AD8118_技术文档

600 MHz, 32 × 32 Buffered

Analog Crosspoint Switch

AD8117/AD8118

FEATURES

FUNCTIONAL BLOCK DIAGRAM

D0 D1 D2 D3 D4 D5

VDD

DGND

High channel count, 32 × 32 high speed, non-blocking

switch array

Differential or single-ended operation

Differential G = +1 (AD8117) or G = +2 (AD8118)

Flexible power supplies

Single +5 V supply, or dual 2.5 V supplies

Serial or parallel programming of switch array

High impedance output disable allows connection of

multiple devices with minimal loading on output bus

Excellent video performance

>50 MHz 0.1 dB gain flatness

0.05%/0.05° differential gain/phase error (R_L= 150 Ω)

Excellent ac performance

Bandwidth: 600 MHz

Slew rate: 1800 V/μs

A0

A1

A2

A3

A4

AD8117/

AD8118

SER/PAR

WE

1

0

192-BIT SHIFT REGISTER

WITH 6-BIT

PARALLEL LOADING

DATA

OUT

CLK

DATA IN

192

UPDATE

RESET

PARALLEL LATCH

192

DECODE

32 × 6:32 DECODERS

32

INPUT

1024

OUTPUT

BUFFER

G = +1

RECEIVER

G = +1*

G = +2**

2

Settling time: 2.5 ns to 1%

Low power of 2.5 W

Low all hostile crosstalk

< −70 dB @ 5 MHz

SWITCH

MATRIX

< −43 dB @ 600 MHz

Reset pin allows disabling of all outputs (connected through

a capacitor to ground provides power-on reset capability)

304-ball BGA package (31 mm × 31 mm)

APPLICATIONS

Routing of high speed signals including

RGB and component video routing

KVM

*AD8117 ONLY

**AD8118 ONLY

VPOS VNEG

VOCM

Figure 1.

Compressed video (MPEG, wavelet)

Data communications

GENERAL DESCRIPTION

The AD8117/AD8118 are high speed, 32 × 32 analog crosspoint

switch matrices. They offer 600 MHz bandwidth and slew rate of

1800 V/μs for high resolution computer graphics (RGB) signal

switching. With less than −70 dB of crosstalk and −90 dB

isolation (@ 5 MHz), the AD8117/AD8118 are useful in many

high speed applications. The 0.1 dB flatness greater than

50 MHz makes the AD8117/AD8118 ideal for composite video

switching.

back-terminated load applications. They operate as fully

differential devices or can be configured for single-ended

operation. Either a single +5 V supply or dual 2.5 V supplies

can be used, while consuming only 500 mA of idle current with

all outputs enabled. The channel switching is performed via a

double-buffered, serial digital control (which can accommodate

daisy chaining of several devices), or via a parallel control,

allowing updating of an individual output without reprogram-

ming the entire array.

The AD8117/AD8118 include 32 independent output buffers

that can be placed into a high impedance state for paralleling

crosspoint outputs so that off-channels present minimal loading

to an output bus. The AD8117 has a differential gain of +1,

while the AD8118 has a differential gain of +2 for ease of use in

The AD8117/AD8118 are packaged in a 304-ball BGA package

and are available over the extended industrial temperature

range of −40°C to +85°C.

Rev. A

Information furnished by Analog Devices is believed to be accurate and reliable. However, no

responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other

rights of third parties that may result from its use. Specifications subject to change without notice. No

license is granted by implication or otherwise under any patent or patent rights of Analog Devices.

Trademarks and registeredtrademarks arethe property of their respective owners.

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.

Tel: 781.329.4700

Fax: 781.461.3113

www.analog.com

AD8117/AD8118

TABLE OF CONTENTS

Features .............................................................................................. 1

ESD Caution...................................................................................7

Pin Configuration and Function Descriptions..............................8

Truth Table and Logic Diagram ............................................... 13

I/O Schematics................................................................................ 15

Typical Performance Characteristics ........................................... 17

Theory of Operation ...................................................................... 25

Applications..................................................................................... 26

Programming.............................................................................. 26

Operating Modes........................................................................ 27

Outline Dimensions....................................................................... 36

Ordering Guide .......................................................................... 36

Applications....................................................................................... 1

Functional Block Diagram .............................................................. 1

General Description......................................................................... 1

Revision History ............................................................................... 2

Specifications..................................................................................... 3

Timing Characteristics (Serial Mode) ....................................... 5

Timing Characteristics (Parallel Mode) .................................... 6

Absolute Maximum Ratings............................................................ 7

Thermal Resistance ...................................................................... 7

Power Dissipation......................................................................... 7

REVISION HISTORY

5/07—Rev. 0 to Rev. A

Added AD8118 ...................................................................Universal

Changes to Data Sheet Title ........................................................... 1

Changes to Table 1............................................................................ 3

2/07—Revision 0: Initial Version

Rev. A | Page 2 of 36

AD8117/AD8118

SPECIFICATIONS

V_S= 2.5 V at T_A= 25°C, R_{L, diff}= 200 Ω, V_OCM= 0 V, differential I/O mode, unless otherwise noted.

Table 1.

AD8117/AD8118

Parameter

Conditions

Min

Typ

Max

Unit

DYNAMIC PERFORMANCE

−3 dB Bandwidth

200 mV p-p, typical channel

2 V p-p, typical channel

0.1 dB, 200 mV p-p

0.1 dB, 2 V p-p

2 V p-p

1%, 2 V step

600

MHz

ns

V/μs

420/525

100/50

70/50

1.3

2.5

1800

1500

Gain Flatness

Propagation Delay

Settling Time

Slew Rate

2 V step, peak

2 V step, 10% to 90%

NOISE/DISTORTION PERFORMANCE

Differential Gain Error

Differential Phase Error

Crosstalk, All Hostile

NTSC or PAL, R_L= 150 Ω

f = 5 MHz

f = 10 MHz

f = 100 MHz

f = 600 MHz

f = 10 MHz, one channel

0.1 MHz to 50 MHz

0.05

%

Degrees

dB

−70/−75

−65/−70

−45/−50

−43/−50

−90

Off Isolation, Input-Output

Input Voltage Noise

DC PERFORMANCE

Voltage Gain

dB

nV/√Hz

45/53

Differential

+1/+2

1

V/V

%

Gain Error

No load

1

3

%

Gain Matching

Channel-to-channel

1

%

Differential Offset

5

25

90

mV

Common-Mode Offset

OUTPUT CHARACTERISTICS

Output Impedance

DC, enabled

Disabled, differential

Disabled

No load

V_{OUT, diff}= 2 V p-p

V_{OUT, diff}= 2.8 V p-p

Single-ended output

Maximum operating signal

0.1

30

4

Ω

kΩ

pF

μA

V p-p

V

mA

Output Disable Capacitance

Output Leakage Current

Output Voltage Range

V_OCMInput Range

1

2.8

3.8

−0.5

−0.25

−1.3

0.8

0.6

1.3

Output Swing Limit

Output Current

30

INPUT CHARACTERISTICS

Input Voltage Range

Common mode, V_{IN, diff}= 2 V p-p

Differential

f = 10 MHz

Any switch configuration

Differential

−2

2

V

2/1

48

2

5

1

Common-Mode Rejection Ratio

Input Capacitance

Input Resistance

Input Offset Current

V_OCMInput Bias Current

V_OCMInput Impedance

dB

pF

kΩ

ꢀA

μA

kΩ

64

4

Rev. A | Page 3 of 36

AD8117/AD8118

Parameter

Conditions

Min

Typ

Max

Unit

SWITCHING CHARACTERISTICS

Enable On Time

Switching Time, 2 V Step

Switching Transient (Glitch)

POWER SUPPLIES

50% update to 1% settling

Differential

100

40

ns

mV p-p

Supply Current

V_POS, outputs enabled, no load

Outputs disabled

V_NEG, outputs enabled, no load

Outputs disabled

500

200

500

200

580

240

580

240

1.2

mA

V

V_DD, outputs enabled, no load

Supply Voltage Range

PSRR

4.5 to 5.5

85

75

V_NEG, V_POS, f = 1 MHz

V_OCM, f = 1 MHz

dB

OPERATING TEMPERATURE RANGE

Temperature Range

θ_JA

θ_JC

Operating (still air)

−40 to +85

14

1

°C

°C/W

Rev. A | Page 4 of 36

AD8117/AD8118

TIMING CHARACTERISTICS (SERIAL MODE)

Specifications subject to change without notice.

Table 2.

Limit

Typ

Parameter

Symbol

Min

40

50

Max

Unit

ns

Serial Data Setup Time

CLK Pulse Width

t₁

t₂

t₃

t₄

t₅

t₆

t₇

Serial Data Hold Time

CLK Pulse Separation

CLK to UPDATE Delay

UPDATE Pulse Width

CLK to DATA OUT Valid

Propagation Delay, UPDATE to Switch On or Off

RESET Pulse Width

50

150

10

90

120

100

200

60

RESET Time

1

WE

0

t₂

t₄

1

CLK

0

LOAD DATA INTO

SERIAL REGISTER

ON FALLING EDGE

t₁

t₃

1

DATA IN

0

OUT31 (D5)

OUT30 (D4)

OUT00 (D0)

t₅

t₆

1 = LATCHED

TRANSFER DATA FROM SERIAL

REGISTER TO PARALLEL

LATCHES DURING LOW LEVEL

UPDATE

0 = TRANSPARENT

t₇

DATA OUT

Figure 2. Timing Diagram, Serial Mode

Table 3. Logic Levels

V_IH

V_IL

V_OH

V_OL

I_IH

RESET¹,

I_IL

RESET¹,

I_OH

I_OL

RESET,

DATA OUT

SER/PAR, CLK,

DATA IN,

UPDATE

SER/PAR, CLK,

DATA IN,

UPDATE

SER/PAR, CLK,

DATA IN,

UPDATE

SER/PAR, CLK,

DATA IN,

UPDATE

2.0 V min

0.6 V max

V_DD− 0.3 V min D_GND+ 0.5 V max

1 ꢀA max

–1 ꢀA min

−1 mA max

1 mA min

¹See Figure 15.

Rev. A | Page 5 of 36

AD8117/AD8118

TIMING CHARACTERISTICS (PARALLEL MODE)

Specifications subject to change without notice.

Table 4.

Limit

Typ

Parameter

Symbol

Min

80

110

150

90

Max

Unit

ns

Parallel Data Setup Time

WE Pulse Width

t₁

t₂

t₃

t₄

t₅

t₆

Parallel Data Hold Time

WE Pulse Separation

WE to UPDATE Delay

UPDATE Pulse Width

Propagation Delay, UPDATE to Switch On or Off

RESET Pulse Width

ns

10

ns

90

ns

100

200

ns

60

ns

RESET Time

ns

t₂

t₄

1

WE

0

t₁

t₃

1

D0 TO D5

A0 TO A4

0

t₅

t₆

1 = LATCHED

UPDATE

0 = TRANSPARENT

Figure 3. Timing Diagram, Parallel Mode

Table 5. Logic Levels

V_IH

V_IL

V_OH

V_OL

I_IH

RESET¹,

I_IL

RESET¹,

I_OH

I_OL

RESET,

DATA OUT

SER/PAR, WE,

D0, D1, D2, D3, D0, D1, D2, D3,

D4, D5, A0, A1, D4, D5, A0, A1,

D0, D1, D2, D3, D0, D1, D2, D3,

D4, D5, A0, A1, D4, D5, A0, A1,

A2, A3, A4,

UPDATE

A2, A3, A4,

UPDATE

A2, A3, A4,

UPDATE

A2, A3, A4,

UPDATE

2.0 V min

0.6 V max

Disabled

1 μA max

–1 μA min

Disabled

¹See Figure 15.

Rev. A | Page 6 of 36

AD8117/AD8118

ABSOLUTE MAXIMUM RATINGS

Table 6.

POWER DISSIPATION

Parameter

Rating

The AD8117/AD8118 are operated with 2.5 V or +5 V

supplies and can drive loads down to 100 ꢀ, resulting in a large

range of possible power dissipations. For this reason, extra care

must be taken derating the operating conditions based on

ambient temperature.

