AD9235BRUZ-40 [ADI]
12-Bit, 20/40/65 MSPS 3 V A/D Converter; 12位20/40/65 MSPS 3 V A / D转换器型号: | AD9235BRUZ-40 |
厂家: | ADI |
描述: | 12-Bit, 20/40/65 MSPS 3 V A/D Converter |
文件: | 总40页 (文件大小:838K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
12-Bit, 20/40/65 MSPS
3 V A/D Converter
AD9235
Data Sheet
FEATURES
FUNCTIONAL BLOCK DIAGRAM
AVDD
DRVDD
Single 3 V supply operation (2.7 V to 3.6 V)
SNR = 70 dBc to Nyquist at 65 MSPS
SFDR = 85 dBc to Nyquist at 65 MSPS
Low power: 300 mW at 65 MSPS
Differential input with 500 MHz bandwidth
On-chip reference and SHA
VIN+
VIN–
8-STAGE
1 1/2-BIT
PIPELINE
SHA
A/D
MDAC1
4
16
3
REFT
REFB
A/D
DNL = 0.4 LSB
CORRECTION LOGIC
12
Flexible analog input: 1 V p-p to 2 V p-p range
Offset binary or twos complement data format
Clock duty cycle stabilizer
OUTPUT BUFFERS
OTR
D11
AD9235
VREF
D0
CLOCK
DUTY CYCLE
STABILIZER
APPLICATIONS
Ultrasound equipment
IF sampling in communications receivers
IS-95, CDMA-One, IMT-2000
Battery-powered instruments
Hand-held scopemeters
MODE
SELECT
SENSE
REF
SELECT
0.5V
AGND
CLK
PDWN
MODE
DGND
Figure 1.
Low cost digital oscilloscopes
GENERAL DESCRIPTION
can be used with the most significant bit to determine low or
high overflow.
The AD9235 is a family of monolithic, single 3 V supply, 12-bit,
20/40/65 MSPS analog-to-digital converters (ADCs). This
family features a high performance sample-and-hold amplifier
(SHA) and voltage reference. The AD9235 uses a multistage
differential pipelined architecture with output error correction
logic to provide 12-bit accuracy at 20/40/65 MSPS data rates
and guarantee no missing codes over the full operating
temperature range.
Fabricated on an advanced CMOS process, the AD9235 is avail-
able in a 28-lead TSSOP and a 32-lead LFCSP and is specified
over the industrial temperature range (–40°C to +85°C).
PRODUCT HIGHLIGHTS
1. The AD9235 operates from a single 3 V power supply and
features a separate digital output driver supply to accommo-
date 2.5 V and 3.3 V logic families.
2. Operating at 65 MSPS, the AD9235 consumes a low 300 m W.
3. The patented SHA input maintains excellent performance for
input frequencies up to 100 MHz and can be configured for
single-ended or differential operation.
4. The AD9235 pinout is similar to the AD9214-65, a 10-bit,
65 MSPS ADC. This allows a simplified upgrade path from
10 bits to 12 bits for 65 MSPS systems.
The wide bandwidth, truly differential SHA allows a variety of
user-selectable input ranges and offsets including single-ended
applications. It is suitable for multiplexed systems that switch
full-scale voltage levels in successive channels and for sampling
single-channel inputs at frequencies well beyond the Nyquist rate.
Combined with power and cost savings over previously available
ADCs, the AD9235 is suitable for applications in communica-
tions, imaging, and medical ultrasound.
5. The clock DCS maintains overall ADC performance over a
wide range of clock pulse widths.
6. The OTR output bit indicates when the signal is beyond the
selected input range.
A single-ended clock input is used to control all internal
conversion cycles. A duty cycle stabilizer (DCS) compensates
for wide variations in the clock duty cycle while maintaining
excellent overall ADC performance. The digital output data is
presented in straight binary or twos complement formats. An
out-of-range (OTR) signal indicates an overflow condition that
Rev. D
Information furnishedby Analog Devices is believedto be accurate andreliable. However, nore-
sponsibility is assumed by Analog Devices for its use, nor for anyinfringements of patentsor other
rightsofthird partiesthat may result from its use. Specifications subject to change without notice. No
license isgrantedbyimplication or otherwise under anypatent or patent rights of Analog Devices.
Trademarks andregisteredtrademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
©2012 Analog Devices, Inc. All rights reserved.
AD9235
Data Sheet
TABLE OF CONTENTS
Specifications..................................................................................... 3
Applying the AD9235 .................................................................... 15
Theory of Operation .................................................................. 15
Analog Input ............................................................................... 15
Clock Input Considerations...................................................... 16
Power Dissipation and Standby Mode .................................... 17
Digital Outputs ........................................................................... 18
Voltage Reference ....................................................................... 18
Operational Mode Selection..................................................... 19
TSSOP Evaluation Board .......................................................... 19
LFCSP Evaluation Board........................................................... 20
Outline Dimensions....................................................................... 36
Ordering Guide .......................................................................... 37
DC Specifications ......................................................................... 3
Digital Specifications ................................................................... 4
Switching Specifications .............................................................. 4
AC Specifications.......................................................................... 5
Absolute Maximum Ratings............................................................ 7
Explanation of Test Levels........................................................... 7
ESD Caution.................................................................................. 7
Pin Configurations and Function Descriptions ........................... 8
Definitions of Specifications ........................................................... 9
Equivalent Circuits ......................................................................... 10
Typical Performance Characteristics ........................................... 11
REVISION HISTORY
Changes to TPCs 1 to 12 ..................................................................9
Changes to Theory of Operation Section.....................................13
Changes to Analog Input Section..................................................13
Changes to Single-ended Input Configuration Section .............14
Replaced Figure 8 ............................................................................14
Changes to Clock Input Considerations Section ........................14
Changes to Table I ...........................................................................15
Changes to Power Dissipation and Standby Mode Section.......15
Changes to Digital Outputs Section..............................................15
Changes to Timing Section............................................................15
Changes to Figure 13.......................................................................16
Changes to Figures 16 to 26 ...........................................................17
Added LFCSP Evaluation Board Section .....................................17
Inserted Figures 27 to 35 ................................................................25
Added Table III................................................................................30
Updated Outline Dimensions........................................................31
10/12—Rev. C to Rev. D
Changes to Figure 4 and Table 6 ................................................................8
Updated Outline Dimensions (Changed CP-32-2 to CP-32-7)..... 36
Changes to Ordering Guide .......................................................... 37
10/04—Data Sheet changed from Rev. B to Rev. C
Changes to Format .............................................................Universal
Changes to Specifications .................................................................3
Changes to the Ordering Guide.................................................... 37
5/03—Data Sheet changed from Rev. A to Rev. B
Added CP-32 Package (LFCSP)........................................Universal
Changes to Several Pin Names..........................................Universal
Changes to Features...........................................................................1
Changes to Product Description .....................................................1
Changes to Product Highlights........................................................1
Changes to Specifications .................................................................2
Replaced Figure 1 ..............................................................................3
Changes to Absolute Maximum Ratings........................................5
Changes to Ordering Guide .............................................................5
Changes to Pin Function Descriptions...........................................6
New Definitions of Specifications Section .....................................7
8/02—Data Sheet changed from Rev. 0 to Rev. A
Updated RU-28 Package................................................................ 24
Rev. D | Page 2 of 40
Data Sheet
AD9235
SPECIFICATIONS
DC SPECIFICATIONS
AV DD = 3 V, DRVDD = 2.5 V, maximum sample rate, 2 V p-p differential input, 1.0 V internal reference, TMIN to TMAX
,
unless otherwise noted.
Table 1.
AD9235BRU/BCP-20 AD9235BRU/BCP-40 AD9235BRU/BCP-65
Test
Temp Level Min Typ
Parameter
Max
Min Typ
Max
Min Typ
Max
Unit
RESOLUTION
Full
VI
12
12
12
Bits
ACCURACY
No Missing Codes Guaranteed
Offset Error
Full
Full
Full
Full
25°C
Full
25°C
VI
VI
VI
IV
I
12
12
12
Bits
0.30
0.30
0.35
0.35
0.45
0.40
1.20
2.40
0.65
0.50
1.20
2.50
0.75
0.50
1.20 % FSR
2.60 % FSR
0.80 LSB
LSB
1.30 LSB
LSB
Gain Error1
0.50
0.35
0.35
0.50
0.40
0.50
0.40
0.35
0.70
0.45
Differential Nonlinearity (DNL)2
Integral Nonlinearity (INL)2
IV
I
0.80
0.90
TEMPERATURE DRIFT
Offset Error
Gain Error
Full
Full
V
V
2
12
2
12
3
12
ppm/°C
ppm/°C
INTERNAL VOLTAGE REFERENCE
Output Voltage Error (1 V Mode)
Load Regulation @ 1.0 mA
Full
Full
VI
V
V
5
35
5
35
5
35
mV
mV
mV
mV
0.8
2.5
0.1
0.8
2.5
0.1
0.8
2.5
0.1
Output Voltage Error (0.5 V Mode) Full
Load Regulation @ 0.5 mA
INPUT REFERRED NOISE
VREF = 0.5 V
Full
V
25°C
25°C
V
V
0.54
0.27
0.54
0.27
0.54
0.27
LSB rms
LSB rms
VREF = 1.0 V
ANALOG INPUT
Input Span, VREF = 0.5 V
Input Span, VREF = 1.0 V
Input Capacitance3
REFERENCE INPUT RESISTANCE
POWER SUPPLIES
Supply Voltages
AVDD
Full
Full
Full
Full
IV
IV
V
1
2
7
7
1
2
7
7
1
2
7
7
V p-p
V p-p
pF
V
kΩ
Full
Full
IV
IV
2.7
3.0
2.25 3.0
3.6
3.6
2.7
3.0
2.25 3.0
3.6
3.6
2.7
3.0
2.25 3.0
3.6
3.6
V
V
DRVDD
Supply Current
IAVDD2
Full
Full
Full
V
V
V
30
2
0.01
55
5
0.01
100
7
0.01
mA
mA
% FSR
IDRVDD2
PSRR
POWER CONSUMPTION
DC Input4
Sine Wave Input2
Standby Power5
Full
Full
Full
V
VI
V
90
95
1.0
165
180
1.0
300
320
1.0
mW
mW
mW
110
205
350
1 Gain error and gain temperature coefficient are based on the ADC only (with a fixed 1.0 V external reference).
2 Measured at maximum clock rate, fIN = 2.4 MHz, full-scale sine wave, with approximately 5 pF loading on each output bit.
