ADL5356ACPZ-R2 [ADI]
1200 MHz to 2500 MHz, Dual-Balanced Mixer, LO Buffer, IF Amplifier, and RF Balun; 1200 MHz至2500 MHz的双平衡混频器, LO缓冲器, IF放大器和RF巴伦型号: | ADL5356ACPZ-R2 |
厂家: | ADI |
描述: | 1200 MHz to 2500 MHz, Dual-Balanced Mixer, LO Buffer, IF Amplifier, and RF Balun |
文件: | 总24页 (文件大小:399K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
1200 MHz to 2500 MHz, Dual-Balanced
Mixer, LO Buffer, IF Amplifier, and RF Balun
ADL5356
FEATURES
FUNCTIONAL BLOCK DIAGRAM
RF frequency range of 1200 MHz to 2500 MHz
IF frequency range of 30 MHz to 450 MHz
Power conversion gain: 8.2 dB
SSB noise figure of 9.9 dB
SSB noise figure with 5 dBm blocker of 21 dB
Input IP3 of 31 dBm
Input P1dB of 11 dBm
Typical LO drive of 0 dBm
Single-ended, 50 Ω RF and LO input ports
High isolation SPDT LO input switch
Single-supply operation: 3.3 V to 5 V
Exposed paddle, 6 mm × 6 mm, 36-lead LFCSP
36
35
34
33
32
31
30
29
28
1
2
3
4
5
6
7
8
9
27
26
25
24
23
22
21
20
19
MNIN
MNCT
COMM
VPOS
COMM
VPOS
COMM
DVCT
DVIN
LOI2
VGS2
VGS1
VGS0
LOSW
PWDN
VPOS
COMM
LOI1
APPLICATIONS
ADL5356
Cellular base station receivers
Transmit observation receivers
Radio link downconverters
10
11
12
13
14
15
16
17
18
GENERAL DESCRIPTION
Figure 1.
The ADL5356 uses a highly linear, doubly balanced, passive mixer
core along with integrated RF and local oscillator (LO) balancing
circuitry to allow single-ended operation. The ADL5356
incorporates the RF baluns, allowing for optimal performance over
a 1200 MHz to 2500 MHz RF input frequency range. Performance
is optimized for RF frequencies from 1700 MHz to 2500 MHz
using a low-side LO and RF frequencies from 1200 MHz to
1700 MHz using a high-side LO. The balanced passive mixer
arrangement provides good LO-to-RF leakage, typically better
than −35 dBm, and excellent intermodulation performance. The
balanced mixer core also provides extremely high input linearity,
allowing the device to be used in demanding cellular applications
where in-band blocking signals may otherwise result in the
degradation of dynamic performance. A high linearity IF buffer
amplifier follows the passive mixer core to yield a typical power
conversion gain of 8.2 dB and can be used with a wide range of
output impedances.
The ADL5356 is fabricated using a BiCMOS high performance
IC process. The device is available in a 6 mm × 6 mm, 36-lead
LFCSP and operates over a −40°C to +85°C temperature range.
An evaluation board is also available.
Table 1. Passive Mixers
RF Frequency
(MHz)
Single
Mixer
Single Mixer
and IF Amp
Dual Mixer
and IF Amp
500 to 1700
1200 to 2500
ADL5367
ADL5365
ADL5357
ADL5355
ADL5358
ADL5356
The ADL5356 provides two switched LO paths that can be used
in TDD applications where it is desirable to ping-pong between
two local oscillators. LO current can be externally set using a
resistor to minimize dc current commensurate with the desired
level of performance. For low voltage applications, the ADL5356 is
capable of operation at voltages down to 3.3 V with substantially
reduced current. Under low voltage operation, an additional logic
pin is provided to power down (<300 μA) the circuit when desired.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
©2009 Analog Devices, Inc. All rights reserved.
ADL5356
TABLE OF CONTENTS
Features .............................................................................................. 1
Circuit Description......................................................................... 17
RF Subsystem.............................................................................. 17
LO Subsystem ............................................................................. 18
Applications Information.............................................................. 19
Basic Connections...................................................................... 19
IF Port .......................................................................................... 19
Bias Resistor Selection ............................................................... 19
Mixer VGS Control DAC.......................................................... 19
Evaluation Board ............................................................................ 21
Outline Dimensions....................................................................... 23
Ordering Guide .......................................................................... 23
Applications....................................................................................... 1
General Description......................................................................... 1
Functional Block Diagram .............................................................. 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
5 V Performance........................................................................... 4
3.3 V Performance........................................................................ 4
Absolute Maximum Ratings............................................................ 5
ESD Caution.................................................................................. 5
Pin Configuration and Function Descriptions............................. 6
Typical Performance Characteristics ............................................. 7
5 V Performance........................................................................... 7
3.3 V Performance...................................................................... 15
Spur Tables .................................................................................. 16
REVISION HISTORY
10/09—Revision 0: Initial Version
Rev. 0 | Page 2 of 24
ADL5356
SPECIFICATIONS
VS = 5 V, IS = 350 mA, TA = 25°C, fRF = 1900 MHz, fLO = 1697 MHz, LO power = 0 dBm, RF power = −10 dBm, R1 = R4 = 1.3 kΩ, R2 =
R5 = 1 kΩ, ZO = 50 ꢀ, VGS0 = VGS1 = VGS2 = 0 V, unless otherwise noted.
Table 2.
Parameter
Conditions
Min
Typ
Max
Unit
RF INPUT INTERFACE
Return Loss
Tunable to >20 dB over a limited bandwidth
15
50
dB
Ω
MHz
Input Impedance
RF Frequency Range
OUTPUT INTERFACE
Output Impedance
IF Frequency Range
DC Bias Voltage1
LO INTERFACE
1200
2500
Differential impedance, f = 200 MHz
Externally generated
230||0.75
5.0
Ω||pF
MHz
V
30
3.3
450
5.5
LO Power
−6
0
+10
2470
0.4
dBm
dB
Ω
Return Loss
13
50
Input Impedance
LO Frequency Range
POWER-DOWN (PWDN) INTERFACE2
PWDN Threshold
Logic 0 Level
1230
MHz
1.0
V
V
Logic 1 Level
1.4
V
PWDN Response Time
Device enabled, IF output to 90% of its final level
Device disabled, supply current < 5 mA
Device enabled
160
230
0
ns
ns
μA
μA
PWDN Input Bias Current
Device disabled
70
1 Apply supply voltage from external circuit through choke inductors.
2 PWDN function is intended for use with VS ≤ 3.6 V only.
Rev. 0 | Page 3 of 24
ADL5356
5 V PERFORMANCE
VS = 5 V, IS = 350 mA, TA = 25°C, fRF = 1900 MHz, fLO = 1697 MHz, LO power = 0 dBm, RF power = −10 dBm, R1 = R4 = 1.3 kΩ, R2 = R5 = 1 kΩ,
VGS0 = VGS1 = VGS2 = 0 V, and ZO = 50 ꢀ, unless otherwise noted.
