ADP5022ACBZ-2-R7 [ADI]
Dual 3 MHz, 600 mA Buck Regulator with 150 mA LDO; 双3兆赫, 600毫安降压稳压器与150毫安LDO型号: | ADP5022ACBZ-2-R7 |
厂家: | ADI |
描述: | Dual 3 MHz, 600 mA Buck Regulator with 150 mA LDO |
文件: | 总28页 (文件大小:668K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Dual 3 MHz, 600 mA Buck
Regulator with 150 mA LDO
ADP5022
FEATURES
GENERAL DESCRIPTION
Input voltage range: 2.4 V to 5.5 V
Tiny 16-ball, 2 mm × 2 mm WLCSP package
Overcurrent and thermal protection
Soft start
Factory programmable undervoltage lockout on VDDA
system supply of either 2.2 V or 3.9 V
Factory programmable default output voltages for all
3 channels
Buck1 and Buck2 key specifications
Current mode architecture for excellent transient response
3 MHz operating frequency
Uses tiny multilayer inductors and capacitors
Forced PWM and auto PWM/PSM modes
Out-of-phase operation for reduced input filtering
100% duty cycle low dropout mode
24 μA typical quiescent current per channel, no switching
LDO key specifications
The ADP5022 is a micro power management unit (micro PMU)
that combines two high performance buck regulators and a low
dropout regulator (LDO) in a tiny 16-ball 2.08 mm × 2.08 mm
WLCSP to meet demanding performance and board space
requirements.
The high switching frequency of the buck regulators enables
tiny multilayer external components and minimizes the board
space required. When the MODE pin is set high, the buck reg-
ulators operate in forced PWM mode. When the MODE pin is
set low, the buck regulators automatically switch operating
modes, depending on the load current level. At higher output
loads, the buck regulators operate in PWM mode. When the
load current falls below a predefined threshold, the regulators
operate in power save mode (PSM), improving the light-load
efficiency.
The two bucks operate out-of-phase to reduce the input
capacitor requirement and noise.
Stable with 1 μF ceramic output capacitors
High PSRR
60 dB up to 10 KHz
The low quiescent current, low dropout voltage, and wide input
voltage range of the ADP5022 LDO extends the battery life of
portable devices. The LDO maintains power supply rejection
greater than 60 dB for frequencies as high as 10 kHz while
operating with a low headroom voltage.
Low output noise
65 μV rms output noise at VOUT3 = 3.3 V
Low dropout voltage: 150 mV @ 150 mA load
11 μA typical ground current at no load
Each regulator in the ADP5022 has a dedicated, independent
enable pin. A high voltage level applied to the enable pin activates
the respective regulator. The default output voltages are factory
programmable and can be set to a wide range of options.
APPLICATIONS
USB devices
Handheld products
Multivoltage power for processors, ASICS, FPGAs,
and RF chipsets
ADP5022
L1
COUT_3
1µH
SW1
V
@
OUT1
600mA
VIN1
EN1
V
= 2.4V
IN
TO 5.5V
VOUT1
PGND1
BUCK1
C4
C3
C4
ON
C2
4.7µF
10µF
OFF
EN_BK1
MODE
PWM
C1
C2
MODE
PWM/PSM
VIN2
L2
1µH
C3
4.7µF
SW2
MODE
V
@
OUT2
600mA
VOUT2
PGND2
ON
ON
BUCK2
C5
5.0mm
EN2
VDDA
VIN3
10µF
OFF
OFF
EN_BK2
C1
1µF
VOUT3
V
@
LDO1
EN_LDO1
OUT3
150mA
EN3
C6
1µF
L1
COUT_1 COUT_2
4.7mm
AGND
Figure 1. Typical Applications Circuit
Figure 2. Typical PCB Layout
Rev. A
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
©2009 Analog Devices, Inc. All rights reserved.
ADP5022
TABLE OF CONTENTS
Features .............................................................................................. 1
Theory of Operation ...................................................................... 16
Power Management Unit........................................................... 16
Buck Section................................................................................ 17
LDO Section ............................................................................... 18
Applications Information.............................................................. 19
Buck External Component Selection....................................... 19
LDO Capacitor Selection .......................................................... 20
PCB Layout Guidelines.................................................................. 22
Evaluation Board schematics and Artwork ................................ 23
Suggested Layout........................................................................ 23
Outline Dimensions....................................................................... 25
Ordering Guide .......................................................................... 25
Applications....................................................................................... 1
General Description......................................................................... 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
Buck1 and Buck2 Specifications................................................. 4
LDO Specifications ...................................................................... 5
Absolute Maximum Ratings............................................................ 6
Thermal Data................................................................................ 6
Thermal Resistance ...................................................................... 6
ESD Caution.................................................................................. 6
Pin Configuration and Function Descriptions............................. 7
Typical Performance Characteristics ............................................. 8
REVISION HISTORY
11/09—Revision A: Initial Version
Rev. A | Page 2 of 28
ADP5022
SPECIFICATIONS
VDDA = VIN1 = VIN2 = 3.6 V, VIN3 = (VOUT3 + 0.5 V) or 2.4 V, whichever is greater, VIN3 ≤ VIN1, TJ = −40°C to +125°C, unless
otherwise noted.1
Table 1.
