ADG701BRTZ-REEL2 [ADI]
IC 1-CHANNEL, SGL POLE SGL THROW SWITCH, PDSO6, PLASTIC, MO-178AB, SOT-23, 6 PIN, Multiplexer or Switch;
| 型号： | ADG701BRTZ-REEL2 |
| 厂家： | 
ADI |
| 描述： | IC 1-CHANNEL, SGL POLE SGL THROW SWITCH, PDSO6, PLASTIC, MO-178AB, SOT-23, 6 PIN, Multiplexer or Switch 光电二极管 |
| 文件： | 总12页 (文件大小：358K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
CMOS Low Voltage
2 Ω SPST Switches
ADG701/ADG702
FUNCTIONAL BLOCK DIAGRAM
FEATURES
1.8 V to 5.5 V single supply
2 Ω (typ) on resistance
Low on-resistance flatness
–3 dB bandwidth > 200 MHz
Rail-to-rail operation
Fast switching times:
tON 18 ns
ADG701
ADG702
S
D
S
D
IN
IN
SWITCHES SHOWN FOR A LOGIC 1 INPUT
tOFF 12 ns
Figure 1.
Typical power consumption < 0.01 µW
TTL/CMOS compatible
PRODUCT HIGHLIGHTS
1. 1.8 V to 5.5 V single-supply operation. The ADG701/
ADG702 offer high performance, including low on
resistance and fast switching times, and are fully specified
and guaranteed with 3 V and 5 V supply rails.
APPLICATIONS
Battery powered systems
Communication systems
Sample hold systems
Audio signal routing
Video switching
Mechanical reed relay replacement
2. Very low RON (3 Ω max at 5 V, 5 Ω max at 3 V). At 1.8 V
operation, RON is typically 40 Ω over the temperature range.
3. On resistance flatness RFLAT(ON) (1 Ω max).
4. −3 dB bandwidth > 200 MHz.
GENERAL DESCRIPTION
The ADG701/ADG702 are monolithic CMOS SPST switches.
These switches are designed on an advanced submicron process
that provides low power dissipation yet high switching speed,
low on resistance, and low leakage currents. In addition, −3 dB
bandwidths of greater than 200 MHz can be achieved.
5. Low power dissipation. CMOS construction ensures low
power dissipation.
6. Fast tON/tOFF.
7. Tiny 5-lead SOT-23, 6-lead SOT-23, and 8-lead MSOP
packages.
The ADG701/ADG702 can operate from a single 1.8 V to 5.5 V
supply, making it ideal for use in battery-powered instruments
and with the new generation of DACs and ADCs from Analog
Devices.
Figure 1 shows that with a logic input of 1, the switch of the
ADG701 is closed, while that of the ADG702 is open. Each
switch conducts equally well in both directions when on.
The ADG701/ADG702 are available in 5-lead SOT-23, 6-lead
SOT-23, and 8-lead MSOP packages.
Rev. B
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.326.8703
www.analog.com
© 2004 Analog Devices, Inc. All rights reserved.
ADG701/ADG702
TABLE OF CONTENTS
Specifications..................................................................................... 3
Absolute Maximum Ratings............................................................ 5
ESD Caution.................................................................................. 5
Pin Configurations and Function Descriptions ........................... 6
Typical Performance Characteristics ............................................. 7
Test Circuits ....................................................................................... 8
Applications Information.................................................................9
ADG701/ADG702 Supply Voltages............................................9
On Response vs. Frequency .........................................................9
Off Isolation...................................................................................9
Outline Dimensions....................................................................... 10
Ordering Guide .......................................................................... 11
REVISION HISTORY
6/04—Data Sheet Changed from Rev. A to Rev. B
Updated Format.................................................................. Universal
Added 5-Lead SOT-23 Package ........................................ Universal
Updated Outline Dimensions........................................................10
Changes to Ordering Guide ...........................................................11
8/98—Data Sheet Changed from Rev. 0 to Rev. A
Rev. B | Page 2 of 12
ADG701/ADG702
SPECIFICATIONS
VDD = 5 V 10ꢀ, GND = 0 V. Temperature range for B version is −40°C to +85°C, unless otherwise noted.
