AD8203YR [ADI]
IC IC,DIFFERENTIAL AMPLIFIER,SINGLE,SOP,8PIN,PLASTIC, Operational Amplifier;型号: | AD8203YR |
厂家: | ADI |
描述: | IC IC,DIFFERENTIAL AMPLIFIER,SINGLE,SOP,8PIN,PLASTIC, Operational Amplifier 放大器 光电二极管 |
文件: | 总13页 (文件大小:505K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
High Common-Mode Voltage,
Single-Supply
Difference Amplifier
Preliminary Technical Data
AD8203
FEATURES
FUNCTIONAL BLOCK DIAGRAM
+V
6
NC
7
A1
3
A2
4
High common-mode voltage range −12 V to +30 V at
a 5 V supply voltage
S
AD8203
Operating temperature range
−40°C to +150°C
Supply voltage range: 3.5 V to 12 V
Low-pass filter (one pole or two pole)
100kΩ
G = ×10
+IN
A1
–IN
G = ×2
+IN
A2
–IN
8
1
+IN
–IN
5
OUT
10kΩ
10kΩ
EXCELLENT AC AND DC PERFORMANCE
200kΩ
200kΩ
±1 mV voltage offset
±1 ppm/°C typ gain drift
77 dB CMRR min dc to 10 kHz
2
NC = NO CONNECT
GND
PLATFORMS
Figure 1. SOIC (R) Package Die Form
Transmission control
Diesel injection control
Engine management
Adaptive suspension control
Vehicle dynamics control
INDUCTIVE
LOAD
5V
CLAMP
DIODE
OUTPUT
GENERAL DESCRIPTION
+IN
NC +V
OUT
S
The AD8203 is a single-supply difference amplifier for
amplifying and low-pass filtering small differential voltages in
the presence of a large common-mode voltage. The input CMV
range extends from −12 V to +30 V at a typical supply voltage of
5 V.
BATTERY
14V
4 TERM
SHUNT
AD8203
–IN GND A1
A2
POWER
DEVICE
The AD8203 is offered in die and packaged form. Both
package options are specified over wide temperature ranges,
making the AD8203 well suited for use in many automotive
platforms. The AD8203 is specified over a temperature range
of −40°C to +150°C.
COMMON
NC = NO CONNECT
Figure 2.High Line Current Sensor
POWER
DEVICE
5V
Automotive platforms demand precision components for better
system control. The AD8203 provides excellent ac and dc
performance that keeps errors to a minimum in the user’s
system. Typical offset and gain drift in the SOIC package are
5 µV/°C and 1 ppm/°C, respectively. The device also delivers a
minimum CMRR of 77 dB from dc to 10 kHz.
OUTPUT
+IN
NC +V
OUT
S
BATTERY
14V
4 TERM
SHUNT
AD8203
–IN GND A1
A2
The AD8203 features an externally accessible 100 kΩ resistor
at the output of the preamp A1, which can be used for low-pass
filter applications and for establishing gains other than 20.
CLAMP
DIODE
INDUCTIVE
LOAD
COMMON
NC = NO CONNECT
Rev. PrA
Figure 3. Low Line Current Sensor
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its use,
nor for any infringements of patents or other rights of third parties that may
result from its use. Specifications subject to change without notice. No license
is granted by implication or otherwise under any patent or patent rights of
Analog Devices. Trademarks and registered trademarks are the property of
their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106,
U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.326.8703 © 2004 Analog Devices, Inc. All rights reserved.
AD8203
Preliminary Technical Data
TABLE OF CONTENTS
Specifications—Single Suppy...................................................3
Absolute Maximum Ratings......................................................5
Pin Configurations And Function Descriptions.........................6
ESD Caution..........................................................................6
Typical Performance Characteristics.........................................7
Theory of Operation..................................................................9
Applications ............................................................................10
Current Sensing ...................................................................10
Gain Adjustment..................................................................10
Gain Trim ............................................................................11
Low-Pass Filtering ..............................................................11
High-Line Current Sensing with LPF and Gain Adjustment
.............................................................................................12
Driving Charge Redistribution ADCs..................................12
Outline Dimensions ................................................................13
Ordering Guide....................................................................13
REVISION HISTORY
Rev. PrA | Page 2 of 13
Preliminary Technical Data
AD8203
SPECIFICATIONS—SINGLE SUPPY
TA = +25°C, VS = 5 V, VCM = 0 V, RL = 10 kΩ.