Table 3.
Parameter
Conditions
Min
Typ
Max
Unit
DYNAMIC PERFORMANCE
Power Conversion Gain
Voltage Conversion Gain
SSB Noise Figure
Including 4:1 IF port transformer and PCB loss
ZSOURCE = 50 Ω, differential ZLOAD = 200 Ω differential
7.5
8.2
14.5
9.9
21
8.5
dB
dB
dB
dB
SSB Noise Figure Under Blocking
5 dBm blocker present 10 MHz from wanted RF input,
LO source filtered
Input Third-Order Intercept (IIP3)
Input Second-Order Intercept (IIP2)
fRF1 = 1899.5 MHz, fRF2 = 1900.5 MHz, fLO = 1697 MHz,
each RF tone at −10 dBm
fRF1 = 1900 MHz, fRF2 = 1950 MHz, fLO = 1697 MHz,
each RF tone at −10 dBm
25
31
50
dBm
dBm
Input 1 dB Compression Point (IP1dB)
LO-to-IF Leakage
LO-to-RF Leakage
RF-to-IF Isolation
IF/2 Spurious
IF/3 Spurious
IF Channel-to-Channel Isolation
POWER SUPPLY
11
dBm
dBm
dBm
dBc
dBc
dBc
dB
Unfiltered IF output
−24
−35
−33
−75
−73
50
−10 dBm input power
−10 dBm input power
Positive Supply Voltage
Quiescent Current
4.75
5
5.25
V
LO supply
IF supply
VS = 5 V
170
180
350
mA
mA
mA
Total Quiescent Current
3.3 V PERFORMANCE
VS = 3.3 V, IS = 200 mA, TA = 25°C, fRF = 1900 MHz, fLO = 1697 MHz, LO power = 0 dBm, RF power = −10 dBm, R1 = R4 = 1.2 kΩ, R2 =
R5 = 400 Ω, VGS0 = VGS1 = VGS2 = 0 V, and ZO = 50 Ω, unless otherwise noted.
Table 4.
Parameter
Conditions
Min
Typ
Max
Unit
DYNAMIC PERFORMANCE
Power Conversion Gain
Voltage Conversion Gain
SSB Noise Figure
Including 4:1 IF port transformer and PCB loss
ZSOURCE = 50 Ω, differential ZLOAD = 200 Ω differential
8.3
14.6
8.9
dB
dB
dB
Input Third-Order Intercept (IIP3)
fRF1 = 1899.5 MHz, fRF2 = 1900.5 MHz, fLO = 1697 MHz,
each RF tone at −10 dBm
21.2
dBm
Input Second-Order Intercept (IIP2)
fRF1 = 1950 MHz, fRF2 = 1900 MHz, fLO = 1697 MHz,
each RF tone at −10 dBm
48
7
dBm
dBm
Input 1 dB Compression Point (IP1dB)
POWER INTERFACE
Supply Voltage
3.0
3.3
3.6
V
Quiescent Current
Total Quiescent Current
Resistor programmable
Device disabled
200
300
mA
μA
Rev. 0 | Page 4 of 24
ADL5356
ABSOLUTE MAXIMUM RATINGS
ESD CAUTION
Table 5.
Parameter
Rating
Supply Voltage, VS
5.5 V
RF Input Level
LO Input Level
20 dBm
13 dBm
6.0 V
5.5 V
2.2 W
22°C/W
150°C
−40°C to +85°C
−65°C to +150°C
260°C
MNOP, MNON, DVOP, DVON Bias
VGS2,VGS1,VGS0, LOSW, PWDN
Internal Power Dissipation
θJA
Maximum Junction Temperature
Operating Temperature Range
Storage Temperature Range
Lead Temperature (Soldering, 60 sec)
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Rev. 0 | Page 5 of 24
ADL5356
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
1
2
3
4
5
6
7
8
9
27 LOI2
VGS2
MNIN
MNCT
COMM
VPOS
COMM
VPOS
COMM
DVCT
DVIN
26
25 VGS1
VGS0
ADL5356
TOP VIEW
(Not to Scale)
24
23 LOSW
22 PWDN
21 VPOS
20
19
COMM
LOI1
NOTES
1. NC = NO CONNECT.
2. EXPOSED PAD MUST BE CONNECTED TO GROUND.
Figure 2. Pin Configuration
Table 6. Pin Function Descriptions
Pin No.
Mnemonic
Description
1
2
MNIN
MNCT
RF Input for Main Channel. Internally matched to 50 Ω. Must be ac-coupled.
Center Tap for Main Channel Input Balun. Bypass to ground using low inductance capacitor.
Device Common (DC Ground).
3, 5, 7, 12, 20, 34 COMM
4, 6, 10, 16,
21, 30, 36
VPOS
Positive Supply Voltage.
8
9
DVCT
DVIN
Center Tap for Diversity Channel Input Balun. Bypass to ground using low inductance capacitor.
RF Input for Diversity Channel. Internally matched to 50 Ω. Must be ac-coupled.
11
DVGM
Diverstiy Amplifier Bias Setting. Connect 1.3 kΩ resistor to ground for typical operation.
13, 14
DVOP, DVON
Diversity Channel Differential Open-Collector Outputs. DVOP and DVON should be pulled-up to
VCC using external inductors.
15
17
18, 28
19
DVLE
DVLG
NC
Diversity Channel IF Return. This pin must be grounded.
Diverstiy Channel LO Buffer Bias Setting. Connect 1 kΩ resistor to ground for typical operation.
No Connect.
LOI1
Local Oscillator Input 1. Internally matched to 50 Ω. Must be ac-coupled.
22
PWDN
Connect to Ground for Normal Operation. Connect pin to 3 V for disable mode when using
VPOS < 3.6 V. PWDN pin must be grounded when VPOS > 3.6 V.
23
LOSW
Local Oscillator Input Selection Switch. Set LOSW high to select LOI1 or set LOSW low to select LOI2.
24, 25, 26
27
29
VGS0, VGS1, VGS2 Gate to Source Control Voltages. For typical operation, set VGS0, VGS1, and VGS2 to low logic level.
LOI2
Local Oscillator Input 2. Internally matched to 50 Ω. Must be ac-coupled.
