AD7985BCPZ-RL7 [ADI]
16-Bit, 2.5 MSPS, PulSAR 15.5 mW ADC in LFCSP; 16位， 2.5 MSPS ， 15.5的PulSAR ADC毫瓦的LFCSP
| 型号： | AD7985BCPZ-RL7 |
| 厂家： | 
ADI |
| 描述： | 16-Bit, 2.5 MSPS, PulSAR 15.5 mW ADC in LFCSP |
| 文件： | 总28页 (文件大小：586K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
16-Bit, 2.5 MSPS, PulSAR
15.5 mW ADC in LFCSP
AD7985
APPLICATION DIAGRAM
FEATURES
1.8V
TO
16-bit resolution with no missing codes
Throughput: 2.5 MSPS (TURBO high), 2.0 MSPS (TURBO low)
Low power dissipation
15.5 mW at 2.5 MSPS, with external reference
28 mW at 2.5 MSPS, with internal reference
INL: 0.7 LSB typical, 1.5 LSB maximum
SNR
5V
2.5V
2.7V
VIO
TURBO
SDI
BVDD
AVDD,
DVDD
0V
TO
VIO
IN+
IN–
3- OR 4-WIRE
INTERFACE:
SPI, CS,
DAISY CHAIN
(TURBO = LOW)
V
REF
AD7985
SCK
SDO
CNV
GND REF
88.5 dB, with on-chip reference
90 dB, with external reference
10µF
4.096 V internal reference: typical drift of 10 ppm/°C
Pseudo differential analog input voltage range
0 V to VREF with VREF up to 5.0 V
NOTES
1. GND REFERS TO REFGND, AGND, AND DGND.
Allows use of any input range
Figure 1.
No pipeline delay
Logic interface: 1.8 V/2.5 V/2.7 V
GENERAL DESCRIPTION
The AD7985 is a 16-bit, 2.5 MSPS successive approximation
analog-to-digital converter (SAR ADC). It contains a low power,
high speed, 16-bit sampling ADC, an internal conversion clock,
an internal reference (and buffer), error correction circuits, and
a versatile serial interface port. On the rising edge of CNV, the
AD7985 samples an analog input, IN+, between 0 V and REF
with respect to a ground sense, IN−. The AD7985 features a
very high sampling rate turbo mode (TURBO is high) and a
reduced power normal mode (TURBO is low) for low power
applications where the power is scaled with the throughput.
Serial interface: SPI-/QSPI™-/MICROWIRE™-/DSP-compatible
Ability to daisy-chain multiple ADCs with busy indicator
20-lead, 4 mm × 4 mm LFCSP (QFN)
APPLICATIONS
Battery-powered equipment
Communications
ATE
Data acquisition systems
Medical instruments
In normal mode (TURBO is low), the SPI-compatible serial inter-
face also features the ability, using the SDI input, to daisy-chain
several ADCs on a single 3-wire bus and provide an optional busy
indicator. It is compatible with 1.8 V, 2.5 V, and 2.7 V supplies
using the separate VIO supply.
The AD7985 is available in a 20-lead LFCSP with operation
specified from −40°C to +85°C.
Table 1. MSOP, LFCSP, 14-/16-/18-Bit PulSAR® ADCs1
Type
14-Bit
16-Bit
100 kSPS
AD7940
AD7680
AD7683
AD7684
250 kSPS
AD79422
AD76852
AD76872
AD7694
400 kSPS to 500 kSPS
AD79462
≥1000 kSPS
ADC Driver
AD76862
AD79802
AD79832
AD79853
AD79822
AD79842
AD79863
ADA4941-1
ADA4841-x
AD8021
ADA4941-1
ADA4841-x
AD8021
AD76882
AD76932
18-Bit
AD76912
AD76902
1 See www.analog.com for the latest selection of PulSAR ADCs and ADC drivers.
2 Pin-for-pin compatible with all other parts marked with this endnote.
3 The AD7985 and AD7986 are pin-for-pin compatible.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
©2009 Analog Devices, Inc. All rights reserved.
AD7985
TABLE OF CONTENTS
Features .............................................................................................. 1
Analog Inputs ............................................................................. 15
Driver Amplifier Choice ........................................................... 15
Voltage Reference Input ............................................................ 16
Power Supply............................................................................... 16
Digital Interface.............................................................................. 17
Data Reading Options ............................................................... 18
Applications....................................................................................... 1
Application Diagram........................................................................ 1
General Description......................................................................... 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
Timing Specifications .................................................................. 5
Absolute Maximum Ratings............................................................ 6
ESD Caution.................................................................................. 6
Pin Configuration and Function Descriptions............................. 7
Typical Performance Characteristics ............................................. 9
Terminology .................................................................................... 12
Theory of Operation ...................................................................... 13
Circuit Information.................................................................... 13
Converter Operation.................................................................. 13
Conversion Modes of Operation.............................................. 13
Typical Connection Diagram ................................................... 14
CS
CS
CS
CS
Mode, 3-Wire Without Busy Indicator ............................. 19
Mode, 3-Wire with Busy Indicator .................................... 20
Mode, 4-Wire Without Busy Indicator ............................. 21
Mode, 4-Wire with Busy Indicator .................................... 22
Chain Mode Without Busy Indicator...................................... 23
Chain Mode with Busy Indicator............................................. 24
Applications Information.............................................................. 25
Layout .......................................................................................... 25
Evaluating AD7985 Performance............................................. 25
Outline Dimensions....................................................................... 27
Ordering Guide .......................................................................... 27
REVISION HISTORY
9/09—Revision 0: Initial Version
Rev. 0 | Page 2 of 28
AD7985
SPECIFICATIONS
AVDD = DVDD = 2.5 V, BVDD = 5 V, VIO = 1.8 V to 2.7 V, VREF = 4.096 V, TA = −40°C to +85°C, unless otherwise noted.
Table 2.
Parameter
Test Conditions/Comments
Min
Typ
Max
Unit
RESOLUTION
16
Bits
ANALOG INPUT
Voltage Range
Absolute Input Voltage
(IN+) − (IN−)
IN+
IN−
0
−0.1
−0.1
VREF
VREF + 0.1
+0.1
V
V
V
Leakage Current at 25°C
Input Impedance
Acquisition phase
250
nA
See the Analog Inputs section
ACCURACY
No Missing Codes
16
−0.99
−1.50
Bits
LSB1
LSB1
LSB1
LSB1
Differential Nonlinearity Error, DNL
Integral Nonlinearity Error, INL
Transition Noise
0.50
0.7
0.8
+0.99
+1.50
2
Gain Error, TMIN to TMAX
−15
2
+15
Gain Error Temperature Drift
Zero Error, TMIN to TMAX
0.8
0.08
ppm/°C
mV
2
−0.99
+0.99
Zero Temperature Drift
Power Supply Sensitivity
THROUGHPUT
Conversion Rate
Transient Response
AC ACCURACY
0.55
90
ppm/°C
dB3
AVDD = 2.5 V 5%
Full-scale step
0
2.5
100
MSPS
ns
Dynamic Range
VREF = 4.096 V, internal reference
VREF = 5.0 V, external reference
fIN = 20 kHz, VREF = 4.096 V, internal 87.0
reference
fIN = 20 kHz, VREF = 5.0 V, external
reference
87.5
89.0
89
90
88.5
dB3
dB3
dB3
Signal-to-Noise Ratio, SNR
89.0
90.0
dB3
Spurious-Free Dynamic Range, SFDR
Total Harmonic Distortion4, THD
fIN = 20 kHz
fIN = 20 kHz, VREF = 4.096 V, internal
reference
103
−100
dB3
dB3
Signal-to-Noise-and-Distortion Ratio,
SINAD
fIN = 20 kHz, VREF = 4.096 V
90.5
dB3
SAMPLING DYNAMICS
−3 dB Input Bandwidth
Aperture Delay
19
0.7
MHz
ns
1 LSB means least significant bit. With the 4.096 V input range, one LSB is 62.5 μV.
2 See the Terminology section. These specifications include full temperature range variation but not the error contribution from the external reference.