Analog Supply Voltage (V_POS– V_NEG

Digital Supply Voltage (V_DD– D_GND

Ground Potential Difference

)

6 V

+0.5 V to −2.5 V

(V_NEG– D_GND

Maximum Potential Difference

(V_DD– V_NEG

Common-Mode Analog Input

Voltage

Differential Analog Input Voltage

Digital Input Voltage

Output Voltage

)

8 V

Packaged in a 304-ball BGA, the AD8117/AD8118 junction-to-

ambient thermal impedance (θ_JA) is 14°C/W. For long-term

reliability, the maximum allowed junction temperature of the

die should not exceed 150°C. Temporarily exceeding this limit

may cause a shift in parametric performance due to a change in

stresses exerted on the die by the package. Exceeding a junction

temperature of 175°C for an extended period can result in

device failure. The following curve shows the range of allowed

internal die power dissipations that meet these conditions over

the −40°C to +85°C ambient temperature range. When using

the table, do not include external load power in the maximum

power calculation, but do include load current dropped on the

die output transistors.

)

V_NEGto V_POS

2 V

V_DD

(V_POS− 1 V) to (V_NEG+ 1 V)

(Disabled Analog Output)

Output Short-Circuit Duration

Output Short-Circuit Current

Storage Temperature

Operating Temperature Range

Lead Temperature

(Soldering 10 sec)

Momentary

80 mA

−65°C to +125°C

−40°C to +85°C

300°C

Junction Temperature

150°C

8

T

= 150°C

J

Stresses above those listed under Absolute Maximum Ratings

may cause permanent damage to the device. This is a stress

rating only; functional operation of the device at these or any

other conditions above those indicated in the operational

section of this specification is not implied. Exposure to absolute

maximum rating conditions for extended periods may affect

device reliability.

7

6

5

4

THERMAL RESISTANCE

15

25

35

45

55

65

75

85

θ_JAis specified for the worst-case conditions, that is, a device

soldered in a circuit board for surface-mount packages.

AMBIENT TEMPERATURE (°C)

Figure 4. Maximum Die Power Dissipation vs. Ambient Temperature

Table 7. Thermal Resistance

Package Type

θ_JA

θ_JC

θ_JB

ψ_JT

ψ_JB

Unit

ESD CAUTION

304-Ball BGA

14

1

6.5

0.6

5.7

°C/W

Rev. A | Page 7 of 36

AD8117/AD8118

PIN CONFIGURATION AND FUNCTION DESCRIPTIONS

23

22

21

20

19

18

17

16

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

VPOS OP17

OP16 ON16

ON17

OP19

ON19

OP21

ON21

OP23

ON23

OP25

ON25

OP27

ON27

OP29

ON29

OP31

ON31 VPOS

VPOS VPOS

VPOS VPOS VPOS

A

B

A

B

OP18

ON18

OP20

ON20

OP22

ON22

OP24

ON24

OP26

ON26

OP28

ON28

OP30

ON30

VPOS VNEG VNEG VNEG VNEG VNEG VNEG VPOS VPOS VPOS VNEG VNEG VNEG VNEG VNEG VNEG VPOS VPOS

VNEG VOCM VNEG VNEG VNEG VNEG VNEG VPOS VPOS VPOS VNEG VNEG VNEG VNEG VNEG VOCM VNEG VPOS

C

VPOS VPOS

IN17

IP0

IN0

VPOS

IP1

IN16

IP16

IN18

IP18

IN20

IP20

IN22

IP22

IN24

IP24

IN26

IP26

IN28

IP28

IN30

IP30

VPOS

D

VNEG VOCM

VOCM VNEG

E

VNEG

VDD

VNEG

IP2

IN1

IP17

IN19

IP19

IN21

IP21

IN23

IP23

IN25

IP25

IN27

IP27

IN29

IP29

IN31

IP31

F

VNEG DGND

VNEG RESET

VNEG

DGND VNEG

IN2

IP3

G

H

G

H

DATA

VNEG

OUT

IP4

IN3

CLK

VNEG

VPOS

VNEG

IN4

IP5

J

DATA

IN

VNEG

VPOS

VNEG

WE

D5

IP6

IN5

K

SER/

PAR

IN6

IP7

L

AD8117/AD8118

A4

A3

IP8

IN7

D4

M

N

M

N

BOTTOM VIEW

(Not to Scale)

IN8

IP9

D3

A2

IP10

IN10

IP12

IN12

IP14

IN14

VPOS

IN9

D2

P

A1

IP11

IN11

IP13

IN13

IP15

IN15

D1

R

D0

A0

T

VDD

U

VNEG DGND

VNEG VOCM

DGND VNEG

VOCM VNEG

V

W

Y

W

Y

VPOS

VNEG VOCM VNEG VNEG VNEG VNEG VNEG VPOS VPOS VPOS VNEG VNEG VNEG VNEG VNEG VOCM VNEG VPOS

VPOS VNEG VNEG VNEG VNEG VNEG VNEG VPOS VPOS VPOS VNEG VNEG VNEG VNEG VNEG VNEG VPOS VPOS

VPOS VPOS

VPOS VPOS VPOS

AA

AB

AC

AA

AB

AC

VPOS ON14

ON15 OP15

OP14

ON13

ON12

OP13

OP12

ON11

ON10

OP11

OP10

ON9

ON8

OP9

OP8

ON7

ON6

OP7

OP6

ON5

ON4

OP5

OP4

ON3

ON2

OP3

OP2

ON1

ON0

OP1

OP0

VPOS

VPOS VPOS

23

22

21

20

19

18

17

16

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

Figure 5. Package Bottom View

Rev. A | Page 8 of 36

AD8117/AD8118

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

23

22

21

VPOS VPOS

VPOS ON31

VPOS VPOS

OP31

OP21

VPOS VPOS VPOS

ON29

OP29

ON27

OP27

ON25

OP25

ON23

OP23

ON21

ON19

OP19

ON17

OP17 VPOS

ON16 OP16

A

B

A

ON30

OP30

ON28

OP28

ON26

OP26

ON24

OP24

ON22

OP22

ON20

OP20

ON18

OP18

B

VPOS VPOS VNEG VNEG VNEG VNEG VNEG VNEG VPOS VPOS VPOS VNEG VNEG VNEG VNEG VNEG VNEG VPOS

VPOS VNEG VOCM VNEG VNEG VNEG VNEG VNEG VPOS VPOS VPOS VNEG VNEG VNEG VNEG VNEG VOCM VNEG

C

VPOS

IP1

IP0

IN0

VPOS VPOS

VOCM VNEG

IN17

IN16

IP16

IN18

IP18

IN20

IP20

IN22

IP22

IN24

IP24

IN26

IP26

IN28

IP28

IN30

IP30

VPOS

D

VNEG VOCM

E

IN1

IP2

VNEG

VDD

VNEG

IP17

IN19

IP19

IN21

IP21

IN23

IP23

IN25

IP25

IN27

IP27

IN29

IP29

IN31

IP31

F

IP3

IN2

VNEG DGND

DGND VNEG

RESET VNEG

VNEG

G

H

G

H

DATA

VNEG

IN3

IP4

OUT

IP5

IN4

VNEG

VPOS

VNEG

CLK

J

DATA

IN

IN5

IP6

VNEG

VPOS

VNEG

WE

D5

K

SER/

PAR

IP7

IN6

L

AD8117/AD8118

IN7

IP8

A4

A3

D4

M

N

M

N

TOP VIEW

(Not to Scale)

IP9

IN8

D3

IN9

IP10

IN10

IP12

IN12

IP14

IN14

VPOS

A2

D2

P

IP11

IN11

IP13

IN13

IP15

IN15

A1

D1

R

A0

D0

T

VDD

U

VNEG DGND

VNEG VOCM

DGND VNEG

VOCM VNEG

V

W

Y

W

Y

VPOS VNEG VOCM VNEG VNEG VNEG VNEG VNEG VPOS VPOS VPOS VNEG VNEG VNEG VNEG VNEG VOCM VNEG

VPOS VPOS VNEG VNEG VNEG VNEG VNEG VNEG VPOS VPOS VPOS VNEG VNEG VNEG VNEG VNEG VNEG VPOS

VPOS

VPOS VPOS

VPOS VPOS VPOS

AA

AB

AC

AA

AB

AC

VPOS

OP0

ON0

OP1

ON10

OP11

OP12

ON11

ON12

OP13

OP14

ON13

ON14 VPOS

OP15 ON15

OP2

ON1

ON2

OP3

OP4

ON3

ON4

OP5

OP6

ON5

ON6

OP7

OP8

ON7

ON8

OP9

OP10

ON9

VPOS VPOS

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

Figure 6. Package Top View

Table 8. Ball Grid Description

Ball No. Mnemonic Description

A1

A2

A3

A4

A5

A6

A7

A8

VPOS

ON31

OP31

ON29

OP29

ON27

OP27

ON25

OP25

ON23

OP23

ON21

Analog Positive Power Supply.

A15

A16

A17

A18

A19

A20

A21

A22

A23

B1

OP21

ON19

OP19

ON17

OP17

VPOS

ON30

Output Number 21, Positive Phase.

Output Number 19, Negative Phase.

Output Number 19, Positive Phase.

Output Number 17, Negative Phase.

Output Number 17, Positive Phase.

Analog Positive Power Supply.

Output Number 30, Negative Phase.

Output Number 31, Negative Phase.

Output Number 31, Positive Phase.

Output Number 29, Negative Phase.

Output Number 29, Positive Phase.

Output Number 27, Negative Phase.

Output Number 27, Positive Phase.

Output Number 25, Negative Phase.

Output Number 25, Positive Phase.

Output Number 23, Negative Phase.

Output Number 23, Positive Phase.

Output Number 21, Negative Phase.

A9

A10

A11

A12

A13

A14

B2

B3

B4

B5

Rev. A | Page 9 of 36

AD8117/AD8118

Ball No. Mnemonic Description

B6

B7

B8

B9

OP30

ON28

OP28

ON26

OP26

ON24

OP24

ON22

OP22

ON20

OP20

ON18

OP18

ON16

OP16

VPOS

VNEG

VPOS

VNEG

VPOS

IP0

Output Number 30, Positive Phase.

Output Number 28, Negative Phase.

Output Number 28, Positive Phase.

Output Number 26, Negative Phase.

Output Number 26, Positive Phase.

Output Number 24, Negative Phase.

Output Number 24, Positive Phase.

Output Number 22, Negative Phase.

Output Number 22, Positive Phase.

Output Number 20, Negative Phase.

Output Number 20, Positive Phase.

Output Number 18, Negative Phase.

Output Number 18, Positive Phase.

Output Number 16, Negative Phase.

Output Number 16, Positive Phase.

Analog Positive Power Supply.

Analog Negative Power Supply.

Analog Positive Power Supply.

Analog Negative Power Supply.

Analog Positive Power Supply.

Input Number 0, Positive Phase.

Analog Positive Power Supply.

Analog Negative Power Supply.

D12

D13

D14

D15

D16

D17

D18

D19

VPOS

VNEG

VOCM

Analog Positive Power Supply.

Analog Negative Power Supply.

Output Common-Mode Reference

Supply.

Analog Negative Power Supply.

Analog Positive Power Supply.

B10

B11

B12

B13

B14

B15

B16

B17

B18

B19

B20

B21

B22

B23

C1

C2

C3

C4

C5

C6

C7

C8

C9

C10

C11

C12

C13

C14

C15

C16

C17

C18

C19

C20

C21

C22

C23

D1

D20

D21

D22

VNEG

VPOS

D23

E1

E2

E3

E4

IN16

IP1

IN0

VNEG

VOCM

Input Number 16, Negative Phase.

Input Number 1, Positive Phase.

Input Number 0, Negative Phase.

Analog Negative Power Supply.

Output Common-Mode Reference

Supply.

E20

VOCM

Output Common-Mode Reference

Supply.

E21

E22

E23

F1

F2

F3

VNEG

IN17

IP16

IN1

IP2

VNEG

VDD

VNEG

IP17

IN18

IP3

IN2

VNEG

DGND

VNEG

IN19

IP18

Analog Negative Power Supply.

Input Number 17, Negative Phase.

Input Number 16, Positive Phase.

Input Number 1, Negative Phase.

Input Number 2, Positive Phase.

Analog Negative Power Supply.

Logic Positive Power Supply.