Parameter
Symbol
Test Conditions/Comments
Min Typ Max Unit
INPUT VOLTAGE RANGE
System and Buck Input Supplies Voltage Range
VDDA, VIN1
and VIN2
,
Low UVLO level models
High UVLO level models
2.4
5.5
V
4.5
2.3
5.5
5.5
V
V
LDO Input Supply Voltage Range
SHUTDOWN CURRENT
VIN3
IGND-SD
EN1 = EN2 = EN3 = GND
EN1 = EN2 = EN3 = GND
TJ = −40°C to +85°C
0.5
μA
μA
2
THERMAL SHUTDOWN
Thermal Shutdown Threshold
Thermal Shutdown Hysteresis
EN1, EN2, EN3, MODE INPUTS
EN1, EN2, EN3, MODE Input Logic High
EN1, EN2, EN3, MODE Input Logic Low
EN1, EN2, EN3, MODE Input Leakage Current
STANDBY CURRENT
TSDTH
TSDHYS
TJ rising
150
20
°C
°C
VIH
VIL
VI-LEAKAGE
VDDA = VIN1 = VIN2
VDDA = VIN1 = VIN2
Pin at (VDDA = VIN1 = VIN2) or GND
1.2
V
V
μA
0.4
1
0.05
All Channels Enabled, No Load
All Channels Enabled, No Load, No Buck Switching
VIN3 UNDERVOLTAGE LOCKOUT
Input Voltage Rising
ISTBY
ISTBY-NOSW
80
59
μA
μA
85
UVLOVIN3RISE
UVLOVIN3FALL
2.20
V
V
Input Voltage Falling
1.45
VDDA UNDERVOLTAGE LOCKOUT
Input Voltage Rising
UVLOVDDARISE
UVLOVDDAFALL
High UVLO level (factory programmed)
Low UVLO level (factory programmed)
High UVLO level (factory programmed) 3.40
Low UVLO level (factory programmed) 2.00
4.15
2.35
V
V
V
V
Input Voltage Falling
1 All limits at temperature extremes are guaranteed via correlation using standard statistical quality control.
Rev. A | Page 3 of 28
ADP5022
BUCK1 AND BUCK2 SPECIFICATIONS
VDDA = VIN1 = VIN2 = 3.6 V, VIN3 = (VOUT3 + 0.5 V) or 2.4 V, whichever is greater, VIN3 ≤ VIN1, TJ = −40°C to +125°C, unless
otherwise noted.1
Table 2.
