ADAV4622BSTZ [ADI]
Audio Processor for Advanced TV with Sound IF Demodulator and Stereo Decoder; 高级电视音频处理器，内置声音IF解调器和立体声解码器
| 型号： | ADAV4622BSTZ |
| 厂家： | 
ADI |
| 描述： | Audio Processor for Advanced TV with Sound IF Demodulator and Stereo Decoder |
| 文件： | 总28页 (文件大小：711K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Audio Processor for Advanced TV with
Sound IF Demodulator and Stereo Decoder
ADAV4622
FEATURES
PRODUCT OVERVIEW
Sound IF (SIF) processor
The ADAV4622 is an enhanced audio processor targeting
SIF demodulator and broadcast stereo decoder
NICAM (BG, DK, I, L), A2 (BG, DK, M), BTSC (M, N), EIAJ (M)
Automatic sound IF standard detection
Fully programmable 28-bit audio processor for enhanced
ATV sound—default TV audio flow loaded on reset
Implements Analog Devices and third-party branded audio
algorithms
Adjustable digital delay line for audio/video
Synchronization for up to 200 ms stereo delay
High performance 24-bit ADC and DAC
94 dB DNR performance on DAC channels
95 dB DNR performance on ADC channels
Dual headphone outputs with integrated amplifiers
High performance pulse-width modulation (PWM) digital
outputs
advanced TV applications with full support for digital and
analog baseband audio as well as multistandard broadcast SIF
demodulation and decoding.
The audio processor, by default, loads a dedicated TV audio
flow that incorporates full matrix switching (any input to any
output), automatic volume control that compensates for volume
changes during advertisements or when switching channels,
dynamic bass, a multiband equalizer, and up to 200 ms of stereo
delay memory for audio-video synchronization.
Alternatively, Analog Devices, Inc., offers an award-winning
graphical programming tool (SigmaStudio™) that allows custom
flows to be quickly developed and evaluated. This allows the
creation of customer-specific audio flows, including use of the
Analog Devices library of third-party algorithms.
Multichannel digital baseband I/O
The analog I/O integrates Analog Devices proprietary
continuous-time, multibit Σ-Δ architecture to bring a higher
level of performance to ATV systems, required by third-party
algorithm providers to meet system branding certification. The
analog input is provided by 95 dB dynamic range (DNR) ADCs,
and analog output is provided by 94 dB DNR DACs.
4 stereo synchronous digital I2S input channels
One 6-channel sample rate converter (SRC) and one
stereo SRC supporting input sample rates from
5 kHz to 50 kHz
One stereo synchronous digital I2S output
S/PDIF output with S/PDIF input mux capability
Fast I2C control
Operates from 3.3 V (analog), 1.8 V (digital core), and 3.3 V
(digital interface)
The main speaker outputs can be supplied as a digitally
modulated PWM stream to support digital amplifiers.
The ADAV4622 includes multichannel digital inputs and
outputs. In addition, digital input channels can be routed
through integrated sample rate converters (SRC), which are
capable of supporting any arbitrary sample rate from 5 kHz
to 50 kHz.
Available in 80-lead LQFP
APPLICATIONS
General-purpose consumer audio postprocessing
Home audio
DVD recorders
Home theater in a box (HTIB) systems and DVD receivers
Audio processing subsystems for DTV-ready TVs
Analog broadcast capability for iDTVs
Rev. B
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113 ©2008–2009 Analog Devices, Inc. All rights reserved.
ADAV4622
TABLE OF CONTENTS
Features .............................................................................................. 1
VREF............................................................................................ 20
FILTA and FILTD....................................................................... 20
Applications....................................................................................... 1
Product Overview............................................................................. 1
Revision History ............................................................................... 2
Functional Block Diagram .............................................................. 3
Specifications..................................................................................... 4
Performance Parameters ............................................................. 4
Timing Specifications .................................................................. 9
Timing Diagrams........................................................................ 10
Absolute Maximum Ratings.......................................................... 12
Thermal Resistance .................................................................... 12
Thermal Conditions................................................................... 12
ESD Caution................................................................................ 12
Pin Configuration and Function Descriptions........................... 13
Typical Performance Characteristics ........................................... 16
Terminology .................................................................................... 18
Pin Functions .................................................................................. 19
SDIN0, SDIN1, SDIN2, and SDIN3/SPDIF_IN0................... 19
LRCLK0, BCLK0, LRCLK1, BCLK1, LRCLK2, and BCLK2 19
SDO0/AD0 .................................................................................. 19
SPDIF_OUT (SDO1)................................................................. 19
MCLKI/XIN................................................................................ 19
XOUT........................................................................................... 19
MCLK_OUT ............................................................................... 19
SDA............................................................................................... 19
SCL ............................................................................................... 20
PWM1A, PWM1B, PWM2A, PWM2B, PWM3A, PWM3B,
PWM4A, and PWM4B.............................................................. 20
PWM_READY ........................................................................... 20
AVDD .......................................................................................... 20
DVDD.......................................................................................... 20
ODVDD....................................................................................... 20
DGND.......................................................................................... 20
AGND.......................................................................................... 20
ODGND ...................................................................................... 20
SIF_REFP, SIF_REFCM, and SIF_REFN................................ 20
SIF_IN1 and SIF_IN2................................................................ 20
SIF_PGA_REF............................................................................ 20
ISET.............................................................................................. 20
Functional Descriptions ................................................................ 21
SIF Processor............................................................................... 21
Master Clock Oscillator............................................................. 21
I2C Interface ................................................................................ 22
ADC Inputs................................................................................. 22
I2S Digital Audio Inputs ............................................................ 22
DAC Voltage Outputs ................................................................ 23
PWM Outputs ............................................................................ 24
Headphone Outputs................................................................... 24
I2S Digital Audio Outputs ......................................................... 24
S/PDIF Input/Output................................................................. 25
Hardware Mute Control ............................................................ 25
Audio Processor ......................................................................... 25
Graphical Programming Environment ................................... 25
Application Layer ....................................................................... 25
Loading a Custom Audio Processing Flow............................. 26
Outline Dimensions....................................................................... 28
Ordering Guide .......................................................................... 28
MUTE
RESET
.......................................................................................... 20
.......................................................................................... 20
AUXIN1L, AUXIN2L, AUXIN1R, and AUXIN2R................ 20
AUXOUT1L, AUXOUT2L, AUXOUT3L, AUXOUT4L,
AUXOUT1R, AUXOUT2R, AUXOUT3R, and AUXOUT4R
....................................................................................................... 20
HPOUT1L, HPOUT2L, HPOUT1R, and HPOUT2R .......... 20
PLL_LF......................................................................................... 20
Change to Hardware Mute Control, Graphical Programming
Environment, and Application Layer Sections........................... 25
Changes to Ordering Guide.......................................................... 28
11/08—Revision A: Initial Version
REVISION HISTORY
7/09—Rev. A to Rev. B
Added Advantiv Logo ...................................................................... 1
Change to PWM Outputs Section................................................ 24
Rev. B | Page 2 of 28
ADAV4622
FUNCTIONAL BLOCK DIAGRAM
SDO0/AD0
DIGITAL
OUTPUTS
BCLK1
SIF_IN1
SIF_IN2
LRCLK1
SIF PROCESSOR
SPDIF_IN0
SPDIF_IN1
SPDIF_IN2
SPDIF_IN3
SPDIF_IN4
SPDIF_IN5
SPDIF_IN6
MCLK_OUT
SYSTEM
CLOCKS
MCLKI/XIN
XOUT
PLL
S/PDIF I/O
SPDIF_OUT/SDO1
SCL
SDA
2
I C INTERFACE
AUDIO
PROCESSOR
PWM1A
PWM1B
PWM2A
PWM2B
PWM3A
PWM3B
PWM4A
PWM4B
AD0
MUTE
PWM
DIGITAL
OUTPUT
2-CHANNEL SRC
ASYNCHRONOUS
DIGITAL INPUT
BCLK2
LRCLK2
BCLK1
LRCLK1
PWM_READY
6-CHANNEL SRC
ASYNCHRONOUS
DIGITAL INPUT
BCLK0
LRCLK0
AUXOUT4L
AUXOUT4R
HPOUT1L
DAC
DAC
DAC
HPOUT1R
SDIN0
SDIN1
SDIN2
SDIN3
SYNCHRONOUS
MULTICHANNEL
DIGITAL INPUTS
AUXOUT1L
AUXOUT1R
AUXOUT2L
AUXOUT2R
AUXIN1L
AUXIN1R
ADC
ADC
HPOUT2L
HPOUT2R
AUXIN2L
AUXIN2R
A-V
SYNCHRONOUS
DELAY
AUXOUT3L
AUXOUT3R
MEMORY
DAC
ADAV4622
Figure 1. ADAV4622 with PWM-Based Speaker Outputs
Rev. B | Page 3 of 28
ADAV4622
SPECIFICATIONS
AVDD = 3.3 V, DVDD = 1.8 V, ODVDD = 3.3 V, operating temperature = −40°C to +85°C, master clock = 24.576 MHz, measurement
bandwidth = 20 Hz to 20 kHz, ADC input signal = DAC output signal = 1 kHz, unless otherwise noted.
PERFORMANCE PARAMETERS
Table 1.
