AD9741-EBZ [ADI]
Dual 8-/10-/12-/14-/16-Bit 250 MSPS Digital-to-Analog Converters; 双8位/ 10位/ 12位/ 14位/ 16位250 MSPS数字 - 模拟转换器
| 型号： | AD9741-EBZ |
| 厂家： | 
ADI |
| 描述： | Dual 8-/10-/12-/14-/16-Bit 250 MSPS Digital-to-Analog Converters |
| 文件： | 总28页 (文件大小：649K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Dual 8-/10-/12-/14-/16-Bit
250 MSPS Digital-to-Analog Converters
AD9741/AD9743/AD9745/AD9746/AD9747
FEATURES
GENERAL DESCRIPTION
High dynamic range, dual DACs
Low noise and intermodulation distortion
The AD9741/AD9743/AD9745/AD9746/AD9747 are pin-
compatible, high dynamic range, dual digital-to-analog
Single carrier WCDMA ACLR = 80 dBc @ 61.44 MHz IF
Innovative switching output stage permits useable outputs
beyond Nyquist frequency
LVCMOS inputs with dual-port or optional interleaved
single-port operation
Differential analog current outputs are programmable from
8.6 mA to 31.7 mA full scale
Auxiliary 10-bit current DACs with source/sink capability for
external offset nulling
converters (DACs) with 8-/10-/12-/ 14-/16-bit resolutions
and sample rates of up to 250 MSPS. The devices include
specific features for direct conversion transmit applications,
including gain and offset compensation, and they interface
seamlessly with analog quadrature modulators, such as the
ADL5370.
A proprietary, dynamic output architecture permits synthesis
of analog outputs even above Nyquist by shifting energy away
from the fundamental and into the image frequency.
Internal 1.2 V precision reference voltage source
Operates from 1.8 V and 3.3 V supplies
315 mW power dissipation
Full programmability is provided through a serial peripheral
interface (SPI) port. In addition, some pin-programmable
features are offered for those applications without a controller.
Small footprint, Pb-free, 72-Lead LFCSP
PRODUCT HIGHLIGHTS
APPLICATIONS
1. Low noise and intermodulation distortion (IMD) enables
high quality synthesis of wideband signals.
Wireless infrastructure:
WCDMA, CDMA2000, TD-SCDMA, WiMAX
Wideband communications:
LMDS/MMDS, point-to-point
Instrumentation:
2. Proprietary switching output for enhanced dynamic
performance.
3. Programmable current outputs and dual auxiliary DACs
provide flexibility and system enhancements.
RF signal generators, arbitrary waveform generators
FUNCTIONAL BLOCK DIAGRAM
CLKP
CLKN
IOUT1P
16-BIT
DAC1
IOUT1N
INTERFACE LOGIC
10
IOUT2P
16-BIT
PID<15:0>
DAC2
IOUT2N
GAIN
DAC
CMOS
INTERFACE
GAIN
DAC
AUX1P
OFFSET
INTERNAL
REFERENCE
AND
P2D<15:0>
DAC
AUX1N
SERIAL
PERIPHERAL
INTERFACE
AUX2P
OFFSET
DAC
BIAS
AUX2N
Figure 1.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
©2007 Analog Devices, Inc. All rights reserved.
AD9741/AD9743/AD9745/AD9746/AD9747
TABLE OF CONTENTS
Features .............................................................................................. 1
Instruction Byte.......................................................................... 18
MSB/LSB Transfers .................................................................... 19
Serial Interface Port Pin Descriptions ..................................... 19
SPI Register Map ............................................................................ 20
SPI Register Descriptions.............................................................. 21
Digital Inputs and Outputs ........................................................... 22
Input Data Timing ..................................................................... 22
Dual-Port Mode Timing ........................................................... 22
Single-Port Mode Timing ......................................................... 22
SPI Port, Reset, and Pin Mode.................................................. 22
Driving the DAC Clock Input .................................................. 23
Full-Scale Current Generation ................................................. 23
DAC Transfer Function............................................................. 24
Analog Modes of Operation ..................................................... 24
Auxiliary DACS.......................................................................... 25
Power Dissipation....................................................................... 25
Outline Dimensions....................................................................... 27
Ordering Guide .......................................................................... 27
Applications....................................................................................... 1
General Description......................................................................... 1
Product Highlights ........................................................................... 1
Functional Block Diagram .............................................................. 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
DC Specifications ......................................................................... 3
AC Specifications.......................................................................... 5
Digital and Timing Specifications.............................................. 7
Absolute Maximum Ratings............................................................ 8
Thermal Resistance ...................................................................... 8
ESD Caution.................................................................................. 8
Pin Configurations and Function Descriptions ........................... 9
Typical Performance Characteristics ........................................... 14
Terminology .................................................................................... 17
Theory of Operation ...................................................................... 18
Serial Peripheral Interface......................................................... 18
General Operation of the Serial Interface............................... 18
REVISION HISTORY
5/07—Revision 0: Initial Version
Rev. 0 | Page 2 of 28
AD9741/AD9743/AD9745/AD9746/AD9747
SPECIFICATIONS
DC SPECIFICATIONS
TMIN to TMAX, AVDD33 = 3.3 V, DVDD33 = 3.3 V, DVDD18 = 1.8 V, CVDD18 = 1.8 V, IFS = 20 mA, full-scale digital input, maximum
sample rate, unless otherwise noted.
Table 1. AD9741, AD9743, and AD9745
AD9741
Min Typ
AD9743
Max Min Typ
10
AD9745
Max Min Typ
12
Parameter
Unit
Max
RESOLUTION
8
Bits
ACCURACY
Differential Nonlinearity (DNL)
Integral Nonlinearity (INL)
MAIN DAC OUTPUTS
Offset Error
0.03
0.0ꢀ
0.0ꢀ
0.10
0.13
0.2ꢀ
LSB
LSB
0.001
0.001
0.001
%FSR
Offset Error Temperature Coefficient
Gain Error
1.0
2.0
100
1.0
1.0
1.0
ppm/°C
%FSR
ppm/°C
%FSR
2.0
100
1.0
2.0
100
1.0
Gain Error Temperature Coefficient
Gain Matching (DAC1 to DAC2)
Full-Scale Output Current
Output Compliance Voltage
Output Resistance
8.6
−1.0
31.7 8.6
+1.0 −1.0
31.7 8.6
+1.0 −1.0
31.7 mA
+1.0
V
MΩ
10
10
10
10
10
10
AUXILIARY DAC OUTPUTS
Resolution
Bits
Full-Scale Output Current
Output Compliance Voltage Range—Sink Current
Output Compliance Voltage Range—Source Current
Output Resistance
−2.0
0.8
0
+2.0 −2.0
+2.0 −2.0
+2.0 mA
1.6
1.6
0.8
0
1.6
1.6
0.8
0
1.6
1.6
V
V
1
1
1
MΩ
Bits
Monotonicity
10
10
10
REFERENCE INPUT/OUTPUT
Output Voltage
1.2
10
1.2
10
1.2
10
V
Output Voltage Temperature Coefficient
External Input Voltage Range
Input or Output Resistance
POWER SUPPLY VOLTAGES
AVDD33, DVDD33
ppm/°C
V
kΩ
1.1ꢀ
1.3
1.1ꢀ
1.3
1.1ꢀ
1.3
ꢀ
ꢀ
ꢀ
3.13
1.70
3.47 3.13
1.90 1.70
3.47 3.13
1.90 1.70
3.47
1.90
V
V
CVDD18, DVDD18
POWER SUPPLY CURRENTS
IAVDD33
IDVDD33
ICVDD18
IDVDD18
ꢀ6
10
18
28
60
14
22
32
ꢀ6
10
18
29
60
14
22
33
ꢀ6
11
18
30
60
1ꢀ
22
34
mA
mA
mA
mA
POWER DISSIPATION
fDAC = 2ꢀ0 MSPS, fOUT = 20 MHz
DAC Outputs Disabled
Full Device Power-Down
OPERATING TEMPERATURE
300
11ꢀ
3
34ꢀ
300
11ꢀ
3
34ꢀ
30ꢀ
120
3
3ꢀ0
mW
mW
mW
−40
+8ꢀ −40
+8ꢀ −40
+8ꢀ °C
Rev. 0 | Page 3 of 28
AD9741/AD9743/AD9745/AD9746/AD9747
TMIN to TMAX, AVDD33 = 3.3 V, DVDD33 = 3.3 V, DVDD18 = 1.8 V, CVDD18 = 1.8 V, IFS = 20 mA, full-scale digital input, maximum
sample rate, unless otherwise noted. The AD9745 is repeated in Table 2 so the user can compare it with all other parts.