3 Input capacitance refers to the effective capacitance between one differential input pin and AGND. Refer to Figure 5 for the equivalent analog input structure.
4 Measured with dc input at maximum clock rate.
5 Standby power is measured with a dc input, the CLK pin inactive (i.e., set to AVDD or AGND).
Rev. D | Page 3 of 40
AD9235
Data Sheet
DIGITAL SPECIFICATIONS
Table 2.
AD9235BRU/BCP-20
AD9235BRU/BCP-40
AD9235BRU/BCP-65
Test
Temp Level Min
Parameter
Typ
Max
Min
Typ
Max
Min
Typ
Max
Unit
LOGIC INPUTS
High Level Input Voltage
Low Level Input Voltage
High Level Input Current
Low Level Input Current
Input Capacitance
LOGIC OUTPUTS1
Full
Full
Full
Full
Full
IV
IV
IV
IV
V
2.0
2.0
2.0
V
V
µA
µA
pF
0.8
+10
+10
0.8
+10
+10
0.8
+10
+10
–10
–10
–10
–10
–10
–10
2
2
2
DRVDD = 3.3 V
High-Level Output Voltage
(IOH = 50 µA)
High-Level Output Voltage
(IOH = 0.5 mA)
Low-Level Output Voltage
(IOL = 1.6 mA)
Low-Level Output Voltage
(IOL = 50 µA)
Full
Full
Full
Full
IV
IV
IV
IV
3.29
3.25
3.29
3.25
3.29
3.25
V
V
V
V
0.2
0.2
0.2
0.05
0.05
0.05
DRVDD = 2.5 V
High-Level Output Voltage
(IOH = 50 µA)
High-Level Output Voltage
(IOH = 0.5 mA)
Low-Level Output Voltage
(IOL = 1.6 mA)
Low-Level Output Voltage
(IOL = 50 µA)
Full
Full
Full
Full
IV
IV
IV
IV
2.49
2.45
2.49
2.45
2.49
2.45
V
V
V
V
0.2
0.2
0.2
0.05
0.05
0.05
1 Output voltage levels measured with 5 pF load on each output.
SWITCHING SPECIFICATIONS
Table 3.
AD9235BRU/BCP-20
AD9235BRU/BCP-40
AD9235BRU/BCP-65
Test
Parameter
Temp Level Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Unit
CLOCK INPUT PARAMETERS
Maximum Conversion Rate
Minimum Conversion Rate
CLK Period
CLK Pulse-Width High1
CLK Pulse-Width Low1
DATA OUTPUT PARAMETERS
Output Delay2 (tPD)
Pipeline Delay (Latency)
Aperture Delay (tA)
Aperture Uncertainty Jitter (tJ)
Wake-Up Time3
Full
Full
Full
Full
Full
VI
V
V
V
V
20
40
65
MSPS
MSPS
ns
ns
ns
1
1
1
50.0
15.0
15.0
25.0
8.8
8.8
15.4
6.2
6.2
Full
Full
Full
Full
Full
Full
V
V
V
V
V
V
3.5
7
1.0
0.5
3.0
1
3.5
7
1.0
0.5
3.0
1
3.5
7
1.0
0.5
3.0
2
ns
Cycles
ns
ps rms
ms
OUT-OF-RANGE RECOVERY TIME
Cycles
1 For the AD9235-65 model only, with duty cycle stabilizer enabled. DCS function not applicable for -20 and -40 models.
2 Output delay is measured from CLK 50% transition to DATA 50% transition, with 5 pF load on each output.
3 Wake-up time is dependent on value of decoupling capacitors; typical values shown with 0.1 µF and 10 µF capacitors on REFT and REFB.
Rev. D | Page 4 of 40
Data Sheet
AD9235
N+1
tA
N
N+2
N+8
N–1
N+3
ANALOG
INPUT
N+7
N+4
N+6
N+5
CLK
DATA
OUT
N–9
N–8
N–7
N–6
N–5
N–4
N–3
N–2
N–1
N
tPD = 6.0ns MAX
2.0ns MIN
Figure 2. Timing Diagram
AC SPECIFICATIONS
AVDD = 3 V, DRVDD = 2.5 V, maximum sample rate, 2 V p-p differential input, AIN = –0.5 dBFS, 1.0 V internal reference, TMIN to TMAX
,
unless otherwise noted.
Table 4.
AD9235BRU/BCP-20 AD9235BRU/BCP-40 AD9235BRU/BCP-65
Parameter
Temp Test Level Min Typ
Max
Min Typ
Max
Min Typ
Max
Unit
SIGNAL-TO-NOISE RATIO
fINPUT = 2.4 MHz
fINPUT = 9.7 MHz
25°C
Full
25°C
Full
25°C
Full
25°C
25°C
V
IV
I
IV
I
IV
I
V
70.8
70.0 70.4
70.6
70.6
70.5
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
fINPUT = 19.6 MHz
fINPUT = 32.5 MHz
fINPUT = 100 MHz
69.9 70.3
70.4
68.7 69.7
70.1
68.7
68.5
70.5
68.3
SIGNAL-TO-NOISE RATIO
AND DISTORTION
fINPUT = 2.4 MHz
fINPUT = 9.7 MHz
25°C
Full
25°C
Full
25°C
Full
25°C
25°C
V
IV
I
IV
I
IV
I
V
70.6
69.9 70.3
70.5
70.4
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
fINPUT = 19.6 MHz
fINPUT = 32.5 MHz
69.7 70.2
70.3
68.3 69.5
69.9
fINPUT = 100 MHz
68.6
68.3
67.8
TOTAL HARMONIC DISTORTION
fINPUT = 2.4 MHz
fINPUT = 9.7 MHz
25°C
Full
25°C
Full
25°C
Full
25°C
25°C
V
IV
I
IV
I
IV
I
V
–88.0
–86.0 –79.0
–87.4
–89.0
–87.5
dBc
dBc
dBc
dBc
dBc
fINPUT = 19.6 MHz
fINPUT = 32.5 MHz
fINPUT = 100 MHz
–85.5 –79.0
–86.0
–81.8 –74.0 dBc
–82.0
–78.0
dBc
dBc
–84.0
–82.5
WORST HARMONIC
(SECOND OR THIRD)
fINPUT = 9.7 MHz
fINPUT = 19.6 MHz
fINPUT = 32.5 MHz
Full
Full
Full
IV
IV
IV
–90.0 –80.0
dBc
dBc
–90.0 –80.0
–83.5 –74.0 dBc
Rev. D | Page 5 of 40
AD9235
Data Sheet
AD9235BRU/BCP-20 AD9235BRU/BCP-40 AD9235BRU/BCP-65
Parameter
Temp Test Level Min Typ
Max
Min Typ
Max
Min Typ
Max
Unit
SPURIOUS-FREE DYNAMIC RANGE
fINPUT = 2.4 MHz
fINPUT = 9.7 MHz
25°C
Full
25°C
Full
25°C
Full
25°C
25°C
V
IV
I
IV
I
IV
I
V
92.0
80.0 88.5
91.0
92.0
92.0
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
fINPUT = 19.6 MHz
fINPUT = 32.5 MHz
fINPUT = 100 MHz
80.0 89.0
90.0
74.0 83.0
85.0
84.0
85.0
80.5
Rev. D | Page 6 of 40
Data Sheet
AD9235
ABSOLUTE MAXIMUM RATINGS
Table 5.
Absolute maximum ratings are limiting values to be applied
With
individually and beyond which the serviceability of the circuit
may be impaired. Functional operability is not necessarily
implied. Exposure to absolute maximum rating conditions for
an extended period of time may affect device reliability.
Pin Name
ELECTRICAL
AVDD
DRVDD
AGND
AVDD
Digital
Outputs
CLK, MODE
VIN+, VIN–
VREF
SENSE
REFB, REFT
PDWN
Respect to Min
Max
Unit
AGND
DGND
DGND
DRVDD
DGND
–0.3
–0.3
–0.3
–3.9
–0.3
+3.9
+3.9
+0.3
+3.9
V
V
V
V
V
EXPLANATION OF TEST LEVELS
Test
Levels
DRVDD + 0.3
Description
I
100% production tested.
AGND
AGND
AGND
AGND
AGND
AGND
–0.3
–0.3
–0.3
–0.3
–0.3
–0.3
AVDD + 0.3
AVDD + 0.3
AVDD + 0.3
AVDD + 0.3
AVDD + 0.3
AVDD + 0.3
V
V
V
V
V
V
II
100% production tested at 25°C and sample tested at
specified temperatures.
III
Sample tested only.
IV
Parameter is guaranteed by design and characteriza-
tion testing.
V
Parameter is a typical value only.
ENVIRONMENTAL1
VI
100% production tested at 25°C; guaranteed by de-
sign and characterization testing for industrial tem-
perature range; 100% production tested at tempera-
ture extremes for military devices.