3 All specifications expressed in decibels are referred to a full-scale input FSR and tested with an input signal at 0.5 dB below full scale, unless otherwise specified.
4 Tested fully in production at fIN = 1 kHz.
Rev. 0 | Page 3 of 28
AD7985
Table 3.
Parameter
Test Conditions/Comments
PDREF is low
TA = 25°C
Min
Typ
Max
Unit
INTERNAL REFERENCE
Output Voltage
Temperature Drift
Line Regulation
Turn-On Settling Time
REFIN Output Voltage
REFIN Output Resistance
EXTERNAL REFERENCE
Voltage Range
Current Drain
REFERENCE BUFFER
REFIN Input Voltage Range
REFIN Input Current
DIGITAL INPUTS
Logic Levels
4.081
4.096
10
50
40
1.2
6
4.111
V
−40°C to +85°C
ppm/°C
ppm/V
ms
V
kΩ
AVDD = 2.5 V 5%
CREF = 10 ꢀF, CREFIN = 0.1 ꢀF
REFIN at 25°C
PDREF is high, REFIN is low
2.4
5.1
V
μA
500
1.2
160
V
μA
VIL
VIH
IIL
IIH
−0.3
0.9 × VIO
−1
0.1 × VIO
VIO + 0.3
+1
V
V
μA
μA
−1
+1
DIGITAL OUTPUTS
Data Format
Serial 16 bits, straight binary
Pipeline Delay
Conversion results available immediately
after completed conversion
VOL
VOH
ISINK = +500 μA
ISOURCE = −500 μA
0.4
V
V
VIO − 0.3
POWER SUPPLIES
AVDD, DVDD
BVDD
2.375
4.75
1.8
2.5
5.0
2.5
1.0
2.625
5.25
2.7
V
V
V
μA
VIO
Specified performance
AVDD = DVDD = VIO = 2.5 V
Standby Current1, 2
Power Dissipation
With Internal Reference
2.5 MSPS throughput
2.0 MSPS throughput
2.5 MSPS throughput
2.0 MSPS throughput
28
25
15.5
12
33
30
17
13
mW
mW
mW
mW
With External Reference
TEMPERATURE RANGE3
Specified Performance
TMIN to TMAX
−40
+85
°C
1 With all digital inputs forced to VIO or GND as required.
2 During acquisition phase.
3 Contact an Analog Devices, Inc., sales representative for the extended temperature range.
Rev. 0 | Page 4 of 28
AD7985
TIMING SPECIFICATIONS
AVDD = DVDD = 2.5 V, BVDD = 5 V, VIO = 1.8 V to 2.7 V, VREF = 4.096 V, TA = −40°C to +85°C, unless otherwise noted.1
Table 4.
Parameter
Symbol
Test Conditions/Comments
Min
Typ
Max
Unit
Conversion Time: CNV Rising Edge
to Data Available
tCONV
Turbo mode/normal mode
320/420
ns
Acquisition Time
Time Between Conversions
CNV Pulse Width
tACQ
tCYC
tCNVH
tDATA
tQUIET
80
400/500
10
ns
ns
ns
Turbo mode/normal mode
CS mode
Data Read During Conversion
Quiet Time During Acquisition from Last SCK
Falling Edge to CNV Rising Edge
Turbo mode/normal mode
190/290
ns
ns
20
SCK Period
tSCK
CS mode
9
ns
ns
ns
ns
ns
ns
ns
ns
tSCK
Chain mode
11
3.5
3.5
2
SCK Low Time
SCK High Time
tSCKL
tSCKH
tHSDO
tDSDO
tEN
SCK Falling Edge to Data Remains Valid
SCK Falling Edge to Data Valid Delay
CNV or SDI Low to SDO D15 MSB Valid
CNV or SDI High or Last SCK Falling Edge
to SDO High Impedance
4
5
8
tDIS
CS mode
SDI Valid Setup Time from CNV Rising Edge
SDI Valid Hold Time from CNV Rising Edge
tSSDICNV
tHSDICNV
tHSDICNV
tSSCKCNV
tHSCKCNV
tSSDISCK
tHSDISCK
tDSDOSDI
4
0
0
5
5
2
3
ns
ns
ns
ns
ns
ns
ns
ns
CS mode
Chain mode
Chain mode
Chain mode
Chain mode
Chain mode
Chain mode with busy indicator
SCK Valid Setup Time from CNV Rising Edge
SCK Valid Hold Time from CNV Rising Edge
SDI Valid Setup Time from SCK Falling Edge
SDI Valid Hold Time from SCK Falling Edge
SDI High to SDO High
15
1 See Figure 2 and Figure 3 for load conditions.
10% VIO
500µA
I
OL
90% VIO
tDELAY
tDELAY
1
V
1
V
IH
IH
1.4V
TO SDO
1
1
V
V
IL
IL
C
L
20pF
1
MINIMUM V AND MAXIMUM V USED. SEE DIGITAL INPUTS
IH
IL
SPECIFICATIONS IN TABLE 3.
500µA
I
OH
Figure 2. Load Circuit for Digital Interface Timing
Figure 3. Voltage Levels for Timing
Rev. 0 | Page 5 of 28
AD7985
ABSOLUTE MAXIMUM RATINGS
Table 5.
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Parameter
Rating
Analog Inputs
IN+, IN− to GND1
−0.3 V to VREF + 0.3 V
or 130 mA
Supply Voltage
REF, BVDD to GND, REFGND
AVDD, DVDD, VIO to GND
AVDD, DVDD to VIO
−0.3 V to +6.0 V
−0.3 V to +2.7 V
−6 V to +3 V
ESD CAUTION
Digital Inputs to GND
Digital Outputs to GND
Storage Temperature Range
Junction Temperature
θJA Thermal Impedance
20-Lead LFCSP (QFN)
Lead Temperatures
−0.3 V to VIO + 0.3 V
−0.3 V to VIO + 0.3 V
−65°C to +150°C
150°C
30.4°C/W
Vapor Phase (60 sec)
Infrared (15 sec)
215°C
220°C
1 See the Analog Inputs section for an explanation of IN+ and IN−.
Rev. 0 | Page 6 of 28
AD7985
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
PIN 1
INDICATOR
REF
REF
REFGND
REFGND
IN–
1
2
3
4
5
15 TURBO
14 SDI
13 CNV
12 SCK
11 DVDD
AD7985
TOP VIEW
(Not to Scale)
NOTES
1. THE EXPOSED PAD IS NOT CONNECTED
INTERNALLY. FOR INCREASED
RELIABILITY OF THE SOLDER JOINTS, IT
IS RECOMMENDED THAT THE PAD BE
SOLDERED TO THE SYSTEM
GROUND PLANE.
Figure 4. Pin Configuration
Table 6. Pin Function Descriptions
Pin No.
Mnemonic
Type1 Description
1, 2
REF
AI
Reference Output/Input Voltage.
When PDREF is low, the internal reference and buffer are enabled, producing 4.096 V on this pin.
When PDREF is high, the internal reference and buffer are disabled, allowing an externally supplied
voltage reference up to 5.0 V.
Decoupling is required with or without the internal reference and buffer. This pin is referred to the
REFGND pins and should be decoupled closely to the REFGND pins with a 10 μF capacitor.
3, 4
5
6
REFGND
IN−
IN+
AI
AI
AI
Reference Input Analog Ground.
Analog Input Ground Sense. Connect this pin to the analog ground plane or to a remote ground sense.
Analog Input. This pin is referred to IN−. The voltage range, that is, the difference between IN+ and IN−,
is 0 V to VREF
.
7
8
PDREF
VIO
DI
P
Internal Reference Power-Down Input. When this pin is low, the internal reference is enabled. When
this pin is high, the internal reference is powered down and an external reference must be used.
Input/Output Interface Digital Power. Nominally at the same supply voltage as the host interface
(1.8 V, 2.5 V, or 2.7 V).
