ADF7901BRUZ-RL7 [ADI]
TELECOM, CELLULAR, RF AND BASEBAND CIRCUIT, PDSO24, LEAD FREE, MO-153AD, TSSOP-24;型号: | ADF7901BRUZ-RL7 |
厂家: | ADI |
描述: | TELECOM, CELLULAR, RF AND BASEBAND CIRCUIT, PDSO24, LEAD FREE, MO-153AD, TSSOP-24 蜂窝 电信 光电二极管 电信集成电路 |
文件: | 总13页 (文件大小:192K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
High Performance ISM Band
OOK/FSK Transmitter IC
ADF7901
FEATURES
GENERAL DESCRIPTION
Single-chip, low power UHF transmitter
369.5 MHz to 395.9 MHz frequency operation using
fractional-N PLL and fully integrated VCO
The ADF7901 is a low power OOK/FSK UHF transmitter
designed for use in RF remote control devices. It is capable of
frequency shift keying (FSK) modulation on eight different
channels, selectable by three external control lines. OOK
modulation is performed by modulating the PA control line.
3.0 V supply voltage
Data rates up to 50 kbps supported
Low current consumption
26 mA at 12 dBm output at 384 MHz
Power-down mode (<1 μA)
24-lead TSSOP
The on-chip VCO operates at 2× the output frequency. The
division by 2 at the output of the VCO reduces the amount of
PA feedthrough. As a result, OOK modulation depths of greater
than 50 dB are easily achievable.
The FSK_ADJ and ASK_ADJ resistors can be adjusted in the
system to optimize output power for each modulation scheme.
An additional 1.5 dB of output power is provided for the lower
bank of channels to adjust for antenna performance. The CE
line allows the transmitter to be powered down completely.
In this mode, the leakage current is typically 0.1 μA.
FUNCTIONAL BLOCK DIAGRAM
C
REG2
PA_EN
C
VCO
OSC1
OSC2
V
DD
VCO
RF
OUT
PA
DV
DD
R = 1
RF
GND
PDF
CHARGE
PUMP
C
REG1
LDO
REGULATOR
1
⎟ FRACTIONAL N
LDO
REGULATOR
2
C
REG2
TXDATA
Σ-Δ
FSK
CHANNEL SELECT
R
SET
OOK_SEL
CE
D
FSK1 FSK2 FSK3
GND
RSET_FSK
RSET_OOK
Figure 1.
Rev. A
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
©2006 Analog Devices, Inc. All rights reserved.
ADF7901* PRODUCT PAGE QUICK LINKS
Last Content Update: 02/23/2017
COMPARABLE PARTS
View a parametric search of comparable parts.
DESIGN RESOURCES
• ADF7901 Material Declaration
• PCN-PDN Information
EVALUATION KITS
• ADF7901 Evaluation Board
• Quality And Reliability
• Symbols and Footprints
DOCUMENTATION
Data Sheet
DISCUSSIONS
View all ADF7901 EngineerZone Discussions.
• ADF7901: High Performance ISM Band 00K/FSK
Transmitter IC Data Sheet
SAMPLE AND BUY
Visit the product page to see pricing options.
SOFTWARE AND SYSTEMS REQUIREMENTS
• ADF70xx Evaluation Software
TECHNICAL SUPPORT
Submit a technical question or find your regional support
number.
• ADIismLINK Development Platform
TOOLS AND SIMULATIONS
DOCUMENT FEEDBACK
• ADIsimSRD Design Studio
Submit feedback for this data sheet.
REFERENCE MATERIALS
Technical Articles
• Low Power, Low Cost, Wireless ECG Holter Monitor
• RF Meets Power Lines: Designing Intelligent Smart Grid
Systems that Promote Energy Efficiency
• Smart Metering Technology Promotes Energy Efficiency
for a Greener World
• The Use of Short Range Wireless in a Multi-Metering
System
• Understand Wireless Short-Range Devices for Global
License-Free Systems
• Wireless Short Range Devices and Narrowband
Communications
This page is dynamically generated by Analog Devices, Inc., and inserted into this data sheet. A dynamic change to the content on this page will not
trigger a change to either the revision number or the content of the product data sheet. This dynamic page may be frequently modified.