Parameter
Symbol
Test Conditions/Comments
Min
Typ
Max
Unit
OPERATING SUPPLY CURRENT
Buck1 Only
IGND1
ILOAD1 = 0 mA, device not switching, EN1
= VDDA, EN2 = EN3 = GND
ILOAD2 = 0 mA, device not switching, EN2
= VDDA, EN1 = EN3 = GND
ILOAD1 = ILOAD1 = 0 mA, device not switch-
ing, EN1 = EN2 = VDDA, EN3 = GND
24
32
48
ꢀA
ꢀA
ꢀA
Buck2 Only
IGND2
Buck1 and Buck2 Only
OUTPUT VOLTAGE ACCURACY
IGND1-2
64
+3
VOUT1, VOUT2
PWM mode, VIN1 = VIN2 = 2.4 V to 5.5 V, −3
ILOAD1 = ILOAD2 = 0 mA − 600 mA
%
POWER SAVE MODE TO PWM CURRENT
THRESHOLD
IPSM-PWM
IPWM-PSM
105
100
mA
mA
PWM TO POWER SAVE MODE CURRENT
THRESHOLD
SW CHARACTERISTICS, BUCK1 and BUCK2
PFET On Resistance
RPFET
RNFET
Typical at VIN1 = VIN2 = 3.6 V
Typical at VIN1 = VIN2 = 5.0 V
Typical at VIN1 = VIN2 = 3.6 V
Typical at VIN1 = VIN2 = 5.0 V
165
125
125
100
950
3.0
275
220
mΩ
mΩ
mΩ
mΩ
mA
MHz
NFET On Resistance
Current Limit
ILIMIT1, ILIMIT2
FSW
PFET switch peak current limit
750
2.5
1050
3.5
OSCILLATOR FREQUENCY
START-UP TIME2
From Shutdown State
TSTARTUP12-SD
250
ꢀs
1 All limits at temperature extremes are guaranteed via correlation using standard statistical quality control.
2 Start-up time is defined as the time from a rising edge on EN1/EN2 to VOUT1/VOUT2 reaching 90% of their nominal value.
Rev. A | Page 4 of 28
ADP5022
LDO SPECIFICATIONS
VDDA = VIN1 = VIN2 = 3.6 V, VIN3 = (VOUT3 + 0.5 V) or 2.3 V, whichever is greater, VIN3 ≤ VIN1, IOUT3 = 10 mA; CIN3 = COUT3
1 μF, TJ = −40°C to +125°C, unless otherwise noted.1
=
Table 3.
Parameter
OPERATING SUPPLY CURRENT2
Symbol
Test Conditions/Comments
Min
Typ
Max
Unit
IVIN3-GND
IOUT3 = 0 μA
IOUT3 = 10 mA
IOUT3 = 150 mA
11
16
31
21
29
43
μA
μA
μA
OUTPUT VOLTAGE ACCURACY
VOUT3
100 μA < IOUT3 < 150 mA,
−2
+2
%
VIN3 = (VOUT3 + 0.5 V) to 5.5 V
REGULATION
Line Regulation
Load Regulation3
DROPOUT VOLTAGE4
∆VOUT3/∆VIN3 VIN3 = (VOUT3 + 0.5 V) to 5.5 V, IOUT = 1 mA −0.03
∆VOUT3/∆IOUT3 IOUT3 = 1 mA to 150 mA
+0.03
%/V
0.002 0.0075 %/mA
VDROPOUT
VOUT3 = 3.0 V, IOUT3 = 10 mA
VOUT3 = 3.0 V, IOUT3 = 150 mA
7
110
mV
mV
150
350
START-UP TIME5
From Shutdown State
CURRENT-LIMIT THRESHOLD6
OUTPUT NOISE
TSTARTUP3-SD
ILIMIT3
200
240
μs
160
mA
OUTNOISE
10 Hz to 100 kHz, VIN3 = 5 V, VOUT3 = 3.3 V
10 Hz to 100 kHz, VIN3= 5 V, VOUT3 = 2.4 V
10 Hz to 100 kHz, VIN3 = 5 V, VOUT3 = 1.2 V
65
52
40
μV rms
μV rms
μV rms
POWER SUPPLY REJECTION RATIO
PSRR
10 kHz, VIN3 = 5 V, VOUT3 = 3.3 V
10 kHz, VIN3 = 5 V, VOUT3 = 2.3 V
10 kHz, VIN3 = 5 V, VOUT3 = 1.2 V
60
66
70
dB
dB
dB
1 All limits at temperature extremes are guaranteed via correlation using standard statistical quality control.
2 LDO operating supply current is the current drawn from VIN3 to AGND when the LDO is enabled. Whenever any regulator channel is enabled, current is drawn from
VIN1 to AGND. This current is 8 μA typical and is included in the IGND1, IGND2, and IGND1-2 specifications.
3 Based on an end-point calculation using 1 mA and 150 mA loads.
4 Dropout voltage is defined as the input-to-output voltage differential when the input voltage is set to the nominal output voltage. This applies only for output
voltages above 2.3 V.
5 Start-up time is defined as the time between the rising edge of EN3 to VOUT3 being at 90% of its nominal value.
6 Current-limit threshold is defined as the current at which VOUT3 drops to 90% of the specified typical value. For example, the current limit for a 3.0 V output voltage is
defined as the current that causes the output voltage to drop to 90% of 3.0 V or 2.7 V.
Rev. A | Page 5 of 28
ADP5022
ABSOLUTE MAXIMUM RATINGS
θJA of the package is based on modeling and calculation using a
4-layer board. The junction-to-ambient thermal resistance is
highly dependent on the application and board layout. In
applications where high maximum power dissipation exists,
close attention to thermal board design is required. The value
of θJA may vary, depending on PCB material, layout, and envi-
ronmental conditions. The specified values of θJA are based on a
4-layer, 4” × 3” circuit board. Refer to JEDEC JESD 51-9 for
detailed information on the board construction. For additional
information, see the AN-617 Application Note, MicroCSPTM
Wafer Level Chip Scale Package.