Parameter
Min
Typ
Max
Unit
Test Conditions/Comments
SIF ADC INPUT SECTION
Analog Input Frequency Range
Recommended Analog Input Level
Maximum Analog Input Range
Input Impedance
10
MHz
dBu
V p-p
kΩ
90 18 dB
FM, AGC in PGA priority mode
Default setting
1.6
12
6
PGA Gain = 0 dB
KΩ
PGA Gain = 10 dB
2.3
1.9
60
32
kΩ
PGA Gain = 20 dB
DC Bias Level
V
SIF Input Isolation
FM Limiting Sensitivity
dB
SIF_IN1 to SIF_ IN2
dBu
A2 (DK), Mono, deviation mode = 100%, fFM = 400 Hz,
Δf = 50 kHz, BW = 20 Hz to 15 kHz, rms detector
31
31
34
dBu
dBu
dBu
A2 (I), Mono, deviation mode = 100%, fFM = 400 Hz,
Δf = 50 kHz, BW = 20 Hz to 15 kHz, rms detector
A2 (BG), Mono, deviation mode = 100%, fFM = 400 Hz,
Δf = 50 kHz, BW = 20 Hz to 15 kHz, rms detector
BTSC (M, N), Mono, deviation mode = 100%,
f
FM = 400 Hz, Δf = 25 kHz, BW = 20 Hz to 15 kHz,
rms detector
28.5
30
dBu
A2 (M), Mono, deviation mode = 100%, fFM = 400 Hz,
Δf = 25 kHz, BW = 20 Hz to 15 kHz, rms detector
dBu
EIAJ (M), Mono, deviation mode = 100%, fFM = 400 Hz,
Δf = 25 kHz, BW = 20 Hz to 15 kHz, rms detector
FM Output Level at 25% Deviation Mode
FM Output Level at 50% Deviation Mode
FM Output Level at 100% Deviation Mode
FM Output Level at 200% Deviation Mode
53.7
53.6
56.3
56.7
53.7
53.6
56.3
56.7
53.7
53.6
56.3
56.7
53.7
53.6
56.3
56.7
% FS
% FS
% FS
% FS
% FS
% FS
% FS
% FS
% FS
% FS
% FS
% FS
% FS
% FS
% FS
% FS
A2 (DK, I, BG), Mono, VSIF = 100 mV, fFM = 400 Hz,
Δf = 12.5 kHz, rms detector
BTSC (M, N), Mono, VSIF = 100 mV, fFM = 400 Hz,
Δf = 6.25 kHz, rms detector
A2 (M), Mono, VSIF = 100 mV, fFM = 400 Hz,
Δf = 6.25 kHz, rms detector
EIAJ (M), Mono, VSIF = 100 mV, fFM = 400 Hz,
Δf = 6.25 kHz, rms detector
A2 (DK, I, BG), Mono, VSIF = 100 mV, fFM = 400 Hz,
Δf = 25 kHz, rms detector
BTSC (M, N), Mono, VSIF = 100 mV, fFM = 400 Hz,
Δf = 12.5 kHz, rms detector
A2 (M), Mono, VSIF = 100 mV, fFM = 400 Hz,
Δf = 12.5 kHz, rms detector
EIAJ (M), Mono, VSIF = 100 mV, fFM = 400 Hz,
Δf = 12.5 kHz, rms detector
A2 (DK, I, BG), Mono, VSIF = 100 mV, fFM = 400 Hz,
Δf = 50 kHz, rms detector
BTSC (M, N), Mono, VSIF = 100 mV, fFM = 400 Hz,
Δf = 25 kHz, rms detector
A2 (M), Mono, VSIF = 100 mV, fFM = 400 Hz, Δf = 25 kHz,
rms detector
EIAJ (M), Mono, VSIF = 100 mV, fFM = 400 Hz, Δf = 25 kHz,
rms detector
A2 (DK, I, BG), Mono, VSIF =100 mV, fFM = 400 Hz,
Δf = 100 kHz, rms detector
BTSC (M, N), Mono, VSIF = 100 mV, fFM = 400 Hz,
Δf = 50 kHz, rms detector
A2 (M), Mono, VSIF = 100 mV, fFM = 400 Hz, Δf = 50 kHz,
rms detector
EIAJ (M), Mono, VSIF = 100 mV, fFM = 400 Hz, Δf = 50 kHz,
rms detector
Rev. B | Page 4 of 28
ADAV4622
Parameter
FM Output Level at 400% Deviation Mode
Min
Typ
Max
Unit
Test Conditions/Comments
53.7
% FS
A2 (DK, I, BG), Mono, VSIF = 100 mV, fFM = 400 Hz,
Δf = 200 kHz, rms detector
53.6
56.4
56.7
53.7
53.6
56.3
56.7
69.5
% FS
% FS
% FS
% FS
% FS
% FS
% FS
dB
BTSC (M, N), Mono, VSIF = 100 mV, fFM = 400 Hz,
Δf = 100 kHz, rms detector
A2 (M), Mono, VSIF = 100 mV, fFM = 400 Hz,
Δf = 100 kHz, rms detector
EIAJ (M), Mono, VSIF = 100 mV, fFM = 400 Hz, Δf = 100 kHz,
rms detector
FM Output Level at 800% Deviation Mode
A2 (DK, I, BG), Mono, VSIF = 100 mV, fFM = 400 Hz,
Δf = 400 kHz, rms detector
BTSC (M, N), Mono, VSIF = 100 mV, fFM = 400 Hz,
Δf = 200 kHz, rms detector
A2 (M), Mono, VSIF = 100 mV, fFM = 400 Hz,
Δf = 200 kHz, rms detector
EIAJ (M), Mono, VSIF = 100 mV, fFM = 400 Hz,
Δf = 200 kHz, rms detector
AM Rejection Ratio
A2 (DK), Mono, deviation mode = 100%, VSIF = 100 mV,
f
FM = 400 Hz, Δf = 27 kHz, fAM = 400 Hz, MODAM = 30%,
BW = 20 Hz to 15 kHz, rms detector
70
dB
A2 (I), Mono, deviation mode = 100%, VSIF = 100 mV,
fFM = 400 Hz, Δf = 27 kHz, fAM = 400 Hz, MODAM = 30%,
BW = 20 Hz to 15 kHz, rms detector
70
dB
A2 (BG), Mono, deviation mode = 100%, VSIF = 100 mV,
fFM = 400 Hz, Δf = 27 kHz, fAM = 400 Hz, MODAM = 30%,
BW = 20 Hz to 15 kHz, rms detector
70.5
40
dB
Mono (M), deviation mode = 100%, VSIF = 100 mV,
fFM = 400 Hz, Δf = 13.5 kHz, fAM = 400 Hz, MODAM = 30%,
BW = 20 Hz to 15 kHz, rms detector
AM Sensitivity
dBu
Mono (L), fAM = 400 Hz, MOD = 30%, BW = 20 Hz to 15 kHz,
rms detector, (S + N)/N = 10 dB
BTSC (M) PERFORMANCE
Measured at analog audio output, video = 75% color bar,
fSC = 4.5 MHz, fFM = 1 kHz, Δf = 25 kHz (100%), deemphasis =
75 μs, measuring BW = 20 Hz to 15 kHz with dBX NR
Dynamic Range
Stereo Channel
62
68
dB
dB
Stereo L or R (L = −R), 100%, 1 kHz
SAP channel with Mono 100%, 1 kHz
SAP Channel
Total Harmonic Distortion + Noise
Stereo Channel
−46
−40
dB
dB
Stereo L or R (L = −R), 100%, 1 kHz
SAP 100%, 1 kHz
SAP Channel
Frequency Response
Stereo Channel
fFM = 20 Hz to 12 kHz
+0.1/−0.7
+2.5/−2.5
dB
dB
Stereo L or R, 50%, (L = −R)
SAP 50%, Mono 100%, 1 kHz
SAP Channel
Crosstalk
Stereo-to-SAP Channel
SAP-to-Stereo Channel
Stereo Separation dBX
EIAJ (M) PERFORMANCE
−74
−71
30
dB
dB
dB
L or R 50%, 1 kHz
SAP 50%, 1 kHz
L off, R 50%, 1 kHz
Measured at analog audio output, video = 75% color bar,
f
SC = 4.5 MHz, fFM = 1 kHz, Δf = 25 kHz (100%),
deemphasis = 75 μs, measuring BW = 20 Hz to 15 kHz
Dynamic Range
Stereo Channel
58
56
dB
dB
Stereo L or R, 100%, 1 kHz
Dual Channel
Dual channel with Mono 100%, 1 kHz
Total Harmonic Distortion + Noise
Stereo Channel
−56
−47
dB
dB
Stereo L or R, 100%, 1 kHz
Dual 50%, 1 kHz
Dual Channel
Frequency Response
Stereo Channel
fFM = 20 Hz to 10 kHz
Stereo L or R, 100%
+0.03/−0.53
+0.17/−1.4
dB
dB
Dual Channel
Dual 100%, Mono 100%, 1 kHz
Crosstalk
Main-to-Dual Channel
Dual-to-Main Channel
Stereo Separation
−75
−83
39
dB
dB
dB
Main 100%, 1 kHz
Dual 100%, 1 kHz
Stereo L or R, 100%, 1 kHz
Rev. B | Page 5 of 28
ADAV4622
Parameter
Min
Typ
Max
Unit
Test Conditions/Comments
A2 (M) PERFORMANCE
Measured at analog audio output, video = 75% color bar,
fSC1 = 4.5 MHz, fSC2 = 4.724 MHz, fFM = 1 kHz, Δf = 25 kHz
(100%), deemphasis = 75 μs, measuring BW = 20 Hz to
15 kHz
Dynamic Range
60
dB
dB
dB
dB
dB
Mono 100%, 1 kHz
Total Harmonic Distortion + Noise
Frequency Response
−64
Mono 100%, 1 kHz
+0.4/−0.05
Mono 100%, fFM = 25 Hz to 15 kHz
Mono or dual off, 100%, 1 kHz
Stereo L off, R 50%, 1 kHz
Crosstalk (Dual)
−88
66
Channel Separation (Stereo)
A2 (DK1/DK2/DK3) PERFORMANCE
Measured at analog audio output, video = 75% color bar,
f
f
SC1 = 6.5 MHz, fSC2 = 6.742 MHz, (DK2 worst case),
FM = 1 kHz, Δf = 50 kHz (100%), deemphasis = 50 μs,