Table 1.
B Version
Parameter
+25°C
–40°C to +85°C
Unit
Test Conditions/Comments
ANALOG SWITCH
Analog Signal Range
On Resistance (RON)
0 V to VDD
V
2
3
0.5
Ω typ
Ω max
Ω typ
Ω max
VS = 0 V to VDD, IS = –10 mA; Figure 11
VS = 0 V to VDD, IS = –10 mA
4
On-Resistance Flatness (RFLAT(ON)
)
1.0
LEAKAGE CURRENTS
VDD = 5.5 V
Source OFF Leakage, IS (OFF)
0.01
0.25
0.01
0.25
0.01
0.25
nA typ
nA max
nA typ
nA max
nA typ
nA max
VS = 4.5 V/1 V, VD = 1 V/4.5 V; Figure 12
0.35
0.35
0.35
Drain OFF Leakage, ID (OFF)
VS = 4.5 V/1 V, VD = 1 V/4.5 V; Figure 12
VS = VD = 1 V, or 4.5 V; Figure 13
Channel ON Leakage, ID, IS (ON)
DIGITAL INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current
2.4
0.8
V min
V max
IINL or IINH
0.005
µA typ
VIN = VINL or VINH
0.1
µA max
DYNAMIC CHARACTERISTICS1
tON
12
8
ns typ
ns max
ns typ
ns max
pC typ
dB typ
dB typ
MHz typ
pF typ
pF typ
pF typ
RL = 300 Ω , CL = 35 pF
VS = 3 V; Figure 14
RL = 300 Ω , CL = 35 pF
VS = 3 V; Figure 14
VS = 2 V, RS = 0 Ω , CL = 1 nF; Figure 15
RL = 50 Ω , CL = 5 pF, f = 10 MHz
RL = 50 Ω , CL = 5 pF, f = 1 MHz; Figure 16
RL = 50 Ω , CL = 5 pF; Figure 17
18
12
tOFF
Charge Injection
Off Isolation
5
–55
–75
200
17
17
38
Bandwidth –3 dB
CS (OFF)
CD (OFF)
CD, CS (ON)
POWER REQUIREMENTS
VDD = 5.5 V
Digital inputs = 0 V or 5 V
IDD
0.001
µA typ
1.0
µA max
1 Guaranteed by design, not subject to production test.
Rev. B | Page 3 of 12
ADG701/ADG702
VDD = 3 V 10ꢀ, GND = 0 V. Temperature range for B version is −40°C to +85°C, unless otherwise noted.
Table 2.