Main Channel LO Buffer Bias Setting. Connect 1 kΩ resistor to ground for typical operation.
Main Channel IF Return. This pin must be grounded.
MNLG
MNLE
31
32, 33
MNOP, MNON
Main Channel Differential Open-Collector Outputs. MNOP and MNON should be pulled-up to
VCC using external inductors.
35
Paddle
MNGM
EPAD
Main Amplifier Bias Setting. Connect 1.3 kΩ resistor to ground for typical operation.
Exposed pad must be connected to ground.
Rev. 0 | Page 6 of 24
ADL5356
TYPICAL PERFORMANCE CHARACTERISTICS
5 V PERFORMANCE
VS = 5 V, IS = 350 mA, TA = 25°C, fRF = 1900 MHz, fLO = 1697 MHz, LO power = 0 dBm, RF power = −10 dBm, R1 = R4 = 1.3 kꢀ, R2 = R5 = 1 kꢀ,
ZO = 50 ꢀ, VGS0 = VGS1 = VGS2 = 0 V, unless otherwise noted.
61
59
57
55
53
51
49
400
380
360
340
320
300
T
= –40°C
A
T
T
= +25°C
= +85°C
A
T
= –40°C
A
T
= +25°C
A
A
T
= +85°C
A
1700 1750 1800 1850 1900 1950 2000 2050 2100 2150 2200
1700 1750 1800 1850 1900 1950 2000 2050 2100 2150 2200
RF FREQUENCY (MHz)
RF FREQUENCY (MHz)
Figure 6. Input IP2 vs. RF Frequency
Figure 3. Supply Current vs. RF Frequency
13.0
12.5
12.0
11.5
11.0
10.5
10.0
9.5
11
10
9
T
= +25°C
A
T
= –40°C
A
T
= +85°C
A
T
= +25°C
A
8
T
= –40°C
A
7
T
= +85°C
A
6
9.0
5
1700 1750 1800 1850 1900 1950 2000 2050 2100 2150 2200
1700 1750 1800 1850 1900 1950 2000 2050 2100 2150 2200
RF FREQUENCY (MHz)
RF FREQUENCY (MHz)
Figure 7. Input P1dB vs. RF Frequency
Figure 4. Power Conversion Gain vs. RF Frequency
14
45
13
12
11
10
9
40
35
30
25
20
15
T
= –40°C
A
T
= +85°C
A
T
= +25°C
A
T
= +25°C
A
T
= –40°C
A
8
T
= +85°C
A
7
6
5
1700 1750 1800 1850 1900 1950 2000 2050 2100 2150 2200
1700 1750 1800 1850 1900 1950 2000 2050 2100 2150 2200
RF FREQUENCY (MHz)
RF FREQUENCY (MHz)
Figure 8. SSB Noise Figure vs. RF Frequency
Figure 5 .Input IP3 vs. RF Frequency
Rev. 0 | Page 7 of 24
ADL5356
VS = 5 V, IS = 350 mA, TA = 25°C, fRF = 1900 MHz, fLO = 1697 MHz, LO power = 0 dBm, RF power = −10 dBm, R1 = R4 = 1.3 kꢀ, R2 = R5 = 1 kꢀ,
ZO = 50 ꢀ, VGS0 = VGS1 = VGS2 = 0 V, unless otherwise noted.
400
380
360
340
320
300
58
57
56
55
54
53
V
= 5.25V
POS
V
= 5.25V
POS
V
= 5.0V
POS
V
V
= 5.00V
= 4.75V
POS
V
= 4.75V
POS
POS
52
51
50
49
–40 –30 –20 –10
0
10 20 30 40 50 60 70 80
TEMPERATURE (°C)
–40 –30 –20 –10
0
10 20 30 40 50 60 70 80
TEMPERATURE (°C)
Figure 9. Supply Current vs. Temperature
Figure 12. Input IP2 vs. Temperature
10.0
14
13
12
11
10
9
4.75V
5.00V
5.25V
9.5
9.0
9.5
8.0
7.5
7.0
V
= 5.25V
POS
V
= 5.0V
POS
V
= 4.75V
POS
8
–40 –30 –20 –10
0
10 20 30 40 50 60 70 80
TEMPERATURE (°C)
–40 –30 –20 –10
0
10 20 30 40 50 60 70 80
TEMPERATURE (°C)
Figure 10. Power Conversion Gain vs. Temperature
Figure 13. Input P1dB vs. Temperature
40
12.0
11.5
11.0
10.5
10.0
9.5
38
36
34
32
30
28
26
24
V
= 5.25V
POS
V
= 5.25V
POS
V
= 5.0V
POS
V
= 4.75V
POS
V
= 5.0V
POS
9.0
V
= 4.75V
POS
8.5
8.0
7.5
7.0
–40 –30 –20 –10
0
10 20 30 40 50 60 70 80
TEMPERATURE (°C)
–40 –30 –20 –10
0
10 20 30 40 50 60 70 80
TEMPERATURE (°C)
Figure 11. Input IP3 vs. Temperature
Figure 14. SSB Noise Figure vs. Temperature
Rev. 0 | Page 8 of 24
ADL5356
VS = 5 V, IS = 350 mA, TA = 25°C, fRF = 1900 MHz, fLO = 1697 MHz, LO power = 0 dBm, RF power = −10 dBm, R1 = R4 = 1.3 kꢀ, R2 = R5 = 1 kꢀ,
ZO = 50 ꢀ, VGS0 = VGS1 = VGS2 = 0 V, unless otherwise noted.
400
70
65
60
55
50
45
380
360
340
320
300
T
= –40°C
A
T
= +25°C
A
T
= +25°C
A
T
= –40°C
A
T
= +85°C
A
T
= +85°C
A
40
30
80
130
180
230
280
330
380
430
30
30
30
80
80
80
130
180
230
280
330
380
430
IF FREQUENCY (MHz)
IF FREQUENCY (MHz)
Figure 15. Supply Current vs. IF Frequency
Figure 18. Input IP2 vs. IF Frequency
10
9
8
7
6
5
4
3
2
1
0
14
13
12
11
10
9
T
= –40°C
A
T
= +85°C
A
T
= +25°C
A
T
= +85°C
A
T
= +25°C
A
T
= –40°C
A
8
30
80
130
180
230
280
330
380
430
130
180
230
280
330
380
430
IF FREQUENCY (MHz)
IF FREQUENCY (MHz)
Figure 16. Power Conversion Gain vs. IF Frequency
Figure 19. Input P1dB vs. IF Frequency
40
35
30
25
20
15
10
5
14
13
12
11
10
9
T
= –40°C
A
T
= +25°C
A
T
= +85°C
A
8
7
0
6
30
80
130
180
230
280
330
380
430
130
180
230
280
330
380
430
IF FREQUENCY (MHz)
IF FREQUENCY (MHz)
Figure 17. Input IP3 vs. IF Frequency
Figure 20. SSB Noise Figure vs. IF Frequency
Rev. 0 | Page 9 of 24
ADL5356
VS = 5 V, IS = 350 mA, TA = 25°C, fRF = 1900 MHz, fLO = 1697 MHz, LO power = 0 dBm, RF power = −10 dBm, R1 = R4 = 1.3 kꢀ, R2 = R5 = 1 kꢀ,
ZO = 50 ꢀ, VGS0 = VGS1 = VGS2 = 0 V, unless otherwise noted.
