AD9652BBCZRL7-310 [ADI]
Analog-to-Digital Converter (ADC);型号: | AD9652BBCZRL7-310 |
厂家: | ADI |
描述: | Analog-to-Digital Converter (ADC) |
文件: | 总37页 (文件大小:1475K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
16-Bit, 310 MSPS, 3.3 V/1.8 V Dual
Analog-to-Digital Converter (ADC)
Data Sheet
AD9652
FEATURES
High dynamic range
FUNCTIONAL BLOCK DIAGRAM
AVDD3
AVDD
SDIO SCLK CSB
DRVDD
SNR = 75.0 dBFS at 70 MHz (AIN = −1 dBFS)
SFDR = 87 dBc at 70 MHz (AIN = −1 dBFS)
Noise spectral density (NSD) = −156.7 dBFS/Hz input noise
at −1 dBFS at 70 MHz
SPI
AD9652
OR+, OR–
PROGRAMMING DATA
NSD = −157.6 dBFS/Hz for small signal at −7dBFS at 70 MHz
90 dB channel isolation/crosstalk
On-chip dithering (improves small signal linearity)
Excellent IF sampling performance
SNR = 73.7 dBFS at 170 MHz (AIN = −1 dBFS)
SFDR = 85 dBc at 170 MHz (AIN = −1 dBFS)
Full power bandwidth of 465 MHz
VIN+A
VIN–A
DDR DATA
INTERLEAVER
LVDS OUTPUT
DRIVER
D15± (MSB)
TO
16
ADC
D0± (LSB)*
VREF
CLK+
CLK–
DIVIDE 1
TO 8
SENSE
DCO+
DCO–
REF
SELECT
DUTY CYCLE
DCO
STABILIZER GENERATION
VCM
RBIAS
VIN–B
VIN+B
On-chip 3.3 V buffer
Programmable input span of 2 V p-p to 2.5 V p-p (default)
Differential clock input receiver with 1, 2, 4, and 8 integer
inputs (clock divider input accepts up to 1.24 GHz)
Internal ADC clock duty cycle stabilizer
SYNC input allows multichip synchronization
Total power consumption: 2.16 W
3.3 V and 1.8 V supply voltages
DDR LVDS (ANSI-644 levels) outputs
Serial port control
ADC
MULTICHIP
SYNC
AGND
SYNC
PDWN
*THESE PINS ARE FOR CHANNEL A AND CHANNEL B.
Figure 1.
Energy saving power-down modes
APPLICATIONS
Military radar and communications
Multimode digital receivers (3G or 4G)
Test and instrumentation
Smart antenna systems
The 16-bit output data (with an overrange bit) from each ADC
is interleaved onto a single LVDS output port along with a
double data rate (DDR) clock. Programming for setup and control
are accomplished using a 3-wire SPI-compatible serial interface.
GENERAL DESCRIPTION
The AD9652 is a dual, 16-bit analog-to-digital converter (ADC)
with sampling speeds of up to 310 MSPS. It is designed to
support demanding, high speed signal processing applications
that require exceptional dynamic range over a wide input
frequency range (up to 465 MHz). Its exceptional low noise
floor of −157.6 dBFS and large signal spurious-free dynamic
range (SFDR) performance (exceeding 85 dBFS, typical) allows
low level signals to be resolved in the presence of large signals.
The AD9652 is available in a 144-ball CSP_BGA and is
specified over the industrial temperature range of −40°C to
+85°C. This product is protected by pending U.S. patents.
PRODUCT HIGHLIGHTS
1. Integrated dual, 16-bit, 310 MSPS ADCs.
2. On-chip buffer simplifies ADC driver interface.
3. Operation from 3.3 V and 1.8 V supplies and a separate
digital output driver supply accommodating LVDS outputs.
4. Proprietary differential input maintains excellent signal-to-
noise ratio (SNR) performance for input frequencies of up
to 485 MHz.
5. SYNC input allows synchronization of multiple devices.
6. Three-wire, 3.3 V or 1.8 V SPI port for register programming
and readback.
The dual ADC cores feature a multistage, pipelined architecture
with integrated output error correction logic. A high performance
on-chip buffer and internal voltage reference simplify the inter-
face to external driving circuitry while preserving the exceptional
performance of the ADC.
The AD9652 can support input clock frequencies of up to
1.24 GHz with a 1, 2, 4, and 8 integer clock divider to generate
the ADC sample clock. A duty cycle stabilizer is provided to
compensate for variations in the ADC clock duty cycle.
Rev. B
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2014–2017 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
AD9652* PRODUCT PAGE QUICK LINKS
Last Content Update: 02/23/2017
COMPARABLE PARTS
View a parametric search of comparable parts.
DESIGN RESOURCES
• ad9652 Material Declaration
• PCN-PDN Information
• Quality And Reliability
• Symbols and Footprints
EVALUATION KITS
• AD-FMCOMMS6-EBZ Evaluation Board
• AD9652 Evaluation Board
DISCUSSIONS
View all ad9652 EngineerZone Discussions.
DOCUMENTATION
Data Sheet
SAMPLE AND BUY
Visit the product page to see pricing options.
• AD9652: 16-Bit, 310 MSPS, 3.3 V/1.8 V Dual Analog-to-
Digital Converter (ADC) Data Sheet
REFERENCE MATERIALS
Press
TECHNICAL SUPPORT
Submit a technical question or find your regional support
number.
• Analog Devices Unveils a 16-Bit, 310 MSPS, Dual A/D
Converter Providing Industry-leading Noise and Linearity
Performance Over a Wide Input Range
DOCUMENT FEEDBACK
Submit feedback for this data sheet.
This page is dynamically generated by Analog Devices, Inc., and inserted into this data sheet. A dynamic change to the content on this page will not
trigger a change to either the revision number or the content of the product data sheet. This dynamic page may be frequently modified.
AD9652
Data Sheet
TABLE OF CONTENTS
Features.....................................................................................1
Voltage Reference................................................................23
Clock Input Considerations.................................................23
Power Dissipation and Standby Mode .................................25
Internal Background Calibration.........................................25
Digital Outputs....................................................................26
ADC Overrange...................................................................26
Fast Threshold Detection (FDA/FDB).....................................28
Serial Port Interface.................................................................29
Configuration Using the SPI................................................29
Hardware Interface..............................................................29
Configuration Without the SPI............................................29
SPI Accessible Features........................................................30
Memory Map...........................................................................31
Reading the Memory Map Register Table............................31
Memory Map Register Table................................................32
Applications Information........................................................35
Design Guidelines................................................................35
Outline Dimensions ................................................................36
Ordering Guide ...................................................................36
Applications...............................................................................1
Functional Block Diagram.........................................................1
General Description ..................................................................1
Product Highlights ....................................................................1
Revision History........................................................................2
Specifications.............................................................................3
ADC DC Specifications .........................................................3
ADC AC Specifications..........................................................4
Digital Specifications .............................................................5
Switching Specifications.........................................................7
Timing Specifications ............................................................7
Absolute Maximum Ratings......................................................9
Thermal Characteristics.........................................................9
ESD Caution..........................................................................9
Pin Configuration and Function Descriptions.........................10
Typical Performance Characteristics .......................................13
Equivalent Circuits..................................................................19
Theory of Operation................................................................20
ADC Architecture................................................................20
Analog Input Considerations...............................................20
REVISION HISTORY
1/2017—Rev. A to Rev. B
Changes to DCO to Data Skew(tSKEW) Parameter, Table 4 ...........7
Changes to Clock Input Options Section.................................24
5/2014—Rev. 0 to Rev. A
Changes to Supply Current, Clock Divider = 1 Parameter and
Power Consumption, Clock Divider = 1 Parameter, Table 1......3
4/2014—Revision0: Initial Version
Rev. B | Page 2 of 36
Data Sheet
AD9652
SPECIFICATIONS
ADC DC SPECIFICATIONS
AVD D 3 = 3.3 V, AVD D = AVDD_CLK = 1.8 V, SPIVDD = DRVDD = 1.8 V, sample rate = 310 MSPS (clock input = 1240 MHz, AD9652
divided by 4), VIN = −1.0 dBFS differential input, 2.5 V p-p full-scale input range, duty cycle stabilizer (DCS) enabled, dither disabled,
unless otherwise noted.
Table 1.
Parameter
Temperature
Min
Typ
Max
Unit
RESOLUTION
Full
16
Bits
ACCURACY
No Missing Codes
Offset Error
Full
Full
Full
Full
Full
Guaranteed
1.5
mV
Gain Error
−0.3
−0.76/+1.1
−4.5/+4.5
% FSR
LSB
LSB
Differential Nonlinearity (DNL)1
Integral Nonlinearity (INL)1
MATCHING CHARACTERISTIC
Offset Error
Full
Full
0.7
0.1
mV
%FSR
Gain Error
TEMPERATURE DRIFT
Offset Error
Full
Full
0.8
16
ppm/°C
ppm/°C
Gain Error
INPUT REFERRED NOISE
VREF = 1.25 V
25°C
3.7
LSB rms
ANALOG INPUT
Input Span (for VREF = 1.25 V)
Input Capacitance2
Input Resistance3
Input Common-Mode Voltage
POWER SUPPLIES
Supply Voltage
AVDD3
Full
Full
Full
Full
2.5
5.8
27
V p-p
pF
kΩ
V
2.0
2.4
Full
Full
Full
Full
Full
3.15
1.7
1.7
1.7
1.7
3.3
1.8
1.8
1.8
1.8
3.45
1.9
1.9
1.9
3.6
V
V
V
V
V
AVDD
AVDD_CLK
DRVDD
SPIVDD
Supply Current, Clock Divider = 1
IAVDD3
IAVDD
Full
Full
Full
Full
Full
145
701
56
180
0.005
mA
mA
mA
mA
mA
IAVDD_CLK
IDRVDD
ISPIVDD
POWER CONSUMPTION
Clock Divider = 1
Normal Operation1
Standby Power4
Power-Down Power
Full
Full
Full
2160
80
2236
mW
mW
mW
1
1 Measured with a low input frequency, full-scale sine wave.
2 Input capacitance refers to the effective capacitance between one differential input pin and AGND.
3 Input resistance refers to the effective resistance between one differential input pin and AGND.
4 Standby power is measured with adc input and the CLK pins inactive (that is, set to AVDD or AGND).
Rev. B | Page 3 of 36
AD9652
Data Sheet
ADC AC SPECIFICATIONS
AVD D 3 = 3.3 V, AVDD = AVDD_CLK = 1.8 V, SPIVDD = DRVDD = 1.8 V, sample rate = 310 MSPS (clock input = 1240 MHz, AD9652
divided by 4), VIN = −1.0 dBFS differential input, 2.5 V p-p full-scale input range, DCS enabled, dither disabled, unless otherwise noted.
Table 2.
