ADP124 [ADI]
5.5 V Input, 500 mA, Low Quiescent Current, CMOS Linear Regulators; 5.5 V输入500毫安,低静态电流, CMOS线性稳压器型号: | ADP124 |
厂家: | ADI |
描述: | 5.5 V Input, 500 mA, Low Quiescent Current, CMOS Linear Regulators |
文件: | 总20页 (文件大小:678K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
5.5 V Input, 500 mA, Low Quiescent
Current, CMOS Linear Regulators
ADP124/ADP125
TYPICAL APPLICATION CIRCUITS
FEATURES
Input voltage supply range: 2.3 V to 5.5 V
500 mA maximum output current
Fixed and adjustable output voltage versions
1% initial accuracy
Up to 31 fixed-output voltage options available
from 1.75 V to 3.3 V
1
2
3
4
8
7
6
5
VOUT
VIN
V
= 3.3V
V
= 5.5V
OUT
IN
ADP124
VOUT
VIN
C2
C1
VOUT
SENSE
NC
EN
ON
GND
OFF
Adjustable-output voltage range from 0.8 V to 5.0 V
Very low dropout voltage: 130 mV
Low quiescent current: 45 μA
Figure 1. ADP124 with Fixed Output Voltage
V
OUT
= 3.3V
Low shutdown current: <1 μA
1
2
3
4
8
7
6
5
VOUT
VIN
V
= 5.5V
C1
IN
Excellent PSRR performance: 60 dB at 100 kHz
Excellent load/line transient response
Optimized for small 1.0 ꢀF ceramic capacitors
Current limit and thermal overload protection
Logic controlled enable
ADP125
VOUT
VIN
C2
R1
R2
NC
EN
ADJ
ON
GND
OFF
Compact 8-lead exposed paddle MSOP package
Figure 2. ADP 125 with Adjustable Output Voltage
APPLICATIONS
Digital camera and audio devices
Portable and battery-powered equipment
Automatic meter reading (AMR) meters
GPS and location management units
Medical instrumentation
Point of load power
GENERAL DESCRIPTION
The ADP124/ADP125 are low quiescent current, low dropout
linear regulators. They are designed to operate from an input
voltage between 2.3 V and 5.5 V and to provide up to 500 mA of
output current. The low 130 mV dropout voltage at a 500 mA
load improves efficiency and allows operation over a wide input
voltage range.
The ADP124/ADP125 are specifically designed for stable operation
with tiny 1 ꢀF ceramic input and output capacitors to meet the
requirements of high performance, space constrained applications.
The ADP124/ADP125 have an internal soft start that gives a
constant start-up time of 350 ꢀs. Short-circuit protection and
thermal overload protection circuits prevent damage in adverse
conditions. The ADP124/ADP125 are available in an 8-lead
exposed paddle MSOP package. When compared with the
standard MSOP package, the exposed paddle MSOP package
has lower thermal resistance (θJA). The lower thermal resistance
package allows the ADP124/ADP125 to meet the needs of a
variety of portable applications while minimizing the rise in
junction temperature.
The low 210 μA of quiescent current with a 500 mA load makes the
ADP124/ADP125 ideal for battery-operated portable equipment.
The ADP124 is capable of 31 fixed-output voltages from 1.75 V
to 3.3 V. The ADP125 is the adjustable version of the device and
allows the output voltage to be set between 0.8 V and 5.0 V by
an external voltage divider.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
©2009 Analog Devices, Inc. All rights reserved.
ADP124/ADP125
TABLE OF CONTENTS
Features .............................................................................................. 1
Typical Performance Characteristics ..............................................7
Theory of Operation ...................................................................... 11
Applications Information.............................................................. 12
Capacitor Selection .................................................................... 12
Undervoltage Lockout ............................................................... 13
Enable Feature ............................................................................ 13
Current Limit and Thermal Overload Protection ................. 14
Thermal Considerations............................................................ 14
Junction Temperature Calculations......................................... 15
Printed Circuit Board Layout Considerations ....................... 16
Outline Dimensions....................................................................... 17
Ordering Guide .......................................................................... 17
Applications....................................................................................... 1
Typical Application Circuits............................................................ 1
General Description......................................................................... 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
Recommended Capacitor Specifications................................... 4
Absolute Maximum Ratings............................................................ 5
Thermal Data................................................................................ 5
Thermal Resistance ...................................................................... 5
ESD Caution.................................................................................. 5
Pin Configurations and Function Descriptions ........................... 6
REVISION HISTORY
12/09—Revision 0: Initial Version
Rev. 0 | Page 2 of 20
ADP124/ADP125
SPECIFICATIONS
Unless otherwise noted, VIN = (VOUT + 0.5 V) or 2.3 V, whichever is greater; ADJ connected to VOUT; IOUT = 10 mA; CIN = 1.0 μF;
COUT = 1.0 μF; TA = 25°C.
Table 1.