Operating Temperature
Junction Temperature
Lead Temperature (10 sec)
Storage Temperature
–40
–65
+85
150
300
°C
°C
°C
°C
+150
1 Typical thermal impedances (28-lead TSSOP), θJA = 67.7°C/W; (32-lead
LFCSP), θJA = 32.5°C/W, θJC = 32.71°C/W. These measurements were taken on
a 4-layer board in still air, in accordance with EIA/JESD51-1.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate
on the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy elec-
trostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation
or loss of functionality.
Rev. D | Page 7 of 40
AD9235
Data Sheet
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
1
2
28
27
26
25
24
23
22
21
20
19
18
17
16
15
OTR
MODE
SENSE
VREF
REFB
REFT
AVDD
AGND
VIN+
D11 (MSB)
D10
3
D9
DNC 1
24 VREF
23
4
D8
2
CLK
SENSE
5
AD9235
TOP VIEW
(Not to Scale)
DRVDD
DGND
D7
DNC 3
PDWN 4
22 MODE
21 OTR
AD9235
6
TOP VIEW
5
6
7
8
20
19
18
DNC
DNC
D0 (LSB)
D1
D11 (MSB)
D10
D9
7
(Not to Scale)
8
D6
9
D5
17 D8
10
11
12
13
14
VIN–
D4
AGND
AVDD
CLK
D3
D2
D1
NOTES
PDWN
D0 (LSB)
1. DNC = DO NOT CONNECT.
2. IT IS RECOMMENDED THAT THE EXPOSED PADDLE
BE SOLDERED TO THE GROUND PLANE.
Figure 3. 28-Lead TSSOP Pin Configuration
Figure 4. 32-Lead LFCSP Pin Configuration
Table 6. Pin Function Descriptions
Pin No.
28-Lead TSSOP
Pin No.
32-Lead LFCSP Mnemonic
Description
1
21
OTR
Out-of-Range Indicator.
2
3
4
5
6
7, 12
8, 11
9
22
23
24
25
26
27, 32
28, 31
29
MODE
SENSE
VREF
REFB
REFT
AVDD
AGND
VIN+
VIN–
Data Format and Clock Duty Cycle Stabilizer (DCS) Mode Selection.
Reference Mode Selection.
Voltage Reference Input/Output.
Differential Reference (−).
Differential Reference (+).
Analog Power Supply.
Analog Ground.
Analog Input Pin (+).
Analog Input Pin (−).
10
30
13
2
CLK
Clock Input Pin.
14
4
PDWN
Power-Down Function Selection (Active High).
15 to 22, 25 to 28
7 to 14, 17 to 20
D0 (LSB) to D11 (MSB) Data Output Bits.
23
24
15
16
DGND
DRVDD
Digital Output Ground.
Digital Output Driver Supply. Must be decoupled to DGND with a minimum.
0.1 µF capacitor. Recommended decoupling is 0.1 µF in parallel with 10 µF.
Do Not Connect.
Exposed Pad. It is recommended that the exposed paddle be soldered to the
ground plane. There is an increased reliability of the solder joints and maxi-
mum thermal capability of the package is achieved with exposed paddle
soldered to the customer board.
1, 3, 5, 6
EP
DNC
EPAD
Rev. D | Page 8 of 40
Data Sheet
AD9235
DEFINITIONS OF SPECIFICATIONS
Analog Bandwidth (Full Power Bandwidth)
The analog input frequency at which the spectral power of the
fundamental frequency (as determined by the FFT analysis) is
reduced by 3 dB.
Signal-to-Noise and Distortion (SINAD)1
The ratio of the rms signal amplitude (set 0.5 dB below full
scale) to the rms value of the sum of all other spectral compo-
nents below the Nyquist frequency, including harmonics but
excluding dc.
Aperture Delay (tA)
The delay between the 50% point of the rising edge of the clock
and the instant at which the analog input is sampled.
Effective Number of Bits (ENOB)
The ENOB for a device for sine wave inputs at a given input
frequency can be calculated directly from its measured SINAD
using the following formula
Aperture Jitter (tJ)
The sample-to-sample variation in aperture delay.
N = (SINAD − 1.76)/6.02
Integral Nonlinearity (INL)
The deviation of each individual code from a line drawn from
negative full scale through positive full scale. The point used as
negative full scale occurs ½ LSB before the first code transition.
Positive full scale is defined as a level 1 ½ LSBs beyond the last
code transition. The deviation is measured from the middle of
each particular code to the true straight line.
Signal-to-Noise Ratio (SNR)1
The ratio of the rms signal amplitude (set at 0.5 dB below full
scale) to the rms value of the sum of all other spectral compo-
nents below the Nyquist frequency, excluding the first six
harmonics and dc.
Spurious-Free Dynamic Range (SFDR)1
Differential Nonlinearity (DNL, No Missing Codes)
An ideal ADC exhibits code transitions that are exactly 1 LSB
apart. DNL is the deviation from this ideal value. Guaranteed
no missing codes to 12-bit resolution indicates that all 4096
codes must be present over all operating ranges.
The difference in dB between the rms amplitude of the input
signal and the peak spurious signal.
Two-Tone SFDR1
The ratio of the rms value of either input tone to the rms value
of the peak spurious component. The peak spurious component
may or may not be an IMD product.
Offset Error
The major carry transition should occur for an analog value
½ LSB below VIN+ = VIN–. Offset error is defined as the
deviation of the actual transition from that point.
Clock Pulse Width and Duty Cycle
Pulse-width high is the minimum amount of time that the
clock pulse should be left in the Logic 1 state to achieve rated
performance. Pulse-width low is the minimum time the clock
pulse should be left in the low state. At a given clock rate, these
specifications define an acceptable clock duty cycle.
Gain Error
The first code transition should occur at an analog value ½ LSB
above negative full scale. The last transition should occur at an
analog value 1 ½ LSB below the positive full scale. Gain error is
the deviation of the actual difference between first and last code
transitions and the ideal difference between first and last code
transitions.
Minimum Conversion Rate
The clock rate at which the SNR of the lowest analog signal
frequency drops by no more than 3 dB below the
guaranteed limit.
Temperature Drift
The temperature drift for offset error and gain error specifies
the maximum change from the initial (25°C) value to the value
Maximum Conversion Rate
The clock rate at which parametric testing is performed.
at TMIN or TMAX
.
Output Propagation Delay (tPD
)
The delay between the clock logic threshold and the time when
all bits are within valid logic levels.
Power Supply Rejection Ratio
The change in full scale from the value with the supply
at the minimum limit to the value with the supply at its
maximum limit.
Out-of-Range Recovery Time
The time it takes for the ADC to reacquire the analog input
after a transition from 10% above positive full scale to 10%
above negative full scale, or from 10% below negative full scale
to 10% below positive full scale.
Total Harmonic Distortion (THD)1
The ratio of the rms sum of the first six harmonic components
to the rms value of the measured input signal.
1 AC specifications may be reported in dBc (degrades as signal levels are
lowered) or in dBFS (always related back to converter full scale).
Rev. D | Page 9 of 40
AD9235
Data Sheet
EQUIVALENT CIRCUITS
AVDD
DRVDD
VIN+, VIN–
D11–D0,
OTR
Figure 5. Equivalent Analog Input Circuit
Figure 7. Equivalent Digital Output Circuit
AVDD
AVDD
CLK,
MODE
PDWN
20kΩ
Figure 6. Equivalent MODE Input Circuit
Figure 8. Equivalent Digital Input Circuit
Rev. D | Page 10 of 40
Data Sheet
AD9235
TYPICAL PERFORMANCE CHARACTERISTICS
AVDD = 3.0 V, DRVDD = 2.5 V, fSAMPLE = 65 MSPS with DCS disabled, TA = 25°C, 2 V differential input, AIN = −0.5 dBFS, VREF = 1.0 V,
unless otherwise noted.
0
100
95
90
85
80
75
70
65
60
55
50
SNR = 70.3dBc
SFDR (2V DIFF)
SINAD = 70.2dBc
ENOB = 11.4 BITS
THD = –86.3dBc
SFDR = 89.9dBc
–20
–40
SNR (2V SE)
–60
–80
SNR (2V DIFF)
–100
–120
SFDR (2V SE)
45
0
6.5
13.0
19.5
26.0
32.5
40
50
55
60
65
FREQUENCY (MHz)
SAMPLE RATE (MSPS)
Figure 9. Single Tone 8K FFT with fIN = 10 MHz
Figure 12. AD9235-65: Single Tone SNR/SFDR vs.
CLK with fIN = Nyquist (32.5 MHz)
f
0
–20
100
95
90
85
80
75
70
65
60
55
50
SNR = 69.4dBc
SINAD = 69.1dBc
ENOB = 11.2 BITS
THD = –81.0dBc
SFDR = 83.8dBc
–40
SFDR (2V DIFF)
SNR (2V SE)
SNR (2V DIFF)
–60
–80
SFDR (2V SE)
–100
–120
65.0
71.5
78.0
84.5
91.0
20
25
30
SAMPLE RATE (MSPS)
35
40
FREQUENCY (MHz)
Figure 10. Single Tone 8K FFT with fIN = 70 MHz
Figure 13. AD9235-40: Single Tone SNR/SFDR vs. fCLK with fIN = Nyquist (20 MHz)
0
100
SNR = 68.5dBc
SFDR (2V DIFF)
95
SINAD = 66.5dBc
ENOB = 10.8 BITS
THD = –71.0dBc
SFDR = 71.2dBc
–20
90
85
–40
–60
SFDR (2V SE)
80
75
SNR (2V SE)
70
–80
65
SNR (2V DIFF)
60
55
50
–100
–120
97.5
104.0
110.5
117.0
123.5
130.0
0
5
10
15
20
FREQUENCY (MHz)
SAMPLE RATE (MSPS)
Figure 11. Single Tone 8K FFT with fIN = 100 MHz
Figure 14. AD9235-20: Single Tone SNR/SFDR vs. fCLK with fIN = Nyquist (10 MHz)
Rev. D | Page 11 of 40
AD9235
Data Sheet
100
95
90
85
80
75
70
65
SFDR
SFDR
DIFFERENTIAL (dBFS)
SINGLE-ENDED (dBFS)
90
SFDR
DIFFERENTIAL (dBc)
SFDR
SNR
DIFFERENTIAL (dBFS)
80
70
60
50
40
SNR
SINGLE-ENDED (dBFS)
SFDR
SINGLE-ENDED (dBc)
SNR
SNR
SINGLE-ENDED (dBc)
SNR
DIFFERENTIAL (dBc)
–30
–25
–20
–15
–10
–5
0
0
25
50
75
100
125
A
(dBFS)
INPUT FREQUENCY (MHz)
IN
Figure 18. AD9235-65: SNR/SFDR vs. fIN
Figure 15. AD9235-65: Single Tone SNR/SFDR vs.