Table 1.
AD8203 SOIC
AD8203 DIE
Parameter
Condition
Min Typ Max
Min Typ Max
Unit
SYSTEM GAIN
Initial
14
14
+1
V/V
Error
4.8 ≤Vout ≥ 0.01 Vdc
−0.3
+0.3 −1
%
Vs. Temperature
VOLTAGE OFFSET
Input Offset (RTI)
Vs. Temperature
1
20
25
30
ppm/°C
VCM = 0.01 V; 25°C
-40C -> 125C
−1
+1
10
15
−1
+1
mV
-10
-15
0.3
5
µV/°C
µV/°C
-40C -> 150C
INPUT
Input Impedance
Differential
260
135
−12
325
170
390
205
+30
320 400
160 200
−2
480
240
+24
kΩ
kΩ
V
Common-Mode
CMV
Continuous
VCM = 0V to 10 V
f = DC
Common Mode Rejection1
82
82
77
f = 1 kHz
f = 10 kHz2
80
80
dB
dB
PREAMPLIFIER
Gain
7
7
V/V
%
V
Gain Error
−0.3
0.01
97
+0.3 −1
+1
4.8
103
Output Voltage Range
Output Resistance
Slew Rate
4.8
0.02
97
100
103
100
kΩ
TBD
TBD
OUTPUT BUFFER
Gain
2
2
2
V/V
%
Gain Error
−0.3
+0.3 −1
4.8 0.02
+1
Output Voltage Range
Input Bias Current
Output Resistance
DYNAMIC RESPONSE
System Bandwidth
0.01
4.8
V
40
2
Ω
Vin =0.01Vdc, Vout = 1Vpp
Vin =0.01Vdc, Vout =4v step
30
50
30
45
kHz
Slew Rate
0.28
0.22
V/µs
NOISE
0.1 Hz to 10 Hz
Spectral Density, 1 kHz, RTI
POWER SUPPLY
Operating Range
10
10
µV p-p
275
300
nV/√Hz
3.5
12
4.7
75
12
1
V
Quiescent Current vs.
Temperature
PSRR
VO = 0.1 V dc
0.25 1.0
0.25
80
mA
VS = 3.5V to 12 V
75
83
dB
TEMPERATURE RANGE
For Specified Performance
−40
+150 −40
+150 °C
1 Source imbalance < 2 Ω.
Rev. PrA | Page 3 of 13
AD8203
Preliminary Technical Data
2 The AD8202 preamplifier exceeds 77 dB CMRR at 10 kHz. However, since the signal is available only by way of a 100 kΩ resistor, even the small amount
of pin-to-pin capacitance between Pins 1, 8 and 3, 4 may couple an input common-mode signal larger than the greatly attenuated preamplifier output. The
effect of pin-to-pin coupling may be neglected in all applications using filter capacitors at Node 3.
Rev. PrA | Page 4 of 13
Preliminary Technical Data
AD8203
ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter
Rating
12.5 V
44 V
Supply Voltage
Transient Input Voltage (300 ms)
Continuous Input Voltage
Reversed Supply Voltage Protection
Operating Temperature Range
DIE
35 V
0.3 V
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only and functional operation of the device at these or
any other condition s above those indicated in the operational
section of this specification is not implied. Exposure to
absolute maximum rating conditions for extended periods may
affect device reliability.
−40°C to +150°C
−40°C to +150°C
−65°C to +150°C
Indefinate
SOIC
Storage Temperature
Output Short-Circuit Duration
Lead Temperature Range
(Soldering 10 sec)
300°C
Rev. PrA | Page 5 of 13
AD8203
Preliminary Technical Data
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
–IN
GND
A1
1
2
3
4
8
7
6
5
+IN
NC
+V
AD8203
+V
S
TOP VIEW
(Not to Scale)
S
A2
OUT
NC = NO CONNECT
Figure 4. 8-Lead SOIC
OUT
+IN
Table 3. 8-Lead SOIC Pin Function Descriptions
Pin No.