B Version
Parameter
+25°C
−40°C to +85°C
Unit
Test Conditions/Comments
ANALOG SWITCH
Analog Signal Range
On Resistance (RON)
0 V to VDD
6
V
3.5
5
1.5
Ω typ
Ω max
Ω typ
VS = 0 V to VDD, IS = −10 mA; Figure 11
On-Resistance Flatness (RFLAT(ON)
)
VS = 0 V to VDD, IS = −10 mA
VDD = 3.3 V
LEAKAGE CURRENTS
Source OFF Leakage IS(OFF)
0.01
0.25
0.01
0.25
0.01
0.25
nA typ
nA max
nA typ
nA max
nA typ
nA max
VS = 3 V/1 V, VD = 1 V/3 V; Figure 12
0.35
0.35
0.35
Drain OFF Leakage ID(OFF)
VS = 3 V/1 V, VD = 1 V/3 V; Figure 12
V = VD = 1 V, or 3 V; Figure 13
Channel ON Leakage ID, IS(ON)
DIGITAL INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current
2.0
0.4
V min
V max
IINL or IINH
0.005
µA typ
VIN = VINL or VINH
0.1
µA max
DYNAMIC CHARACTERISTICS1
tON
14
8
ns typ
ns max
ns typ
ns max
pC typ
RL = 300 Ω , CL = 35 pF
VS = 2 V, Figure 14
RL = 300 Ω , CL = 35 pF
VS = 2 V, Figure 14
20
13
tOFF
Charge Injection
Off Isolation
4
VS = 1.5 V, RS = 0 Ω , CL = 1 nF; Figure 15
−55
−75
dB typ
dB typ
RL = 50 Ω , CL = 5 pF, f = 10 MHz
RL = 50 Ω , CL = 5 pF, f = 1 MHz; Figure 16
Bandwidth −3 dB
200
MHz typ
RL = 50 Ω , CL = 5 pF; Figure 17
CS (OFF)
CD (OFF)
CD, CS (ON)
17
17
38
pF typ
pF typ
pF typ
POWER REQUIREMENTS
VDD = 3.3 V
Digital Inputs = 0 V or 3 V
IDD
0.001
µA typ
1.0
µA max
1 Guaranteed by design, not subject to production test.
Rev. B | Page 4 of 12
ADG701/ADG702
ABSOLUTE MAXIMUM RATINGS
TA = +25°C, unless otherwise noted.
Table 3.
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those listed in the operational sections
of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability. Only one absolute maximum rating may be
applied at any one time.
Parameter
Rating
VDD to GND
Analog, Digital Inputs1
−0.3 V to +7 V
−0.3 V to VDD +0.3 V
or 30 mA, whichever
occurs first
Continuous Current, S or D
Peak Current, S or D
30 mA
100 mA, pulsed at 1 ms,
10% duty cycle max
Operating Temperature Range
Industrial (B Version)
Table 4. Truth Table
−40°C to +85°C
−65°C to +150°C
150°C
315 mW
206°C/W
44°C/W
282 mW
229.6°C/W
91.99°C/W
ADG701 In
ADG702 In
Switch Condition
Storage Temperature Range
Junction Temperature
MSOP Package, Power Dissipation
θJA Thermal Impedance
θJC Thermal Impedance
SOT-23 Package, Power Dissipation
θJA Thermal Impedance
θJC Thermal Impedance
Lead Temperature, Soldering
Vapor Phase (60 sec)
0
1
1
0
OFF
ON
215°C
220°C
2 kV
Infrared (15 sec)
ESD
1 Overvoltages at IN, S, or D are clamped by internal diodes. Current should be
limited to the maximum ratings given.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. B | Page 5 of 5
ADG701/ADG702
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
D
NC
NC
1
2
3
4
8
7
6
5
S
D
S
1
2
3
6
V
DD
D
S
1
2
3
5
4
V
DD
ADG701/
ADG702
ADG701/
ADG702
ADG701/
ADG702
TOP VIEW
(Not to Scale)
GND
IN
5
4
NC
IN
TOP VIEW
TOP VIEW
GND
IN
GND
(Not to Scale)
(Not to Scale)
V
NC
DD
NC = NO CONNECT
NC = NO CONNECT
Figure 2. 8-Lead MSOP
Figure 3. 6-Lead SOT-23
Figure 4. 5-Lead SOT-23
Table 5. Pin Descriptions
Term
VDD
GND
S
D
IN
Description
Most positive power supply potential.
Ground (0 V) Reference.
Source Terminal. May be an input or output.
Drain Terminal. May be an input or output.
Logic Control Input.
RON
Ohmic resistance between D and S.
RFLAT(ON)
Flatness is defined as the difference between the maximum and minimum value of on resistance as measured
over the specified analog signal range.
IS (OFF)
Source Leakage Current with the Switch OFF.
ID (OFF)
Drain Leakage Current with the Switch OFF.
ID, IS (ON)
VD (VS)
Channel Leakage Current with the Switch ON.