F4

F20

F21

F22

F23

G1

G2

G3

G4

G20

G21

G22

G23

H1

H2

H3

H4

H20

H21

H22

H23

J1

J2

J3

J4

Logic Positive Power Supply.

Analog Negative Power Supply.

Input Number 17, Positive Phase.

Input Number 18, Negative Phase.

Input Number 3, Positive Phase.

Input Number 2, Negative Phase.

Analog Negative Power Supply.

Logic Negative Power Supply.

Analog Negative Power Supply.

Input Number 19, Negative Phase.

Input Number 18, Positive Phase.

Input Number 3, Negative Phase.

Input Number 4, Positive Phase.

Analog Negative Power Supply.

Control Pin: Serial Data Out.

Control Pin: Second Rank Data Reset.

Analog Negative Power Supply.

Input Number 19, Positive Phase.

Input Number 20, Negative Phase.

Input Number 5, Positive Phase.

Input Number 4, Negative Phase.

Analog Negative Power Supply.

Control Pin: Serial Data Clock.

Control Pin: Second Rank Write Strobe.

IN3

IP4

VNEG

DATA OUT

RESET

VNEG

IP19

IN20

IP5

IN4

D2

D3

D4

D5

VPOS

VNEG

VOCM

Output Common-Mode Reference

Supply.

D6

D7

D8

D9

D10

D11

VNEG

VPOS

Analog Negative Power Supply.

Analog Positive Power Supply.

VNEG

CLK

J20

UPDATE

Rev. A | Page 10 of 36

AD8117/AD8118

Ball No. Mnemonic Description

J21

J22

J23

K1

K2

K3

VNEG

IN21

IP20

IN5

Analog Negative Power Supply.

Input Number 21, Negative Phase.

Input Number 20, Positive Phase.

Input Number 5, Negative Phase.

Input Number 6, Positive Phase.

Analog Negative Power Supply.

Control Pin: Serial Data In.

T2

T3

T4

T20

T21

T22

T23

IP12

VNEG

A0

Input Number 12, Positive Phase.

Analog Negative Power Supply.

Control Pin: Output Address Bit 0.

Control Pin: Input Address Bit 0.

Analog Negative Power Supply.

Input Number 27, Positive Phase.

Input Number 28, Negative Phase.

D0

IP6

VNEG

IP27

IN28

VNEG

DATA IN

WE

K4

K20

K21

K22

K23

L1

L2

L3

L4

Control Pin: First Rank Write Strobe.

Analog Negative Power Supply.

Input Number 21, Positive Phase.

Input Number 22, Negative Phase.

Input Number 7, Positive Phase.

Input Number 6, Negative Phase.

Analog Positive Power Supply.

Control Pin: Serial/Parallel Mode Select.

Control Pin: Input Address Bit 5.

Analog Positive Power Supply.

Input Number 23, Negative Phase.

Input Number 22, Positive Phase.

Input Number 7, Negative Phase.

Input Number 8, Positive Phase.

Analog Positive Power Supply.

Control Pin: Output Address Bit 4.

Control Pin: Input Address Bit 4.

Analog Positive Power Supply.

Input Number 23, Positive Phase.

Input Number 24, Negative Phase.

Input Number 9, Positive Phase.

Input Number 8, Negative Phase.

Analog Positive Power Supply.

Control Pin: Output Address Bit 3.

Control Pin: Input Address Bit 3.

Analog Positive Power Supply.

Input Number 25, Negative Phase.

Input Number 24, Positive Phase.

Input Number 9, Negative Phase.

Input Number 10, Positive Phase.

Analog Negative Power Supply.

Control Pin: Output Address Bit 2.

Control Pin: Input Address Bit 2.

Analog Negative Power Supply.

Input Number 25, Positive Phase.

Input Number 26, Negative Phase.

Input Number 11, Positive Phase.

Input Number 10, Negative Phase.

Analog Negative Power Supply.

Control Pin: Output Address Bit 1.

Control Pin: Input Address Bit 1.

Analog Negative Power Supply.

Input Number 27, Negative Phase.

Input Number 26, Positive Phase.

Input Number 11, Negative Phase.

U1

IP13

Input Number 13, Positive Phase.

Input Number 12, Negative Phase.

Analog Negative Power Supply.

Logic Positive Power Supply.

VNEG

IP21

IN22

IP7

U2

U3

U4

U20

U21

U22

U23

IN12

VNEG

VDD

VNEG

IN29

IP28

Logic Positive Power Supply.

IN6

Analog Negative Power Supply.

Input Number 29, Negative Phase.

Input Number 28, Positive Phase.

VPOS

SER/PAR

D5

VPOS

IN23

IP22

IN7

IP8

VPOS

A4

L20

L21

L22

L23

M1

M2

M3

M4

M20

M21

M22

M23

N1

N2

N3

N4

N20

N21

N22

N23

P1

P2

P3

P4

P20

P21

P22

P23

R1

R2

R3

R4

R20

R21

R22

R23

T1

V1

V2

V3

V4

V20

V21

V22

V23

W1

W2

W3

W4

IN13

IP14

Input Number 13, Negative Phase.

Input Number 14, Positive Phase.

Analog Negative Power Supply.

Logic Negative Power Supply.

Analog Negative Power Supply.

Input Number 29, Positive Phase.

Input Number 30, Negative Phase.

Input Number 15, Positive Phase.

Input Number 14, Negative Phase.

Analog Negative Power Supply.

Output Common-Mode Reference

Supply.

Output Common-Mode Reference

Supply.

Analog Negative Power Supply.

Input Number 31, Negative Phase.

Input Number 30, Positive Phase.

Input Number 15, Negative Phase.

Analog Positive Power Supply.

Analog Negative Power Supply.

VNEG

DGND

VNEG

IP29

IN30

IP15

IN14

VNEG

VOCM

D4

VPOS

IP23

IN24

IP9

IN8

VPOS

A3

W20

VOCM

W21

W22

W23

Y1

Y2

Y3

VNEG

IN31

IP30

D3

VPOS

IN25

IP24

IN9

IP10

VNEG

A2

IN15

VPOS

VNEG

VOCM

Y4

Y5

Output Common-Mode Reference

Supply.

Y6

Y7

Y8

Y9

Y10

Y11

Y12

Y13

Y14

Y15

Y16

Y17

Y18

VNEG

VPOS

VNEG

Analog Negative Power Supply.

Analog Positive Power Supply.

Analog Negative Power Supply.

D2

VNEG

IP25

IN26

IP11

IN10

VNEG

A1

D1

VNEG

IN27

IP26

IN11

Rev. A | Page 11 of 36

AD8117/AD8118

Ball No. Mnemonic Description

Y19

VOCM

Output Common-Mode Reference

Supply.

AB10

AB11

AB12

AB13

AB14

AB15

AB16

AB17

AB18

AB19

AB20

AB21

AB22

AB23

AC1

OP6

ON6

OP8

ON8

Output Number 6, Positive Phase.

Output Number 6, Negative Phase.

Output Number 8, Positive Phase.

Output Number 8, Negative Phase.

Output Number 10, Positive Phase.

Output Number 10, Negative Phase.

Output Number 12, Positive Phase.

Output Number 12, Negative Phase.

Output Number 14, Positive Phase.

Output Number 14, Negative Phase.

Analog Positive Power Supply.

Output Number 1, Positive Phase.

Output Number 1, Negative Phase.

Output Number 3, Positive Phase.

Output Number 3, Negative Phase.

Output Number 5, Positive Phase.

Output Number 5, Negative Phase.

Output Number 7, Positive Phase.

Output Number 7, Negative Phase.

Output Number 9, Positive Phase.

Output Number 9, Negative Phase.

Output Number 11, Positive Phase.

Output Number 11, Negative Phase.

Output Number 13, Positive Phase.

Output Number 13, Negative Phase.

Output Number 15, Positive Phase.

Output Number 15, Negative Phase.

Analog Positive Power Supply.

Y20

Y21

Y22

Y23

VNEG

VPOS

IP31

Analog Negative Power Supply.

Analog Positive Power Supply.

Input Number 31, Positive Phase.

Analog Positive Power Supply.

Analog Negative Power Supply.

Analog Positive Power Supply.

Analog Negative Power Supply.

Analog Positive Power Supply.

Output Number 0, Positive Phase.

Output Number 0, Negative Phase.

Output Number 2, Positive Phase.

Output Number 2, Negative Phase.

Output Number 4, Positive Phase.

Output Number 4, Negative Phase.

OP10

ON10

OP12

ON12

OP14

ON14

VPOS

OP1

VPOS

VNEG

VPOS

VNEG

VPOS

OP0

AA1

AA2

AA3

AA4

AA5

AA6

AA7

AA8

AA9

AA10

AA11

AA12

AA13

AA14

AA15

AA16

AA17

AA18

AA19

AA20

AA21

AA22

AA23

AB1

AC2

AC3

AC4

AC5

AC6

ON1

AC7

AC8

AC9

OP3

ON3

OP5

ON5

AC10

AC11

AC12

AC13

AC14

AC15

AC16

AC17

AC18

AC19

AC20

AC21

AC22

AC23

OP7

ON7

OP9

ON9

OP11

ON11

OP13

ON13

OP15

ON15

VPOS

AB2

AB3

AB4

AB5

AB6

AB7

AB8

AB9

ON0

OP2

ON2

OP4

Analog Positive Power Supply.

ON4

Rev. A | Page 12 of 36

AD8117/AD8118

TRUTH TABLE AND LOGIC DIAGRAM

Table 9. Operation Truth Table

DATA

INPUT

DATA

OUTPUT

WE

UPDATE

CLK

RESET

SER/PAR

Operation/Comment

X

0

X

Asynchronous reset. All outputs are

disabled. Remainder of logic in 192-bit shift

register is unchanged.

0

1

X

D0…D5¹

Data_i²

NA in

parallel

mode

1

0

Broadcast. The data on parallel lines D0 to

D5 are loaded into all 32 output address

locations of the 192-bit shift register.

Serial mode. The data on the serial DATA IN

line is loaded into the serial register. The first

bit clocked into the serial register appears

at DATA OUT 192 clock cycles later.

Data_i-192

0

1

X

0

X

D0…D5¹

A0…A4³

NA in

parallel

mode

NA in

parallel

mode

1

X

1

Parallel programming mode. The data on

parallel lines D0 to D5 are loaded into the

shift register location addressed by A0 to A4.

Switch matrix update. Data in the 192-bit

shift register transfers into the parallel

latches that control the switch array.

X

No change in logic.

¹D0…D5: data bits.

²Data_i: serial data.

³A0…A4: address bits.

Rev. A | Page 13 of 36

AD8117/AD8118

0 0 7 6 5 6 - 0 3

R E D O C E

E S D R A D

D 3 2 T O 5

S

T U P T O U

Figure 7. Logic Diagram

Rev. A | Page 14 of 36

AD8117/AD8118

I/O SCHEMATICS

IPn

INn

1.3pF

2500Ω

OPn, ONn

0.3pF

Figure 8. AD8117/AD8118 Enabled Output

(see also ESD Protection Map, Figure 18)

Figure 12. AD8117/AD8118 Receiver Simplified Equivalent Circuit When

Driving Differentially

OPn

IPn

3.4pF

3.33kΩ AD8117 G = +1

3.76kΩ AD8118 G = +2

1.6pF

0.4pF

30kΩ

INn

3.4pF

ONn

Figure 13. AD8117/AD8118 Receiver Simplified Equivalent Circuit When

Driving Single-Ended

Figure 9. AD8117/AD8118 Disabled Output

(see also ESD Protection Map, Figure 18)

2500Ω

1.3pF

2538Ω

IPn

INn

VOCM

0.3pF

1.3pF

2500Ω

VNEG

2538Ω

Figure 14. VOCM Input (see also ESD Protection Map, Figure 18)

Figure 10. AD8117 Receiver (see also ESD Protection Map, Figure 18)

2500Ω

5075Ω

IPn

INn

VDD

1.3pF

25kΩ

1kΩ

0.3pF

RESET

1.3pF

2500Ω

DGND

Figure 11. AD8118 Receiver (see also ESD Protection Map, Figure 18)

Figure 15. Reset Input (see also ESD Protection Map, Figure 18)

Rev. A | Page 15 of 36

AD8117/AD8118

VPOS

VDD

CLK, RESET,

SER/PAR, WE,

UPDATE,

DATA IN,

DATA OUT,

A[4:0], D[5:0]

IPn, INn,

OPn, ONn,

VOCM

CLK, SER/PAR, WE,

UPDATE, DATA IN,

A[4:0], D[5:0]

1kΩ

DGND

VNEG

DGND

Figure 16. Logic Input (see also ESD Protection Map, Figure 18)

Figure 18. ESD Protection Map

VDD

DATA OUT

DGND

Figure 17. Logic Output (see also ESD Protection Map, Figure 18)

Rev. A | Page 16 of 36

AD8117/AD8118

TYPICAL PERFORMANCE CHARACTERISTICS

V_S= 2.5 V at T_A= 25°C, R_{L, diff}= 200 Ω, V_OCM= 0 V, differential I/O mode, unless otherwise noted.