ADF7901
TABLE OF CONTENTS
Features .............................................................................................. 1
General Description......................................................................... 1
Functional Block Diagram .............................................................. 1
Specifications..................................................................................... 3
Absolute Maximum Ratings............................................................ 5
ESD Caution.................................................................................. 5
Pin Configuration and Function Descriptions............................. 6
Typical Performance Characteristics ............................................. 8
Circuit Description........................................................................... 9
Loop Filter ..................................................................................... 9
Channel Frequencies.....................................................................9
Layout Guidelines....................................................................... 10
Decoupling.............................................................................. 10
Regulator Stability.................................................................. 10
Grounding............................................................................... 10
Supply ...................................................................................... 10
Digital Lines............................................................................ 10
Outline Dimensions....................................................................... 11
Ordering Guide .......................................................................... 11
REVISION HISTORY
3/06—Rev. 0 to Rev. A
Added Crystal ESR Parameter........................................................ 4
Change to Figure 8 ......................................................................... 10
Updated Outline Dimensions....................................................... 11
Changes to Ordering Guide .......................................................... 11
3/05—Revision 0: Initial Version
Rev. A | Page 2 of 12
ADF7901
SPECIFICATIONS
VDD =3.0 V; GND = 0 V; TA = TMIN to TMAX, unless otherwise noted. Typical specifications, TA = 25°C.1
Table 1.
Parameter
Min
Typ
Max
Unit
Comments/Conditions
RF CHARACTERISTICS
Output Frequency Ranges
Channel 1
369.5
371.1
375.3
376.9
384.0
388.3
391.5
394.3
395.9
9.8304
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
Channel 2
Channel 3
Channel 4
Channel 5
Channel 6
Channel 7
Channel 8
Channel 9
Phase Frequency Detector Frequency
TRANSMISSION PARAMETERS
Transmit Rate
FSK
50
50
kbps
kbps
OOK
Frequency Shift Keying
FSK Separation2
−34.8
+34.8
kHz
kHz
Data = 1
Data = 0
On/Off Keying
Modulation Depth3
83
dB
Output power = 12 dBm
Output Power
Min/Max Range4
fOUT ≤ 384 MHz
fOUT > 384 MHz
15
12
10.5
dBm
dBm
dBm
10
7
Occupied 20 dB BW
OOK at 1 kbps
FSK (PA Off/On) at10 Hz5
28
26
461.9
461.9
kHz
kHz
LOGIC INPUTS
VINH, Input High Voltage
VINL, Input Low Voltage
IINH/IINL, Input Current
CIN, Input Capacitance
POWER SUPPLIES
2.124
V
V
μA
pF
0.2 × VDD
1
10
Voltage Supply
DVDD
3.0
V
Transmit Current Consumption
369.5 MHz to 376.9 MHz at 12 dBm
384 MHz at +12 dBm
388.3 MHz to 395.9 MHz at 10.5 dBm
384 MHz at 5 dBm
26
26
21
17
mA
mA
mA
mA
Power-Down Mode
Low Power Sleep Mode6
0.2
1
μA
Rev. A| Page 3 of 12
ADF7901
Parameter
Min
Typ
Max
Unit
Comments/Conditions
PHASE-LOCKED LOOP
VCO Gain
Spurious3, 7
30
MHz/V
At 384 MHz
100 kHz loop BW
Integer Boundary
Reference
Harmonics3
–45
−70
−23
−23
dBc
dBc
Second Harmonic VDD = 3.0 V
Third Harmonic VDD = 3.0 V
All Other Harmonics
REFERENCE INPUT
Crystal Reference
−24
−14
−21
−11
−18
dBc
dBc
dBc
9.8304
MHz
Ω
Crystal ESR8
80
POWER AMPLIFIER
PA Output Impedance
TIMING INFORMATION
Crystal Oscillator to PLL Lock3
PA Enable to PA Ready–PLL Settle9
TEMPERATURE RANGE (TA)