VREF = 1 V
Typ
VREF = 1.25 V, Default
Parameter1
Temperature
Min
Max
Min
Typ
Max
Unit
DIFFERENTIAL INPUT VOLTAGE
SIGNAL-TO-NOISE RATIO (SNR)
fIN = 30 MHz (Use Nyquist 1 Settings)
fIN = 70 MHz (Use Nyquist 1 Settings)
25°C
2.0
2.5
V p-p
25°C
25°C
Full
74.0
73.6
75.4
75.0
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
74.0
73.3
fIN = 70 MHz (Use Nyquist 1 Settings, with Dither Enabled)
fIN = 170 MHz (Use Nyquist 2 Settings)
fIN = 170 MHz (Use Nyquist 2 Settings, with Dither Enabled)
fIN = 305 MHz (Use Nyquist 2 Settings)
25°C
25°C
25°C
25°C
25°C
73.1
72.1
71.2
70.1
67.9
74.3
73.7
72.0
70.7
68.0
fIN = 400 MHz (Use Nyquist 3 Settings)
SIGNAL-TO-NOISE AND DISTORTION (SINAD)
fIN = 30 MHz (Use Nyquist 1 Settings)
fIN = 70 MHz (Use Nyquist 1 Settings)
25°C
25°C
Full
72.8
73.5
74.2
74.6
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
73.8
73.2
fIN = 70 MHz (Use Nyquist 1 Settings, with Dither Enabled)
fIN = 170 MHz (Use Nyquist 2 Settings)
fIN = 170 MHz (Use Nyquist 2 Settings, with Dither Enabled)
fIN = 305 MHz (Use Nyquist 2 Settings)
25°C
25°C
25°C
25°C
25°C
73.0
72.0
71.1
74.0
72.6
71.7
68.5
65.8
fIN = 400 MHz (Use Nyquist 3 Settings)
EFFECTIVE NUMBER OF BITS (ENOB)
fIN = 30 MHz (Use Nyquist 1 Settings)
fIN = 70 MHz (Use Nyquist 1 Settings)
25°C
25°C
Full
11.8
12
12.0
12.1
Bits
Bits
Bits
Bits
Bits
Bits
Bits
Bits
12.0
11.9
fIN = 70 MHz (Use Nyquist 1 Settings, with Dither Enabled)
fIN = 170 MHz (Use Nyquist 2 Settings)
fIN = 170 MHz (Use Nyquist 2 Settings, with Dither Enabled)
fIN = 305 MHz (Use Nyquist 2 Settings)
25°C
25°C
25°C
25°C
25°C
11.8
11.7
11.5
12.0
11.8
11.6
11.1
10.6
fIN = 400 MHz (Use Nyquist 3 Settings)
WORST SECOND OR THIRD HARMONIC
fIN = 30 MHz (Use Nyquist 1 Settings)
fIN = 70 MHz (Use Nyquist 1 Settings)
25°C
25°C
Full
−96
−90
−94
−87
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
−83
−83
fIN = 70 MHz (Use Nyquist 1 Settings, with Dither Enabled)
fIN = 170 MHz (Use Nyquist 2 Settings)
25°C
25°C
25°C
25°C
25°C
−92
−87
−87
−89
−80
−89
−85
−85
−86
−77
fIN = 170 MHz (Use Nyquist 2 Settings, with Dither Enabled)
fIN = 305 MHz (Use Nyquist 2 Settings)
fIN = 400 MHz (Use Nyquist 3 Settings)
SPURIOUS-FREE DYNAMIC RANGE (SFDR)
fIN = 30 MHz (Use Nyquist 1 Settings)
fIN = 70 MHz (Use Nyquist 1 Settings)
25°C
25°C
Full
96
90
94
87
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
83
83
fIN = 70 MHz (Use Nyquist 1 Settings. with Dither Enabled)
fIN = 170 MHz (Use Nyquist 2 Settings)
25°C
25°C
25°C
25°C
25°C
92
84
87
89
80
89
85
85
86
77
fIN = 170 MHz (Use Nyquist 2 Settings, with Dither Enabled)
fIN = 305 MHz (Use Nyquist 2 Settings)
fIN = 400 MHz (Use Nyquist 3 Settings)
Rev. B | Page 4 of 36
Data Sheet
AD9652
VREF = 1 V
Typ
VREF = 1.25 V, Default
Parameter1
Temperature
Min
Max
Min
Typ
Max
Unit
WORST OTHER (NOT INCLUDING 2nd or 3rd HARMONIC)
fIN = 30 MHz (Use Nyquist 1 Settings)
fIN = 70 MHz (Use Nyquist 1 Settings)
25°C
25°C
Full
−101
−99
−102
−98
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
−90
−86
fIN = 70 MHz (Use Nyquist 1 Settings, with Dither Enabled)
fIN = 170 MHz (Use Nyquist 2 Settings)
fIN = 170 MHz (Use Nyquist 2 Settings, with Dither Enabled)
fIN = 305 MHz (Use Nyquist 2 Settings)
fIN = 400 MHz (Use Nyquist 3 Settings)
TWO-TONE SFDR
25°C
25°C
25°C
25°C
25°C
−100
−91
−90
−98
−92
−100
−90
−95
−97
−91
fIN = 70.1 MHz (−7 dBFS ), 72.1 MHz (−7 dBFS )
fIN = 184.12 MHz (−7 dBFS ), 187.12 MHz (−7 dBFS )
CROSSTALK2
25°C
25°C
Full
93
83
dBc
dBc
dB
90
90
FULL POWER BANDWIDTH3
NOISE BANDWIDTH4
25°C
25°C
485
650
485
650
MHz
MHz
1 See the AN-835 Application Note, UnderstandingHighSpeed ADC Testing and Evaluation, for a complete set of definitions.
2 Crosstalk is measured at 100 MHz with −1.0dBFS on one channel and no input on the alternate channel.
3 Full power bandwidth is the bandwidth of operation in which proper ADC performance can be achieved.
4 Noise bandwidth is the −3 dB bandwidth for the ADC inputs across which noise can enter the ADC and is not attenuated internally.
DIGITAL SPECIFICATIONS
AVD D 3 = 3.3 V, AVDD = AVDD_CLK = 1.8 V, SPIVDD = DRVDD = 1.8 V, sample rate = 310 MSPS (clock input = 1240 MHz, AD9652
divided by 4), VIN = −1.0 dBFS differential input, 2.5 V p-p full-scale input range, DCS enabled, dither disabled, unless otherwise noted.
Table 3.
Parameter
Test Conditions/Comments Temperature Min
Typ Max
Unit
DIFFERENTIAL CLOCK INPUTS (CLK+, CLK−)
Logic Compliance
Differential Input Voltage
CMOS/LVDS/LVPECL
3.6
Full
0.3
V p-
p
Input Voltage Range
Internal Common-Mode Bias
Input Common-Mode Range
High Level Input Current
Low Level Input Current
Input Capacitance1
Full
Full
Full
Full
Full
Full
Full
AGND
AVDD_CLK
V
V
V
µA
µA
pF
kΩ
0.9
0.9
+10
−155
1.4
+145
−15
5
10
Input Resistance1
SYNC INPUT
Logic Compliance
Internal Bias
CMOS/LVDS
0.9
Full
Full
Full
Full
Full
Full
Full
Full
V
V
Input Voltage Range
High Level Input Voltage
Low Level Input Voltage
High Level Input Current
Low Level Input Current
Input Capacitance
AGND
1.2
AGND
−15
AVDD_CLK
AVDD_CLK
0.6
+110
V
V
µA
µA
pF
kΩ
−105
+15
1.5
16
Input Resistance
Rev. B | Page 5 of 36
AD9652
Data Sheet
Parameter
Test Conditions/Comments Temperature Min
Typ Max
Unit
LOGIC INPUT (CSB)2
High Level Input Voltage
Low Level Input Voltage
High Level Input Current
Low Level Input Current
Input Resistance
Full
Full
Full
Full
Full
Full
1.22
0
SPIVDD
0.6
V
V
−65
−135
+65
0
µA
µA
kΩ
pF
26
2
Input Capacitance
LOGIC INPUT (SCLK)3
High Level Input Voltage
Low Level Input Voltage
High Level Input Current
Low Level Input Current
Input Resistance
Full
Full
Full
Full
Full
Full
1.22
0
SPIVDD
0.6
V
V
0
−60
110
+50
µA
µA
kΩ
pF
26
2
Input Capacitance
LOGIC INPUTS (SDIO)2
High Level Input Voltage
Low Level Input Voltage
High Level Input Current
Low Level Input Current
Input Resistance
Full
Full
Full
Full
Full
Full
1.22
0
SPIVDD
0.6
V
V
−65
−135
+70
0
µA
µA
kΩ
pF
26
5
Input Capacitance
LOGIC INPUTS (PDWN)3
High Level Input Voltage
Low Level Input Voltage
High Level Input Current
Low Level Input Current
Input Resistance
Full
Full
Full
Full
Full
Full
1.22
0
−80
−145
DRVDD
0.6
+190
+130
V
V
µA
µA
kΩ
pF
26
5
Input Capacitance
DIGITAL OUTPUTS
LVDS Data and OR Outputs
Assumes nominal 100 Ω
differential termination
ANSI Mode
Differential Output Voltage (VOD)
Output Offset Voltage (VOS)
Reduced Swing Mode
Differential Output Voltage (VOD)
Output Offset Voltage (VOS)
Maximum setting, default
Minimum setting
Full
Full
310
350 450
1.22 1.35
mV
V
1.15
Full
Full
150
200 280
1.22 1.35
mV
V
1.15
1 Input capacitance/resistance refers to the effective capacitance/resistance between one differential input pin and AGND.
2 Internal weak pull-up.
3 Internal weak pull-down.
Rev. B | Page 6 of 36
Data Sheet
AD9652
SWITCHING SPECIFICATIONS
Table 4.
Parameter
Test Conditions/Comments
Temperature
Min Typ
Max
Unit
CLOCK INPUT PARAMETERS (CLK )
Input Clock Rate
Conversion Rate1
Full
Full
Full
80
80
3.2
1240 MHz
310
MSPS
ns
Period—Divide by 1 Mode (tCLK
)
Pulse Width High (tCH), Minimum
Divide by 1 Mode
DCS enabled
DCS disabled
Full
Full
Full
Full
Full
0.8
1.3
0.8
1.0
0.1
ns
ns
ns
ns
Divide by 2 Mode Through Divide by 8 Mode
Aperture Delay (tA)
Aperture Uncertainty (Jitter, tJ)
DATA OUTPUT PARAMETERS
LVDS Mode
ps rms
Data Propagation Delay (tPD)
DCO Propagation Delay (tDCO
Full
Full
Full
Full
Full
Full
Full
290
290
ps
ps
)
DCO to Data Skew (tSKEW
Pipeline Delay (Latency)
Wake-Up Time
)
−80 −280 −480 ps2
26
100
1
Cycles
μs
sec
Cycles
From standby
From power-down
Out of Range Recovery Time
3
1 Conversion rate is the clock rate after the divider.
2 Data transitions prior to DCO edge transition.
TIMING SPECIFICATIONS
Table 5.
Parameter
Test Conditions/Comments
SYNC to the rising edge of CLK+ setup time
Min Typ Max Unit
SYNC TIMING REQUIREMENTS
tSSYNC
tHSYNC
0.1
0.1
ns
ns
SYNC to the rising edge of CLK+ hold time
SPI TIMING REQUIREMENTS
tDS
tDH
tCLK
tS
tH
tHIGH
tLOW
tEN_SDIO
Setup time between the data and the rising edge of SCLK
Hold time between the data and the rising edge of SCLK
Period of the SCLK
Setup time between CSB and SCLK
Hold time between CSB and SCLK
Minimum period that SCLK is in a logic high state
Minimum period that SCLK is in a logic low state
Time required for the SDIO pin to switch from an input to an output relative
to the SCLK falling edge (not shown in Timing Diagrams)
2
2
40
2
2
10
10
10
ns
ns
ns
ns
ns
ns
ns
ns
tDIS_SDIO
tSPI_RST
Time required for the SDIO pin to switch from an output to an input relative
to the SCLK rising edge (not shown in Timing Diagrams)
Time required after power-up, hard or soft reset until SPI access is available
(not shown in Timing Diagrams)
10
ns
μs
500
Rev. B | Page 7 of 36
AD9652
Data Sheet
TimingDiagrams
tA
N – 1
N + 4
N + 5
N
N + 3
VIN±x
N + 1
N + 2
tCH
tCLK
CLK+
CLK–
tDCO
DCO–
DCO+
tSKEW
tPD
PARALLEL
INTERLEAVED
CH A CH B CH A CH B CH A CH B CH A CH B CH A
N – 26 N – 26 N – 25 N – 25 N – 24 N – 24 N – 23 N – 23 N – 22
D0± (LSB)
CHANNEL A
AND
CHANNEL B
CH A CH B CH A CH B CH A CH B CH A CH B CH A
N – 26 N – 26 N – 25 N – 25 N – 24 N – 24 N – 23 N – 23 N – 22
D15± (MSB)
Figure 2. LVDS Data Output Timing
CLK±
SYNC
tSSYNC
tHSYNC
Figure 3. SYNC Timing Inputs
tHIGH
tDS
tCLK
tH
tS
tDH
tLOW
CSB
SCLK DON’T CARE
SDIO DON’T CARE
DON’T CARE
R/W
W1
W0
A12
A11
A10
A9
A8
A7
D5
D4
D3
D2
D1
D0
DON’T CARE
Figure 4. Serial Port Interface Timing Diagram
Rev. B | Page 8 of 36
Data Sheet
AD9652
ABSOLUTE MAXIMUM RATINGS
THERMAL CHARACTERISTICS
Table 6.
Parameter
Rating
Typical θJA is specified for both a 4-layer printed circuit board
(PCB) with a solid ground plane from the JEDEC 51-2 and an
8-layer PCB. The 8-layer PCB has 2 oz copper layers (M1 and
M8), 1 oz copper inner layers, and vias connecting to layers M2,
M5, and M7.
Electrical
AVDD3 to AGND
AVDD_CLK to AGND
AVDD to AGND
DRVDD to AGND
SPIVDD to AGND
−0.3 V to +3.6 V
−0.3 V to +2.0 V
−0.3 V to +2.0 V
−0.3 V to +2.0 V
−0.3 V to +3.6 V
As shown in Table 7, airflow increases heat dissipation, which
reduces θJA. In addition, metal in direct contact with the
package leads from metal traces, through holes, ground, and
power planes, reduces the θJA.