measuring BW = 20 Hz to 15 kHz
Dynamic Range
74
dB
dB
dB
dB
dB
Mono 100%, 1 kHz
Total Harmonic Distortion + Noise
Frequency Response
−66
Mono 100%, 1 kHz
+0.1/−0.3
Mono 100%, fFM = 20 Hz to 15 kHz
Mono or dual off, 100%, 1 kHz
Stereo L off, R 50%, 1 kHz
Crosstalk (Dual)
−88
77
Channel Separation (Stereo)
A2 (BG) PERFORMANCE
Measured at analog audio output, video = 75% color bar,
fSC1 = 5.5 MHz, fSC2 = 5.742 MHz, fFM = 1 kHz,
Δf = 50 kHz (100%), deemphasis = 50 μs,
measuring BW = 20 Hz to 15 kHz
Dynamic Range
74
dB
dB
dB
dB
dB
Mono 100%, 1 kHz
Total Harmonic Distortion + Noise
Frequency Response
−61
Mono 100%, 1 kHz
+0.1/−0.3
Mono 100%, fFM = 25 Hz to 15 kHz
Mono or dual off, 100%, 1 kHz
Stereo L off, R 50%, 1 kHz
Crosstalk (Dual)
−89
70
Channel Separation (Stereo)
NICAM (I) PERFORMANCE
Measured at analog audio output, video = 75% color bar,
1 kHz, unweighted, deemphasis = J17, measuring BW = 20
Hz to 15 kHz
Dynamic Range
72
dB
dB
dB
dB
dB
Stereo L or R, 0 dB, 1 kHz
Stereo L or R, 0 dB, 1 kHz
Stereo L or R, 0 dB
Total Harmonic Distortion + Noise
Frequency Response
Crosstalk
−63
−1.3/+0.07
−80
73
0
Mono or dual, 0 dB, 1 kHz
L or R, 0 dB, 1 kHz
Stereo Separation
Bit Error Rate
FM and NICAM nominal conditions
NICAM (BG, DK, L) PERFORMANCE
Measured at analog audio output, video = 75% color bar,
1 kHz, unweighted, deemphasis = J17, measuring BW =
20 Hz to 15 kHz
Dynamic Range
Total Harmonic Distortion + Noise
Frequency Response
Crosstalk
72
dB
dB
dB
dB
dB
Stereo L or R, 0 dB, 1 kHz
Stereo L or R, 0 dB, 1 kHz
Stereo L or R, 0 dB
−63
−1.3/+0.07
−80
74
0
Mono or dual, 0 dB, 1 kHz
L or R, 0 dB, 1 kHz
Stereo Separation
Bit Error Rate
FM and NICAM nominal conditions
AM PERFORMANCE
Measured at analog audio output, 1 kHz,
AM carrier 6.5 MHz measuring BW = 20 Hz to 15 kHz
Dynamic Range
RMS/FLAT
55
dB
dB
dB
dB
AM = 54% modulation
QP/CCIR
35
CCIR filter, AM = 54% modulation
AM = 54% modulation
Total Harmonic Distortion + Noise
Frequency Response
REFERENCE SECTION
Absolute Voltage VREF
VREF Temperature Coefficient
−49
+0.03/−1.2
AM = 54% modulation
1.53
100
V
ppm/°C
Rev. B | Page 6 of 28
ADAV4622
Parameter
Min
Typ
Max
Unit
Test Conditions/Comments
ADC SECTION
Number of Channels
Full-Scale Input Level
Resolution
4
Two stereo channels
100
24
μA rms
Bits
Dynamic Range (Stereo Channel)
A-Weighted
95
dB
dB
−60 dBFS with respect to full-scale analog input
−3 dBFS with respect to full-scale analog input
Total Harmonic Distortion + Noise (Stereo
Channel)
−90
Gain Mismatch
0.2
dB
dB
dB
kΩ
Left- and right-channel gain mismatch
Crosstalk (Left to Right, Right to Left)
Gain Error
−110
−1
Input signal is 100 μA rms
Current Setting Resistor (RISET
)
20
External resistor to set current input range of ADC for
nominal 2.0 V rms input signal
Power Supply Rejection
−87
dB
1 kHz, 300 mV p-p signal at AVDD
At 48 kHz, guaranteed by design
ADC DIGITAL DECIMATOR FILTER
CHARACTERISTICS
Pass Band
22.5
kHz
dB
Pass-Band Ripple
0.0002
Stop Band
26.5
100
kHz
dB
Stop-Band Attenuation
Group Delay
1040
μs
PWM SECTION
Frequency
384
kHz
Guaranteed by design
Guaranteed by design
Modulation Index
Dynamic Range
0.976
A-Weighted
98
dB
dB
−60 dB with respect to full-scale code input
−3 dB with respect to full-scale code input
Total Harmonic Distortion + Noise
DAC SECTION
−78
Number of Auxiliary Output Channels
Resolution
8
Four stereo channels
24
1
Bits
Full-Scale Analog Output
Dynamic Range
V rms
A-Weighted
94
dB
dB
dB
dB
dB
V
−60 dBFS with respect to full-scale code input
−3 dBFS with respect to full-scale code input
Total Harmonic Distortion + Noise
Crosstalk (Left to Right, Right to Left)
Interchannel Gain Mismatch
Gain Error
−86
−102
0.1
Left- and right-channel gain mismatch
1 V rms output
0.525
1.53
−90
235
DC Bias
Power Supply Rejection
Output Impedance
dB
Ω
1 kHz, 300 mV p-p signal at AVDD
At 48 kHz, guaranteed by design
DAC DIGITAL INTERPOLATION FILTER
CHARACTERISTICS
Pass Band
21.769
0.01
kHz
dB
Pass-Band Ripple
Transition Band
23.95
26.122
75
kHz
kHz
dB
Stop Band
Stop-Band Attenuation
Group Delay
580
μs
HEADPHONE AMPLIFIER
Number of Channels
Full-Scale Output Power
Dynamic Range
Measured at headphone output with 32 Ω load
Two stereo channels
4
31
mW rms
1 V rms output
A-Weighted
93
dB
dB
dB
V
−60 dBFS with respect to full-scale code input
−3 dBFS with respect to full-scale code input
Total Harmonic Distortion + Noise
Interchannel Gain Mismatch
DC Bias
−83
0.1
1.53
−85
Power Supply Rejection
dB
1 kHz, 300 mV p-p signal at AVDD
Rev. B | Page 7 of 28
ADAV4622
Parameter
Min
Typ
Max
Unit
Test Conditions/Comments
SRC
Number of Channels
Dynamic Range
A-Weighted
8
Two channels (SRC1), six channels (SRC2)
115
dB
−60 dBFS input (worst-case input fS = 50 kHz)
−3 dBFS input (worst-case input fS = 50 kHz)
Total Harmonic Distortion + Noise
Sample Rate
−113
dB
5
50
kHz
SRC DIGITAL INTERPOLATION FILTER
CHARACTERISTICS
At 48 kHz, guaranteed by design
Pass Band
21.678
0.005
26.232
110
kHz
dB
Pass-Band Ripple
Stop Band
kHz
dB
Stop-Band Attenuation
Group Delay
876
μs
DIGITAL INPUT/OUTPUT
Input Voltage High (VIH)
Input Voltage Low (VIL)
Input Leakage
2.0
ODVDD
0.8
V
V
IIH (SDIN0, SDIN1, SDIN2, SDIN3, LRCLK0,
LRCLK1, LRCLK2, BCLK0, BCLK1, BCLK2,
SPDIF_OUT, SPDIF_IN)
40
μA
V
IH = ODVDD, equivalent to a 90 kΩ pull-up resistor
IH = ODVDD, equivalent to a 266 kΩ pull-up resistor
RESET
)
13.5
−40
μA
μA
V
V
IIH
(
IIL (SDO0, SCL, SDA)
VIL = 0 V, equivalent to a 90 kΩ pull-down resistor
Output Voltage High (VOH
)
2.4
1.4
IOH = 0.4 mA
IOL = −2 mA
IOH = 0.4 mA
IOL = −3.2 mA
Output Voltage Low (VOL
)
0.4
0.4
V
Output Voltage High (VOH) (MCLK_OUT)
Output Voltage Low (VOL) (MCLK_OUT)
Input Capacitance
V
V
10
pF
SUPPLIES
Analog Supplies (AVDD)
Digital Supplies (DVDD)
Interface Supply (ODVDD)
Supply Currents
3.0
3.3
3.6
2.0
3.6
V
V
V
1.65 1.8
3.0
3.3
MCLK = 24 MHz, ADCs and DACs active, headphone
outputs active and driving a 16 Ω load
Analog Current
Digital Current
260
350
2
mA
mA
mA
W
Interface Current
Power Dissipation
Standby Currents
1.495
RESET
ADC, DAC, and headphone outputs floating,
MCLK = 24 MHz
low,
Analog Current
Digital Current
10
4
mA
mA
mA
Interface Current
1.6
TEMPERATURE RANGE
Operating Temperature
Storage Temperature
−40
−65
+85
°C
°C
+150
Rev. B | Page 8 of 28
ADAV4622
TIMING SPECIFICATIONS
Table 2.