Table 4.
Parameter
Rating
VDDA, VIN1, VIN2, VIN3, VOUT1, VOUT2,
VOUT3, EN1, EN2, EN3, MODE to GND
−0.3 V to +6 V
Storage Temperature Range
Operating Junction Temperature Range
Soldering Conditions
−65°C to +150°C
−40°C to +125°C
JEDEC J-STD-020
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
THERMAL RESISTANCE
θJA is specified for the worst-case conditions, that is, a device
soldered on a circuit board.
THERMAL DATA
Table 5. Thermal Resistance
Absolute maximum ratings apply individually only, not in
combination.
Package Type
θJA
Unit
16-Ball, 0.5 mm Pitch WLCSP
65
°C/W
The ADP5022 can be damaged when the junction temperature
limits are exceeded. Monitoring ambient temperature (TA) does
not guarantee that the junction temperature (TJ) is within the
specified temperature limits. In applications with high power
dissipation and poor thermal resistance, the maximum ambient
temperature may have to be derated. In applications with
moderate power dissipation and low PCB thermal resistance,
the maximum ambient temperature may exceed the maximum
limit as long as the junction temperature is within specification
limits. TJ of the device is dependent on TA, the power
ESD CAUTION
dissipation (PD) of the device, and the junction-to-ambient
thermal resistance (θJA) of the package. Maximum TJ is
calculated from TA and PD using the following formula:
TJ = TA + (PD × θJA)
Rev. A | Page 6 of 28
ADP5022
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
BALL A1
INDICATOR
1
2
3
4
VOUT3 AGND VIN3 VDDA
A
VIN1
SW1
EN1
EN2
VIN2
B
C
D
EN3 MODE SW2
PGND1 VOUT1 VOUT2 PGND2
TOP VIEW
(BALL SIDE DOWN)
Not to Scale
Figure 3. Pin Configuration
Table 6. Pin Function Descriptions
Pin No.
A1
A2
A3
A4
B1
Mnemonic
VOUT3
AGND
VIN3
VDDA
VIN1
Description
LDO Output Voltage and Sensing Input.
Analog Ground.
LDO Input Supply (VIN3 ≤ VIN1 = VIN2 = VDDA).
Supply Input for the Housekeeping Block and UVLO Sensing.
Buck1 Input Supply (VIN1 = VIN2 = VDDA).
B2
B3
B4
EN1
EN2
VIN2
Buck1 Activation. Set EN1 = high: turn on Buck1. Set EN1 = low: turn off Buck1.
Buck2 Activation. Set EN2 = high: turn on Buck2. Set EN2 = low: turn off Buck2.
Buck2 Input Supply (VIN2 = VIN1 = VDDA).
C1
SW1
Buck1 Switching Node.
C2
EN3
LDO Activation. Set EN3 = high: turn on LDO. EN3 = low: turn off LDO.
C3
C4
MODE
SW2
Buck1/Buck2 Operating Mode: MODE = high: forced PWM operation. MODE = low: auto PWM/PSM operation.
Buck2 Switching Node.
D1
D2
D3
D4
PGND1
VOUT1
VOUT2
PGND2
Dedicated Power Ground for Buck1.
Buck1 Output Voltage Sensing Input.
Buck2 Output Voltage Sensing Input.
Dedicated Power Ground for Buck2.
Rev. A | Page 7 of 28
ADP5022
TYPICAL PERFORMANCE CHARACTERISTICS
VIN1 = VIN2 = VIN3 = VDDA = 5.0 V, TA = 25°C, unless otherwise noted.