IN with fIN = Nyquist (32.5 MHz)
A
95
90
85
80
75
70
65
100
90
80
70
60
50
40
SFDR
DIFFERENTIAL (dBFS)
SFDR
SFDR
SINGLE-ENDED
(dBFS)
SFDR
DIFFERENTIAL
(dBc)
SNR
DIFFERENTIAL
(dBFS)
SNR
SINGLE-ENDED
(dBFS)
SFDR
SINGLE-ENDED (dBc)
SNR
DIFFERENTIAL (dBc)
SNR
SNR
SINGLE-ENDED (dBc)
0
25
50
75
100
125
–30
–25
–20
–15
–10
–5
0
INPUT FREQUENCY (MHz)
A
(dBFS)
IN
Figure 19. AD9235-40: SNR/SFDR vs. fIN
Figure 16. AD9235-40: Single Tone SNR/SFDR vs. AIN with fIN = Nyquist (20 MHz)
95
90
85
80
75
70
65
100
SFDR DIFFERENTIAL (dBFS)
SFDR
90
DIFFERENTIAL (dBc)
SFDR
SFDR
SINGLE-ENDED (dBFS)
SFDR
80
70
60
50
40
SNR
SINGLE-ENDED(dBc)
DIFFERENTIAL (dBFS)
SNR
SINGLE-ENDED (dBFS)
SNR
DIFFERENTIAL(dBc)
SNR
SNR
SINGLE-ENDED (dBc)
0
25
50
75
100
125
–30
–25
–20
–15
–10
–5
0
INPUT FREQUENCY (MHz)
A
(dBFS)
IN
Figure 20. AD9235-20: SNR/SFDR vs. fIN
Figure 17. AD9235-20: Single Tone SNR/SFDR vs. AIN with fIN = Nyquist (10 MHz)
Rev. D | Page 12 of 40
Data Sheet
AD9235
0
95
90
85
80
75
70
65
60
SNR = 64.6dBFS
SFDR = 81.6dBFS
2V SFDR
1V SFDR
–20
–40
–60
–80
2V SNR
1V SNR
–100
–120
32.5
39.0
45.5
52.0
58.5
65.0
–24
–21
–18
–15
(dBFS)
–12
–9
–6
FREQUENCY (MHz)
A
IN
Figure 21. Dual Tone 8K FFT with fIN1 = 45 MHz and fIN2 = 46 MHz
Figure 24. Dual Tone SNR/SFDR vs. AIN with fIN1 = 45 MHz and fIN2 = 46 MHz
95
0
SNR = 64.3dBFS
2V SFDR
SFDR = 81.1dBFS
90
–20
1V SFDR
85
80
75
–40
–60
–80
2V SNR
1V SNR
70
–100
65
60
–24
–120
65.0
–21
–18
–15
–12
–9
–6
71.5
78.0
84.5
91.0
97.5
A
(dBFS)
FREQUENCY (MHz)
IN
Figure 22. Dual Tone 8K FFT with fIN1 = 69 MHz and fIN2 = 70 MHz
Figure 25. Dual Tone SNR/SFDR vs. AIN with fIN1 = 69 MHz and fIN2 = 70 MHz
0
95
SNR = 62.5dBFS
SFDR = 75.6dBFS
2V SFDR
90
–20
–40
1V SFDR
85
80
75
–60
–80
2V SNR
1V SNR
70
–100
65
–120
130.0
60
–24
136.5
143.0
149.5
156.0
162.0
–21
–18
–15
–12
–9
–6
FREQUENCY (MHz)
A
(dBFS)
IN
Figure 23. Dual Tone 8K FFT with fIN1 = 144 MHz and fIN2 = 145 MHz
Figure 26. Dual Tone SNR/SFDR vs. AIN with fIN1 = 144 MHz and fIN2 = 145 MHz
Rev. D | Page 13 of 40
AD9235
Data Sheet
20
15
75
12.2
11.7
11.2
10.7
10.2
9.7
AD9235-40:
2V SINAD
AD9235-65:
2V SINAD
AD9235-20:
2V SINAD
72
69
66
63
60
10
5
AD9235-20:
1V SINAD
AD9235-40:
1V SINAD
0
–5
AD9235-65:
1V SINAD
–10
–15
–20
0
10
20
30
40
50
60
–40
–20
0
20
40
60
80
SAMPLE RATE (MSPS)
TEMPERATURE (°C)
Figure 27. SINAD vs. fCLK with fIN = Nyquist
Figure 30. A/D Gain vs. Temperature Using an External Reference
90
1.0
0.8
SFDR: DCS ON
80
70
60
50
40
30
0.6
SFDR: DCS OFF
SINAD: DCS ON
0.4
0.2
SINAD: DCS OFF
0
–0.2
–0.4
–0.6
–0.8
–1.0
35
40
45
50
55
60
65
0
500
1000 1500 2000 2500 3000 3500 4000
CODE
DUTY CYCLE (%)
Figure 28. SINAD/SFDR vs. Clock Duty Cycle
Figure 31. Typical INL
90
85
80
75
70
65
60
55
50
1.0
0.8
SFDR 2V DIFF
0.6
0.4
SFDR 1V DIFF
SINAD 2V DIFF
0.2
0
–0.2
–0.4
–0.6
–0.8
–1.0
SINAD 1V DIFF
–40 –30 –20 –10
0
10 20 30 40 50 60 70 80
0
500
1000
1500 2000 2500
CODE
3000
3500
4000
SAMPLE RATE (MSPS)
Figure 29. SINAD/SFDR vs. Temperature with fIN = 32.5 MHz
Figure 32. Typical DNL
Rev. D | Page 14 of 40
Data Sheet
AD9235
APPLYING THE AD9235
For best dynamic performance, the source impedances driving
VIN+ and VIN– should be matched such that common-mode
settling errors are symmetrical. These errors are reduced by the
common-mode rejection of the ADC.
THEORY OF OPERATION
The AD9235 architecture consists of a front end SHA followed
by a pipelined switched capacitor ADC. The pipelined ADC is
divided into three sections, consisting of a 4-bit first stage
followed by eight 1.5-bit stages and a final 3-bit flash. Each stage
provides sufficient overlap to correct for flash errors in the
preceding stages. The quantized outputs from each stage are
combined into a final 12-bit result in the digital correction log-
ic. The pipelined architecture permits the first stage to operate
on a new input sample while the remaining stages operate on
preceding samples. Sampling occurs on the rising edge
of the clock.
H
T
T
5pF
5pF
VIN+
VIN–
C
C
PAR
T
PAR
Each stage of the pipeline, excluding the last, consists of a low
resolution flash ADC connected to a switched capacitor DAC
and interstage residue amplifier (MDAC). The residue amplifier
magnifies the difference between the reconstructed DAC output
and the flash input for the next stage in the pipeline. One bit of
redundancy is used in each stage to facilitate digital correction
of flash errors. The last stage simply consists of a flash ADC.
T
H
Figure 33. Switched-Capacitor SHA Input
An internal differential reference buffer creates positive and
negative reference voltages, REFT and REFB, respectively, that
define the span of the ADC core. The output common mode of
the reference buffer is set to midsupply, and the REFT and
REFB voltages and span are defined as:
The input stage contains a differential SHA that can be ac- or
dc-coupled in differential or single-ended modes. The output-
staging block aligns the data, carries out the error correction,
and passes the data to the output buffers. The output buffers are
powered from a separate supply, allowing adjustment of the
output voltage swing. During power-down, the output buffers
go into a high impedance state.
REFT = ½(AVDD + VREF)
REFB = ½(AVDD − VREF)
Span = 2 × (REFT − REFB) = 2 × VREF
ANALOG INPUT
It can be seen from the equations above that the REFT and
REFB voltages are symmetrical about the midsupply voltage
and, by definition, the input span is twice the value of the
VREF voltage.
The analog input to the AD9235 is a differential switched
capacitor SHA that has been designed for optimum perfor-
mance while processing a differential input signal. The SHA
input can support a wide common-mode range and maintain
excellent performance, as shown in Figure 34. An input
common-mode voltage of midsupply minimizes signal-
dependent errors and provides optimum performance.
90
85
80
75
70
65
60
55
50
–90
–85
–80
–75
–70
–65
–60
–55
–50
THD 2.5MHz 2V DIFF
THD 35MHz 2V DIFF
SNR 2.5MHz 2V DIFF
Referring to Figure 33, the clock signal alternatively switches
the SHA between sample mode and hold mode. When the SHA
is switched into sample mode, the signal source must be capable
of charging the sample capacitors and settling within one-half
of a clock cycle. A small resistor in series with each input can
help reduce the peak transient current required from the output
stage of the driving source. Also, a small shunt capacitor can be
placed across the inputs to provide dynamic charging currents.