VIN+A/VIN+B, VIN−A/VIN−Bto AGND 1.2 V to 3.0 V
CLK+, CLK− to AGND
−0.3 V to AVDD_CLK +
0.2 V
SYNC to AGND
−0.3 V to AVDD_CLK +
0.2 V
Table 7. Thermal Resistance
Airflow
VCM to AGND
CSB to AGND
SCLK to AGND
−0.3 V to AVDD + 0.2 V
−0.3 V to SPIVDD + 0.3 V
−0.3 V to SPIVDD + 0.3 V
−0.3 V to SPIVDD + 0.3 V
−0.3 V to DRVDD + 0.3 V
−0.3 V to DRVDD + 0.3 V
−0.3 V to DRVDD + 0.3 V
−0.3 V to DRVDD + 0.3 V
Velocity
(m/sec)
2
Package Type
Board Type
8-layer PCB
8-layer PCB
JEDEC1
θJA
Unit
144-Ball CSP_BGA
10 mm × 10 mm
(BC-144-6)
0
15.8 °C/W
13.9 °C/W
21.7 °C/W
19.2 °C/W
SDIO to AGND
1.0
0
PDWN to AGND
OR+/OR− to AGND
D0 Through D15 to AGND
DCO to AGND
1.0
JEDEC1
1 Per JEDEC JESD51-7, plus JEDEC 25-5 2S2P test board.
2 Per JEDEC JESD51-2 (still air) or JEDEC JESD51-6 (moving air).
Environmental
Operating Temperature Range
(Ambient)
Maximum Junction Temperature
Under Bias
−40°C to +85°C
125°C
ESD CAUTION
Storage Temperature Range
(Ambient)
−65°C to +150°C
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
Rev. B | Page 9 of 36
AD9652
Data Sheet
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
AD9652
TOP VIEW
(Not to Scale)
1
2
3
4
5
6
7
8
9
10
11
12
A
B
C
D
E
F
RBIAS
AGND
AGND
CLK–
CLK+
TEST
SYNC
PDWN
D0–
VCM
AVDD3
AVDD3
AVDD
AVDD
AVDD
AVDD
AVDD
AVDD
DRGND
DRVDD
D4+
VIN+B
AGND
AGND
AGND
AGND
AGND
AGND
AGND
DRGND
DRVDD
D5+
VIN–B
AGND
AGND
AGND
AGND
AGND
AGND
AGND
DRGND
SPIVDD
D6+
AVDD3
AVDD3
AVDD3
AVDD3
VIN–A
AGND
AGND
AGND
AGND
AGND
AGND
AGND
DC0+
DC0–
D9+
VIN+A
AGND
AGND
AGND
AGND
AGND
AGND
AGND
DRGND
DRVDD
D10+
AVDD3
AVDD3
AVDD
AVDD
AVDD
AVDD
AVDD
AVDD
DRGND
DRVDD
D11+
SENSE
AVDD3
AGND
AGND
AGND
AGND
AGND
AGND
D15+
VREF
AGND
AGND
CSB
AVDD3
AGND
AGND
AGND
AGND
AGND
AGND
D0+
AVDD_
CLK
AVDD_
CLK
AVDD_
CLK
AVDD_
CLK
AVDD_
CLK
AVDD_
CLK
SDIO
SCLK
OR+
AVDD_
CLK
AVDD_
CLK
G
H
J
AVDD
AVDD
DRGND
DRVDD
D7+
AVDD
AVDD
DRGND
DRVDD
D8+
OR–
D15–
D14–
D13+
D13–
D1–
D1+
D14+
K
L
D2+
D3+
D12+
D2–
D3–
D4–
D5–
D6–
D7–
D8–
D9–
D10–
D11–
D12–
M
Figure 5. Pin Configuration
Table 8. Pin Function Descriptions
Pin No.
Mnemonic
Type
Description
ADC Power Supplies
K5
SPIVDD
DRVDD
AVDD3
Supply
Supply
Supply
Serial Interface Logic Voltage Supply (1.8 V Typical, 3.3 V Optional)
Digital Output Driver Supply (1.8 V Nominal).
K3, K4, K6, K7, K9, K10
A3, A6, A7, A10, B2, B3, B6, B7,
B10, B11
3.3 V Analog Power Supply (3.3 V Nominal).
C6, C7, D6, D7, E6, E7, F6, F7
AVDD_CLK
AVDD
Supply
Supply
1.8 V Analog Power Supply for Clock Circuitry (1.8 V Nominal).
1.8 V Analog Power Supply (1.8 V Nominal).
C3, C10, D3, D10, E3, E10, F3,
F10, G3, G6, G7, G10, H3, H6,
H7, H10
B1, B4, B5, B8, B9, B12, C1, C2,
C4, C5, C8, C9, C11, C12, D2,
D4, D5, D8, D9, D11, E2, E4,
E5, E8, E9, E11, F2, F4, F5, F8,
F9, F11, G2, G4, G5, G8, G9,
G11, H2, H4, H5, H8, H9, H11
AGND
Analog
Ground
Analog Ground Reference for AVDD3, AVDD_CLK, and AVDD.
J3
J4
J5
DRGND
DRGND
DRGND
Digital Ground Digital and Output Driver Ground Reference.
Digital Ground Digital and Output Driver Ground Reference.
Digital Ground Digital and Output Driver Ground Reference.
Rev. B | Page 10 of 36
Data Sheet
AD9652
Pin No.
Mnemonic
DRGND
DRGND
DRGND
DRGND
Type
Description
J6
Digital Ground Digital and Output Driver Ground Reference.
Digital Ground Digital and Output Driver Ground Reference.
Digital Ground Digital and Output Driver Ground Reference.
Digital Ground Digital and Output Driver Ground Reference.
J7
J9
J10
ADC Analog
A9
A8
A4
A5
A2
VIN+A
VIN−A
VIN+B
VIN−B
VCM
Input
Input
Input
Input
Output
Differential Analog Input Pin (+) for Channel A.
Differential Analog Input Pin (−) for Channel A.
Differential Analog Input Pin (+) for Channel B.
Differential Analog Input Pin (−) for Channel B.
Common-Mode Level Bias Output for Analog Inputs. Decouple
this pin to ground using a 0.1 μF capacitor.
A1
RBIAS
Output
External Bias Resister Connection. A 10 kΩ resister must be
connected between this pin and analog ground (AGND).
A12
A11
E1
VREF
Input/Output
Input
Input
Voltage Reference Input/Output.
Reference Mode Selection(See Table 12).
ADC Clock Input (True ).
SENSE
CLK+
CLK−
D1
Input
ADC Clock Input (Complement).
Digital Inputs
F1
TEST
Input
Pull-Down. Unused digital input, pull to ground through a 50 Ω
resistor.
G1
H1
SYNC
Input
Input
Digital Input Clock Synchronization Pin. Tie low if unused.
PDWN
Power-Down Input (Active High). The operation of this pin
depends on the SPI mode and can be configured as power-down
or standby (see Register 0x08 in Table 17).
Digital Outputs
J2
J1
K2
D0+
D0−
D1+
D1−
D2+
D2−
D3+
D3−
D4+
D4−
D5+
D5−
D6+
D6−
D7+
D7−
D8+
D8−
D9+
D9−
D10+
D10−
D11+
D11−
D12+
D12−
D13+
D13−
D14+
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Channel A/Channel B LVDS Output Data 0 (True , LSB).
Channel A/Channel B LVDS Output Data 0 (Complement, LSB).
Channel A/Channel B LVDS Output Data 1 (True ).
K1
L1
M1
L2
M2
L3
Channel A/Channel B LVDS Output Data 1 (Complement).
Channel A/Channel B LVDS Output Data 2 (True).
Channel A/Channel B LVDS Output Data 2 (Complement).
Channel A/Channel B LVDS Output Data 3 (True ).
Channel A/Channel B LVDS Output Data 3 (Complement).
Channel A/Channel B LVDS Output Data 4 (True ).
M3
L4
M4
L5
Channel A/Channel B LVDS Output Data 4 (Complement).
Channel A/Channel B LVDS Output Data 5 (True ).
Channel A/Channel B LVDS Output Data 5 (Complement).
Channel A/Channel B LVDS Output Data 6 (True ).
M5
L6
M6
L7
M7
L8
Channel A/Channel B LVDS Output Data 6 (Complement).
Channel A/Channel B LVDS Output Data 7 (True ).
Channel A/Channel B LVDS Output Data 7 (Complement).
Channel A/Channel B LVDS Output Data 8 (True ).
Channel A/Channel B LVDS Output Data 8 (Complement).
Channel A/Channel B LVDS Output Data 9 (True ).
M8
L9
Channel A/Channel B LVDS Output Data 9 (Complement).
Channel A/Channel B LVDS Output Data 10 (True ).
Channel A/Channel B LVDS Output Data 10 (Complement).
Channel A/Channel B LVDS Output Data 11 (True ).
Channel A/Channel B LVDS Output Data 11 (Complement).
Channel A/Channel B LVDS Output Data 12 (True ).
Channel A/Channel B LVDS Output Data 12 (Complement).
Channel A/Channel B LVDS Output Data 13 (True).
Channel A/Channel B LVDS Output Data 13 (Complement).
Channel A/Channel B LVDS Output Data 14 (True ).
M9
L10
M10
L11
M11
L12
M12
K11
Rev. B | Page 11 of 36
AD9652
Data Sheet
Pin No.
K12
J11
Mnemonic
D14−
D15+
D15−
OR+
OR−
DCO+
DCO−
Type
Description
Output
Output
Output
Output
Output
Output
Output
Channel A/Channel B LVDS Output Data 14 (Complement).
Channel A/Channel B LVDS Output Data 15 (True , MSB).
Channel A/Channel B LVDS Output Data 15 (Complement, MSB).
Channel A/Channel B LVDS Overrange (True ).
Channel A/Channel B LVDS Overrange (Complement).
Channel A/Channel B LVDS Data Clock Output (True ).
Channel A/Channel B LVDS Data Clock Output (Complement).
J12
G12
H12
J8
K8
SPI Control
F12
E12
SCLK
SDIO
CSB
Input
Input/Output
Input
SPI Serial Clock.
SPI Serial Data Input/Output.
D12
SPI Chip Select (Active Low). This pinmust be pulledhigh at
power-up.
Rev. B | Page 12 of 36
Data Sheet
AD9652
TYPICAL PERFORMANCE CHARACTERISTICS
AVD D 3 = 3.3 V, AVDD = AVDD_CLK = 1.8 V, SPIVDD = DRVDD = 1.8 V, sample rate = 310 MSPS (clock input = 1240 MHz, AD9652
divide by 4), VIN = −1.0 dBFS differential, VREF = 1.25 V, DCS enabled, dither disabled, unless otherwise noted.