Parameter
Symbol
VIN
Test Conditions
Min
Typ
45
Max
Unit
V
INPUT VOLTAGE RANGE
OPERATING SUPPLY CURRENT1
2.3
5.5
IGND
IOUT = 0 μA
IOUT = 0 μA, TJ = −40°C to +125°C
IOUT = 1 mA
IOUT = 1 mA, TJ = −40°C to +125°C
IOUT = 250 mA
IOUT = 250 mA, TJ = −40°C to +125°C
IOUT = 500 mA
IOUT = 500 mA, TJ = −40°C to +125°C
EN = GND
EN = GND, TJ = −40°C to +125°C
μA
μA
μA
μA
μA
μA
μA
μA
μA
μA
105
120
210
280
1
60
160
210
0.1
SHUTDOWN CURRENT
ISD
OUTPUT VOLTAGE ACCURACY2
Fixed Output
VOUT
IOUT = 10 mA
100 μA < IOUT < 500 mA, VIN = (VOUT + 0.5 V) to 5.5 V,
TJ = −40°C to +125°C
−1
−2
+1
+1.5
%
%
Adjustable Output
IOUT = 10 mA
100 μA < IOUT < 500 mA, VIN = 2.3 V to 5.5 V,
TJ = −40°C to +125°C
0.495 0.500
0.485 0.500
0.505
0.515
V
V
LINE REGULATION
LOAD REGULATION3
∆VOUT/∆VIN
VIN = VIN = 2.3 V to 5.5 V, TJ = −40°C to +125°C
−0.05
+0.05 %/V
%/mA
0.001 %/mA
nA
∆VOUT/∆IOUT IOUT = 1 mA to 500 mA
IOUT = 1 mA to 500 mA, TJ = −40°C to +125°C
0.0005
ADJ INPUT BIAS CURRENT
DROPOUT VOLTAGE4
ADJI-BIAS
VDROPOUT
2.3 V ≤ VIN ≤ 5.5 V, ADJ connected to VOUT
15
3
IOUT = 10 mA, VOUT > 2.3 V
mV
IOUT = 10 mA, TJ = −40°C to +125°C
IOUT = 250 mA, VOUT > 2.3 V
IOUT = 250 mA, TJ = −40°C to +125°C
IOUT = 500 mA, VOUT > 2.3V
IOUT = 500 mA, TJ = −40°C to +125°C
VOUT = 3.0 V
5
mV
mV
mV
mV
mV
μs
65
120
230
1000
130
START-UP TIME5
CURRENT LIMIT THRESHOLD6
tSTART-UP
ILIMIT
350
550
1.2
750
mA
THERMAL SHUTDOWN
Thermal Shutdown Threshold
Thermal Shutdown Hysteresis
TSSD
TJ rising
150
15
°C
°C
TSSD-HYS
EN INPUT
EN Input Logic High
EN Input Logic Low
EN Input Leakage Current
VIH
VIL
VI-LEAKAGE
2.3 V ≤ VIN ≤ 5.5 V
2.3 V ≤ VIN ≤ 5.5 V
EN = VIN or GND
EN = VIN or GND, TJ = −40°C to +125°C
V
V
μA
μA
0.4
1
0.1
UNDERVOLTAGE LOCKOUT
Input Voltage Rising
Input Voltage Falling
Hysteresis
UVLO
UVLORISE
UVLOFALL
UVLOHYS
TJ = −40°C to +125°C
TJ = −40°C to +125°C
TA = 25°C
2.1
V
V
mV
1.5
125
Rev. 0 | Page 3 of 20
ADP124/ADP125
Parameter
Symbol
Test Conditions
Min
Typ
25
35
45
55
65
60
Max
Unit
OUTPUT NOISE
OUTNOISE
10 Hz to 100 kHz, VIN = 5.5 V, VOUT = 1.2 V
10 Hz to 100 kHz, VIN = 5.5 V, VOUT = 1.8 V
10 Hz to 100 kHz, VIN = 5.5 V, VOUT = 2.5 V
10 Hz to 100 kHz, VIN = 5.5 V, VOUT = 3.3 V
10 Hz to 100 kHz, VIN = 5.5 V, VOUT = 4.2V
10 kHz to 100 kHz, VOUT = 1.8 V, 2.5 V, 3.3 V
μV rms
μV rms
μV rms
μV rms
μV rms
dB
POWER SUPPLY REJECTION RATIO
(VIN = VOUT +1V)
PSRR
1 The current from the external resistor divider network in the case of adjustable voltage output (as with the ADP125) should be subtracted from the ground current measured.
2 Accuracy when VOUT is connected directly to ADJ. When VOUT voltage is set by external feedback resistors, absolute accuracy in adjust mode depends on the tolerances of
the resistors used.
3 Based on an endpoint calculation using 1 mA and 500 mA loads.
4 Dropout voltage is defined as the input-to-output voltage differential when the input voltage is set to the nominal output voltage. This applies only for output voltages
greater than 2.3V.
5 Start-up time is defined as the time between the rising edge of EN to VOUT being at 90% of its nominal value.
6 Current limit threshold is defined as the current at which the output voltage drops to 90% of the specified typical value. For example, the current limit for a 3.3 V
output voltage is defined as the current that causes the output voltage to drop to 90% of 3.3V, or 2.97 V.
RECOMMENDED CAPACITOR SPECIFICATIONS
Table 2.
Parameter
Symbol
Test Conditions
Min
Typ
Max
Unit
Minimum Input and Output
Capacitance1
CAPMIN
TA = −40°C to +125°C
0.70
μF
Capacitor ESR
RESR
TA = −40°C to +125°C
0.001
1
Ω
1 The minimum input and output capacitance should be greater than 0.70 μF over the full range of operating conditions. The full range of operating conditions in the
application must be considered during device selection to ensure that the minimum capacitance specification is met. X7R and X5R type capacitors are recommended;
Y5V and Z5U capacitors are not recommended for use with this LDO.
Rev. 0 | Page 4 of 20
ADP124/ADP125
ABSOLUTE MAXIMUM RATINGS
application and board layout. In applications in which high maxi-
mum power dissipation exists, close attention to thermal board
design is required. The value of θJA may vary, depending on PCB
material, layout, and environmental conditions. The specified
values of θJA are based on a 4-layer, 4 inch × 3 inch circuit board.