10

8

400

350

300

250

200

150

100

50

AD8118

6

4

2

AD8117

0

–2

–4

–6

–8

–10

0

540

560

580

600

620

640

660

680

700

1

10

100

1000

FREQUENCY (MHz)

Figure 19. AD8117, AD8118 Small Signal Frequency Response, 200 mV p-p

Figure 22. AD8117 −3 dB Bandwidth Histogram,

One Device, All 1024 Channels

10

0

–1

–2

–3

8

AD8118

6

4

2

AD8117

0

–2

–4

–6

–8

–10

1

10

100

1000

2

4

6

8

10 12 14 16 18 20 22 24 26 28 30 32

FREQUENCY (MHz)

NUMBER OF ENABLED CHANNELS

Figure 20. AD8117, AD8118 Large Signal Frequency Response, 2 V p-p

Figure 23. AD8117 Bandwidth Error vs. Enabled Channels

10

8

0

DIFFERENTIAL OUT

–10

6

10pF

5pF

–20

–30

–40

–50

–60

–70

4

2

2pF

0

–2

0pF

–4

–6

–8

–10

0

10

100

1000

300k

1M

10M

100M

1G 2G

FREQUENCY (MHz)

FREQUENCY (Hz)

Figure 21. AD8117 Small Signal Frequency Response with Capacitive Loads,

200 mV p-p

Figure 24. AD8117, AD8118 Common-Mode Rejection

Rev. A | Page 17 of 36

AD8117/AD8118

–15

0

–20

DIFFERENTIAL IN/OUT

DIFFERENTIAL OUT

–25

V

AGGRESSOR

NEG

–35

V

AGGRESSOR

POS

–45

–55

–65

–75

–85

–95

–40

V

AGGRESSOR

OCM

–60

–80

–100

0.1

1

10

FREQUENCY (MHz)

100

1000

300k

1M

10M

FREQUENCY (Hz)

100M

1G

Figure 25. AD8117 Power Supply Rejection

Figure 28. AD8117 Crosstalk, One Adjacent Channel

10

5

0

–20

SINGLE-ENDED OUT

DIFFERENTIAL IN/OUT

0

–5

V

AGGRESSOR

OCM

–10

–15

–20

–25

–30

–35

–40

–45

–50

–40

V

AGGRESSOR

NEG

–60

V

AGGRESSOR

POS

10

–80

–100

300k

0.1

1

100

1000

1M

10M

100M

1G

FREQUENCY (MHz)

FREQUENCY (Hz)

Figure 29. AD8118 Crosstalk, One Adjacent Channel

Figure 26. AD8117 Power Supply Rejection, Single-Ended

0

–20

180

SINGLE-ENDED IN/OUT

DIFFERENTIAL OUT

160

140

120

100

80

–40

AD8118

AD8117

–60

60

40

–80

20

–100

300k

0

1k

1M

10M

100M

1G

10k

100k

FREQUENCY (Hz)

1M

FREQUENCY (Hz)

Figure 30. AD8117 Crosstalk, One Adjacent Channel, Single-Ended

Figure 27. AD8117, AD8118 Noise Spectral Density, RTO

Rev. A | Page 18 of 36

AD8117/AD8118

0

–20

0

–20

SINGLE-ENDED IN/OUT

–40

–60

–80

–100

300k

1M

10M

100M

1G

300k

1M

10M

FREQUENCY (Hz)

100M

1G

FREQUENCY (Hz)

Figure 31. AD8118 Crosstalk, One Adjacent Channel, Single-Ended

Figure 34. AD8117 Crosstalk, All Hostile, Single-Ended

0

–20

SINGLE-ENDED IN/OUT

DIFFERENTIAL IN/OUT

–20

–40

–60

–80

–100

300k

–100

300k

1M

10M

100M

1G

1M

10M

100M

1G

FREQUENCY (Hz)

Figure 35. AD8118 Crosstalk, All Hostile, Single-Ended

Figure 32. AD8117 Crosstalk, All Hostile

0

–20

0

DIFFERENTIAL IN/OUT

–20

–40

–60

–80

–100

300k

1M

10M

100M

1G 2G

300k

1M

10M

100M

1G

FREQUENCY (Hz)

Figure 33. AD8118 Crosstalk, All Hostile

Figure 36. AD8117 Crosstalk, Off Isolation

Rev. A | Page 19 of 36

AD8117/AD8118

0

30k

25k

20k

15k

10k

5k

SINGLE-ENDED IN/OUT

DIFFERENTIAL OUT

–20

–40

–60

–80

–100

0

300k

1M

10M

100M

1G 2G

100k

1M

10M

100M

1G

FREQUENCY (Hz)

Figure 37. AD8117 Crosstalk, Off Isolation, Single-Ended

Figure 40. AD8117, AD8118 Output Impedance, Disabled

6k

1000

DIFFERENTIAL IN

AD8118

AD8117

5k

4k

3k

2k

1k

0

100

10

1

0.1

300k

1M

10M

100M

1G

100k

1M

10M

100M

1G

FREQUENCY (Hz)

Figure 38. AD8117, AD8118 Input Impedance

Figure 41. AD8117, AD8118 Output Impedance, Enabled

4500

4000

3500

3000

2500

2000

1500

1000

500

0.4

SINGLE-ENDED IN

AD8118

AD8117

0.3

0.2

0.1

0

–0.1

–0.2

–0.3

–0.4

0

1

2

3

4

5

6

7

8

9

10 11 12 13 14 15

300k

1M

10M

100M

1G

FREQUENCY (Hz)

TIME (ns)

Figure 39. AD8117, AD8118 Input Impedance, Single-Ended

Figure 42. AD8117 Small Signal Pulse Response, 200 mV p-p

Rev. A | Page 20 of 36

AD8117/AD8118

1.5

1.0

3

0.20

0.15

0.10

0.05

0

UPDATE

2

N-CHANNEL

P-CHANNEL

0.5

1

0

–0.05

–0.10

–0.15

–0.20

–0.5

–1.0

–1.5

–1

–2

–3

V

OUT

0

1

2

3

4

5

6

7

8

9

10 11 12 13 14 15

–40

–20

0

20

40

60

80

100

120

TIME (ns)

Figure 46. AD8117 Switching Time

Figure 43. AD8117 Small Signal Pulse Response, Single-Ended, 200 mV p-p

2

1

5000

4000

3000

2000

1000

0

2.0

1.5

1.0

0

0.5

V

OUT

–1

–2

–3

–4

0

–0.5

–1.0

–1.5

–2.0

SLEW RATE

1

–1000

0

1

2

3

4

5

6

7

8

9

10 11 12 13 14 15

0

2

3

4

5

TIME (ns)

Figure 47. AD8117 Large Signal Rising Edge and Slew Rate

Figure 44. AD8117 Large Signal Pulse Response, 2 V p-p

2

1

3500

1.0

V

0.8

0.6

OUT

2500

1500

500

0.4

N-CHANNEL

P-CHANNEL

0

0.2

–1

–2

–3

–4

0

SLEW RATE

–0.2

–0.4

–0.6

–0.8

–1.0

–500

–1500

–2500

0

1

2

3

4

5

0

1

2

3

4

5

6

7

8

9

10 11 12 13 14 15

1ns/DIV

TIME (ns)

Figure 48. AD8117 Large Signal Falling Edge and Slew Rate

Figure 45. AD8117 Large Signal Pulse Response, Single-Ended, 2 V p-p

Rev. A | Page 21 of 36

AD8117/AD8118

0.014

0.012

0.010

0.008

0.006

0.004

0.002

0

5

4

3

2

1

0

–0.002

–0.004

–700

–500

–300

–100

100

300

500

700

–40 –30 –20 –10

0

10 20 30 40 50 60 70 80 90 100

TEMPERATURE (ºC)

V

, DIFF (mV)

IN

Figure 49. AD8117 V_OSvs. Temperature in Broadcast Mode

Figure 52. AD8117 Phase vs. DC Voltage, Carrier Frequency = 3.58 MHz,

Subcarrier Amplitude = 600 mV p-p, Differential

50

2.0

10pF

1.5

40

30

5pF

1.0

2pF

0.5

20

0pF

0

10

–0.5

–1.0

–1.5

–2.0

0

–10

–20

–0.10 –0.08 –0.06 –0.04 –0.02

0

0.02 0.04 0.06 0.08 0.10

0

2

4

6

8

10

12

14

16

18

TIME (µs)

TIME (ns)

Figure 50. AD8117 Switching Transient (Glitch)

Figure 53. AD8117 Large Signal Pulse Response with Capacitive Loads

0.020

0.015

0.010

0.005

0

0.4

10pF

0.3

5pF

0.2

2pF

0.1

0pF

0

–0.1

–0.2

–0.3

–0.4

–0.005

–0.010

–700

–500

–300

–100

100

300

500

700

0

2

4

6

8

10

12

14

16

18

V

, DIFF (mV)

IN

TIME (ns)

Figure 51. AD8117 Gain vs. DC Voltage, Carrier Frequency = 3.58 MHz,

Subcarrier Amplitude = 600 mV p-p, Differential

Figure 54. AD8117 Small Signal Pulse Response with Capacitive Loads

Rev. A | Page 22 of 36

AD8117/AD8118

1.4

1.2

1.0

0.8

0.6

0.4

0.2

0

2.8

2.4

2.0

1.6

1.2

0.8

0.4

0

600

500

400

300

200

100

900

I

AND I

(BROADCAST)

NEG

POS

UPDATE

800

I

(SERIAL MODE)

DD

700

600

500

400

I

(PARALLEL MODE)

DD

V

OUT

I

AND I

NEG

POS

(ALL OUTPUTS DISABLED)

–0.2

–50 –30 –10

–0.4

110 130 150

–35 –25 –15 –5

5

15 25 35 45 55 65 75 85 95

10

30

50

70

90

TEMPERATURE (°C)

TIME (ns)

Figure 58. AD8117, AD8118 Quiescent Supply Currents vs. Temperature

Figure 55. AD8117 Enable Time

500

450

400

350

300

250

200

950

900

850

800

750

700

650

600

550

500

450

1.4

2.8

2.4

2.0

1.6

1.2

0.8

0.4

0

I

, I

POS NEG

UPDATE

1.2

1.0

0.8

0.6

0.4

0.2

0

V

OUT

I

SERIAL

DD

PARALLEL

DD

–0.2

–50 –30 –10

–0.4

110 130 150

4

8

12

16

20

24

28

32

10

30

50

70

90

CHANNELS

TIME (ns)

Figure 59. AD8117, AD8118 Quiescent Supply Currents vs. Enabled Outputs

Figure 56. AD8117 Disable Time

65

60

55

50

45

40

35

30

25

20

15

10

5

3.25

3.00

2.75

2.50

2.25

2.00

1.75

1.50

1.25

1.00

0.75

0.50

0.25

0

(V

– V )/V

IN OUT

OUT

–0.01

V

IN

–0.02

–0.03

–0.04

–0.05

V

OUT

0

–5

–0.25

0

1

2

3

4

5

6

7

–50

–25

0

25

50

75

100

TIME (ns)

TEMPERATURE (ºC)

Figure 60. AD8117 Settling Time

Figure 57. AD8117 DC Gain vs. Temperature

Rev. A | Page 23 of 36

AD8117/AD8118

5

2.0

1.5

4

V

OUTP

3

1.0

2

0.5

1

V

INP

0

–1

–2

–3

–4

–5

–0.5

–1.0

–1.5

–2.0

V

OUTN

V

INN

0

1

2

3

4

5

6

7

0

100

200

300

400

500

600

700

TIME (ns)

Figure 61. AD8117 Settling Time (Zoom)

Figure 63. AD8118 Overdrive Recovery, Single-Ended

2.5

2.0

–30

–40

–50

–60

–70

–80

–90

–100

V

= 2V p-p, DIFF

OUT

V

INP

V

OUTP

1.5

1.0

THIRD

HARMONIC

0.5

0

–0.5

–1.0

–1.5

–2.0

–2.5

SECOND

HARMONIC

V

OUTN

V

INN

0

100

200

300

400

500

600

700

0.1

1

10

FREQUENCY (MHz)

100

1000

TIME (ns)

Figure 62. AD8117 Overdrive Recovery, Single-Ended

Figure 64. AD8117 Harmonic Distortion

Rev. A | Page 24 of 36

AD8117/AD8118

THEORY OF OPERATION

The AD8117/AD8118 are fully differential crosspoint arrays

with 32 outputs, each of which can be connected to any one of

32 inputs. Organized by output row, 32 switchable input trans-

conductance stages are connected to each output buffer to form

32-to-1 multiplexers. There are 32 of these multiplexers, each

with its inputs wired in parallel, for a total array of 1024

transconductance stages forming a multicast-capable

crosspoint switch.

