filter can suffice for all eight channels rather than a
separate antialiasing filter for each channel if they were to be
placed prior to the multiplexer.
RFS
TFS
generates an internal interrupt. Since the
pin and the
pin are connected together, data is transmitted to the control
register of the AD7890 whenever the AD7890 transmits its
conversion result. The user just has to ensure that the word to
be written to the AD7890 control register is set up prior to the
end of conversion. As part of the interrupt routine, which
recognizes that data has been read in, the processor can set up
the data it is going to write to the control register next time around.
The antialiasing filter inserted between the MUX OUT pin and
the SHA IN pin is generally a low-pass filter to remove high
frequency signals which could possibly be aliased back in-band
during the sampling process. It is recommended that this filter
is an active filter, ideally with the MUX OUT pin of the AD7890
driving a high impedance stage and the SHA IN pin of the part
being driven from a low impedance stage. This removes any
effects from the variation of the part’s multiplexer on-resistance
with input signal voltage, and removes any effects of a high
source impedance at the sampling input of the track/hold. With
an external antialiasing filter in place, the additional settling
time associated with the filter should be accounted for by using
CLK INPUT
CLK IN
TMS320C25/C30
FSR
SMODE
RFS
FSX
CLKX
CLKR
DR
TFS
AD7890
SCLK
a larger capacitance on CEXT
.
DATA OUT
DATA IN
DX
Figure 18. AD7890 to TMS320C25/30 Interface
Rev. C | Page 22 of 28
AD7890
PERFORMANCE
LINEARITY
are achieved with a serial clock rate of 2.5 MHz. If a higher
serial clock rate is used, the code transition noise degrades from
that shown in the plot in Figure 20. This has the effect of
injecting noise onto the die while bit decisions are being made,
increasing the noise generated by the AD7890. The histogram
plot for 8192 conversions of the same dc input now shows a
larger spread of codes with the rms noise for the AD7890-2
increasing to 170 μV. This effect varies depending on where the
serial clock edges appear with respect to the bit trials of the
conversion process.
The linearity of the AD7890 is primarily determined by the on-
chip 12-bit D/A converter. This is a segmented DAC that is laser
trimmed for 12-bit integral linearity and differential linearity.
Typical relative numbers for the part are 1/4 LSB while the
typical DNL errors are 1/2 LSB.
NOISE
In an ADC, noise exhibits itself as code uncertainty in dc
applications and as the noise floor (in an FFT, for example) in ac
applications. In a sampling ADC like the AD7890, all information
about the analog input appears in the baseband from dc to 1/2 the
sampling frequency. The input bandwidth of the track/hold exceeds
the Nyquist bandwidth and, therefore, an antialiasing filter should
be used to remove unwanted signals above fS/2 in the input signal
in applications where such signals exist.
It is possible to achieve the same level of performance when
reading during conversion as when reading after conversion,
depending on the relationship of the serial clock edges to the bit
trial points (for example, the relationship of the serial clock
edges to the CLK IN edges). The bit decision points on the
AD7890 are on the falling edges of the master clock (CLK IN)
during the conversion process. Clocking out new data bits at
these points (for example, the rising edge of SCLK) is the most
critical from a noise standpoint. The most critical bit decisions
are the MSBs, so to achieve the level of performance outlined in
Figure 19 shows a histogram plot for 8192 conversions of a dc
input using the AD7890. The analog input was set at the center
of a code transition. The timing and control sequence used was
as per Figure 7 where the optimum performance of the ADC is
achieved. The same performance can be achieved in self-
clocking mode where the part transmits its data after
CONVST
Figure 20, reading within 1 μs after the rising edge of
should be avoided.
8000
conversion is complete. Almost all of the codes appear in the
one output bin indicating very good noise performance from
the ADC. The rms noise performance for the AD7890-2 for the
plot in Figure 19 was 81 μV. Since the analog input range, and
hence LSB size, on the AD7893-4 is 1.638 times what it is for
the AD7893-2, the same output code distribution results in an
output rms noise of 143 μV for the AD7893-4. For the AD7890-10,
with an LSB size eight times that of the AD7890-2, the code
distribution represents an output rms noise of 648 μV.