Refer to JESD 51-7 for detailed information on the board
construction
Table 3.
Parameter
Rating
VIN to GND
ADJ to GND
−0.3 V to +6.5V
−0.3 V to +4 V
EN to GND
VOUT to GND
−0.3 V to +6.5V
−0.3 V to VIN
Storage Temperature Range
Operating Ambient Temperature Range
Operating Junction Temperature Range
Soldering Conditions
−65°C to +150°C
−40°C to +85°C
−40°C to +125°C
JEDEC J-STD-020
ΨJB is the junction-to-board thermal characterization parameter
and is measured in °C/W. The ΨJB of the package is based on
modeling and calculation using a 4-layer board. The Guidelines for
Reporting and Using Package Thermal Information: JESD51-12
states that thermal characterization parameters are not the same
as thermal resistances. ΨJB measures the component power flowing
through multiple thermal paths rather than a single path as in
thermal resistance, θJB. Therefore, ΨJB thermal paths include
convection from the top of the package as well as radiation from
the package—factors that make ΨJB more useful in real-world
applications. Maximum junction temperature (TJ) is calculated
from the board temperature (TB) and power dissipation (PD)
using the formula
Stresses above those listed under Absolute Maximum Ratings may
cause permanent damage to the device. This is a stress rating
only; functional operation of the device at these or any other
conditions above those indicated in the operational section of
this specification is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device reliability.
THERMAL DATA
Absolute maximum ratings apply individually only, not in
combination. The ADP124/ADP125 can be damaged when the
junction temperature limits are exceeded. Monitoring ambient
temperature does not guarantee that TJ will remain within the
specified temperature limits. In applications with high power
dissipation and poor thermal resistance, the maximum ambient
temperature may have to be limited.
TJ = TB + (PD × ΨJB)
Refer to JESD51-8 and JESD51-12 for more detailed information
about ΨJB.
THERMAL RESISTANCE
θJA and ΨJB are specified for the worst-case conditions, that is, a
device soldered in a circuit board for surface-mount packages.
In applications with moderate power dissipation and low PCB
thermal resistance, the maximum ambient temperature can
exceed the maximum limit as long as the junction temperature
is within specification limits. The junction temperature (TJ) of
the device is dependent on the ambient temperature (TA), the
power dissipation of the device (PD), and the junction-to-ambient
thermal resistance of the package (θJA).
Table 4. Thermal Resistance
Package Type
θJA
ΨJB
Unit
8-Lead MSOP
102.8
31.8
°C/W
ESD CAUTION
Maximum junction temperature (TJ) is calculated from the
ambient temperature (TA) and power dissipation (PD) using the
formula
TJ = TA + (PD × θJA)
The junction-to-ambient thermal resistance (θJA) of the package
is based on modeling and calculation using a 4-layer board. The
junction-to-ambient thermal resistance is highly dependent on the
Rev. 0 | Page 5 of 20
ADP124/ADP125
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
VOUT
VOUT
1
2
3
4
8
7
6
5
VIN
VIN
NC
EN
VOUT
VOUT
ADJ
1
2
3
4
8
7
6
5
VIN
VIN
NC
EN
ADP124
ADP125
TOP VIEW
TOP VIEW
VOUT SENSE
GND
(Not to Scale)
(Not to Scale)
GND
NC = NO CONNECT
NC = NO CONNECT
Figure 3. ADP124 Fixed Output Pin Configuration
Figure 4. ADP125 Adjustable Output Pin Configuration
Table 5. Pin Function Descriptions
Mnemonic
ADP125
Pin No. ADP124
Description
1
2
3
VOUT
VOUT
VOUT SENSE N/A
VOUT
VOUT
Regulated Output Voltage. Bypass VOUT to GND with a 1 μF or greater capacitor.
Regulated Output Voltage. Bypass VOUT to GND with a 1 μF or greater capacitor.
Feedback Node for the Error Amplifier. Connect to VOUT.
N/A
ADJ
Feedback Node for the Error Amplifier. Connect the midpoint of an external divider from
VOUT to GND to this pin to set the output voltage.
4
5
GND
EN
GND
EN
Ground.
Enable Input. Drive EN high to turn on the regulator; drive EN low to turn off the regulator.
For automatic startup, connect EN to VIN.
6
7
8
NC
VIN
VIN
EP
NC
VIN
VIN
EP
No Connect. This pin is not connected internally.
Regulator Input Supply. Bypass VIN to GND with a 1 μF or greater capacitor.
Regulator Input Supply. Bypass VIN to GND with a 1 μF or greater capacitor.
The exposed pad must be connected to ground.
Rev. 0 | Page 6 of 20
ADP124/ADP125
TYPICAL PERFORMANCE CHARACTERISTICS
VIN = 3.8 V, VOUT = 3.3V, IOUT = 10 mA, CIN = 1.0 ꢀF, COUT = 1.0 ꢀF, TA = 25°C, unless otherwise noted.