This passive network creates a low-pass filter at the ADC’s
input; therefore, the precise values are dependent upon the
application. In IF undersampling applications, any shunt
capacitors should be removed. In combination with the driving
source impedance, they would limit the input bandwidth.
SNR 35MHz 2V DIFF
0
0.5
1.0
1.5
2.0
2.5
3.0
COMMON-MODE LEVEL (V)
Figure 34. AD9235-65: SNR, THD vs. Common-Mode Level
Rev. D | Page 15 of 40
AD9235
Data Sheet
The internal voltage reference can be pin-strapped to fixed
values of 0.5 V or 1.0 V, or adjusted within the same range as
discussed in the Internal Reference Connection section. Maxi-
mum SNR performance is achieved with the AD9235 set to the
largest input span of 2 V p-p. The relative SNR degradation is
3 dB when changing from 2 V p-p mode to 1 V p-p mode.
differential transformer coupling is the recommended input
configuration, as shown in Figure 36.
AVDD
22Ω
VIN+
15pF
AD9235
2Vp-p
49.9Ω
22Ω
The SHA may be driven from a source that keeps the signal
peaks within the allowable range for the selected reference volt-
age. The minimum and maximum common-mode input levels
are defined as:
VIN–
AGND
1kΩ
15pF
0.1µF
1kΩ
Figure 36. Differential Transformer-Coupled Configuration
VCMMIN = VREF/2
The signal characteristics must be considered when selecting a
transformer. Most RF transformers saturate at frequencies
below a few MHz, and excessive signal power can also cause
core saturation, which leads to distortion.
VCMMAX = (AVDD + VREF)/2
The minimum common-mode input level allows the AD9235 to
accommodate ground-referenced inputs.
Single-Ended Input Configuration
Although optimum performance is achieved with a differential
input, a single-ended source may be driven into VIN+ or VIN–.
In this configuration, one input accepts the signal, while the
opposite input should be set to midscale by connecting it to an
appropriate reference. For example, a 2 V p-p signal may be
applied to VIN+ while a 1 V reference is applied to VIN–. The
AD9235 then accepts an input signal varying between 2 V and
0 V. In the single-ended configuration, distortion performance
may degrade significantly as compared to the differential case.
However, the effect is less noticeable at lower input frequencies and
in the lower speed grade models (AD9235-40 and AD9235-20).
A single-ended input may provide adequate performance in
cost-sensitive applications. In this configuration, there is degra-
dation in SFDR and in distortion performance due to the large
input common-mode swing. However, if the source
impedances on each input are matched, there should be little
effect on SNR performance. Figure 37 details a typical single-
ended input configuration.
1kΩ
AVDD
VIN+
0.33µF
22Ω
2Vp-p
49.9Ω
1kΩ
1kΩ
15pF
Differential Input Configurations
AD9235
As previously detailed, optimum performance is achieved while
driving the AD9235 in a differential input configuration. For
baseband applications, the AD8138 differential driver provides
excellent performance and a flexible interface to the ADC. The
output common-mode voltage of the AD8138 is easily set to
AVDD/2, and the driver can be configured in a Sallen-Key filter
topology to provide band limiting of the input signal.
22Ω
VIN–
AGND
10µF
0.1µF
15pF
1kΩ
Figure 37. Single-Ended Input Configuration
CLOCK INPUT CONSIDERATIONS
Typical high speed ADCs use both clock edges to generate a
variety of internal timing signals, and as a result, may be sensi-
tive to clock duty cycle. Commonly a 5% tolerance is required
on the clock duty cycle to maintain dynamic performance char-
acteristics. The AD9235 contains a clock duty cycle stabilizer
(DCS) that retimes the nonsampling edge, providing an internal
clock signal with a nominal 50% duty cycle. This allows a wide
range of clock input duty cycles without affecting the perfor-
mance of the AD9235. As shown in Figure 30, noise and distor-
tion performance are nearly flat over a 30% range of duty cycle.
49.9Ω
1Vp-p
499Ω
AVDD
VIN+
22Ω
499Ω
523Ω
1kΩ
15pF
AD9235
AD8138
499Ω
22Ω
VIN–
AGND
0.1µF
1kΩ
15pF
Figure 35. Differential Input Configuration Using the AD8138
The duty cycle stabilizer uses a delay-locked loop (DLL) to
create the nonsampling edge. As a result, any changes to the
sampling frequency require approximately 100 clock cycles to
allow the DLL to acquire and lock to the new rate.
At input frequencies in the second Nyquist zone and above, the
performance of most amplifiers is not adequate to achieve the
true performance of the AD9235. This is especially true in IF
undersampling applications where frequencies in the 70 MHz to
100 MHz range are being sampled. For these applications,
Rev. D | Page 16 of 40
Data Sheet
AD9235
325
300
275
250
225
200
175
150
125
100
75
High speed, high resolution ADCs are sensitive to the quality of
the clock input. The degradation in SNR at a given full-scale
input frequency (fINPUT) due only to aperture jitter (tJ) can be
calculated by
AD9235-65
SNR Degradation = −20 × log10[2π × fINPUT × tJ]
In the equation, the rms aperture jitter, tJ, represents the root-
sum square of all jitter sources, which include the clock input,
analog input signal, and ADC aperture jitter specification.
Undersampling applications are particularly sensitive to jitter.
AD9235-40
AD9235-20
10
The clock input should be treated as an analog signal in cases
where aperture jitter may affect the dynamic range of the
AD9235. Power supplies for clock drivers should be separated
from the ADC output driver supplies to avoid modulating the
clock signal with digital noise. Low jitter, crystal-controlled
oscillators make the best clock sources. If the clock is generated
from another type of source (by gating, dividing, or other
methods), it should be retimed by the original clock at the last
step.
50
0
20
30
40
50
60
SAMPLE RATE (MSPS)
Figure 38. Total Power vs. Sample Rate with fIN = 10 MHz
For the AD9235-20 speed grade, the digital power consumption
can represent as much as 10% of the total dissipation. Digital
power consumption can be minimized by reducing the capaci-
tive load presented to the output drivers. The data in Figure 38
was taken with a 5 pF load on each output driver.
POWER DISSIPATION AND STANDBY MODE
The analog circuitry is optimally biased so that each speed
grade provides excellent performance while affording reduced
power consumption. Each speed grade dissipates a baseline
power at low sample rates that increases linearly with the clock
frequency.
As shown in Figure 38, the power dissipated by the AD9235 is
proportional to its sample rate. The digital power dissipation
does not vary substantially between the three speed grades
because it is determined primarily by the strength of the digital
drivers and the load on each output bit. The maximum DRVDD
current can be calculated as
By asserting the PDWN pin high, the AD9235 is placed in
standby mode. In this state, the ADC typically dissipates 1 mW
if the CLK and analog inputs are static. During standby, the
output drivers are placed in a high impedance state. Reasserting
the PDWN pin low returns the AD9235 into its normal
operational mode.
IDRVDD = VDRVDD × CLOAD × fCLK × N
where N is the number of output bits, 12 in the case of the
AD9235. This maximum current occurs when every output bit
switches on every clock cycle, i.e., a full-scale square wave at the
Nyquist frequency, fCLK/2. In practice, the DRVDD current is
established by the average number of output bits switching,
which is determined by the encode rate and the characteristics
of the analog input signal.
Low power dissipation in standby mode is achieved by shutting
down the reference, reference buffer, and biasing networks. The
decoupling capacitors on REFT and REFB are discharged when
entering standby mode and then must be recharged when
returning to normal operation. As a result, the wake-up time is
related to the time spent in standby mode, and shorter standby
cycles result in proportionally shorter wake-up times. With the
recommended 0.1 µF and 10 µF decoupling capacitors on REFT
and REFB, it takes approximately 1 sec to fully discharge the
reference buffer decoupling capacitors and 3 ms to restore full
operation.
Rev. D | Page 17 of 40
AD9235
Data Sheet
Table 7. Reference Configuration Summary
Selected Mode
SENSE Voltage Internal Switch Position
Resulting VREF (V)
Resulting Differential Span (V p-p)
External Reference
AVDD
N/A
N/A
2 × External Reference
Internal Fixed Reference
Programmable Reference
Internal Fixed Reference
VREF
0.2 V to VREF
AGND to 0.2 V
SENSE
SENSE
Internal Divider
0.5
1.0
0.5 × (1 + R2/R1)
1.0
2 × VREF (See Figure 40)
2.0
SENSE pin. This puts the reference amplifier in a noninverting
mode with the VREF output defined as
DIGITAL OUTPUTS
The AD9235 output drivers can be configured to interface with
2.5 V or 3.3 V logic families by matching DRVDD to the digital
supply of the interfaced logic. The output drivers are sized to
provide sufficient output current to drive a wide variety of logic
families. However, large drive currents tend to cause current
glitches on the supplies that may affect converter performance.
Applications requiring the ADC to drive large capacitive loads
or large fan-outs may require external buffers or latches.
VREF = 0.5 × (1 + R2/R1)
VIN+
VIN–
REFT
0.1µF
+
ADC
CORE
0.1µF
REFB
0.1µF
10µF
As detailed in Table 8, the data format can be selected for either
offset binary or twos complement.
VREF
0.1µF
+
Timing
10µF
0.5V
SELECT
LOGIC
The AD9235 provides latched data outputs with a pipeline delay
of seven clock cycles. Data outputs are available one propaga-
tion delay (tPD) after the rising edge of the clock signal. Refer to
Figure 2 for a detailed timing diagram.
SENSE
The length of the output data lines and loads placed on them
should be minimized to reduce transients within the AD9235;
these transients can detract from the converter’s dynamic
performance.