0
–20
0
A
= –1dBFS
A
= –1dBFS
IN
IN
SNRFS = 75.0dB
SFDR = 89dBc
SNRFS = 74.4dB
SFDR = 90dBc
–20
–40
–40
–60
–60
–80
–80
–100
–120
–140
–100
–120
–140
0
20
40
60
80
100
120
140
0
20
40
60
80
100
120
140
fIN (MHz)
fIN (MHz)
Figure 6. Single Tone Fast Fourier Transform (FFT) with fIN = 70.1 MHz
(NSD = −156.7 dBFS/Hz)
Figure 9. Single Tone FFT with fIN = 70.1 MHz with Dither
(NSD = −156.3 dBFS/Hz)
0
0
A
= –7dBFS
A
= –7dBFS
IN
IN
SNRFS = 75.7dB
SFDR = 91.9dBc
SNRFS = 75.2dB
SFDR = 94.4dBc
–20
–40
–20
–40
–60
–60
–80
–80
–100
–120
–140
–100
–120
–140
0
20
40
60
80
100
120
140
0
20
40
60
80
100
120
140
fIN (MHz)
fIN (MHz)
Figure 10. Single Tone FFT with fIN = 70.1 MHz at −7 dBFS with Dither
(NSD = −157.1 dBFS/Hz)
Figure 7. Single Tone FFT with fIN = 70.1 MHz at −7 dBFS
(NSD = −157.6 dBFS/Hz)
0
0
A
= –1dBFS
IN
A
= –1dBFS
IN
SNRFS = 72.9dB
SFDR = 88dBc
SNRFS = 73.2dB
SFDR = 88dBc
–20
–40
–20
–40
–60
–60
–80
–80
–100
–120
–140
–100
–120
–140
0
20
40
60
80
100
120
140
0
20
40
60
80
100
120
140
fIN (MHz)
fIN (MHz)
Figure 8. Single Tone FFT with fIN = 185 MHz. at −1 dBFS
(NSD = −155.2 dBFS/Hz), Register 0x22A = 0x01
Figure 11. Single Tone FFT with fIN = 185 MHz at −1 dBFS with Dither
(NSD = −154.9 dBFS/Hz), Register 0x22A = 0x01
Rev. B | Page 13 of 36
AD9652
Data Sheet
0
0
–20
A
= –7dBFS
A
= –7dBFS
IN
IN
SNRFS = 75dB
SFDR = 92dBc
SNRFS = 74.5dB
SFDR = 93dBc
–20
–40
–40
–60
–60
–80
–80
–100
–120
–140
–100
–120
–140
0
20
40
60
80
100
120
140
0
20
40
60
80
100
120
140
fIN (MHz)
fIN (MHz)
Figure 12. Single Tone FFT with fIN = 185 MHz at −7 dBFS
(NSD = −156.9 dBFS/Hz), Register 0x22A = 0x01
Figure 15. Single Tone FFT with fIN = 185 MHz at −7dBFS with Dither
(NSD = −156.4 dBFS/Hz), Register 0x22A = 0x01
0
0
A
= –1dBFS
A
= –1dBFS
IN
IN
SNRFS = 69.7dB
SNRFS = 69.5dB
SFDR = 86.9dBc
SFDR = 91.6dBc
–20
–20
–40
–40
–60
–60
–80
–80
–100
–120
–140
–100
–120
–140
0
50
100
150
0
50
100
150
fIN (MHz)
fIN (MHz)
Figure 13. FFT fIN = 305 MHz, AIN = −1 dBFS, Dither Off, Register 0x22A = 0x01
Figure 16. FFT fIN = 305 MHz, AIN = −1 dBFS, Dither On, Register 0x22A = 0x01
0
0
A
= –7dBFS
A
= –7dBFS
IN
IN
SNRFS = 72.7dB
SNRFS = 72.8dB
SFDR = 90.7dBc
SFDR = 90.7dBc
–20
–40
–20
–40
–60
–60
–80
–80
–100
–120
–140
–100
–120
–140
0
50
100
150
0
50
100
150
fIN (MHz)
fIN (MHz)
Figure 14. FFT fIN = 305 MHz, AIN = −7 dBFS, Dither Off, Register 0x22A = 0x01
Figure 17. FFT fIN = 305 MHz, AIN = −7 dBFS, Dither On, Register 0x22A = 0x01
Rev. B | Page 14 of 36
Data Sheet
AD9652
0
0
–20
A
= –1dBFS
A
= –1dBFS
IN
IN
SNRFS = 68.0dB
SFDR = 75.7dBc
SNRFS = 68.0dB
SFDR = 75.0dBc
–20
–40
–40
–60
–60
–80
–80
–100
–120
–100
–120
–140
–140
0
50
100
150
0
50
100
150
fIN (MHz)
fIN (MHz)
Figure 18. FFT fIN = 400 MHz, AIN = −1 dBFS, Dither Off, Register 0x22A = 0x02
Figure 21. FFT fIN = 400 MHz, AIN = −1 dBFS, Dither On, Register 0x22A = 0x02
0
0
A
= –7dBFS
A
= –7dBFS
IN
IN
SNRFS = 71.7dB
SNRFS = 71.9dB
SFDR = 81.3dBc
SFDR = 80.2dBc
–20
–40
–20
–40
–60
–60
–80
–80
–100
–120
–140
–100
–120
–140
0
50
100
150
0
50
100
150
fIN (MHz)
fIN (MHz)
Figure 19. FFT fIN = 400 MHz, AIN = −7 dBFS, Dither Off, Register 0x22A = 0x02
Figure 22. FFT fIN = 400 MHz, AIN = −7 dBFS, Dither On, Register 0x22A = 0x02
78
76
74
72
70
68
66
64
62
60
140
120
100
80
78
76
74
72
70
68
66
64
62
60
140
120
100
80
SNRFS (dB), –40°C
SNRFS (dB), +25°C
SNRFS (dB), +85°C
SFDR (dBFS), –40°C
SFDR (dBFS), +25°C
SFDR (dBFS), +85°C
SFDR (dBc), –40°C
SFDR (dBc), +25°C
SFDR (dBc), +85°C
SNRFS (dB), –40°C
SNRFS (dB), +25°C
SNRFS (dB), +85°C
SFDR (dBFS), –40°C
SFDR (dBFS), +25°C
SFDR (dBFS), +85°C
SFDR (dBc), –40°C
SFDR (dBc), +25°C
SFDR (dBc), +85°C
60
60
40
40
20
20
–80
–60
–40
–20
0
–80
–60
–40
–20
0
A
(–dBFS)
A
(–dBFS)
IN
IN
Figure 20. Single Tone SNR/SFDR vs. Input Amplitude (AIN) with
fIN = 90.1 MHz, VREF = 1.25 V, Over Temperature, Dither Off
Figure 23. Single Tone SNR/SFDR vs. Input Amplitude (AIN) with
fIN = 90.1 MHz, VREF = 1.25 V, Over Temperature, Dither On
Rev. B | Page 15 of 36
AD9652
Data Sheet
78
76
74
72
70
68
66
64
62
140
120
100
80
78
76
74
72
70
68
66
64
62
60
140
120
100
80
SNRFS (dB), –40°C
SNRFS (dB), +25°C
SNRFS (dB), +85°C
SFDR (dBFS), –40°C
SFDR (dBFS), +25°C
SFDR (dBFS), +85°C
SFDR (dBc), –40°C
SFDR (dBc), +25°C
SFDR (dBc), +85°C
SNRFS (dB), –40°C
SNRFS (dB), +25°C
SNRFS (dB), +85°C
SFDR (dBFS), –40°C
SFDR (dBFS), +25°C
SFDR (dBFS), +85°C
SFDR (dBc), –40°C
SFDR (dBc), +25°C
SFDR (dBc), +85°C
60
60
40
40
60
–80
20
20
0
–60
–40
–20
0
–80
–60
–40
–20
A
(–dBFS)
A
(–dBFS)
IN
IN
Figure 24. Single Tone SNR/SFDR vs. Input Amplitude (AIN) with
fIN = 90.1 MHz, VREF = 1.0 V, Over Temperature, Dither Off
Figure 27. Single Tone SNR/SFDR vs. Input Amplitude (AIN) with fIN =
90.1 MHz, VREF = 1.0 V, Over Temperature, Dither On
76
74
72
70
68
66
64
62
60
58
56
110
76
74
72
70
68
66
64
62
60
58
56
110
106
102
98
SNRFS
SNRFS
(NYQUIST SETTING 1)
(NYQUIST SETTING 1)
106
102
98
94
90
86
82
78
74
70
SNRFS
(NYQUIST SETTING 2)
SNRFS
(NYQUIST SETTING 3)
SNRFS
(NYQUIST SETTING 2)
SNRFS
(NYQUIST SETTING 3)
94
90
86
82
SFDR
SFDR
78
(NYQUIST SETTING 1)
(NYQUIST SETTING 1)
SFDR
(NYQUIST SETTING 2)
SFDR
(NYQUIST SETTING 3)
SFDR
(NYQUIST SETTING 2)
SFDR
(NYQUIST SETTING 3)
74
70
0
50 100 150 200 250 300 350 400 450 500 550
0
50 100 150 200 250 300 350 400 450 500 550
fIN (MHz)
fIN (MHz)
Figure 25. Single Tone SNR/SFDR vs. Input Frequency (fIN),
Amplitude = −1 dBFS, VREF = 1.25 V
Figure 28. Single Tone SNR/SFDR vs. Input Frequency (fIN),
Amplitude =−1 dBFS, VREF = 1.0 V
76
74
72
70
68
66
64
62
60
58
56
110
106
102
98
76
74
72
70
68
66
64
62
60
58
56
110
106
102
98
SNRFS
SNRFS
(NYQUIST SETTING 1)
(NYQUIST SETTING 1)
SNRFS
(NYQUIST SETTING 2)
SNRFS
(NYQUIST SETTING 3)
SNRFS
(NYQUIST SETTING 2)
SNRFS
(NYQUIST SETTING 3)
94
94
90
90
86
86
82
82
SFDR
(NYQUIST SETTING 1)
SFDR
(NYQUIST SETTING 2)
SFDR
(NYQUIST SETTING 3)
SFDR
(NYQUIST SETTING 1)
SFDR
(NYQUIST SETTING 2)
SFDR
(NYQUIST SETTING 3)
78
78
74
74
70
70
0
50 100 150 200 250 300 350 400 450 500 550
0
50 100 150 200 250 300 350 400 450 500 550
fIN (MHz)
fIN (MHz)
Figure 26. Single Tone SNR/SFDR vs. Input Frequency (fIN),
Amplitude = −7 dBFS, VREF = 1.25 V
Figure 29. Single Tone SNR/SFDR vs. Input Frequency (fIN),
Amplitude = −7 dBFS, VREF = 1.0 V
Rev. B | Page 16 of 36
Data Sheet
AD9652
0
–20
–40
–60
105
100
95
0
–20
105
100
95
–40
90
–60
90
SFDR (dBFS)
SFDR (dBFS)
IMD2 (dBc)
IMD3 (dBc)
IMD2 (dBFS)
IMD3 (dBFS)
IMD2 (dBc)
IMD3 (dBc)
IMD2 (dBFS)
IMD3 (dBFS)
–80
–100
–120
85
–80
85
80
–100
–120
80
75
75
0
–80
–60
–40
INPUT AMPLITUDE (dBFS)
–20
0
–80
–60
–40
INPUT AMPLITUDE (dBFS)
–20
Figure 30. Two Tone SFDR/Intermodulation Distortion (IMD) vs. Input
Amplitude, for fIN = 70.1 MHz and 72.1 MHz, Dither Disabled
Figure 33. Two Tone SFDR/IMD vs. Input Amplitude, for fIN = 70.1 MHz and
72.1 MHz, Dither Enabled
0
105
100
95
0
105
100
95
–20
–20
–40
–40
–60
90
–60
90
SFDR (dBFS)
IMD2 (dBc)
IMD3 (dBc)
IMD2 (dBFS)
IMD3 (dBFS)
SFDR (dBFS)
IMD2 (dBc)
IMD3 (dBc)
IMD2 (dBFS)
IMD3 (dBFS)
–80
85
–80
85
–100
–120
80
–100
–120
80
75
75
–80
–60
–40
INPUT AMPLITUDE (dBFS)
–20
0
–80
–60
–40
INPUT AMPLITUDE (dBFS)
–20
0
Figure 31. Two Tone SFDR/IMD vs. Input Amplitude, for fIN = 184 MHz and
187 MHz, Dither Disabled, Register 0x22A = 0x01
Figure 34. Two Tone SFDR/IMD vs. Input Amplitude, for fIN = 184 MHz and
187 MHz, Dither Enabled, Register 0x22A = 0x01
70000
60000
50000
40000
30000
20000
10000
0
0
A
1 = A 2 = –7dBFS
IN
IN
SFDR = 87dBc (94dBFS)
IMD2 = –92dBc (–99dBFS)
IMD3 = –87dBc (–94dBFS)
–20
–40
–60
–80
–100
–120
–140
0
25
50
75
100
125
150
fIN (MHz)
CODES
Figure 35. Grounded Input Histogram
Figure 32. Two Tone FFT with fIN = 89.1 MHz and 92.1 MHz, VREF = 1.25 V
Rev. B | Page 17 of 36
AD9652
Data Sheet
100
95
90
85
80
75
100
95
90
85
80
75
70
SFDR (V
= 1V)
REF
SFDR (V
= 1V)
REF
SFDR (V
= 1.25V)
REF
SFDR (V
= 1.25V)
REF
SNRFS (V
= 1.25V)
= 1V)
REF
SNRFS (V
= 1.25V)
= 1V)
REF
SNRFS (V
SNRFS (V
REF
REF
70
80
120
160
200
240
280
320
80
120
160
200
240
280
320
ENCODE RATE (MHz)
ENCODE RATE (MHz)
Figure 36. Encode Rate Sweep, fIN = 90.1 MHz at −7 dBFS,
VREF = 1.25 V and 1.0 V
Figure 39. Encode Rate Sweep, fIN = 90.1 MHz at −1 dBFS,
VREF = 1.25 V and 1.0 V
1.0
6
0.8
0.6
3
0
0.4
0.2
0
–0.2
–0.4
–0.6
–0.8
–1.0
–3
–6
0
10000
20000
30000
CODES
40000
50000
60000
0
10000
20000
30000
CODES
40000
50000
60000
Figure 37. DNL with Dither Off, fIN = 30 MHz
Figure 40. INL with Dither Off, fIN = 30 MHz
1.0
0.8
6
3
0.6
0.4
0.2
0
0
–0.2
–0.4
–0.6
–0.8
–1.0
–3
–6
0
10000
20000
30000
CODES
40000
50000
60000
0
10000
20000
30000
CODES
40000
50000
60000
Figure 41. INL with Dither On, fIN = 30 MHz
Figure 38. DNL with Dither On, fIN = 30 MHz
Rev. B | Page 18 of 36
Data Sheet
AD9652
EQUIVALENT CIRCUITS
SPIVDD
AVDD3
350ꢀ
SCLK
VIN±x
26kꢀ
27kΩ
Figure 42. Equivalent Analog Input Circuit
Figure 47. Equivalent SCLK Input Circuit
AVDD_CLK
SPIVDD
AVDD
AVDD
26kꢀ
0.9V
350ꢀ
10kꢀ
10kꢀ
CSB
CLK+
CLK–
Figure 48. Equivalent CSB Input Circuit
Figure 43. Equivalent Clock Circuit
DRVDD
AVDD_CLK
AVDD_CLK
V+
V–
DATAOUT–
V–
DATAOUT+
V+
SYNC
0.9V
16kꢀ
0.9V
Figure 49. Equivalent SYNC Input Circuit
Figure 44. Equivalent LVDS Output Circuit (DCO± ± Oꢀ± ± and D0± to D15± )
AVDD
SPIVDD
26kꢀ
350ꢀ
SENSE
350ꢀ
SDIO
Figure 50. Equivalent SENSE Circuit
Figure 45. Equivalent SDIO Circuit
AVDD
350ꢀ
VREF
PDWN
6kꢀ
26kꢀ
Figure 46. Equivalent PDWN Input Circuit
Figure 51. Equivalent VꢀEF Circuit
Rev. B | Page 19 of 36
AD9652
Data Sheet
THEORY OF OPERATION
The AD9652 is a dual, 16-bit ADC with sampling speeds of up
to 310 MSPS. The AD9652 is designed to support communications
and instrumentation applications where high performance and
wide bandwidth are desired.