3.310
3.305
3.300
3.295
3.290
3.285
3.280
3.275
3.270
300
250
200
150
100
50
I
I
= 500mA
= 300mA
OUT
OUT
I
I
I
I
I
I
= 100µA
= 1mA
= 10mA
= 100mA
= 300mA
= 500mA
OUT
OUT
OUT
OUT
OUT
OUT
I
I
= 100mA
= 10mA
OUT
OUT
I
= 100µA
OUT
I
= 1mA
OUT
+25
–40
–5
+85
+125
–40
–5
+25
+85
+125
JUNCTION TEMPERATURE (°C)
JUNCTION TEMPERATURE (°C)
Figure 5. Output Voltage vs. Junction Temperature
Figure 8. Ground Current vs. Junction Temperature
3.309
3.308
3.307
3.306
3.305
3.304
3.303
250
200
150
100
50
0
0.1
1
10
(mA)
100
1000
0.1
1
10
(mA)
100
1000
I
I
OUT
LOAD
Figure 9. Ground Current vs. Load Current
Figure 6. Output Voltage vs. Load Current
3.310
3.308
3.306
3.304
3.302
3.300
3.298
3.296
3.294
3.292
250
230
210
190
170
150
130
110
90
I
I
= 500mA
= 300mA
OUT
OUT
I
I
I
I
I
I
= 100µA
= 1mA
= 10mA
= 100mA
= 300mA
= 500mA
OUT
OUT
OUT
OUT
OUT
OUT
I
I
= 100mA
= 10mA
OUT
I
= 1mA
OUT
I
= 100µA
5.00
OUT
OUT
70
50
3.50
3.50
4.00
4.50
(V)
5.00
5.50
4.00
4.50
(V)
5.50
V
V
IN
IN
Figure 7. Output Voltage vs. Input Voltage
Figure 10. Ground Current vs. Input Voltage
Rev. 0 | Page 7 of 20
ADP124/ADP125
0.7
3.35
3.30
3.25
3.20
3.15
3.10
3.05
3.00
2.95
I
I
I
I
= 10mA
OUT
OUT
OUT
OUT
0.6
= 100mA
= 300mA
= 500mA
0.5
0.4
0.3
0.2
0.1
0
V
V
V
V
V
V
V
= 5.50
= 5.40
= 5.20
= 5.00
= 4.40
= 4.20
= 3.80
IN
IN
IN
IN
IN
IN
IN
–50
–25
0
25
50
75
100
125
3.00
3.10
3.20
3.30
(V)
3.40
3.50
3.60
TEMPERATURE (°C)
V
IN
Figure 11. Shutdown Current vs. Temperature at Various Input Voltages
Figure 14. Output Voltage vs. Input Voltage (in Dropout)
120
100
80
60
40
20
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
I
I
I
I
I
I
= 100µA
= 1mA
= 10mA
= 100mA
= 300mA
= 500mA
OUT
OUT
OUT
OUT
OUT
OUT
V
V
C
= V
+1V
= 50mV
IN
RIPPLE
= C
OUT
= 1µF
IN
OUT
1
10
100
1000
10
100
1k
10k
100k
1M
10M
I
(mA)
OUT
FREQUENCY (Hz)
Figure 12. Dropout Voltage vs. Load Current
Figure 15. Power Supply Rejection Ratio vs. Frequency, VOUT = 2.8 V, VIN = 3.8 V
450
400
350
300
250
200
150
100
50
–10
–20
I
I
I
I
I
I
= 100µA
= 1mA
= 10mA
= 100mA
= 300mA
= 500mA
OUT
OUT
OUT
OUT
OUT
OUT
–30
–40
–50
–60
–70
–80
–90
–100
I
I
I
I
= 10mA
OUT
OUT
OUT
OUT
= 100mA
= 300mA
= 500mA
V
V
C
= V
+1V
= 50mV
IN
RIPPLE
= C
OUT
= 1µF
IN
OUT
0
3.00
3.10
3.20
3.30
3.40
(V)
3.50
3.60
3.70
10
100
1k
10k
100k
1M
10M
V
FREQUENCY (Hz)
IN
Figure 13. Ground Current vs. Input Voltage (in Dropout)
Figure 16. Power Supply Rejection Ratio vs. Frequency, VOUT = 3.3 V, VIN = 4.3 V
Rev. 0 | Page 8 of 20
ADP124/ADP125
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
5
4
3
2
1
0
I
I
I
I
I
I
= 100µA
= 1mA
= 10mA
= 100mA
= 300mA
= 500mA
OUT
OUT
OUT
OUT
OUT
OUT
V
= 4.2V
OUT
V
= 3.3V
OUT
V
= 2.8V
OUT
V
V
C
= V
+ 1V
= 50mV
IN
RIPPLE
= C
OUT
= 1µF
IN
OUT
10
100
1k
FREQUENCY (Hz)
10k
100k
10
100
1k
10k
100k
1M
10M
FREQUENCY (Hz)
Figure 17. Power Supply Rejection Ratio vs. Frequency, VOUT = 4.2 V, VIN = 5.2 V
Figure 20. Output Noise Spectrum, VIN = 5 V
–10
70
65
60
55
50
45
40
35
30
25
20
V
V
V
V
V
V
= 2.8V, I
= 3.3V, I
= 4.2V, I
= 2.8V, I
= 3.3V, I
= 4.2V, I
= 10mA
= 10mA
= 10mA
= 500mA
= 500mA
= 500mA
V
V
= 4.2V
= 3.3V
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
–20
–30
–40
–50
–60
–70
–80
–90
–100
OUT
V
= 2.8V
OUT
V
V
C
= V
+ 1V
= 50mV
IN
RIPPLE
= C
OUT
= 1µF
IN
OUT
10
100
1k
10k
100k
1M
10M
0.001
0.01
0.1
1
10
100
1k
I
LOAD
(mA)
FREQUENCY (Hz)
Figure 18. Power Supply Rejection Ratio vs. Frequency,
Various Output Voltages and Load Currents
Figure 21. Output Noise vs. Load Current and Output Voltage, VIN = 5 V
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
I
OUT
V
V
V
V
= 3.1V, I
= 3.3V, I
= 3.8V, I
= 4.8V, I
= 10mA
= 10mA
= 10mA
= 10mA
IN
IN
IN
IN
OUT
OUT
OUT
OUT
1mA TO 500mA LOAD STEP
1
V
OUT
2
V
V
V
V
= 3.1V, I
= 3.3V, I
= 3.8V, I
= 4.8V, I
= 500mA
= 500mA
= 500mA
= 500mA
IN
IN
IN
IN
OUT
OUT
OUT
OUT
V
V
= 4V
= 3.3V
IN
OUT
CH1 500mA Ω B CH2 50.0mV
M40.0µs
9.800%
A CH1 200mA
B
W
W
10
100
1k
10k
100k
1M
10M
T
FREQUENCY (Hz)
Figure 19. Power Supply Rejection Ratio vs. Headroom Voltage (VIN − VOUT),
VOUT = 2.8 V
Figure 22. Load Transient Response, COUT = 1 μF
Rev. 0 | Page 9 of 20
ADP124/ADP125
I
OUT
1mA TO 500mA LOAD STEP