Mnemonic
1
2
3
4
5
6
7
8
−IN
GND
A1
A2
–IN
OUT
+VS
NC
A2
+IN
GND
A1
Figure 5. Metallization Photograph
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although this
product features proprietary ESD protection circuitry, permanent damage may occur on devices
subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended
to avoid performance degradation or loss of functionality.
Rev. PrA | Page 6 of 13
Preliminary Technical Data
AD8203
TYPICAL PERFORMANCE CHARACTERISTICS
TA = 25°C, VS = 5 V, VCM = 0 V, RL = 10 kΩ, unless otherwise noted.
30
25
20
15
10
5
30
25
20
15
10
5
0
–2
–4
–6
–8
–10
–12
+V
CM
0
–V
CM
–5
–10
–15
–20
0
1k
10k
FREQUENCY (Hz)
100k
1M
2
3
4
5
SUPPLY VOLTAGE (V)
Figure 6. Input Common-Mode Range vs. Supply
Figure 9. Gain vs. Frequency
0
100
95
90
85
80
75
70
65
60
55
50
–5
R
= ∞
L
–10
–15
–20
–25
R
= 10kΩ TO GND
L
–30
–35
2
3
4
5
10
100
1k
10k
100k
1M
SUPPLY VOLTAGE (V)
FREQUENCY (Hz)
Figure 7.Output Voltage, VS vs. Supply
Figure 10. Common-Mode Rejection Ratio vs. Frequency
5
4
3
2
1
0
100
90
80
70
60
50
40
30
20
10
0
10
100
1k
10k
10
100
1k
10k
100k
LOAD RESISTANCE (Ω)
FREQUENCY (Hz)
Figure 11. Power Supply Rejection Ratio vs. Frequency
Figure 8. Output Voltage Swing vs. Load Resistance
Rev.PrA | Page 7 of 13
AD8203
Preliminary Technical Data
TEK RUN: 2.5MS/s AVERAGE
TEK RUN: 2.5MS/s HI RES
V
, R = 10kΩ
OUT
L
V
, R = 10kΩ
L
OUT
1
1
2
T
MAGNIFIED V
IN
OUT
V
3
2
V
IN
CH1 1V
CH3 100mV
CH 2 10mV M 20µs CH1 1.36V
CH1 500mVΩ CH2 50mVΩ M 20µs CH1 1.5V
Figure 12. Pulse Response
Figure 13. Settling Time
Rev. PrA | Page 8 of 13
Preliminary Technical Data
THEORY OF OPERATION
AD8203
The AD8203 consists of a preamp and buffer arranged as
shown in Figure 14. Like-named resistors have equal values.
To minimize these errors while extending the common-mode
range, a dedicated feedback loop is employed to reduce the
range of common-mode voltage applied to A1 for a given
overall range at the inputs. By offsetting the range of voltage
applied to the compensator, the input common-mode range is
also offset to include voltages more negative than the power
supply. Amplifier A3 detects the common-mode signal applied
to A1 and adjusts the voltage on the matched RCM resistors to
reduce the common-mode voltage range at the A1 inputs. By
adjusting the common voltage of these resistors, the common-
mode input range is extended while, at the same time, the
normal mode signal attenuation is reduced, leading to better
performance referred to input.
The preamp incorporates a dynamic bridge (subtractor) circuit.
Identical networks (within the shaded areas), consisting of RA,
RB, RC, and RG, attenuate input signals applied to Pins 1 and 8.
Note that when equal amplitude signals are asserted at inputs 1
and 8, and the output of A1 is equal to the common potential
(i.e., zero), the two attenuators form a balanced-bridge network.
When the bridge is balanced, the differential input voltage at
A1, and thus its output, will be zero.