ANALOG INPUT CONSIDERATIONS
The analog inputs to the AD9652 are high performance
differential buffers that are designed for optimum performance
while processing a differential input signal. The input buffer
provides a consistent input impedance to ease interface of the
analog input.
The dual ADC design can be used for diversity receivers, where
the ADCs operate identically on the same carrier but from two
separate antennae. The ADCs can also be operated with
independent analog inputs. The user can sample frequencies
from dc to 310 MHz using appropriate low-pass or band-pass
filtering at the ADC inputs with little loss in ADC performance.
A typical operation of 485 MHz at the analog input is permitted
but occurs at the expense of increased ADC noise and distortion.
The differential analog input impedance is approximately 54 kΩ
in parallel with a 5.8 pF capacitor. A passive network of discrete
components can create a low-pass filter at the ADC input; the
precise values are dependent on the application.
In intermediate frequency (IF) undersampling applications,
reduce the shunt capacitors. In combination with the driving
source impedance, the shunt capacitors limit the input bandwidth.
Refer to the Analog Dialogue article, “Transformer-Coupled
Front-End for Wideband A/D Converters,” for more information
on this subject.
Synchronization capability is provided to allow synchronized
timing between multiple devices.
Programming and control of the AD9652 are accomplished
using a 3-wire, SPI-compatible serial interface.
The AD9652 uses internal optimized settings for the various
input signal frequencies. Register 0x22A configures the ADC
for the desired frequency band.
ADC ARCHITECTURE
The AD9652 consists of a dual, buffered front-end sample-and-
hold circuit, followed by a pipelined switched-capacitor ADC.
The AD9652 uses a unique architecture that utilizes the benefits
of pipelined converters, as well as a novel input circuit to
maximize performance of the first stage.
Table 9. Register 0x22A Settings
Register 0x22A Setting
Input Frequency Range
0 (Default)
1
2
0 to 155 MHz (1st Nyquist)
155 to 310 MHz (2nd Nyquist)
310 MHz and above (3rd Nyquist)
The quantized outputs from each stage are combined to produce a
16-bit result in the digital correction logic. The pipelined
architecture permits the first stage to operate on a new input
sample, and the remaining stages to operate on the preceding
samples. Sampling occurs on the rising edge of the clock.
For best dynamic performance, the source impedances driving
each of the differential inputs, match VIN x, and differentially
balance the inputs.
Each stage of the pipeline, excluding the last, consists of a low
resolution flash ADC connected to a switched-capacitor digital-
to-analog converter (DAC) and an interstage residual multiplying
DAC (MDAC). The MDAC magnifies the difference between
the reconstructed DAC output and the flash input for the next
stage in the pipeline. One bit of redundancy is used in each
stage to facilitate digital correction of flash errors. The last stage
consists of a flash ADC.
Input Common Mode
The analog inputs of the AD9652 are not internally dc biased.
In ac-coupled applications, the user must provide this bias
externally. Setting the device so that the common-mode voltage
equals 2.0 V is recommended for optimum performance. An
on-board common-mode voltage reference is included in the
design and is available from the VCM pin. Using the VCM
output to set the input common mode is recommended. The
VCM pin must be decoupled to ground with a 0.1 μF capacitor,
as described in the Applications Information section. Place this
decoupling capacitor close to the pin to minimize the series
resistance and inductance between the device and this capacitor.
The AD9652 uses internal digital processing to continually
track internal errors that occur at each of the pipeline stages and
corrects for them to ensure continuous performance over
various operating conditions. This requires additional start-up
time due to the resetting and collection of correction data.
Common-Mode Voltage Servo
The input stage of each channel contains a differential sampling
circuit that can be ac- or dc-coupled in differential or single-
ended modes. The output staging block aligns the data, corrects
errors, and passes the data to the output buffers. The output
buffers are powered from a separate supply, allowing digital
output noise to be separated from the analog core. During power-
down, the output buffers enter a high impedance state.
In applications where there may be a voltage loss between the VCM
output of the AD9652 and the analog inputs, the common-mode
voltage servo can be enabled. When the inputs are ac-coupled and a
resistance of >100 Ω is placed between the VCM output and the
analog inputs, a significant voltage drop can occur; enable the
common-mode voltage servo. Setting Bit 0 in Register 0x0F to a
logic high enables the VCM servo mode.
Rev. B | Page 20 of 36
Data Sheet
AD9652
In this mode, the AD9652 monitors the common-mode input
level at the analog inputs and adjusts the VCM output level to
keep the common-mode input voltage at an optimal level. If
both channels are operational, Channel A is monitored.
However, if Channel A is in power-down or standby mode, then
Channel B input is monitored.
Large Signal Fast Fourier Transform
In most cases, dithering does not improve SFDR for large signal
inputs close to full scale, for example, with a −1 dBFS input. For
large signal inputs, the SFDR is typically limited by front-end
sampling distortion, which dithering cannot improve. However,
even for such large signal inputs, dithering can be useful for
certain applications because it makes the noise floor whiter. As
is common in pipeline ADCs, the AD9652 contains small DNL
errors caused by random component mismatches that produce
spurs or tones that make the noise floor somewhat randomly
colored device-to-device. Although these tones are typically at
very low levels and do not limit SFDR when the ADC is
quantizing large signal inputs, dithering converts these tones to
noise and produces a whiter noise floor.
Dither
The AD9652 has an optional internal dither circuitry that can
improve SFDR, particularly for small signals. Dithering is the act
of injecting a known but random amount of white noise into the
input of the AD9652. Dithering has the effect of improving the
local linearity within the ADC transfer function. The AD9652
allows dither to be added to either ADC input independently.
The full scale of the dither DAC is small enough that enabling
dither does not limit the external input signal amplitude.
Small Signal FFT
As shown in Figure 52, the dither that is added to the input of
the ADC through the dither DAC is precisely subtracted out
digitally to minimize SNR degradation. When dithering is
enabled, the dither DAC is driven by a pseudorandom number
generator (PN gen). In the AD9652, the dither DAC is precisely
calibrated to result in only a very small degradation in SNR and
SINAD when dither is enabled.
For small signal inputs, the front-end sampling circuit typically
contributes very little distortion, and the SFDR is likely to be
limited by tones caused by DNL errors due to random component
mismatches. Therefore, for small signal inputs (typically, those
below −6 dBFS), dithering can significantly improve SFDR by
converting these DNL tones to white noise.
Static Linearity
AD9652
Dithering also removes sharp local discontinuities in the INL
transfer function of the ADC and reduces the overall peak-to-
peak INL.
VIN±x
DOUT
ADC CORE
Utilizing dither randomizes local small signal DNL errors that
produce the discontinuities in the INL transfer function and
therefore improve the peak-to-peak INL performance.
DITHER
DAC
PN GEN
DITHER ENABLE
Differential Input Configurations
Optimum performance is achieved by driving the AD9652 in a
differential input configuration. For baseband applications, the
ADL5566, AD8138, ADA4937-2, ADA4938-2, and ADA4930-2
differential drivers provide excellent performance and a flexible
interface to the ADC.
Figure 52. Dither Block Diagram
The SFDR improvement comes at the expense of SNR
degradation, but because the dither is internal and can be
correlated, the impact on SNR is typically limited to less than
0.5 dB in the first Nyquist zone. Enabling internal dither does
not impact full-scale dynamic range. The magnitude of dither is
controllable, which allows the user to select the desired trade-
off between SFDR improvement vs. SNR degradation.
The output common-mode voltage of the ADA4930-2 is easily
set with the VCM pin of the AD9652 (see Figure 53), and the
driver can be configured in a Sallen-Key filter topology to
provide band limiting of the input signal.
15pF
To enable dither, set Bit 4 of Register 0x30. To modify the dither
gain, use Register 0x212[7:4].
200Ω
33Ω
5pF
15Ω
Table 10. Dither Gain
90Ω
VIN–x
ADC
VCM
VIN±x
76.8Ω
Register 0x212[7:4] Setting
0b0000 (default)
0b0001
0b0010
0b0011
0b0100
0b0101
0b0110
0b0111
Gain Ratio
Gain (%)
100
ADA4930-2
Maximum dither
255/256 × max
254/256 × max
252/256 × max
248/256 × max
240/256 × max
224/256 × max
192/256 × max
Minimum dither
0.1µF
33Ω
15Ω
99.6
99.2
98.4
96.8
93.75
87.5
75
VIN+x
120Ω
15pF
200Ω
33Ω
0.1µF
Figure 53. Differential Input Configuration Using the ADA4930-2
0b1000
50
Rev. B | Page 21 of 36
AD9652
Data Sheet
For baseband applications where SNR is a key parameter,
differential transformer coupling is the recommended input
configuration. An example is shown in Figure 54. To bias the
analog input, the VCM voltage can be connected to the center
tap of the secondary winding of the transformer.
input frequency ranges. However, these values are dependent on
the input signal; use the bandwidth only as a starting guide.
Note that the values given in Table 11 are for each R1, R2, C1,
C2, and R3 component shown in Figure 54 and Figure 56.
Table 11. Example RC Network
C2
Frequency
Range
(MHz)
R1
C1
R2
C2
R3
R3
Series Differential Series Shunt Shunt
(Ω)
33
R2
VIN+x
(pF)
(Ω)
0
15
(pF)
15
2.7
(Ω)
49.9
0
R1
0 to 100
100 to 300
Open
Open
2V p-p
49.9Ω
C1
R1
ADC
15
R2
VCM
VIN–x
An alternative to using a transformer-coupled input at
0.1µF
33Ω
0.1µF
R3
frequencies in the second Nyquist zone is to use an amplifier
with variable gain. The AD8375 or AD8376 digital variable gain
amplifier (DVGA) provides good performance for driving the
AD9652. Figure 55 shows an example of the AD8376 driving
the AD9652 through a band-pass antialiasing filter.
C2
Figure 54. Differential Transformer-Coupled Configuration
The signal characteristics must be considered when selecting a
transformer. Most RF transformers saturate at frequencies
below a few megahertz. Excessive signal power can also cause
core saturation, which leads to distortion.
1000pF 180nH 220nH
1µH
1µH
165Ω
165Ω
15pF
VPOS
1nF
AD9652
At input frequencies in the second Nyquist zone and above, the
noise performance of most amplifiers is not adequate to achieve
the true SNR performance of the AD9652. For applications
where SNR is a key parameter, differential double balun coupling is
the recommended input configuration (see Figure 56). In this
configuration, the input is ac-coupled and the VCM voltage is
provided to each input through a 33 Ω resistor. These resistors
compensate for losses in the input baluns to provide a 50 Ω
impedance to the driver.
AD8376
5.1pF
3.9pF
VCM
1nF
54kΩ║2.9pF
301Ω
68nH
180nH 220nH
®
1000pF
NOTES
1. ALL INDUCTORS ARE COILCRAFT 0603CS COMPONENTS WITH THE
EXCEPTION OF THE 1µH CHOKE INDUCTORS (COIL CRAFT 0603LS).
2. FILTER VALUES SHOWN ARE FOR A 20MHz BANDWIDTH FILTER
CENTERED AT 140MHz.
Figure 55. Differential Input Configuration Using the AD8376
In the double balun and transformer configurations, the value
of the input capacitors and resistors is dependent on the input
frequency and source impedance. Based on these parameters,
the value of the input resistors and capacitors may need to be
adjusted, or some components may need to be removed. Table 11
displays recommended values to set the RC network for different
C2
R3
0.1µF
0.1µF
R1
R2
R2
VIN+x
2V p-p
33Ω
33Ω
P
A
S
S
P
C1
R1
ADC
0.1µF
0.1µF
VCM
VIN–x
R3
33Ω
0.1µF
C2
Figure 56. Differential Double Balun Input Configuration
Table 12. VREF Configuration Options
Selected Mode
SENSE Voltage
Resulting ADC Reference Voltage (V)
Resulting Input Span (Differential V p-p)
External Reference
Internal Fixed Reference
AVDD
GND
N/A1
2 × external reference
2
2
VREF
2 × VREF
1 N/A means not applicable.
2 VREF is set via Register 0x18. The default VREF is 1.25 V.
Rev. B | Page 22 of 36
Data Sheet
AD9652
0
–1
–2
–3
–4
VOLTAGE REFERENCE
V
= 1.25V
REF
A stable and accurate voltage reference is built into the AD9652.