V
IN
4V TO 4.5V VOLTAGE STEP
1
V
OUT
2
1
2
V
OUT
V
V
= 4V
= 3.3V
IN
OUT
B
B
W
CH1 500mA Ω B CH2 50.0mV
M40.0µs
9.800%
A
CH1 200mA
CH1 1.00V B
CH2 2.00mV
M10.0µs
T 9.800%
A CH3 200mA
W
W
W
T
Figure 23. Load Transient Response, COUT = 4.7 μF
Figure 25. Line Transient Response, Load Current = 500 mA
V
IN
4V TO 4.5V VOLTAGE STEP
V
OUT
2
1
B
CH1 1.00V B
CH2 2.00mV
M10.0µs
9.600%
A CH3 2.36V
W
W
T
Figure 24. Line Transient Response, Load Current = 1 mA
Rev. 0 | Page 10 of 20
ADP124/ADP125
THEORY OF OPERATION
The ADP124/ADP125 are low quiescent current, low dropout
linear regulators that operate from 2.3 V to 5.5 V and can provide
up to 500 mA of output current. Drawing a low 210 ꢀA of quies-
cent current (typical) at full load makes the ADP124/ADP125
ideal for battery-operated portable equipment. Shutdown current
consumption is typically 100 nA.
The ADP124/ADP125 use the EN pin to enable and disable the
VOUT pin under normal operating conditions. When EN is high,
VOUT turns on; when EN is low, VOUT turns off. For automatic
startup, EN can be tied to VIN.
ADP124
VIN
VOUT
Optimized for use with small 1 ꢀF ceramic capacitors, the
ADP124/ADP125 provide excellent transient performance.
VOUT SENSE
SHORT CIRCUIT,
UVLO, AND
THERMAL
R1
R2
Internally, the ADP124/ADP125 consist of a reference, an error
amplifier, a feedback voltage divider, and a PMOS pass transistor.
Output current is delivered via the PMOS pass device, which is
controlled by the error amplifier. The error amplifier compares
the reference voltage with the feedback voltage from the output
and amplifies the difference. If the feedback voltage is lower than
the reference voltage, the gate of the PMOS device is pulled lower,
allowing more current to pass and increasing the output voltage.
If the feedback voltage is higher than the reference voltage, the
gate of the PMOS device is pulled higher, allowing less current
to pass and decreasing the output voltage.
GND
PROTECT
EN
SHUTDOWN
0.5V REFERENCE
NOTES
1. R1 AND R2 ARE INTERNAL RESISTORS, AVAILABLE ON
THE ADP124 ONLY.
Figure 26. ADP124 Internal Block Diagram (Fixed Output)
ADP125
The adjustable ADP125 has an output voltage range of 0.8 V to
5.0 V. The output voltage is set by the ratio of two external resistors,
as shown in Figure 2. The device servos the output to maintain
the voltage at the ADJ pin at 0.5 V referenced to ground. The
current in R1 is then equal to 0.5 V/R2 and the current in R1 is
the current in R2 plus the ADJ pin bias current. The ADJ pin
bias current, 15 nA at 25°C, flows through R1 into the ADJ pin.
VIN
VOUT
SHORT CIRCUIT,
UVLO, AND
THERMAL
GND
EN
PROTECT
ADJ
The output voltage can be calculated using the equation:
SHUTDOWN
0.5V REFERENCE
V
OUT = 0.5 V(1 + R1/R2) + (ADJI-BIAS)(R1)
The value of R1 should be less than 200 kΩ to minimize errors
in the output voltage caused by the ADJ pin bias current. For
example, when R1 and R2 each equal 200 kΩ, the output voltage
is 1.0 V. The output voltage error introduced by the ADJ pin
bias current is 3 mV or 0.3%, assuming a typical ADJ pin bias
current of 15 nA at 25°C.
Figure 27. ADP125 Internal Block Diagram (Adjustable Output)
Note that in shutdown, the output is turned off and the divider
current is 0.
Rev. 0 | Page 11 of 20
ADP124/ADP125
APPLICATIONS INFORMATION
CAPACITOR SELECTION
Output Capacitor
Input Bypass Capacitor
Connecting a 1 ꢀF capacitor from VIN to GND reduces the circuit
sensitivity to the printed circuit board (PCB) layout, especially
when a long input trace or high source impedance is encountered.
If greater than 1 ꢀF of output capacitance is required, the input
capacitor should be increased to match it.
The ADP124/ADP125 are designed for operation with small,
space-saving ceramic capacitors, but these devices can function
with most commonly used capacitors as long as care is taken to
ensure an appropriate effective series resistance (ESR) value. The
ESR of the output capacitor affects the stability of the LDO control
loop. A minimum of 0.70 ꢀF capacitance with an ESR of 1 ꢁ or
less is recommended to ensure stability of the ADP124/ADP125.