Any common-mode voltage applied to both inputs will keep the
bridge balanced and the A1 output at zero. Because the resistor
networks are carefully matched, the common-mode signal
rejection approaches this ideal state.
The output of the dynamic bridge taken from A1 is connected
to Pin 3 by way of a 100 kΩ series resistor, provided for low-
pass filtering and gain adjustment. The resistors in the input
networks of the preamp and the buffer feedback resistors are
ratio trimmed for high accuracy.
However, if the signals applied to the inputs differ, the result is
a difference at the input to A1. A1 responds by adjusting its
output to drive RB, by way of RG, to adjust the voltage at its
inverting input until it matches the voltage at its noninverting
input.
The output of the preamp drives a gain-of-2 buffer amplifier,
A2, implemented with carefully matched feedback resistors RF.
By attenuating voltages at Pins 1 and 8, the amplifier inputs are
held within the power supply range, even if Pin 1 and Pin 8
input levels exceed the supply, or fall below common (ground.)
The input network also attenuates normal (differential) mode
voltages. RC and RG form an attenuator that scales A1 feedback,
forcing large output signals to balance relatively small
differential inputs. The resistor ratios establish the preamp gain
at 10.
The 2-stage system architecture of the AD8203 enables the user
to incorporate a low-pass filter prior to the output buffer. By
separating the gain into two stages, a full-scale, rail-to-rail
signal from the preamp can be filtered at Pin 3, and a half-scale
signal, resulting from filtering, can be restored to full scale by
the output buffer amp. The source resistance seen by the
inverting input of A2 is approximately 100 kΩ to minimize the
effects of A2’s input bias current. However, this current is quite
small and errors resulting from applications that mismatch the
resistance are correspondingly small.
Because the differential input signal is attenuated and then
amplified to yield an overall gain of 10, the amplifier A1
operates at a higher noise gain, multiplying deficiencies such as
input offset voltage and noise with respect to Pins 1 and 8.
+IN
8
–IN
1
R
R
A
A
100kΩ
3
4
A1
5
(TRIMMED)
A2
R
R
R
R
F
F
CM
CM
A3
R
R
R
B
B
C
AD8203
R
R
R
G
G
C
2
COM
Figure 14. Simplified Schematic
Rev. PrA | Page 9 of 13
AD8203
Preliminary Technical Data
APPLICATIONS
S
The AD8203 difference amplifier is intended for applications
where it is required to extract a small differential signal in the
presence of large common-mode voltages. The input resistance
is nominally 200 kΩ, and the device can tolerate common-
mode voltages higher than the supply voltage and lower than
ground.
+V
OUT
S
+IN
NC
+V
OUT
VDIFF
2
Ω
10k
10k
20R
EXT
Ω
GAIN =
R
Ω
+ 100k
EXT
AD8203
DIFF
V
2
GAIN
100k
R
Ω
= 100k
V
Ω
EXT
The open collector output stage will source current to within
20 mV of ground.
CM
–
20 GAIN
–IN
GND
A1
A2
CURRENT SENSING
High-Line, High Current Sensing
R
EXT
Basic automotive applications making use of the large
common-mode range are shown in Figure 2 and Figure 3. The
capability of the device to operate as an amplifier in primary
battery supply circuits is shown in Figure 2; Figure 3 illustrates
the ability of the device to withstand voltages below system
ground.
NC = NO CONNECT
02054-B-016
Figure 16. Adjusting for Gains Less than 20
The overall bandwidth is unaffected by changes in gain using
this method, although there may be a small offset voltage due
Low Current Sensing
to the imbalance in source resistances at the input to the buffer.
In many cases, this can be ignored, but if desired, it can be
nulled by inserting a resistor equal to 100 kΩ minus the parallel
sum of REXT and 100 kΩ, in series with Pin 4. For example,
with REXT = 100 kΩ (yielding a composite gain of ×10), the
optional offset nulling resistor is 50 kΩ.
The AD8203 can also be used in low current sensing
applications, such as the 4 to 20 mA current loop shown in
Figure 15. In such applications, the relatively large shunt
resistor can degrade the common-mode rejection. Adding a
resistor of equal value in the low impedance side of the input
corrects for this error.
