AD8222ACPZ-R7 [ADI]
Precision, Dual-Channel Instrumentation Amplifier; 精密,双通道仪表放大器型号: | AD8222ACPZ-R7 |
厂家: | ADI |
描述: | Precision, Dual-Channel Instrumentation Amplifier |
文件: | 总24页 (文件大小:602K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Precision, Dual-Channel
Instrumentation Amplifier
AD8222
FUNCTIONAL BLOCK DIAGRAM
FEATURES
Two channels in small 4 mm × 4 mm LFCSP
Gain set with 1 resistor per amplifier (G = 1 to 10,000)
Low noise
16 15 14 13
AD8222
8 nV/√Hz @ 1 kHz
0.25 μV p-p (0.1 Hz to 10 Hz)
1
2
3
4
12
11
10
9
–IN1
RG1
RG1
+IN1
–IN2
RG2
RG2
+IN2
High accuracy dc performance (B grade)
60 μV maximum input offset voltage
0.3 μV/°C maximum input offset drift
1.0 nA maximum input bias current
126 dB minimum CMRR (G = 100)
Excellent ac performance
150 kHz bandwidth (G = 100)
13 μs settling time to 0.001%
Differential output option (single channel)
Fully specified
5
6
7
8
Figure 1. 4mm × 4 mm LFCSP
Table 1. In Amps and Differential Amplifier by Category
Digital
High
Low
High
Voltage Grade Power
AD85531 AD628
AD6231
AD629
Mil
Low
Prog
Gain
Performance Cost
Adjustable common-mode output
Supply range: 2.3 V to 18 V
AD8221
AD82201
AD8222
AD620 AD6271 AD85551
AD621
AD524
AD526
AD624
AD85561
AD85571
APPLICATIONS
Multichannel data acquisition for
ECG and medical instrumentation
Industrial process controls
Wheatstone bridge sensors
Differential drives for
1 Rail-to-rail output.
High resolution input ADCs
Remote sensors
GENERAL DESCRIPTION
The AD8222 maintains a minimum CMRR of 80 dB to 4 kHz
for all grades at G = 1. High CMRR over frequency allows the
AD8222 to reject wideband interference and line harmonics,
greatly simplifying filter requirements. The AD8222 also has a
typical CMRR drift over temperature of just 0.07 μV/V/°C at G = 1.
The AD8222 is a dual-channel, high performance instrumentation
amplifier that requires only one external resistor per amplifier
to set gains of 1 to 10,000.
The AD8222 is the first dual-instrumentation amplifier in the
small 4 mm × 4mm LFCSP. It requires the same board area as a
typical single instrumentation amplifier. The smaller package
allows a 2× increase in channel density and a lower cost per
channel, all with no compromise in performance.
The AD8222 operates on both single and dual supplies and only
requires 2.2 mA maximum supply current for both amplifiers. It
is specified over the industrial temperature range of −40°C to
+85°C and is fully RoHS compliant.
The AD8222 can also be configured as a single-channel,
differential output instrumentation amplifier. Differential
outputs provide high noise immunity, which can be useful when
the output signal must travel through a noisy environment, such
as with remote sensors. The configuration can also be used to
drive differential input ADCs.
For a single-channel version, see the AD8221.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
©2006 Analog Devices, Inc. All rights reserved.
AD8222
TABLE OF CONTENTS
Features .............................................................................................. 1
Layout .......................................................................................... 16
Solder Wash................................................................................. 17
Input Bias Current Return Path ............................................... 17
Input Protection ......................................................................... 17
RF Interference ........................................................................... 18
Common-Mode Input Voltage Range..................................... 18
Applications..................................................................................... 19
Differential Output .................................................................... 19
Driving a Differential Input ADC............................................ 20
Precision Strain Gauge .............................................................. 20
Driving Cabling.......................................................................... 21
Outline Dimensions....................................................................... 22
Ordering Guide .......................................................................... 22
Applications....................................................................................... 1
Functional Block Diagram .............................................................. 1
General Description......................................................................... 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
Absolute Maximum Ratings............................................................ 6
Thermal Resistance ...................................................................... 6
ESD Caution.................................................................................. 6
Pin Configuration and Function Descriptions............................. 7
Typical Performance Characteristics ............................................. 8
Theory of Operation ...................................................................... 15
Amplifier Architecture .............................................................. 15
Gain Selection............................................................................. 15
Reference Terminal .................................................................... 16
REVISION HISTORY
7/06—Revision 0: Initial Version
Rev. 0 | Page 2 of 24
AD8222
SPECIFICATIONS
VS = 15 V, VREF = 0 V, TA = 25°C, G = 1, RL = 2 kΩ, unless otherwise noted.