Analog Voltage on Terminals D and S.
CS (OFF)
OFF Switch Source Capacitance.
CD (OFF)
CD, CS (ON)
tON
OFF Switch Drain Capacitance.
ON Switch Capacitance.
Delay between applying the digital control input and the output switching on. See Figure 14.
Delay between applying the digital control input and the output switching off.
A measure of unwanted signal coupling through an OFF switch.
A measure of the glitch impulse transferred from the digital input to the analog output during switching.
The frequency at which the output is attenuated by −3 dBs.
The frequency response of the ON switch.
tOFF
Off Isolation
Charge Injection
Bandwidth
On Response
On Loss
The voltage drop across the ON switch seen in Figure 10 as the number of dBs the signal is from 0 dB at very low
frequencies.
Rev. B | Page 6 of 12
ADG701/ADG702
TYPICAL PERFORMANCE CHARACTERISTICS
3.5
10m
1m
V
= 5V
DD
V
= 2.7V
T
= 25°C
DD
A
3.0
2.5
2.0
1.5
1.0
0.5
0
100µ
10µ
1µ
V
= 4.5V
V
= 3.0V
DD
DD
V
= 5.0V
DD
100n
10n
1n
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
10
100
1k
10k
100k
1M
10M
V
OR V – DRAIN OR SOURCE VOLTAGE (V)
FREQUENCY (Hz)
D
S
Figure 8. Supply Current vs. Input Switching Frequency
Figure 5. On Resistance as a Function of VD (VS) Single Supplies
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
3.5
V
= 5V, 3V
DD
V
= 3V
DD
3.0
2.5
2.0
1.5
1.0
0.5
0
+85°C
+25°C
–40°C
10k
100k
1M
10M
100M
0
0.5
1.0
1.5
2.0
2.5
3.0
FREQUENCY (Hz)
V
OR V – DRAIN OR SOURCE VOLTAGE (V)
D
S
Figure 9. Off Isolation vs. Frequency
Figure 6. On Resistance as a Function of VD (VS) for Different Temperatures
DD = 3 V
V
0
–2
–4
–6
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
V
= 5V
DD
V
= 3V
DD
+85°C
+25°C
–40°C
10k
100k
1M
10M
100M
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
FREQUENCY (Hz)
V
OR V – DRAIN OR SOURCE VOLTAGE (V)
S
D
Figure 10. On Response vs. Frequency
Figure 7. On Resistance as a Function of VD (VS) for Different Temperatures
DD = 5 V
V
Rev. B | Page 7 of 12
ADG701/ADG702
TEST CIRCUITS
I
DS
V1
I
(ON)
A
I
(OFF)
A
I
(OFF)
A
D
S
D
S
D
S
D
S
D
V
R
= V1/I
V
S
V
D
V
V
D
S
ON
DS
S
Figure 11. On Resistance
Figure 12. Off Leakage
Figure 13. On Leakage
V
V
DD
0.1µF
V
IN
IN
ADG701
ADG702
50%
50%
50%
50%
DD
V
OUT
S
D
V
R
C
L
L
V
S
300Ω
35pF
IN
90%
90%
V
OUT
GND
tON
tOFF
Figure 14. Switching Times
V
V
DD
DD
V
IN
ADG701
ADG702
ON
OFF
R
S
S
D
V
OUT
C
1nF
L
V
S
V
IN
IN
V
OUT
∆V
OUT
GND
Q
= C × ∆V
INJ
L
OUT
Figure 15. Charge Injection
V
V
V
DD
DD
0.1µF
0.1µF
V
DD
DD
V
V
OUT
OUT
S
D
S
D
R
50Ω
R
L
50Ω
L
IN
IN
V
V
IN
IN
V
V
S
S
GND
GND
Figure 16. Off Isolation
Figure 17. Bandwidth
Rev. B | Page 8 of 12
ADG701/ADG702
APPLICATIONS INFORMATION
The ADG701/ADG702 belong to Analog Devices’ new family
of CMOS switches. This series of general-purpose switches
have improved switching times, lower on resistance, higher
bandwidth, low power consumption, and low leakage currents.