9
SDO
DO
P
P
DI
DI
Serial Data Output. The conversion result is output on this pin. It is synchronized to SCK.
Digital Power Ground.
Digital Power. Nominally at 2.5 V.
10
11
12
13
DGND
DVDD
SCK
Serial Data Clock Input. When the part is selected, the conversion result is shifted out by this clock.
CNV
Convert Input. This input has multiple functions. On its leading edge, it initiates the conversions
and selects the interface mode of the part: chain mode or CS mode. In CS mode, the SDO pin is
enabled when CNV is low. In chain mode, the data should be read when CNV is high.
14
SDI
DI
Serial Data Input. This input has multiple functions. It selects the interface mode of the ADC as follows.
Chain mode is selected if SDI is low during the CNV rising edge. In chain mode, SDI is used as a data
input to daisy-chain the conversion results of two or more ADCs onto a single SDO line. The digital data
level on SDI is output on SDO with a delay of 16 SCK cycles.
CS mode is selected if SDI is high during the CNV rising edge. In CS mode, either SDI or CNV can enable
the serial output signals when low. If SDI or CNV is low when the conversion is complete, the busy
indicator feature is enabled.
15
TURBO
DI
Conversion Mode Selection. When TURBO is high, the maximum throughput (2.5 MSPS) is achieved,
and the ADC does not power down between conversions. When TURBO is low, the maximum throughput
is lower (2.0 MSPS), and the ADC powers down between conversions.
16
17, 18
AVDD
AGND
P
P
Input Analog Power. Nominally at 2.5 V.
Analog Power Ground.
Rev. 0 | Page 7 of 28
AD7985
Pin No.
Mnemonic
Type1 Description
19
BVDD
P
Reference Buffer Power. Nominally at 5.0 V. If an external reference buffer is used to achieve the maximum
SNR performance with a 5 V reference, the reference buffer must be powered down by connecting the
REFIN pin to ground. The external reference buffer must be connected to the BVDD pin.
20
REFIN
AI/O
Internal Reference Output/Reference Buffer Input.
When PDREF is low, the internal band gap reference produces a 1.2 V (typical) voltage on this pin,
which needs external decoupling (0.1 μF typical).
When PDREF is high, use an external reference to provide 1.2 V (typical) to this pin.
When PDREF is high and REFIN is low, the on-chip reference buffer and the band gap reference are
powered down. An external reference must be connected to REF and BVDD.
21
Exposed Pad
EP
The exposed pad is not connected internally. For increased reliability of the solder joints, it is
recommended that the pad be soldered to the system ground plane.
1 AI = analog input, AI/O = bidirectional analog, DI = digital input, DO = digital output, and P = power.
Rev. 0 | Page 8 of 28
AD7985
TYPICAL PERFORMANCE CHARACTERISTICS
AVDD = DVDD = VIO = 2.5 V, BVDD = 5.0 V, VREF = 5.0 V, external reference (PDREF is high, REFIN is low), unless otherwise noted.
1.25
1.00
0.75
0.50
0.25
0
1.00
0.75
0.50
0.25
0
POSITIVE INL = +0.38LSB
NEGATIVE INL = –0.46LSB
POSITIVE DNL = +0.19LSB
NEGATIVE DNL = –0.20LSB
–0.25
–0.50
–0.75
–1.00
–1.25
–0.25
–0.50
–0.75
–1.00
0
16,384
32,768
CODE
49,152
65,536
0
16,384
32,768
CODE
49,152
65,536
Figure 5. Integral Nonlinearity vs. Code
Figure 8. Differential Nonlinearity vs. Code
60,000
50,000
40,000
30,000
20,000
10,000
0
60,000
50,000
40,000
30,000
20,000
10,000
0
57,138
53,522
48,730
38,843
26,249
15,645
11,888
6150
2537
800
479
122
0
2
6
0
0
33
0
7FFC 7FFD 7FFE 7FFF 8000 8001 8002 8003 8004
CODE IN HEX
7FFB 7FFC 7FFD 7FFE 7FFF 8000 8001 8002 8003 8004
CODE IN HEX
Figure 6. Histogram of DC Input at Code Center (External Reference)
Figure 9. Histogram of DC Input at Code Transition (External Reference)
60,000
50,000
46,649
43,622
45,000
49,585
50,000
40,000
35,000
30,000
25,000
40,000
33,064
31,957
30,000
20,000
20,474
20,000
15,598
15,000
10,000
8455
10,000
7024
5000
2947
1662
565
403
0
11
8
0
90
0
30
0
0
0
7FFB 7FFC 7FFD 7FFE 7FFF 8000 8001 8002 8003 8004 8005
CODE IN HEX
7FFC 7FFD 7FFE 7FFF 8000 8001 8002 8003 8004 8005
CODE IN HEX
Figure 7. Histogram of DC Input at Code Center (Internal Reference)
Figure 10. Histogram of DC Input at Code Transition (Internal Reference)
Rev. 0 | Page 9 of 28
AD7985
0
0
–20
fS = 2.5MSPS
fIN = 20kHz
SNR = 89.87dB
THD = –102.76dB
SINAD = 89.66dB
fS = 2.5MSPS
fIN = 20kHz
SNR = 88.45dB
THD = –103.42dB
SINAD = 88.32dB
–20
–40
–40
–60
–60
–80
–80
–100
–120
–140
–160
–100
–120
–140
–160
–180
–180
0
250
500
750
1000
1250
0
250
500
750
1000
1250
FREQUENCY (kHz)
FREQUENCY (kHz)
Figure 11. FFT Plot (External Reference)
Figure 14. FFT Plot (Internal Reference)
100
95
16
15
14
13
12
–90
100
95
90
85
80
–95
–100
–105
–110
SFDR
ENOB
SNR
90
SINAD
85
THD
80
2.50 2.75 3.00 3.25 3.50 3.75 4.00 4.25 4.50 4.75 5.00
2.50 2.75 3.00 3.25 3.50 3.75 4.00 4.25 4.50 4.75 5.00
REFERENCE VOLTAGE (V)
REFERENCE VOLTAGE (V)
Figure 12. SNR, SINAD, and ENOB vs. Reference Voltage
Figure 15. THD and SFDR vs. Reference Voltage
95
90
85
80
75
70
65
–85
–90
–95
–100
–105
–110
1
10
100
1000
1
10
100
1000
FREQUENCY (kHz)
FREQUENCY (kHz)
Figure 13. SINAD vs. Frequency
Figure 16. THD vs. Frequency
Rev. 0 | Page 10 of 28
AD7985
95
94
93
92
91
90
89
88
87
86
85
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
I
AVDD
I
BVDD
I
REF
–10
–9
–8
–7
–6
–5
–4
–3
–2
–1
0
–55
–35
–15
5
25
45
65
85
105
125
INPUT LEVEL (dBFS)
TEMPERATURE (°C)
Figure 17. SNR vs. Input Level
Figure 19. Operating Current vs. Temperature
2.0
14
12
10
8
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
I
AVDD
I
DVDD
I
VIO
6
I
BVDD
4
I
REF
I
+ I
DVDD
+ I
VIO
AVDD
2
0
2.375
2.425
2.475
2.525
2.575
2.625
–55
–35
–15
5
25
45
65
85
105
125
AVDD AND DVDD VOLTAGE (V)
TEMPERATURE (°C)
Figure 18. Operating Current vs. Supply Voltage
Figure 20. Power-Down Current vs. Temperature
Rev. 0 | Page 11 of 28
AD7985
TERMINOLOGY
Aperture Delay
Noise-Free Code Resolution
Aperture delay is the measure of the acquisition performance
and is the time between the rising edge of the CNV input and
when the input signal is held for a conversion.
Noise-free code resolution is the number of bits beyond which it
is impossible to distinctly resolve individual codes. It is expressed
in bits and is calculated as follows:
Differential Nonlinearity Error (DNL)
Noise-Free Code Resolution = log2(2N/Peak-to-Peak Noise)
In an ideal ADC, code transitions are 1 LSB apart. DNL is the
maximum deviation from this ideal value. It is often specified in
terms of resolution for which no missing codes are guaranteed.