11
10
9
11.8
T
= +85°C
A
11.6
11.4
11.2
11.0
10.8
10.6
10.4
10.2
T
= +25°C
A
T
= –40°C
A
T
= –40°C
A
8
T
= +25°C
A
7
T
= +85°C
A
6
5
10.0
–6
–4
–2
0
2
4
6
8
10
–6
–4
–2
0
2
4
6
8
10
LO POWER (dBm)
LO POWER (dBm)
Figure 21. Power Conversion Gain vs. LO Power
Figure 24. Input P1dB vs. LO Power
40
–55
–60
–65
38
36
34
32
30
28
26
24
22
20
T
= –40°C
A
T
= –40°C
A
–70
–75
–80
T
= +25°C
A
T
= +25°C
A
T
= +85°C
A
T
= +85°C
A
–85
–6
–4
–2
0
2
4
6
8
10
1700 1750 1800 1850 1900 1950 2000 2050 2100 2100 2200
LO POWER (dBm)
RF FREQUENCY (MHz)
Figure 25. IF/2 Spurious vs. RF Frequency, RF Power = −10 dBm
Figure 22. Input IP3 vs. LO Power
–65
–66
–67
65
63
61
59
57
55
53
51
49
47
45
T
= –40°C
A
–68
–69
–70
–71
–72
–73
–74
–75
T
= +85°C
A
T
= +25°C
A
T
= +85°C
A
T
= –40°C
A
T
= +25°C
A
1700 1750 1800 1850 1900 1950 2000 2050 2100 2100 2200
–6
–4
–2
0
2
4
6
8
10
RF FREQUENCY (MHz)
LO POWER (dBm)
Figure 26. IF/3 Spurious vs. RF Frequency, RF Power = −10 dBm
Figure 23. Input IP2 vs. LO Power
Rev. 0 | Page 10 of 24
ADL5356
VS = 5 V, IS = 350 mA, TA = 25°C, fRF = 1900 MHz, fLO = 1697 MHz, LO power = 0 dBm, RF power = −10 dBm, R1 = R4 = 1.3 kꢀ, R2 = R5 = 1 kꢀ,
ZO = 50 ꢀ, VGS0 = VGS1 = VGS2 = 0 V, unless otherwise noted.
100
80
60
40
20
0
500
400
300
200
100
0
10
MEAN = 8.26
SD = 0.31%
8
6
4
2
0
30
80
130
180
230
280
330
380
430
7.6
7.8
8.0
8.2
8.4
8.6
8.8
45
13
IF FREQUENCY (MHz)
CONVERSION GAIN (dB)
Figure 30. IF Output Impedance (R Parallel C Equivalent)
Figure 27. Conversion Gain Distribution
0
5
100
80
60
40
20
0
MEAN = 31.67
SD = 0.35%
10
15
20
25
30
1700 1750 1800 1850 1900 1950 2000 2050 2100 2150 2200
20
25
30
35
40
RF FREQUENCY (MHz)
INPUT IP3 LO (dBm)
Figure 28. Input IP3 Distribution
Figure 31. RF Port Return Loss, Fixed IF
100
80
60
40
20
0
0
MEAN = 11.37
SD = 0.49%
5
10
SELECTED
15
20
25
UNSELECTED
10
11
12
1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00
LO FREQUENCY (GHz)
INPUT P1dB (dBm)
Figure 32. LO Return Loss, Selected and Unselected
Figure 29. Input P1dB Distribution
Rev. 0 | Page 11 of 24
ADL5356
VS = 5 V, IS = 350 mA, TA = 25°C, fRF = 1900 MHz, fLO = 1697 MHz, LO power = 0 dBm, RF power = −10 dBm, R1 = R4 = 1.3 kꢀ, R2 = R5 = 1 kꢀ,
ZO = 50 ꢀ, VGS0 = VGS1 = VGS2 = 0 V, unless otherwise noted.
60
50
40
30
20
10
0
–15
–20
–25
–30
–35
–40
–45
–50
T
= +25°C
A
T
= –40°C
A
T
= +85°C
A
T
= –40°C
A
T
= +25°C
A
T
= +85°C
A
1500 1550 1600 1650 1700 1750 1800 1850 1900 1950 2000
1700 1750 1800 1850 1900 1950 2000 2050 2100 2150 2200
LO FREQUENCY (MHz)
RF FREQUENCY (MHz)
Figure 33. LO Switch Isolation vs. RF Frequency
Figure 36. LO-to-RF Leakage vs. LO Frequency
–16
26
28
30
32
34
36
38
40
–18
–20
–22
–24
–26
–28
–30
2XLO-TO-IF
T
= +85°C
A
2XLO-TO-RF
T
= +25°C
A
T
= –40°C
A
1700 1750 1800 1850 1900 1950 2000 2050 2100 2150 2200
1500 1550 1600 1650 1700 1750 1800 1850 1900 1950 2000
RF FREQUENCY (MHz)
LO FREQUENCY (MHz)
Figure 34. RF-to-IF Isolation vs. RF Frequency
Figure 37. 2XLO Leakage vs. LO Frequency
–10
–35
–40
–45
–50
–55
–60
–65
–70
–15
–20
–25
–30
–35
–40
T
= –40°C
A
3XLO-TO-IF
T
= +25°C
A
T
= +85°C
A
3XLO-TO-RF
1500 1550 1600 1650 1700 1750 1800 1850 1900 1950 2000
1500 1550 1600 1650 1700 1750 1800 1850 1900 1950 2000
LO FREQUENCY (MHz)
LO FREQUENCY (MHz)
Figure 35. LO-to-IF Leakage vs. LO Frequency
Figure 38. 3XLO Leakage vs. LO Frequency
Rev. 0 | Page 12 of 24
ADL5356
VS = 5 V, IS = 350 mA, TA = 25°C, fRF = 1900 MHz, fLO = 1697 MHz, LO power = 0 dBm, RF power = −10 dBm, R1 = R4 = 1.3 kꢀ, R2 = R5 = 1 kꢀ,
ZO = 50 ꢀ, VGS0 = VGS1 = VGS2 = 0 V, unless otherwise noted.