The signal transfer characteristic is dependent on the switch
channel capacitance, CDS. This capacitance creates a frequency
zero in the numerator of the transfer function A(s). Because the
switch on resistance is small, this zero usually occurs at high
frequencies. The bandwidth is a function of the switch output
capacitance combined with CDS and the load capacitance. The
frequency pole corresponding to these capacitances appears in
the denominator of A(s).
ADG701/ADG702 SUPPLY VOLTAGES
Functionality of the ADG701/ADG702 extends from 1.8 V to
5.5 V single supply, making the parts ideal for battery-powered
instruments, where power efficiency and performance are
important design parameters.
The dominant effect of the output capacitance, CD, causes the
pole breakpoint frequency to occur first. In order to maximize
bandwidth, a switch must have a low input and output capaci-
tance and low on resistance. The on response versus frequency
for the ADG701/ADG702 can be seen in Figure 10.
It is important to note that the supply voltage affects the input
signal range, the on resistance, and the switching times of the
part. The effects of the power supplies can be clearly seen in the
Typical Performance Characteristics and the Specifications
sections.
OFF ISOLATION
Off isolation is a measure of the input signal coupled through
an off switch to the switch output. The capacitance, CDS, couples
the input signal to the output load, when the switch is off, as
shown in Figure 19.
For VDD = 1.8 V operation, RON is typically 40 Ω over the
temperature range.
ON RESPONSE VS. FREQUENCY
C
Figure 18 illustrates the parasitic components that affect the ac
performance of CMOS switches (a box surrounds the switch).
Additional external capacitances further degrade some per-
formance. These capacitances affect feedthrough, crosstalk,
and system bandwidth.
DS
S
D
V
OUT
C
R
LOAD
C
LOAD
D
V
IN
Figure 19. Off Isolation Is Affected by External Load Resistance and
Capacitance
C
DS
S
D
V
OUT
The larger the value of CDS, the larger the values of feedthrough
produced. Figure 9 illustrates the drop in off isolation as a
function of frequency. From dc to roughly 1 MHz, the switch
shows better than −75 dB isolation. Up to frequencies of 10
MHz, the off isolation remains better than −55 dB. As the
frequency increases, more and more of the input signal is
coupled through to the output. Off isolation can be maximized
by choosing a switch with the smallest CDS possible. The values
of load resistance and capacitance also affect off isolation, as
they contribute to the coefficients of the poles and zeros in the
transfer function of the switch when open.
R
ON
C
R
LOAD
C
LOAD
D
V
IN
Figure 18. Switch Represented by Equivalent Parasitic Components
The transfer function that describes the equivalent diagram of
the switch (Figure 18) is of the form (A)s shown below.
⎡
⎢
⎣
⎤
⎥
⎦
s(RON
s(RONCT RT ) +1
CDS ) +1
A(s) = RT
Where CT = CLOAD + CD + CDS.