97 Ω + 6.4 pF
At 384 MHz
2
100
3
250
50
ms
μs
°C
0
1 Operating temperature range is 0°C to 50°C.
2 Frequency Deviation = 58 × (9.8304 MHz)/214. Error in the crystal is reflected in variation in the desired deviation.
3 Not production tested; based on characterization.
4 The output power can be varied in both ASK/FSK mode by altering the relevant external resistor.
5 Measured using spectrum analyzer, 1 MHz span, 100 kHz RBW, maximum hold enabled.
6 Maximum power-down current specification applies for the OSC2 pin grounded.
7 Measured >461.9 kHz away from channel.
8 Maximum recommended crystal ESR. The crystal oscillator works with crystals with higher ESR, but this results in longer power-up times.
9 This specification refers to the time taken for the PLL to regain lock after the PA has been enabled. The PA is should only be enabled after the PLL has settled to the
correct frequency.
Rev. A | Page 4 of 12
ADF7901
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.1
Table 2.
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those listed in the operational sections
of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Parameter
Value
VDD to GND2
−0.3 V to +4.0 V
−0.3 V to +4.0 V
−0.3 V to VDD + 0.3 V
RFVDD to GND
Digital I/O Voltage to GND
Operating Temperature Range
Industrial (B Version)
Storage Temperature Range
Maximum Junction Temperature
TSSOP θJA Thermal Impedance
Lead Temperature, Soldering
Vapor Phase (60 sec)
0°C to 50°C
−65°C to +125°C
125°C
150.4°C/W
235°C
240°C
Infrared (15 sec)
1 This device is a high performance, RF-integrated circuit with an ESD rating
of <1 kV. It is ESD sensitive. Take proper precautions for handling and
assembly.
2 GND = RFGND = DGND = 0 V.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the
human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. A| Page 5 of 12
ADF7901
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
C
DV
DD
1
24
REG2
C
2
23
R
REG1
SET
CP
3
22 PA_EN
OUT
DV
4
21
20
19
18
17
16
15
14
13
TxDATA
DD
D
5
GND
RF
RF
OUT
ADF7901
NC
6
GND
TOP VIEW
(Not to Scale)
D
7
GND
VCO
IN
OSC1
OSC2
8
C
VCO
9
RSET_FSK
10
OOK_SEL
RSET_OOK
CE
FSK1 11
12
FSK3
FSK2
Figure 2. Pin Configuration
Table 3. Pin Function Descriptions
Pin No. Mnemonic Function
1
2
3
DVDD
CREG1
CPOUT
Positive Supply for the Digital Circuitry. This must be 3.0 V. Decoupling capacitors to the analog ground plane
should be placed as close as possible to this pin.
A 2.2 μF capacitor should be added at CREG1 to reduce regulator noise and improve stability. A reduced capacitor
improves regulator power-on time but can cause higher spurious.
Charge Pump Output. This output generates current pulses that are integrated in the loop filter. The integrated
current changes the control voltage on the input to the VCO.
4
5
6
7
8
TxDATA
DGND
NC
DGND
OSC1
Digital FSK data to be transmitted is inputted on this pin.
Ground for Digital Section.
No Connect.
Ground for Digital Section.
The reference crystal should be connected between this pin and the OSC2 pin. The necessary crystal load
capacitor should be tied between this pin and ground.
9
OSC2
The reference crystal should be connected between this pin and the OSC1 pin. The necessary crystal load
capacitor should be tied between this pin and ground.
A TCXO or external square wave can also be connected to this pin, with OSC1 left floating. A DC-blocking
capacitor (4.7 nF is adequate) should be placed between the TCXO output and OSC2 pin.