Signal-to-Noise Ratio (SNR)
SNR is the ratio of the rms value of the actual input signal to
the rms sum of all other spectral components below the Nyquist
frequency, excluding harmonics and dc. The value for SNR is
expressed in decibels.
Dynamic Range
Dynamic range is the ratio of the rms value of the full scale to
the total rms noise measured with the inputs shorted together.
The value for dynamic range is expressed in decibels. It is mea-
sured with a signal at −60 dBFS so that it includes all noise
sources and DNL artifacts.
Signal-to-Noise-and-Distortion Ratio (SINAD)
SINAD is the ratio of the rms value of the actual input signal to
the rms sum of all other spectral components below the Nyquist
frequency, including harmonics but excluding dc. The value for
SINAD is expressed in decibels.
Effective Number of Bits (ENOB)
ENOB is a measurement of the resolution with a sine wave
input. It is expressed in bits and is related to SINAD as follows:
Spurious-Free Dynamic Range (SFDR)
SFDR is the difference, in decibels (dB), between the rms
amplitude of the input signal and the peak spurious signal.
ENOB = (SINADdB − 1.76)/6.02
Effective Resolution
Effective resolution is expressed in bits and is calculated as follows:
Total Harmonic Distortion (THD)
THD is the ratio of the rms sum of the first five harmonic
components to the rms value of a full-scale input signal and is
expressed in decibels.
Effective Resolution = log2(2N/RMS Input Noise)
Gain Error
Transient Response
Transient response is the time required for the ADC to accurately
acquire its input after a full-scale step function is applied.
The last transition (from 111 … 10 to 111 … 11) should occur
for an analog voltage 1½ LSB below the nominal full scale
(4.999886 V for the 0 V to 5 V range). The gain error is the
deviation of the difference between the actual level of the last
transition and the actual level of the first transition from the
difference between the ideal levels.
Zero Error
Zero error is the difference between the ideal midscale voltage,
that is, 0 V, from the actual voltage producing the midscale
output code, that is, 0 LSB.
Integral Nonlinearity Error (INL)
INL refers to the deviation of each individual code from a line
drawn from negative full scale through positive full scale. The
point used as negative full scale occurs ½ LSB before the first
code transition. Positive full scale is defined as a level 1½ LSB
beyond the last code transition. The deviation is measured from
the middle of each code to the true straight line (see Figure 22).
Rev. 0 | Page 12 of 28
AD7985
THEORY OF OPERATION
IN+
SWITCHES CONTROL
MSB
LSB
SW+
32,768C 16,384C
4C
4C
2C
2C
C
C
C
C
BUSY
REF
CONTROL
COMP
LOGIC
REFGND
OUTPUT CODE
32,768C 16,384C
MSB
LSB
SW–
CNV
IN–
Figure 21. ADC Simplified Schematic
When the conversion phase begins, SW+ and SW− are opened
first. The two capacitor arrays are then disconnected from the
analog inputs and connected to the REFGND input. Therefore,
the differential voltage between the IN+ and IN− inputs captured
at the end of the acquisition phase is applied to the comparator
inputs, causing the comparator to become unbalanced. By switch-
ing each element of the capacitor array between REFGND and
REF, the comparator input varies by binary-weighted voltage
steps (VREF/2, VREF/4, … VREF/65,536). The control logic toggles
these switches, starting with the MSB, to bring the comparator
back into a balanced condition. After the completion of this
process, the part returns to the acquisition phase, and the control
logic generates the ADC output code and a busy signal indicator.
CIRCUIT INFORMATION
The AD7985 is a fast, low power, single-supply, precise, 16-bit
ADC using a successive approximation architecture. The AD7985
features different modes to optimize performance according to the
application. In turbo mode, the AD7985 is capable of converting
2,500,000 samples per second (2.5 MSPS).
The AD7985 provides the user with an on-chip track-and-hold
and does not exhibit any pipeline delay or latency, making it
ideal for multiple multiplexed channel applications.
The AD7985 can be interfaced to any 1.8 V to 2.7 V digital logic
family. It is available in a space-saving 20-lead LFCSP that allows
flexible configurations. It is pin-for-pin compatible with the
18-bit AD7986.
Because the AD7985 has an on-board conversion clock, the
serial clock, SCK, is not required for the conversion process.
CONVERTER OPERATION
The AD7985 is a successive approximation ADC based on a
charge redistribution DAC. Figure 21 shows the simplified
schematic of the ADC. The capacitive DAC consists of two
identical arrays of 16 binary-weighted capacitors that are
connected to the two comparator inputs.
CONVERSION MODES OF OPERATION
The AD7985 features two conversion modes of operation: turbo
and normal. Turbo conversion mode (TURBO is high) allows
the fastest conversion rate of up to 2.5 MSPS and does not
power down between conversions. The first conversion in turbo
mode should be ignored because it contains meaningless data.
For applications that require lower power and slightly slower
sampling rates, the normal mode (TURBO is low) allows a
maximum conversion rate of 2.0 MSPS and powers down
between conversions. The first conversion in normal mode
contains meaningful data.
During the acquisition phase, the terminals of the array tied to
the input of the comparator are connected to AGND via SW+
and SW−. All independent switches are connected to the analog
inputs. Therefore, the capacitor arrays are used as sampling
capacitors and acquire the analog signal on the IN+ and IN−
inputs. When the acquisition phase is completed and the CNV
input goes high, a conversion phase is initiated.
Rev. 0 | Page 13 of 28
AD7985
Transfer Functions
Table 7. Output Codes and Ideal Input Voltages
Analog Input, Digital Output
REF = 4.096 V
The ideal transfer characteristic for the AD7985 is shown in
Figure 22 and Table 7.
Description
FSR – 1 LSB
Midscale + 1 LSB
Midscale
V
Code (Hex)
0xFFFF1
0x8001
4.095938 V
2.048063 V
2.048 V
111 ... 111
111 ... 110
111 ... 101
0x8000
Midscale – 1 LSB
–FSR + 1 LSB
–FSR
2.047938 V
62.5 μV
0 V
0x7FFF
0x0001
0x00002
1 This is also the code for an overranged analog input (VIN+ − VIN− above VREF
REFGND).
−
2 This is also the code for an underranged analog input (VIN+ − VIN− below REFGND).
000 ... 010
000 ... 001
000 ... 000
TYPICAL CONNECTION DIAGRAM
Figure 23 shows an example of the recommended connection
diagram for the AD7985 when multiple supplies are available.
–FSR
–FSR + 1 LSB
+FSR – 1 LSB
+FSR – 1.5 LSB
ANALOG INPUT
–FSR + 0.5 LSB
Figure 22. ADC Ideal Transfer Function
1.8V
TO
2.7V
5V
2.5V
V+
VIO
BVDD
AVDD,
DVDD
VIO
TURBO
SDI
15Ω
2.7nF
IN+
IN–
3- OR 4-WIRE
INTERFACE:
SPI, CS,
0V TO V
REF
AD7985
SCK
SDO
CNV
V–
DAISY CHAIN
(TURBO = LOW)
REF
GND
10µF
NOTES
1. GND REFERS TO REFGND, AGND, AND DGND.
Figure 23. Typical Application Diagram with Multiple Supplies
Rev. 0 | Page 14 of 28
AD7985
ANALOG INPUTS
DRIVER AMPLIFIER CHOICE
Figure 24 shows an equivalent circuit of the input structure of
the AD7985.
Although the AD7985 is easy to drive, the driver amplifier must
meet the following requirements:
The two diodes, D1 and D2, provide ESD protection for the
analog inputs, IN+ and IN−. Care must be taken to ensure that
the analog input signal does not exceed the reference input
voltage (REF) by more than 0.3 V. If the analog input signal
exceeds this level, the diodes become forward-biased and start
conducting current. These diodes can handle a forward-biased
current of 130 mA maximum. However, if the supplies of the
input buffer (for example, the V+ and V− supplies of the buffer
amplifier in Figure 23) are different from those of REF, the
analog input signal may eventually exceed the supply rails by
more than 0.3 V. In such a case (for example, an input buffer
with a short circuit), the current limitation can be used to
protect the part.