Parameter
Description
Min
Max
Unit
Comments
MASTER CLOCK AND RESET
fMCLKI
tMCH
tMCL
MCLKI frequency
MCLKI high
MCLKI low
3.072
10
10
24.576
MHz
ns
ns
tRESET
RESET low
200
ns
MASTER CLOCK OUTPUT
tJIT
tCH
tCL
Period jitter
MCLK_OUT high
MCLK_OUT low
800
55
55
ps
%
%
45
45
I2C PORT
fSCL
tSCLH
tSCLL
SCL clock frequency
SCL high
SCL low
400
kHz
ns
μs
600
1.3
Start Condition
tSCS
tSCH
tDS
tSCR
tSCF
tSDR
tSDF
Setup time
Hold time
600
600
100
ns
ns
ns
ns
ns
ns
ns
Relevant for repeated start condition
After this period, the first clock is generated
Data setup time
SCL rise time
SCL fall time
SDA rise time
SDA fall time
300
300
300
300
Stop Condition
tSCS
Setup time
0
ns
SERIAL PORTS
Slave Mode
tSBH
tSBL
BCLK high
BCLK low
40
40
ns
ns
fSBF
tSLS
tSLH
tSDS
BCLK frequency
LRCLK setup
LRCLK hold
SDIN setup
SDIN hold
64 × fS
10
10
10
10
ns
ns
ns
ns
ns
To BCLK rising edge
From BCLK rising edge
To BCLK rising edge
From BCLK rising edge
From BCLK falling edge
tSDH
tSDD
SDO delay
50
Master Mode
tMLD
tMDD
tMDS
tMDH
LRCLK delay
SDO delay
SDIN setup
SDIN hold
25
15
ns
ns
ns
ns
From BCLK falling edge
From BCLK falling edge
From BCLK rising edge
From BCLK rising edge
10
10
Rev. B | Page 9 of 28
ADAV4622
TIMING DIAGRAMS
tMP = 1/fMCLKI
MCLKI
RESET
tRESET
Figure 2. Master Clock and Reset Timing
tJIT
DVDD
GND
tCH
tCL
tCK
Figure 3. Master Clock Output Timing
tSLH
LRCLK1
BCLK1
SDINx
tSLS
tSDS tSDH
SDO0
tSDD
Figure 4. Serial Port Slave Mode Timing
tMLD
LRCLK1
BCLK1
SDINx
tMDS tMDH
SDO0
tMDD
Figure 5. Serial Port Master Mode Timing
100µA
I
OL
TO OUTPUT
PIN
ODVDD
50pF
100µA
I
OH
Figure 6. Load Circuit for Digital Output Timing Specifications
Rev. B | Page 10 of 28
ADAV4622
1.8V
1.65V
DVDD
0.18V
0V
1.0s MAX
3.3V
3.0V
AVDD
ODVDD
0.33V
0V
1.0s MAX
Figure 7. Power-Up Sequence Timing
1.8V
0V
1.65V
DVDD
0.18V
1.0s MAX
3.3V
0V
3.0V
AVDD
ODVDD
0.33V
1.0s MAX
Figure 8. Power-Down Sequence Timing
Rev. B | Page 11 of 28
ADAV4622
ABSOLUTE MAXIMUM RATINGS
THERMAL RESISTANCE
Table 3.
θJA is specified for the worst-case conditions, that is, a device
soldered in a circuit board for surface-mount packages.
Parameter
Rating
DVDD to DGND
ODVDD to DGND
AVDD to AGND
AGND to DGND
Digital Inputs
Analog Inputs
Reference Voltage
Soldering (10 sec)
0 V to 2.2 V
0 V to 4 V
0 V to 4 V
−0.3 V to +0.3 V
DGND − 0.3 V to ODVDD + 0.3 V
AGND − 0.3 V to AVDD + 0.3 V
Indefinite short circuit to ground
300°C
Table 4. Thermal Resistance1
Package Type
θJA
θJC
Unit
80-Lead LQFP
38.1
7.6
°C/W
1 Based on JEDEC 2S2P PCB.
THERMAL CONDITIONS
To ensure correct operation of the device, the case temperature
(TCASE) must be kept below 121°C to keep the junction tempera-
ture (TJ) below the maximum allowed, 125°C.
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
Rev. B | Page 12 of 28
ADAV4622
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61
1
2
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
FILTA
VREF
HPOUT2L
AVDD
PIN 1
3
AGND
HPOUT1R
HPOUT1L
AGND
4
AVDD
5
SIF_REFP
SIF_REFCM
SIF_REFN
SIF_IN1
6
AGND
7
PLL_LF
AVDD
8
ADAV4622
TOP VIEW
(Not to Scale)
9
SIF_PGA_REF
SIF_IN2
DGND
10
11
12
13
14
15
16
17
18
19
20
DVDD
AGND
RESET
PWM4B
PWM4A
PWM3B
PWM3A
PWM2B
PWM2A
PWM1B
PWM1A
DGND
AVDD
DGND
DVDD
MUTE
SDA
SCL
SPDIF_IN5/LRCLK2
SPDIF_IN6/BCLK2
DGND
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
NC = NO CONNECT
Figure 9. Pin Configuration
Table 5. Pin Function Descriptions
Pin No.
Mnemonic
Description
1
FILTA
ADC Filter Capacitor.
2
VREF
Reference Capacitor.
3
AGND
ADC Ground.
4
AVDD
ADC Supply (3.3 V).
5
6
7
8
SIF_REFP
SIF_REFCM
SIF_REFN
SIF_IN1
SIF_PGA_REF
SIF_IN2
AGND
AVDD
DGND
DVDD
MUTE
SIF ADC Positive Reference (Typical 1.4 V).
SIF ADC Common-Mode Reference (Typical 1 V).
SIF ADC Negative Reference (Typical 0.6 V).
SIF Input 1.
SIF PGA Reference.
SIF Input 2.
SIF AGND.
SIF Supply (3.3 V).
Digital Ground.
Digital Supply (1.8 V).
Active Low Mute Request Input Signal.
9
10
11
12
13
14
15
Rev. B | Page 13 of 28
ADAV4622
Pin No.
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
Mnemonic
Description
SDA
SCL
I2C Data.
I2C Clock.
SPDIF_IN5/LRCLK2
SPDIF_IN6/BCLK2
DGND
DVDD
SDIN0
SDIN1
SDIN2
SPDIF_IN0/SDIN3
SPDIF_IN1/LRCLK0
SPDIF_IN2/BCLK0
ODGND
ODVDD
MCLK_OUT
DVDD
DGND
MCLKI/XIN
XOUT
SPDIF_IN4/BCLK1
SPDIF_IN3/LRCLK1
SDO0/AD0
External Input to S/PDIF Mux/Left/Right Clock for SRC2 (Default).
External Input to S/PDIF Mux/Bit Clock for SRC2 (Default).
Digital Ground.
Digital Supply (1.8 V).
Serial Data Input 0/SRC Data Input.
Serial Data Input 1/SRC Data Input.
Serial Data Input 2/SRC Data Input.
External Input to S/PDIF Mux/SRC Data Input/Serial Data Input 3 (Default).
External Input to S/PDIF Mux/Left/Right Clock for SRC1 (Default).
External Input to S/PDIF Mux/Bit Clock for SRC1 (Default).
Digital Ground.
Digital Interface Supply (3.3 V).
Master Clock Output.
Digital Supply (1.8 V).
Digital Ground.
Master Clock/Crystal Input.
Crystal Output.
External Input to S/PDIF Mux/Bit Clock for Serial Data I/O (Default).
External Input to S/PDIF Mux/Left/Right Clock for Serial Data I/O (Default).
Serial Data Output. This pin acts as the I2C address select on reset. It has an internal pull-down
resistor.
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
SPDIF_OUT/SDO1
PWM_READY
DVDD
Output of S/PDIF Mux/Serial Data Output.
PWM Ready Flag.
Digital Supply (1.8 V).
DGND
Digital Ground.
PWM1A
PWM1B
PWM2A
PWM2B
PWM3A
PWM3B
PWM4A
PWM4B
RESET
Pulse-Width Modulated Output 1A.
Pulse-Width Modulated Output 1B.
Pulse-Width Modulated Output 2A.
Pulse-Width Modulated Output 2B.
Pulse-Width Modulated Output 3A.
Pulse-Width Modulated Output 3B.
Pulse-Width Modulated Output 4A.
Pulse-Width Modulated Output 4B.
Reset Analog and Digital Cores.
Digital Supply (1.8 V).