The outputs of the AD8117/AD8118 can be disabled to

minimize on-chip power dissipation. When disabled, there is a

feedback network of 25 kꢀ between the differential outputs.

This high impedance allows multiple ICs to be bussed together

without additional buffering. Care must be taken to reduce

output capacitance, which results in more overshoot and

frequency domain peaking. A series of internal amplifiers drive

internal nodes such that a wideband high impedance is

presented at the disabled output, even while the output bus is

under large signal swings. When the outputs are disabled and

driven externally, the voltage applied to them should not exceed

the valid output swing range for the AD8117/AD8118 in order

to keep these internal amplifiers in their linear range of

operation. Applying excess differential voltages to the disabled

outputs can cause damage to the AD8117/AD8118 and should

be avoided (see the Absolute Maximum Ratings section for

guidelines).

Decoding logic for each output selects one (or none) of the

transconductance stages to drive the output stage. The enabled

transconductance stage drives the output stage, and feedback

forms a closed-loop amplifier with a differential gain of one (the

difference between the output voltages is equal to the difference

between the input voltages). A second feedback loop controls

the common-mode output level, forcing the average of the

differential output voltages to match the voltage on the VOCM

reference pin. Although each output has an independent

common-mode control loop, the VOCM reference is common

for the entire chip, and as such needs to be driven with a low

impedance to avoid crosstalk.

The connection of the AD8117/AD8118 is controlled by a

flexible TTL-compatible logic interface. Either parallel or serial

loading into a first rank of latches preprograms each output. A

global update signal moves the programming data into the

second rank of latches, simultaneously updating all outputs. In

serial mode, a serial-out pin allows devices to be daisy-chained

together for single-pin programming of multiple ICs. A power-

on reset pin is available to avoid bus conflicts by disabling all

outputs. This power-on reset clears the second rank of latches,

but does not clear the first rank of latches. In parallel mode, to

quickly clear the first rank, a broadcast parallel programming

feature is available. In serial mode, preprogramming individual

inputs is not possible and the entire shift register needs to

be flushed.

Each differential input to the AD8117/AD8118 is buffered by a

receiver. The purpose of this receiver is to provide an extended

input common-mode range, and to remove this common mode

from the signal chain. Like the output multiplexers, the input

receiver has both a differential loop and a common-mode

control loop. A mask-programmable feedback network sets the

closed-loop differential gain. For the AD8117, this differential

gain is one, and for the AD8118, this differential gain is two.

The receiver has an input stage that does not respond to the

common mode of the signal. This architecture, along with the

attenuating feedback network, allows the user to apply input

voltages that extend from rail-to-rail. Excess differential loop

gain bandwidth product reduces the effect of the closed-loop

gain on the bandwidth of the device.

The AD8117/AD8118 can operate on a single +5 V supply,

powering both the signal path (with the VPOS/VNEG supply

pins), and the control logic interface (with the VDD/DGND

supply pins). However, to easily interface to ground-referenced

video signals, split supply operation is possible with 2.5 V

supplies. In this case, a flexible logic interface allows the control

logic supplies (VDD/DGND) to be run off +2 V/0 V to

+5 V/0 V while the core remains on split supplies. Additional

flexibility in the analog output common-mode level facilitates

unequal split supplies. If +3 V/–2 V supplies to +2 V/–3 V

supplies are desired, the VOCM pin can still be set to 0 V for

ground-referenced video signals.

The output stage of the AD8117/AD8118 is designed for low

differential gain and phase error when driving composite video

signals. It also provides slew current for fast pulse response

when driving component video signals. Unlike many multi-

plexer designs, these requirements are balanced such that large

signal bandwidth is very similar to small signal bandwidth. The

design load is 150 ꢀ, but provisions are made to drive loads

as low as 75 ꢀ so long as on-chip power dissipation limits are

not exceeded.

Rev. A | Page 25 of 36

AD8117/AD8118

APPLICATIONS

the programming sequence is 192 bits times the number of

devices in the chain.

PROGRAMMING

The AD8117/AD8118 have two options for changing the

programming of the crosspoint matrix. In the first option, a

serial word of 192 bits can be provided that updates the entire

matrix each time. The second option allows for changing the

programming of a single output via a parallel interface. The

serial option requires fewer signals, but more time (clock cycles)

for changing the programming, while the parallel programming

technique requires more signals, but can change a single output

at a time and requires fewer clock cycles to complete

programming.

Parallel Programming Description

When using the parallel programming mode, it is not necessary

to reprogram the entire device when making changes to the matrix.

In fact, parallel programming allows the modification of a

WE UPDATE

single output at a time. Because this takes only one

/

cycle, significant time savings can be realized by using parallel

programming.

One important consideration in using parallel programming is

RESET

that the

signal does not reset all registers in the AD8117/

RESET

Serial Programming Description

AD8118. When taken low, the

signal only sets each

CLK

The serial programming mode uses the

UPDATE SER

, DATA IN,

output to the disabled state. This is helpful during power-up to

ensure that two parallel outputs are not active at the same time.

, and

/PAR device pins. The first step is to assert a

/PAR in order to enable the serial programming

SER

low on

After initial power-up, the internal registers in the device

WE

mode. The parallel clock

entire serial programming operation.

should be held high during the

RESET

generally have random data, even though the

signal has

been asserted. If parallel programming is used to program one

output, then that output will be properly programmed, but the

rest of the device will have a random program state depending

on the internal register content at power-up. Therefore, when

using parallel programming, it is essential that all outputs be

programmed to a desired state after power-up. This ensures that

the programming matrix is always in a known state. From then

on, parallel programming can be used to modify a single output

or more at a time.

UPDATE

The

shifted into the serial port of the device. Although the data still

UPDATE

signal should be high during the time that data is

shifts in when

is low, the transparent, asynchronous

latches allow the shifting data to reach the matrix. This causes

the matrix to try to update to every intermediate state as

defined by the shifting data.

CLK

The data at DATA IN is clocked in at every falling edge of

.

A total of 192 bits must be shifted in to complete the program-

ming. For each of the 32 outputs, there are five bits (D0 to D4)

that determine the source of its input followed by one bit (D5)

that determines the enabled state of the output. If D5 is low

(output disabled), the five associated bits (D0 to D4) do not

matter, because no input is switched to that output.

UPDATE

In similar fashion, if

is taken low after initial power-

up, the random power-up data in the shift register will be

programmed into the matrix. Therefore, in order to prevent the

crosspoint from being programmed into an unknown state, do

UPDATE

not apply a low logic level to

after power is initially

applied. Programming the full shift register one time to a

desired state, by either serial or parallel programming after

initial power-up, eliminates the possibility of programming the

matrix to an unknown state.

The most significant output address data is shifted in first, with

the enable bit (D5) shifted in first, followed by the input address

(D4 to D0) entered sequentially with D4 first and D0 last. Each

remaining output is programmed sequentially, until the least

significant output address data is shifted in. At this point,

To change the programming of an output via parallel program-

SER

UPDATE

CLK

ming,

programming clock,

/PAR and

should be taken high. The serial

, should be left high during parallel

UPDATE

can be taken low, which causes the programming of

the device according to the data that was just shifted in. The

UPDATE UPDATE

WE

programming. The parallel clock,

, should start in the high

latches are asynchronous and when

they are transparent.

is low,

state. The 5-bit address of the output to be programmed should

be put on A0 to A4. The first five data bits (D0 to D4) should

contain the information that identifies the input that is pro-

grammed to the output that is addressed. The sixth data bit

(D5) determines the enabled state of the output. If D5 is low

(output disabled), then the data on D0 to D4 does not matter.

If more than one AD8117/AD8118 device is to be serially

programmed in a system, the DATA OUT signal from one

device can be connected to the DATA IN of the next device to

CLK UPDATE SER

form a serial chain. All of the

,

, and /PAR

pins should be connected in parallel and operated as described

previously. The serial data is input to the DATA IN pin of the

first device of the chain, and it ripples through to the last.

Therefore, the data for the last device in the chain should come

at the beginning of the programming sequence. The length of

After the desired address and data signals have been established,

they can be latched into the shift register by a high to low

WE

transition of the

signal. The matrix is not programmed,

UPDATE

however, until the

signal is taken low. It is thus possible

to latch in new data for several or all of the outputs first via

Rev. A | Page 26 of 36

AD8117/AD8118

WE

UPDATE

The receivers respond only to the difference in input voltages,

and will restore a common-mode voltage suitable for the

internal signal path. Noise or crosstalk that is present in both

inputs is rejected by the input stage, as specified by its common-

mode rejection ratio (CMRR). Differential operation offers a

great noise benefit for signals that are propagated over distance

in a noisy environment.

successive negative transitions of

while

is held

UPDATE

high, and then have all the new data take effect when

goes low. This technique should be used when programming

the device for the first time after power-up when using parallel

programming.

Reset

When powering up the AD8117/AD8118, it is usually desirable

R

F

RESET

to have the outputs come up in the disabled state. The

pin, when taken low, causes all outputs to be in the disabled state.

UPDATE

AD8117/AD8118. This is important when operating in the

parallel programming mode. Refer to the Parallel Programming

Description section for information about programming internal

registers after power-up. Serial programming programs the entire

matrix each time; therefore, no special considerations apply.

R

G

IN+

VOCM

IN–

OUT–

However, the

signal does not reset all registers in the

RCVR

TO SWITCH MATRIX

OUT+

R

F

Figure 65. Input Receiver Equivalent Circuit

The circuit configuration used by the differential input receivers

is similar to that of several Analog Devices, Inc. general-

purpose differential amplifiers, such as the AD8131. It is a

voltage feedback amplifier with internal gain setting resistors.

The arrangement of feedback makes the differential input

impedance appear to be 5 kꢀ across the inputs.

Since the data in the shift register is random after power-up, it

should not be used to program the matrix, or the matrix can

enter unknown states. To prevent this, do not apply a logic low

UPDATE

signal to

initially after power-up. The shift register

UPDATE

should first be loaded with the desired data, and then

can be taken low to program the device.

R_IN,dm= 2 × R_G= 5 kꢀ

RESET

The

pin has a 20 kꢀ pull-up resistor to VDD that can be

This impedance creates a small differential termination error if

the user does not account for the 5 kꢀ parallel element, although

this error is less than 1% in most cases. Additionally, the source

impedance driving the AD8117/AD8118 appears in parallel

with the internal gain-setting resistors, such that there may be a

gain error for some values of source resistance. The AD8117/

AD8118 are adjusted such that its gains are correct when driven

by a back-terminated 75 ꢀ source impedance at each input

phase (37.5 ꢀ effective impedance to ground at each input pin,

or 75 ꢀ differential source impedance across pairs of input

pins). If a different source impedance is presented, the differential

gain of the AD8117/AD8118 can be calculated by

used to create a simple power-up reset circuit. A capacitor from

RESET RESET

of the device stabilizes. The low condition causes all the outputs

to be disabled. The capacitor then charges through the pull-up

resistor to the high state, thus allowing full programming

capability of the device.

to ground holds

low for some time while the rest

Broadcast

The AD8117/AD8118 logic interface has a broadcast mode, in

which all first rank latches can be simultaneously parallel-

programmed to the same data in one write cycle. This is especially

useful in clearing random first rank data after power-up. To

access the broadcast mode, the part is parallel programmed

V_OUT,dm

R_F

G_dm

=

WE

UPDATE

/PAR pin is held low, as if

using the

The only difference is that the

serial programming. By holding

, A0 to A4, D0 to D5, and

device pins.