The full-scale input range can be adjusted by varying the reference
voltage via the SPI. The input span of the ADC linearly tracks
reference voltage changes.
Internal Reference Connection
A stable and accurate programmable reference is built into
the AD9652, allowing a voltage reference from 1.0 V to 1.25 V
to provide up to a 2.5 V p-p differential full-scale input. By
default the VREF voltage is set 1.25 V, but can be modified using
Register 0x18[2:0], VREF select.
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
To configure the AD9652 for an internal reference, the SENSE
pin must be tied low. When SENSE is tied low, the ADC uses
LOAD CURRENT (mA)
Figure 58. Reference Voltage Error vs. Load Current
VREF directly and provides a differential input voltage of two
times the VREF value.
External Reference Operation
The use of an external reference can be necessary to enhance
the gain accuracy of the ADC or improve thermal drift charac-
teristics.
To achieve optimal noise performance when using the internal
reference, it is recommended that the VREF pin be decoupled
by 1.0 μF and 0.1 μF capacitors close to the pin. Figure 57 shows
the configuration for the internal reference connection resulting
in a input voltage set by VREF, that is, a 2.5 V p-p differential
full-scale input.
When the SENSE pin is tied to AVDD, the internal reference is
disabled, allowing the use of an external reference that is
applied to the VREF pin. An internal reference buffer loads the
external reference with an equivalent 6 kΩ load. The internal
buffer generates the positive and negative full-scale references
for the ADC core. Therefore, the external reference must be
limited to a maximum of 1.25 V to maintain an input voltage of
2.5 V p-p differential full-scale input or less.
VIN+A/VIN+B
VIN–A/VIN–B
ADC
CORE
CLOCK INPUT CONSIDERATIONS
VREF
For optimum performance, clock the AD9652 sample clock
inputs, CLK+ and CLK−, with a differential signal with a high
slew rate. The signal is typically ac-coupled into the CLK+ and
CLK− pins via a transformer or via capacitors. These pins are
biased internally (see Figure 59) and require no external bias. If
the inputs are floated, the CLK− pin is intentionally biased
slightly lower than CLK+ to prevent spurious clocking (this is
not shown in Figure 59).
1.0µF
0.1µF
SELECT
LOGIC
SENSE
V
SELECT
AD9652
Figure 57. Internal Reference Configuration
AVDD_CLK
If the internal reference of the AD9652 drives multiple
converters to improve gain matching, the loading of the reference
by the other converters must be considered. Figure 58 shows how
the internal reference voltage is affected by loading.
0.9V
CLK+
CLK–
5pF
5pF
Figure 59. Simplified Equivalent Clock Input Circuit
Rev. B | Page 23 of 36
AD9652
Data Sheet
Clock Input Options
A third option is to ac couple a differential LVDS signal to the
sample clock input pins, as shown in Figure 63. The AD9510,
AD9511, AD9512, AD9513, AD9514, AD9515, AD9516-5,
AD9517-1, AD9518-1, AD9520-5, AD9522-1, AD9523, and
AD9524 clock drivers offer excellent jitter performance.
The AD9652 has a very flexible clock input structure. The clock
input can be a CMOS, LVDS, LVPECL, or sine wave signal.
Regardless of the type of signal being used, clock source jitter is
of the most concern, as described in the Jitter Considerations
section.
Figure 60 and Figure 61 show two preferable methods for
clocking the AD9652 (at clock rates of up to 1240 MHz). A low
jitter clock source is converted from a single-ended signal to a
differential signal using an RF balun or RF transformer.
ADC
0.1µF
0.1µF
CLOCK
INPUT
CLK+
AD95xx
LVDS DRIVER
100Ω
0.1µF
0.1µF
CLOCK
INPUT
CLK–
50kΩ
50kΩ
The RF balun configuration is recommended for clock
frequencies between 125 MHz and 1240 MHz, and the RF
transformer is recommended for clock frequencies from
80 MHz to 200 MHz. The back-to-back Schottky diodes are
used across the transformer secondary or the balun balanced
side to limit clock amplitude excursions into the AD9652 to
approximately 0.8 V p-p differential. This limit helps prevent
large voltage swings of the clock from feeding through to other
portions of the AD9652, while preserving fast rise and fall times
of the clock, which are critical to low jitter performance.
Figure 63. Differential LVDS Sample Clock (Up to 625 MHz)
Input Clock Divider
The AD9652 contains an input clock divider with the ability to
divide the input clock by integer values of 1, 2, 4 or 8. In these
cases, the DCS is enabled by default on power-up. The clock
divide ratio is set in Register 0x0B.
The AD9652 clock divider can be synchronized using the
external SYNC input. Bit 1 and Bit 2 of Register 0x100 allow the
clock divider to be resynchronized on every SYNC signal or
only on the first SYNC signal after the register is written. A
valid SYNC causes the clock divider to reset to its initial state.
This synchronization feature allows multiple devices to have
their clock dividers aligned to guarantee simultaneous input
sampling. With the divider enabled and the SYNC option used,
the ADC clock divider output phase can be adjusted after
synchronization in increments of input clock cycles using
Register 0x16.
®
Mini-Circuits
ADT1-1WT, 1:1Z
ADC
390pF
390pF
390pF
XFMR
CLOCK
INPUT
CLK+
CLK–
100Ω
50Ω
SCHOTTKY
DIODES:
HSMS2822
Figure 60. Transformer-Coupled Differential Clock (Up to 200 MHz)
Drive the SYNC input using a single-ended CMOS type signal.
If not used, connect the SYNC pin to ground.
25Ω
ADC
390pF
1nF
390pF
390pF
CLOCK
INPUT
CLK+
Clock Duty Cycle
Typical high speed ADCs use both clock edges to generate a
variety of internal timing signals and, as a result, may be
sensitive to clock duty cycle. Commonly, a 5% tolerance is
required on the clock duty cycle to maintain dynamic
performance characteristics.
CLK–
SCHOTTKY
DIODES:
25Ω
HSMS2822
Figure 61. Balun-Coupled Differential Clock (Up to 1240 MHz)
If a low jitter clock source is not available, another option is to
ac couple a differential PECL signal to the sample clock input
pins as shown in Figure 62. The AD9510, AD9511, AD9512,
AD9513, AD9514, AD9515, AD9516-5, AD9517-1, AD9518-1,
AD9520-5, AD9522-1, AD9523, AD9524, and ADCLK905/
ADCLK907/ADCLK925 clock drivers offer excellent jitter
performance.
The AD9652 contains a clock DCS that retimes the nonsampling
(falling) edge, providing an internal clock signal with a nominal
50% duty cycle. This allows the user to provide a wide range of
clock input duty cycles without affecting the performance of the
AD9652.
Jitter on the rising edge of the input clock is still of paramount
concern and is not reduced by the duty cycle stabilizer. The
DCS control loop does not function for clock rates less than
80 MHz nominally. The loop has a time constant associated
with it that must be considered when the clock rate changes
dynamically. A wait time of 1.5 μs to 5 μs is required after a
dynamic clock frequency increase or decrease before the DCS
loop is relocked to the input clock. During that time period, the
loop is not locked, the DCS loop is bypassed, and internal
ADC
0.1µF
0.1µF
CLOCK
INPUT
CLK+
AD95xx
PECL DRIVER
100Ω
0.1µF
0.1µF
CLOCK
INPUT
CLK–
240Ω
240Ω
50kΩ
50kΩ
Figure 62. Differential PECL Sample Clock (Up to 1240 MHz)
Rev. B | Page 24 of 36
Data Sheet
AD9652
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
2.5
device timing is dependent on the duty cycle of the input clock
signal. In some cases, it may be appropriate to disable the duty
cycle stabilizer, for example, if a high quality RF clock is
available to drive the AD9652 clock input and does not need
adjustment in duty cycle correction. In most other applications,
enabling the DCS circuit is recommended to maximize ac
performance.
AVDD3
AVDD_CLK
DRVDD/SPIVDD
AVDD
2.0
1.5
1.0
0.5
0
POWER
Jitter Considerations
High speed, high resolution ADCs are sensitive to the quality
of the clock input. The degradation in SNR at a given input
frequency (fIN) due to jitter (tJ) can be calculated by
SNRHF = −10 log[(2π × fIN × tJRMS)2 + 10 (SNR /10)
]
LF
80
130
180
230
280
SAMPLE RATE (MSPS)
In the equation, the rms aperture jitter represents the root-
mean-square of all jitter sources, which includes the clock
input, the analog input signal, and the ADC aperture jitter
specification. IF undersampling applications are particularly
sensitive to jitter, as shown in Figure 64.
Figure 65. Power and Current vs. Sample Rate
By asserting power-down (either through setting Register 0x08
or by asserting the PDWN pin high), the AD9652 is placed in
power-down mode. In this state, the ADC typically dissipates
less than 1 mW. During power-down, the output drivers are
placed in a high impedance state. Deasserting the PDWN pin
(forcing it low) returns the AD9652 to its normal operating
mode. Note that the level on PDWN is referenced to the digital
output driver supply (DRVDD) and cannot exceed that supply
voltage.
80
78
76
74
72
70
68
Low power dissipation in power-down mode is achieved by
shutting down the reference, reference buffer, biasing networks,
and clock. Internal capacitors are discharged when entering
power-down mode and then must be recharged when returning
to normal operation. As a result, wake-up time is related to the
time spent in power-down mode, and shorter power-down
cycles result in proportionally shorter wake-up times.
66
MEASURED
0.8ps
0.2ps
64
0.1ps
0.05ps
62
0.05ps
60
5
50
500
fIN (MHz)
When using the SPI port interface, the user can place the ADC
in power-down mode or standby mode. Standby mode allows
the user to keep the internal reference circuitry powered when
faster wake-up times are required. See the AN-877 Application
Note, Interfacing to High Speed ADCs via SPI, for additional
details.
Figure 64. SNRFS vs. Input Frequency and Jitter
Treat the clock input as an analog signal in cases where aperture
jitter may affect the dynamic range of the AD9652.
Drive external clock sources and buffers from a clean ADC
output driver supply to avoid modulating the ADC clock with
noise. Low jitter, crystal controlled oscillators make the best
clock sources. If the clock is generated from another type of
source (by gating, dividing, or another method), retime it by the
original clock at the last step.
INTERNAL BACKGROUND CALIBRATION
The AD9652 uses a background calibration to continually correct
errors between internal analog circuits to maintain the high
level of noise performance over varying conditions. The calibration
correction digitally monitors the errors in the various analog
blocks, calculates the error, and applies corrections. The back-
ground correction is calculated every 3 × 233 samples; therefore,
when running at 310 MSPS, the update rate is about 83 seconds.
Each calibration cycle is independent from previous calibrations to
improve tracking. There are no requirements on the input signal
for the background calibration.
Refer to the AN-501 Application Note, Aperture Uncertainty
and ADC System Performance, and the AN-756 Application
Note, Sampled Systems and the Effects of Clock Phase Noise and
Jitter, for more information about jitter performance as it relates
to ADCs.
POWER DISSIPATION AND STANDBY MODE
As shown in Figure 65, the power dissipated by the AD9652 is
proportional to its sample rate. The data in Figure 65 was taken
using the same operating conditions as those used for the
Typical Performance Characteristics section.
The calibration occurs independently for each ADC path. The
background calibration continually operates but does not
update if the input signal is significantly out of range (beyond
the OTR) because this can cause errors in the calibration
calculation.
Rev. B | Page 25 of 36
AD9652
Data Sheet
Although this is not recommended, in some instances such as
when all the environmental, clocking, and input signals are very
stable, the calibration can be paused. Pausing the background
calibration causes a slight degradation in performance, but can
be accomplished by writing 0x1 to Register 0x4FB, Bit 0 . To re-
enable the background calibration, write 0x0 to Register 0x4FB,
Bit 0. Note: Register 0x4FB has reserved bits that must be
preserved when accessing that and similar registers.
The calibration engine monitors any errors and resets the
calibration cycle if the input signal exceeds the input range for
1000 samples within a single calibration cycle.
At startup, when the AD9652 is first powered and a valid clock
is applied, a fast start-up background calibration is performed
and converges 64 times faster than the normal calibration cycle.
At 310 MSPS, the fast start-up calibration updatesafter 1.3 seconds.
The fast start-up calibration allows the AD9652 to be used
sooner than waiting for a full calibration cycle and typically
degrades SNR performance by less than 0.5 dB. This degradation
lasts until a full calibration cycle completes.
DIGITAL OUTPUTS
The AD9652 output drivers are for standard ANSI LVDS, but
optionally the drive current can be reduced using Register 0x15.