DVDD
DGND
AVDD
PLL_LF
AGND
AGND
HPOUT1L
HPOUT1R
AVDD
HPOUT2L
HPOUT2R
AUXOUT3L
AUXOUT3R
AUXOUT4L
AUXOUT4R
NC
Digital Ground.
PLL Supply (3.3 V).
PLL Loop Filter.
PLL Ground.
Headphone Driver Ground.
Left Headphone Output 1.
Right Headphone Output 1.
Headphone Driver Supply (3.3 V).
Left Headphone Output 2.
Right Headphone Output 2.
Left Auxiliary Output 3.
Right Auxiliary Output 3.
Left Auxiliary Output 4.
Right Auxiliary Output 4.
No Connection to this Pin Allowed.
DAC Filter Capacitor.
FILTD
Rev. B | Page 14 of 28
ADAV4622
Pin No.
68
69
Mnemonic
AVDD
AGND
Description
DAC Supply (3.3 V).
DAC Ground.
70
AGND
DAC Ground.
71
72
73
74
75
76
77
78
AVDD
DAC Supply (3.3 V).
Left Auxiliary Output 1.
Right Auxiliary Output 1.
Left Auxiliary Output 2.
Right Auxiliary Output 2.
Left Auxiliary Input 2.
Right Auxiliary Input 2.
Left Auxiliary Input 1.
Right Auxiliary Input 1.
ADC Current Setting.
AUXOUT1L
AUXOUT1R
AUXOUT2L
AUXOUT2R
AUXIN2L
AUXIN2R
AUXIN1L
AUXIN1R
ISET
79
80
Rev. B | Page 15 of 28
ADAV4622
TYPICAL PERFORMANCE CHARACTERISTICS
0
0
–30
–20
–60
–40
–90
–60
–120
–150
–180
–210
–240
–270
–300
–80
–100
–120
–140
–160
–180
0
192
384
576
768
0
128
256
384
FREQUENCY (kHz)
FREQUENCY (kHz)
Figure 10. DAC Composite Filter Response (48 kHz)
Figure 13. ADC Composite Filter Response (48 kHz)
0
–20
0
–30
–60
–40
–60
–80
–90
–100
–120
–140
–160
–120
–150
–180
0
24
48
72
96
0
24
48
72
96
FREQUENCY (kHz)
FREQUENCY (kHz)
Figure 11. DAC Band-Pass Filter Response (48 kHz)
Figure 14. ADC Band-Pass Filter Response (48 kHz)
0.6
0.4
0.04
0.03
0.02
0.01
0
0.2
0
–0.01
–0.02
–0.03
–0.04
–0.2
–0.4
–0.6
0
8
16
FREQUENCY (kHz)
24
0
8
16
FREQUENCY (kHz)
24
Figure 12. DAC Pass-Band Ripple (48 kHz)
Figure 15. ADC Pass-Band Ripple (48 kHz)
Rev. B | Page 16 of 28
ADAV4622
0
–20
0
–20
–40
–40
–60
–60
–80
–80
–100
–120
–140
–160
–100
–120
–140
–160
0
4000
8000
12000
16000
20000
0
4000
8000
12000
16000
20000
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 19. ADC Total Harmonic Distortion + Noise
Figure 16. DAC Dynamic Range
0
–20
0
–20
–40
–40
–60
–60
–80
–80
–100
–120
–140
–160
–100
–120
–140
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
0
4000
8000
12000
16000
20000
NORMALIZED FREQUENCY
FREQUENCY (Hz)
Figure 17. DAC Total Harmonic Distortion + Noise
Figure 20. Sample Rate Converter Transfer Function
0
–20
–40
–60
–80
–100
–120
–140
–160
0
4000
8000
12000
16000
20000
FREQUENCY (Hz)
Figure 18. ADC Dynamic Range
Rev. B | Page 17 of 28
ADAV4622
TERMINOLOGY
Power Supply Rejection
Dynamic Range
With no analog input, the signal present at the output when a
300 mV p-p signal is applied to power supply pins, expressed
in decibels of full scale.
The ratio of a full-scale input signal to the integrated input
noise in the pass band (20 Hz to 20 kHz), expressed in decibels
(dB). Dynamic range is measured with a −60 dB input signal
and is equal to (S/[THD+N]) + 60 dB. Note that spurious
harmonics are below the noise with a −60 dB input, so the noise
level establishes the dynamic range. The dynamic range is
specified with and without an A-weight filter applied.
Group Delay
Intuitively, the time interval required for an input pulse to
appear at the converter’s output, expressed in milliseconds (ms).
More precisely, the derivative of radian phase with respect to
radian frequency at a given frequency.
Pass Band
The region of the frequency spectrum unaffected by the
SIF Input Isolation
attenuation of the digital decimator’s filter.
The level of the crosstalk between the SIF inputs in dB.
Pass-Band Ripple
FM Limiting Sensitivity
The peak-to-peak variation in amplitude response from equal
amplitude input signal frequencies within the pass band,
expressed in decibels.
FM limiting sensitivity is given by the modulated carrier level
that gives half the power to the FM demodulator’s output
amplitude comparing to that when the carrier level satisfies
the demodulator’s limiting level.
Stop Band
The region of the frequency spectrum attenuated by the digital
decimator’s filter to the degree specified by stop-band
attenuation.
Deviation Mode
In some regions, the transmitted signal can deviate from the
specification. In order for the ADAV4622 to decode these high
deviation signals correctly, the appropriate modulation level
must be selected.
Gain Error
With a near full-scale input, the ratio of the actual output to the
expected output, expressed in dB.
AM Rejection Ratio
AM rejection ratio is given by the ratio of FM (deviation = 54%)
demodulated audio level vs. residual AM (modulation = 27%)
demodulated audio level at the same carrier level. It is the ability
of the receiver to not mistake an AM signal for an FM signal.
Interchannel Gain Mismatch
With identical near full-scale inputs, the ratio of the outputs of
the two stereo channels, expressed in decibels.
Crosstalk
AM Sensitivity
AM sensitivity is a measure of how well the receiver picks up
very weak AM signals.
Ratio of response on one channel with a grounded input to a
full-scale 1 kHz sine wave input on the other channel, expressed
in decibels.
Rev. B | Page 18 of 28
ADAV4622
PIN FUNCTIONS
Table 5 shows the pin numbers, mnemonics, and descriptions
for the ADAV4622. The input pins have a logic threshold
compatible with 3.3 V input levels.
SDO0/AD0
Serial data output. This pin can output two channels of digital
audio using a variety of standard 2-channel formats. The clocks
for SDO0 are always the same as those used by the synchronous
inputs; this means that LRCLK1 and BCLK1 are used by default,
although SDO0 is capable of using any pair of serial clocks,
LRCLK0/BCLK0, LRCLK1/BCLK1, or LRCLK2/BCLK2.
The serial port control register selects the serial format for the
synchronous output. On reset, the SDO0 pin duplicates as the
I2C® address select pin. In this mode, the logical state of the pin
is polled for four MCLKI cycles following reset. The address
select bit is set as the majority poll of the pin’s logic level after
the four MCLKI cycles.
SDIN0, SDIN1, SDIN2, AND SDIN3/SPDIF_IN0
Serial data inputs. These input pins provide the digital audio
data to the signal processing core. Any of the inputs can be
routed to either of the SRCs for conversion; this input is then
not available as a synchronous input to the audio processor but
only as an input through the selected SRC. The serial format
for the synchronous data is selected by Bits [3:2] of the serial
port control register. If the SRCs are required, the serial format
is selected by Bits [12:9] of the same register. The synchronous
inputs are capable of using any pair of serial clocks LRCLK0/
BCLK0, LRCLK1/BCLK1, or LRCLK2/BCLK2. By default,
they use LRCLK1 and BCLK1. See Figure 24 for more details
regarding the configuration of the synchronous inputs.
SPDIF_OUT (SDO1)
The ADAV4622 contains an S/PDIF multiplexer functionality
that allows the SPDIF_OUT signal to be chosen from an
internally generated S/PDIF signal or from the S/PDIF signal
from an external source, which is connected via one of the
SPDIF_IN pins. This pin can also be configured as an
additional serial data output (SDO1) as an alternate function.
SDIN3 is a shared pin with SPDIF_IN0. If SDIN3 is not in use,
this pin can be used to connect an S/PDIF signal from an
external source, such as an MPEG decoder, to the ADAV4622
on-chip S/PDIF output multiplexer. If SPDIF_OUT is selected
from one of the SPDIF_IN (external) signals, the signal is
simply passed through from input to output.
MCLKI/XIN
Master clock input. The ADAV4622 uses a PLL to generate the
appropriate internal clock for the audio processing core. A clock
signal of a suitable frequency can be connected directly to this
pin, or a crystal can be connected between MCLKI/XIN and
XOUT together with the appropriate capacitors to DGND to
generate a suitable clock signal.
LRCLK0, BCLK0, LRCLK1, BCLK1, LRCLK2, AND
BCLK2
By default, LRCLK1 and BCLK1 are associated with the
synchronous inputs, LRCLK0 and BCLK0 are associated with
SRC1, and LRCLK2 and BCLK2 are associated with SRC2.