V_IN,dm

R_G+ R_S

SER

CLK

where:

R_G= 2.5 kꢀ.

high, no serial clocking

WE

occurs, and instead,

can be used to clock all first rank

R_Sis the user single-ended source resistance (such as 37.5 ꢀ for

a back-terminated 75 ꢀ source).

R_F= 2.538 kꢀ for the AD8117 and 5.075 kꢀ for the AD8118.

latches in the chip at once.

OPERATING MODES

The AD8117/AD8118 has fully differential inputs and outputs.

The inputs and outputs can also be operated in a single-ended

fashion. This presents several options for circuit configurations

that require different gains and treatment of terminations, if

they are used.

In the case of the AD8117,

2.538 kꢀ

G_dm

=

2.5 kꢀ+ R_S

In the case of the AD8118,

5.075 kꢀ

Differential Input

G_dm

=

Each differential input to the AD8117/AD8118 is applied to a

differential receiver. These receivers allow the user to drive the

inputs with a differential signal with an uncertain common-

mode voltage, such as from a remote source over twisted pair.

2.5 kꢀ+ R_S

When operating with a differential input, care must be taken to

keep the common mode, or average, of the input voltages within

Rev. A | Page 27 of 36

AD8117/AD8118

R_G+ R_S

the linear operating range of the AD8117/AD8118 receiver. This

common-mode range can extend rail-to-rail, provided the

differential signal swing is small enough to avoid forward

biasing the ESD diodes (it is safest to keep the common mode

plus differential signal excursions within the supply voltages of

the part). See the Specifications section for guaranteed input

range.

R_IN

=

R_F

1 −

2 × (R_G+ R_S+ R_F)

where:

R_G= 2.5 kꢀ.

R_Sis the user single-ended source resistance (such as 37.5 ꢀ for

a back-terminated 75 ꢀ source).

The differential output of the AD8117/AD8118 receiver is

linear for a peak of 1.4 V of output voltage difference (1.4 V

peak input difference for the AD8117, and 0.7 V peak input

difference for the AD8118). Taking the output differentially,

using the two output phases, this allows 2.8 V p-p of linear

output signal swing. Beyond this level, the signal path can

saturate and will limit the signal swing. This is not a desired

operation, as the supply current increases and the signal path

will be slow to recover from clipping. The absolute maximum

allowed differential input signal is limited by the long-term

reliability of the input stage. The limits in the Absolute

Maximum Ratings section should be observed in order to avoid

degrading device performance permanently.

R_F= 2.538 kꢀ for the AD8117 and 5.075 kꢀ for the AD8118.

In most cases, a single-ended input signal is referred to

midsupply, typically ground. In this case, the undriven

differential input can be connected to ground. For best dynamic

performance and lowest offset voltage, this unused input should

be terminated with an impedance matching the driven input,

instead of being directly shorted to ground. Due to the

differential feedback of the receiver, there is high frequency

signal current in the undriven input and it should

be treated as a signal line in the board design.

AD8117

IPn

INn

OPn

ONn

RCVR

AD8117

IPn

INn

OPn

ONn

75Ω

(OR 37.5Ω)

75Ω

RCVR

50Ω

Figure 67. Example of Input Driven Single-Ended

AC Coupling of Inputs

Figure 66. Example of Input Driven Differentially

It is possible to ac couple the inputs of the AD8117/AD8118

receiver. This is simplified because the bias current does not

need to be supplied externally. A capacitor in series with the

inputs to the AD8117/AD8118 creates a high-pass filter with

the input impedance of the device. This capacitor needs to be

sized such that the corner frequency is low enough for

frequencies of interest.

Single-Ended Input

The AD8117/AD8118 input receivers can be driven single-

endedly (unbalanced). From the standpoint of the receiver,

there is very little difference between signals applied positive

and negative in two phases to the input pair, vs. a signal applied

to one input only with the other input held at a constant

potential. One small difference is that the common mode

between the input pins is changing if only one input is moving,

and there is a very small common-mode to differential

conversion gain in the receiver that adds an additional gain

error to the output (see the common-mode rejection ratio for

the input stage in the Specifications section). For low

Differential Output

Benefits of Differential Operation

The AD8117/AD8118 have a fully differential switch core, with

differential outputs. The two output voltages move in opposite

polarity, with a differential feedback loop maintaining a fixed

output stage differential gain of +1 (the different overall signal

path gains between the AD8117 and AD8118 are set in the

input stage for best signal-to-noise ratio). This differential

output stage provides a benefit of crosstalk-canceling due to

parasitic coupling from one output to another, being equal and

out of phase. Additionally, if the output of the device is utilized

in a differential design, noise, crosstalk, and offset voltages

generated on-chip that are coupled equally into both outputs are

cancelled by the common-mode rejection ratio of the next

device in the signal chain. By utilizing the AD8117/AD8118

outputs in a differential application, the best possible noise and

offset specifications can be realized.

frequencies, this gain error is negligible. The common-mode

rejection ratio degrades with increasing frequency.

When operating the AD8117/AD8118 receivers single-endedly,

the observed input resistance at each input pin is lower than in

the differential input case, due to a fraction of the receiver

internal output voltage appearing as a common-mode signal on

its input terminals, bootstrapping the voltage on the input

resistance. This single-ended input resistance can be calculated

by the equation

Rev. A | Page 28 of 36

AD8117/AD8118

and termination of the output trace or cable. This is known as

back-termination, and helps shorten settling time by terminating

reflected signals when driving a load that is not accurately

terminated at the load end. A side effect of back-termination is

an attenuation of the output signal by a factor of two. In this

case, a gain of two is usually necessary somewhere in the signal

path to restore the signal.

Differential Gain

The specified signal path gain of the AD8117/AD8118 refers to

its differential gain. For the AD8117, the gain of +1 means that

the difference in voltage between the two output terminals is

equal to the difference applied between the two input terminals.

For the AD8118, the ratio of output difference voltage to

applied input difference voltage is +2.

The common mode, or average voltage of the pair of output

signals is set by the voltage on the VOCM pin. This voltage is

typically set to midsupply (often ground), but can be moved

approximately 0.5 V in order to accommodate cases where the

desired output common-mode voltage may not be midsupply

(as in the case of unequal split supplies). Adjusting VOCM can

limit differential swing internally below the specifications on

the data sheet.

AD8117/

AD8118

50Ω

OPn

ONn

+

100Ω

–

Figure 68. Example of Back-Terminated Differential Load

Regardless of the differential gain of the device, the common-

mode gain for the AD8117 and AD8118 is +1 to the output.

This means that the common mode of the output voltages

directly follows the reference voltage applied to the VOCM

input.

Single-Ended Output

Usage

The AD8117/AD8118 output pairs can be used single-endedly,

taking only one output and not using the second. This is often

desired to reduce the routing complexity in the design, or

because a single-ended load is being driven directly. This mode

of operation produces good results, but has some shortcomings

when compared to taking the output differentially. When

observing the single-ended output, noise that is common to

both outputs appears in the output signal. This includes thermal

noise in the chip biasing, as well as crosstalk that is coupled into

the signal path. This component noise and crosstalk is equal in

both outputs, and as such can be ignored by a differential

receiver with a high common-mode rejection ratio. However,

when taking the output single-ended, this noise is present with

respect to the ground (or VOCM) reference and is not rejected.

The VOCM reference is a high speed signal input, common to

all output stages on the device. It requires only small amounts of

bias current, but noise appearing on this pin is buffered to the

outputs of all the output stages. As such, the VOCM node should

be connected to a low noise, low impedance voltage to avoid

being a source of noise, offset, and crosstalk in the signal path.

Termination

The AD8117/AD8118 are designed to drive 150 ꢀ on each

output (or an effective 300 ꢀ differential), but the output stage

is capable of supplying the current to drive 100 ꢀ loads (200 ꢀ

differential) over the specified operating temperature range. If

care is taken to observe the maximum power derating curves,

the output stage can drive 75 ꢀ loads with slightly reduced slew

rate and bandwidth (an effective 150 ꢀ differential load).

When observing the output single-ended, the distribution of

offset voltages appears greater. In the differential case, the

difference between the outputs when the difference between the

inputs is zero is a small differential offset. This offset is created

from mismatches in components of the signal path, which must

be corrected by the finite differential loop gain of the device. In

the single-ended case, this differential offset is still observed,

but an additional offset component is also relevant. This

additional component is the common-mode offset, which is a

difference between the average of the outputs and the VOCM

reference. This offset is created by mismatches that affect the

signal path in a common-mode manner, and is corrected by the

finite common-mode loop gain of the device. A differential

receiver would reject this common-mode offset voltage, but in

the single-ended case, this offset is observed with respect to the

signal ground. The single-ended output sums half the

Termination at the load end is recommended for best signal

integrity. This load termination is often a resistor to a ground

reference on each individual output. By terminating to the

same voltage level that drives the VOCM reference, the power

dissipation due to dc termination current is reduced. In

differential signal paths, it is often desirable to terminate

differentially, with a single resistor across the differential

outputs at the load end. This is acceptable for the AD8117/

AD8118, but when the device outputs are placed in a disabled

state, a small amount of dc bias current is required if the output

is to present as a high impedance over an excursion of output

bus voltages. If the AD8117/AD8118 disabled outputs are

floated (or simply tied together by a resistor), internal nodes

saturate and an increase in disabled output current may

be observed.

differential offset voltage and all of the common-mode offset

voltage for a net increase in observed offset.

For best pulse response, it is often desirable to place a series

resistor in each output to match the characteristic impedance

Rev. A | Page 29 of 36

AD8117/AD8118

output draws current from the positive supply, the other output

draws current from the negative supply. When the phase

alternates, the first output draws current from the negative

supply and the second from the positive supply. The effect is

that a more constant current is drawn from each supply, such

that the crosstalk-inducing supply fluctuation is minimized.

Single-Ended Gain

The AD8117/AD8118 operate as a closed-loop differential

amplifier. The primary control loop forces the difference

between the output terminals to be a ratio of the difference

between the input terminals. One output increases in voltage,

while the other decreases an equal amount to make the total

difference correct. The average of these output voltages is forced

to be equal to the voltage on the VOCM terminal by a second

control loop. If only one output terminal is observed with

respect to the VOCM terminal, only half of the difference

voltage is observed. This implies that when using only one

output of the device, half of the differential gain is observed. An

AD8117 taken with single-ended output appears to have a gain

of +0.5. An AD8118 has a single-ended gain of +1.

A third benefit of driving balanced loads can be seen if one

considers that the output pulse response changes as load

changes. The differential signal control loop in the

AD8117/AD8118 forces the difference of the outputs to be a

fixed ratio to the difference of the inputs. If the two output

responses are different due to loading, this creates a difference

that the control loop sees as signal response error, and it will

attempt to correct this error. This distorts the output signal

from the ideal response if the two outputs were balanced.

This factor of one half in the gain increases the noise of the

device when referred to the input, contributing to higher noise

specifications for single-ended output designs.

AD8117/

AD8118

75Ω

OPn

ONn

Termination

75Ω

When operating the AD8117/AD8118 with a single-ended

output, the preferred output termination scheme is a resistor at

the load end to the VOCM voltage. A back-termination can be

used, at an additional cost of one half the signal gain.

150Ω

Figure 69. Example of Back-Terminated Single-Ended Load

In single-ended output operation, the complementary phase of

the output is not used, and may or may not be terminated

locally. Although the unused output can be floated to reduce

power dissipation, there are several reasons for terminating the

unused output with a load resistance matched to the load on the

signal output.