AD9235
Figure 39. Internal Reference Configuration
In all reference configurations, REFT and REFB drive the A/D
conversion core and establish its input span. The input range of
the ADC always equals twice the voltage at the reference pin for
either an internal or an external reference.
The lowest typical conversion rate of the AD9235 is 1 MSPS. At
clock rates below 1 MSPS, dynamic performance may degrade.
VOLTAGE REFERENCE
VIN+
A stable and accurate 0.5 V voltage reference is built into the
AD9235. The input range can be adjusted by varying the refer-
ence voltage applied to the AD9235, using either the internal
reference or an externally applied reference voltage. The input
span of the ADC tracks reference voltage changes linearly.
VIN–
REFT
0.1µF
+
ADC
CORE
0.1µF
REFB
0.1µF
10µF
If the ADC is being driven differentially through a transformer,
the reference voltage can be used to bias the center tap
(common-mode voltage).
VREF
0.1µF
+
10µF
0.5V
R2
SELECT
LOGIC
Internal Reference Connection
A comparator within the AD9235 detects the potential at the
SENSE pin and configures the reference into one of four possi-
ble states, which are summarized in Table 7. If SENSE is
grounded, the reference amplifier switch is connected to the
internal resistor divider (see Figure 39), setting VREF to 1 V.
Connecting the SENSE pin to VREF switches the reference
amplifier output to the SENSE pin, completing the loop and
providing a 0.5 V reference output. If a resistor divider is
connected as shown in Figure 40, the switch is again set to the
SENSE
R1
AD9235
Figure 40. Programmable Reference Configuration
Rev. D | Page 18 of 40
Data Sheet
AD9235
External Reference Operation
OPERATIONAL MODE SELECTION
The use of an external reference may be necessary to enhance
the gain accuracy of the ADC or to improve thermal drift
characteristics. When multiple ADCs track one another, a single
reference (internal or external) may be necessary to reduce gain
matching errors to an acceptable level. A high precision external
reference may also be selected to provide lower gain and offset
temperature drift. Figure 41 shows the typical drift characteris-
tics of the internal reference in both 1 V and 0.5 V modes.
As discussed earlier, the AD9235 can output data in either offset
binary or twos complement format. There is also a provision for
enabling or disabling the clock DCS. The MODE pin is a multi-
level input that controls the data format and DCS state. The
input threshold values and corresponding mode selections are
outlined in Table 8.
Table 8. Mode Selection
MODE Voltage Data Format
Duty Cycle Stabilizer
Twos Complement Disabled
Twos Complement Enabled
1.2
AVDD
2/3 AVDD
1/3 AVDD
AGND (Default)
1.0
Offset Binary
Offset Binary
Enabled
Disabled
VREF = 1.0V
0.8
The MODE pin is internally pulled down to AGND by a 20 kΩ
resistor.
VREF = 0.5V
0.6
TSSOP EVALUATION BOARD
0.4
0.2
0
The AD9235 evaluation board provides the support circuitry
required to operate the ADC in its various modes and configu-
rations. The converter can be driven differentially, through an
AD8138 driver or a transformer, or single-ended. Separate pow-
er pins are provided to isolate the DUT from the support cir-
cuitry. Each input configuration can be selected by proper con-
nection of various jumpers (refer to the schematics). Figure 43
shows the typical bench characterization setup used to evaluate
the ac performance of the AD9235. It is critical that signal
sources with very low phase noise (<1 ps rms jitter) be used to
realize the ultimate performance of the converter. Proper filter-
ing of the input signal, to remove harmonics and lower the inte-
grated noise at the input, is also necessary to achieve the speci-
fied noise performance.
–40 –30 –20 –10
0
10 20 30 40 50 60 70 80
TEMPERATURE (°C)
Figure 41. Typical VREF Drift
When the SENSE pin is tied to AVDD, the internal reference is
disabled, allowing the use of an external reference. An internal
reference buffer loads the external reference with an equivalent
7 kΩ load. The internal buffer still generates the positive and
negative full-scale references, REFT and REFB, for the ADC
core. The input span is always twice the value of the reference
voltage; therefore, the external reference must be limited to a
maximum of 1 V.
The AUXCLK input should be selected in applications requiring
the lowest jitter and SNR performance, i.e., IF undersampling
characterization. It allows the user to apply a clock input signal
that is 4× the target sample rate of the AD9235. A low-jitter,
differential divide-by-4 counter, the MC100LVEL33D, provides
a 1× clock output that is subsequently returned back to the CLK
input via JP9. For example, a 260 MHz signal (sinusoid) is
divided down to a 65 MHz signal for clocking the ADC. Note
that R1 must be removed with the AUXCLK interface. Lower
jitter is often achieved with this interface since many RF signal
generators display improved phase noise at higher output
frequencies and the slew rate of the sinusoidal output signal is
4× that of a 1× signal of equal amplitude.
If the internal reference of the AD9235 is used to drive multiple
converters to improve gain matching, the loading of the refer-
ence by the other converters must be considered. Figure 42
depicts how the internal reference voltage is affected by loading.
0.05
0
–0.05
0.5V ERROR (%)
–0.10
1V ERROR (%)
Complete schematics and layout plots follow and demonstrate
the proper routing and grounding techniques that should be
applied at the system level.
–0.15
–0.20
–0.25
0
0.5
1.0
1.5
2.0
2.5
3.0
LOAD (mA)
Figure 42. VREF Accuracy vs. Load
Rev. D | Page 19 of 40
AD9235
Data Sheet
LFCSP EVALUATION BOARD
An alternative differential analog input path using an AD8351
op amp is included in the layout but is not populated in produc-
tion. Designers interested in evaluating the op amp with the
ADC should remove C15, R12, and R3 and populate the op amp
circuit. The passive network between the AD8351 outputs and
the AD9235 allows the user to optimize the frequency response
of the op amp for the application.
The typical bench setup used to evaluate the ac performance
of the AD9235 is similar to the TSSOP Evaluation Board
connections (refer to the schematics for connection details).
The AD9235 can be driven single-ended or differentially
through a transformer. Separate power pins are provided to
isolate the DUT from the support circuitry. Each input
configuration can be selected by proper connection of