When not using an external regulator, a 1 MΩ resistor can be tied between the OSC2 pin and ground to meet the
power-down current specification of 1 μA.
10
11
12
13
14
15
OOK_SEL
FSK1
FSK2
FSK3
CE
A high on this pin selects operation in OOK mode at 384 MHz when CE is high.
FSK Channel Select Pin. This represents the LSB of the channel select pins.
FSK Channel Select Pin.
FSK Channel Select Pin.
Bringing CE low puts the ADF7901 into power-down, drawing <1 μA of current.
The value of this resistor sets the output power for data = 1 in OOK mode. A resistor of 3.6 kΩ provides the
maximum output power. Increasing the resistor reduces the power and the current consumption. A lower resistor
value than 3.6 kΩ can be used to increase the power to a maximum of 14 dBm. The PA does not operate efficiently
in this mode.
RSET_OOK
16
RSET_FSK
The value of this resistor sets the output power in FSK mode. A resistor of 3.6 kΩ provides maximum output
power. Increasing the resistor reduces the power and the current consumption. A resistor value lower than 3.6 kΩ
can be used to increase the power to a maximum of 14 dBm. The PA does not operate efficiently in this mode.
17
18
CVCO
A 22 nF capacitor should be tied between the CVCO and CREG2 pins. This line should run underneath the ADF7901.
The capacitor is necessary to ensure stable VCO operation.
The tuning voltage on this pin determines the output frequency of the voltage controlled oscillator (VCO).
The higher the tuning voltage the higher the output frequency. The output of the loop filter is connected here.
VCOIN
19
20
RFGND
RFOUT
Ground for Output Stage of Transmitter.
The modulated signal is available at this pin. Output power levels are from –5 dBm to +12 dBm. The output
should be impedance matched using suitable components to the desired load.
Rev. A | Page 6 of 12
ADF7901
Pin No. Mnemonic
Function
21
DVDD
Voltage Supply for VCO and PA Section. It should be supplied with 3.0 V. Decoupling capacitors to the ground
plane should be placed as close as possible to this pin.
22
PA_EN
This pin is used to enable the power amplifier. It should be modulated with the OOK data in OOK mode. In
FSK mode, it should be enabled when the PLL is locked.
23
24
RSET
CREG2
External Resistor. Sets charge pump current and some internal bias currents. Use 3.6 kΩ as default.
A 2.2 μF capacitor should be added at CREG2 to reduce regulator noise and improve stability. A reduced capacitor
improves regulator power-on time but can cause higher spurs.
Rev. A| Page 7 of 12
ADF7901
TYPICAL PERFORMANCE CHARACTERISTICS
Mkr1 10.00kHz
Noise –89.55dB/Hz
Ref 15dBm
Avg
Atten 30dB
16
Log
1R
10
dB/
12
8
RBW
300.0000000Hz
PAvg
1
W1 S2
S3 FS
AA
4
£(f):
f<50k
Swp
0
2
3
4
5
6
7
8
9
10
Center 395.948 29MHz
#Res BW 300Hz
Span 50kHz
Sweep 2.118 s (601 pts)
VBW 300Hz
RSET
Figure 5. Phase Noise at Channel 9
Figure 3. Output Power vs. RSET FSK, Upper FSK Channels,
Measured into 50 Ω
Mkr4 1.59GHz
–21.30dB
Ref 15dBm
Peak
Atten 30dB
35
Log
10
dB/
4R
Marker Trace Type X Axis
Amplitude
Freq 400MHz –25.56dB
Freq 800MHz –13.89dB
Freq 1.19GHz –34.53dB
Freq 1.59GHz –21.30dB
2
1
2
3
4
(1)
(1)
(1)
(1)
4
30
1
3
25
20
15
10
LgAv
Center 5.50GHz
#Res BW 1MHz
4
5
6
7
8
9
10
Span 10.5GHz
Sweep 17.52 ms (601 pts)
VBW 1MHz
OUTPUT POWER (dBm)
Figure 4. Current Consumption vs. Output Power, Upper FSK Channels,
Measured into 50 Ω
Figure 6. Harmonic Levels—Up to Fourth Harmonic,
Measured at Channel 9 into 50 Ω
Rev. A | Page 8 of 12
ADF7901
CIRCUIT DESCRIPTION
Table 4.