30
25
20
15
10
5
10
18
16
14
12
10
8
9
8
7
6
VGS = 000
VGS = 011
VGS = 100
VGS = 110
5
0
4
6
1700 1750 1800 1850 1900 1950 2000 2050 2100 2150 2200
–30
–25
–20
–15
–10
–5
0
5
10
BLOCKER POWER (dBm)
RF FREQUENCY (MHz)
Figure 42. SSB Noise Figure vs. 10 MHz Offset Blocker Level
Figure 39. Power Conversion Gain and SSB Noise Figure vs. RF Frequency
for Various VGS Settings
350
20
18
16
14
12
10
8
32
30
28
26
24
22
20
18
300
250
200
150
100
50
IF RESISTOR SUPPLY CURRENT
LO RESISTOR SUPPLY CURRENT
VGS = 000
VGS = 011
VGS = 100
VGS = 110
0
6
600 700 800 900 1000 1100 1200 1300 1400 1500 1600
1700 1750 1800 1850 1900 1950 2000 2050 2100 2150 2200
BIAS RESISTOR VALUE (Ω)
RF FREQUENCY (MHz)
Figure 43. LO and IF Supply Current vs. IF and LO Bias Resistor Value
Figure 40. Input IP3 and Input P1dB vs. RF Frequency for Various VGS Settings
35
13
12
11
10
9
35
30
25
20
15
10
5
13
INPUT IP3
INPUT IP3
30
12
25
11
NOISE FIGURE
NOISE FIGURE
20
15
10
5
10
9
CONVERSION GAIN
CONVERSION GAIN
8
8
7
7
6
0
6
0
600 700 800 900 1000 1100 1200 1300 1400 1500 1600
600 700 800 900 1000 1100 1200 1300 1400 1500 1600
LO BIAS RESISTOR VALUE (Ω)
IF BIAS RESISTOR VALUE (Ω)
Figure 41. Power Conversion Gain, SSB Noise Figure, and Input IP3 vs.
LO Bias Resistor Value
Figure 44. Power Conversion Gain, Noise Figure, and Input IP3 vs.
IF Bias Resistor Value
Rev. 0 | Page 13 of 24
ADL5356
VS = 5 V, IS = 350 mA, TA = 25°C, fRF = 1900 MHz, fLO = 1697 MHz, LO power = 0 dBm, RF power = −10 dBm, R1 = R4 = 1.3 kꢀ, R2 = R5 = 1 kꢀ,
ZO = 50 ꢀ, VGS0 = VGS1 = VGS2 = 0 V, unless otherwise noted.
54
53
52
51
50
49
48
47
46
T = –40°C
A
T
= +85°C
A
T
= +25°C
A
1700 1750 1800 1850 1900 1950 2000 2050 2100 2150 2200
RF FREQUENCY (MHz)
Figure 45. IF Channel-to-Channel Isolation vs. RF Frequency
Rev. 0 | Page 14 of 24
ADL5356
3.3 V PERFORMANCE
VS = 3.3 V, IS = 200 mA, TA = 25°C, fRF = 1900 MHz, fLO = 1697 MHz, LO power = 0 dBm, RF power = −10 dBm, R1 = R4 = 1.2 kꢀ,
R2 = R5 = 400 ꢀ, ZO = 50 ꢀ, VGS0 = VGS1 = VGS2 = 0 V, unless otherwise noted.
215
210
205
200
195
190
70
65
60
55
50
45
40
35
30
T
= +85°C
A
T
= –40°C
A
T
= –40°C
A
T
= +25°C
A
T
T
= +25°C
= +85°C
A
A
1700 1750 1800 1850 1900 1950 2000 2050 2100 2150 2200
1700 1750 1800 1850 1900 1950 2000 2050 2100 2150 2200
RF FREQUENCY (MHz)
RF FREQUENCY (MHz)
Figure 46. Supply Current vs. RF Frequency at 3.3 V
Figure 49. Input IP2 vs. RF Frequency at 3.3 V
11
10
9
14
12
10
8
T
= –40°C
A
T
= +25°C
A
8
T
= +25°C
A
7
6
T
= +85°C
A
T
= –40°C
A
6
4
T
= +85°C
A
5
2
4
0
1700 1750 1800 1850 1900 1950 2000 2050 2100 2150 2200
1700 1750 1800 1850 1900 1950 2000 2050 2100 2150 2200
RF FREQUENCY (MHz)
RF FREQUENCY (MHz)
Figure 47. Power Conversion Gain vs. RF Frequency at 3.3 V
Figure 50. Input P1dB vs. RF Frequency at 3.3 V
30
28
26
24
14
12
10
8
T
= +85°C
A
T
= –40°C
A
22
20
18
16
14
12
10
T
= +25°C
A
T
= +25°C
A
T
= –40°C
A
6
T
= +85°C
A
4
2
1700 1750 1800 1850 1900 1950 2000 2050 2100 2150 2200
1700 1750 1800 1850 1900 1950 2000 2050 2100 2150 2200
RF FREQUENCY (MHz)
RF FREQUENCY (MHz)
Figure 48. Input IP3 vs. RF Frequency at 3.3 V
Figure 51. SSB Noise Figure vs. RF Frequency at 3.3 V
Rev. 0 | Page 15 of 24
ADL5356
SPUR TABLES
All spur tables are (N × fRF) − (M × fLO) and were measured using the standard evaluation board. Mixer spurious products are measured
in dBc from the IF output power level. Data was measured only for frequencies less than 6 GHz. Typical noise floor of the measurement
system = −100 dBm.
5 V Performance
VS = 5 V, IS = 350 mA, TA = 25°C, fRF = 1900 MHz, fLO = 1697 MHz, LO power = 0 dBm, RF power = −10 dBm, VGS0 = VGS1 = VGS2 = 0 V,
and ZO = 50 ꢀ, unless otherwise noted.