•
The noise generated by the driver amplifier must be kept as
low as possible to preserve the SNR and transition noise
performance of the AD7985. The noise from the driver is
filtered by the AD7985 analog input circuit’s one-pole, low-
pass filter, made by RIN and CIN, or by the external filter, if
one is used. Because the typical noise of the AD7985 is
50 μV rms, the SNR degradation due to the amplifier is
⎛
⎜
⎞
⎟
50
⎜
⎜
⎜
⎝
⎟
⎟
⎟
⎠
SNRLOSS = 20 log
π
2
502 + f−3dB (NeN )2
where:
REF
f
–3dB is the input bandwidth, in megahertz, of the AD7985
(20 MHz) or the cutoff frequency of the input filter, if
one is used.
N is the noise gain of the amplifier (for example, 1 in buffer
D1
D2
C
IN
R
IN
IN+ OR IN–
REFGND
C
PIN
configuration).
eN is the equivalent input noise voltage of the op amp, in
nV/√Hz.
Figure 24. Equivalent Analog Input Circuit
The analog input structure allows the sampling of the true
differential signal between IN+ and IN−. By using these
differential inputs, signals common to both inputs are rejected.
•
•
For ac applications, the driver should have a THD perfor-
mance commensurate with that of the AD7985.
For multichannel multiplexed applications, the driver
amplifier and the AD7985 analog input circuit must settle
for a full-scale step onto the capacitor array at a 16-bit level
(0.0015%, 15 ppm). In the data sheet of the driver amplifier,
settling at 0.1% to 0.01% is more commonly specified. This
value may differ significantly from the settling time at a
16-bit level and should be verified prior to driver selection.
During the acquisition phase, the impedance of the analog inputs
(IN+ and IN−) can be modeled as a parallel combination of
Capacitor CPIN and the network formed by the series connection
of RIN and CIN. CPIN is primarily the pin capacitance. RIN is typically
400 Ω and is a lumped component composed of serial resistors
and the on resistance of the switches. CIN is typically 30 pF and
is mainly the ADC sampling capacitor.
Table 8. Recommended Driver Amplifiers
Amplifier
During the sampling phase, where the switches are closed, the
input impedance is limited to CPIN. RIN and CIN make a one-pole,
low-pass filter that reduces undesirable aliasing effects and
limits noise.
Typical Application
AD8021
AD8022
ADA4899-1
AD8014
Very low noise and high frequency
Low noise and high frequency
Ultralow noise and high frequency
Low power and high frequency
When the source impedance of the driving circuit is low, the
AD7985 can be driven directly. Large source impedances
significantly affect the ac performance, especially THD. The
dc performances are less sensitive to the input impedance. The
maximum source impedance depends on the amount of THD
that can be tolerated. The THD degrades as a function of the
source impedance and the maximum input frequency.
Rev. 0 | Page 15 of 28
AD7985
Reference Decoupling
VOLTAGE REFERENCE INPUT
The AD7985 voltage reference input, REF, has a dynamic input
impedance that requires careful decoupling between the REF
and REFGND pins. The Layout section describes how this can
be done.
The AD7985 allows the choice of a very low temperature drift
internal voltage reference, an external reference, or an external
buffered reference.
The internal reference of the AD7985 provides excellent
performance and can be used in almost all applications.
When using an external reference, a very low impedance source
(for example, a reference buffer using the AD8031 or the AD8605)
and a 10 μF (X5R, 0805 size) ceramic chip capacitor are appro-
priate for optimum performance.
Internal Reference, REF = 4.096 V (PDREF Low)
To use the internal reference, the PDREF input must be low.
This enables the on-chip band gap reference and buffer, result-
ing in a 4.096 V reference on the REF pin (1.2 V on REFIN).
If an unbuffered reference voltage is used, the decoupling value
depends on the reference used. For example, a 22 μF (X5R,
1206 size) ceramic chip capacitor is appropriate for optimum
performance using a low temperature drift ADR43x reference.
The internal reference is temperature compensated to
4.096 V 15 mV. The reference is trimmed to provide
a typical drift of 10 ppm/°C.
If desired, a reference decoupling capacitor with a value as small
as 2.2 μF can be used with minimal impact on performance,
especially DNL.
The output resistance of REFIN is 6 kΩ when the internal
reference is enabled. It is necessary to decouple this pin with a
ceramic capacitor of at least 100 nF. The output resistance of
REFIN and the decoupling capacitor form an RC filter, which
helps to reduce noise.
In any case, there is no need for an additional lower value ceramic
decoupling capacitor (for example, 100 nF) between the REF
and REFGND pins.
Because the output impedance of REFIN is typically 6 kΩ,
relative humidity (among other industrial contaminants) can
directly affect the drift characteristics of the reference. A guard
ring is typically used to reduce the effects of drift under such
circumstances. However, the fine pitch of the AD7985 makes
this difficult to implement. One solution, in these industrial
and other types of applications, is to use a conformal coating,
such as Dow Corning® 1-2577 or HumiSeal® 1B73.
POWER SUPPLY
The AD7985 has four power supply pins: an analog supply
(AVDD), a buffer supply (BVDD), a digital supply (DVDD),
and a digital input/output interface supply (VIO). VIO allows
direct interface with any logic from 1.8 V to 2.7 V. To reduce the
number of supplies needed, VIO, DVDD, and AVDD can be tied
together. The power supplies do not need to be started in a par-
ticular sequence. In addition, the AD7985 is very insensitive to
power supply variations over a wide frequency range.
External 1.2 V Reference and Internal Buffer (PDREF High)
To use an external reference along with the internal buffer, PDREF
must be high. This powers down the internal reference and allows
the 1.2 V reference to be applied to REFIN, producing 4.096 V
(typically) on the REF pin.
In normal mode, the AD7985 powers down automatically at
the end of each conversion phase and, therefore, the power
scales linearly with the sampling rate. This makes the part ideal
for low sampling rates (even a few SPS) and battery-powered
applications.
External Reference (PDREF High, REFIN Low)
To apply an external reference voltage directly to the REF pin,
PDREF should be tied high and REFIN should be tied low.
BVDD should also be driven to the same potential as REF. For
example, if REF = 2.5 V, BVDD should be tied to 2.5 V.
10
1
The advantages of directly using an external voltage reference
are as follows:
•
SNR and dynamic range improvement (about 1.7 dB)
resulting from the use of a larger reference voltage (5 V)
instead of a typical 4.096 V reference when the internal
reference is used. This is calculated by
0.1
I
I
I
I
I
BVDD
AVDD
DVDD
VIO
4.096
5.0
⎛
⎜
⎝
⎞
⎟
⎠
VREF
SNR =20 log
0.01
0.1
1
SAMPLING RATE (MSPS)
•
Power savings when the internal reference is powered
down (PDREF high).
Figure 25. Operating Current vs. Sampling Rate in Normal Mode
Rev. 0 | Page 16 of 28
AD7985
DIGITAL INTERFACE
Although the AD7985 has a reduced number of pins, it offers
flexibility in its serial interface modes.
CS
mode if CNV or
SDI is low when the ADC conversion ends (see Figure 29 and
Figure 33). TURBO must be kept low for both digital interfaces.
The busy indicator feature is enabled in
CS
In
mode, the AD7985 is compatible with SPI, MICROWIRE,
CS
When CNV is low, readback can occur during conversion or
acquisition, or it can be split across acquisition and conversion,
as described in the following sections.
QSPI, and digital hosts. In
mode, the AD7985 can use either
a 3-wire or a 4-wire interface. A 3-wire interface that uses the
CNV, SCK, and SDO signals minimizes wiring connections,
which is useful, for example, in isolated applications. A 4-wire
interface that uses the SDI, CNV, SCK, and SDO signals allows
CNV, which initiates conversions, to be independent of the
readback timing (SDI). This is useful in low jitter sampling
or simultaneous sampling applications.