Decoupling

The signal path of the AD8117/AD8118 is based on high open-

loop gain amplifiers with negative feedback. Dominant-pole

compensation is used on-chip to stabilize these amplifiers over

the range of expected applied swing and load conditions. To

guarantee this designed stability, proper supply decoupling is

necessary with respect to both the differential control loops and

the common-mode control loops of the signal path. Signal-

generated currents must return to their sources through low

impedance paths at all frequencies in which there is still loop

gain (up to 700 MHz at a minimum). A wideband parallel

capacitor arrangement is necessary to properly decouple the

AD8117/AD8118.

One component of crosstalk is magnetic, coupling by mutual

inductance between output package traces and bond wires that

carry load current. In a differential design, there is coupling

from one pair of outputs to other adjacent pairs of outputs. The

differential nature of the output signal simultaneously drives the

coupling field in one direction for one phase of the output, and

in an opposite direction for the other phase of the output. These

magnetic fields do not couple exactly equal into adjacent output

pairs due to different proximities, but they do destructively

cancel the crosstalk to some extent. If the load current in each

output is equal, this cancellation is greater, and less adjacent

crosstalk is observed (regardless if the second output is actually

being used).

The signal path compensation capacitors in the AD8117/

AD8118 are connected to the VNEG supply. At high frequencies,

this limits the power supply rejection ratio (PSRR) from the

VNEG supply to a lower value than that from the VPOS supply.

If given a choice, an application board should be designed such

that the VNEG power is supplied from a low inductance plane,

subject to a least amount of noise.

A second benefit of balancing the output loads in a differential

pair is to reduce fluctuations in current requirements from the

power supply. In single-ended loads, the load currents alternate

from the positive supply to the negative supply. This creates a

parasitic signal voltage in the supply pins due to the finite

resistance and inductance of the supplies. This supply fluctuation

appears as crosstalk in all outputs, attenuated by the power

supply rejection ratio (PSRR) of the device. At low frequencies,

this is a negligible component of crosstalk, but PSRR falls off as

frequency increases. With differential, balanced loads, as one

The VOCM should be considered a reference pin and not a

power supply. It is an input to the high speed, high gain

common-mode control loop of all receivers and output drivers.

In the single-ended output sense, there is no rejection from

noise on the VOCM net to the output. For this reason, care

must be taken to produce a low noise VOCM source over the

entire range of frequencies of interest. This is not only

important to single-ended operation, but to differential

Rev. A | Page 30 of 36

AD8117/AD8118

V

POS

operation, as there is a common-mode to differential gain

conversion that becomes greater at higher frequencies.

I

OUTPUT, QUIESCENT

During operation of the AD8117/AD8118, transient currents

flow into the VOCM net from the amplifier control loops.

Although the magnitude of these currents are small (10 μA to

20 μA per output), they can contribute to crosstalk if they flow

through significant impedances. Driving VOCM with a low

impedance, low noise source is desirable.

QNPN

QPNP

V

OUTPUT

I

OUTPUT

I

OUTPUT, QUIESCENT

V

NEG

Power Dissipation

Figure 71. Simplified Output Stage

Calculation of Power Dissipation

8

Example

T

= 150°C

J

For the AD8117/AD8118, in an ambient temperature of 85°C,

with all 32 outputs driving 1 V rms into 100 ꢀ loads and power

supplies at 2.5 V, follow these steps:

7

6

5

4

1. Calculate power dissipation of AD8117/AD8118 using data

sheet quiescent currents. Disregard V_DDcurrent, as it is

insignificant.

P_D,QUIESCENT

=

(

V_POS× I_VPOS

)

+

(

V_NEG× I_VNEG

)

(

2.5 V× 500 mA

)

+

(

2.5 V× 500 mA = 2.5 W

)

2. Calculate power dissipation from loads. For a differential

output and ground-referenced load, the output power is

symmetrical in each output phase.

15

25

35

45

55

65

75

85

AMBIENT TEMPERATURE (°C)

Figure 70. Maximum Die Power Dissipation vs. Ambient Temperature

The curve in Figure 70 was calculated from

T_{JUNCTION, MAX}− T_AMBIENT

P_D,OUTPUT

=

(

V_POS− V_OUTPUT,RMS

)

× I_OUTPUT,RMS

= 15 mW

(2.5 V− 1V

)

×

(

1V/100 ꢀ

)

P_{D, MAX}

=

(1)

There are 32 output pairs, or 64 output currents.

θ_JA

nP_D,OUTPUT= 64 × 15mW = 0.96 W

As an example, if the AD8117/AD8118 is enclosed in an envi-

ronment at 45°C (T_A), the total on-chip dissipation under all

load and supply conditions must not be allowed to exceed 7.0 W.

3. Subtract the quiescent output stage current for number of

loads (64 in this example). The output stage is either

standing, or driving a load, but the current only needs to

be counted once (valid for output voltages > 0.5 V).

When calculating on-chip power dissipation, it is necessary to

include the rms current being delivered to the load, multiplied

by the rms voltage drop on the AD8117/AD8118 output

devices. For a sinusoidal output, the on-chip power dissipation

due to the load can be approximated by

P_DQ,OUTPUT

=

(

V_POS− V_NEG

)

× I_{OUTPUT,QUIESCENT}

× 1.65 mA = 8.25 mW

(

2.5 V− (−2.5 V)

)

There are 32 output pairs, or 64 output currents.

P_D,OUTPUT

=

(

V_POS− V_O

)

× I_{OUTPUT, RMS}

UTPUT, RMS

nP_DQ,OUTPUT= 64 × 8.25 mW = 0.53 W

For nonsinusoidal output, the power dissipation should be

calculated by integrating the on-chip voltage drop multiplied by

the load current over one period.

4. Verify that the power dissipation does not exceed

maximum allowed value.

P_{D,ON −CHIP}= P_D,QUIESCENT+ nP_D,OUTPUT− nP_DQ,OUTPUT

P_D,ON−CHIP= 2.5 W+ 0.96 W− 0.53 W = 2.9 W

The user can subtract the quiescent current for the Class AB

output stage when calculating the loaded power dissipation. For

each output stage driving a load, subtract a quiescent power

according to

From Figure 70 or Equation 1, this power dissipation is below

the maximum allowed dissipation for all ambient temperatures

up to and including 85°C.

P_DQ,OUTPUT

=

(

V_POS− V_NEG× I_{OUTPUT,QUIESCENT}

)

where I_{OUTPUT, QUIESCENT}= 1.65 mA for each single-ended output pin.

For each disabled output, the quiescent power supply current in

VPOS and VNEG drops by approximately 9 mA.

Rev. A | Page 31 of 36

AD8117/AD8118

are common mode to the signal and can be rejected by a

differential receiver.

Short-Circuit Output Conditions

Although there is short-circuit current protection on the

AD8117/AD8118 outputs, the output current can reach values

of 80 mA into a grounded output. Any sustained operation with

too many shorted outputs can exceed the maximum die

temperature and can result in device failure (see the Absolute

Maximum Ratings section).

Areas of Crosstalk

A practical AD8117/AD8118 circuit must be mounted to some

sort of circuit board in order to connect it to power supplies and

measurement equipment. Great care has been taken to create an

evaluation board that adds minimum crosstalk to the intrinsic

device. This, however, raises the issue that a system’s crosstalk is

a combination of the intrinsic crosstalk of the devices in

addition to the circuit board to which they are mounted. It is

important to try to separate these two areas when attempting to

minimize the effect of crosstalk.

Crosstalk

Many systems, such as broadcast video and KVM switches, that

handle numerous analog signal channels, have strict require-

ments for keeping the various signals from influencing any of

the others in the system. Crosstalk is the term used to describe

the coupling of the signals of other nearby channels to a given

channel.

In addition, crosstalk can occur among the inputs to a

crosspoint and among the outputs. It can also occur from input

to output. Techniques are discussed in the following sections for

diagnosing which part of a system is contributing to crosstalk.

When there are many signals in close proximity in a system, as

is undoubtedly the case in a system that uses the AD8117/AD8118,

the crosstalk issues can be quite complex. A good understanding

of the nature of crosstalk and some definition of terms is

required in order to specify a system that uses one or more

crosspoint devices.

Measuring Crosstalk

Crosstalk is measured by applying a signal to one or more

channels and measuring the relative strength of that signal on a

desired selected channel. The measurement is usually expressed

as dB down from the magnitude of the test signal. The crosstalk

is expressed by

Types of Crosstalk

Crosstalk can be propagated by means of any of three methods.

These fall into the categories of electric field, magnetic field,

and sharing of common impedances. This section explains

these effects.

⎛

⎜

⎞

⎟

A

_SEL(s)

XT = 20 log₁₀

⎜

⎝

⎟

⎠

A_TEST(s)

where:

s = jω, the Laplace transform variable.

_SEL(s) is the amplitude of the crosstalk induced signal in the

selected channel.

_TEST(s) is the amplitude of the test signal.

Every conductor can be both a radiator of electric fields and a

receiver of electric fields. The electric field crosstalk mechanism

occurs when the electric field created by the transmitter

propagates across a stray capacitance (for example free space),

couples with the receiver, and induces a voltage. This voltage is

an unwanted crosstalk signal in any channel that receives it.

A

It can be seen that crosstalk is a function of frequency, but not a

function of the magnitude of the test signal (to first order). In

addition, the crosstalk signal will have a phase relative to the

test signal associated with it.

Currents flowing in conductors create magnetic fields that

circulate around the currents. These magnetic fields then

generate voltages in any other conductors whose paths they

link. The undesired induced voltages in these other channels

are crosstalk signals. The channels that crosstalk can be said to

have a mutual inductance that couples signals from one channel

to another.

A network analyzer is most commonly used to measure

crosstalk over a frequency range of interest. It can provide both

magnitude and phase information about the crosstalk signal.

As a crosspoint system or device grows larger, the number of

theoretical crosstalk combinations and permutations can

become extremely large. For example, in the case of the 32 × 32

matrix of the AD8117/AD8118, look at the number of crosstalk

terms that can be considered for a single channel, for example,

the input IN00. IN00 is programmed to connect to one of the

AD8117/AD8118 outputs where the measurement can be made.

The power supplies, grounds, and other signal return paths of a

multichannel system are generally shared by the various

channels. When a current from one channel flows in one of

these paths, a voltage that is developed across the impedance

becomes an input crosstalk signal for other channels that share

the common impedance.

All these sources of crosstalk are vector quantities; therefore, the

magnitudes cannot simply be added together to obtain the total

crosstalk. In fact, there are conditions where driving additional

circuits in parallel in a given configuration can actually reduce

the crosstalk. Because the AD8117/AD8118 are fully differential

designs, many sources of crosstalk either destructively cancel, or

First, the crosstalk terms associated with driving a test signal

into each of the other 31 inputs can be measured one at a time,

while applying no signal to IN00. Then the crosstalk terms

associated with driving a parallel test signal into all 31 other

inputs can be measured two at a time in all possible

combinations, then three at a time, and so on, until, finally,

Rev. A | Page 32 of 36

AD8117/AD8118

there is only one way to drive a test signal into all 31 other

inputs in parallel.

All the other inputs are driven in parallel with the same test

signal (practically provided by a distribution amplifier), with all

other outputs except OUT07 disabled. Since grounded IN07

is programmed to drive OUT07, no signal should be present.

Any signal that is present can be attributed to the other 15

hostile input signals, because no other outputs are driven

(they are all disabled). Thus, this method measures the all

hostile input contribution to crosstalk into IN07. Of course, the

method can be used for other input channels and combinations

of hostile inputs.

Each of these cases is legitimately different from the others and

might yield a unique value, depending on the resolution of the

measurement system, but it is hardly practical to measure all

these terms and then specify them. In addition, this describes

the crosstalk matrix for just one input channel. A similar

crosstalk matrix can be proposed for every other input. In

addition, if the possible combinations and permutations for

connecting inputs to the other outputs (not used for measure-

ment) are taken into consideration, the numbers rather quickly

grow to astronomical proportions. If a larger crosspoint array of

multiple AD8117/AD8118s is constructed, the numbers grow

larger still.

For output crosstalk measurement, a single input channel is

driven (IN00, for example) and all outputs other than a given

output (IN07 in the middle) are programmed to connect to

IN00. OUT07 is programmed to connect to IN15 (far away

from IN00), which is terminated to ground. Thus OUT07

should not have a signal present since it is listening to a quiet

input. Any signal measured at the OUT07 can be attributed to

the output crosstalk of the other 16 hostile outputs. Again, this

method can be modified to measure other channels and other

crosspoint matrix combinations.