⎡
⎢
⎣
⎤
⎥
⎦
s(RLOAD
s(RLOAD )(CT ) +1
C
DS ) +1
A(s) = RT
Rev. B | Page 9 of 12
ADG701/ADG702
OUTLINE DIMENSIONS
3.00
BSC
8
5
4
4.90
BSC
3.00
BSC
PIN 1
0.65 BSC
1.10 MAX
0.15
0.00
0.80
0.60
0.40
8°
0°
0.38
0.22
0.23
0.08
COPLANARITY
0.10
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-187AA
Figure 20. 8-Lead Mini Small Outline Package [MSOP]
(RM-8)
Dimensions shown in millimeters
2.90 BSC
6
1
5
2
4
3
2.80 BSC
1.60 BSC
PIN 1
INDICATOR
0.95 BSC
1.90
BSC
1.30
1.15
0.90
1.45 MAX
0.22
0.08
10°
4°
0°
0.60
0.45
0.30
0.50
0.30
0.15 MAX
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-178AB
Figure 21. 6-Lead Plastic Surface Mount Package [SOT-23]
(RT-6)
Dimensions shown in inches and (millimeters)
Rev. B | Page 10 of 12
ADG701/ADG702
2.90 BSC
5
4
3
2.80 BSC
1.60 BSC
2
PIN 1
0.95 BSC
1.90
BSC
1.30
1.15
0.90
1.45 MAX
0.22
0.08
10°
5°
0°
0.15 MAX
0.50
0.30
0.60
0.45
0.30
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-178AA
Figure 22. 5-Lead Plastic Surface Mount Package [SOT-23]
(RJ-5)
Dimensions shown in inches and (millimeters)
ORDERING GUIDE
Model
ADG701BRJ-500RL7
ADG701BRJ-REEL
ADG701BRJ-REEL7
ADG701BRM
Temperature Range
Package Descriptions
Package Options
Brand1
S3B
S3B
S3B
S3B
S3B
S3B
S3B
S3B
S3B
S3B
S3B
S4B
S4B
S4B
S4B
S4B
S4B
S4B
S4B
S4B
S4B
S4B
SOT-23 (Plastic Surface Mount)
SOT-23 (Plastic Surface Mount)
SOT-23 (Plastic Surface Mount)
MSOP (Small Outline)
RJ-5
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
RJ-5
RJ-5
RM-8
RM-8
RM-8
RT-6
RT-6
RT-6
RT-6
RT-6
RJ-5
ADG701BRM-REEL
ADG701BRM-REEL7
ADG701BRT
MSOP (Small Outline)
MSOP (Small Outline)
SOT-23 (Plastic Surface Mount)
SOT-23 (Plastic Surface Mount)
SOT-23 (Plastic Surface Mount)
SOT-23 (Plastic Surface Mount)
SOT-23 (Plastic Surface Mount)
SOT-23 (Plastic Surface Mount)
SOT-23 (Plastic Surface Mount)
SOT-23 (Plastic Surface Mount)
MSOP (Small Outline)
ADG701BRT-REEL
ADG701BRT-REEL7
ADG701BRTZ-REEL2
ADG701BRTZ-REEL7
ADG702BRJ-500RL7
ADG702BRJ-REEL
ADG702BRJ-REEL7
ADG702BRM
2
RJ-5
RJ-5
RM-8
RM-8
RM-8
RT-6
RT-6
RT-6
RT-6
RT-6
ADG702BRM-REEL
ADG702BRM-REEL7
ADG702BRT
MSOP (Small Outline)
MSOP (Small Outline)
SOT-23 (Plastic Surface Mount)
SOT-23 (Plastic Surface Mount)
SOT-23 (Plastic Surface Mount)
SOT-23 (Plastic Surface Mount)
SOT-23 (Plastic Surface Mount)
ADG702BRT-REEL
ADG702BRT-REEL7
ADG702BRTZ-REEL
2
ADG702BRTZ-REEL7
2
1 Brand = Due to package size limitations, these three characters represent the part number.
2 Z = Pb-free part.
Rev. B | Page 11 of 12
ADG701/ADG702
NOTES
©
2004 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
C00039–0–6/04(B)
Rev. B | Page 12 of 12
相关型号：
ADG701LBRJZ-500RL7
1-CHANNEL, SGL POLE SGL THROW SWITCH, PDSO5, LEAD FREE, MO-178AA, SOT-23, 5 PIN
ROCHESTER
ADG701LBRJZ-REEL
1-CHANNEL, SGL POLE SGL THROW SWITCH, PDSO5, LEAD FREE, MO-178AA, SOT-23, 5 PIN
ROCHESTER
©2020 ICPDF网 联系我们和版权申明