Table 2. Single-Ended and Differential1 Output Configuration
A Grade
Typ
B Grade
Typ
Parameter
Conditions
Min
Max
Min
Max
Unit
COMMON-MODE REJECTION
RATIO (CMRR)
VCM = –10 V to +10 V
CMRR DC to 60 Hz
G = 1
G = 10
1 kΩ source imbalance
80
86
dB
dB
dB
dB
100
120
130
106
126
140
G = 100
G = 1000
CMRR at 4 kHz
G = 1
80
80
dB
G = 10
G = 100
G = 1000
CMRR Drift
NOISE
90
100
100
100
110
110
dB
dB
dB
μV/V/°C
T = −40°C to +85°C, G = 1
0.07
0.07
Voltage Noise, 1 kHz
Input Voltage Noise, eNI
Output Voltage Noise, eNO
RTI
RTI Noise = √(eNI2 + (eNO/G)2)
VIN+, VIN−, VREF = 0 V
VIN+, VIN−, VREF = 0 V
8
75
8
75
nV/√Hz
nV/√Hz
f = 0.1 Hz to 10 Hz
G = 1
G = 10
G = 100 to 1000
Current Noise
2
2
μV p-p
μV p-p
μV p-p
fA/√Hz
pA p-p
0.5
0.25
40
6
0.5
0.25
40
6
f = 1 kHz
f = 0.1 Hz to 10 Hz
RTI VOS = (VOSI) + (VOSO/G)
VS = 5 V to 15 V
T = −40°C to +85°C
VOLTAGE OFFSET
Input Offset, VOSI
Overtemperature
Average TC
Output Offset, VOSO
Overtemperature
Average TC
120
150
0.4
500
0.8
9
60
80
0.3
350
0.5
5
μV
μV
μV/°C
μV
mV
VS = 5 V to 15 V
T = −40°C to +85°C
μV/°C
Offset RTI vs. Supply (PSR)
G = 1
G = 10
G = 100
G = 1000
VS = 2.3 V to 18 V
90
110
120
130
140
94
110
130
140
150
dB
dB
dB
dB
110
124
130
114
130
140
INPUT CURRENT (PER CHANNEL)
Input Bias Current
Over temperature
Average TC
Input Offset Current
Overtemperature
Average TC
0.5
2.0
3.0
0.2
1.0
1.5
nA
nA
pA/°C
nA
nA
T = −40°C to +85°C
T = −40°C to +85°C
1
0.2
1
0.1
1
1.5
0.5
0.6
2
1
0.5
pA/°C
REFERENCE INPUT
RIN
IIN
Voltage Range
Gain to Output
20
50
20
50
kΩ
μA
V
VIN+, VIN−, VREF = 0 V
60
+VS
60
+VS
−VS
−VS
V/V
1 ± 0.0001
1 ± 0.0001
Rev. 0 | Page 3 of 24
AD8222
A Grade
Typ
B Grade
Typ
Parameter
Conditions
Min
Max
Min
Max
Unit
GAIN
G = 1 + (49.4 kΩ/RG)
Gain Range
1
10000
1
10000
V/V
Gain Error
VOUT 10 V
G = 1
G = 10
G = 100
G = 1000
0.05
0.3
0.3
0.02
0.15
0.15
0.15
%
%
%
%
0.3
Gain Nonlinearity
G = 1
G = 10
VOUT = –10 V to +10 V
3
7
7
10
20
20
1
7
7
5
20
20
ppm
ppm
ppm
G = 100
Gain vs. Temperature
G = 1
G > 12
3
10
−50
2
5
−50
ppm/°C
ppm/°C
INPUT
Input Impedance
Differential
100||2
100||2
100||2
100||2
GΩ||pF
GΩ||pF
V
V
V
V
Common Mode
Input Operating Voltage Range3
Overtemperature
Input Operating Voltage Range3
Overtemperature
OUTPUT
VS = 2.3 V to 5 V
T = −40°C to +85°C
VS = 5 V to 18 V
T = −40°C to +85°C
RL = 10 kΩ
−VS + 1.9
−VS + 2.0
−VS + 1.9
−VS + 2.0
+VS − 1.1 −VS + 1.9
+VS − 1.2 −VS + 2.0
+VS − 1.2 −VS + 1.9
+VS − 1.2 −VS + 2.0
+VS − 1.1
+VS − 1.2
+VS − 1.2
+VS − 1.2
Output Swing
Overtemperature
Output Swing
Overtemperature
Short-Circuit Current
POWER SUPPLY
Operating Range
Quiescent Current (per Amplifier)
Overtemperature
TEMPERATURE RANGE
Specified Performance
Operational4
VS = 2.3 V to 5 V
T = −40°C to +85°C
VS = 5 V to 18 V
T = −40°C to +85°C
−VS + 1.1
−VS + 1.4
−VS + 1.2
−VS + 1.6
+VS − 1.2 −VS + 1.1
+VS − 1.3 −VS + 1.4
+VS − 1.4 −VS + 1.2
+VS − 1.5 −VS + 1.6
+VS − 1.2
+VS − 1.3
+VS − 1.4
+VS − 1.5
V
V
V
V
18
18
mA
VS = 2.3 V to 18 V
T = −40°C to +85°C
2.3
18
1.1
2.3
18
1.1
1.2
V
mA
mA
0.9
1
0.9
1
1.2
−40
−40
+85
+125
−40
−40
+85
+125
°C
°C
1 Refers to differential configuration shown in Figure 49.
2 Does not include the effects of external resistor RG.
3 One input grounded. G = 1.
4 See Typical Performance Characteristics for expected operation between 85°C to 125°C.
Rev. 0 | Page 4 of 24
AD8222
VS = 15 V, VREF = 0 V, TA = 25°C, RL = 2 kΩ, unless otherwise noted.