The transient response to changes in load current is also affected by
the output capacitance. Using a larger value of output capacitance
improves the transient response of the ADP124/ADP125 to
dynamic changes in load current. Figure 28 and Figure 29 show
the transient responses for output capacitance values of 1 ꢀF and
4.7ꢀF, respectively.
Input and Output Capacitor Properties
Any good quality ceramic capacitors can be used with the
ADP124/ADP125, as long as the capacitor meets the minimum
capacitance and maximum ESR requirements. Ceramic capacitors
are manufactured with a variety of dielectrics, each with different
behavior over temperature and applied voltage. Capacitors must
have an adequate dielectric to ensure the minimum capacitance
over the necessary temperature range and dc bias conditions.
Using an X5R or X7R dielectric with a voltage rating of 6.3 V or
10 V is recommended. However, using Y5V and Z5U dielectrics
are not recommended for any LDO, due to their poor temperature
and dc bias characteristics.
I
OUT
1mA TO 500mA LOAD STEP
1
Figure 30 depicts the capacitance vs. capacitor voltage bias charac-
teristics of an 0402, 1 ꢀF, 10 V X5R capacitor. The voltage stability
of a capacitor is strongly influenced by the capacitor size and the
voltage rating. In general, a capacitor in a larger package or of a
higher voltage rating exhibits better stability. The temperature
variation of the X5R dielectric is about 15% over the −40°C to
+85°C temperature range and is not a function of package or
voltage rating.
2
V
OUT
V
V
= 4V
= 3.3V
IN
OUT
1.10
B
CH1 500mA Ω B CH2 50.0mV
M400ns A CH1 200mA
13.20%
W
W
T
1.05
1.00
0.95
0.90
0.85
0.80
0.75
0.70
Figure 28. Output Transient Response, COUT = 1 ꢀF
I
OUT
1mA TO 500mA LOAD STEP
1
2
V
OUT
0
1
2
3
4
5
6
7
BIAS VOLTAGE (V)
V
V
= 4V
= 3.3V
IN
OUT
Figure 30. Capacitance vs. Capacitor Voltage Bias Characteristics
Equation 1 can be used to determine the worst-case capacitance,
accounting for capacitor variation over temperature, component
tolerance, and voltage.
B
CH1 500mA Ω B CH2 50.0mV
M400ns A CH1 200mA
13.60%
W
W
T
Figure 29. Output Transient Response, COUT = 4.7 ꢀF
CEFF = C × (1 − TEMPCO) × (1 − TOL)
(1)
where:
CEFF is the effective capacitance at the operating voltage.
C is the rated capacitance value.
TEMPCO is the worst-case capacitor temperature coefficient.
TOL is the worst-case component tolerance.
Rev. 0 | Page 12 of 20
ADP124/ADP125
In this example, the worst-case temperature coefficient (TEMPCO)
over −40°C to +85°C is assumed to be 15% for an X5R dielectric.
The tolerance of the capacitor (TOL) is assumed to be 10%, and
C is 0.94 μF at 4.2 V from the graph in Figure 30.
The active and inactive thresholds of the EN pin are derived from
the VIN voltage. Therefore, these thresholds vary as the input
voltage changes. Figure 32 shows typical EN active and inactive
thresholds when the VIN voltage varies from 2.3 V to 5.5 V.
1.05
Substituting these values in Equation 1 yields
1.00
0.95
C
EFF = 0.94 μF × (1 − 0.15) × (1 − 0.1) = 0.719 μF
Therefore, the capacitor chosen in this example meets the
minimum capacitance requirement of the LDO over tem-
perature and tolerance at the chosen output voltage.
RISING
0.90
0.85
0.80
To guarantee the performance of the ADP124/ADP125, it is
imperative that the effects of dc bias, temperature, and tolerances
on the behavior of the capacitors are evaluated for each application.
FALLING
0.75
0.70
0.65
UNDERVOLTAGE LOCKOUT
The ADP124/ADP125 have an internal undervoltage lockout
circuit that disables all inputs and the output when the input
voltage is less than approximately 2 V. This ensures that the
ADP124/ADP125 inputs and the output behave in a predictable
manner during power-up.
0.60
2.2
2.7
3.2
3.7
(V)
4.2
4.7
5.2
V
IN
Figure 32. Typical EN Pin Thresholds vs. Input Voltage
The ADP124/ADP125 use an internal soft start to limit the in-
rush current when the output is enabled. The start-up time for
the 2.8 V option is approximately 350 ꢀs from the time the EN
active threshold is crossed to when the output reaches 90% of its
final value. As shown in Figure 33, the start-up time is dependent
on the output voltage setting and increases slightly as the output
voltage increases.
ENABLE FEATURE
The ADP124/ADP125 uses the EN pin to enable and disable the
VOUT pin under normal operating conditions. As shown in
Figure 31, when a rising voltage on EN crosses the active threshold,
VOUT turns on. Conversely, when a falling voltage on EN crosses
the inactive threshold, VOUT turns off.
3.5
V
V
= 5V
IN
3.0
2.5
2.0
1.5
1.0
0.5
0
= 4.2V
= 3.3V
OUT
OUT
V
V
= 2.8V
OUT
1
2
B
CH1 1.00V CH2 1.00V
M100µs
296.800µs
A
CH1
2.00V
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
W
T
V
EN
Figure 33. Typical Start-Up Time
Figure 31. Typical EN Pin Operation
As shown in Figure 31, the EN pin has built-in hysteresis. This
prevents on/off oscillations that may occur due to noise on the
EN pin as it passes through the threshold points.