Gains Greater than 20
10Ω
1%
Connecting a resistor from the output of the buffer amplifier to
its noninverting input, as shown in Figure 17, will increase the
5V
OUTPUT
+IN
NC
+VS OUT
gain. The gain is now multiplied by the factor REXT/(REXT
−
100 kΩ); for example, it is doubled for REXT = 200 kΩ. Overall
gains as high as 50 are achievable in this way. Note that the
accuracy of the gain becomes critically dependent on the
resistor value at high gains. Also, the effective input offset
voltage at Pins 1 and 8 (about six times the actual offset of A1)
limits the part’s use in high gain, dc-coupled applications.
+
10Ω
1%
AD8203
–IN GND A1
A2
+V
S
OUT
NC = NO CONNECT
+IN
NC
+V
S
OUT
V
DIFF
10k
Ω
10k
Ω
20R
EXT
Figure 15. 4 to 20 mA Current Loop Receiver
GAIN =
2
R
100k
EXT
–
Ω
AD8203
R
EXT
GAIN ADJUSTMENT
V
GAIN
20
DIFF
R
= 100k
100k
EXT
Ω
Ω
V
CM
2
GAIN
–
The default gain of the preamplifier and buffer are ×10 and ×2,
respectively, resulting in a composite gain of ×20. With the
addition of external resistor(s) or trimmer(s), the gain may be
lowered, raised, or finely calibrated.
–IN
GND A1
A2
NC = NO CONNECT
02054-B-017
Gains Less than 20
Since the preamplifier has an output resistance of 100 kΩ, an
external resistor connected from Pins 3 and 4 to GND will
decrease the gain by a factor REXT/(100 kΩ + REXT) (see Figure
16).
Figure 17. Adjusting for Gains Greater than 20
Rev. PrA | Page 10 of 13
Preliminary Technical Data
AD8203
single-pole filter (20 dB/decade) is formed when the output of
A1 is connected to the input of A2 via the internal 100 kΩ
resistor by strapping Pins 3 and 4 and a capacitor added from
this node to ground, as shown in Figure 18. If a resistor is
added across the capacitor to lower the gain, the corner
frequency will increase; it should be calculated using the
parallel sum of the resistor and 100 kΩ.
GAIN TRIM
Figure 18 shows a method for incremental gain trimming using
a trim potentiometer and external resistor REXT
.
The following approximation is useful for small gain ranges.
∆G ≈ (10 MΩ ÷ REXT)%
5V
Thus, the adjustment range would be ±2% for REXT = 5 MΩ;
±10% for REXT = 1 MΩ, and so on.
OUTPUT
+IN
NC +VS OUT
V
V
DIFF
2
5V
1
OUT
F
=
C
5
2πC10
AD8203
+IN
NC +VS OUT
DIFF
2
C IN FARADS
V
CM
V
V
DIFF
2
–IN GND A1
A2
AD8203
DIFF
2
V
CM
–IN GND A1
A2
C
GAIN TRIM
20kΩ MIN
R
EXT
NC = NO CONNECT
Figure 19. A Single-Pole, Low-Pass Filter Using the Internal 100 kΩ
Signal
NC = NO CONNECT
If the gain is raised using a resistor, as shown in Figure 19, the
corner frequency is lowered by the same factor as the gain is
raised. Thus, using a resistor of 200 kΩ (for which the gain
would be doubled), the corner frequency is now 0.796 Hz µF,
(0.039 µF for a 20 Hz corner frequency.)
Figure 18. Incremental Gain Trim
Internal Signal Overload Considerations
When configuring gain for values other than 20, the maximum
input voltage with respect to the supply voltage and ground
must be considered, since either the preamplifier or the output
buffer will reach its full-scale output (approximately VS – 0.2
V) with large differential input voltages. The input of the
AD8203 is limited to (VS – 0.2) ÷ 10, for overall gains ≤ 10,
since the preamplifier, with its fixed gain of ×10, reaches its
full-scale output before the output buffer. For gains greater than
10, the swing at the buffer output reaches its full scale first and
limits the AD8203 input to (VS – 0.2) ÷ G, where G is the
overall gain.