Table 2. AD9745, AD9746, and AD9747
AD9745
Min Typ
12
AD9746
Max Min Typ
14
AD9747
Max Min Typ
16
Parameter
Unit
Max
RESOLUTION
Bits
ACCURACY
Differential Nonlinearity (DNL)
Integral Nonlinearity (INL)
MAIN DAC OUTPUTS
Offset Error
0.13
0.2ꢀ
0.ꢀ
1.0
2.0
4.0
LSB
LSB
0.001
0.001
0.001
%FSR
Offset Error Temperature Coefficient
Gain Error
0.1
0.1
0.1
ppm/°C
%FSR
ppm/°C
%FSR
2.0
100
1.0
2.0
100
1.0
2.0
100
1.0
Gain Error Temperature Coefficient
Gain Matching (DAC1 to DAC2)
Full-Scale Output Current
Output Compliance Voltage
Output Resistance
8.6
−1.0
31.7 8.6
+1.0 −1.0
31.7 8.6
+1.0 −1.0
31.7 mA
+1.0
V
MΩ
10
10
10
10
10
10
AUXILIARY DAC OUTPUTS
Resolution
Bits
Full-Scale Output Current
Output Compliance Voltage Range—Sink Current
Output Compliance Voltage Range—Source Current
Output Resistance
−2.0
0.8
0
+2.0 −2.0
+2.0 −2.0
+2.0 mA
1.6
1.6
0.8
0
1.6
1.6
0.8
0
1.6
1.6
V
V
1
1
1
MΩ
Bits
Monotonicity
10
10
10
REFERENCE INPUT/OUTPUT
Output Voltage
1.2
10
1.2
10
1.2
10
V
Output Voltage Temperature Coefficient
External Input Voltage Range
Input or Output Resistance
POWER SUPPLY VOLTAGES
AVDD33, DVDD33
ppm/°C
V
kΩ
1.1ꢀ
1.3
1.1ꢀ
1.3
1.1ꢀ
1.3
ꢀ
ꢀ
ꢀ
3.13
1.70
3.47 3.13
1.90 1.70
3.47 3.13
1.90 1.70
3.47
1.90
V
V
CVDD18, DVDD18
POWER SUPPLY CURRENTS
IAVDD33
IDVDD33
ICVDD18
IDVDD18
ꢀ6
11
18
30
60
1ꢀ
22
34
ꢀ6
12
18
31
60
16
22
3ꢀ
ꢀ6
12
18
32
60
16
22
36
mA
mA
mA
mA
POWER DISSIPATION
fDAC = 2ꢀ0 MSPS, fOUT = 20 MHz
DAC Outputs Disabled
Full Device Power-Down
OPERATING TEMPERATURE
30ꢀ
120
3
3ꢀ0
310
12ꢀ
3
3ꢀꢀ
310
12ꢀ
3
3ꢀꢀ
+8ꢀ
mW
mW
mW
°C
−40
+8ꢀ
−40
+8ꢀ
−40
Rev. 0 | Page 4 of 28
AD9741/AD9743/AD9745/AD9746/AD9747
AC SPECIFICATIONS
TMIN to TMAX, AVDD33 = 3.3 V, DVDD33 = 3.3 V, DVDD18 = 1.8 V, CVDD18 = 1.8 V, IFS = 20 mA, full-scale digital input, maximum
sample rate, unless otherwise noted.
Table 3. AD9741, AD9743, and AD9745
AD9741
Min Typ
AD9743
Max Min Typ
AD9745
Max Min Typ
Parameter
Unit
Max
SPURIOUS FREE DYNAMIC RANGE (SFDR)
fDAC = 2ꢀ0 MSPS, fOUT = 20 MHz
fDAC = 2ꢀ0 MSPS, fOUT = 70 MHz
fDAC = 2ꢀ0 MSPS, fOUT = 180 MHz1
INTERMODULATION DISTORTION (IMD)
fDAC = 2ꢀ0 MSPS, fOUT = 20 MHz
fDAC = 2ꢀ0 MSPS, fOUT = 70 MHz
fDAC = 2ꢀ0 MSPS, fOUT = 180 MHz1
CROSSTALK
70
70
64
80
70
64
82
70
66
dBc
dBc
dBc
80
80
72
80
80
72
86
80
74
dBc
dBc
dBc
fDAC = 2ꢀ0 MSPS, fOUT = 20 MHz
fDAC = 2ꢀ0 MSPS, fOUT = 70 MHz
fDAC = 2ꢀ0 MSPS, fOUT = 180 MHz1
80
80
80
80
80
80
80
80
80
dBc
dBc
dBc
ADJACENT CHANNEL LEAKAGE RATIO (ACLR) SINGLE
CARRIER WCDMA
fDAC = 24ꢀ.76 MSPS, fOUT = 1ꢀ.36 MHz
fDAC = 24ꢀ.76 MSPS, fOUT = 61.44 MHz
fDAC = 24ꢀ.76 MSPS, fOUT = 184.32 MHz1
NOISE SPECTRAL DENSITY (NSD)
ꢀ4
ꢀ4
ꢀ4
66
66
64
76
76
72
dBc
dBc
dBc
fDAC = 24ꢀ.76 MSPS, fOUT = 1ꢀ.36 MHz
fDAC = 24ꢀ.76 MSPS, fOUT = 61.44 MHz
fDAC = 24ꢀ.76 MSPS, fOUT = 184.32 MHz1
−132
−132
−13ꢀ
−144
−144
−147
−1ꢀꢀ
−1ꢀꢀ
−1ꢀꢀ
dBm/Hz
dBm/Hz
dBm/Hz
1 Mix Mode.
Rev. 0 | Page ꢀ of 28
AD9741/AD9743/AD9745/AD9746/AD9747
TMIN to TMAX, AVDD33 = 3.3 V, DVDD33 = 3.3 V, DVDD18 = 1.8 V, CVDD18 = 1.8 V, IFS = 20 mA, full-scale digital input, maximum
sample rate, unless otherwise noted. The AD9745 is repeated in Table 4 so the user can compare it with all other parts.
Table 4. AD9745, AD9746, and AD9747
AD9745
Min Typ
AD9746
Max Min Typ
AD9747
Max Min Typ
Parameter
Unit
Max
SPURIOUS FREE DYNAMIC RANGE (SFDR)
fDAC = 250 MSPS, fOUT = 20 MHz
fDAC = 250 MSPS, fOUT = 70 MHz
fDAC = 250 MSPS, fOUT = 180 MHz1
INTERMODULATION DISTORTION (IMD)
fDAC = 250 MSPS, fOUT = 20 MHz
fDAC = 250 MSPS, fOUT = 70 MHz
fDAC = 250 MSPS, fOUT = 180 MHz1
CROSSTALK
82
70
66
82
70
66
82
70
66
dBc
dBc
dBc
86
80
74
86
80
74
86
80
74
dBc
dBc
dBc
fDAC = 250 MSPS, fOUT = 20 MHz
fDAC = 250 MSPS, fOUT = 70 MHz
fDAC = 250 MSPS, fOUT = 180 MHz1
80
80
80
80
80
80
80
80
80
dBc
dBc
dBc
ADJACENT CHANNEL LEAKAGE RATIO (ACLR) SINGLE
CARRIER WCDMA
fDAC = 245.76 MSPS, fOUT = 15.36 MHz
fDAC = 245.76 MSPS, fOUT = 61.44 MHz
fDAC = 245.76 MSPS, fOUT = 184.32 MHz1
NOISE SPECTRAL DENSITY (NSD)
76
76
72
78
78
74
82
80
74
dBc
dBc
dBc
fDAC = 245.76 MSPS, fOUT = 15.36 MHz
fDAC = 245.76 MSPS, fOUT = 61.44 MHz
fDAC = 245.76 MSPS, fOUT = 184.32 MHz1
−155
−155
−155
−163
−160
−158
−165
−162
−160
dBm/Hz
dBm/Hz
dBm/Hz
1 Mix Mode.
Rev. 0 | Page 6 of 28
AD9741/AD9743/AD9745/AD9746/AD9747
DIGITAL AND TIMING SPECIFICATIONS
TMIN to TMAX, AVDD33 = 3.3 V, DVDD33 = 3.3 V, DVDD18 = 1.8 V, CVDD18 = 1.8 V, IFS = 20 mA, full-scale digital input, maximum
sample rate, unless otherwise noted.
Table 5. AD9741/AD9743/AD9745/AD9746/AD9747
Parameter
Min
400
300
Typ
800
400
Max
Unit
DAC CLOCK INPUTS (CLKP, CLKN)
Differential Peak-to-Peak Voltage
Single-Ended Peak-to-Peak Voltage
Common-Mode Voltage
Input Current
1600
800
ꢀ00
1
mV
mV
mV
μA
Input Frequency
2ꢀ0
MHz
DATA CLOCK OUTPUT (DCO)
Output Voltage High
Output Voltage Low
Output Current
DAC Clock to Data Clock Output Delay (tDCO
2.4
V
V
mA
ns
0.4
10
2.8
)
2.0
2.0
2.2
DATA PORT INPUTS
Input Voltage High
V
Input Voltage Low
Input Current
Data to DAC Clock Setup Time (tDBS Dual-Port Mode)
Data to DAC Clock Hold Time (tDBH Dual-Port Mode)
0.8
1
V
μA
ps
400
1200
ps
DAC Clock to Analog Output Data Latency (Dual-Port Mode)
Data or IQSEL Input to DAC Clock Setup Time (tDBS Single-Port Mode)
Data or IQSEL Input to DAC Clock Hold Time (tDBH Single-Port Mode)
DAC Clock to Analog Output Data Latency (Single-Port Mode)
SERIAL PERIPHERAL INTERFACE
7
Cycles
ps
ps
400
1200
8
Cycles
SCLK Frequency (fSCLK
SCLK Pulse Width High (tPWH
SCLK Pulse Width Low (tPWL
CSB to SCLK Setup Time (tS)
CSB to SCLK Hold Time (tH)
)
40
MHz
ns
ns
ns
ns
)
10
10
1
)
0
SDIO to SCLK Setup Time (tDS)
1
ns
SDIO to SCLK Hold Time (tDH)
0
ns
SCLK to SDIO/SDO Data Valid Time (tDV)
RESET Pulse Width High
1
ns
ns
10
WAKE-UP TIME AND OUTPUT LATENCY
From DAC Outputs Disabled
From Full Device Power-Down
DAC Clock to Analog Output Latency (Dual-Port Mode)
DAC Clock to Analog Output Latency (Single-Port Mode)
200
1200
7
μs
μs
Cycles
Cycles
8
Rev. 0 | Page 7 of 28
AD9741/AD9743/AD9745/AD9746/AD9747
ABSOLUTE MAXIMUM RATINGS
THERMAL RESISTANCE
Table 6.