Table 3. Single-Ended Output Configuration—Dynamic Performance (Both Amplifiers)
A Grade
Typ
B Grade
Typ
Parameter
Conditions
Min
Max
Min
Max
Unit
DYNAMIC RESPONSE
Small Signal −3 dB Bandwidth
G = 1
1200
750
140
15
1200
750
140
15
kHz
kHz
kHz
kHz
G = 10
G = 100
G =1000
Settling Time 0.01%
G = 1 to 100
G = 1000
Settling Time 0.001%
G = 1 to 100
G = 1000
10 V step
10 V step
10
80
10
80
μs
μs
13
110
13
110
μs
μs
Slew Rate
G = 1
G = 5 to 1000
1.5
2
2
2.5
1.5
2
2
2.5
V/μs
V/μs
Table 4. Differential Output Configuration1—Dynamic Performance
A Grade
Typ
B Grade
Typ
Parameter
Conditions
Min
Max
Min
Max
Unit
DYNAMIC RESPONSE
Small Signal −3 dB Bandwidth
G = 1
1000
650
140
15
1000
650
140
15
kHz
kHz
kHz
kHz
G = 10
G = 100
G =1000
Settling Time 0.01%
G = 1 to 100
G = 1000
Settling Time 0.001%
G = 1 to 100
G = 1000
10 V step
10 V step
15
80
15
80
μs
μs
18
110
18
110
μs
μs
Slew Rate
G = 1
G = 5 to 1000
1.5
2
2
2.5
1.5
2
2
2.5
V/μs
V/μs
1 Refers to differential configuration shown in Figure 49.
Rev. 0 | Page 5 of 24
AD8222
ABSOLUTE MAXIMUM RATINGS
Table 5.
Parameter
THERMAL RESISTANCE
Rating
Table 6.
Supply Voltage
18 V
Thermal Pad
θJA
48
86
Unit
°C/W
°C/W
Output Short-Circuit Current
Input Voltage (Common Mode)
Differential Input Voltage
Storage Temperature Range
Operational Temperature Range
Package Glass Transition Temperature (TG)
ESD (Human Body Model)
ESD (Charge Device Model)
Indefinite
VS
VS
−65°C to +130°C
−40°C to +125°C
130°C
1 kV
1 kV
Soldered to Board
Not Soldered to Board
The θJA values in Table 6 assume a 4-layer JEDEC standard
board. If the thermal pad is soldered to the board, then it is
also assumed it is connected to a plane. θJC at the exposed pad
is 4.4°C/W.
Maximum Power Dissipation
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions may affect device reliability.
The maximum safe power dissipation for the AD8222 is limited
by the associated rise in junction temperature (TJ) on the die. At
approximately 130°C, which is the glass transition temperature,
the plastic changes its properties. Even temporarily exceeding
this temperature limit may change the stresses that the package
exerts on the die, permanently shifting the parametric performance
of the amplifiers. Exceeding a temperature of 130°C for an
extended period can result in a loss of functionality.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. 0 | Page 6 of 24
AD8222
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
PIN 1
12
11
–IN1 1
RG1 2
RG1 3
+IN1 4
–IN2
RG2
INDICATOR
AD8222
TOP VIEW
10 RG2
+IN2
9
Figure 2. Pin Configuration
Table 7. Pin Function Descriptions
Pin No
Mnemonic
−IN1
RG1
RG1
+IN1
+VS
Description
1
2
3
4
Negative Input In-Amp 1
Gain Resistor In-Amp 1
Gain Resistor In-Amp 1
Positive Input In-Amp 1
Positive Supply
5
6
7
8
REF1
REF2
−VS
Reference Adjust In-Amp 1
Reference Adjust In-Amp 2
Negative Supply
9
+IN2
RG2
RG2
−IN2
−VS
OUT2
OUT1
+VS
Positive Input In-Amp 2
Gain Resistor In-Amp 2
Gain Resistor In-Amp 2
Negative Input In-Amp 2
Negative Supply
Output In-Amp 2
Output In-Amp 1
Positive Supply
10
11
12
13
14
15
16
Rev. 0 | Page 7 of 24
AD8222
TYPICAL PERFORMANCE CHARACTERISTICS
N = 1713
500
800
600
400
200
0
400
300
200
100
0
–50 –40 –30 –20 –10
0
10
20
30
40
50
–2.0
–1.5
–1.0
–0.5
0
0.5
1.0
1.5
2.0
CMRR (µV/V)
I
(nA)
OFFSET
Figure 6. Typical Distribution of Input Offset Current
Figure 3. Typical Distribution for CMRR (G = 1)
15
10
5
N = 1713
300
250
200
150
100
10
V
= ±15V
S
0
V
= ±5V
S
–5
–10
–15
0
–100 80
60
40
20
0
20
40
60
80
100
–15
–10
–5
0
5
10
15
V
(µV)
OSI
OUTPUT VOLTAGE (V)
Figure 4. Typical Distribution of Input Offset Voltage
Figure 7. Input Common-Mode Range vs. Output Voltage, G = 1
15
10