M
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
0
−21.6
0.00
−91.0
−20.2
−72.7
−74.4
−64.4
−45.9
−82.9
1
−40.7
−70.5
−69.6
−86.4
−96.5
2
<−100
<−100
3
<−100 <−100 <−100 −79.3
4
<−100 <−100 <−100 <−100 <−100 <−100 <−100 <−100
<−100 <−100 <−100 <−100 <−100 <−100 <−100
<−100 <−100 <−100 <−100 <−100 <−100 <−100
5
6
7
<−100 <−100 <−100 <−100 <−100 <−100 <−100
<−100 <−100 <−100 <−100 <−100 <−100
N
8
9
<−100 <−100 <−100 <−100 <−100 <−100
<−100 <−100 <−100 <−100 <−100 <−100
10
11
12
13
14
15
<−100 <−100 <−100 <−100 <−100 <−100
<−100 <−100 <−100 <−100 <−100
<−100 <−100 <−100
<−100 <−100
<−100
3.3 V Performance
VS = 3.3 V, IS = 200 mA, TA = 25°C, fRF = 1900 MHz, fLO = 1697 MHz, LO power = 0 dBm, RF power = −10 dBm, R1 = R4 = 1.2 kꢀ, R2 =
R5 = 400 ꢀ, VGS0 = VGS1 = VG2 = 0 V, and ZO = 50 ꢀ, unless otherwise noted.
M
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
0
−9.84
−20.31 −43.05 −40.75 −64.36
−47.95 −37.36 −53.08 −57.08 −74.07
−74.64 −56.52 −57.35 −64.17 −80.85 −91.01 −85.58 <−100
1
−49.63 0.00
2
3
<−100
<−100
<−100
<−100
−88.31 −98.10 −62.72 <−100
−91.46 <−100
<−100
<−100 <−100
<−100 <−100 <−100
<−100 <−100 <−100 <−100
4
<−100
<−100
<−100
<−100
<−100
<−100
<−100
<−100
<−100
<−100
<−100
<−100
<−100
<−100
<−100
<−100
<−100
−99.73 <−100
<−100
<−100
<−100
<−100
<−100
<−100
<−100
<−100
<−100
<−100
<−100
5
<−100
<−100
<−100
<−100
<−100
<−100
<−100
<−100
<−100
<−100
<−100
<−100
<−100
<−100
<−100
6
7
<−100 <−100 <−100 <−100 <−100
<−100 <−100 <−100 <−100 <−100
N
8
9
<−100 <−100 <−100 <−100 <−100 <−100
<−100 <−100 <−100 <−100 <−100 <−100 <−100
10
11
12
13
14
15
<−100 <−100 <−100 <−100 <−100 <−100 <−100 <−100
<−100 <−100 <−100 <−100 <−100 <−100 <−100 <−100
<−100 <−100 <−100 <−100 <−100 <−100 <−100 <−100
<−100 <−100 <−100 <−100 <−100 <−100 <−100 <−100
<−100 <−100 <−100 <−100 <−100 <−100 <−100 <−100
Rev. 0 | Page 16 of 24
ADL5356
CIRCUIT DESCRIPTION
The ADL5356 consists of two primary components: the radio
frequency (RF) subsystem and the local oscillator (LO) subsystem.
The combination of design, process, and packaging technology
allows the functions of these subsystems to be integrated into
a single die using mature packaging and interconnection
technologies to provide a high performance, low cost design
with excellent electrical, mechanical, and thermal properties.
In addition, the need for external components is minimized,
optimizing cost and size.
The resulting balanced RF signal is applied to a passive mixer that
commutates the RF input with the output of the LO subsystem.
The passive mixer is essentially a balanced, low loss switch that
adds minimum noise to the frequency translation. The only
noise contribution from the mixer is due to the resistive loss of
the switches, which is in the order of a few ohms.
Because the mixer is inherently broadband and bidirectional, it
is necessary to properly terminate all the idler (M × N product)
frequencies generated by the mixing process. Terminating the
mixer avoids the generation of unwanted intermodulation
products and reduces the level of unwanted signals at the input
of the IF amplifier, where high peak signal levels can compromise
the compression and intermodulation performance of the system.
This termination is accomplished by the addition of a sum network
between the IF amplifier and the mixer and in the feedback
elements in the IF amplifier.
The RF subsystem consists of integrated, low loss RF baluns,
passive MOSFET mixers, sum termination networks, and IF
amplifiers. The LO subsystem consists of an SPDT-terminated FET
switch and two multistage limiting LO amplifiers. The purpose of
the LO subsystem is to provide a large, fixed amplitude, balanced
signal to drive the mixer independent of the level of the LO input.
A block diagram of the device is shown in Figure 52.
The IF amplifier is a balanced feedback design that simultaneously
provides the desired gain, noise figure, and input impedance that
is required to achieve the overall performance. The balanced open-
collector output of the IF amplifier, with impedance modified
by the feedback within the amplifier, permits the output to be
connected directly to a high impedance filter, differential amplifier,
or an analog-to-digital input while providing optimum second-
order intermodulation suppression. The differential output
impedance of the IF amplifier is approximately 200 Ω. If
operation in a 50 Ω system is desired, the output can be
transformed to 50 Ω by using a 4:1 transformer.
36
35
34
33
32
31
30
29
28
1
2
3
4
5
6
7
8
9
27
26
25
24
23
22
21
20
19
MNIN
MNCT
COMM
VPOS
COMM
VPOS
COMM
DVCT
DVIN
LOI2
VGS2
VGS1
VGS0
LOSW
PWDN
VPOS
COMM
LOI1
The intermodulation performance of the design is generally limited
by the IF amplifier. The IP3 performance can be optimized by
adjusting the IF current with an external resistor. Figure 41,
Figure 43, and Figure 44 illustrate how various IF and LO bias
resistors affect the performance with a 5 V supply. Additionally,
dc current can be saved by increasing either or both resistors. It
is permissible to reduce the dc supply voltage to as low as 3.3 V,
further reducing the dissipated power of the part. (No performance
enhancement is obtained by reducing the value of these resistors,
and excessive dc power dissipation may result.)
ADL5356
10
11
12
13
14
15
16
17
18
Figure 52. Simplified Schematic
RF SUBSYSTEM
The single-ended, 50 Ω RF input is internally transformed to a
balanced signal using a low loss (<1 dB) unbalanced-to-balanced
(balun) transformer. This transformer is made possible by an
extremely low loss metal stack, which provides both excellent
balance and dc isolation for the RF port. Although the port can be
dc connected, it is recommended that a blocking capacitor be used
to avoid running excessive dc current through the part. The RF
balun can easily support an RF input frequency range of 1200 MHz
to 2500 MHz.