various jumpers (refer to the schematics).
3V
3V
3V
3V
+
+
+
+
–
–
–
–
AVDD GND DUT GND DUT
DVDD
J1
S4
AVDD
DRVDD
HP8644, 2V p-p
SIGNAL SYNTHESIZER
BAND-PASS
FILTER
REFIN
10MHz
XFMR
INPUT
DATA
CAPTURE
AND
AD9235
TSSOP EVALUATION BOARD
PROCESSING
HP8644, 2V p-p
CLOCK
S1
REFOUT CLOCK SYNTHESIZER
DIVIDER
CLOCK
Figure 43. TSSOP Evaluation Board Connections
Rev. D | Page 20 of 40
Data Sheet
AD9235
RP3 22Ω
RP5 22Ω
1
8
1
8
D0O
D1O
D2O
D3O
D0
D1
D2
D3
D8O
D9O
D8
RP3 22Ω
RP5 22Ω
2
7
2
7
D9
RP3 22Ω
RP5 22Ω
3
6
3
6
D10O
D11O
D10
D11
RP3 22Ω
RP5 22Ω
4
5
4
5
RP4 22Ω
RP6 22Ω
1
8
1
8
D4O
D5O
D6O
D7O
D4
D5
D6
RP4 22Ω
RP6 22Ω
2
7
2
7
RP4 22Ω
RP6 22Ω
3
6
3
6
WHT
TP5
JP23
JP22
RP4 22Ω
RP6 22Ω
DUTAVDD
C36
4
5
4
5
D7 OTRO
OTR
R3
10kΩ
C57
0.1µF
C22
10µF
10V
+
JP25
JP24
TP2
RED
0.1µF
FBEAD
L1
C39
0.001µF
DUTAVDDIN
TB1
JP12
DUTAVDD
2
1
2
3
+
R4
10kΩ
C21
10µF
10V
C58
22µF
25V
AD9235
+
C59
0.1µF
C35
0.1µF
7
8
1
WHT
TP17
AVDD
OTR
D11
D10
D9
OTRO
AGND
TB1
28
27
26
25
22
21
20
19
18
17
16
15
13
AGND
SENSE
VREF
PDWN
REFB
REFT
MODE
VIN+
D0O
3
D1O
4
D2O
C34
0.1µF
14
5
TP1
RED
D8
D3O
D7
D4O
FBEAD
L2
AVDDIN
TB1
6
AVDD
D6
D5O
C20
10µF
10V
C33
0.1µF
2
1
1
+
2
D5
D6O
C47
22µF
25V
SHEET 3
C50
0.1µF
+
C52
0.1µF
9
VIN+
VIN–
D4
D7O
U1
C32
0.1µF
10
11
12
23
24
VIN–
D3
D8O
AGND
AVDD
DGND
DRVDD
D2
D9O
JP13
AVDD
D1
D10O
D11O
DUTCLK
AVDD
D0
R27
5kΩ
R20
1kΩ
JP7
JP6
JP1
JP2
TP3
RED
CLK
FBEAD
L3
WHT
TP6
DRVDDIN
TB1
JP11
DUTDRVDD
2
1
5
4
R17
1kΩ
DUTAVDD
C23
DUTDRVDD
C48
22µF
25V
+
C53
0.1µF
C1
10µF
10V
AGND
TB1
+
+
C38
C41
0.001µF
C37
0.1µF
C40
0.001µF
R42
1kΩ
10µF
0.1µF
10V
TP4
RED
TP9
BLK
TP10
BLK
TP15
BLK
TP16
BLK
FBEAD
L4
DVDDIN
TB1
DVDD
2
1
6
C6
22µF
25V
+
TP11
BLK
TP12
BLK
TP13
BLK
TP14
BLK
C14
0.1µF
Figure 44. TSSOP Evaluation Board Schematic, DUT
Rev. D | Page 21 of 40
AD9235
Data Sheet
DVDD
C12
0.1µF
C4
R25
10kΩ
10µF
10V
2
AUXCLK
+
1
3
2
AVDD
1
S5
1
1
2
20
10
18
17
16
15
14
13
12
11
4
6
5
4
1
2
3
T1–1T
T2
G1
G2
A1
A2
A3
A4
A5
A6
A7
A8
VCC
GND
Y1
19
1N5712
1N5712
5
6
D2
D1
R11
49.9Ω
RP2 22Ω
RP2 22Ω
RP2 22Ω
RP2 22Ω
RP2 22Ω
RP2 22Ω
RP2 22Ω
RP2 22Ω
RP2 22Ω
RP2 22Ω
RP2 22Ω
RP2 22Ω
RP2 22Ω
RP2 22Ω
RP2 22Ω
RP2 22Ω
DD0
DD1
DD2
DD3
DD4
DD5
DD6
DD7
DD8
DD9
DD10
DD11
DOTR
2
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
7
8
D0
3
4
5
6
7
9
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
D1
D2
D3
D4
D5
D6
D7
Y2
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
Y3
MC100LVEL33D
U3
U6
74VHC541
R26
10kΩ
8
7
6
5
1
2
Y4
Y5
Y6
Y7
Y8
AVDD
VCC
OUT
REF
VEE
NC
INA
INB
3
4
INCOM
AVDD
9
AVDD
AVDD
C28
10µ
10V
16
15
14
13
12
11
10
9
+
C24
0.1µF
F
C11
0.1µF
R12
113Ω
R13
113Ω
C27
0.1µF
U8 DECOUPLING
C26
0.1µF
C5
10µF
10V
2
R14
90Ω
R15
90Ω
+
1
1
20
10
18
17
16
15
14
13
12
11
DACLK
G1
G2
A1
A2
A3
A4
A5
A6
A7
A8
VCC
GND
Y1
19
JP9
2
D8
D9
3
4
5
6
7
Y2
R19
500Ω
R2
10Ω
R18
500Ω
HDR40RAM
J1
D10
D11
Y3
AVDD; 14
AVDD; 7
U7
74VHC541
AVDD
CW
C13
Y4
Y5
Y6
Y7
Y8
CLOCK
R7
WHT
TP7
1
S1
U8
U8
0.1µF
22Ω DUTCLK
1
OTR
2
5
6
2
R1
49.9Ω
74VHC04 74VHC04
JP4
JP3
9
R9
22Ω
U8
3
13
11
9
4
74VHC04
U8
AVDD
12
C8
C10
74VHC04
10µF
10V
0.1µF
U8
U9 DECOUPLING
10
U8
8
74VHC04
Figure 45. TSSOP Evaluation Board Schematic, Clock Inputs and Output Buffering
Rev. D | Page 22 of 40
Data Sheet
AD9235
AVDD
C7
R23
1kΩ
0.1µF
JP5
SINGLE INPUT
1
S3
2
C9
0.33µF
R5
49.9Ω
JP42
JP40
JP45
R41
1kΩ
C15
10µF
10V
AVDD
C44
15pF
AVDD
R21
22Ω
1
2
C69
VIN+
0.1µF
R32
1kΩ
C44B
C2
VAL
R22
JP46
JP41
JP43
22Ω
R33
1kΩ
C8
0.1µF
VIN–
R37
499Ω
C42
VAL
C43
15pF
R6
40Ω
R34
523Ω
VCC
3
–IN
1
8
4
VO+
AD8138
R35
499Ω
2
AMP INPUT
1
VOC
R10
40Ω
U2
5
S2
VO–
2
+IN
R31
49.9Ω
6
VEE
C45
VAL
C18
0.1µF
R36
499Ω
AVDD
R16
XFMR INPUT
1
C19
6
5
4
1
2
3
C17
VAL
T1–1T
T2
1kΩ
10µF
10V
2
S4
2
+
1
ALT VEE
R24
49.9Ω
TP8
RED
3
2
A
B
R8
1kΩ
C25
0.33µF
C16
0.1µF
1
JP8
Figure 46. TSSOP Evaluation Board Schematic, Analog Inputs
DACLK
AD9762
U4
1
2
28
27
26
25
24
23
22
21
20
19
18
17
16
15
DD0
DD1
DD2
DD3
DD4
DD5
DD6
DD7
DD8
DD9
DD10
DD11
MSB-DB11 CLOCK
DVDD
C30
0.1µF
C31
0.01µF
DB10
DB19
DB8
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
NC1
NC2
DVDD
DCOM
NC3
3
C29
0.1µF
C46
0.01µF
4
5
AVDD
WHT
TP18
6
COMP2
IOUTA
IOUTB
ACOM
COMP1
FSADJ
REFIO
REFLO
SLEEP
S6
7
R29
49.9Ω
8
C56
0.1µF
9
C55
22pF
10
11
12
13
14
R28
49.9Ω
C51
0.1µF
C49
0.1µF 2kΩ
R30
C54
22pF
Figure 47. TSSOP Evaluation Board Schematic, Optional DAC
Rev. D | Page 23 of 40
AD9235
Data Sheet
Figure 48. TSSOP Evaluation Board Layout, Primary Side
Rev. D | Page 24 of 40
Data Sheet
AD9235
Figure 49. TSSOP Evaluation Board Layout, Secondary Side
Rev. D | Page 25 of 40
AD9235
Data Sheet
Figure 50. TSSOP Evaluation Board Layout, Ground Plane
Rev. D | Page 26 of 40
Data Sheet
AD9235
_
Figure 51. TSSOP Evaluation Board Power Plane
Rev. D | Page 27 of 40
AD9235
Data Sheet
Figure 52. TSSOP Evaluation Board Layout, Primary Silkscreen
Rev. D | Page 28 of 40
Data Sheet
AD9235
Figure 53. TSSOP Evaluation Board Layout, Secondary Silkscreen
Rev. D | Page 29 of 40
AD9235
Data Sheet
EXTREF
1V MAX E1
GND AVDD
C13
C22
R1
0.10µF
10µF
10kΩ
P9 P8 P11
P7
A
B
C
D
R9
10kΩ
C12
0.1µF
GND
GND
E
AVDD
H1
MTHOLE6
P10
1
GND
P2
P6
R5
1kΩ
GND GND
1
2
3
4
5
6
H2
MTHOLE6
MODE
P5
H3
MTHOLE6
C29
10µF
2 2
C9
0.10µF
C11
0.1µF
P1
R7
1kΩ
C8
0.1µF
+
H4
MTHOLE6
GND
3
C7
0.1µF
GND
P3
R6
1kΩ
OVERRANGE BIT
(MSB)
GND
GND
4
P4
1
2
3
4
5
6
7
8
16
DRX
15
24 23 22 21 20 19 18 17
D13X
14
D12X
13
C6
0.1µF
R42
0Ω
D11X
12
D10X
11
25
26
27
28
29
30
31
32
16
15
14
13
12
11
10
9
REFB
REFT
AVDD
AGND
VIN+
DRVDD
DGND
D7
D9X
10
AVDD
DRVDD
GND
D8X
9
AMPIN
GND
R36
1kΩ
R26
1kΩ
D7X
AVDD
RP2 220Ω
GND
VIN+
AD9235
D6
X
OUT
U4
D5
R12
0Ω
R4
33kΩ
C21
10pF
VIN–
T1
ADT 1–1 WT
VIN–
D4
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
C15
0.1µF
D6X
D5X
D4X
D3X
D2X
D1X
D0X
R10
36Ω
E 45
GND
AGND
AVDD
D3
J1
C26
10pF
XFRIN1
NC
GND
1
5
3
6
2
4
AVDD
D2
L1
10nH
CT
R2
XX
C19
(LSB)
C16
AMP
C5
0.1µF
GND
GND
1
2
3
4
5
6
7
8
OR L1
0.1µF
PRI SEC
GND
15pF
FOR FILTER
GND
GND
RP1 220Ω
CLK
P14
R11
36Ω
OPTIONAL XFR
T2
FT C1–1–13
R3
0Ω
R8
1kΩ
GND
C23
X
B
OUT
10pF
1
5
2
4
P13
AMPINB
X FRIN
X
OUT
AVDD
GND
R15
CT
X
33Ω
3
B
C18
OUT
SENSE PIN SOLDERABLE JUMPER
AVDD
PRI SEC
GND
0.1µF
R13
1kΩ
R25
1kΩ
GND
E TO A
E TO B
E TO C
E TO D
EXTERNAL VOLTAGE DIVIDER
R18
25Ω
INTERNAL 1V REFERENCE (DEFAULT)
EXTERNAL REFERENCE
R SINGLE ENDED
R3, R17, R18
ONLY ONE SHOULD BE
ON BOARD AT A TIME
INTERNAL 0.5V REFERENCE
GND
MODE PIN SOLDERABLE JUMPER
5 TO 1 TWOS COMPLEMENT/DCS OFF
5 TO 2 TWOS COMPLEMENT/DCS OFF
5 TO 3 OFFSET BINARY/DCS ON
5 TO 4 OFFSET BINARY/DCS OFF
Figure 54. LFCSP Evaluation Board Schematic, Analog Inputs and DUT