Thermal resistance tested using JEDEC standard 4-layer
thermal test board with no airflow.
With
Respect to
Parameter
Rating
AVDD33, DVDD33
AVSS DVSS
CVSS
−0.3 V to +3.6 V
Table 7.
DVDD18, CVDD18
AVSS DVSS
CVSS
−0.3 V to +1.98 V
Package Type
θJA
Unit
CP-72-1 (Exposed Pad Soldered to PCB)
2ꢀ
°C/W
AVSS
DVSS
CVSS
REFIO
DVSS CVSS
AVSS CVSS
AVSS DVSS
AVSS
−0.3 V to +0.3 V
−0.3 V to +0.3 V
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
−0.3 V to +0.3 V
−0.3 V to AVDD33 + 0.3 V
−1.0 V to AVDD33 + 0.3 V
IOUT1P, IOUT1N, IOUT2P,
IOUT2P, AUX1P, AUX1N,
AUX2P, AUX2N
AVSS
P1D1ꢀ to P1D0,
P2D1ꢀ to P2D0
DVSS
−0.3 V to DVDD33 + 0.3 V
CLKP, CLKN
CVSS
DVSS
−0.3 V to CVDD18 + 0.3 V
–0.3 V to DVDD33 + 0.3 V
12ꢀ°C
RESET, CSB, SCLK, SDIO, SDO
Junction Temperature
Storage Temperature
ESD CAUTION
−6ꢀ°C to +1ꢀ0°C
Rev. 0 | Page 8 of 28
AD9741/AD9743/AD9745/AD9746/AD9747
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
CVDD18
CVSS
CLKP
CLKN
CVSS
CVDD18
DVSS
DVDD18
P1D7
1
2
3
4
5
6
7
8
9
54 FSADJ
53 RESET
52 CSB
51 SCLK
50 SDIO
49 SDO
48 DVSS
47 DVDD18
46 NC
PIN 1
INDICATOR
AD9741
(TOP VIEW)
P1D6 10
P1D5 11
P1D4 12
P1D3 13
P1D2 14
P1D1 15
P1D0 16
NC 17
45 NC
44 NC
43 NC
42 NC
41 NC
40 NC
39 NC
38 P2D0
37 P2D1
NC 18
NC = NO CONNECT
Figure 2. AD9741 Pin Configuration
Table 8. AD 9741 Pin Function Descriptions
Pin No.
Mnemonic
Description
1, 6
2, ꢀ
3
CVDD18
CVSS
CLKP
Clock Supply Voltage (1.8 V).
Clock Supply Common (0 V).
Differential DAC Clock Input.
4
CLKN
DVSS
Complementary Differential DAC Clock Input.
Digital Supply Common (0 V).
7, 28, 48
8, 47
9 to 16
17 to 24, 26, 30, 39 to 46
DVDD18
P1D<7:0>
NC
Digital Core Supply Voltage (1.8 V).
Port 1 Data Bit Inputs.
No Connect.
2ꢀ
27
29
31 to 38
DCO
DVDD33
IQSEL
P2D<7:0>
SDO
Data Clock Output. Use to clock data source.
Digital I/O Supply Voltage (3.3 V).
I/Q Framing Signal for Single-Port Mode Operation.
Port 2 Data Bit Inputs.
49
Serial Peripheral Interface Data Output.
ꢀ0
ꢀ1
SDIO
SCLK
Serial Peripheral Interface Data Input and Optional Data Output.
Serial Peripheral Interface Clock Input.
ꢀ2
ꢀ3
ꢀ4
ꢀꢀ
CSB
Serial Peripheral Interface Chip Select Input. Active low.
Hardware Reset. Active high.
Full-Scale Current Output Adjust. Connect a 10 kΩ resistor to AVSS.
Reference Input/Output. Connect a 0.1 μF capacitor to AVSS.
Analog Supply Voltage (3.3 V).
RESET
FSADJ
REFIO
AVDD33
AVSS
ꢀ6, ꢀ7, 71, 72
ꢀ8, 61, 64, 67, 70
Analog Supply Common (0 V).
ꢀ9
60
62
63
6ꢀ
66
68
69
IOUT2P
IOUT2N
AUX2P
AUX2N
AUX1N
AUX1P
IOUT1N
IOUT1P
AVSS
DAC2 Current Output True. Sources full-scale current when input data bits are all 1.
DAC2 Current Output Complement. Sources full-scale current when data bits are all 0.
Auxiliary DAC2 Default Current Output Pin.
Auxiliary DAC2 Optional Output Pin. Enable through SPI.
Auxiliary DAC1 Optional Output Pin. Enable through SPI.
Auxiliary DAC1 Default Current Output Pin.
Complementary DAC1 Current Output. Sources full-scale current when data bits are all 0.
DAC1 Current Output. Sources full-scale current when data bits are all 1.
Exposed Thermal Pad. Must be soldered to copper pour on top surface of PCB for mechanical
stability and must be electrically tied to low impedance GND plane for low noise performance.
EPAD
Rev. 0 | Page 9 of 28
AD9741/AD9743/AD9745/AD9746/AD9747
CVDD18
CVSS
CLKP
CLKN
CVSS
CVDD18
DVSS
DVDD18
P1D9
1
2
3
4
5
6
7
8
9
54 FSADJ
53 RESET
52 CSB
51 SCLK
50 SDIO
49 SDO
48 DVSS
47 DVDD18
46 NC
PIN 1
INDICATOR
AD9743
(TOP VIEW)
P1D8 10
P1D7 11
P1D6 12
P1D5 13
P1D4 14
P1D3 15
P1D2 16
P1D1 17
P1D0 18
45 NC
44 NC
43 NC
42 NC
41 NC
40 P2D0
39 P2D1
38 P2D2
37 P2D3
NC = NO CONNECT
Figure 3. AD9743 Pin Configuration
Table 9. AD 9743 Pin Function Descriptions
Pin No.
Mnemonic
Description
1, 6
2, ꢀ
3
4
CVDD18
CVSS
CLKP
CLKN
DVSS
DVDD18
P1D<9:0>
NC
Clock Supply Voltage (1.8 V).
Clock Supply Common (0 V).
Differential DAC Clock Input.
Complementary Differential DAC Clock Input.
Digital Supply Common (0 V).
Digital Core Supply Voltage (1.8 V).
Port 1 Data Bit Inputs.
7, 28, 48
8, 47
9 to 18
19 to 24, 26, 30, 41 to 46
No Connect.
2ꢀ
27
29
31 to 40
DCO
DVDD33
IQSEL
P2D<9:0>
SDO
Data Clock Output. Use to clock data source.
Digital I/O Supply Voltage (3.3 V).
I/Q Framing Signal for Single-Port Mode Operation.
Port 2 Data Bit Inputs.
49
Serial Peripheral Interface Data Output.
ꢀ0
ꢀ1
SDIO
SCLK
Serial Peripheral Interface Data Input and Optional Data Output.
Serial Peripheral Interface Clock Input.
ꢀ2
ꢀ3
ꢀ4
ꢀꢀ
CSB
Serial Peripheral Interface Chip Select Input. Active low.
Hardware Reset. Active high.
Full-Scale Current Output Adjust. Connect a 10 kΩ resistor to AVSS.
Reference Input/Output. Connect a 0.1 μF capacitor to AVSS.
Analog Supply Voltage (3.3 V).
RESET
FSADJ
REFIO
AVDD33
AVSS
ꢀ6, ꢀ7, 71, 72
ꢀ8, 61, 64, 67, 70
Analog Supply Common (0 V).
ꢀ9
60
62
63
6ꢀ
66
68
69
IOUT2P
IOUT2N
AUX2P
AUX2N
AUX1N
AUX1P
IOUT1N
IOUT1P
AVSS
DAC2 Current Output True. Sources full-scale current when input data bits are all 1.
DAC2 Current Output Complement. Sources full-scale current when data bits are all 0.
Auxiliary DAC2 Default Current Output Pin.
Auxiliary DAC2 Optional Output Pin. Enable through SPI.
Auxiliary DAC1 Optional Output Pin. Enable through SPI.
Auxiliary DAC1 Default Current Output Pin.
Complementary DAC1 Current Output. Sources full-scale current when data bits are all 0.
DAC1 Current Output. Sources full-scale current when data bits are all 1.
Exposed Thermal Pad. Must be soldered to copper pour on top surface of PCB for mechanical
stability and must be electrically tied to low impedance GND plane for low noise performance.
EPAD
Rev. 0 | Page 10 of 28
AD9741/AD9743/AD9745/AD9746/AD9747
CVDD18
CVSS
CLKP
CLKN
CVSS
CVDD18
DVSS
DVDD18
P1D11
1
2
3
4
5
6
7
8
9
54 FSADJ
53 RESET
52 CSB
51 SCLK
50 SDIO
49 SDO
48 DVSS
47 DVDD18
46 NC
PIN 1
INDICATOR
AD9745
(TOP VIEW)
P1D10 10
P1D9 11
P1D8 12
P1D7 13
P1D6 14
P1D5 15
P1D4 16
P1D3 17
P1D2 18
45 NC
44 NC
43 NC
42 P2D0
41 P2D1
40 P2D2
39 P2D3
38 P2D4
37 P2D5
NC = NO CONNECT
Figure 4. AD9745 Pin Configuration
Table 10. AD9745 Pin Function Descriptions
Pin No.
Mnemonic
CVDD18
CVSS
CLKP
CLKN
DVSS
DVDD18
P1D<11:0>
Description
1, 6
2, ꢀ
3
4
7, 28, 48
8, 47
9 to 20
Clock Supply Voltage (1.8 V).