N = 1713
700
600
500
400
300
200
100
0
V
= ±15V
S
5
0
V
= ±5V
S
–5
–10
–15
–15
–2.0
–1.5
–1.0
–0.5
0
0.5
1.0
1.5
2.0
–10
–5
0
5
10
15
I
(nA)
BIAS
OUTPUT VOLTAGE (V)
Figure 5. Typical Distribution of Input Bias Current
Figure 8. Input Common-Mode Range vs. Output Voltage, G = 100
Rev. 0 | Page 8 of 24
AD8222
200
150
100
50
160
150
140
130
120
110
100
90
BANDWIDTH
LIMITED
V
= ±15V
= ±5V
S
GAIN = 1000
0
80
GAIN = 100
GAIN = 10
GAIN = 1
V
70
S
–50
–100
–150
–200
60
50
40
30
20
10
0
–15
–10
–5
0
5
10
15
0.1
1
10
100
1k
10k
100k
1M
COMMON-MODE VOLTAGE (V)
FREQUENCY (Hz)
Figure 12. Positive PSRR vs. Frequency, RTI (G = 1 to 1000)
Figure 9. IBIAS vs. Common-Mode Voltage
160
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
150
140
130
120
110
100
90
GAIN = 1000
GAIN = 100
80
70
60
50
40
GAIN = 10
GAIN = 1
30
20
10
0
0.1
1
10
100
1k
10k
100k
1M
0
2
4
6
8
10
FREQUENCY (Hz)
WARM-UP TIME (Minutes)
Figure 10. Change in Input Offset Voltage vs. Warm-Up Time
Figure 13. Negative PSRR vs. Frequency, RTI (G = 1 to 1000)
1000
10k
800
600
NEGATIVE
1k
100
10
400
GAIN = 1
GAIN = 10 GAIN = 100
200
POSITIVE
0
OFFSET CURRENT
–200
–400
–600
–800
–1000
GAIN = 1000
1
–55
–35
–15
5
25
45
65
85
105
125
1
10
100
1k
10k
100k
1M
10M
TEMPERATURE (°C)
SOURCE RESISTANCE (Ω)
Figure 11. Input Bias Current and Offset Current vs. Temperature
Figure 14. Total Drift vs. Source Resistance
Rev. 0 | Page 9 of 24
AD8222
70
20
15
GAIN = 1000
60
50
GAIN = 100
GAIN = 10
GAIN = 1
10
40
30
5
EXAMPLE PART 1
EXAMPLE PART 2
20
0
10
–5
0
–10
–20
–30
–40
–10
–15
–20
100
1k
10k
100k
1M
10M
–40
–20
0
20
40
60
80
100
120
FREQUENCY (Hz)
TEMPERATURE (°C)
Figure 15. Gain vs. Frequency
Figure 18. ΔCMR vs. Temperature, G = 1
160
150
140
130
120
110
100
90
+V –0
S
GAIN = 1000
GAIN = 100
–0.4
–0.8
–1.2
–1.6
–2.0
FROM +V
GAIN = 10
GAIN = 1
BANDWIDTH
LIMITED
+2.0
+1.6
+1.2
+0.8
+0.4
FROM –V
80
70
60
50
–V +0
S
40
0.1
2
6
10
14
18
1
10
100
1k
10k
100k
1M
SUPPLY VOLTAGE (V)
FREQUENCY (Hz)
Figure 16. CMRR vs. Frequency, RTI
Figure 19. Input Voltage Limit vs. Supply Voltage, G = 1
160
150
140
130
120
110
100
90
+V –0
S
GAIN = 1000
–0.4
–0.8
–1.2
–1.6
R
L
= 10kΩ
GAIN = 100
GAIN = 10
R
R
= 2kΩ
= 2kΩ
L
BANDWIDTH
LIMITED
+1.6
+1.2
+0.8
+0.4
L
80
70
GAIN = 1
60
R
L
= 10kΩ
50
–V +0
S
40
0.1
2
6
10
14
18
1
10
100
1k
10k
100k
1M
SUPPLY VOLTAGE (V)
FREQUENCY (Hz)
Figure 17. CMRR vs. Frequency, RTI, 1 kΩ Source Imbalance
Figure 20. Output Voltage Swing vs. Supply Voltage, G = 1
Rev. 0 | Page 10 of 24
AD8222
30
20
10
0
40
30
20
2kΩ LOAD
10
0
600Ω LOAD
–10
–20
–30
–40
10kΩ LOAD
–10
–8
–6
–4
–2
0
2
4
6
8
10
1
10
100
1k
10k
V
(V)
LOAD RESISTANCE (Ω)
OUT
Figure 24. Gain Nonlinearity, G = 100
Figure 21. Output Voltage Swing vs. Load Resistance
1k
100
10
+V –0
S
–1
–2
–3
SOURCING
GAIN = 1
GAIN = 10
GAIN = 100
+3
+2
+1
GAIN = 1000
SINKING
GAIN = 1000
BW LIMIT
1
–V +0
S
1
10
100
1k
10k
100k
0
1
2
3
4
5
6
7
8
9
10 11 12
FREQUENCY (Hz)
OUTPUT CURRENT (mA)
Figure 25. Voltage Noise Spectral Density vs. Frequency (G = 1 to 1000)
Figure 22. Output Voltage Swing vs. Output Current, G = 1
4
3
2
1
10kΩ LOAD
0
2kΩ LOAD
–1
600Ω LOAD
–2
–3
–4
2µV/DIV
1s/DIV
–10
–8
–6
–4
–2
0
2
4
6
8
10
V
(V)
OUT
Figure 23. Gain Nonlinearity, G = 1
Figure 26. 0.1 Hz to 10 Hz RTI Voltage Noise (G = 1)
Rev. 0 | Page 11 of 24
AD8222
30
25
20
15
10
5
GAIN = 10, 100, 1000
GAIN = 1
0
1k
0.1µV/DIV
1s/DIV
10k
100k
FREQUENCY (Hz)
1M
Figure 27. 0.1 Hz to 10 Hz RTI Voltage Noise (G = 1000)
Figure 30. Large Signal Frequency Response
1k
100
10
5V/DIV
7.4µs TO 0.01%
8.3µs TO 0.001%
0.002%/DIV
20µs/DIV
1
10
100
1k
10k
100k
FREQUENCY (Hz)
Figure 31. Large Signal Pulse Response and Settling Time (G = 1)
Figure 28. Current Noise Spectral Density vs. Frequency