T
T
SW
4
2
VOUT1
1
VOUT
VOUT2
2
EN
1
3
I
IN
VOUT3
3
B
B
B
B
B
B
CH1 2.00V
CH3 2.00V
CH2 2.00V
M 200µs
A CH1
1.92V
CH1 2.00V
CH3 5.00V
CH2 50.0mA Ω
CH4 5.00V
M 40.0µs
A CH3
2.2V
W
W
W
W
W
B
W
W
T 45.40%
T 11.20%
Figure 4. 3-Channel Start-Up Waveforms, VIN3 Cascaded from VOUT1
Figure 7. Buck2 Startup, VOUT2 = 1.8 V, IOUT2 = 5 mA
0.15
0.14
0.13
0.12
0.11
0.10
0.09
0.08
0.07
0.06
0.00010
0.00008
0.00006
0.00004
0.00002
PSM TO PWM
PWM TO PSM
0
2.4
2.9
3.4
3.9
4.4
4.9
5.4
2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 4.0 4.2 4.4 4.6 4.8 5.0 5.2 5.4
INPUT VOLTAGE (V)
V
(V)
IN
Figure 5. System Quiescent Current vs. Input Voltage, VOUT1 = 0.8 V,
VOUT2 = 2.5 V, VIN3 = VOUT2, VOUT3 = 1.2 V, All Channels Unloaded
Figure 8. Buck 2 PSM to PWM Transition, VOUT2 = 1.8 V
T
T
T
T
= +25°C
= –40°C
= +85°C
A
A
A
3.354
3.334
3.314
3.294
3.274
3.254
3.234
SW
4
VOUT
2
EN
1
I
IN
3
B
B
B
CH1 2.00V
CH3 5.00V
CH2 50.0mA Ω
CH4 5.00V
M 40.0µs
A CH3
2.2V
W
W
W
0
0.1
0.2
0.3
(A)
0.4
0.5
0.6
B
W
I
OUT
T
11.20%
Figure 9. Buck1 Load Regulation Across Temperature, VOUT1 = 3.3 V,
Auto Mode
Figure 6. Buck1 Startup, VOUT1 = 3.3 V, IOUT1 = 10 mA
Rev. A | Page 8 of 28
ADP5022
100
90
80
70
60
50
40
30
20
10
0
1.834
1.824
1.814
T
T
T
= +25°C
= –40°C
= +85°C
A
A
A
V
V
V
= 3.6V
= 4.5V
= 5.5V
IN
IN
IN
1.804
1.794
1.784
1.774
1.764
0
0.1
0.2
0.3
(A)
0.4
0.5
0.6
0.0001
0.001
0.01
I (A)
OUT
0.1
1
I
OUT
Figure 10. Buck2 Load Regulation Across Temperature, VOUT2 = 1.8 V,
Auto Mode
Figure 13. Buck1 Efficiency vs. Load Current, Across Input Voltage,
VOUT1 = 3.3 V, Auto Mode
100
90
80
70
60
50
40
30
1.834
V
V
V
V
= 5.5V
= 4.5V
= 3.6V
= 2.4V
IN
IN
IN
IN
1.824
1.814
1.804
1.794
1.784
V
V
V
= 3.6V
= 4.5V
= 5.5V
IN
IN
IN
20
10
0
1.774
1.764
0
0.1
0.2
0.3
(A)
0.4
0.5
0.6
0.001
0.01
0.1
1
I
I
(A)
OUT
OUT
Figure 11. Buck 2 Load Regulation Across Input Voltage, VOUT1 = 1.8 V,
PWM Mode
Figure 14. Buck1 Efficiency vs. Load Current, Across Input Voltage,
VOUT1 = 3.3 V, PWM Mode
100
90
80
70
60
50
40
30
3.354
3.334
3.314
3.294
3.274
V
V
V
= 3.6V
= 4.5V
= 5.5V
IN
IN
IN
V
V
V
V
= 5.5V
= 4.5V
= 3.6V
= 2.4V
IN
IN
IN
IN
20
10
3.254
3.234
0
0
0.1
0.2
0.3
(A)
0.4
0.5
0.6
0.0001
0.001
0.01
(A)
0.1
1
I
I
OUT
OUT
Figure 12. Buck1 Load Regulation Across Input Voltage, VOUT2 = 3.3 V,
PWM Mode
Figure 15. Buck2 Efficiency vs. Load Current, Across Input Voltage,
VOUT2 = 1.8 V, Auto Mode
Rev. A | Page 9 of 28
ADP5022
100
90
80
70
60
50
40
30
20
10
100
90
80
70
60
50
40
30
20
10
0
V
V
V
V
= 5.5V
= 4.5V
= 3.6V
= 2.4V
T
T
T
= –40°C
= +25°C
= +85°C
IN
IN
IN
IN
A
A
A
0
0.001
0.01
0.1
1
0.0001
0.001
0.01
I (A)
OUT
0.1
1
I
(A)
OUT
Figure 16. Buck2 Efficiency vs. Load Current, Across Input Voltage,
VOUT2 = 1.8 V, PWM Mode
Figure 19. Buck1 Efficiency vs. Load Current, Across Temperature,
VOUT1 = 3.3 V, Auto Mode
100
90
80
70
60
50
40
30
100
90
80
70
60
50
40
30
V
V
V
V
= 2.4V
= 3.6V
= 4.5V
= 5.5V
T
T
T
= +25°C
= –40°C
= +85°C
IN
IN
IN
IN
A
A
A
20
10
20
10
0
0
0.0001
0.001
0.01
(A)
0.1
1
0.0001
0.001
0.01
I (A)
OUT
0.1
1
I
OUT