5V
OUT
+IN
NC +VS OUT
V
V
DIFF
2
C
AD8203
DIFF
2
V
CM
–IN GND A1
A2
255kΩ
FC = 1Hz – µF
LOW-PASS FILTERING
C
In many transducer applications, it is necessary to filter the
signal to remove spurious high frequency components,
including noise, or to extract the mean value of a fluctuating
signal with a peak-to-average ratio (PAR) greater than unity.
For example, a full-wave rectified sinusoid has a PAR of 1.57,
a raised cosine has a PAR of 2, and a half-wave sinusoid has a
PAR of 3.14. Signals having large spikes may have PARs of 10
or more.
NC = NO CONNECT
Figure 20. A 2-Pole, Low-Pass Filter
A 2-pole filter (with a roll-off of 40 dB/decade) can be
implemented using the connections shown in Figure 20. This is a
Sallen-Key form based on a ×2 amplifier. It is useful to remember
that a 2-pole filter with a corner frequency f2 and a 1-pole filter
with a corner at f1 have the same attenuation at the frequency
(f22/f1). The attenuation at that frequency is 40 log (f2/f1). This is
illustrated in Figure 21. Using the standard resistor value shown
and equal capacitors (Figure 20), the corner frequency is
conveniently scaled at 1 Hz µF (0.05 µF for a 20 Hz corner). A
maximally flat response occurs when the resistor is lowered to 196
kΩ and the scaling is then 1.145 Hz µF. The output offset is raised
by approximately 5 mV (equivalent to 250 µV at the input pins).
When implementing a filter, the PAR should be considered so
the output of the AD8203 preamplifier (A1) does not clip
before A2, since this nonlinearity would be averaged and
appear as an error at the output. To avoid this error, both
amplifiers should be made to clip at the same time. This
condition is achieved when the PAR is no greater than the gain
of the second amplifier (2 for the default configuration). For
example, if a PAR of 5 is expected, the gain of A2 should be
increased to 5.
Low-pass filters can be implemented in several ways using the
features provided by the AD8203. In the simplest case, a
Rev. PrA | Page 11 of 13
AD8203
Preliminary Technical Data
FREQUENCY
by a 1-pole, low-pass filter, here set with a corner frequency
equal to 3.6 Hz, which provides about 30 dB of attenuation at
100 Hz. A higher rate of attenuation can be obtained using a 2-
pole filter having fC = 20 Hz, as shown in Figure 23. Although
this circuit uses two separate capacitors, the total capacitance is
less than half that needed for the 1-pole filter.
40dB/DECADE
20dB/DECADE
INDUCTIVE
LOAD
5V
40LOG (f /f )
2
1
CLAMP
DIODE
OUTPUT
+IN
NC +V
OUT
S
432kΩ
BATTERY
14V
A 1-POLE FILTER, CORNER f , AND
1
4 TERM
SHUNT
A 2-POLE FILTER, CORNER f , HAVE
C
AD8203
2
THE SAME ATTENUATION –40LOG (f /f )
2
1
50kΩ
2
f /f
2 1
AT FREQUENCY
–IN GND A1
A2
POWER
DEVICE
2
f /f
2 1
f
f
1
2
127kΩ
Figure 21. Comparative Responses of 1-Pole and 2-Pole Low-Pass
Filters
C
NC = NO CONNECT
COMMON
f = 1Hz µF
C
(0.05µF FOR f = 20Hz)
HIGH-LINE CURRENT SENSING WITH LPF
AND GAIN ADJUSTMENT
C
Figure 23. Illustration of 2-Pole Low-Pass Filtering
Figure 22 is another refinement of Figure 2, including gain
adjustment and low-pass filtering.
DRIVING CHARGE REDISTRIBUTION ADCS
When driving CMOS ADCs, such as those embedded in
popular microcontrollers, the charge injection (∆Q) can cause a
significant deflection in the output voltage of the AD8203.