A discontinuous SCK is recommended because the part is selected
with CNV low, and SCK activity begins to clock out data.
Note that in the following sections, the timing diagrams indicate
digital activity (SCK, CNV, SDI, and SDO) during the conversion.
However, due to the possibility of performance degradation, digi-
tal activity should occur only prior to the safe data reading time,
tDATA, because the AD7985 provides error correction circuitry
that can correct for an incorrect bit decision during this time.
From tDATA to tCONV, there is no error correction, and conversion
results may be corrupted.
In chain mode, the AD7985 provides a daisy-chain feature that
uses the SDI input for cascading multiple ADCs on a single data
line similar to a shift register. Chain mode is available only in
normal mode (TURBO is low).
The mode in which the part operates depends on the SDI level
CS
when the CNV rising edge occurs.
mode is selected if SDI
Similarly, tQUIET, the time from the last falling edge of SCK to
the rising edge of CNV, must remain free of digital activity.
The user should configure the AD7985 and initiate the busy
is high, and chain mode is selected if SDI is low. The SDI hold
time is such that when SDI and CNV are connected together,
chain mode is always selected.
indicator (if desired in normal mode) prior to tDATA
.
In normal mode operation, the AD7985 offers the option of
forcing a start bit in front of the data bits. This start bit can be
used as a busy signal indicator to interrupt the digital host and
trigger the data reading. Otherwise, without a busy indicator,
the user must time out the maximum conversion time prior to
readback.
It is also possible to corrupt the sample by having SCK near the
sampling instant. Therefore, it is recommended that the digital
pins be kept quiet for approximately 20 ns before and 10 ns after
the rising edge of CNV, using a discontinuous SCK whenever
possible to avoid any potential performance degradation.
Rev. 0 | Page 17 of 28
AD7985
To determine how to split the read for a particular SCK frequency,
follow these examples to read data from conversion (n − 1).
DATA READING OPTIONS
There are three different data reading options for the AD7985.
There is the option to read during conversion, to split the read
across acquisition and conversion (see Figure 28 and Figure 29),
and, in normal mode, to read during acquisition. The desired
SCK frequency largely determines which reading option to use.
For turbo mode (2.5 MSPS):
f
SCK = 70 MHz; tDATA = 190 ns
Number_SCK_Edges = 70 MHz × 190 ns = 13.3
Thirteen bits are read during conversion (n), and three bits are
read during acquisition (n).
Reading During Conversion, Fast Host (Turbo or
Normal Mode)
For normal mode (2.0 MSPS):
When reading during conversion (n), conversion results are for
the previous (n − 1) conversion. Reading should occur only up
to tDATA and, because this time is limited, the host must use a
fast SCK.
fSCK = 45 MHz; tDATA = 290 ns
Number_SCK_Edges = 45 MHz × 290 ns = 13.05
Thirteen bits are read during conversion (n), and three bits are
read during acquisition (n).
The required SCK frequency is calculated by
Number _ SCK _ Edges
For slow throughputs, the time restriction is dictated by the
throughput required by the user; the host is free to run at any
speed. Similar to reading during acquisition, data access for
slow hosts must take place during the acquisition phase with
additional time into the conversion.
fSCK
≥
tDATA
To determine the minimum SCK frequency, follow these
examples to read data from conversion (n − 1).
For turbo mode (2.5 MSPS):
Note that data access spanning conversion requires the CNV
pin to be driven high to initiate a new conversion, and data
access is not allowed when CNV is high. Thus, the host must
perform two bursts of data access when using this method.
Number_SCK_Edges = 16; tDATA = 190 ns
f
SCK = 16/190 ns = 84.2 MHz
For normal mode (2.0 MSPS):
Reading During Acquisition, Any Speed Host (Turbo or
Normal Mode)
Number_SCK_Edges = 16; tDATA = 290 ns
f
SCK = 16/290 ns = 55.2 MHz
When reading during acquisition (n), conversion results are
for the previous (n − 1) conversion. Maximum throughput is
achievable in normal mode (2.0 MSPS); however, in turbo
mode, 2.5 MSPS throughput is not achievable.
The time between tDATA and tCONV is an I/O quiet time during
which digital activity should not occur, or sensitive bit decisions
may be corrupted.
Split-Reading, Any Speed Host (Turbo or Normal Mode)
For the maximum throughput, the only time restriction is that
reading take place during the tACQ (minimum) time. For slow
throughputs, the time restriction is dictated by the throughput
required by the user; the host is free to run at any speed. Thus,
for slow hosts, data access must take place during the acquisi-
tion phase.
To allow for a slower SCK, there is the option of a split read,
where data access starts at the current acquisition (n) and spans
into the conversion (n). Conversion results are for the previous
(n − 1) conversion.
Similar to reading during conversion, split-reading should
occur only up to tDATA. For the maximum throughput, the
only time restriction is that split-reading take place during the
tACQ (minimum) + (tDATA − tQUIET) time. The time between the
falling edge of SCK and CNV rising is an acquisition quiet
time, tQUIET
.
Rev. 0 | Page 18 of 28
AD7985
minimum conversion time elapses and then held high for the
maximum possible conversion time to avoid the generation of
the busy signal indicator.
CS MODE, 3-WIRE WITHOUT BUSY INDICATOR
This mode is usually used when a single AD7985 is connected
to an SPI-compatible digital host. The connection diagram is
shown in Figure 26, and the corresponding timing is given in
Figure 27.
When the conversion is complete, the AD7985 enters the
acquisition phase and powers down. When CNV goes low, the
MSB is output onto SDO. The remaining data bits are clocked
by subsequent SCK falling edges. The data is valid on both SCK
edges. Although the rising edge can be used to capture the data,
a digital host using the SCK falling edge allows a faster reading
rate, provided that it has an acceptable hold time. After the 16th
SCK falling edge or when CNV goes high (whichever occurs
first), SDO returns to high impedance.
With SDI tied to VIO, a rising edge on CNV initiates a con-
CS
version, selects
mode, and forces SDO to high impedance.
When a conversion is initiated, it continues until completion,
irrespective of the state of CNV. This can be useful, for example,
to bring CNV low to select other SPI devices, such as analog
multiplexers; however, CNV must be returned high before the
CONVERT
DIGITAL HOST
CNV
VIO
SDI
SDO
DATA IN
AD7985
SCK
CLK
CS
Figure 26. Mode, 3-Wire Without Busy Indicator Connection Diagram (SDI High)
tCYC
>tCONV
tCONV
tCONV
tDATA
tDATA
tCNVH
SDI = 1
CNV
tACQ
(I/O QUIET ACQUISITION
TIME)
(n + 1)
ACQUISITION
(n – 1)
(I/O QUIET
TIME)
(I/O QUIET
TIME)
ACQUISITION (n)
CONVERSION (n – 1)
CONVERSION (n)
tQUIET
SCK
SDO
1
14
15
16
2
14
15
16
tSCK
tHSDO
tDSDO
tEN
tEN
2
1
0
15
14
13
BEGIN DATA (n – 1)
2
1
0
tDIS
tDIS
tDIS
tDIS
END DATA (n – 2)
END DATA (n – 1)
CS
Figure 27. Mode, 3-Wire Without Busy Indicator Serial Interface Timing (SDI High)
Rev. 0 | Page 19 of 28
AD7985
When the conversion is complete, SDO goes from high imped-
ance to low impedance. With a pull-up on the SDO line, this
transition can be used as an interrupt signal to initiate the data
readback controlled by the digital host. The AD7985 then enters
the acquisition phase and powers down. The data bits are then
clocked out, MSB first, by subsequent SCK falling edges. The
data is valid on both SCK edges. Although the rising edge can
be used to capture the data, a digital host using the SCK falling
edge allows a faster reading rate, provided that it has an acceptable
hold time. After the optional 17th SCK falling edge, SDO returns
to high impedance.