However, the SRCs and synchronous inputs can use any of the
serial clocks (see Figure 24 for more details). LRCLK0, BCLK0,
LRCLK1, BCLK1, LRCLK2, and BCLK2 are shared pins with
SPDIF_IN1, SPDIF_IN2, SPDIF_IN3, SPDIF_IN4, SPDIF_IN5,
and SPDIF_IN6, respectively. If LRCLK0/LRCLK1/LRCLK2 or
BCLK0/BCLK1/BCLK2 are not in use, these pins can be used to
connect an S/PDIF signal from an external source, such as an
MPEG decoder, to the ADAV4622 on-chip S/PDIF output
multiplexer. If SPDIF_OUT is selected from one of the
SPDIF_IN (external) signals, the signal is simply passed
through from input to output.
XOUT
This pin is used in conjunction with MCLKI/XIN to generate a
clock signal for the ADAV4622.
MCLK_OUT
This pin can be used to output MCLKI or one of the internal
system clocks. It should be noted that the output level of this
pin is referenced to DVDD (1.8 V) and not ODVDD (3.3 V)
like all other digital inputs and outputs.
SDA
Serial data input for the I2C control port. SDA features a glitch
elimination filter that removes spurious pulses that are less than
50 ns wide.
Rev. B | Page 19 of 28
ADAV4622
SCL
FILTA AND FILTD
Serial clock for the I2C control port. SCL features a glitch
elimination filter that removes spurious pulses that are less
than 50 ns wide.
Decoupling nodes for the ADC and DAC. Decoupling
capacitors should be connected between these nodes and
AGND, typically 47 μF/0.1 μF and 10 μF/0.1 μF, respectively.
MUTE
PWM1A, PWM1B, PWM2A, PWM2B, PWM3A,
PWM3B, PWM4A, AND PWM4B
Mute input request. This active-low input pin controls the
muting of the output ports (both analog and digital) from the
ADAV4622. When low, it asserts mute on the outputs that are
enabled in the audio flow.
Differential pulse-width modulation outputs are suitable for
driving Class-D amplifiers.
PWM_READY
RESET
This pin is set high when PWM is enabled and stable.
RESET
Active-low reset signal. After
goes high, all the circuit
AVDD
blocks are powered down. The blocks can be individually
powered up with software. When the part is powered up, it
takes approximately 3072 internal clocks to initialize the
internal circuitry. The internal system clock is equal to MCLKI
until the PLL is powered and enabled, after which the internal
system clock becomes 2560 × fS (122.88 MHz). Once the PLL
is powered up and enabled after reset, it takes approximately
3 ms to lock. When the audio processor is enabled, it takes
approximately 32,768 internal system clocks to initialize and
load the default flow to the audio processor memory. The audio
processor is not available during this time.
Analog power supply pins. These pins should be connected to
3.3 V. Each pin should be decoupled with 10 μF and 0.1 μF
capacitors to AGND, as close to the pin as possible.
DVDD
Digital power supply. This pin is connected to a 1.8 V digital
supply. Connecting 10 μF and 0.1 μF decoupling capacitors to
DGND, as close to the pin as possible, is strongly recommended
for optimal performance.
ODVDD
Digital interface power supply pin. This pin should be
connected to a 3.3 V digital supply. The pin should be
decoupled with 10 μF and 0.1 μF capacitors to DGND, as
close to the pin as possible.
AUXIN1L, AUXIN2L, AUXIN1R, AND AUXIN2R
Analog inputs to the on-chip ADCs.
AUXOUT1L, AUXOUT2L, AUXOUT3L, AUXOUT4L,
AUXOUT1R, AUXOUT2R, AUXOUT3R, AND
AUXOUT4R
DGND
Digital ground.
Auxiliary DAC analog outputs. These pins can be programmed
to supply the outputs of the internal audio processing for line
out or record use.
AGND
Analog ground.
ODGND
HPOUT1L, HPOUT2L, HPOUT1R, AND HPOUT2R
Ground for the digital interface power supply.
Analog outputs from the headphone amplifiers.
SIF_REFP, SIF_REFCM, AND SIF_REFN
PLL_LF
Decoupling nodes for the SIF block.
PLL loop filter connection. A 100 nF capacitor and a 2 kΩ
resistor in parallel with a 1 nF capacitor tied to AVDD are
required for the PLL loop filter to operate correctly.
SIF_IN1 AND SIF_IN2
Analog inputs for the SIF block.
VREF
SIF_PGA_REF
Voltage reference for DACs and ADCs. This pin is driven by an
internal 1.5 V reference voltage.
PGA reference output. This pin should be decoupled to AGND
with 10 μF and 0.1 μF capacitors.
ISET
ADC current setting resistor.
Rev. B | Page 20 of 28
ADAV4622
FUNCTIONAL DESCRIPTIONS
SIF PROCESSOR
SIF Processor Configuration
The ADAV4622 supports automatic standard detection, which
is enabled by default. The ASD controller configures the SIF
processor with the optimum register settings based on the
detected standard. If the user prefers to operate in manual mode,
or if the user prefers to use an external ASD loop, all of the ASD
status registers are available.
Supported SIF Standards
The ADAV4622 supports all worldwide standards, as shown in
Table 6.
Table 6. ADAV4622 Worldwide SIF Standards
System
Sound
BTSC
BTSC
EIAJ
SC1 (MHz)
SC2 (MHz)
M
N
M
4.5
4.5
4.5
4.5
5.5
5.5
6.0
6.0
6.5
6.5
6.5
6.5
6.5
6.5
–
–
–
MASTER CLOCK OSCILLATOR
Internally, the ADAV4622 operates synchronously to the master
MCLKI input. All internal system clocks are generated from
this single clock input using an internal PLL. This MCLKI input
can also be generated by an external crystal oscillator connected
to the MCLKI/XIN pin or by using a simple crystal resonator
connected across MCLKI/XIN and XOUT. By default, the
master clock frequency is 24.576 MHz; however, by using the
internal dividers, an MCLKI of 12.288 MHz, 6.144 MHz, and
3.072 MHz are also supported.
M
A2
4.724
5.742
5.85
–
6.552
6.258
6.742
5.742
5.85
–
BG
BG
I
A2
NICAM
Mono
NICAM
A2
A2
A2
NICAM
Mono
NICAM
I
DK1
DK2
DK3
DK
L
MASTER CLOCK FREQUENCY
EXTERNAL CLOCK/
OSC
[24.576MHz, 12.288MHz,
6.144MHz, 3.072MHz]
CRYSTAL
L
5.85
SIF Demodulation
Figure 22 shows a block diagram of the SIF demodulation
block. The selected SIF input signal is digitized by an ADC with
a sample rate of 24.576 MHz. An AGC is included to ensure
that for even low level signals, the full range of the ADC is used.
The digitized input is passed to the SIF demodulator for
demodulating. The outputs of the demodulator are then passed
to the internal audio processor. Internally, the audio processor
runs at a 48 kHz sampling frequency. When NICAM is selected,
an internal SRC upsamples the 32 kHz NICAM signal to the
audio processor rate of 48 kHz.
PLL
REFERENCE
CLOCK
3.072MHz
DIVIDER
DIVIDER WORD
[÷8, ÷4, ÷2, ÷1]
2
REGISTER
I C
Figure 21. Master Clock
SC1
SC2
SIF_IN1
A
B
SIF INPUT
4.5MHz ~ 6.742MHz
FM/DQPSK/AM
ADC
SIF_IN2
DEMOD
AGC
SIF
24.576MHz
PARAMETERS
ASD
Figure 22. SIF Demodulation
Rev. B | Page 21 of 28
ADAV4622
I2C INTERFACE
Resistor matching (typically 1%) between RIN and RISET is
important to ensure a full-scale signal on the ADC without
clipping.
The ADAV4622 supports a 2-wire serial (I2C compatible)
microprocessor bus driving multiple peripherals. The
ADAV4622 is controlled by an external I2C master device,
such as a microcontroller. The ADAV4622 is in slave mode
on the I2C bus, except during self-boot. While the ADAV4622
is self-booting, it becomes the master, and the EEPROM, which
contains the ROMs to be booted, is the slave. When the self-
boot process is complete, the ADAV4622 reverts to slave mode
on the I2C bus. No other devices should access the I2C bus while
the ADAV4622 is self-booting (refer to the Application Layer
section and the Loading a Custom Audio Processing Flow
section).
ANALOG INPUT
100µA rms
FULL SCALE
24-BIT
ADC
AUXIN1L
20kΩ
DC BIAS
1.5V
ANALOG INPUT
100µA rms
FULL SCALE
24-BIT
ADC
AUXIN1R
20kΩ
DC BIAS
1.5V
ANALOG INPUT
100µA rms
FULL SCALE
24-BIT
ADC
AUXIN2L
20kΩ
DC BIAS
1.5V
Initially, all devices on the I2C bus are in an idle state, wherein
the devices monitor the SDA and SCL lines for a start condition
and the proper address. The I2C master initiates a data transfer
by establishing a start condition, defined by a high-to-low
transition on SDA while SCL remains high. This indicates that
an address/data stream follows. All devices on the bus respond
to the start condition and read the next byte (7-bit address plus
ANALOG INPUT
100µA rms
FULL SCALE
24-BIT
ADC
AUXIN2R
20kΩ
DC BIAS
1.5V
ISET
ISET
20kΩ
R
Figure 23. Analog Input Section
W
the R/ bit) MSB first. The device that recognizes the transmit-
I2S DIGITAL AUDIO INPUTS
ted address responds by pulling the data line low during the
ninth clock pulse. This ninth bit is known as an acknowledge
bit. All other devices on the bus revert to an idle condition. The
The ADAV4622 has four I2S digital audio inputs that are, by
default, synchronous to the master clock. Also available are two
SRCs capable of supporting any nonsynchronous input with a
sample rate between 5 kHz and 50 kHz. Any of the serial digital
inputs can be redirected through the SRC. Figure 24 shows a
block diagram of the input serial port.