5V/DIV
4.8µs TO 0.01%
6.6µs TO 0.001%
0.002%/DIV
20µs/DIV
5pA/DIV
1s/DIV
Figure 32. Large Signal Pulse Response and Settling G = 10)
Figure 29. 0.1 Hz to 10 Hz Current Noise
Rev. 0 | Page 12 of 24
AD8222
5V/DIV
9.2µs TO 0.01%
16.2µs TO 0.001%
0.002%/DIV
20mV/DIV
4µs/DIV
20µs/DIV
Figure 33. Large Signal Pulse Response and Settling Time (G = 100)
Figure 36. Small Signal Response, G = 10, RL = 2 kΩ, CL = 100 pF
5V/DIV
83µs TO 0.01%
112µs TO 0.001%
0.002%/DIV
20mV/DIV
10µs/DIV
200µs/DIV
Figure 34. Large Signal Pulse Response and Settling Time (G = 1000)
Figure 37. Small Signal Response, G = 100, RL = 2 kΩ, CL = 100 pF
20mV/DIV
4µs/DIV
20mV/DIV
100µs/DIV
Figure 38. Small Signal Response, G = 1000, RL = 2 kΩ, CL = 100 pF
Figure 35. Small Signal Response, G = 1, RL = 2 kΩ, CL = 100 pF
Rev. 0 | Page 13 of 24
AD8222
15
60
40
GAIN = 1000
GAIN = 100
10
20
SETTLED TO 0.001%
GAIN = 10
GAIN = 1
0
SETTLED TO 0.01%
5
–20
–40
0
0
5
10
15
20
100
1k
10k
100k
1M
10M
OUTPUT VOLTAGE STEP SIZE (V)
FREQUENCY (Hz)
Figure 39. Settling Time vs. Step Size (G = 1)
Figure 42. Differential Output Configuration: Gain vs. Frequency
1k
100
10
100
V
DIFF_OUT
CMR
= 20 log
OUT
90
80
70
60
50
40
30
20
10
0
V
CM_OUT
LIMITED BY
MEASUREMENT
SYSTEM
SETTLED TO 0.001%
SETTLED TO 0.01%
1
1
10
100
1k
1
10
100
1k
10k
100k
1M
GAIN
FREQUENCY (Hz)
Figure 40. Settling Time vs. Gain for a 10 V Step
Figure 43. Differential Output Configuration:
Common-Mode Output vs. Frequency
200
SOURCE
= 20V p-p
SOURCE V
OUT
SMALLER TO
V
OUT
AVOID SLEW
RATE LIMIT
180
160
140
120
100
80
GAIN = 1000
THERMAL CROSSTALK
VARIES WITH LOAD
GAIN = 1
60
1
10
100
1k
10k
100k
1M
FREQUENCY (Hz)
Figure 41. Channel Separation vs. Frequency, RL = 2 kΩ, Source Channel at G = 1
Rev. 0 | Page 14 of 24
AD8222
THEORY OF OPERATION
V
I
I
B
A1
A2
I
COMPENSATION
I
COMPENSATION
B
B
10kΩ
C1
C2
+V
–V
S
10kΩ
10kΩ
OUTPUT
A3
+V
–V
S
+V
S
+V
–V
R1 24.7kΩ
R2 24.7kΩ
+V
S
S
400Ω
+V
400Ω
S
S
Q2
–IN
Q1
+IN
REF
10kΩ
R
G
–V
S
S
S
–V
–V
S
S
Figure 44. Simplified Schematic
AMPLIFIER ARCHITECTURE
GAIN SELECTION
The two instrumentation amplifiers of the AD8222 are based on
the classic three op amp topology. Figure 44 shows a simplified
schematic of one of the amplifiers. Input Transistors Q1 and Q2
are biased at a fixed current. Any differential input signal forces
the output voltages of A1 and A2 to change so that the differential
voltage also appears across RG. The current that flows through
RG must also flow through R1 and R2, resulting in a precisely
amplified version of the differential input signal between the
outputs of A1 and A2. Topologically, Q1, A1, and R1 and Q2,
A2, and R2 can be viewed as precision current feedback
amplifiers. The common-mode signal and the amplified
differential signal are applied to a difference amplifier that
rejects the common-mode voltage. The difference amplifier
employs innovations that result in low output offset voltage as
well as low output offset voltage drift.
Placing a resistor across the RG terminals sets the gain of the
AD8222, which can be calculated by referring to Table 8 or by
using the following gain equation.
49.4 kꢀ
RG =
G −1
Table 8. Gains Achieved Using 1% Resistors
1% Standard Table Value of RG (Ω)
Calculated Gain
49.9 k
12.4 k
5.49 k
2.61 k
1.00 k
499
1.990
4.984
9.998
19.93
50.40
100.0
249
199.4
100
49.9
495.0
991.0
Because the input amplifiers employ a current feedback
architecture, the gain-bandwidth product of the AD8222
increases with gain, resulting in a system that does not suffer
from the expected bandwidth loss of voltage feedback
architectures at higher gains.
The AD8222 defaults to G = 1 when no gain resistor is used.