CS MODE, 3-WIRE WITH BUSY INDICATOR
This mode is usually used when a single AD7985 is connected
to an SPI-compatible digital host that has an interrupt input. It
is available only in normal conversion mode (TURBO is low).
The connection diagram is shown in Figure 28, and the corre-
sponding timing is given in Figure 29.
With SDI tied to VIO, a rising edge on CNV initiates a con-
CS
version, selects
mode, and forces SDO to high impedance.
SDO is maintained in high impedance until the completion of
the conversion, irrespective of the state of CNV. Prior to the
minimum conversion time, CNV can be used to select other SPI
devices, such as analog multiplexers, but CNV must be returned
low before the minimum conversion time elapses and then held
low for the maximum possible conversion time to guarantee the
generation of the busy signal indicator.
If multiple AD7985 devices are selected at the same time, the
SDO output pin handles this contention without damage or
induced latch-up. Meanwhile, it is recommended that this
contention be kept as short as possible to limit extra power
dissipation.
CONVERT
VIO
47kΩ
DIGITAL HOST
CNV
VIO
SDI
SDO
DATA IN
IRQ
AD7985
SCK TURBO
CLK
CS
Figure 28. Mode, 3-Wire with Busy Indicator Connection Diagram (SDI High)
TURBO = 0
SDI = 1
tCYC
tCNVH
CNV
tCONV
tACQ
(I/O QUIET
TIME)
ACQUISITION
CONVERSION
ACQUISITION
tSCK
tQUIET
tSCKL
SCK
SDO
1
2
3
15
16
17
tHSDO
tSCKH
tDSDO
tDIS
D15
D14
D1
D0
CS
Figure 29. Mode, 3-Wire with Busy Indicator Serial Interface Timing (SDI High)
Rev. 0 | Page 20 of 28
AD7985
conversion time elapses and then held high for the maximum
possible conversion time to avoid the generation of the busy
signal indicator.
CS MODE, 4-WIRE WITHOUT BUSY INDICATOR
This mode is usually used when multiple AD7985 devices are
connected to an SPI-compatible digital host. A connection dia-
gram example using two AD7985 devices is shown in Figure 30,
and the corresponding timing is given in Figure 31.
When the conversion is complete, the AD7985 enters the
acquisition phase and powers down. Each ADC result can be
read by bringing its SDI input low, which consequently outputs
the MSB onto SDO. The remaining data bits are then clocked by
subsequent SCK falling edges. The data is valid on both SCK
edges. Although the rising edge can be used to capture the data,
a digital host using the SCK falling edge allows a faster reading
rate, provided that it has an acceptable hold time. After the 16th
SCK falling edge, SDO returns to high impedance and another
AD7985 can be read.
With SDI high, a rising edge on CNV initiates a conversion,
CS
selects
mode, and forces SDO to high impedance. In this
mode, CNV must be held high during the conversion phase
and the subsequent data readback. (If SDI and CNV are low,
SDO is driven low.) Prior to the minimum conversion time,
SDI can be used to select other SPI devices, such as analog multi-
plexers, but SDI must be returned high before the minimum
CS2
CS1
CONVERT
CNV
CNV
DIGITAL HOST
SDI
SDO
AD7985
SDI
SDO
AD7985
SCK
SCK
DATA IN
CLK
CS
Figure 30. Mode, 4-Wire Without Busy Indicator Connection Diagram
tCYC
tCONV
tCONV
tDATA
tDATA
CNV
tACQ
ACQUISITION
(n – 1)
(I/O QUIET
TIME)
ACQUISITION
(n + 1)
(I/O QUIET
TIME)
(I/O QUIET
TIME)
ACQUISITION (n)
CONVERSION (n – 1)
tHSDICNV
CONVERSION (n)
SDI
tSSDICNV
tQUIET
SCK
SDO
1
14
15
16
2
14
2
15
1
16
tSCK
tHSDO
tDSDO
tEN
tEN
2
1
0
15
14
13
BEGIN DATA (n – 1)
0
tHSDO
tDIS
tDIS
END DATA (n – 2)
END DATA (n – 1)
CS
Figure 31. Mode, 4-Wire Without Busy Indicator Serial Interface Timing
Rev. 0 | Page 21 of 28
AD7985
used to select other SPI devices, such as analog multiplexers, but
SDI must be returned low before the minimum conversion time
elapses and then held low for the maximum possible conversion
time to guarantee the generation of the busy signal indicator.
CS MODE, 4-WIRE WITH BUSY INDICATOR
This mode is usually used when a single AD7985 is connected
to an SPI-compatible digital host with an interrupt input and
when it is desired to keep CNV, which is used to sample the
analog input, independent of the signal used to select the data
reading. This independence is particularly important in applica-
tions where low jitter on CNV is desired. This mode is available
only in normal conversion mode (TURBO is low). The connection
diagram is shown in Figure 32, and the corresponding timing is
given in Figure 33.
When the conversion is complete, SDO goes from high imped-
ance to low impedance. With a pull-up on the SDO line, this
transition can be used as an interrupt signal to initiate the data
readback controlled by the digital host. The AD7985 then enters
the acquisition phase and powers down. The data bits are then
clocked out, MSB first, by subsequent SCK falling edges. The
data is valid on both SCK edges. Although the rising edge can
be used to capture the data, a digital host using the SCK falling
edge allows a faster reading rate, provided that it has an accept-
able hold time. After the optional 17th SCK falling edge or when
SDI goes high (whichever occurs first), SDO returns to high
impedance.
With SDI high, a rising edge on CNV initiates a conversion,
CS
selects
mode, and forces SDO to high impedance. In this
mode, CNV must be held high during the conversion phase and
the subsequent data readback. (If SDI and CNV are low, SDO is
driven low.) Prior to the minimum conversion time, SDI can be
CS1
CONVERT
VIO
47kΩ
DIGITAL HOST
CNV
SDI
SDO
DATA IN
IRQ
AD7985
TURBO
SCK
CLK
CS
Figure 32. Mode, 4-Wire with Busy Indicator Connection Diagram
TURBO = 0
CNV
tCYC
tACQ
tCONV
(I/O QUIET
TIME)
ACQUISITION
CONVERSION
ACQUISITION
tSSDICNV
SDI
tSCK
tHSDICNV
tSCKL
tQUIET
SCK
SDO
1
2
3
15
tSCKH
16
17
tHSDO
tDSDO
tDIS
tEN
D15
D14
D1
D0
CS
Figure 33. Mode, 4-Wire with Busy Indicator Serial Interface Timing
Rev. 0 | Page 22 of 28
AD7985
When the conversion is complete, the MSB is output onto SDO,
and the AD7985 enters the acquisition phase and powers down.
The remaining data bits stored in the internal shift register are
clocked by subsequent SCK falling edges. For each ADC, SDI
feeds the input of the internal shift register and is clocked by the
SCK falling edge. Each ADC in the chain outputs its data MSB
first, and 16 × N clocks are required to read back the N ADCs.
The data is valid on both SCK edges. Although the rising edge
can be used to capture the data, a digital host using the SCK
falling edge allows a faster reading rate and consequently more
AD7985 devices in the chain, provided that the digital host has
an acceptable hold time. The maximum conversion rate may be
reduced due to the total readback time.
CHAIN MODE WITHOUT BUSY INDICATOR
This mode can be used to daisy-chain multiple AD7985 devices on
a 3-wire serial interface. It is available only in normal conversion
mode (TURBO is low). This feature is useful for reducing com-
ponent count and wiring connections, for example, in isolated
multiconverter applications or for systems with a limited inter-
facing capacity. Data readback is analogous to clocking a shift
register. A connection diagram example using two AD7985
devices is shown in Figure 34, and the corresponding timing is
given in Figure 35.
When SDI and CNV are low, SDO is driven low. With SCK low,
a rising edge on CNV initiates a conversion, selects chain mode,
and disables the busy indicator. In this mode, CNV is held high
during the conversion phase and the subsequent data readback.