Rev. 0 | Page 17 of 24
ADL5356
The performance of this amplifier is critical in achieving a
high intercept passive mixer without degrading the noise floor
of the system. This is a critical requirement in an interferer rich
environment, such as cellular infrastructure, where blocking
interferers can limit mixer performance. The bandwidth of the
intermodulation performance is somewhat influenced by the
current in the LO amplifier chain. For dc current sensitive
applications, it is permissible to reduce the current in the LO
amplifier by raising the value of the external bias control resistor.
For dc current critical applications, the LO chain can operate
with a supply voltage as low as 3.3 V, resulting in substantial
dc power savings.
LO SUBSYSTEM
The LO amplifier is designed to provide a large signal level to
the mixer to obtain optimum intermodulation performance.
The resulting amplifier provides extremely high performance
centered on an operating frequency of 1700 MHz. The best
operation is achieved with either low-side LO injection for RF
signals in the 1700 MHz to 2500 MHz range or high-side injection
for RF signals in the 1200 MHz to 1700 MHz range. Operation
outside these ranges is permissible, and conversion gain is
extremely wideband, easily spanning 1200 MHz to 2500 MHz,
but intermodulation is optimal over the aforementioned ranges.
The ADL5356 has two LO inputs permitting multiple synthesizers
to be rapidly switched with extremely short switching times
(<40 ns) for frequency agile applications. The two inputs are
applied to a high isolation SPDT switch that provides a constant
input impedance, regardless of whether the port is selected, to
avoid pulling the LO sources. This multiple section switch also
ensures high isolation to the off input, minimizing any leakage
from the unwanted LO input that may result in undesired IF
responses.
In addition, when operating with supply voltages below 3.6 V, the
ADL5356 has a power-down mode that permits the dc current
to drop to <300 μA.
The logic inputs are designed to work with any logic family that
provides a Logic 0 input level of less than 0.4 V and a Logic 1
input level that exceeds 1.4 V. All logic inputs are high impedance
up to Logic 1 levels of 3.3 V. At levels exceeding 3.3 V, protection
circuitry permits operation up to 5.5 V, although a small bias
current is drawn.
The single-ended LO input is converted to a fixed amplitude
differential signal using a multistage, limiting LO amplifier. This
results in consistent performance over a range of LO input power.
Optimum performance is achieved from −6 dBm to +10 dBm,
but the circuit continues to function at considerably lower levels
of LO input power.
Rev. 0 | Page 18 of 24
ADL5356
APPLICATIONS INFORMATION
BASIC CONNECTIONS
BIAS RESISTOR SELECTION
The IF bias resistors (R1 and R4) and LO bias resistors (R2 and R5)
are used to adjust the bias current of the integrated amplifiers at the
IF and LO terminals. It is necessary to have a sufficient amount
of current to bias both the internal IF and LO amplifiers to optimize
dc current vs. optimum IIP3 performance. Figure 41, Figure 43,
and Figure 44 provide the reference for the bias resistor selection
when lower power consumption is considered at the expense of
conversion gain and IP3 performance.
The ADL5356 mixer is designed to downconvert radio
frequencies (RF) primarily between 1200 MHz and 2500 MHz
to lower intermediate frequencies (IF) between 30 MHz and
450 MHz. Figure 53 depicts the basic connections of the mixer.
It is recommended to ac-couple the RF and LO input ports to
prevent non-zero dc voltages from damaging the RF balun or
LO input circuit. The RFIN matching network consists of a
series 1.8 pF capacitor and a shunt 15 nH inductor to provide
the optimized RF input return loss for the desired frequency band.
MIXER VGS CONTROL DAC
IF PORT
The ADL5356 features three logic control pins, VGS0 (Pin 24),
VGS1 (Pin 25), and VGS2 (Pin26), that allow programmability for
internal gate-to-source voltages for optimizing mixer performance
over desired frequency bands. The evaluation board defaults
VGS0, VGS1, and VGS2 to ground. Power conversion gain, NF,
IIP3, and input P1dB can be optimized, as shown in Figure 39
and Figure 40.
The mixer differential IF interface requires pull-up choke inductors
to bias the open-collector outputs and to set the output match.
The shunting impedance of the choke inductors used to couple
dc current into the IF amplifier should be selected to provide
the desired output return loss.
The real part of the output impedance is approximately 200 ꢀ,
as seen in Figure 30, which matches many commonly used SAW
filters without the need for a transformer. This results in a voltage
conversion gain that is approximately 6 dB higher than the power
conversion gain, as shown in Table 3. When a 50 ꢀ output
impedance is needed, use a 4:1 impedance transformer, as shown
in Figure 53.
Rev. 0 | Page 19 of 24
ADL5356
R10
MAIN_OUTN
MAIN_OUTP
C33
C32
T1
C19
C17
C27
C8
C21
L2
L1
R3
VCC
C25
C18
R1
C22
VCC
L6
R2
28
VCC
36
35
34
33
32
31
30
29
C9
C16
1
2
27
26
25
24
23
22
21
20
19
MAIN_IN
LO2
Z1
Z2
R12
R7
R16
C34
VCC
C3
C2
R13
R8
3
4
5
6
7
8
9
R14
R11
R17
R15
VCC
R19
VCC
C26
C15
C6
C7
ADL5356
C11
LO1
DIV_IN
C14
Z3
Z4
10
11
12
13
14
15
L3
C24
16
17
18
VCC
+
VCC
R5
VCC
C23
R4
C10
VCC
R6
C13
GND
L5
L4
C1
C12
C28
C20
C29
T2
DIV_OUTP
DIV_OUTN
C30
C31
R9
Figure 53. Typical Application Circuit
Rev. 0 | Page 20 of 24
ADL5356
EVALUATION BOARD
An evaluation board is available for the family of double balanced
mixers. The standard evaluation board schematic is shown in
Figure 54. The evaluation board is fabricated using Rogers®
RO3003 material. Table 7 describes the various configuration
options of the evaluation board. Evaluation board layout is shown
in Figure 55 and Figure 56.
R10
MAIN_OUTN
MAIN_OUTP
C33
C32
T1
C19
C17
C27
C8
C21
L2
L1
R3
VCC
C25
C18
R1
C22
VCC
L6
R2
VCC
C9
C16
LOI2
MNIN
MAIN_IN
LO2
R12
R7
R16
C34
Z1
Z2
C3
VGS2
VGS1
VGS0
LOSW
PWDN
VPOS
COMM
LOI1
VCC
MNCT
COMM
VPOS
COMM
VPOS
COMM
DVCT
DVIN
C2
R13
R8
R14
R11
R17
ADL5356
TOP VIEW
(Not to Scale)
VCC
R15
C6
C7
R19
VCC
C11
C26
C15
DIV_IN
Z3
Z4
LO1
C14
VCC
VCC
C23
L3
R5
+
C10
R4
VCC
VCC
GND
C24
C13
R6
L4
L5
C1
C12
C28
C20
C29
T2
DIV_OUTP
DIV_OUTN
C30
C31
R9
Figure 54. Evaluation Board Schematic
Rev. 0 | Page 21 of 24
ADL5356
Table 7. Evaluation Board Configuration
Components
Description
Default Conditions
C1, C8, C10, C12,
C13, C15, C18,
C21, C22, C23,
C24, C25, C26
Power Supply Decoupling. Nominal supply decoupling consists of a C10 = 4.7 μF (Size 3216),
0.01 μF capacitor to ground in parallel with 10 pF capacitors to
ground positioned as close to the device as possible.