Rev. D | Page 30 of 40
Data Sheet
AD9235
74LVTH162374
U1
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
2CLK
2OE
2QB
2Q7
GND
2Q6
2Q5
CLKAT/DAC
MSB DRX
D13X
GND
GND
HEADER 40
2DB
2D7
GND
2D6
2D5
DRY
2
4
6
1
3
5
7
9
2
1
3
GND
4
DR
GND
6
5
D12X
D11X
MSB GND
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
8
7
V
V
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
9
DRVDD
D10X
DRVDD
CC
CC
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
2D4
2D3
GND
2D2
2D1
1D8
1D7
GND
1D6
1D5
2Q4
2Q3
GND
2Q2
2Q1
1Q8
1Q7
GND
1Q6
1Q5
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
D9X
GND
GND
GND
D8X
D7X
D6X
D5X
GND
D4X
D3X
8
7
V
V
DRVDD
D2X
DRVDD
CC
CC
6
1D4
1Q4
1Q3
GND
1Q2
1Q1
1OE
5
1D3
D1X
DRY
4
GND
1D2
GND
LSB
GND
GND
3
D0X
2
1D1
GND
GND
1
1CLK
1
CLKLAT/DAC
IN
OUT
R38
R39
1kΩ
1kΩ
VAMP
GND
C44
0.1µF
C24
10µF
VAMP
POWER DOWN
USE R40 OR R41
+
C45
0.1µF
GND
GND
GND
VAMP
GND
R41
R40
AD8351
R41
10kΩ
R14
25Ω
10kΩ 10kΩ
U3
PWDN
RGP1
INHI
VOCM
1
2
3
4
5
10
9
VPOS
OPH1
OPLO
COMM
C28
0.1µF
C27
R16
0Ω
AMP IN
AMP
0.1µF
8
AMPINB
AMPIN
INLO
RPG2
7
R17
0Ω
C35
0.10µF
C17
R19
50Ω
R35
25Ω
6
0.1µF
R33
25Ω
GND
R34
1.2kΩ
GND GND
Figure 55. LFCSP Evaluation Board Schematic, Digital Path
Rev. D | Page 31 of 40
AD9235
Data Sheet
Figure 56. LFCSP Evaluation Board Schematic, Clock Input
Rev. D | Page 32 of 40
Data Sheet
AD9235
Figure 59. LFCSP Evaluation Board Layout, Ground Plane
Figure 57. LFCSP Evaluation Board Layout, Primary Side
Figure 58. LFCSP Evaluation Board Layout, Secondary Side
Figure 60. LFCSP Evaluation Board Layout, Power Plane
Rev. D | Page 33 of 40
AD9235
Data Sheet
Figure 61. LFCSP Evaluation Board Layout, Primary Silkscreen
Figure 62. LFCSP Evaluation Board Layout, Secondary Silkscreen
Rev. D | Page 34 of 40
Data Sheet
AD9235
Table 9. LFCSP Evaluation Board Bill of Materials (BOM)
Recommended Vendor/ Supplied
Item Qty. Omit1 Reference Designator
Device
Package Value Part Number
by ADI
1
18
C1, C5, C7, C8, C9, C11,
C12, C13, C15, C16, C31, C33,
C34, C36, C37, C41, C43, C47
Chip Capacitor
0603
0.1 µF
8
2
C6, C18, C27, C17,
C28, C35, C45, C44
2
3
8
8
C2, C3, C4, C10, C20,
C22, C25, C29
Tantalum Capacitor
Chip Capacitor
TAJD
0603
10 µF
C46, C24
C14, C30, C32, C38,
C39, C40, C48, C49
0.001 µF
4
5
6
3
1
9
C19, C21, C23
C26
Chip Capacitor
Chip Capacitor
Header
0603
10 pF
10 pF
0603
E31, E35, E43, E44,
E50, E51, E52, E53
EHOLE
Jumper Blocks
2
1
E1, E45
J1, J2
L1
7
8
2
1
SMA Connector/50 Ω
Inductor
SMA
0603
10 nH Coilcraft/
0603CS-10NXGBU
9
P2
Terminal Block
TB6
Wieland/25.602.2653.0,
z5-530-0625-0
10
11
1
5
P12
Header Dual 20-Pin RT Angle HEADER40
Digi-Key S2131-20-ND
R3, R12, R23, R28, RX
R37, R22, R42, R16, R17, R27
R4, R15
Chip Resistor
0603
0 Ω
6
1
12
13
2
Chip Resistor
Chip Resistor
0603
0603
33 Ω
1 k Ω
14
R5, R6, R7, R8, R13, R20,
R21, R24, R25, R26,
R30, R31, R32, R36
14
15
2
1
R10, R11
R29
Chip Resistor
Chip Resistor
0603
0603
36 Ω
50 Ω
R19
16
2
RP1, RP2
Resistor Pack
ADT1-1WT
R_742
220 Ω Digi-Key
CTS/742C163220JTR
17
18
1
1
T1
AWT1-1T
TSSOP-48
Mini-Circuits
U1
74LVTH162374
CMOS Register
19
20
21
22
23
24
25
26
27
28
1
1
1
U4
AD9235BCP ADC (DUT)
74VCX86M
LFCSP-32
SOIC-14
PCB
Analog Devices, Inc.
Fairchild
X
U5
PCB
AD92XXBCP/PCB
AD8351 Op Amp
MACOM Transformer
Chip Resistor
Analog Devices, Inc.
Analog Devices, Inc.
X
X
1
U3
MSOP-8
1
T2
ETC1-1-13 1-1 TX M/A-COM/ETC1-1-13
5
R9, R1, R2, R38, R39
R18, R14, R35
R40, R41
0603
0603
0603
SELECT
25 Ω
3
Chip Resistor
2
Chip Resistor
10 k Ω
1.2 k Ω
100 Ω
1
R34
Chip Resistor
1
R33
Chip Resistor
Total 82
34
1 These items are included in the PCB design but are omitted at assembly.
Rev. D | Page 35 of 40
AD9235
Data Sheet
OUTLINE DIMENSIONS
9.80
9.70
9.60
28
15
4.50
4.40
4.30
6.40 BSC
1
14
PIN 1
0.65
BSC
1.20 MAX
0.15
0.05
8°
0°
0.75
0.60
0.45
0.30
0.19
0.20
0.09
SEATING
PLANE
COPLANARITY
0.10
COMPLIANT TO JEDEC STANDARDS MO-153-AE
Figure 63. 28-Lead Thin Shrink Small Outline Package [TSSOP]
(RU-28)
Dimensions shown in millimeters
5.10
5.00 SQ
4.90
0.30
0.25
0.18
PIN 1
INDICATOR
PIN 1
25
24
32
1
INDICATOR
0.50
BSC
3.25
3.10 SQ
2.95
EXPOSED
PAD
17
16
8
9
0.50
0.40
0.30
0.25 MIN
TOP VIEW
BOTTOM VIEW
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
0.80
0.75
0.70
0.05 MAX
0.02 NOM
SECTION OF THIS DATA SHEET.
COPLANARITY
0.08
0.20 REF
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-220-WHHD.
Figure 64. 32-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
5 × 5 mm Body, Very Very Thin Quad
(CP-32-7)
Dimensions shown in millimeters
Rev. D | Page 36 of 40
Data Sheet
AD9235
ORDERING GUIDE
Model1, 2
Temperature Range
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
Package Description
Package Option
AD9235BRU-20
28-Lead Thin Shrink Small Outline Package (TSSOP)
28-Lead Thin Shrink Small Outline Package (TSSOP)
28-Lead Thin Shrink Small Outline Package (TSSOP)
28-Lead Thin Shrink Small Outline Package (TSSOP)
28-Lead Thin Shrink Small Outline Package (TSSOP)
28-Lead Thin Shrink Small Outline Package (TSSOP)
28-Lead Thin Shrink Small Outline Package (TSSOP)
28-Lead Thin Shrink Small Outline Package (TSSOP)
28-Lead Thin Shrink Small Outline Package (TSSOP)
28-Lead Thin Shrink Small Outline Package (TSSOP)
28-Lead Thin Shrink Small Outline Package (TSSOP)
28-Lead Thin Shrink Small Outline Package (TSSOP)
32-Lead Lead Frame Chip Scale Package (LFCSP_WQ)
32-Lead Lead Frame Chip Scale Package (LFCSP_WQ)
32-Lead Lead Frame Chip Scale Package (LFCSP_WQ)
32-Lead Lead Frame Chip Scale Package (LFCSP_WQ)
32-Lead Lead Frame Chip Scale Package (LFCSP_WQ)
32-Lead Lead Frame Chip Scale Package (LFCSP_WQ)
RU-28
RU-28
RU-28
RU-28
RU-28
RU-28
RU-28
RU-28
RU-28
RU-28
RU-28
RU-28
CP-32-7
CP-32-7
CP-32-7
CP-32-7
CP-32-7
CP-32-7
AD9235BRURL7-20
AD9235BRUZ-20
AD9235BRUZRL7-20
AD9235BRU-40
AD9235BRURL7-40
AD9235BRUZ-40
AD9235BRUZRL7-40
AD9235BRU-65
AD9235BRURL7-65
AD9235BRUZ-65
AD9235BRUZRL7-65
AD9235BCPZ-20
AD9235BCPZRL7-20
AD9235BCPZ-40
AD9235BCPZRL7-40
AD9235BCPZ-65
AD9235BCPZRL7-65
1 Z = RoHS Compliant Part.
2 It is recommended that the exposed paddle be soldered to the ground plane. There is an increased reliability of the solder joints and maximum thermal capability of
the package is achieved with exposed paddle soldered to the customer board.
Rev. D | Page 37 of 40
AD9235
NOTES
Data Sheet
Rev. D | Page 38 of 40
Data Sheet
NOTES
AD9235
Rev. D | Page 39 of 40
AD9235
NOTES
Data Sheet
©2012 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D02461-0-10/12(D)
Rev. D | Page 40 of 40
相关型号:
©2020 ICPDF网 联系我们和版权申明