SAMPLING
FREQUENCY = 102.4kHz
7000
6000
5000
T
= 25°C
A
4000
3000
2000
1000
0
9000
SAMPLING FREQUENCY = 102.4kHz
T
= 25°C
8000
7000
6000
5000
4000
3000
2000
1000
A
(X–4) (X–3) (X–2) (X–1)
X
(X+1) (X+2) (X+3) (X+4)
CODE
Figure 20. Histogram of 8192 Conversions with Read During Conversion
Writing data to the control register also has the effect of
introducing digital activity onto the part while conversion is in
progress. However, since there are no output drivers active
during a write operation, the amount of current flowing on the
die is less than for a read operation. Therefore, the amount of
noise injected into the die is less than for a read operation.
Figure 21 shows the effect of a write operation during
conversion. The histogram plot for 8192 conversions of the
same dc input now shows a larger spread of codes than for ideal
conditions but smaller than for a read operation. The resulting
rms noise for the AD7890-2 is 110 μV. In this case, the serial
clock frequency is 10 MHz.
0
(X–4) (X–3) (X–2) (X–1)
X
(X+1) (X+2) (X+3) (X+4)
CODE
Figure 19. Histogram of 8192 Conversions of a DC Input
In the external clocking mode, it is possible to write data to the
control register or read data from the output register while a
conversion is in progress. The same data is presented in
Figure 20 as in Figure 19, except that in Figure 20, the output
data read for the device occurs during conversion. These results
Rev. C | Page 23 of 28
AD7890
8000
0
SAMPLE RATE = 102.4kHz
INPUT FREQUENCY = 10kHz
SNR = 71.5dB
SAMPLING
FREQUENCY = 102.4kHz
7000
T
= 25°C
A
T
= 25°C
A
30
6000
5000
60
90
4000
3000
2000
1000
0
120
0
25.6
51.2
(X–4) (X–3) (X–2) (X–1)
X
(X+1) (X+2) (X+3) (X+4)
FREQUENCY (kHz)
CODE
Figure 22. AD7890 FFT Plot
Figure 21. Histogram of 8192 Conversions with Write During Conversion
EFFECTIVE NUMBER OF BITS
DYNAMIC PERFORMANCE
The formula for signal to (noise + distortion) ratio (see the
Terminology section) is related to the resolution or number of
bits in the converter. Rewriting the formula provides a measure
of performance expressed in effective number of bits (N):
The AD7890 contains an on-chip track/hold, allowing the part
to sample input signals up to 50 kHz on any of its input
channels. Many AD7890 applications simply require it to
sequence through low frequency input signals across its eight
channels. There may be some applications, however, for which
the dynamic performance of the converter out to 40 kHz input
frequency is of interest. For these wider band sampling
applications, it is recommended that the hardware conversion
start method is used.
N = (SNR — 1.76)/6.02
where SNR is signal to (noise + distortion) ratio.
The effective number of bits for a device can be calculated from
its measured signal to (noise + distortion) ratio. Figure 23
shows a typical plot of effective number of bits versus frequency
for the AD7890-2 from dc to 40 kHz. The sampling frequency is
102.4 kHz. The plot shows that the AD7890 converts an input
sine wave of 40 kHz to an effective numbers of bits of 11 which
equates to a signal to (noise + distortion) level of 68 dB.
These applications require information on the ADC’s effect on
the spectral content of the input signal. Signal to (noise +
distortion), total harmonic distortion, peak harmonic or
spurious and intermodulation distortion are all specified.
Figure 22 shows a typical FFT plot of a 10 kHz, 0 V to 2.5 V
input after being digitized by the AD7890-2 operating at a
102.4 kHz sampling rate. The signal to (noise + distortion) is
71.5 dB and the total harmonic distortion is −85 dB. Note that
reading data from the part during conversion at 10 MHz serial
clock does have a significant impact on dynamic performance.