C1, C8, C12, C21 = 150 pF (Size 0402),
C22, C23, C24, C25, C26 = 10 pF (Size 0402),
C13, C15, C18 = 0.1 μF (Size 0402)
Z1 to Z4, C2, C3,
C6, C7, C9, C11
RF Main and Diversity Input Interface. Main and diversity
input channels are ac-coupled through C9 and C11. Z1 to
Z4 provide additional component placement for external
matching/filter networks. C2, C3, C6, and C7 provide bypassing
for the center taps of the main and diversity on-chip input baluns.
C2, C7 = 10 pF (Size 0402),
C3, C6 = 0.01 μF (Size 0402),
C9, C11 = 1.8 pF (Size 0402),
Z2, Z4 = 15 nH,
Z1, Z3 = open (Size 0402)
T1, T2, C17, C19,
C20, C27 - C33,
L1, L2, L4, L5,
IF Main and Diversity Output Interface. The open collector IF
output interfaces are biased through pull-up choke inductors
L1, L2, L4, and L5, with R3 and R6 available for additional
supply bypassing. T1 and T2 are 4:1 impedance transformers
used to provide a single-ended IF output interface with C27
and C28 providing center-tap bypassing. C17, C19, C20, C29,
C30, C31, C32, and C33 ensure an ac-coupled output interface.
Remove R9 and R10 for balanced output operation.
C17, C19, C20, C29 to C33 = 0.001 μF (Size 0402),
C27, C28 = 150 pF (Size 0402),
T1, T2 = TC4-1T+ (Mini-Circuits),
L1, L2, L4, L5 = 330 nH (Size 0805),
R3, R6, R9, R10 = 0 Ω (Size 0402)
R3, R6, R9, R10
C14, C16,
R15, LOSEL
LO Interface. C14 and C16 provide ac coupling for the LOI1 and LOI2 C14, C16 = 10 pF (Size 0402),
local oscillator inputs. LOSEL selects the appropriate LO input for
both mixer cores. R15 provides a pull-down to ensure LOI2 is enabled
when the LOSEL jumper is removed. Jumper can be removed to
allow LOSEL interface to be exercised using external logic generator.
R15 = 10 kΩ (Size 0402),
LOSEL = 2-pin shunt
R19, PWDN
PWDN Interface. When the PWDN 2-pin shunt is inserted, the
ADL5356 is powered down. When R19 is open, it pulls the PWDN
logic low and enables the device. Jumper can be removed to allow
PWDN interface to be excercised using an external logic generator.
Grounding the PWDN pin is allowed during nominal operation but
is not permitted when supply voltages exceed 3.3 V.
R19 = 10 kΩ (Size 0402),
PWDN = 2-pin shunt
R1, R2, R4, R5, L3,
L6, R7, R8, R11 to
Bias Control. R16 and R17 form a voltage divider to provide a 3 V for R1, R4 = 1.3 kΩ (Size 0402),
logic control, bypassed to ground through C34. R7, R8, R11, R12, R13, R2, R5 = 1 kΩ (Size 0402),
R14, R16, R17, C34 and R14 provide resistor programmability of VGS0, VGS1, and VGS2. L3, L6 = 0 Ω (Size 0603),
Typically, these nodes can be hardwired for nominal operation. R12, R13, R14 = open (Size 0402),
Grounding these pins is allowed for nominal operation. R2 and R5 set R7, R8, R11 = 0 Ω (Size 0402),
the bias point for the internal LO buffers. R1 and R4 set the bias point
for the internal IF amplifiers. L3 and L6 are external inductors used to
improve isolation and common-mode rejection.
R16 = 10 kΩ (Size 0402),
R17 = 15 kΩ (Size 0402),
C34 = 1 nF (Size 0402)
Figure 55. Evaluation Board Top Layer
Figure 56. Evaluation Board Bottom Layer
Rev. 0 | Page 22 of 24
ADL5356
OUTLINE DIMENSIONS
6.00
BSC SQ
0.60 MAX
0.60 MAX
PIN 1
INDICATOR
36
28
1
9
27
0.50
BSC
PIN 1
INDICATOR
3.85
3.70 SQ
3.55
TOP
VIEW
5.75
BSC SQ
EXPOSED
PAD
(BOTTOM VIEW)
0.75
0.60
0.50
19
18
10
0.20 MIN
4.00
REF
0.80 MAX
0.65 TYP
12° MAX
1.00
0.85
0.80
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.35
0.28
0.23
SECTION OF THIS DATA SHEET.
SEATING
PLANE
0.20 REF
COMPLIANT TO JEDEC STANDARDS MO-220-VJJD-1
Figure 57. 36-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
6mm × 6 mm Body, Very Thin Quad (CP-36-1)
Dimensions shown in millimeters
ORDERING GUIDE
Model
ADL5356ACPZ-R21
ADL5356ACPZ-R71
ADL5356-EVALZ1
Temperature Range
−40°C to +85°C
−40°C to +85°C
Package Description
Package Option
36-Lead LFCSP_VQ
36-Lead LFCSP_VQ
Evaluation Board
CP-36-1
CP-36-1
1 Z = RoHS Compliant Part.
Rev. 0 | Page 23 of 24
ADL5356
NOTES
©2009 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D07883-0-10/09(0)
Rev. 0 | Page 24 of 24
相关型号:
ADL5358XCPZ-R7
RF/Microwave Mixer, 500 MHz - 1700 MHz RF/MICROWAVE DOUBLE BALANCED MIXER, 6 X 6 MM, MO-220VJJD-1, LFCSP-36
ADI
ADL5358XCPZ-WP
RF/Microwave Mixer, 500 MHz - 1700 MHz RF/MICROWAVE DOUBLE BALANCED MIXER, 6 X 6 MM, MO-220VJJD-1, LFCSP-36
ADI
©2020 ICPDF网 联系我们和版权申明