W
R/ bit determines the direction of the data. A Logic Level 0
on the LSB of the first byte means the master writes information
to the peripheral. A Logic Level 1 on the LSB of the first byte
means the master reads information from the peripheral. A data
transfer takes place until a stop condition is encountered. A stop
condition occurs when SDA transitions from low to high while
SCL is held high.
SDIN0
SDIN1
SDIN2
SRC2B
SDIN3
The ADAV4622 determines its I2C device address by sampling
the SDO0 pin after reset. Internally, the SDO0 pin is sampled by
four MCLKI edges to determine the state of the pin (high or
low). Because the pin has an internal pull-down resistor default,
the address of the ADAV4622 is 0x34 (write) and 0x35 (read).
An alternate address, 0x36 (write) and 0x37 (read), is available
by tying the SDO0 pin to ODVDD via a 10 kΩ resistor. The I2C
interface supports a clock frequency up to 400 kHz.
SRC2C
LRCLK0
BCLK0
LRCLK1
BCLK1
LRCLK2
BCLK2
SDIN0
SDIN1
SDIN2
SDIN3
AUDIO
PROCESSOR
LRCLK0
SRC1
ADC INPUTS
BCLK0
LRCLK1
BCLK1
The ADAV4622 has four ADC inputs. By default, these are
configured as two stereo inputs; however, because the audio
processor is programmable, these inputs can be reconfigured.
LRCLK2
BCLK2
SDIN0
SDIN1
SDIN2
The ADC inputs are shown in Figure 23. The analog inputs are
current inputs (100 μA rms FS) with a 1.5 V dc bias voltage.
Any input voltage can be accommodated by choosing a suitable
SRC2A
SRC2B
SRC2C
SDIN3
LRCLK0
BCLK0
SRC2
combination of input resistor (RIN) and ISET resistor (RISET
using the formulas
)
LRCLK1
BCLK1
LRCLK2
BCLK2
R
R
IN = VFS rms/100 μA rms
Figure 24. Digital Input Section
ISET = 2RIN/VIN
Rev. B | Page 22 of 28
ADAV4622
synchronous port; the default clocks in this case are BCLK1 and
LRCLK1.
Synchronous Inputs and Outputs
The synchronous digital inputs and outputs can use any of the
BCLK or LRCLK inputs as a clock and framing signal. By
default, BCLK1 and LRCLK1 are the serial clocks used for the
synchronous inputs. The synchronous port for the ADAV4622
is in slave mode by default, which means the user must supply
the appropriate serial clocks, BCLK and LRCLK. The
synchronous port can also be set to master mode, which means
that the appropriate serial clocks, BCLK and LRCLK, can be
generated internally from the MCLK; therefore, the user does
not need to provide them. The serial data inputs are capable of
accepting all the popular audio transmission standards (see the
Serial Data Interface section for more details).
Serial Data Interface
LRCLK is the framing signal for the left- and right-channel
inputs, with a frequency equal to the sampling frequency (fS).
BCLK is the bit clock for the digital interface, with a frequency
of 64 × fS (32 BCLK periods for each of the left and right
channels).
The serial data interface supports all the popular audio interface
standards, such as I2S, left-justified (LJ), and right-justified (RJ).
The interface mode is software selectable, and its default is I2S.
The data sample width is also software selectable from 16 bits,
20 bits, or 24 bits. The default is 24 bits.
Asynchronous Inputs
I2S Mode
The ADAV4622 has two SRCs, SRC1 and SRC2, that can be
used for converting digital data, which is not synchronous to
the master clock. Each SRC can accept input sample rates in the
range of 5 kHz to 50 kHz. Data that has been converted by the
SRC is inputted to the part and is then synchronous to the
internal audio processor.
In I2S mode, the data are left-justified, MSB first, with the MSB
placed in the second BCLK period following the transition of
the LRCLK. A high-to-low transition of the LRCLK signifies the
beginning of the left-channel data transfer, and a low-to-high
transition on the LRCLK signifies the beginning of the right-
channel data transfer (see Figure 26).
The SRC1 is a 2-channel (single-stereo) sample rate converter
that is capable of using any of the three serial clocks available.
The SRC1 can accept data from any of the serial data inputs
(SDIN0, SDIN1, SDIN2, and SDIN3). Once selected as an input
to the SRC, this SDIN line is assumed to contain asynchronous
data and is then masked as an input to the audio processor to
ensure that asynchronous data is not processed as synchronous
data. By default, SRC1 uses the LRCLK0 and BCLK0 as the
clock and framing signals.
LJ Mode
In LJ mode, the data are left-justified, MSB first, with the MSB
placed in the first BCLK period following the transition of the
LRCLK. A high-to-low transition of the LRCLK signifies the
beginning of the right-channel data transfer, and a low-to-high
transition on the LRCLK signifies the beginning of the left-
channel data transfer (see Figure 27).
RJ Mode
The SRC2 is a 6-channel (3-stereo) sample rate converter that is
capable of using any of the three serial clocks available. The
SRC2 can accept data from any of the serial data inputs (SDIN0,
SDIN1, SDIN2, and SDIN3). Once selected as an input to the
SRC, this SDIN line is assumed to contain asynchronous data
and is then masked internally as an input to the audio processor
to ensure that asynchronous data is not processed as
In RJ mode, the data are right-justified, LSB last, with the LSB
placed in the last BCLK period preceding the transition of
LRCLK. A high-to-low transition of the LRCLK signifies the
beginning of the right-channel data transfer, and a low-to-high
transition on the LRCLK signifies the beginning of the left-
channel data transfer (see Figure 28).
DAC VOLTAGE OUTPUTS
synchronous data. By default, SRC2 uses the LRCLK2 and
BCLK2 as the clock and framing signals.
The ADAV4622 has eight DAC outputs, configured as four stereo
auxiliary DAC outputs. However, because the flow is customiza-
ble, this is programmable. The output level is 1 V rms full scale.
The first output (SRC2A) from SRC2 is always available to the
audio processor. The other two outputs are muxed with two of
the serial inputs before being available to the audio processor.
SRC2B is muxed with SDIN2 and SRC2C is muxed with SDIN3.
By default, these muxes are configured so that the synchronous
inputs are available to the audio processor. The SRC2B and
SRC2C channels can be made available to the audio processor
simply by enabling them by register write.
AUXOUT1L
DAC
DAC
DAC
DAC
AUXOUT1R
AUXOUT2L
AUXOUT2R
AUXOUT3L
AUXOUT3R
When using the ADAV4622 in an asynchronous digital-in-to-
digital-out configuration, the input digital data are input to the
audio processor core from one of the SRCs, using the assigned
BCLK/LRCLK as a framing signal. The digital output is
synchronous to the BCLK/LRCLK, which is assigned to the
AUXOUT4L
AUXOUT4R
Figure 25. DAC Output Section
Rev. B | Page 23 of 28
ADAV4622
LEFT CHANNEL
LRCLK
BCLK
SDO0
RIGHT CHANNEL
LSB
LSB
MSB
MSB
1 /F
S
Figure 26. I2S Mode
RIGHT CHANNEL
LEFT CHANNEL
LRCLK
BCLK
MSB
MSB
LSB
LSB
SDO0
1 /F
S
Figure 27. Left-Justified Mode
RIGHT CHANNEL
LEFT CHANNEL
LRCLK
BCLK
SDO0
MSB
LSB
MSB
LSB
1 /F
S
Figure 28. Right-Justified Mode
PWM OUTPUTS
HEADPHONE OUTPUTS
In the ADAV4622, the main outputs are available as four PWM
output channels, which are suitable for driving Class-D amplifiers.
PWM_Ready is a status pin used to signify that the ADAV4622
PWM outputs are in a valid state. During PWM power-up and
power-down, this pin remains low to signify that the outputs
are not in a valid state. The output power stage should remain
muted until this pin goes high. This functionality helps to
eliminate pop/click and other unwanted noise on the outputs.
There are two stereo headphone amplifier outputs capable
of driving 32 Ω loads at 1 V rms. HPOUT1 is shared with
AUXOUT4, and HPOUT2 is shared with AUXOUT2, as shown
in Figure 30.
AUXOUT4L
PA
HPOUT1L
DAC
HPOUT1R
AUXOUT4R
AUXOUT2L
PA
HPOUT2L
HPOUT2R
+
PWM
MODULATOR
PWM1A
PWM1B
DAC
–
AUXOUT2R
+
–
PWM2A
PWM2B
PWM
MODULATOR
Figure 30. Headphone Outputs Section
+
–
I2S DIGITAL AUDIO OUTPUTS
PWM3A
PWM3B
PWM
MODULATOR
One I2S output, SDO0, uses the same serial clocks as the serial
inputs, which are BCLK1 and LRCLK1 by default. If an addi-
tional digital output is required, an additional pin can be
reconfigured as a serial digital output, as shown in Figure 31.
+
–
PWM4A
PWM4B
PWM
MODULATOR
PWM_READY
Figure 29. PWM Output Section
L
SDO0
Each set of PWM outputs is a complementary output. The
modulation frequency is 384 kHz, and the full-scale duty cycle
has a ratio of 97:3.