Clock Supply Common (0 V).
Differential DAC Clock Input.
Complementary Differential DAC Clock Input.
Digital Supply Common (0 V).
Digital Core Supply Voltage (1.8 V).
Port 1 Data Bit Inputs.
21 to 24, 26, 30, 43 to 46 NC
No Connect.
2ꢀ
27
29
31 to 42
DCO
DVDD33
IQSEL
P2D<11:0>
SDO
Data Clock Output. Use to clock data source.
Digital I/O Supply Voltage (3.3 V).
I/Q Framing Signal for Single-Port Mode Operation.
Port 2 Data Bit Inputs.
49
Serial Peripheral Interface Data Output.
ꢀ0
ꢀ1
SDIO
SCLK
Serial Peripheral Interface Data Input and Optional Data Output.
Serial Peripheral Interface Clock Input.
ꢀ2
ꢀ3
ꢀ4
ꢀꢀ
CSB
Serial Peripheral Interface Chip Select Input. Active low.
Hardware Reset. Active high.
Full-Scale Current Output Adjust. Connect 10 kΩ resistor to AVSS.
Reference Input/Output. Connect a 0.1 μF capacitor to AVSS.
Analog Supply Voltage (3.3 V).
RESET
FSADJ
REFIO
AVDD33
AVSS
ꢀ6, ꢀ7, 71, 72
ꢀ8, 61, 64, 67, 70
Analog Supply Common (0 V).
ꢀ9
60
62
63
6ꢀ
66
68
69
IOUT2P
IOUT2N
AUX2P
AUX2N
AUX1N
AUX1P
IOUT1N
IOUT1P
AVSS
DAC2 Current Output True. Sources full-scale current when input data bits are all 1.
DAC2 Current Output Complement. Sources full-scale current when data bits are all 0.
Auxiliary DAC2 Default Current Output Pin.
Auxiliary DAC2 Optional Output Pin. Enable through SPI.
Auxiliary DAC1 Optional Output Pin. Enable through SPI.
Auxiliary DAC1 Default Current Output Pin.
Complementary DAC1 Current Output. Sources full-scale current when data bits are all 0.
DAC1 Current Output. Sources full-scale current when data bits are all 1.
Exposed Thermal Pad. Must be soldered to copper pour on top surface of PCB for mechanical
stability and must be electrically tied to low impedance GND plane for low noise performance.
EPAD
Rev. 0 | Page 11 of 28
AD9741/AD9743/AD9745/AD9746/AD9747
CVDD18
CVSS
CLKP
CLKN
CVSS
CVDD18
DVSS
DVDD18
P1D13
1
2
3
4
5
6
7
8
9
54 FSADJ
53 RESET
52 CSB
51 SCLK
50 SDIO
49 SDO
48 DVSS
47 DVDD18
46 NC
PIN 1
INDICATOR
AD9746
(TOP VIEW)
P1D12 10
P1D11 11
P1D10 12
P1D9 13
P1D8 14
P1D7 15
P1D6 16
P1D5 17
P1D4 18
45 NC
44 P2D0
43 P2D1
42 P2D2
41 P2D3
40 P2D4
39 P2D5
38 P2D6
37 P2D7
NC = NO CONNECT
Figure 5. AD9746 Pin Configuration
Table 11. AD9746 Pin Function Descriptions
Pin No.
Mnemonic
CVDD18
CVSS
Description
1, 6
2, ꢀ
Clock Supply Voltage (1.8 V).
Clock Supply Common (0 V).
3
CLKP
Differential DAC Clock Input.
4
CLKN
DVSS
DVDD18
P1D<13:0>
Complementary Differential DAC Clock Input.
Digital Supply Common (0 V).
Digital Core Supply Voltage (1.8 V).
Port 1 Data Bit Inputs.
7, 28, 48
8, 47
9 to 22
23, 24, 26, 30, 4ꢀ, 46 NC
No Connect.
2ꢀ
27
29
31 to 44
DCO
DVDD33
IQSEL
P2D<13:0>
SDO
Data Clock Output. Use to clock data source.
Digital I/O Supply Voltage (3.3 V).
I/Q Framing Signal for Single-Port Mode Operation.
Port 2 Data Bit Inputs.
49
Serial Peripheral Interface Data Output.
ꢀ0
ꢀ1
SDIO
SCLK
Serial Peripheral Interface Data Input and Optional Data Output.
Serial Peripheral Interface Clock Input.
ꢀ2
ꢀ3
ꢀ4
ꢀꢀ
CSB
Serial Peripheral Interface Chip Select Input. Active low.
Hardware Reset. Active high.
Full-Scale Current Output Adjust. Connect a 10 kΩ resistor to AVSS.
Reference Input/Output. Connect a 0.1 μF capacitor to AVSS.
Analog Supply Voltage (3.3 V).
RESET
FSADJ
REFIO
AVDD33
AVSS
ꢀ6, ꢀ7, 71, 72
ꢀ8, 61, 64, 67, 70
Analog Supply Common (0 V).
ꢀ9
60
62
63
6ꢀ
66
68
69
IOUT2P
IOUT2N
AUX2P
AUX2N
AUX1N
AUX1P
IOUT1N
IOUT1P
AVSS
DAC2 Current Output True. Sources full-scale current when input data bits are all 1.
DAC2 Current Output Complement. Sources full-scale current when data bits are all 0.
Auxiliary DAC2 Default Current Output Pin.
Auxiliary DAC2 Optional Output Pin. Enable through SPI.
Auxiliary DAC1 Optional Output Pin. Enable through SPI.
Auxiliary DAC1 Default Current Output Pin.
Complementary DAC1 Current Output. Sources full-scale current when data bits are all 0.
DAC1 Current Output. Sources full-scale current when data bits are all 1.
Exposed Thermal Pad. Must be soldered to copper pour on top surface of PCB for mechanical stability
and must be electrically tied to low impedance GND plane for low noise performance.
EPAD
Rev. 0 | Page 12 of 28
AD9741/AD9743/AD9745/AD9746/AD9747
CVDD18
CVSS
CLKP
CLKN
CVSS
1
2
3
4
5
6
7
8
9
54 FSADJ
53 RESET
52 CSB
51 SCLK
50 SDIO
49 SDO
PIN 1
INDICATOR
CVDD18
DVSS
DVDD18
P1D15
P1D14 10
P1D13 11
P1D12 12
P1D11 13
P1D10 14
P1D9 15
P1D8 16
P1D7 17
P1D6 18
48 DVSS
AD9747
(TOP VIEW)
47 DVDD18
46 P2D0
45 P2D1
44 P2D2
43 P2D3
42 P2D4
41 P2D5
40 P2D6
39 P2D7
38 P2D8
37 P2D9
NC = NO CONNECT
Figure 6. AD9747 Pin Configuration
Table 12. AD9747 Pin Function Descriptions
Pin No.
Mnemonic
CVDD18
CVSS
CLKP
CLKN
Description
1, 6
2, ꢀ
3
4
7, 28, 48
8, 47
9 to 24
2ꢀ
Clock Supply Voltage (1.8 V).
Clock Supply Common (0 V).
Differential DAC Clock Input.
Complementary Differential DAC Clock Input.
Digital Supply Common (0 V).
Digital Core Supply Voltage (1.8 V).
Port 1 Data Bit Inputs.
DVSS
DVDD18
P1D<1ꢀ:0>
DCO
Data Clock Output. Use to clock data source.
No Connect.
26, 30
NC
27
29
31 to 46
49
DVDD33
IQSEL
P2D<1ꢀ:0>
SDO
Digital I/O Supply Voltage (3.3 V).
I/Q Framing Signal for Single-Port Mode Operation.
Port 2 Data Bit Inputs.
Serial Peripheral Interface Data Output.
ꢀ0
ꢀ1
SDIO
SCLK
Serial Peripheral Interface Data Input and Optional Data Output.
Serial Peripheral Interface Clock Input.
ꢀ2
ꢀ3
CSB
RESET
Serial Peripheral Interface Chip Select Input. Active low.
Hardware Reset. Active high.
ꢀ4
ꢀꢀ
FSADJ
REFIO
AVDD33
AVSS
Full-Scale Current Output Adjust. Connect a 10 kΩ resistor to AVSS.
Reference Input/Output. Connect a 0.1 μF capacitor to AVSS.
Analog Supply Voltage (3.3 V).
ꢀ6, ꢀ7, 71, 72
ꢀ8, 61, 64, 67, 70
Analog Supply Common (0 V).
ꢀ9
60
62
63
6ꢀ
66
68
69
IOUT2P
IOUT2N
AUX2P
AUX2N
AUX1N
AUX1P
IOUT1N
IOUT1P
AVSS
DAC2 Current Output. Sources full-scale current when input data bits are all 1.
Complementary DAC2 Current Output. Sources full-scale current when data bits are all 0.
Auxiliary DAC2 Default Current Output Pin.
Auxiliary DAC2 Optional Output Pin. Enable through SPI.
Auxiliary DAC1 Optional Output Pin. Enable through SPI.
Auxiliary DAC1 Default Current Output Pin.
Complementary DAC1 Current Output. Sources full-scale current when data bits are all 0.
DAC1 Current Output. Sources full-scale current when data bits are all 1.
Exposed Thermal Pad. Must be soldered to copper pour on top surface of PCB for mechanical
stability and must be electrically tied to low impedance GND plane for low noise performance.