The reduced drive current for the LVDS outputs potentially
reduce the digitally induced noise.
In cases where configuration of the AD9652 changesand a
recalibration is needed, a fast start-up calibration can be
initiated by an SPI register write or by asserting and
deasserting the PDWN pin.
As detailed in the AN-877 Application Note, Interfacing to High
Speed ADCs via SPI, the data format can be selected for offset
binary, twos complement, or gray code when using the SPI
control.
To initiate using the SPI register, use Register 0x08[1:0]. To start
a new fast calibration, put either or both ADC channels in
standby and then return them to normal operation mode by
writing 0x2 and then 0x0 to Register 0x08[1:0]. After returning
to normal operation mode, the fast calibration is initiated one
time followed by the normal, full calibration cycle. In addition
to standby, this is also the case for power-down. Writing a 0x1
followed by a 0x0 initiates a fast calibration. Alternatively, a fast
start-up calibration can be initiated by writing 0x0C and then
0x08 to Register 0x4FB.
The AD9652 has a flexible three-state ability for the digital
output pins. The three-state mode is enabled when the device is
set for power-down mode.
Timing
The AD9652 provides latched data with a pipeline delay of
26 input sample clock cycles. Data outputs are available one
propagation delay (tPD) after the rising edge of the clock signal.
Minimize the length of the output data lines and the corresponding
loads to reduce transients within the AD9652. These transients
can degrade converter dynamic performance.
The PDWN pin can be configured to put the device in power-
down or standby mode based on the setting in Register0x08[1:0].
Transitioning from either power-down or standby into normal
mode causes a fast calibration to be initiated. Configuration
changes that require a new calibration include, but are not
limited to, changes of setting for VREF, dither enable/disable,
clock input changes, and DCS state changes.
The lowest typical conversion rate of the AD9652 is 80 MSPS.
At clock rates below 80 MSPS, dynamic performance may
degrade.
Data Clock Output
There are various advanced configuration options associated
with the background calibration for applications that require
special treatment. The options include an optional recovery
mode for standby and a pausing background calibration.
The AD9652 also provides a data clock output (DCO) intended
for capturing the data in an external register. Figure 2 shows a
timing diagram of the AD9652 output modes. The DCOrelative to
the data output can be adjusted using Register 0x17. There are 32
delay settings with approximately 81 ps per step. Data is output
in a DDR format and is aligned to the rising and falling edges of
the clock derived from DCO .
If standby is used in an application, by default, the AD9652
keeps the current corrections, but initiates a new fast calibration
when returning to normal operation mode. For standby, if
conditions have not significantly changed, the AD9652 can be
configured to retain the last correction coefficients by writing
0x00 to Register 0x4FA before entering the standby mode. This
returns the device to the same operation as when it entered
standby, retaining previous calibration values in standby mode
and continuing the normal calibration cycle when returned to
normal operation mode.
ADC OVERRANGE
The ADC overrange (OR) indicator is asserted when an
overrange is detected on the input of the ADC. The overrange
condition is determined at the output of the ADC pipeline and,
therefore, is subject to a latency of 26 ADC clocks. An
overrange at the input is indicated by this bit, 26 clock cycles
after it occurs.
Rev. B | Page 26 of 36
Data Sheet
AD9652
Table 13. Output Data Format
Differential Input Voltage (V):
(VIN+x) – (VIN–x)
Input Span = 2.5 V p-p (V)
Offset Binary Output Mode
00 0000 0000 0000
00 0000 0000 0000
10 0000 0000 0000
11 1111 1111 1111
11 1111 1111 1111
Twos Complement Mode (Default)
10 0000 0000 0000
OR Pin Logic Level
<–1.25
–1.25
0
+1.25
>+1.25
1
0
0
0
1
10 0000 0000 0000
00 0000 0000 0000
01 1111 1111 1111
01 1111 1111 1111
Rev. B | Page 27 of 36
AD9652
Data Sheet
FAST THRESHOLD DETECTION (FDA/FDB)
In receiver applications, it is desirable to have a mechanism to
reliably determine when the converter is about to be clipped. The
standard overflow indicator on the OR pins provide delayed
information, which is synchronized with the output data. The
delayed indicator is of limited value in preventing clipping in this
case. Therefore, it is helpful to have a programmable threshold
below full scale that allows time to reduce external gain before the
clip occurs. In addition, because input signals can have significant
slew rates, latency of this function is of concern.
The selected threshold register is compared with the signal
magnitude at the output of the ADC. The fast upper threshold
detection has a latency of seven clock cycles. The approximate
upper threshold is a 4-bit value defined by
Upper Threshold (% Full Scale) =
((Register 0x47 value)/8) × 100%
The FD indicators are not cleared until the signal drops below
the lower threshold for the programmed dwell time. The lower
threshold is programmed in the fast detect lower threshold
registers, Register 0x49 and Register 0x4A. The fast detect lower
threshold register is a 15-bit register that is compared with the
signal magnitude at the output of the ADC. This comparison is
subject to the ADC pipeline latency but is accurate in terms of
converter resolution. The lower threshold is defined by
Using the SPI port, the user can provide a threshold above
which the fast detect (FD) output is active. Bit 0 of Register 0x45
enables the FD feature. Register 0x47 to Register 0x4C allow the
user to set the threshold levels and timing. As long as the signal
is below the selected threshold, the FD output remains low. In
this mode, the magnitude of the data is considered in the calcu-
lation of the condition, but the sign of the data (either positive
or negative) is not considered. The threshold detection responds
identically to positive and negative signals outside the desired
range (magnitude).
Lower Threshold (% Full Scale) =
((Register 0x49/Register 0x4A value)/32767) × 100%
For example, to set an upper threshold of 50% full scale, write
0x04 to Register 0x47, and to set a lower threshold of 40% full
scale, write 0x3333 to Register 0x49 and Register 0x4A.
The fast detect indicators, FDA for Channel A and FDB for
Channel B, are asserted when the input magnitude exceeds the
value programmed in the fast detect upper threshold register,
Register 0x47.
The dwell time can be programmed from 1 sample clock cycle
to 65,535 sample clock cycles by placing the desired value in the
fast detect dwell time registers, Register 0x4B and Register 0x4C
(see Figure 66).
UPPER THRESHOLD
DWELL TIME
TIMER RESET BY
RISE ABOVE
LOWER
THRESHOLD
LOWER THRESHOLD
TIMER COMPLETES BEFORE
SIGNAL RISES ABOVE
LOWER THRESHOLD
DWELL TIME
FDA OR FDB
Figure 66. Threshold Settings for FDA and FDB Signals
Rev. B | Page 28 of 36
Data Sheet
AD9652
SERIAL PORT INTERFACE
The AD9652 serial port interface (SPI) allows the user to
configure the converter for specific functions or operations
through a structured register space provided inside the ADC.
The SPI gives the user added flexibility and customization,
depending on the application. Addresses are accessed via the
serial port and can be written to or read from via the port.
Memory is organized into bytes that can be further divided into
fields. These fields are documented in the Memory Map
section. For detailed operational information, see the AN-877
Application Note, Interfacing to High Speed ADCs via SPI.
In addition to word length, the instruction phase determines
whether the serial frame is a read or write operation, allowing
the serial port to be used both to program the chip and to read
the contentsof the on-chip memory. If the instruction is a readback
operation, performing a readback causes the serial data input/
output (SDIO/DCS) pin to change direction from an input to an
output at the appropriate point in the serial frame.
Data can be sent in MSB first mode or in LSB first mode. MSB
first is the default on power-up and can be changed via the SPI
port configuration register. For more information about this
and other features, see the AN-877 Application Note.
CONFIGURATION USING THE SPI
Three pins define the SPI of this ADC: the SCLK pin, the SDIO
pin, and the CSB pin (see Table 14). The SCLK (serial clock) pin
synchronizesthe read and write datapresented from/to the ADC.
The SDIO (serial data input/output) pin is a dual-purpose pin
that allows data to be sent and read from the internal ADC
memory map registers. The CSB (chip select bar) pin is an
active low control that enables or disables the read and write cycles.
HARDWARE INTERFACE
The pins described in Table 14 comprise the physical interface
between the user programming device and the serial port of the
AD9652. The SCLK pin and the CSB pin function as inputs
when using the SPI interface. The SDIO pin is bidirectional,
functioning as an input during write phases and as an output
during readback.
Table 14. Serial Port Interface Pins
The SPI interface is flexible enough to be controlled by either
field-programmable grid arrays (FPGAs) or microcontrollers.
One method for SPI configuration is described in detail in the
AN-812 Application Note, Microcontroller-Based Serial Port
Interface (SPI) Boot Circuit.
Pin
Function
SCLK Serial clock. Theserial shift clockinput, which synchronizes
serial interface reads and writes.
SDIO Serial data input/output. A dual-purpose pin that
typically serves as an input or an output, depending on
the instruction being sent and the relative position in the
timingframe.
The SPI port must not be active during periods when the full
dynamic performance of the converter is required. Because the
SCLK signal, the CSB signal, and the SDIO signal are typically
asynchronous to the ADC clock, noise from these signals can
degrade converter performance. If the on-board SPI bus is used
for other devices, itmaybe necessary toprovide buffers between
this bus and the AD9652 to prevent these signals from transi-
tioning at the converter inputs during critical sampling periods.
Chip select bar. An active low control that gates the read
and write cycles. Must be pulledto logic high during
power up.
CSB
The falling edge of CSB, in conjunction with the rising edge of
SCLK, determines the start of the framing. An example of the
serial timing and its definitions can be found in Table 5 and
Figure 4.
CONFIGURATION WITHOUT THE SPI
In applications that do not interface to the SPI control registers,
the SDIO pin and the SCLK pin serve as standalone CMOS-
compatible control pins. When the device is powered up, it is
assumed that the user intends to use the pins as static control
lines for the DCS and output data format feature control. In this
mode, connect CSB to AVDD, which disables the serial port
interface.
Other modes involving the CSB pin are available. The CSB pin
can be held low indefinitely, which permanently enables the
device; this is called streaming. The CSB pin can stall high
between bytes to allow for additional external timing. When
CSB is tied high, SPI functions are placed in a high impedance
mode.
During an instruction phase, a 16-bit instruction is transmitted.
Data follows the instruction phase, and its length is determined
by the W0 and the W1 bits.
Table 15. Mode Selection
Pin
External Voltage
AVDD (default)
AGND
Configuration
SDIO
DCSenabled
All data is composed of 8-bit words. The first bit of each
individual byte of serial data indicates whether a read or write
command is issued. This allows the serial data input/output
(SDIO) pin to change direction from an input to an output.
DCS disabled
SCLK
AVDD
AGND (default)
Twos complementenabled
Offset binary enabled
Rev. B | Page 29 of 36
AD9652
Data Sheet
SPI ACCESSIBLE FEATURES
Table 16 provides a brief description of the general features that
are accessible via the SPI. These features are described in detail
in the AN-877 Application Note.
Table 16. Features AccessibleUsing the SPI
Feature Name
Power Modes
Clock
Description
Allows the user toset eitherpower-down mode or standby mode
Allows the user to access the DCS via the SPI
Allows the user to digitally adjust the converter offset
Allows the user to set test modes to have known data on output bits
Allows the user to set up outputs
Allows the user to set theoutputclock polarity
Allows the user to vary the delay of the clock derived from DCO
Allows the user to set the reference voltage
Offset
Te st I/O
Output Mode
Output Phase
Output Delay
VREF
Rev. B | Page 30 of 36
Data Sheet
AD9652
MEMORY MAP
LogicLevels
READING THE MEMORY MAP REGISTER TABLE
An explanation of logic level terminology follows:
Each row in the memory map register table has eight bit
locations. The memory map is roughly divided into three
sections: the chip configuration registers (Address 0x00 to
Address 0x02); the channel index and transfer registers
(Address 0x05 and Address 0xFF); and the ADC functions
registers, including setup, control, and test (Address 0x08 to
Address 0x4FB).
•
“Bit is set” is synonymous with “bit is set to Logic 1” or
“writing Logic 1 for the bit.”
•
“Clear a bit” is synonymous with “bit is set to Logic 0” or
“writing Logic 0 for the bit.”
Transfer Register Map
The 0x08, 0x09, 0x0B, 0x0D, 0x0F, 0x10, 0x14, 0x16, 0x17, and
0x30 registers are shadowed. Writes to these addresses do not
affect device operation until a transfer command is issued by
writing 0x01 toAddress0xFF, setting the transfer bit. This allows
these registers to be updated internally and simultaneously when
the transfer bit is set. The internal update occurs when the
transfer bit is set, and then the bit autoclears.
The memory map register table (see Table 17) documents the
default hexadecimal value for each hexadecimal address shown.
The column with the heading Bit 7 (MSB) is the start of the
default hexadecimal value given. For example, Address 0x09,
the global clock register, has a hexadecimal default value of
0x01. This means thatthe LSB or Bit 0 = 1, and the remaining
bits are 0s. This setting is the default output format value, which
is twos complement. For more information on the functions
controlled by Register 0x00 to Register 0x17, see the AN-877
Application Note. This application note also details the
functions controlled by all remaining registers.