The tolerance and gain drift of the RG resistor should be added
to the AD8222’s specifications to determine the total gain
accuracy of the system. When the gain resistor is not used,
gain error and gain drift are kept to a minimum.
The transfer function of the AD8222 is
V
OUT = G(VIN+ − VIN−) + VREF
where
49.4 kꢀ
G =1+
RG
Rev. 0 | Page 15 of 24
AD8222
Thermal Pad
REFERENCE TERMINAL
The AD8222’s 4 mm × 4 mm LFCSP comes with a thermal pad.
This pad is connected internally to −VS. The pad can either be
left unconnected or connected to the negative supply rail.
The output voltage of the AD8222 is developed with respect to
the potential on the reference terminal. This is useful when the
output signal needs to be offset to a precise midsupply level. For
example, a voltage source can be tied to the REF pin to level-
shift the output so that the AD8222 can drive a single-supply
ADC. The REF pin is protected with ESD diodes and should
not exceed either +VS or −VS by more than 0.3 V.
To preserve maximum pin compatibility with future dual
instrumentation amplifiers, leave the pad unconnected. This
can be done by not soldering the paddle at all or by soldering
the part to a landing that is a not connected to any other net.
For high vibration applications, a landing is recommended.
For best performance, source impedance to the REF terminal
should be kept below 1 Ω. As shown in Figure 44, the reference
terminal, REF, is at one end of a 10 kꢀ resistor. Additional
impedance at the REF terminal adds to this 10 kꢀ resistor and
results in amplification of the signal connected to the positive
input. The amplification from the additional RREF can be
computed by
Because the AD8222 dissipates little power, heat dissipation is
rarely an issue. If improved heat dissipation is desired (for example,
when driving heavy loads), connect the thermal pad to the
negative supply rail. For the best heat dissipation performance,
the negative supply rail should be a plane in the board. See
the section for thermal coefficients with and without the pad
soldered.
2
(
10 kꢀ + RREF
20 kꢀ + RREF
)
Common-Mode Rejection over Frequency
The AD8222 has a higher CMRR over frequency than typical
in-amps, which gives it greater immunity to disturbances, such
as line noise and its associated harmonics. A well-implemented
layout is required to maintain this high performance. Input
source impedances should be matched closely. Source resistance
should be placed close to the inputs so that it interacts with as
little parasitic capacitance as possible.
Only the positive signal path is amplified; the negative path is
unaffected. This uneven amplification degrades the amplifier’s
CMRR.
INCORRECT
CORRECT
CORRECT
AD8222
AD8222
AD8222
V
V
Parasitics at the RGx pins can also affect CMRR over frequency.
The PCB should be laid out so that the parasitic capacitances at
each pin match. Traces from the gain setting resistor to the RGx
pins should be kept short to minimize parasitic inductance.
REF
REF
V
REF
+
+
AD8222
–
OP2177
–
Reference
Errors introduced at the reference terminal feed directly to the
output. Care should be taken to tie REF to the appropriate local
ground.
Figure 45. Driving the Reference Pin
LAYOUT
The AD8222 is a high precision device. To ensure optimum
performance at the PC board level, care must be taken in the
design of the board layout. The AD8222 pinout is arranged in a
logical manner to aid in this task.
Power Supplies
A stable dc voltage should be used to power the instrumentation
amplifier. Noise on the supply pins can adversely affect
performance.
Package Considerations
The AD8222 has two positive supply pins (Pin 5 and Pin 16)
and two negative supply pins (Pin 8 and Pin 13). While the part
functions with only one pin from each supply pair connected,
both pins should be connected for specified performance and
optimum reliability.
The AD8222 comes in a 4 mm × 4 mm LFCSP. Beware of
blindly copying the footprint from another 4 mm × 4 mm
LFCSP part; it may not have the same thermal pad size and
leads. Refer to the Outline Dimensions section to verify that
the PCB symbol has the correct dimensions. Space between the
leads and thermal pad should be kept as wide as possible for the
best bias current performance.
Rev. 0 | Page 16 of 24
AD8222
INCORRECT
+V
CORRECT
+V
The AD8222 should be decoupled with 0.1 μF bypass capacitors,
one for each supply. The positive supply decoupling capacitor
should be placed near Pin 16, and the negative supply
decoupling capacitor should be placed near Pin 8. Each supply
should also be decoupled with a 10 μF tantalum capacitor. The
tantalum capacitor can be placed further away from the
AD8222 and can generally be shared by other precision integrated
circuits. Figure 46 shows an example layout.
S
S
AD8222
AD8222
REF
REF
REF
REF
–V
–V
S
S
TRANSFORMER
TRANSFORMER
+V
+V
S
S
0.1µF
AD8222
AD8222
REF
16
15
14
13
10MΩ
AD8222
–V
–V
S
S
12
11
10
9
1
2
3
4
THERMOCOUPLE
THERMOCOUPLE
R
R
G
+V
S
+V
S
G
C
C
C
R
1
fHIGH-PASS
=
AD8222
2πRC
AD8222
5
6
7
8
C
REF
R
–V
–V
S
S
CAPACITIVELY COUPLED
CAPACITIVELY COUPLED
0.1µF
Figure 47. Creating an IBIAS Path
INPUT PROTECTION
All terminals of the AD8222 are protected against ESD (1 kV—
human body model). In addition, the input structure allows for
dc overload conditions of about 2½ V beyond the supplies.