Figure 17. Buck1 Efficiency vs. Load Current, Across Input Voltage,
VOUT1 = 0.8 V, Auto Mode
Figure 20. Buck2 Efficiency vs. Load Current, Across Temperature,
VOUT2 = 1.8 V, Auto Mode
100
90
80
70
60
50
40
30
3.5
T
T
T
= +25°C
= –40°C
= +85°C
A
A
A
3.4
3.3
3.2
3.1
3.0
2.9
2.8
2.7
2.6
2.5
V
V
V
V
= 2.4V
= 3.6V
= 4.5V
= 5.5V
IN
IN
IN
IN
20
10
0
0.001
0.01
0.1
1
0
0.1
0.2
0.3
0.4
0.5
0.6
I
(A)
OUT
OUTPUT CURRENT (A)
Figure 18. Buck1 Efficiency vs. Load Current, Across Input Voltage,
VOUT1 = 0.8 V, PWM Mode
Figure 21. Buck2 Switching Frequency vs. Output Current, Across
Temperature, VOUT2 = 1.8 V, PWM Mode
Rev. A | Page 10 of 28
ADP5022
T
T
VOUT
VOUT
1
2
1
2
I
I
SW
SW
SW
SW
4
4
B
B
CH1 50.0V
CH2 500mA Ω
CH4 2.00V
M 4.00µs A CH2
240mA
CH1 50mV
CH2 500mA Ω
CH4 2.00V
M 400ns A CH2
220mA
W
W
B
B
W
W
T
28.40%
T 28.40%
Figure 22. Typical Waveforms, VOUT1 = 3.3 V, IOUT1 = 30 mA, Auto Mode
Figure 25. Typical Waveforms, VOUT2 = 1.8 V, IOUT2 = 30 mA, PWM Mode
T
T
VOUT
1
VIN
I
SW
VOUT
1
2
SW
SW
3
4
B
B
CH1 50.0mV
CH3 1.00V
M 1.00ms
A
CH3
4.80V
CH1 50.0V
CH2 500mA Ω
CH4 2.00V
M 4.00µs A CH2
220mA
W
W
W
B
B
B
CH4 2.00V
W
W
T
30.40%
T
28.40%
Figure 26. Buck1 Response to Line Transient, Input Voltage from 4.5 V to
5.0 V, VOUT1 = 3.3 V, PWM Mode
Figure 23. Typical Waveforms, VOUT2 = 1.8 V, IOUT2 = 30 mA, Auto Mode
T
T
VOUT
1
VIN
I
SW
VOUT
2
1
SW
SW
4
3
4
B
CH1 50mV
CH2 500mA Ω
CH4 2.00V
M 400ns A CH2
220mA
B
B
W
CH1 50.0mV
CH3 1.00V
M 1.00ms
A
CH3
4.80V
W
W
B
B
W
CH4 2.00V
W
T
28.40%
T
30.40%
Figure 24. Typical Waveforms, VOUT1 = 3.3 V, IOUT1 = 30 mA, PWM Mode
Figure 27. Buck2 Response to Line Transient, VIN = 4.5 V to 5.0 V,
VOUT2 = 1.8 V, PWM Mode
Rev. A | Page 11 of 28
ADP5022
T
T
SW
SW
4
1
4
1
VOUT
VOUT
I
OUT
I
OUT
2
2
B
B
B
CH1 100mV
CH2 200mA Ω
CH4 5.00V
M 20.0µs A CH2
T 19.20%
88.0mA
W
W
W
B
B
B
CH1 50.0mV
W CH2 50.0mA Ω
CH4 5.00V
M 20.0µs A CH2
T 60.000µs
356mA
W
W
Figure 28. Buck1 Response to Load Transient, IOUT1 from 1 mA to 50 mA,
VOUT1 = 3.3 V, Auto Mode
Figure 31. Buck2 Response to Load Transient, IOUT2 from 20 mA to 180 mA,
VOUT2 = 1.8 V, Auto Mode
T
T
SW
VOUT2
2
4
SW1
VOUT
1
3
VOUT1
1
SW2
I
OUT
2
4
B
B
B
B
B
B
B
CH1 5.00V
CH3 5.00V
CH2 5.00V
CH4 5.00V
M 400ns A CH4
T 50.00%
1.90V
CH1 50.0mV
W CH2 50.0mA Ω
CH4 5.00V
M 20.0µs A CH2
T 22.20%
379mA
W
W
W
W
W
W
Figure 29. Buck2 Response to Load Transient, IOUT2 from 1 mA to 50 mA,
VOUT2 = 1.8 V, Auto Mode
Figure 32. VOUT and SW Waveforms for Buck1 and Buck2 in PWM Mode
Showing Out-of-Phase Operation
T
T
SW
4
I
IN
2
1
3
VOUT
1
VOUT
EN
I
OUT
2
B
B
B
B
B
B
CH1 50.0mV
W CH2 200mA Ω
CH4 5.00V
M 20.0µs A CH2
T 20.40%
408mA
CH1 2.00V
CH3 5.00V
CH2 50.0mA Ω
M 40.0µs
T 11.20%
A CH3
2.2V
W
W
W
W
W
W
B
Figure 30. Buck1 Response to Load Transient, IOUT1 from 20 mA to 180 mA,
VOUT1 = 3.3 V, Auto Mode
Figure 33. LDO Startup, VOUT3 = 3.0 V, IOUT3 = 5 mA
Rev. A | Page 12 of 28
ADP5022
2.820
2.815
2.810
2.805
2.800
2.795
2.790
2.785
2.780
50
45
40
35
30
25
20
15
10
5
150mA
100mA
10mA
1mA
100µA
1µA
V
V
V
V
= 3.3V
= 4.5V
= 5.0V
= 5.5V
IN
IN
IN
IN
0
3.3
0
0.02