R
2
I S OUTPUT
INTERFACE
L
SPDIF_OUT (SDO1)
S/PDIF
OUTPUT
R
Full details on the use of the PWM outputs are available upon
request. Contact a local Analog Devices sales representative for
more details.
BCLK1
LRCLK1
Figure 31. I2S Digital Outputs
Rev. B | Page 24 of 28
ADAV4622
S/PDIF INPUT/OUTPUT
AUDIO PROCESSOR
The S/PDIF output (SPDIF_OUT/SDO1) uses a multiplexer to
select an output from the audio processor or to pass through the
unprocessed SPDIF_IN signals, as shown in Figure 32. On the
ADAV4622, the S/PDIF inputs, SPDIF_IN0/SPDIF_IN1/
SPDIF_IN2/SPDIF_IN3/SPDIF_IN4/SPDIF_IN5/SPDIF_IN6,
are available on the SDIN3, LRCLK0, BCLK0, LRCLK1,
BCLK1, LRCLK2, and BCLK2 pins, respectively. It is possible to
have all seven S/PDIF inputs connected to different S/PDIF
signals at one time. A consequence of this setup is that none of
the LRCLKs and BCLKs are available for use with the digital
inputs SDIN0, SDIN1, SDIN2, and SDIN3. If there is only one
S/PDIF input in use, using the SDIN3 pin as the dedicated
S/PDIF input is recommended; this enables BCLK0/LRCLK0,
BCLK1/LRCLK1, and BCLK2/LRCLK2 to be used as the clock
and framing signal for the synchronous and asynchronous port.
If SDIN3 is used as an S/PDIF input, it should not be used
internally as an input to the audio processor because it contains
invalid data. Similarly, if BCLK or LRCLK are used as S/PDIF
inputs, they can no longer be used as the clock and framing
signals for SDIN0, SDIN1, SDIN2, and SDIN3. The S/PDIF
encoder supports only consumer formats that conform to
IEC-600958.
The internal audio processor runs at 2560 × fS; at 48 kHz, this
is 122.88 MHz. Internally, the word size is 28 bits, which allows
24 dB of headroom for internal processing. Designed specific-
ally with audio processing in mind, it can implement complex
audio algorithms efficiently.
By default, the ADAV4622 loads a default audio flow, as shown
in Figure 34. However, because the audio processor is fully
programmable, a custom audio flow can be quickly developed
and loaded to the audio processor.
The audio flow is contained in program RAM and parameter
RAM. Program RAM contains the instructions to be processed
by the audio processor, and parameter RAM contains the
coefficients that control the flow, such as volume control, filter
coefficients, and enable bits.
GRAPHICAL PROGRAMMING ENVIRONMENT
Custom flows for the ADAV4622 are created in a powerful
drag-and-drop graphical programming application. No knowl-
edge of assembly code is required to program the ADAV4622.
Featuring a comprehensive library of audio processing blocks
(such as filters, delays, dynamics processors, and third-party
algorithms), it allows the quick and simple creation of custom
flows. For debugging purposes, run-time control of the audio
flow allows the user to fully configure and test the created flow.
SDIN3 (SPDIF_IN0)
LRCLK0 (SPDIF_IN1)
BCLK0 (SPDIF_IN2)
LRCLK1 (SPDIF_IN3)
BCLK1 (SPDIF_IN4)
LRCLK2 (SPDIF_IN5)
BCLK2 (SPDIF_IN6)
Training materials and support are available upon request.
Contact a local Analog Devices sales representative for more
details.
APPLICATION LAYER
S/PDIF
ENCODER
SDO1 (SPDIF_OUT)
Unique to this family is the embedded application layer, which
allows the user to define a custom set of registers to control the
audio flow, greatly simplifying the interface between the audio
processor and the system controller.
Figure 32. S/PDIF Output
HARDWARE MUTE CONTROL
The ADAV4622 mute input can be used to mute any of the
MUTE
selected outputs ramp to a muted condition. Unmuting is
Once a custom flow is created, a user-customized register map
can be defined for controlling the flow. Each register is 16 bits,
but controls can use only one bit or all 16 bits. Users have full
control over which parameters they control and the degree of
control they have over those parameters during run time. The
combination of the graphical programming environment and
the powerful application layer allows the user to quickly develop
a custom audio flow and still maintain the usability of a simple
register-based device.
analog or digital outputs. When the
pin goes low, the
handled in one of two ways and depends on the register setting.
MUTE
By default, the
pin going high causes the outputs to
immediately ramp to an unmuted state. However, it is also
possible to have the unmute operation controlled by a control
MUTE
register bit. In this scenario, even if the
pin goes high,
the device does not unmute until a bit in the control register is
set. This can be used when the user wants to keep the outputs
muted, even after the pin has gone high again, for example, in
the case of a fault condition. This allows the system controller
total control over the unmute operation.
Comprehensive documentation on developing a custom audio
flow and the definition and creation of the custom application
layer for the ADAV4622 is available upon request. Contact a
local Analog Devices sales representative for more details.
Full details on register settings and operation of the mute function
are available upon request. Contact a local Analog Devices sales
representative for more details.
Rev. B | Page 25 of 28
ADAV4622
LOADING A CUSTOM AUDIO PROCESSING FLOW
ADDRESS
DATA
The ADAV4622 can load a custom audio flow from an external
I2C ROM. The boot process is initiated by a simple control
register write. The EEPROM device address and the EEPROM
start address for the audio flow ROMs can all be programmed.
AUDIO
PROCESSOR
MEMORY
AUDIO
PROCESSOR
LOAD
LOAD
ON
ON
For the duration of the boot sequence, the ADAV4622 becomes
the master on the I2C bus. Transfer of the ROMs from the
EEPROM to the ADAV4622 takes a maximum of 1.06 sec,
assuming that the full audio processor memory is required,
during which time no other devices should access the I2C bus.
Once the transfer is complete, the ADAV4622 automatically
reverts to slave mode, and the I2C bus master can resume
sending commands.
RESET
COMMAND
DEFAULT
CODE
BOOT-UP
ROM
2
I C PORT
EXTERNAL
CUSTOM
CODE
BOOT-UP ROM
47260 BYTES (MAX)
Figure 33. External EEPROM Booting
Rev. B | Page 26 of 28
ADAV4622
PWM1
(LHIGH)
PWM2
(RHIGH)
BEEPER
PWM3
(LLOW)
AUXIN1L
AUXIN1R
PWM4
(RLOW)
AUXIN2L
AUXIN2R
SDIN0
SUB
CHANNEL
TO INPUT
MUXES
SDIN1
HPOUT1L/
AUXOUT4L
SDIN2/SRC2
CHANNEL B
SDIN3/SRC2
CHANNEL C
HPOUT1R/
AUXOUT4R
SRC1
SRC2
CHANNEL A
AUXOUT2L/
HPOUT2L
AUXOUT2R/
HPOUT2R
S/PDIF OUTL
(SDOL1)
SUB
CHANNEL
S/PDIF OUTR
(SDOR1)
AUXOUT1L
AUXOUT1R
SDOL0
SDOR0
AUXOUT3L
AUXOUT3R
Figure 34. Default Audio Processing Flow
Rev. B | Page 27 of 28
ADAV4622
OUTLINE DIMENSIONS
16.20
16.00 SQ
15.80
0.75
0.60
0.45
1.60
MAX
61
80
1
60
PIN 1
14.20
14.00 SQ
13.80
TOP VIEW
(PINS DOWN)
1.45
1.40
1.35
0.20
0.09
7°
3.5°
0°
0.10
COPLANARITY
20
41
0.15
0.05
40
21
SEATING
PLANE
VIEW A
0.65
0.38
0.32
0.22
BSC
LEAD PITCH
VIEW A
ROTATED 90° CCW
COMPLIANT TO JEDEC STANDARDS MS-026-BEC
Figure 35. 80-Lead Low Profile Quad Flat Package [LQFP]
(ST-80-2)
Dimensions shown in millimeters
ORDERING GUIDE
Model
ADAV4622BSTZ1
EVAL-ADAV4622EBZ1
Temperature Range SIF Standard
−40°C to +85°C PAL/NTSC/SECAM
Package Description
Package Option
80-Lead Low Profile Quad Flat Package (LQFP)
Evaluation Board
ST-80-2
1 Z = RoHS Compliant Part.
In addition, it is backward compatible with conventional SnPb soldering processes. This means the electroplated Sn coating can be soldered with Sn/Pb solder pastes
at conventional reflow temperatures of 220°C to 235°C.
Purchase of licensed I2C components of Analog Devices or one of its sublicensed Associated Companies conveys a license for the purchaser under the Philips I2C Patent
Rights to use these components in an I2C system, provided that the system conforms to the I2C Standard Specification as defined by Philips.
©2008–2009 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D07068-0-7/09(B)
Rev. B | Page 28 of 28
相关型号：
ADAV803AST-REEL
Audio Codec for Recordable DVD; Package: LQFP 1.4 MM; No of Pins: 64; Temperature Range: Commercial
ADI
ADAV803AST-REEL7
Audio Codec for Recordable DVD; Package: LQFP 1.4 MM; No of Pins: 64; Temperature Range: Commercial
ADI
©2020 ICPDF网 联系我们和版权申明