Obviously, some subset of all these cases must be selected to be

used as a guide for a practical measure of crosstalk. One

common method is to measure all hostile crosstalk; this means

that the crosstalk to the selected channel is measured while all

other system channels are driven in parallel. In general, this

yields the worst crosstalk number, but this is not always the

case, due to the vector nature of the crosstalk signal.

Effect of Impedances on Crosstalk

Other useful crosstalk measurements are those created by one

nearest neighbor or by the two nearest neighbors on either side.

These crosstalk measurements are generally higher than those

of more distant channels, so they can serve as a worst-case

measure for any other one-channel or two-channel crosstalk

measurements.

The input side crosstalk can be influenced by the output

impedance of the sources that drive the inputs. The lower the

impedance of the drive source, the lower the magnitude of the

crosstalk. The dominant crosstalk mechanism on the input side

is capacitive coupling. The high impedance inputs do not have

significant current flow to create magnetically induced crosstalk.

However, significant current can flow through the input termi-

nation resistors and the loops that drive them. Thus, the PC

board on the input side can contribute to magnetically coupled

crosstalk.

Input and Output Crosstalk

Capacitive coupling is voltage-driven (dV/dt), but is generally a

constant ratio. Capacitive crosstalk is proportional to input or

output voltage, but this ratio is not reduced by simply reducing

signal swings. Attenuation factors must be changed by changing

impedances (lowering mutual capacitance), or destructive

canceling must be utilized by summing equal and out of phase

components. For high input impedance devices such as the

AD8117/AD8118, capacitances generally dominate input-

generated crosstalk.

From a circuit standpoint, the input crosstalk mechanism looks

like a capacitor coupling to a resistive load. For low frequencies,

the magnitude of the crosstalk is given by

XT = 20 log₁₀

where:

R_Sis the source resistance.

[

(R_SC_M) × s

]

Inductive coupling is proportional to current (dI/dt), and often

scales as a constant ratio with signal voltage, but also shows a

dependence on impedances (load current). Inductive coupling

can also be reduced by constructive canceling of equal and out

of phase fields. In the case of driving low impedance video

loads, output inductances contribute highly to output crosstalk.

C_Mis the mutual capacitance between the test signal circuit and

the selected circuit.

s is the Laplace transform variable.

From the preceding equation, it can be observed that this

crosstalk mechanism has a high-pass nature; it can also be

minimized by reducing the coupling capacitance of the input

circuits and lowering the output impedance of the drivers. If the

input is driven from a 75 ꢀ terminated cable, the input crosstalk

can be reduced by buffering this signal with a low output

impedance buffer.

The flexible programming capability of the AD8117/AD8118

can be used to diagnose whether crosstalk is occurring more on

the input side or the output side. Some examples are illustrative.

A given input pair (IN07 in the middle for this example) can be

programmed to drive OUT07 (also in the middle). The inputs

to IN07 are just terminated to ground (via 50 ꢀ or 75 ꢀ) and no

signal is applied.

Rev. A | Page 33 of 36

AD8117/AD8118

On the output side, the crosstalk can be reduced by driving a

lighter load. Although the AD8117/AD8118 are specified with

excellent differential gain and phase when driving a standard

150 ꢀ video load, the crosstalk will be higher than the

minimum obtainable due to the high output currents. These

currents will induce crosstalk via the mutual inductance of the

output pins and bond wires of the AD8117/AD8118.

applications are generally 50 ꢀ single-ended (and board

manufacturers have the most experience with this application).

CAT-5 cabling is usually driven as differential pairs of 100 ꢀ

differential impedance.

For flexibility, the AD8117/AD8118 do not contain on-chip

termination resistors. This flexibility in application comes with

some board layout challenges. The distance between the termi-

nation of the input transmission line and the AD8117/AD8118

die is a high impedance stub, and causes reflections of the input

signal. With some simplification, it can be shown that these

reflections cause peaking of the input at regular intervals in

frequency, dependent on the propagation speed (V_P) of the

signal in the chosen board material and the distance (d)

between the termination resistor and the AD8117/AD8118. If

the distance is great enough, these peaks can occur in-band. In

fact, practical experience shows that these peaks are not high-Q,

and should be pushed out to three or four times the desired

bandwidth in order to not have an effect on the signal. For a

board designer using FR4 (V_P= 144 × 106 m/s), this means the

AD8117/AD8118 input should be placed no farther than 1.5 cm

after the termination resistors, and preferably should be placed

even closer. The BGA substrate routing inside the AD8117/

AD8118 is approximately 1 cm in length and adds to the stub

length, so 1.5 cm PCB routing equates to d = 2.5 × 10⁻²m in the

calculations.

From a circuit standpoint, this output crosstalk mechanism

looks like a transformer with a mutual inductance between the

windings that drive a load resistor. For low frequencies, the

magnitude of the crosstalk is given by

⎛

⎜

⎝

⎞

⎟

⎠

s

⎜

XT = 20 log₁₀M_XY

×

R_L

where:

_XYis the mutual inductance of Output X to Output Y.

M

R_Lis the load resistance on the measured output.

This crosstalk mechanism can be minimized by keeping the

mutual inductance low and increasing R_L. The mutual

inductance can be kept low by increasing the spacing of the

conductors and minimizing their parallel length.

PCB Layout

Extreme care must be exercised to minimize additional

crosstalk generated by the system circuit board(s). The areas

that must be carefully detailed are grounding, shielding, signal

routing, and supply bypassing.

(

2n + 1 × V_P

)

f_PEAK

=

4d

The packaging of the AD8117/AD8118 is designed to help keep

the crosstalk to a minimum. On the BGA substrate, each pair is

carefully routed to predominately couple to each other, with

shielding traces separating adjacent signal pairs. The ball grid

array is arranged such that similar board routing can be achieved.

Only the outer two rows are used for signals, such that vias can

be used to take the input rows to a lower signal plane if desired.

where n = {0, 1, 2, 3, …}.

In some cases, it is difficult to place the termination close to the

AD8117/AD8118 due to space constraints, differential routing,

and large resistor footprints. A preferable solution in this case is

to maintain a controlled transmission line past the AD8117/

AD8118 inputs and terminate the end of the line. This is known

as fly-by termination. The input impedance of the AD8117/

AD8118 is large enough and stub length inside the package is

small enough that this works well in practice. Implementation

of fly-by input termination often includes bringing the signal in

on one routing layer, then passing through a filled via under the

AD8117/AD8118 input ball, then back out to termination on

another signal layer. In this case, care must be taken to tie the

reference ground planes together near the signal via if the signal

layers are referenced to different ground planes.

The input and output signals have minimum crosstalk if they

are located between ground planes on layers above and below,

and separated by ground in between. Vias should be located as

close to the IC as possible to carry the inputs and outputs to the

inner layer. The input and output signals surface at the input

termination resistors and the output series back-termination

resistors. To the extent possible, these signals should also be

separated as soon as they emerge from the IC package.

PCB Termination Layout

AD8117/

AD8118

As frequencies of operation increase, the importance of proper

transmission line signal routing becomes more important. The

bandwidth of the AD8117/AD8118 is large enough that using

high impedance routing does not provide a flat in-band

frequency response for practical signal trace lengths. It is

necessary for the user to choose a characteristic impedance

suitable for the application and properly terminate the input

and output signals of the AD8117/AD8118. Traditionally, video

applications have used 75 ꢀ single-ended environments. RF

OPn

ONn

IPn

INn

75Ω

Figure 72. Fly-By Input Termination, Grounds for the Two Transmission Lines

Shown Must be Tied Together Close to the INn Pin.

Rev. A | Page 34 of 36

AD8117/AD8118

If multiple AD8117/AD8118s are to be driven in parallel, a fly-

by input termination scheme is very useful, but the distance

from each AD8117/AD8118 input to the driven input

transmission line is a stub that should be minimized in length

and parasitics using the discussed guidelines.

as trace widths become large. In most cases, the best practical

solution is to place the half-characteristic impedance resistor as

close as possible (preferably less than 1.5 cm away) and to

reduce the parasitics of the stub (by removing the ground plane

under the stub, for example). In either case, the designer must

decide if the layout complexity created by a balanced,

terminated solution is preferable to simply grounding the

undriven input at the ball with no trace.

When driving the AD8117/AD8118 single-endedly, the

undriven input is often terminated with a resistance in order to

balance the input stage. It can be seen that by terminating the

undriven input with a resistor of one half the characteristic

impedance, the input stage is perfectly balanced (37.5 ꢀ, for

example, to balance the two parallel 75 ꢀ terminations on the

driven input). However, due to the feedback in the input

receiver, there is high speed signal current leaving the undriven

input. In order to terminate this high speed signal, proper

transmission line techniques should be used. One solution is to

adjust the trace width to create a transmission line of half the

characteristic impedance and terminate the far end with this

resistance (37.5 ꢀ in a 75 ꢀ system). This is not often practical

Although the examples discussed so far are for input

termination, the theory is similar for output back-termination.

Taking the AD8117/AD8118 as an ideal voltage source, any

distance of routing between the AD8117/AD8118 and a back-

termination resistor will be an impedance mismatch that

potentially creates reflections. For this reason, back-termination

resistors should also be placed close to the AD8117/AD8118. In

practice, because back-termination resistors are series elements,

they can be placed close to the AD8117/AD8118 outputs.

VPOS

VDD

J3

PC_VDD

PLD_VDD

VDD

VPOS

ANALOG

SMA

50Ω

IN[31:0],

IP[31:0]

ON[31:0],

OP[31:0]

IN[31:0], IP[31:0]

ON[31:0], OP[31:0]

50Ω

AD8117/

AD8118

CLK

RESET

WE

UPDATE

DATA IN

DATA OUT

VOCM

PC

PARALLEL

PORT

LOGIC

ISOLATORS

CPLD

LOGIC

DGND

VNEG

J8,

W3 TO W7

PC_GND

VNEG

GND

Figure 73. Evaluation Board Simplified Schematic

Rev. A | Page 35 of 36

AD8117/AD8118

OUTLINE DIMENSIONS

A1 CORNER

INDEX AREA

31.00

BSC SQ

6

4

2

22 20 18 16 14 12 10

23 21 19 17 15 13 11

8

9

7

5

3

1

A

B

C

D

E

F

BALL A1

INDICATOR

G

H

J

K

L

27.94

TOP VIEW

BOTTOM

VIEW

BSC SQ

M

N

P

R

T

U

V

W

1.27

BSC

Y

AA

AB

AC

DETAIL A

1.07

0.99

0.92

DETAIL A

*

1.765 MAX

0.10 MIN

0.70

0.63

0.56

0.90

0.75

0.60

COPLANARITY

0.20

0.25 MIN

(4

SEATING

PLANE

BALL DIAMETER

)

*

COMPLIANT TO JEDEC STANDARDS MO-192-BAN-2

WITH THE EXCEPTION TO PACKAGE HEIGHT.

Figure 74. 304-Ball Ball Grid Array, Thermally Enhanced [BGA_ED]

(BP-304)

Dimensions shown in millimeters

ORDERING GUIDE

Temperature

Range

Model

Package Description

Package Option

BP-304

AD8117ABPZ¹

AD8118ABPZ¹

AD8117-EVAL

AD8118-EVAL

−40°C to +85°C

304-Ball Ball Grid Array Package, Thermally Enhanced [BGA_ED]

Evaluation Board

¹Z = RoHS Compliant Part.

registered trademarks are the property of their respective owners.

D06365-0-5/07(A)

Rev. A | Page 36 of 36


型号：	AD8118
厂家：	ADI
描述：	600 MHz, 32 】 32 Buffered Analog Crosspoint Switch 600兆赫， 32 】 32缓冲模拟交叉点开关开关
文件：	总36页 (文件大小：877K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

AD8118 [ADI]

相关型号：

AD8118-EVAL

AD8118ABPZ

AD8118_15

AD811ACHIPS

AD811AN

AD811AN

AD811ANZ

AD811ANZ

AD811AR-16

AD811AR-16

AD811AR-16-REEL

AD811AR-16-REEL7