Though generally of short duration, this deflection may persist
until after the sample period of the ADC has expired, due to the
relatively high open-loop output impedance of the AD8203.
Including an R-C network in the output can significantly reduce
the effect. The capacitor helps to absorb the transient charge,
effectively lowering the high frequency output impedance of
the AD8203. For these applications, the output signal should be
taken from the midpoint of the RLAG − CLAG combination as
shown in Figure 24.
INDUCTIVE
LOAD
5V
OUT
4V/AMP
CLAMP
DIODE
+IN
NC +VS OUT
191kΩ
BATTERY
14V
4 TERM
SHUNT
AD
8
2
0
3
20kΩ
–IN GND A1
A2
POWER
DEVICE
V
OS/IB
NULL
C
NC = NO CONNECT
COMMON
5% CALIBRATION RANGE
= 0.796Hz µF
f
C
(0.22µF FOR f = 3.6Hz)
C
Since the perturbations from the analog-to-digital converter are
small, the output impedance of the AD8203 will appear to be
low. The transient response will, therefore, have a time constant
Figure 22. High-Line Current Sensor Interface;
Gain = ×40, Single-Pole, Low-Pass Filter
governed by the product of the two LAG components, CLAG
×
RLAG. For the values shown in Figure 24, this time constant is
programmed at approximately 10 µs. Therefore, if samples are
taken at several tens of microseconds or more, there will be
negligible charge stack-up.
A power device that is either on or off controls the current in
the load. The average current is proportional to the duty cycle
of the input pulse and is sensed by a small value resistor. The
average differential voltage across the shunt is typically 100
mV, although its peak value will be higher by an amount that
depends on the inductance of the load and the control
frequency. The common-mode voltage, on the other hand,
extends from roughly 1 V above ground when the switch is on,
and to about 1.5 V above the battery voltage when the device is
off, and the clamp diode conducts. If the maximum battery
voltage spikes up to 20 V, the common-mode voltage at the
input can be as high as 21.5 V.
5V
4
6
AD8203
A2
+IN
–IN
RLAG
1kΩ
MICROPROCESSOR
A/D
5
CLAG
0.01µF
10kΩ
10kΩ
To produce a full-scale output of 4 V, a gain ×40 is used,
adjustable by ±5% to absorb the tolerance in the shunt. There is
sufficient headroom to allow 10% over range (to 4.4 V). The
roughly triangular voltage across the sense resistor is averaged
2
Figure 24. Recommended Circuit for Driving CMOS A/D
Rev. PrA | Page 12 of 13
Preliminary Technical Data
OUTLINE DIMENSIONS
AD8203
5.00 (0.1968)
4.80 (0.1890)
8
1
5
4
6.20 (0.2440)
5.80 (0.2284)
4.00 (0.1574)
3.80 (0.1497)
1.27 (0.0500)
BSC
0.50 (0.0196)
0.25 (0.0099)
× 45°
1.75 (0.0688)
1.35 (0.0532)
0.25 (0.0098)
0.10 (0.0040)
8°
0.51 (0.0201)
0.31 (0.0122)
0° 1.27 (0.0500)
COPLANARITY
0.10
0.25 (0.0098)
0.17 (0.0067)
SEATING
PLANE
0.40 (0.0157)
COMPLIANT TO JEDEC STANDARDS MS-012AA
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
Figure 25. 8-Lead Standard Small Outline Package [SOIC]
Narrow Body (R-8)
Dimensions shown in millimeters (inches)
ORDERING GUIDE
Models
Temperature Package
Package Description
Package Outline
R-8
AD8203YR
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +150°C
–40°C to +150°C
SOIC
SOIC
SOIC
AD8203YR-REEL
AD8203YR-REEL7
AD8203CHIPS
AD8203CSURF
R-8
R-8
DIE Form
DIE Form
© 2004 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
PR05013–0–7/04(PrA)
Rev. PrA | Page 13 of 13
相关型号:
©2020 ICPDF网 联系我们和版权申明