For sampling applications, it is therefore recommended not to
read data during conversion.
12.0
11.5
11.0
10.5
10.0
0
20
40
INPUT FREQUENCY (kHz)
Figure 23. Effective Number of Bits vs. Frequency
Rev. C | Page 24 of 28
AD7890
OUTLINE DIMENSIONS
1.280 (32.51)
1.250 (31.75)
1.230 (31.24)
24
1
13
12
0.280 (7.11)
0.250 (6.35)
0.240 (6.10)
0.325 (8.26)
0.310 (7.87)
0.300 (7.62)
0.100 (2.54)
BSC
0.060 (1.52)
MAX
0.195 (4.95)
0.130 (3.30)
0.115 (2.92)
0.210 (5.33)
MAX
0.015
(0.38)
MIN
0.150 (3.81)
0.130 (3.30)
0.115 (2.92)
0.015 (0.38)
GAUGE
0.014 (0.36)
0.010 (0.25)
0.008 (0.20)
PLANE
SEATING
PLANE
0.022 (0.56)
0.018 (0.46)
0.014 (0.36)
0.430 (10.92)
MAX
0.005 (0.13)
MIN
0.070 (1.78)
0.060 (1.52)
0.045 (1.14)
COMPLIANT TO JEDEC STANDARDS MS-001
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
CORNER LEADS MAY BE CONFIGURED AS WHOLE OR HALF LEADS.
Figure 24. 24-Lead Plastic Dual In-Line Package [PDIP]
Narrow Body
(N-24-1)
Dimensions shown in inches and (millimeters)
0.098 (2.49)
MAX
0.005 (0.13)
MIN
0.310 (7.87)
0.220 (5.59)
24
13
12
1
PIN 1
0.060 (1.52)
0.015 (0.38)
0.320 (8.13)
0.200 (5.08)
1.280 (32.51) MAX
MAX
0.290 (7.37)
0.150 (3.81)
MIN
0.015 (0.38)
0.008 (0.20)
15°
0°
0.200 (5.08)
0.125 (3.18)
SEATING
PLANE
0.100
(2.54)
BSC
0.070 (1.78)
0.030 (0.76)
0.023 (0.58)
0.014 (0.36)
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 25. 24-Lead Ceramic Dual In-Line Package [CERDIP]
(Q-24)
Dimensions shown in inches and (millimeters)
Rev. C | Page 25 of 28
AD7890
15.60 (0.6142)
15.20 (0.5984)
24
1
13
12
7.60 (0.2992)
7.40 (0.2913)
10.65 (0.4193)
10.00 (0.3937)
0.75 (0.0295)
0.25 (0.0098)
45°
2.65 (0.1043)
2.35 (0.0925)
0.30 (0.0118)
0.10 (0.0039)
8°
0°
COPLANARITY
0.10
SEATING
PLANE
0.51 (0.0201)
0.31 (0.0122)
1.27 (0.0500)
BSC
1.27 (0.0500)
0.40 (0.0157)
0.33 (0.0130)
0.20 (0.0079)
COMPLIANT TO JEDEC STANDARDS MS-013-AD
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 26. 24-Lead Standard Small Outline Package [SOIC_W]
Wide Body
(RW-24)
Dimensions shown in millimeters and( inches)
Rev. C | Page 26 of 28
AD7890
ORDERING GUIDE
Model
AD7890AN-2
AD7890ANZ-21
AD7890BN-2
AD7890BNZ-21
AD7890AR-2
AD7890AR-2REEL
AD7890ARZ-21
AD7890ARZ-2REEL1
AD7890BR-2
AD7890BR-2REEL
AD7890BRZ-21