CHANNEL FREQUENCIES
Frequency (MHz)
FSK3
FSK2
FSK1
OOK_SEL
The nine channel frequencies listed in Table 4 are obtainable
from a single 9.8304 MHz crystal reference by changing the
value of the N and F numbers in the fractional PLL, using
control lines FSK1, FSK2, and FSK3. The channel frequency is
given by
369.5
371.1
375.3
376.9
0
0
0
0
0
0
1
1
0
1
0
0
0
0
0
0
1
384.0
Don’t
care
1
1
1
1
Don’t
care
0
0
1
1
Don’t
care
0
1
0
1
FCHANNEL = FREF × (N + F)
388.3
391.5
394.3
395.9
0
0
0
0
However, the VCO is tuned to operate over a frequency range
of 344 MHz to 401 MHz (typically). Therefore, any channel
frequency within this range can be obtained if the required
reference frequency is used. The N and F numbers for each
channel are listed in Table 5, together with the corresponding
channel frequencies for 9.8304 MHz and, for example purposes,
frequencies for 10 MHz. With the 10 MHz reference, the two
largest N settings give channel frequencies above the maximum
VCO output frequency and are therefore invalid.
LOOP FILTER
The loop filter integrates the current pulses from the charge
pump to form a voltage that tunes the output of the VCO to the
desired frequency. It also attenuates spurious levels generated by
the PLL. The recommended loop filter design for this circuit is
297 kHz. This is based on the trade-off between attenuation of
beat note spurs and the need to minimize chirp when the PA is
turned on.
Frequency deviation is also dependent on reference frequency.
The relationship is given by
FDEV = 58 × (9.8304 MHz)/214
Therefore, the frequency deviation is 34.8 kHz when the
9.8304 MHz reference is used and 35.4 kHz when the 10 MHz
reference is used.
R2 = 6.2k
Ω
CHARGE
PUMP OUT
VCO
R1 = 3k
Ω
C1 = 33pF
C2 = 390pF
C3 = 10pF
Table 5.
Channel Frequency (MHz)
N
F
9.8304 MHz Ref 10 MHz Ref
Figure 7.
37
37
38
38
39
39
39
40
40
2406/4096
3073/4096
727/4096
1374/4096
256/4096
2048/4096
3381/4096
452/4096
1118/4096
369.5
371.1
375.3
376.9
384.0
388.3
391.5
394.3
395.9
375.9
377.5
381.8
383.4
390.6
395
398.3
N/A
N/A
Improved spurious performance in FSK mode can be achieved
by using a narrower loop bandwidth. For a data rate of 20 kbps,
a loop bandwidth of roughly 50 kHz would be suitable. The
following components give a loop bandwidth of 51.1 kHz:
C1 = 680 pF
C2 = 15 nF
C3 = 180 pF
R1 = 510 Ω
R2 = 6.2 kΩ
ADIsimPLL is a free software tool offered by Analog Devices
for assistance in designing with ADI’s frequency synthesizers
and ISM band transmitters. To select the correct loop filter
components for use with the ADF7901, open a project for the
ADF7012 device. Then, enter the desired output carrier
frequency and loop bandwidth, and use the 870 μA charge
pump current setting.
ADIsimPLL can be downloaded from www.analog.com.