Figure 46. Example Layout
SOLDER WASH
Input Voltages Beyond the Rails
The solder process can leave flux and other contaminants on
the board. When these contaminants are between the AD8222
leads and thermal pad, they can create leakage paths that are
larger than the AD8222’s bias currents. A thorough washing
process removes these contaminants and restores the AD8222’s
excellent bias current performance.
For larger input voltages, an external resistor should be used in
series with each input to limit current during overload conditions.
The AD8222 can safely handle a continuous 6 mA current. The
limiting resistor can be computed from
VIN −VSUPPLY
RLIMIT
≥
− 400 ꢀ
6 mA
INPUT BIAS CURRENT RETURN PATH
The input bias current of the AD8222 must have a return path
to common. When the source, such as a thermocouple, cannot
provide a return current path, one should be created, as shown
in Figure 47.
For applications where the AD8222 encounters extreme overload
voltages, such as cardiac defibrillators, external series resistors
and low leakage diode clamps, such as the BAV199L, the FJH1100s,
or the SP720, should be used.
Rev. 0 | Page 17 of 24
AD8222
+15V
Differential Input Voltages at High Gains
When operating at high gain, large differential input voltages
can cause more than 6 mA of current to flow into the inputs.
This condition occurs when the differential voltage exceeds
the following critical voltage
0.1µF
10µF
C
1nF
C
R
+IN
R1
4.02kΩ
V
C
D
10nF
OUT
V
CRITICAL = (400 + RG) × (6 mA)
AD8222
499Ω
R
REF
This is true for differential voltages of either polarity.
–IN
4.02kΩ
C
C
1nF
The maximum allowed differential voltage can be increased by
adding an input protection resistor in series with each input.
The value of each protection resistor should be
0.1µF
10µF
–15V
R
PROTECT = (VDIFF_MAX − VCRITICAL)/6 mA
Figure 48. RFI Suppression
RF INTERFERENCE
Figure 48 shows an example where the differential filter
frequency is approximately 2 kHz, and the common-mode filter
frequency is approximately 40 kHz.
RF rectification is often a problem when amplifiers are used in
applications where there are strong RF signals. The disturbance
can appear as a small dc offset voltage. High frequency signals
can be filtered with a low-pass, RC network placed at the input
of the instrumentation amplifier, as shown in Figure 48. The
filter limits the input signal bandwidth according to the
following relationship.
Values of R and CC should be chosen to minimize RFI.
Mismatch between the R × CC at the positive input and the
R × CC at negative input degrades the CMRR of the AD8222. By
using a value of CD 10× larger than the value of CC, the effect of
the mismatch is reduced and performance is improved.
1
FilterFreqDiff =
2π R(2CD + CC)
COMMON-MODE INPUT VOLTAGE RANGE
The three op amp architecture of the AD8222 applies gain and
then removes the common-mode voltage. Therefore, internal
nodes in the AD8222 experience a combination of both the
gained signal and the common-mode signal. This combined
signal can be limited by the voltage supplies even when the
individual input and output signals are not. Figure 7 and Figure 8
show the allowable common-mode input voltage ranges for
various output voltages, supply voltages, and gains.
1
FilterFreqCM =
2π RCC
where CD ≥ 10CC.
Rev. 0 | Page 18 of 24
AD8222
APPLICATIONS
DIFFERENTIAL OUTPUT
Setting the Common-Mode Voltage
The output common-mode voltage is set by the average of +IN2
and REF2. The transfer function is
The differential configuration of the AD8222 has the same
excellent dc precision specifications as the single-ended output
configuration and is recommended for applications in the
frequency range of dc to 100 kHz.
V
CM_OUT = (V+OUT + V−OUT)/2 = (V+IN2 + VREF2)/2
+IN2 and REF2 have different properties that allow the
reference voltage to be easily set for a wide variety of applications.
+IN2 has high impedance but cannot swing to the supply rails
of the part. REF2 must be driven with a low impedance but can
go 300 mV beyond the supply rails.
The circuit configuration is shown in Figure 49. The differential
output specification in Table 2 and Table 4 refer to this
configuration only. The circuit includes an RC filter that maintains
the stability of the loop.
The transfer function for the differential output is:
A common application sets the common-mode output voltage
to the midscale of a differential ADC. In this case, the ADC
reference voltage would be sent to the +IN2 terminal, and
ground would be connected to the REF2 terminal. This would
produce a common-mode output voltage of half the ADC
reference voltage.
V
DIFF_OUT = V+OUT − V−OUT = (V+IN − V−IN) × G
where
49.4 kꢀ
G =1 +
RG
2-Channel Differential Output Using a Dual Op Amp
+IN
+
Another differential output topology is shown in Figure 50.
Instead of a second in-amp, ½ of a dual OP2177 op amp creates
the inverted output. Because the OP2177 comes in an MSOP,
this configuration allows the creation of a dual channel,
precision differential output in-amp with little board area.
R
+OUT
AD8222
–
G
10kΩ
–IN
–
100pF
AD8222
+
+IN2
Errors from the op amp are common to both outputs and are
thus common mode. Errors from mismatched resistors also
create a common-mode dc offset. Because these errors are
common mode, they will likely be rejected by the next device
in the signal chain.