0.04
0.06
0.08
(A)
0.10
0.12
0.14
3.8
4.3
4.8
5.3
I
OUT
INPUT VOLTAGE (V)
Figure 34. LDO Load Regulation Across Input Voltage, VOUT3 = 2.8 V
Figure 37. LDO Ground Current vs. Input Voltage, Across Output Load,
VOUT3 = 2.8 V
2.85
50
45
40
35
30
25
20
15
10
5
T
T
T
= –40°C
= +25°C
= +85°C
A
A
A
2.84
2.83
2.82
2.81
2.80
2.79
2.78
2.77
2.76
2.75
0
0
0.02
0.04
0.06
0.08
(A)
0.10
0.12
0.14
0.16
0
0.02
0.04
0.06
0.08
0.10
0.12
0.14
I
LOAD CURRENT (A)
OUT
Figure 35. LDO Load Regulation Across Temperature, VIN3 = 3.3 V, VOUT3 = 2.8 V
Figure 38. LDO Ground Current vs. Output Load, VIN3 = 3.3 V, VOUT3 = 2.8 V
3.0
2.5
2.0
1.5
3.0
2.5
2.0
1.5
I
I
I
I
I
= 150mA
= 100mA
= 10mA
= 1mA
OUT
OUT
OUT
OUT
OUT
1.0
1.0
V
V
V
= 3.6V
= 4.5V
= 5.5V
IN
IN
IN
0.5
0
0.5
0
= 100µA
0
0.05
0.10
0.15
0.20
(A)
0.25
0.30
0.35
0.40
2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 4.0 4.2 4.4 4.6 4.8 5.0 5.2 5.4
I
V
(V)
OUT
IN
Figure 36. LDO Line Regulation Across Output Load, VOUT3 = 2.8 V
Figure 39. LDO Current Capability Across Input Voltage, VOUT3 = 2.8 V
Rev. A | Page 13 of 28
ADP5022
65
60
T
5VIN
I
OUT
3.3VIN
55
50
45
40
35
30
2
1
VOUT
25
0.001
B
B
W
CH1 100mV
CH2 100mA Ω
M 40.0µs A CH2
52.0mA
W
0.01
0.1
1
10
100
I (mA)
LOAD
T
19.20%
Figure 40. LDO Response to Load Transient, IOUT3 from 1 mA to 80 mA,
VOUT3 = 2.8 V
Figure 43. LDO Output Noise vs. Load Current, Across Input Voltage,
VOUT3 = 3.0 V
0
T
100µA
1mA
–10
10mA
50mA
–20
VIN
100mA
150mA
–30
–40
–50
–60
–70
–80
–90
–100
VOUT
1
3
B
CH1 20.0mV
CH3 1.00V
M 100µs
28.40%
A
CH3
4.80V
W
W
10
100
1k
10k
100k
1M
10M
B
T
FREQUENCY (Hz)
Figure 41. LDO Response to Line Transient, Input Voltage from 4.5 V to 5.5 V,
VOUT3 = 2.8 V
Figure 44. LDO PSRR Across Output Load, VIN3 = 3.3 V, VOUT3 = 2.8 V
60
0
–20
–40
–60
5VIN
55
3.3VIN
50
45
40
35
30
–80
100µA
1mA
10mA
50mA
–100
100mA
150mA
100k
FREQUENCY (Hz)
25
0.001
–120
10
0.01
0.1
1
10
100
100
1k
10k
1M
10M
I
(mA)
LOAD
Figure 42. LDO Output Noise vs. Load Current, Across Input Voltage,
VOUT3 = 2.8 V
Figure 45. LDO PSRR Across Output Load, VIN3 = 3.3 V, VOUT3 = 3.0 V
Rev. A | Page 14 of 28
ADP5022
0
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
100µA
1mA
10mA
50mA
100mA
150mA
100µA
1mA
10mA
50mA
100mA
150mA
–20
–40
–60
–80
–100
–120
10
100
1k
10k
100k
1M
10M
10
100
1k
10k
100k
1M
10M
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 46. LDO PSRR Across Output Load, VIN3 = 5.0 V, VOUT3 = 2.8 V
Figure 47. LDO PSRR Across Output Load, VIN3 = 5.0 V, VOUT3 = 3.0 V
Rev. A | Page 15 of 28
ADP5022
THEORY OF OPERATION
VOUT1 VOUT2
GM ERROR
AMP
GM ERROR
AMP
PWM
PWM
COMP
COMP
SOFT START
SOFT START
VIN2
VIN1
I
I
LIMIT
LIMIT
PSM
PSM
COMP
COMP
PWM/
PSM
PWM/
PSM
CONTROL
BUCK1
CONTROL
BUCK2
LOW
CURRENT
LOW
CURRENT
SW2
SW1
OSCILLATOR
DRIVER
AND
ANTISHOOT
THROUGH
DRIVER
AND
ANTISHOOT
THROUGH
SYSTEM
UNDERVOLTAGE
LOCK OUT
THERMAL
SHUTDOWN
PGND2
PGND1
LDO
UNDERVOLTAGE
LOCK OUT
EN1
EN2
EN3
R1
R2
ENABLE
CONTROL
LDO
CONTROL
ADP5022
VDDA VIN3
AGND VOUT3
MODE
Figure 48. Functional Block Diagram