Rev. A| Page 9 of 12
ADF7901
2.2μF
2.2μF
22nF
MATCHING RF
TO 50Ω
OUT
DV
C
C
C
DD
REG1
VCO REG2
R
SET
27nH
5.6pF
5TH-ORDER, LOW-PASS FILTER
3.6kΩ
1.5pF
22nH
22nH
RF
OUT
ANTENNA
36nH
3pF
8pF
3pF
VCO
CP
OUT
IN
VCO
IN
ADF7901
MATCHING 50Ω
TO ANTENNA
RSET_FSK
RSET_OOK
3.6kΩ
3.6kΩ
TxDATA
FSK1
FSK2
OSC2
OSC1
FSK3
9.8304MHz
OOK_SEL
PA_EN
CE
33pF 33pF
GND
NOTES
1. DECOUPLING CAPACITORS HAVE
BEEN OMITTED FOR CLARITY.
Figure 8. Applications Diagram for the ADF7901 in a Remote Control System
Grounding
LAYOUT GUIDELINES
Emphasis should be placed on grounding once the decoupling
capacitors have been added. The PA stage switches currents of
15 mA in maximum power mode. This causes changes in the
ground resulting in large return currents that can radiate to
other parts of the board. The shortest and least obstructed
ground from RFGND back to the ground of the battery should be
ensured. A 4-layer board helps, as well as flooding the top layer.
The ground paths should not have any vias and should be wide
tracks.
The layout of the board is crucial to ensuring low levels of
spurious and harmonics.
Decoupling
Decoupling capacitors (high frequency 22 pF, low frequency
100 nF) should be placed as close as possible to the supply pins
on the part. Low size 0402 and 0603 components are recom-
mended for the high frequency rejection on the supply.
Regulator Stability
Supply
A minimum of 1 μF is needed on both CREG1 and CREG2 to ensure
stability. An additional 22 pF capacitor can be added to reject
higher frequency noise. Because many of the internal blocks
run off the regulator, it is critical to reduce its noise. Low size
0402 and 0603 components are recommended for the high
frequency rejection on the supply.
The supply tracks can be routed through vias, because they act
as free inductors and make layout easier on a 2-layer board
(see the Decoupling section). Tracks should be wide.
Digital Lines
Digital lines should contain a large resistor in series. This
impedance blocks signals of many frequencies, including
harmonics and the carrier frequency. Long control lines can
act as antennae. It can be useful to add capacitance to ground.
There is some capacitance to ground provided by the lines and
at the input of the digital pins.
Rev. A | Page 10 of 12
ADF7901
OUTLINE DIMENSIONS
7.90
7.80
7.70
24
13
12
4.50
4.40
4.30
6.40 BSC
1
PIN 1
0.65
BSC
1.20
MAX
0.15
0.05
0.75
0.60
0.45
8°
0°
0.30
0.19
0.20
0.09
SEATING
PLANE
0.10 COPLANARITY
COMPLIANT TO JEDEC STANDARDS MO-153AD
Figure 9. 24-Lead Thin Shrink Small Outline Package [TSSOP]
(RU-24)
Dimensions shown in millimeters
ORDERING GUIDE
Model
ADF7901BRU
ADF7901BRU-REEL
ADF7901BRU-REEL7
ADF7901BRUZ1
ADF7901BRUZ-RL1
ADF7901BRUZ-RL71
EVAL-ADF7901EB
Temperature Range
Package Description
Package Option
RU-24
RU-24
RU-24
RU-24
0°C to 50°C
0°C to 50°C
0°C to 50°C
0°C to 50°C
0°C to 50°C
0°C to 50°C
24-Lead Thin Shrink Small Outline Package (TSSOP)
24-Lead Thin Shrink Small Outline Package (TSSOP)
24-Lead Thin Shrink Small Outline Package (TSSOP)
24-Lead Thin Shrink Small Outline Package (TSSOP)
24-Lead Thin Shrink Small Outline Package (TSSOP)
24-Lead Thin Shrink Small Outline Package (TSSOP)
Evaluation Board
RU-24
RU-24
1 Z = Pb-free part.
Rev. A| Page 11 of 12
ADF7901
NOTES
©2006 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D05349-0-3/06(A)
Rev. A | Page 12 of 12
相关型号:
©2020 ICPDF网 联系我们和版权申明