REF2
–OUT
Figure 49. Differential Circuit Schematic
+IN
+OUT
AD8222
–IN
4.99kΩ
REF
V
REF
–
+
4.99kΩ
OP2177
–OUT
Figure 50. Differential Output Using Op Amp
Rev. 0 | Page 19 of 24
AD8222
+12V
+
10µF
0.1µF
+5V
100pF
NPO
5%
0.1µF
1kΩ
+IN
–IN
1kΩ
1kΩ
VDD
+OUT
–OUT
IN+
IN–
AD8222
AD7688
GND REF
1000pF
(DIFF OUT)
1kΩ
2200pF
2200pF
REF2
+IN2
100pF
NPO
5%
10µF
X5R
+12V
+5V REF
–12V
0.1µF
10µF
0.1µF
+
V
IN
V
+5V REF
OUT
0.1µF
ADR435
GND
Figure 51. Driving a Differential ADC
The 1 kΩ resistors can also protect an ADC from overvoltages.
Because the AD8222 runs on wider supply voltages than a
typical ADC, there is a possibility of overdriving the ADC. This
is not an issue with a PulSAR® converter, such as the AD7688.
Its input can handle a 130 mA overdrive, which is much higher
than the short-circuit limit of the AD8222. However, other
converters have less robust inputs and may need the added
protection.
DRIVING A DIFFERENTIAL INPUT ADC
The AD8222 can be configured in differential output mode
to drive a differential analog-to-digital converter. Figure 51
illustrates several of the concepts.
First Antialiasing Filter
The 1 kΩ resistor, 1000 pF capacitor, and 100 pF capacitors in
front of the in-amp form a 76 kHz filter. This is the first of two
antialiasing filters in the circuit and helps to reduce the noise of
the system. The 100 pF capacitors protect against common-
mode RFI signals. Note that they are 5% COG/NPO types.
These capacitors match well over time and temperature, which
keeps the system’s CMRR high over frequency.
Reference
The ADR435 supplies a reference voltage to both the ADC and
the AD8222. Because REF2 on the AD8222 is grounded, the
common-mode output voltage is precisely half the reference
voltage, exactly where it needs to be for the ADC.
Second Antialiasing Filter
PRECISION STRAIN GAUGE
A 1 kΩ resistor and 2200 pF capacitor are located between each
AD8222 output and ADC input. They create a 72 kHz low-pass
filter for another stage of antialiasing protection.
The low offset and high CMRR over frequency of the
AD8222 make it an excellent candidate for both ac and dc
bridge measurements. As shown in Figure 52, the bridge can
be connected to the inputs of the amplifier directly.
These four elements also help distortion performance. The
2200 pF capacitor provides charge to the switched capacitor
front end of the ADC, while the 1 kΩ resistor shields the
AD8222 from driving any sharp current changes. If the
application requires a lower frequency antialiasing filter and is
distortion sensitive, increase the value of the capacitor rather
than the resistor.
5V
10µF
0.1µF
350Ω
350Ω
350Ω
350Ω
+IN
–IN
+
R
AD8222
G
–
2.5V
Figure 52. Precision Strain Gauge
Rev. 0 | Page 20 of 24
AD8222
DRIVING CABLING
AD8222
All cables have a certain capacitance per unit length, which
varies widely with cable type. The capacitive load from the cable
may cause peaking in the AD8222’s output response. To reduce
the peaking, use a resistor between the AD8222 and the cable.
Because cable capacitance and desired output response vary
widely, this resistor is best determined empirically. A good
starting point is 50 Ω.
(DIFF OUT)
AD8222
(SINGLE OUT)
The AD8222 operates at a low enough frequency that
transmission line effects are rarely an issue; therefore, the
resistor need not match the characteristic impedance of
the cable.
Figure 53. Driving a Cable
Rev. 0 | Page 21 of 24
AD8222
OUTLINE DIMENSIONS
0.50
0.40
0.30
4.00
BSC SQ
0.60 MAX
PIN 1
INDICATOR
1
12
13
16
PIN 1
INDICATOR
2.65
2.50 SQ
2.35
3.75
BSC SQ
EXPOSED
PAD
4
8
5
0.65
BSC
9
0.25 MIN
TOP VIEW
1.95 BCS
BOTTOM VIEW
12° MAX
0.80 MAX
0.65 TYP
1.00
0.85
0.80
0.05 MAX
0.02 NOM
SEATING
PLANE
0.30
0.23
0.18
COPLANARITY
0.08
0.20 REF
COMPLIANT TO JEDEC STANDARDS MO-220-VGGC.
Figure 54. 16-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
4 mm × 4 mm Body, Very Thin Quad
(CP-16-13)
Dimensions are shown in millimeters
ORDERING GUIDE
Model
Temperature Range
−40°C to +85°C
Product Description
16-Lead LFCSP_VQ
16-Lead LFCSP_VQ
16-Lead LFCSP_VQ
16-Lead LFCSP_VQ
16-Lead LFCSP_VQ
16-Lead LFCSP_VQ
Evaluation Board
Package Option
CP-16-13
CP-16-13
CP-16-13
CP-16-13
AD8222ACPZ-R71
AD8222ACPZ-RL1
AD8222ACPZ-WP1
AD8222BCPZ-R71
AD8222BCPZ-RL1
AD8222BCPZ-WP1
AD8222-EVAL
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
CP-16-13
CP-16-13
1 Z = Pb-free part.
Rev. 0 | Page 22 of 24
AD8222
NOTES
Rev. 0 | Page 23 of 24
AD8222
NOTES
©2006 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D05947-0-7/06(0)
Rev. 0 | Page 24 of 24
相关型号:
©2020 ICPDF网 联系我们和版权申明