Rev. 0 | Page 13 of 20
ADP124/ADP125
The junction temperature of the ADP124/ADP125 can be
calculated from the following equation:
CURRENT LIMIT AND THERMAL OVERLOAD
PROTECTION
TJ = TA + (PD × θJA)
(2)
(3)
The ADP124/ADP125 are protected from damage due to excessive
power dissipation by current and thermal overload protection
circuits. The ADP124/ADP125 are designed to limit the current
when the output load reaches 750 mA (typical). When the output
load exceeds 750 mA, the output voltage is reduced to maintain
a constant current limit.
where:
TA is the ambient temperature.
PD is the power dissipation in the die, given by
PD = [(VIN − VOUT) × ILOAD] + (VIN × IGND
)
where:
LOAD is the load current.
GND is the ground current.
Thermal overload protection is included, which limits the junction
temperature to a maximum of 150°C typical. Under extreme con-
ditions (that is, high ambient temperature and power dissipation),
when the junction temperature starts to rise above 150°C, the
output is turned off, reducing output current to zero. When the
junction temperature cools to less than 135°C, the output is turned
on again and the output current is restored to its nominal value.
I
I
V
IN and VOUT are input and output voltages, respectively.
The power dissipation due to ground current is quite small and
can be ignored. Therefore, the junction temperature equation
can be simplified as follows:
TJ = TA + {[(VIN − VOUT) × ILOAD] × θJA}
(4)
Consider the case where a hard short from VOUT to GND occurs.
At first, the ADP124/ADP125 limit the current so that only 750 mA
is conducted into the short. If self-heating causes the junction
temperature to rise above 150°C, thermal shutdown activates,
turning off the output and reducing the output current to zero.
When the junction temperature cools to less than 135°C, the
output turns on and conducts 750 mA into the short, again
causing the junction temperature to rise above 150°C. This
thermal oscillation between 135°C and 150°C results in a current
oscillation between 750 mA and 0 mA that continues as long as
the short remains at the output.
As shown in Equation 4, for a given ambient temperature, input-
to-output voltage differential, and continuous load current, there
exists a minimum copper size requirement for the PCB to ensure
that the junction temperature does not rise above 125°C. Figure 34
through Figure 40 show junction temperature calculations for
different ambient temperatures, load currents, VIN to VOUT
differentials, and areas of PCB copper.
In cases where the board temperature is known, the thermal
characterization parameter, ΨJB, can be used to estimate the jun-
ction temperature rise. The maximum junction temperature (TJ) is
calculated from the board temperature (TB) and power dissipation
(PD) using the formula
Current and thermal limit protections are intended to protect the
device from damage due to accidental overload conditions. For
reliable operation, the device power dissipation must be externally
limited so that the junction temperature does not exceed 125°C.
TJ = TB + (PD × ΨJB)
(5)
THERMAL CONSIDERATIONS
To guarantee reliable operation, the junction temperature of the
ADP124/ADP125 must not exceed 125°C. To ensure that the
junction temperature is less than this maximum value, the user
needs to be aware of the parameters that contribute to junction
temperature changes. These parameters include ambient tem-
perature, power dissipation in the power device, and thermal
resistances between the junction and ambient air (θJA). The value
of θJA is dependent on the package assembly compounds used
and the amount of copper to which the GND pins of the package
are soldered on the PCB. Table 6 shows typical θJA values of the
8-lead MSOP package for various PCB copper sizes.
Table 6. Typical θJA Values for Specified PCB Copper Sizes
Copper Size (mm2)
θJA (°C/W)
102.8
75.5
42.5
34.7
40
100
500
1000
6400
26.1
The typical ΨJB value is 31.7°C/W.
Rev. 0 | Page 14 of 20
ADP124/ADP125
JUNCTION TEMPERATURE CALCULATIONS
140
140
120
100
80
T
MAX
T MAX
J
J
120
100
80
60
40
20
0
I
= 150mA
LOAD
I
= 100mA
LOAD
I
=
500mA
LOAD
I
= 400mA
LOAD
I
= 75mA
LOAD
I
= 300mA
LOAD
I
= 200mA
LOAD
60
I
= 10mA
LOAD
I
= 50mA
40
LOAD
I
= 1mA
LOAD
I
=
25mA
LOAD
20
I
= 100mA
I
=
1mA