EPAD
Rev. 0 | Page 13 of 28
AD9741/AD9743/AD9745/AD9746/AD9747
TYPICAL PERFORMANCE CHARACTERISTICS
100
100
90
80
70
60
50
40
90
250MSPS
125MSPS
80
125MSPS
250MSPS
70
60
50
40
0
20
40
60
80
100
120
250
250
0
20
40
60
80
100
120
250
250
fOUT (MHz)
fOUT (MHz)
Figure 7. AD9747 SFDR vs. fOUT, Normal Mode
Figure 10. AD9747 IMD vs. fOUT, Normal Mode
100
90
80
70
60
50
40
100
90
80
70
60
50
40
125
150
175
200
225
125
150
175
200
225
fOUT (MHz)
fOUT (MHz)
Figure 8. AD9747 SFDR vs. fOUT, Mix Mode, 250 MSPS
Figure 11. AD9747 IMD vs. fOUT, Mix Mode, 250 MSPS
90
85
80
75
70
65
60
–152
–154
–156
–158
–160
–162
–164
–166
–168
NORMAL MODE
MIX MODE
MIX MODE
NORMAL MODE
0
50
100
150
200
0
50
100
150
200
fOUT (MHz)
fOUT (MHz)
Figure 9. AD9747 ACLR vs. fOUT, Single Carrier WCDMA, 245.76 MSPS
Figure 12. AD9747 NSD vs. fOUT, Single Carrier WCDMA, 245.76 MSPS
Rev. 0 | Page 14 of 28
AD9741/AD9743/AD9745/AD9746/AD9747
100
90
80
70
60
50
40
100
90
10mAFS
20mAFS
80
20mAFS
30mAFS
70
10mAFS
30mAFS
60
50
40
0
20
40
60
fOUT (MHz)
80
100
120
0
20
40
60
80
100
120
fOUT (MHz)
Figure 13. AD9747 SFDR vs. Analog Output, 250 MSPS
Figure 16. AD9747 IMD vs. Analog Output, 250 MSPS
100
90
80
70
60
50
40
100
90
80
70
60
50
40
0dBFS
0dBFS
–3dBFS
–6dBFS
–3dBFS
–6dBFS
0
20
40
60
80
100
120
0
20
40
60
80
100
120
fIN (MHz)
fIN (MHz)
Figure 14. AD9747 SFDR vs. Digital Input, 250 MSPS
Figure 17. AD9747 IMD vs. Digital Input, 250 MSPS
90
85
80
75
70
65
60
90
85
80
75
70
65
60
RANGE OF POSSIBLE SFDR
PERFORMANCE IS DEPENDENT ON
INPUT DATA TIMING RELATIVE TO
THE DAC CLOCK. SEE INPUT DATA
TIMING SECTION.
RANGE OF IMD PERFORMANCE IS
ESSENTIALLY INDEPENDENT OF
INPUT DATA TIMING RELATIVE TO
THE DAC CLOCK. SEE INPUT DATA
TIMING SECTION.
10
20
30
40
50
60
70
80
90 100 110
10
20
30
40
50
60
70
80
90 100 110
fOUT (MHz)
fOUT (MHz)
Figure 15. AD9747 SFDR vs. fOUT Over Input Data Timing
Figure 18. AD9747 IMD vs. fOUT Over Input Data Timing
Rev. 0 | Page 1ꢀ of 28
AD9741/AD9743/AD9745/AD9746/AD9747
1
–130
–135
–140
–145
–150
–155
–160
–165
0
–1
NORMAL MODE
–2
MIX MODE
–3
–4
–5
0
25
50
75
100 125 150 175 200 225 250
fOUT (MHz)
AD9741
AD9743
AD9745
AD9746
AD9747
Figure 19. Nominal Power in the Fundamental, IFS = 20 mA
Figure 21. NSD vs. Bit Resolution, Single Carrier WCDMA, 245.76 MSPS, fCARRIER
fCARRIER = 61.44 MHz
85
80
75
70
65
60
55
50
AD9741
AD9743
AD9745
AD9746
AD9747
Figure 20. ACLR vs. Bit Resolution, Single Carrier WCDMA, 245.76 MSPS,
fCARRIER = 61.44 MHz
Rev. 0 | Page 16 of 28
AD9741/AD9743/AD9745/AD9746/AD9747
TERMINOLOGY
Temperature Drift
Integral Nonlinearity (INL)
Temperature drift is specified as the maximum change in a
parameter from ambient temperature (25°C) to either TMIN
or TMAX and is typically reported as ppm/°C.
The maximum deviation of the actual analog output from the
ideal output, as determined by a straight line drawn from zero
scale to full scale.
Spurious-Free Dynamic Range (SFDR)
Differential Nonlinearity (DNL)
The difference in decibels between the peak amplitude of a test
tone and the peak amplitude of the largest spurious signal over
the specified bandwidth.
A measure of the maximum deviation in analog output associated
with any single value change in the digital input code relative to
an ideal LSB.
Intermodulation Distortion (IMD)
Monotonicity
The difference in decibels between the maximum peak ampli-
tude of two test tones and the maximum peak amplitude of
the distortion products created from the sum or difference of
integer multiples of the test tones.
A DAC is monotonic if the analog output increases or remains
constant in response to an increase in the digital input.
Offset Error
The deviation of the output current from the ideal zero-scale
current. For differential outputs, 0 mA is expected at IOUTP when
all inputs are low, and 0 mA is expected at IOUTN when all inputs
are high.
Adjacent Channel Leakage Ratio (ACLR)
The ratio between the measured power of a wideband signal
within a channel relative to the measured power in an empty
adjacent channel.
Gain Error
Noise Spectral Density (NSD)
The measured noise power over a 1 Hz bandwidth seen at the
analog output.
The deviation of the output current from the ideal full-scale
current. Actual full-scale output current is determined by
subtracting the output (when all inputs are low) from the
output (when all inputs are high).
Output Compliance Range
The range of allowable voltage seen by the analog output of a
current output DAC. Operation beyond the compliance limits
may cause output stage saturation and/or a breakdown resulting
in nonlinear performance.
Rev. 0 | Page 17 of 28
AD9741/AD9743/AD9745/AD9746/AD9747
THEORY OF OPERATION
transfer, and a reference register address for the first byte of the
data transfer. A logic high on the CSB pin followed by a logic
low resets the SPI port to its initial state and defines the start
of the instruction cycle. From this point, the next eight rising
SCLK edges define the eight bits of the instruction byte for the
current communication cycle.
The AD9741/AD9743/AD9745/AD9746/AD9747 combine
many features to make them very attractive for wired and
wireless communications systems. The dual DAC architecture
facilitates easy interfacing to common quadrature modulators
when designing single sideband transmitters. In addition, the
speed and performance of the devices allow wider bandwidths
and more carriers to be synthesized than in previously available
products.
The remaining SCLK edges are for Phase 2 of the communication
cycle, which is the data transfer between the serial port control-
ler and the system controller. Phase 2 can be a transfer of 1, 2, 3,
or 4 data bytes as determined by the instruction byte. Using
multibyte transfers is usually preferred although single-byte
data transfers are useful to reduce CPU overhead or when only
a single register access is required.
All features and options are software programmable through
the SPI port.
SERIAL PERIPHERAL INTERFACE
SDO
AD9747
All serial port data is transferred to and from the device in syn-
chronization with the SCLK pin. Input data is always latched
on the rising edge of SCLK whereas output data is always valid
after the falling edge of SCLK. Register contents change imme-
diately upon writing to the last bit of each transfer byte.
SDIO
SPI
SCLK
CSB
PORT
Figure 22. SPI Port
The SPI port is a flexible, synchronous serial communications
port allowing easy interfacing to many industry-standard
microcontrollers and microprocessors. The port is compatible
with most synchronous transfer formats including both the
Motorola SPI and Intel® SSR protocols.
When synchronization is lost, the device has the ability to
asynchronously terminate an I/O operation whenever the CSB
pin is taken to logic high. Any unwritten register content data is
lost if the I/O operation is aborted. Taking CSB low then resets the
serial port controller and restarts the communication cycle.
INSTRUCTION BYTE
The interface allows read and write access to all registers that
configure the AD9741/AD9743/AD9745/AD9746/AD9747.
Single or multiple byte transfers are supported as well as MSB-
first or LSB-first transfer formats. Serial data input/output can
be accomplished through a single bidirectional pin (SDIO) or
through two unidirectional pins (SDIO/SDO).
The instruction byte contains the information shown in the
following bit map.
MSB
B7
LSB
B0
B6
B5
B4
B3
B2
B1
R/W
N1
N0
A4
A3
A2
A1
A0
The serial port configuration is controlled by Register 0x00,
Bits<7:6>. It is important to note that any change made to the
serial port configuration occurs immediately upon writing to
the last bit of this byte. Therefore, it is possible with a multibyte
transfer to write to this register and change the configuration in
the middle of a communication cycle. Care must be taken to
compensate for the new configuration within the remaining
bytes of the current communication cycle.
Bit 7, R/W, determines whether a read or a write data transfer
occurs after the instruction byte write. Logic high indicates a
read operation. Logic 0 indicates a write operation.
Bits<6:5>, N1 and N0, determine the number of bytes to be
transferred during the data transfer cycle. The bits decode as
shown in Table 13.
Table 13. Byte Transfer Count
Use of a single-byte transfer when changing the serial port
configuration is recommended to prevent unexpected device
behavior.
N1
N0
Description
0
0
1
1
0
1
0
1
Transfer one byte
Transfer two bytes
Transfer three bytes
Transfer four bytes
GENERAL OPERATION OF THE SERIAL INTERFACE
There are two phases to any communication cycle with the
AD9741/AD9743/AD9745/AD9746/AD9747: Phase 1 and
Phase 2. Phase 1 is the instruction cycle, which writes an
instruction byte into the device. This byte provides the serial
port controller with information regarding Phase 2 of the
communication cycle: the data transfer cycle.