CONVERT
CNV
CNV
DIGITAL HOST
DATA IN
SDI
SDO
AD7985
SDI
SDO
AD7985
A
B
TURBO
TURBO
SCK
SCK
CLK
Figure 34. Chain Mode Without Busy Indicator Connection Diagram
TURBO = 0
SDI = 0
A
tCYC
CNV
tACQ
tCONV
ACQUISITION
CONVERSION
ACQUISITION
tSCK
tSCKL
tQUIET
SCK
1
A
B
2
3
A
B
14
15
16
17
18
30
31
32
tHSCKCNV
tSSDISCK
tSCKH
tHSDISCK
tEN
D
D
15
D
14
D
D
13
13
D
1
1
D
0
SDO = SDI
A
A
A
A
B
tHSDO
tDSDO
15
D
14
D
B
D
0
D
15
D
14
D
1
D 0
A
SDO
B
B
A
A
A
B
Figure 35. Chain Mode Without Busy Indicator Serial Interface Timing
Rev. 0 | Page 23 of 28
AD7985
When all ADCs in the chain have completed their conversions, the
SDO pin of the ADC closest to the digital host (see the AD7985
ADC labeled C in Figure 36) is driven high. This transition on
SDO can be used as a busy indicator to trigger the data read-
back controlled by the digital host. The AD7985 then enters the
acquisition phase and powers down. The data bits stored in the
internal shift register are clocked out, MSB first, by subsequent SCK
falling edges. For each ADC, SDI feeds the input of the internal
shift register and is clocked by the SCK falling edge. Each ADC
in the chain outputs its data MSB first, and 16 × N + 1 clocks
are required to read back the N ADCs. Although the rising edge
can be used to capture the data, a digital host using the SCK
falling edge allows a faster reading rate and consequently more
AD7985 devices in the chain, provided that the digital host has
an acceptable hold time.
CHAIN MODE WITH BUSY INDICATOR
This mode can be used to daisy-chain multiple AD7985 devices
on a 3-wire serial interface while providing a busy indicator. It
is available only in normal conversion mode (TURBO is low).
This feature is useful for reducing component count and wiring
connections, for example, in isolated multiconverter applications
or for systems with a limited interfacing capacity. Data readback
is analogous to clocking a shift register. A connection diagram
example using three AD7985 devices is shown in Figure 36, and
the corresponding timing is given in Figure 37.
When SDI and CNV are low, SDO is driven low. With SCK high,
a rising edge on CNV initiates a conversion, selects chain mode,
and enables the busy indicator feature. In this mode, CNV is
held high during the conversion phase and the subsequent data
readback.
CONVERT
CNV
CNV
CNV
DIGITAL HOST
SDI
SDO
AD7985
SDI
SDO
SDI
SDO
AD7985
AD7985
DATA IN
IRQ
A
B
C
SCK
SCK
SCK
TURBO
TURBO
TURBO
CLK
Figure 36. Chain Mode with Busy Indicator Connection Diagram
TURBO = 0
tCYC
CNV = SDI
A
tCONV
tACQ
ACQUISITION
CONVERSION
ACQUISITION
tSCK
tSSCKCNV
tSCKH
SCK
1
2
3
4
15
16
17
18
19
31
32
33
34
35
47
48
49
tHSCKCNV
tSSDISCK
tSCKL
tDSDOSDI
tHSDISCK
tEN
SDO = SDI
D
15
D
14
D
13
A
D
1
D 0
A
A
B
A
A
A
tHSDO
tDSDO
tDSDOSDI
tDSDOSDI
tDSDOSDI
SDO = SDI
B
D
15
D
D
14
D
13
B
D
D
1
D
0
D
15
D
14
D 1
A
D 0
A
C
B
B
B
B
A
A
tDSDOSDI
SDO
D
15
14
D
13
1
D
0
D
15
D
14
D
1
D
0
D
15
D
14
D
1
D 0
A
C
C
C
C
C
C
B
B
B
B
A
A
A
Figure 37. Chain Mode with Busy Indicator Serial Interface Timing
Rev. 0 | Page 24 of 28
AD7985
APPLICATIONS INFORMATION
Finally, the power supplies, VDD and VIO of the AD7985,
LAYOUT
should be decoupled with ceramic capacitors, typically 100 nF,
placed close to the AD7985 and connected using short, wide
traces to provide low impedance paths and to reduce the effect
of glitches on the power supply lines.
The printed circuit board (PCB) that houses the AD7985
should be designed so that the analog and digital sections
are separated and confined to certain areas of the board.
The pinout of the AD7985, with its analog signals on the left
side and its digital signals on the right side, eases this task.
EVALUATING AD7985 PERFORMANCE
Avoid running digital lines under the device because they
couple noise onto the die, unless a ground plane under the
AD7985 is used as a shield. Fast switching signals, such as
CNV or clocks, should not run near analog signal paths.
Crossover of digital and analog signals should be avoided.
Other recommended layouts for the AD7985 are outlined
in the documentation for the AD7985 evaluation board
(EVAL-AD7985EBZ). The evaluation board package includes
a fully assembled and tested evaluation board, documentation,
and software for controlling the board from a PC via the
EVAL-CED1Z board.
At least one ground plane should be used. It can be common or
split between the digital and analog sections. In the latter case,
the planes should be joined underneath the AD7985 devices.
The AD7985 voltage reference inputs (REF) have a dynamic
input impedance and should be decoupled with minimal
parasitic inductances. This is done by placing the reference
decoupling ceramic capacitor close to, ideally right up against,
the REF and REFGND pins and connecting them with wide,
low impedance traces.
Rev. 0 | Page 25 of 28
AD7985
BVDD
AVDD
REF
REF
REF
PADDLE
1
2
GND
GND
GND
GND
3
4
DVDD
5
6
GND
GND
GND
VIO
Figure 38. Example Layout of the AD7985 (Top Layer)
5V
EXTERNAL
REFERENCE
(ADR435 OR ADR445)
BVDD
AVDD
C
AVDD
C
BVDD
REF
REF
REF
GND
C
REF
GND
GND
GND
C
DVDD
GND
DVDD
GND GND GND
VIO
VIO
C
VIO
Figure 39. Example Layout of the AD7985 (Bottom Layer)
Rev. 0 | Page 26 of 28
AD7985
OUTLINE DIMENSIONS
0.60 MAX
4.00
BSC SQ
0.60 MAX
PIN 1
INDICATOR
15
16
20
1
5
0.50
BSC
2.65
2.50 SQ
2.35
PIN 1
INDICATOR
3.75
BSC SQ
EXPOSED
PAD
(BOTTOM VIEW)
10
11
6
0.50
0.40
0.30
0.25 MIN
TOP VIEW
0.80 MAX
0.65 TYP
12° MAX
1.00
0.85
0.80
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.20 REF
SECTION OF THIS DATA SHEET.
0.30
0.23
0.18
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-220-VGGD-1
Figure 40. 20-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
4 mm × 4 mm Body, Very Thin Quad
(CP-20-4)
Dimensions shown in millimeters
ORDERING GUIDE
Package
Option
Ordering
Quantity
Model
Temperature Range
−40°C to +85°C
−40°C to +85°C
Package Description
AD7985BCPZ1
AD7985BCPZ-RL71
EVAL-AD7985EBZ1, 2
EVAL-CED1Z3
20-Lead Lead Frame Chip Scale Package [LFCSP_VQ], Tray
20-Lead Lead Frame Chip Scale Package [LFCSP_VQ], Reel
Evaluation Board
CP-20-4
CP-20-4
490
1,500
Converter Evaluation and Development Board
1 Z = RoHS Compliant Part.
2 This board can be used as a standalone evaluation board or in conjunction with the EVAL-CED1Z for evaluation/demonstration purposes.
3 This board allows a PC to control and communicate with all Analog Devices evaluation boards ending in the EB designator.
Rev. 0 | Page 27 of 28
AD7985
NOTES
©2009 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D07947-0-9/09(0)
Rev. 0 | Page 28 of 28
相关型号：
©2020 ICPDF网 联系我们和版权申明