I
= 10mA
LOAD
LOAD
LOAD
0
0.5
1.0
1.5
2.0
2.5
– V
3.0
(V)
3.5
4.0
4.5
4.5
4.5
0.5
1.0
1.5
2.0
2.5
– V
3.0
(V)
3.5
4.0
4.5
V
V
IN
OUT
IN
OUT
Figure 34. Junction Temperature vs. Power Dissipation,
1000 mm2 of PCB Copper, TA = 25°C
Figure 37. Junction Temperature vs. Power Dissipation,
1000 mm2 of PCB Copper, TA = 50°C
140
120
100
80
140
120
100
80
T
MAX
T
MAX
J
J
I
= 500mA
I
=
500mA
LOAD
LOAD
I
= 400mA
LOAD
I
= 400mA
LOAD
I
= 300mA
LOAD
I
=
300mA
LOAD
I
= 200mA
LOAD
60
60
I
= 10mA
LOAD
I
LOAD
= 200mA
40
40
I
=
100mA
I
=
1mA
LOAD
LOAD
I
=
10mA
1mA
LOAD
20
20
I
= 100mA
LOAD
2.5
I
=
LOAD
0
0.5
0
0.5
1.0
1.5
2.0
3.0
(V)
3.5
4.0
1.0
1.5
2.0
2.5
3.0
(V)
3.5
4.0
4.5
V
– V
V
– V
IN OUT
IN
OUT
Figure 35. Junction Temperature vs. Power Dissipation,
500 mm2 of PCB Copper, TA = 25°C
Figure 38. Junction Temperature vs. Power Dissipation,
500 mm2 of PCB Copper, TA = 50°C
140
120
100
80
140
120
100
80
I
= 300mA
LOAD
T
MAX
T
MAX
J
J
I
=
500mA
LOAD
I
= 300mA
LOAD
I
= 400mA
LOAD
I
I
= 200mA
= 100mA
LOAD
I
= 200mA
LOAD
LOAD
60
60
I
I
= 10mA
= 1mA
LOAD
I
= 100mA
LOAD
LOAD
40
40
I
= 500mA
LOAD
I
= 400mA
I
=
=
10mA
1mA
LOAD
LOAD
LOAD
20
20
I
0
0.5
0
0.5
1.0
1.5
2.0
2.5
– V
3.0
3.5
4.0
1.0
1.5
2.0
2.5
– V
3.0
(V)
3.5
4.0
4.5
V
(V)
V
IN
IN
OUT
OUT
Figure 36. Junction Temperature vs. Power Dissipation,
40 mm2 of PCB Copper, TA = 25°C
Figure 39. Junction Temperature vs. Power Dissipation,
40 mm2 of PCB Copper, TA = 50°C
Rev. 0 | Page 15 of 20
ADP124/ADP125
140
T
MAX
J
120
100
80
60
40
20
0
I
=
300mA
LOAD
I
=
400mA
100mA
I
= 500mA
LOAD
LOAD
I
= 200mA
I
=
LOAD
LOAD
I
= 1mA
LOAD
I
=
10mA
LOAD
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
V
– V
(V)
OUT
IN
Figure 40. Junction Temperature vs. Power Dissipation,
40 mm2 of PCB Copper at Board Temperature = 85°C
PRINTED CIRCUIT BOARD LAYOUT
CONSIDERATIONS
Heat dissipation from the package can be improved by increasing
the amount of copper attached to the pins of the ADP124/ADP125.
However, as shown in Table 6, a point of diminishing returns
eventually is reached, beyond which an increase in the copper
size does not yield significant heat dissipation benefits.
Figure 41. Example ADP124 PCB Layout
The input capacitor should be placed as close as possible to the
VIN and GND pins, and the output capacitor should be placed
as close as possible to the VOUT and GND pins. Use of 0402 or
0603 size capacitors and resistors achieves the smallest possible
footprint solution on boards where the area is limited.
Figure 42. Example ADP125 PCB Layout
Rev. 0 | Page 16 of 20
ADP124/ADP125
OUTLINE DIMENSIONS
3.10
3.00
2.90
2.26
2.16
2.06
8
1
5
4
5.05
4.90
4.75
3.10
3.00
2.90
1.83
1.73
1.63
TOP
VIEW
EXPOSED
PAD
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
PIN 1
INDICATOR
BOTTOM VIEW
0.525 BSC
1.10 MAX
0.65 BSC
SECTION OF THIS DATA SHEET.
0.94
0.86
0.78
0.23
0.18
0.13
0.70
0.55
0.40
0.15
0.10
0.05
SEATING
PLANE
8°
0°
0.40
0.33
0.25
COPLANARITY
0.10
COMPLIANT TO JEDEC STANDARDS MO-187-AA-T
Figure 43. 8-Lead Mini Small Outline Package with Exposed Pad [MINI_SO_EP]
(RH-8-1)
Dimensions shown in millimeters
ORDERING GUIDE
Model
Temperature Range (TJ)
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
–40°C to +125°C
Output Voltage (V)1
Package Description
8-Lead MINI_SO_EP
8-Lead MINI_SO_EP
8-Lead MINI_SO_EP
8-Lead MINI_SO_EP
8-Lead MINI_SO_EP
8-Lead MINI_SO_EP
8-Lead MINI_SO_EP
8-Lead MINI_SO_EP
Package Option
Branding
ADP124ARHZ-1.8-R72
ADP124ARHZ-2.5-R72
ADP124ARHZ-2.7-R72
ADP124ARHZ-2.8-R72
ADP124ARHZ-2.85-R72
ADP124ARHZ-2.9-R72
ADP124ARHZ-3.0-R72
ADP124ARHZ-3.3-R72
ADP125ARHZ-R72
1.8
2.5
2.7
2.8
2.85
2.9
3.0
3.3
RH-8-1
RH-8-1
RH-8-1
RH-8-1
RH-8-1
RH-8-1
RH-8-1
RH-8-1
RH-8-1
37
3T
3U
3Z
40
41
49
4F
38
0.8 to 5.0 (Adjustable) 8-Lead MINI_SO_EP
ADP124-3.3-EVALZ2
ADP125-EVALZ2
3.3
Adjustable
Evaluation Board
Evaluation Board
1 Up to 31 fixed-output voltage options from 1.75 V to 3.3 V are available. For additional voltage options, contact a local Analog Devices, Inc., sales or distribution
representative.
2 Z = RoHS Compliant Part.
Rev. 0 | Page 17 of 20
ADP124/ADP125
NOTES
Rev. 0 | Page 18 of 20
ADP124/ADP125
NOTES
Rev. 0 | Page 19 of 20
ADP124/ADP125
NOTES
©2009 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D08476-0-12/09(0)
Rev. 0 | Page 20 of 20
©2020 ICPDF网 联系我们和版权申明