Bits<4:0>, A4, A3, A2, A1, and A0, determine which register is
accessed during the data transfer of the communications cycle.
For multibyte transfers, this address is a starting or ending
address depending on the current data transfer mode. For MSB-
first format, the specified address is an ending address or the
most significant address in the current cycle. Remaining
register addresses for multiple byte data transfers are generated
The Phase 1 instruction byte defines whether the upcoming
data transfer is read or write, the number of bytes in the data
Rev. 0 | Page 18 of 28
AD9741/AD9743/AD9745/AD9746/AD9747
internally by the serial port controller by decrementing from
the specified address. For LSB-first format, the specified address
is a beginning address or the least significant address in the
current cycle. Remaining register addresses for multiple byte
data transfers are generated internally by the serial port
controller by incrementing from the specified address.
The configuration of this pin is controlled by Register 0x00,
Bit 7. The default is Logic 0, which configures the SDIO pin
as unidirectional.
Serial Data Out (SDO)
Data is read from this pin for protocols that use separate lines
for transmitting and receiving data. The configuration of this
pin is controlled by Register 0x00, Bit 7. If this bit is set to a
Logic 1, the SDO pin does not output data and is set to a high
impedance state.
MSB/LSB TRANSFERS
The serial port can support both MSB-first and LSB-first data
formats. This functionality is controlled by Register 0x00, Bit 6.
The default is Logic 0, which is MSB-first format.
When using MSB-first format (LSBFIRST = 0), the instruction
and data bit must be written from MSB to LSB. Multibyte data
transfers in MSB-first format start with an instruction byte that
includes the register address of the most significant data byte.
Subsequent data bytes are loaded into sequentially lower
address locations. In MSB-first mode, the serial port internal
address generator decrements for each byte of the multibyte
data transfer.
INSTRUCTION CYCLE
DATA TRANSFER CYCLE
CSB
SCLK
SDIO
SDO
R/W N1 N0 A4 A3 A2 A1 A0 D7 D6 D5
D3 D2 D1 D0
0 0 0
N
N
0
0
D7 D6 D5
D3 D2 D1 D0
0 0 0
N
N
Figure 23. Serial Register Interface—MSB First
When using LSB-first format (LSBFIRST = 1), the instruction
and data bit must be written from LSB to MSB. Multibyte data
transfers in LSB-first format start with an instruction byte that
includes the register address of the least significant data byte.
Subsequent data bytes are loaded into sequentially higher
address locations. In LSB-first mode, the serial port internal
address generator increments for each byte of the multibyte
data transfer.
INSTRUCTION CYCLE
DATA TRANSFER CYCLE
CSB
SCLK
SDIO
SDO
A0 A1 A2 A3 A4 N0 N1 R/W D00 D10 D20
D4N D5N D6N D7N
D4N D5N D6N D7N
Use of a single-byte transfer when changing the serial port data
format is recommended to prevent unexpected device behavior.
D00 D10 D20
Figure 24. Serial Register Interface Timing—LSB First
SERIAL INTERFACE PORT PIN DESCRIPTIONS
Chip Select Bar (CSB)
–1
tS
fSCLK
Active low input starts and gates a communication cycle. It
allows more than one device to be used on the same serial
communication lines. CSB must stay low during the entire
communication cycle. Incomplete data transfers are aborted
anytime the CSB pin goes high. SDO and SDIO pins go to a
high impedance state when this input is high.
CSB
tPWH
tPWL
SCLK
tDS
tDH
INSTRUCTION BIT 7
INSTRUCTION BIT 6
SDIO
Serial Clock (SCLK)
Figure 25. Timing Diagram for SPI Register Write
The serial clock pin is used to synchronize data to and from the
device and to run the internal state machines. The maximum
frequency of SCLK is 40 MHz. All data input is registered on
the rising edge of SCLK. All data is driven out on the falling
edge of SCLK.
CSB
SCLK
tDV
Serial Data I/O (SDIO)
SDIO
SDO
DATA BIT N
DATA BIT N – 1
Data is always written into the device on this pin. However,
SDIO can also function as a bidirectional data output line.
Figure 26. Timing Diagram for SPI Register Read
Rev. 0 | Page 19 of 28
AD9741/AD9743/AD9745/AD9746/AD9747
SPI REGISTER MAP
Reading any register returns previously written values for all defined register bits, unless otherwise noted. Change serial port configu-
ration or execute software reset in single byte instruction only to avoid unexpected device behavior.
Table 14.
Register Name
Address Default Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
SPI Control
0x00
0x02
0x03
0x00
0x00
0x00
0x00
0xF9
0x01
0x00
0x00
0xF9
0x01
0x00
0x00
SDIODIR
DATTYPE
PD_DCO
LSBFIRST
ONEPORT
SWRESET
Data Control
Power Down
INVDCO
PD_AUX2 PD_AUX1 PD_BIAS PC_CLK PD_DAC2 PD_DAC1
DAC Mode Select 0x0A
DAC1MOD<1:0>
DAC1FSC<7:0>
DAC2MOD<1:0>
DAC1FSC<9:8>
AUXDAC1<9:8>
DAC2FSC<9:8>
AUXDAC2<9:8>
DAC1 Gain LSB
DAC1 Gain MSB
AUX DAC1 LSB
AUX DAC1 MSB
DAC2 Gain LSB
DAC2 Gain MSB
AUX DAC2 LSB
AUX DAC2 MSB
0x0B
0x0C
0x0D
0x0E
0x0F
0x10
0x11
0x12
AUXDAC1<7:0>
DAC2FSC<7:0>
AUXDAC2<7:0>
AUX1PIN
AUX2PIN
AUX1DIR
AUX2DIR
Rev. 0 | Page 20 of 28
AD9741/AD9743/AD9745/AD9746/AD9747
SPI REGISTER DESCRIPTIONS
Table 15.
Register
Address Bit Name
Description
SPI Control
0x00
7
6
ꢀ
7
6
SDIODIR
LSBFIRST
SWRESET
DATTYPE
ONEPORT
0, operate SPI in 4-wire mode, SDIO pin operates as an input only
1, operate SPI in 3-wire mode, SDIO pin operates as a bidirectional I/O line
0, LSBFIRST off, SPI serial data mode is MSB to LSB
1, LSBFIRST on, SPI serial data mode is LSB to MSB
0, resume normal operation following software RESET
1, software RESET; loads default values to all registers (except Register 0x00)
0, DAC input data is twos complement binary format
1, DAC input data is unsigned binary format
0, normal two port input mode
Data Control
Power Down
0x02
0x03
1, optional single port input mode, interleaved data received on Port 1 only
1, inverts data clock output signal
4
7
ꢀ
4
3
2
1
0
INVDCO
PD_DCO
PD_AUX2
PD_AUX1
PD_BIAS
PD_CLK
1, power down data clock output
1, power down AUX2 DAC
1, power down AUX1 DAC
1, power down reference voltage bias circuit
1, power down DAC clock input circuit
PD_DAC2
PD_DAC1
1, power down DAC2 analog output
1, power down DAC1 analog output
DAC Mode Select 0x0A
3:2 DAC1MOD<1:0> 00, selects normal mode, DAC1
01, selects mix mode, DAC1
10, selects return-to-zero mode, DAC1
1:0 DAC2MOD<1:0> 00, selects normal mode, DAC2
01, selects mix mode, DAC2
10, selects return-to-zero mode, DAC2
DAC1 Gain
AUX DAC1
0x0B
0x0C
7:0 DAC1FSC<7:0>
1:0 DAC1FSC<9:8>
DAC1 full-scale 10-bit adjustment word
0x03FF, sets full-scale current to the maximum value of 31.66 mA
0x01F9, sets full-scale current to the nominal value of 20.0 mA
0x0000, sets full-scale current to the minimum value of 8.64 mA
Auxiliary DAC1 10-bit output current adjustment word
0x03FF, sets output current magnitude to 2.0 mA
0x0200, sets output current magnitude to 1.0 mA
0x0000, sets output current magnitude to 0.0 mA
0, AUX1P output pin is active
0x0D
0x0E
7:0 AUXDAC1<7:0>
1:0 AUXDAC1<9:8>
7
6
AUX1PIN
AUX1DIR
1, AUX1N output pin is active
0, configures AUX1 DAC output to source current
1, configures AUX1 DAC output to sink current
DAC2 full-scale 10-bit adjustment word
DAC2 Gain
AUX DAC2
0x0F
0x10
7:0 DAC2FSC<7:0>
1:0 DAC2FSC<9:8>
0x03FF, sets full-scale current to the maximum value of 31.66 mA
0x01F9, sets full-scale current to the nominal value of 20.0 mA
0x0000, sets full-scale current to the minimum value of 8.64 mA
Auxiliary DAC2 10-bit output current adjustment word
0x03FF, sets output current magnitude to 2.0 mA
0x0200, sets output current to 1.0 mA
0x11
0x12
7:0 AUXDAC2<7:0>
1:0 AUXDAC2<9:8>
0x0000, sets output current to 0.0 mA
7
6
AUX2PIN
AUX2DIR
0, AUX2P output pin is active
1, AUX2N output pin is active
0, configures AUX2 DAC output to source current
1, configures AUX2 DAC output to sink current
Rev. 0 | Page 21 of 28
AD9741/AD9743/AD9745/AD9746/AD9747
DIGITAL INPUTS AND OUTPUTS
In Figure 27, data samples for DAC1 are labeled Ix and data
samples for DAC2 are labeled Qx. Note that the differential
DAC clock input is shown in a logical sense (CLKP/CLKN).