Channel SpecificRegisters
Some channel setup functions, such as the signal monitor
thresholds, can be programmed to a different value for each
channel. In these cases, channel address locations are internally
duplicated for each channel. These registers and bits are designated
in Table 17 as local. These local registers and bits can be accessed
by setting the appropriate Channel A or Channel B bits in
Register 0x05. If both bits are set, the subsequent write affects
the registers of both channels. In a read cycle, only Channel A
or Channel B are set to read one of the two registers. If both bits
are set during an SPI read cycle, the device returns the value for
Channel A. Registers and bits designated as global in Table 17
affect the entire device and the channel features for which
independentsettings are notallowed. The settings in Register 0x05
do not affectthe globalregisters and bits.
Open and Reserved Locations
All address and bit locations that are not included in Table 17
are not currently supported for this device. Unused bits of a
valid address location must be written with 0s, unless otherwise
noted. Writing to these locations is required only when part of
an address location is open (for example, Address 0x18). If the
entire address location is open/unused/undocumented (for
example, Address 0x13), this address location must not be written.
Default Values
After the AD9652 is reset, critical registersare loaded with
default values. The default values for the registers are given in
the memory map register table, Table 17.
Rev. B | Page 31 of 36
AD9652
Data Sheet
MEMORY MAP REGISTER TABLE
All address and bit locations that are not included in Table 17 are not currently supported for this device.
Table 17. Memory Map Registers
Default
Default
Addr
(Hex)
Register
Name
Bit 7
(MSB)
Bit 0
(LSB)
Value
(Hex)
Notes/
Comments
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Chip Configuration Registers
0x00
SPI port
0
LSB first
Soft reset
1
1
Soft reset
LSB first
0
0x18
The nibbles
are mirrored
so that LSB
first mode
or MSB first
mode
config-
uration
(global)1
registers
correctly,
regardless
of shift
mode
0x01
0x02
Chip ID
(global)
8-Bit Chip ID[7:0], (AD9652 = 0xC1) (default)
0xC1
0x00
Read only
Chip grade
(global)
Speed grade ID,
0x00: default
Speed
grade ID
differ-
entiates
devices;
read only
Channel Index and Transfer Registers
0x05
Channel
index
Channel B Channel A 0x03
(default) (default)
Bits are
set to
(global)
determine
which
device on
the chip
receives
the next
write
command;
applies to
local
registers
only
0xFF
Transfer
(global)
Transfer
0x00
Synchro-
nously
transfers
data from
the master
shift register
to the slave
ADC Functions
0x08 Power
Reserved,
set to 1
External
power-
down pin
function
(local)
0 =
Internal power-down
mode (local)
00 = normal operation
01 = full power-down
10 = standby
0x80
Controls
power-
down
modes
(local)
options
11 = reserved
power-
down
1 =
standby
0x09
Global clock
(global)
Enable
DCS
0x01
(default)
Rev. B | Page 32 of 36
Data Sheet
AD9652
Default
Value
(Hex)
Default
Notes/
Comments
Addr
(Hex)
Register
Name
Bit 7
(MSB)
Bit 0
(LSB)
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
0x0B
Clock divide
(global)
Clock divide ratio
000 = divide by 1
001 = divide by 2
0x00
010 = reserved, do not use
011 = divide by 4
100 = divide by 8
0x0D
Test mode
(local)
Reset PN23 Reset
Output test mode
0000 = off (default)
0001 = midscale short
0010 = positive FS
0011 = negative FS
0x00
When this
long gen
PN23:
PN9
short gen
PN9:
register is
set, the test
data is
placed on
the output
pins (D0
1 +x17
x22
+
1 + x3 + x8
0100 = alternating checkerboard
0101 = PN23 long sequence
0110 = PN9 short sequence
0111 = one/zero word toggle
to D15 ) in
place of
normal data
0x0F
Common-
Enable
0x00
mode servo
(global)
common-
mode
servo
0x10
0x14
Offset adjust
(local)
Offset adjust in LSBs from +127 (0111 1111) to −128 (1000 0000)
(twos complement format)
0x00
0x00
Output
Output format
Configures
mode (local)
00 = offset binary
(default)
the outputs
and the
01 = twos complement
10 = gray code
format of
the data
11 = reserved
0x15
Output
LVDS
control
LVDS output drive current adjust
000 = 3.72 mA (ANSI-LVDS,
default)
0x00
(global)
001 = 3.50 mA
010 = 3.30 mA
011 = 2.96 mA
100 = 2.82 mA
101 = 2.57 mA
110 = 2.27 mA
111 = 2.00 mA (reduced swing
LVDS)
0x16
Clock phase
adjust
Input clock divider phase adjust
000 = no delay
0x00
(global)
001 = 1 input clock cycle
010 = 2 input clock cycle
011 = 3 input clock cycle
100 = 4 input clock cycle
101 = 5 input clock cycle
110 = 6 input clock cycle
111 = 7 input clock cycle
0x17
DCO
DCO clock delay
0x00
(Delay = (2500 ps × register value/31))
output delay
(global)
00000 = 0 ps
00001 = 81 ps
00010 = 161 ps
…
11110 = 2419 ps
11111 = 2500 ps
0x18
0x30
Input span
select
(global)
Reserved, Reserved,
set to 1 set to 1
VREF select
000 = 1.25 V (2.5 V p-p input), default
001 = 1.125 V (2.25 V p-p input)
0xC0
0x00
010 = 1.20 V (2.4 V p-p input)
011 = 1.25 V (2.5 V p-p input)
100 = do not use
101 = 1.0 V (2.0 V p-p input)
Dither (local)
Dither
enable
Rev. B | Page 33 of 36
AD9652
Data Sheet
Default
Default
Addr
(Hex)
Register
Name
Bit 7
(MSB)
Bit 0
(LSB)
Value
(Hex)
Notes/
Comments
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
0x45
Fast detect
(FD) control
Enable
fast
detect
output
0x00
0x08
0x47
FD upper
threshold
Fast Detect Upper Threshold[3:0]
Valid programming range = 0x1 to 0x8
Threshold = midscale (register value) × (1/8) ×
(full scale)
0x49
0x4A
0x4B
0x4C
0x100
FD lower
threshold
Fast Detect Lower Threshold[7:0]
Fast Detect Lower Threshold[14:8]
Fast Detect Dwell Time[7:0]
0x00
0x02
0x00
0x08
0x00
FD lower
threshold
FD dwell
time
FD dwell
time
Fast Detect Dwell Time[15:8]
SYNC
control
(global)
Clock
divider
next SYNC
only
Clock
divider
SYNC
enable
Master
SYNC
buffer
enable
0x212
Dither gain
(global)
0b0000: 100% dither applied
0b0001: 99.6% dither applied
0b0010: 99.2% dither applied
0b0011: 98.4% dither applied
0b0100: 96.8% dither applied
0b0101: 93.75% dither applied
0b0110: 87.5% dither applied
0b0111: 75% dither applied
0b1000: 50% dither applied
Reserved, Reserved,
set to 0 set to 0
Reserved, Reserved,
set to 0 set to 0
0x08
0x22A Input
frequency
0: fIN in 1st Nyquist
0x00
0x03
1: fIN in 2nd Nyquist
2: fIN in 3rd Nyquist or
higher
settings
(global)
0x4FA
Calibration
power-
down
Reserved, Reserved,
set to 0 set to 0
Reserved,
set to 0
Reserved, Reserved, Reserved,
set to 0 set to 0 set to 0
Power down/standby
initial calibration
action:
config-
uration
(global)
0b00: use previous
calibration correction
0b11: initiate a fast
calibration
0x4FB
Calibration
power-down
configura-
Reserved, Reserved,
set to 0 set to 0
Reserved,
set to 0
Reserved, Reserved, Reset
Reserved,
set to 0
Pause
back-
ground
0x08
set to 0
set to 1
back-
ground
tion (global)
calibration
calibration,
set high
then low
1 Set the channel index register at Address 0x05to 0x03 (default)whenwriting to Address 0x00.
Rev. B | Page 34 of 36
Data Sheet
AD9652
APPLICATIONS INFORMATION
VCM
DESIGN GUIDELINES
The VCM pin must be decoupled to ground with a 0.1 μF
capacitor, as shown in Figure 54. For optimalchannel-to-channel
isolation, a 33 Ω resistor must be included between the AD9652
VCM pin and the Channel A analog input network connection,
as well as between the AD9652 VCM pin and the Channel B
analog input network connection.
Before starting system level design and layout of the AD9652, it
is recommended that the designer become familiar with these
guidelines, which describes the special circuit connections and
layout requirements needed for certain pins.
Powerand Ground Recommendations
When connecting power to the AD9652, it is recommended that
three separate power supplies be used. AVDD3 requires a 3.3 V
supply, AVDD_CLK and AVDD require a 1.8 V supply, and
DRVDD requiresa 1.8 V supply. SPIVDD is typically connected
to the same supply as DRVDD, but can be connected to a separate
supply between 1.8 V and 3.3 V to ease the interface to the logic
device that connects to the SPI pins (CLK, SDIO, and CSB).
RBIAS
The AD9652 requires that a 10 kΩ resistor be placed between
the RBIAS pin and ground. This resistor sets the master current
reference of the ADC core and must have at leasta 1%tolerance.
ReferenceDecoupling
Decouple the VREF pin externally to ground with a low ESR,
1.0 μF capacitor in parallel with a low ESR, 0.1 μF ceramic
capacitor.
The AVDD3 supply must be supplied from a clean 3.3 V power
source. Decoupling must be a combination of PCB plane
capacitance and decoupling capacitors to cover both high and low
frequency noise sources. Typical capacitors of 0.1 μF and 1 μF
near the AD9652 AVDD3 pins are advised.
SPI Port
The SPI port must not be active during periods when the full
dynamic performance of the converter is required. Because the
SCLK, CSB, and SDIO signals are typically asynchronous to the
ADC clock, noise from these signals can degrade converter
performance. If the on-board SPI bus is used for other devices,
it may be necessary to provide buffers between this bus and the
AD9652 to keep these signals from transitioning at the converter
input pins during critical sampling periods.
The AVDD and AVDD_CLK supply connection must be
powered up simultaneously to achieve proper on-chip biasing;
therefore, it is recommended to connect the two supply voltages
to a single source. Similar to the AVDD3 supply, decoupling must
be a combination of PCB plane capacitance and decoupling
capacitors to cover both high and low frequency noise sources.
Typical capacitorsof 0.1 μF and 1 μF near the AD9652 AVD D
and AVDD_CLK pins is advised.
The DRVDD and SPIVDD supply connection must also have
decoupling but these can be placed slightly further away from
the AD9652. DRVDD and SPIVDD can be tied together for
applications that can use a 1.8 V SPI interface logic. Optionally,
SPIVDD can be driven with a supply of up to 3.3 V to support
higher voltage logic interfaces.
Multiple large area PCB ground planes are recommended and
provide many benefits. Low impedance power and ground
planes are needed to maintain performance. Stacking power and
ground planes in the PCB provides high frequency decoupling.
Ground planes and thermal vias help dissipate heat generated
by the device. With proper decoupling and smart partitioning
of the PCB analog, digital, and clock sections, optimum
performance is easily achieved.
Rev. B | Page 35 of 36
AD9652
Data Sheet
OUTLINE DIMENSIONS
10.10
10.00 SQ
9.90
A1 BALL
CORNER
A1 BALL
CORNER
12 11 10
9
7 4 1
8 6 5 3
2
A
B
C
D
E
F
8.80
BSC SQ
G
H
J
0.80
BSC
K
L
M
BOTTOM VIEW
DETAIL A
TOP VIEW
0.60 REF
1.11
1.01
0.91
DETAIL A
1.40
1.34
1.19
0.33 NOM
0.28 MIN
*
0.50
0.45
0.40
COPLANARITY
0.12
SEATING
PLANE
BALL DIAMETER
*
COMPLIANT WITH JEDEC STANDARDS MO-275-EEAA-1
WITH THE EXCEPTION TO BALL DIAMETER.
Figure 67. 144-Ball Chip Scale Package Ball Grid Array [CSP_BGA]
(BC-144-6)
Dimensions shown in millimeters
ORDERING GUIDE
Model1
Temperature Range
Package Description
Package Option
BC-144-6
BC-144-6
AD9652BBCZ-310
AD9652BBCZRL7-310
AD9652-310EBZ
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
144-Ball Chip Scale Package Ball Grid Array [CSP_BGA]
144-Ball Chip Scale Package Ball Grid Array [CSP_BGA]
Evaluation Board with AD9652
1 Z = RoHS Compliant Part.
©2014–2017 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D12169-0-1/17(B)
Rev. B | Page 36 of 36
相关型号:
©2020 ICPDF网 联系我们和版权申明