AD7890BRZ-2REEL1
AD7890SQ-2
AD7890AN-4
AD7890ANZ-41
AD7890BN-4
AD7890BNZ-41
AD7890AR-4
AD7890AR-4REEL
AD7890ARZ-41
AD7890ARZ-4REEL1
AD7890BR-4
AD7890BR-4REEL
AD7890BRZ-41
AD7890BRZ-4REEL1
AD7890SQ-4
AD7890AN-10
AD7890ANZ-101
AD7890BN-10
AD7890BNZ-101
AD7890AR-10
AD7890AR-10REEL
AD7890ARZ-101
AD7890ARZ-10REEL1
AD7890BR-10
AD7890BR-10REEL
AD7890BRZ-101
AD7890BRZ-10REEL1
AD7890SQ-10
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−55°C to +125°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−55°C to +125°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−55°C to +125°C
Package Description
24-Lead PDIP
24-Lead PDIP
24-Lead PDIP
24-Lead PDIP
24-Lead SOIC_W
24-Lead SOIC_W
24-Lead SOIC_W
24-Lead SOIC_W
24-Lead SOIC_W
24-Lead SOIC_W
24-Lead SOIC_W
24-Lead SOIC_W
24-Lead CERDIP
24-Lead PDIP
Linearity Error
1 LSB
1 LSB
1/2 LSB
1/2 LSB
1 LSB
1 LSB
1 LSB
1 LSB
1/2 LSB
1/2 LSB
1/2 LSB
1/2 LSB
1 LSB
1 LSB
1 LSB
1/2 LSB
1/2 LSB
1 LSB
1 LSB
1 LSB
1 LSB
1/2 LSB
1/2 LSB
1/2 LSB
1/2 LSB
1 LSB
1 LSB
1 LSB
1/2 LSB
1/2 LSB
1 LSB
1 LSB
1 LSB
1 LSB
Package Option
N-24-1
N-24-1
N-24-1
N-24-1
RW-24
RW-24
RW-24
RW-24
RW-24
RW-24
RW-24
RW-24
Q-24
N-24
N-24
N-24
N-24
24-Lead PDIP
24-Lead PDIP
24-Lead PDIP
24-Lead SOIC_W
24-Lead SOIC_W
24-Lead SOIC_W
24-Lead SOIC_W
24-Lead SOIC_W
24-Lead SOIC_W
24-Lead SOIC_W
24-Lead SOIC_W
24-Lead CERDIP
24-Lead PDIP
RW-24
RW-24
RW-24
RW-24
RW-24
RW-24
RW-24
RW-24
Q-24
N-24-1
N-24-1
N-24-1
N-24-1
RW-24
RW-24
RW-24
RW-24
RW-24
RW-24
RW-24
RW-24
Q-24
24-Lead PDIP
24-Lead PDIP
24-Lead PDIP
24-Lead SOIC_W
24-Lead SOIC_W
24-Lead SOIC_W
24-Lead SOIC_W
24-Lead SOIC_W
24-Lead SOIC_W
24-Lead SOIC_W
24-Lead SOIC_W
24-Lead CERDIP
1/2 LSB
1/2 LSB
1/2 LSB
1/2 LSB
1 LSB
1 Z = Pb-free part.
Rev. C | Page 27 of 28
AD7890
NOTES
©2006 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
C01357-0-9/06(C)
Rev. C | Page 28 of 28
相关型号:
AD7890BRZ-4
8-CH 12-BIT PROPRIETARY METHOD ADC, SERIAL ACCESS, PDSO24, LEAD FREE, MS-013AD, SOIC-24
ROCHESTER
AD7890SQ-4
8-CH 12-BIT PROPRIETARY METHOD ADC, SERIAL ACCESS, CDIP24, 0.300 INCH, CERDIP-24
ROCHESTER
AD7890SR
IC 12-BIT CONVERTER SUBSYSTEM ADC, SERIAL ACCESS, PDSO24, SOIC-24, Analog to Digital Converter
ADI
©2020 ICPDF网 联系我们和版权申明