The data clock output is labeled DCO.
The AD9741/AD9743/AD9745/AD9746/AD9747 can operate
in two data input modes: dual-port mode and single-port mode.
For the default dual-port mode (ONEPORT = 0), each DAC
receives data from a dedicated input port. In single-port mode
(ONEPORT = 1), however, both DACs receive data from Port 1.
In single-port mode, DAC1 and DAC2 data is interleaved and
the IQSEL input is used to steer data to the correct DAC.
Setup and hold times are referenced to the positive transition of
the DAC clock. Data should arrive at the input pins such that
the minimum setup and hold times are met. Note that the data
clock output has a fixed time delay from the DAC clock and
may be a more convenient signal to use to confirm timing.
In single-port mode, when the IQSEL input is high, Port 1
data is delivered to DAC1 and when IQSEL is low, Port 1 data
is delivered to DAC2. The IQSEL input should always coincide
and be time-aligned with the other data bus signals. In single-
port mode, minimum setup and hold times apply to the IQSEL
input as well as to the input data signals. In dual-port mode, the
IQSEL input is ignored.
SINGLE-PORT MODE TIMING
The single-port mode timing diagram is shown in Figure 28.
CLKP/CLKN
tDCO
DCO
tDBH
I1
In dual-port mode, the data must be delivered at the sample rate
(up to 250 MSPS). In single-port mode, data must be delivered
at twice the sample rate. Because the data inputs function only
up to 250 MSPS, it is only practical to operate the DAC clock at
up to 125 MHz in single-port mode.
tDBS
P1D<15:0>
IQSEL
Q1
I2
Q2
Figure 28. Data Interface Timing, Single-Port Mode
In single-port mode, data for both DACs is received on the
In both dual-port and single-port modes, a data clock output
(DCO) signal is available as a fixed time base with which to
stimulate data from an FPGA. This output signal always
operates at the sample rate. It may be inverted by asserting
the INVDCO bit.
Port 1 input bus. Ix and Qx data samples are interleaved and
arrive twice as fast as in dual-port mode. Accompanying the
data is the IQSEL input signal, which steers incoming data to its
respective DAC. When IQSEL is high, data is steered to DAC1
and when IQSEL is low, data is steered to DAC2. IQSEL should
coincide as well as be time-aligned with incoming data.
INPUT DATA TIMING
With most DACs, signal-to-noise ratio (SNR) is a function of
the relationship between the position of the clock edges and the
point in time at which the input data changes. The AD9741/
AD9743/AD9745/AD9746/AD9747 are rising edge triggered
and thus exhibit greater SNR sensitivity when the data tran-
sition is close to this edge.
SPI PORT, RESET, AND PIN MODE
In general, when the AD9741/AD9743/AD9745/AD9746/
AD9747 are powered up, an active high pulse applied to the
RESET pin should follow. This insures the default state of all
control register bits. In addition, once the RESET pin goes low,
the SPI port can be activated, so CSB should be held high.
The specified minimum setup and hold times define a window
of time, within each data period, where the data is sampled
correctly. Generally, users should position data to arrive
relative to the DAC clock and well beyond the minimum
setup and minimum hold times. This becomes increasingly
more important at increasingly higher sample rates.
For applications without a controller, the AD9741/AD9743/
AD9745/AD9746/AD9747 also support pin mode operation,
which allows some functional options to be pin, selected with-
out the use of the SPI port. Pin mode is enabled anytime the
RESET pin is held high. In pin mode, the four SPI port pins
take on secondary functions, as shown in Table 16.
DUAL-PORT MODE TIMING
Table 16. SPI Pin Functions (Pin Mode)
The timing diagram for the dual-port mode is shown in
Figure 27.
Pin Name
Pin Mode Description
SCLK
ONEPORT (Register 0x02, Bit 6), bit value (1/0)
equals pin state (high/low)
CLKP/CLKN
tDCO
SDIO
CSB
DATTYPE (Register 0x02, Bit 7), bit value (1/0)
equals pin state (high/low)
Enable Mix Mode, if CSB is high, Register 0x0A
is set to 0x05 putting both DAC1 and DAC2 into
mix mode
DCO
tDBS tDBH
P1D<15:0>
P2D<15:0>
I1
I2
I3
I4
Q1
Q2
Q3
Q4
Figure 27. Data Interface Timing, Dual-Port Mode
SDO
Enable full power-down, if SDO is high, Register
0x03 is set to 0xFF
Rev. 0 | Page 22 of 28
AD9741/AD9743/AD9745/AD9746/AD9747
It is important to use CVDD18 and CVSS for any clock bias
circuit as noise that is coupled onto the clock from another
power supply is multiplied by the DAC input signal and
degrades performance.
In pin mode, all register bits are reset to their default values
with the exception of those that are controlled by the SPI pins.
Note also that the RESET pin should be allowed to float and
must be pulled low. Connect an external 10 kΩ resistor to
DVSS. This avoids unexpected behavior in noisy environments.
FULL-SCALE CURRENT GENERATION
The full-scale currents on DAC1 and DAC2 are functions of
the current drawn through an external resistor connected to
the FSADJ pin (Pin 54). The required value for this resistor is
10 kΩ. An internal amplifier sets the current through the
resistor to force a voltage equal to the band gap voltage of 1.2 V.
This develops a reference current in the resistor of 120 μA.
DRIVING THE DAC CLOCK INPUT
The DAC clock input requires a low jitter drive signal. It is a
PMOS differential pair powered from the CVDD18 supply.
Each pin can safely swing up to 800 mV p-p at a common-
mode voltage of about 400 mV. Though these levels are not
directly LVDS-compatible, CLKP and CLKN can be driven by
an ac-coupled, dc-offset LVDS signal, as shown in Figure 29.
0.1µF
AD9747
DAC1 GAIN
1.2V BANDGAP
DAC1
LVDS_P_IN
CLKP
REFIO
50Ω
50Ω
DAC FULL SCALE
REFERENCE CURRENT
CURRENT
SCALING
0.1µF
FSADJ
V
= 400mV
CM
DAC2
10kΩ
DAC2 GAIN
LVDS_N_IN
CLKN
0.1µF
Figure 33. Reference Circuitry
Figure 29. LVDS DAC Clock Drive Circuit
REFIO (Pin 55) should be bypassed to ground with a 0.1 μF
capacitor. The band gap voltage is present on this pin and can
be buffered for use in external circuitry. The typical output
impedance is near 5 kΩ. If desired, an external reference can
be connected to REFIO to overdrive the internal reference.
Using a CMOS or TTL clock is also acceptable for lower sample
rates. It can be routed through an LVDS translator and then
ac-coupled as described previously, or alternatively, it can be
transformer-coupled and clamped, as shown in Figure 30.
0.1µF
50Ω
TTL OR CMOS
CLK INPUT
CLKP
Internal current mirrors provide a means for adjusting the
DAC full-scale currents. The gain for DAC1 and DAC2 can be
adjusted independently by writing to the DAC1FSC<9:0> and
DAC2FSC<9:0> register bits. The default value of 0x01F9 for
the DAC gain registers gives an IFS of 20 mA, where IFS equals
CLKN
50Ω
BAV99ZXCT
HIGH SPEED
DUAL DIODE
V
= 400mV
CM
1.2 V
10,000
3
16
⎛
⎞
⎟
⎛
⎜
⎝
⎞
⎟
⎠
IFS =
× 72 +
×DAC n FSC
⎜
Figure 30. TTL or CMOS DAC Clock Drive Circuit
⎝
⎠
If a sine wave signal is available, it can be transformer-coupled
directly to the DAC clock inputs, as shown in Figure 31.
The full-scale output current range is 8.6 mA to 31.7 mA for
register values 0x000 to 0x3FF.
SINE WAVE
CLKP
35
INPUT
50Ω
30
25
20
15
10
5
CLKN
V
= 400mV
CM
Figure 31. Sine Wave DAC Clock Drive Circuit
The 400 mV common-mode bias voltage can be derived from
the CVDD18 supply through a simple divider network, as
shown in Figure 32.
V
= 400mV
CM
CVDD18
1kΩ
0
256
512
768
1024
DAC GAIN CODE
0.1µF
1nF
287Ω
Figure 34. IFS vs. DAC Gain Code
CVSS
Figure 32. DAC Clock VCM Circuit
Rev. 0 | Page 23 of 28
AD9741/AD9743/AD9745/AD9746/AD9747
systems and other applications requiring good frequency
domain performance, this is seldom problematic.
DAC TRANSFER FUNCTION
Each DAC output of the AD9741/AD9743/AD9745/AD9746/
The quad-switch architecture also supports two additional
modes of operation; mix mode and return-to-zero (RZ) mode.
The waveforms of these two modes are shown in Figure 35. In
mix mode, the output is inverted every other half clock cycle.
This effectively chops the DAC output at the sample rate. This
chopping has the effect of frequency shifting the sinc roll-off
from dc to fDAC. Additionally, there is a second subtle effect on
the output spectrum. The shifted spectrum is shaped by a second
sinc function with a first null at 2 × fDAC. The reason for this
shaping is that the data is not continuously varying at twice the
clock rate, but is simply repeated.
AD9747 drives complementary current outputs IOUTP and IOUTN
.
I
OUTP provides a near full-scale current output (IFS) when all bits
are high. For example,
DAC CODE = 2N − 1
where:
N = 8-/10-/12-/14-/16-bits (for AD9741/AD9743/AD9745/
AD9746/AD9747 respectively), and IOUTN provides no current.
The current output appearing at IOUTP and IOUTN is a function of
both the input code and IFS and can be expressed as
I
I
OUTP = (DAC DATA/2N) × IFS
OUTN = ((2N − 1) − DAC DATA)/2N × IFS
(1)
(2)
In RZ mode, the output is set to midscale on every other half
clock cycle. The output is similar to the DAC output in normal
mode except that the output pulses are half the width and half
the area. Because the output pulses have half the width, the
sinc function is scaled in frequency by 2 and has a first null at
2 × fDAC. Because the area of the pulses is half that of the pulses
in normal mode, the output power is half the normal mode
output power.
where DAC DATA = 0 to 2N − 1 (decimal representation).
The two current outputs typically drive a resistive load directly
or via a transformer. If dc coupling is required, IOUTP and IOUTN
should be connected to matching resistive loads (RLOAD) that are
tied to analog common (AVSS). The single-ended voltage
output appearing at the IOUTP and IOUTN pins is
V
V
OUTP = IOUTP × RLOAD
OUTN = IOUTN × RLOAD
(3)
(4)
D
D
D
D
D
D
D
D
D
D
10
INPUT DATA
DAC CLK
1
2
3
4
5
6
7
8
9
Note that to achieve the maximum output compliance of 1 V at
the nominal 20 mA output current, RLOAD must be set to 50 Ω.
Also note that the full-scale value of VOUTP and VOUTN should
not exceed the specified output compliance range to maintain
specified distortion and linearity performance.
4-SWITCH
DAC OUTPUT
t
t
(
fS MIX MODE)
There are two distinct advantages to operating the AD9741/
AD9743/AD9745/AD9746/AD9747 differentially. First, differ-
ential operation helps cancel common-mode error sources
associated with IOUTP and IOUTN, such as noise, distortion, and
dc offsets. Second, the differential code dependent current
and subsequent output voltage (VDIFF) is twice the value of the
single-ended voltage output (VOUTP or VOUTN), providing 2×
signal power to the load.
4-SWITCH
DAC OUTPUT
(RETURN TO
ZERO MODE)
Figure 35. Mix Mode and RZ Mode DAC Waveforms
The functions that shape the output spectrums for normal mode,
mix mode, and RZ mode, are shown in Figure 36. Switching
between the modes reshapes the sinc roll off inherent at the
DAC output. This ability to change modes in the AD9741/
AD9743/AD9745/D9746/AD9747 makes the parts suitable for
direct IF applications. The user can place a carrier anywhere in
the first three Nyquist zones depending on the operating mode
selected. The performance and maximum amplitude in all three
zones are impacted by this sinc roll off depending on where the
carrier is placed, as shown in Figure 36.
V
DIFF = (IOUTP – IOUTN) × RLOAD
(5)
ANALOG MODES OF OPERATION
The AD9741/AD9743/AD9745/AD9746/AD9747 utilize a
proprietary quad-switch architecture that lowers the distortion
of the DAC output by eliminating a code dependent glitch that
occurs with conventional dual-switch architectures. But whereas
this architecture eliminates the code dependent glitches, it creates
a constant glitch at a rate of 2 × fDAC. For communications
Rev. 0 | Page 24 of 28
AD9741/AD9743/AD9745/AD9746/AD9747
QUADRATURE
MODULATOR V+
0
–10
–20
–30
–40
MIX
RZ
AD9747
AUX
DAC1 OR
DAC2
QUAD MOD
I OR Q INPUTS
NORMAL
OPTIONAL
PASSIVE
FILTERING
AD9747
DAC1 OR
DAC2
25Ω TO 50Ω
25Ω TO 50Ω
0.5
1.5
2
Figure 38. DAC DC Coupled to Quadrature Modulator with Passive DC Shift
F
S
POWER DISSIPATION
Figure 36. Transfer Function for Each Analog Operating Mode
Figure 39 shows the power dissipation and current draw of the
AD9741/AD9743/AD9745/AD9746/AD9747. It shows that the
devices have a quiescent power dissipation of about 190 mW.
Most of this comes from the AVDD33 supply. Total power
dissipation increases about 50% as the clock rate is increased
to the maximum clock rate of 250 MHz.
AUXILIARY DACS
Two auxiliary DACs are provided on the AD9741/AD9743/
AD9745/AD9746/AD9747. A functional diagram is shown
in Figure 37. The auxiliary DACs are current output devices
with two output pins, AUXP and AUXN. The active pin can
be programmed to either source or sink current. When either
sinking or sourcing, the full-scale current magnitude is 2 mA.
The available compliance range at the auxiliary DAC outputs
depends on whether the output is configured to a sink or source
current. When sourcing current, the compliance voltage is 0 V
to 1.6 V, but when sinking current, the output compliance
voltage reduces to 0.8 V to 1.6 V. Either output can be used, but
only one output of the auxiliary DAC (P or N) is active at any
time. The inactive pin is always in a high impedance state
(>100 kΩ).
350
310
fOUT = NYQUIST
270
fOUT = DC
230
190
150
0mA
TO
2mA
AUXP
V
BIAS
0
25
50
75
100 125 150 175 200 225 250
fDAC (MHz)
AUXN
0mA
SINK
OR
SOURCE
POSITIVE
OR
NEGATIVE
TO
Figure 39. AD9747 Power Dissipation vs. fDAC
2mA
15
12
9
Figure 37. Auxiliary DAC Functional Diagram
In a single side band transmitter application, the combination of
the input referred dc offset voltage of the quadrature modulator
and the DAC output offset voltage can result in local oscillator
(LO) feedthrough at the modulator output, which degrades
system performance. The auxiliary DACs can be used to remove
the dc offset and the resulting LO feedthrough. The circuit
configuration for using the auxiliary DACs for performing
dc offset correction depends on the details of the DAC and
modulator interface. An example of a dc-coupled configuration
with low-pass filtering is outlined in the Power Dissipation
section.
AD9747
6
AD9741
3
0
0
25
50
75
100 125 150 175 200 225 250
fDAC (MHz)
Figure 40. DVDD33 Current vs. fDAC
Rev. 0 | Page 2ꢀ of 28
AD9741/AD9743/AD9745/AD9746/AD9747
30
Figure 43 shows the power consumption for each power supply
domain as well as the total power consumption. Individual bars
within each group display the power in full active mode (blue)
vs. power for five increasing levels of power-down.
350
24
AD9747
18
12
6
FULL ACTIVE
DCO OFF
AUX OFF
DAC OFF
CLK OFF
300
BIAS OFF
250
AD9741
200
150
100
50
0
0
25
50
75
100 125 150 175 200 225 250
fDAC (MHz)
Figure 41. DVDD18 Current vs. fDAC
15
13
11
9
0
AVDD33
DVDD18
CVDD18
DVDD33
TOT PWR
Figure 43. Power Dissipation vs. Power-Down Mode
The overall power consumption is dominated by AVDD33 and
significant power savings can be achieved simply by disabling
the DAC outputs. Also, disabling the DAC outputs is a signifi-
cant way to conserve power and still maintain a fast wake-up
time. Full power-down disables all circuitry for minimum
power consumption. Note, however, that even in full power-
down, there is a small power draw (25 mW) due to incoming
data activity. To lower power consumption to near zero, all
incoming data activity must be halted.
7
5
0
25
50
75
100 125 150 175 200 225 250
fDAC (MHz)
Figure 42. CVDD18 Current vs. fDAC
Rev. 0 | Page 26 of 28
AD9741/AD9743/AD9745/AD9746/AD9747
OUTLINE DIMENSIONS
0.30
0.23
0.18
0.60 MAX
10.00
BSC SQ
0.60 MAX
PIN 1
INDICATOR
55
54
72
1
PIN 1
INDICATOR
0.50
BSC
9.75
BSC SQ
4.70
BSC SQ
TOP VIEW
EXPOSED
PAD
(BOTTOM VIEW)
0.50
0.40
0.30
18
19
37
36
0.80 MAX
0.65 TYP
9.00 REF
1.00
0.85
0.80
12° MAX
EXPOSED PAD MUST BE
SOLDERED TO PCB AND
CONNECTED TO AVSS.
0.05 MAX
0.02 NOM
SEATING
PLANE
0.20 REF
COMPLIANT TO JEDEC STANDARDS MO-220-VNND-3
Figure 44. 72-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
10 mm × 10 mm, Very Thin Quad
(CP-72-1)
Dimensions shown in millimeters
ORDERING GUIDE
Model
Temperature Range
−40°C to +85°C
Package Description
72-Lead LFCSP_VQ
72-Lead LFCSP_VQ
72-Lead LFCSP_VQ
72-Lead LFCSP_VQ
72-Lead LFCSP_VQ
72-Lead LFCSP_VQ
72-Lead LFCSP_VQ
72-Lead LFCSP_VQ
72-Lead LFCSP_VQ
72-Lead LFCSP_VQ
Evaluation Board
Evaluation Board
Evaluation Board
Evaluation Board
Evaluation Board
Package Option
AD9741BCPZ1
AD9741BCPZRL1
AD9743BCPZ1
AD9743BCPZRL1
AD9745BCPZ1
AD9745BCPZRL1
AD9746BCPZ1
AD9746BCPZRL1
AD9747BCPZ1
AD9747BCPZRL1
AD9741-EBZ1
AD9743-EBZ1
AD9745-EBZ1
AD9746-EBZ1
AD9747-EBZ1
CP-72-1
CP-72-1
CP-72-1
CP-72-1
CP-72-1
CP-72-1
CP-72-1
CP-72-1
CP-72-1
CP-72-1
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
1 Z = RoHS Compliant Part.
Rev. 0 | Page 27 of 28
AD9741/AD9743/AD9745/AD9746/AD9747
NOTES
©2007 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D06569-0-5/07(0)
Rev. 0 | Page 28 of 28
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明