The buck regulators can operate in forced PWM mode if the
MODE pin is at a logic high level. In forced PWM mode, the
switching frequency of the two bucks is always constant and
does not change with the load current. If the MODE pin is at a
logic low level, the switching regulators operate in an auto
PWM/ PSM mode. In this mode, the regulators operate at fixed
PWM frequency when the load current is above the power
saving current threshold. When the load current falls below the
power saving current threshold, the regulator in question enters
power saving mode where the switching occurs in bursts. The
burst repetition is a function of the current load and the output
capacitor value. This operating mode reduces the switching
and quiescent current losses. The auto PWM/PSM mode
transition is controlled independently for each buck regulator.
POWER MANAGEMENT UNIT
The ADP5022 is a micro power management units (micro
PMU) combining two step-down (buck) dc-to-dc converters
and a single low dropout linear regulator (LDO). The high
switching frequency and tiny 16-ball WLCSP package allow for
a small power management solution.
To combine these high performance converters and regulators
into the micro PMU, there is a system controller allowing them
to operate together.
Each regulator has a dedicated enable pin. EN1 controls the
activation for Buck1, EN2 controls the activation for Buck2,
and EN3 controls the activation of the LDO. Logic high applied to
the ENx pin turns on the regulator, and a logic low applied to
the ENx pin turns off the regulator. When a regulator is turned
on, the output voltage is controlled through a soft start circuit to
avoid a large inrush current due to the discharged output
capacitors.
The two bucks operate synchronized to each other.
Rev. A | Page 16 of 28
ADP5022
Thermal Protection
PWM Mode
In the event that the junction temperature rises above 150°C,
the thermal shutdown circuit turns off the converters and the
LDO. Extreme junction temperatures can be the result of high
current operation, poor circuit board design, or high ambient
temperature. A 20°C hysteresis is included so that when thermal
shutdown occurs, the bucks and LDO do not return to opera-
tion until the on-chip temperature drops below 130°C. When
coming out of thermal shutdown, soft start is initiated.
In PWM mode, the bucks operate at a fixed frequency of 3 MHz
set by an internal oscillator. At the start of each oscillator cycle,
the PFET switch is turned on, sending a positive voltage across
the inductor. Current in the inductor increases until the current
sense signal crosses the peak inductor current threshold that
turns off the PFET switch and turns on the NFET synchronous
rectifier. This sends a negative voltage across the inductor,
causing the inductor current to decrease. The synchronous
rectifier stays on for the rest of the cycle. The buck regulates the
output voltage by adjusting the peak inductor current threshold.
Undervoltage Lockout
To protect against battery discharge, undervoltage lockout
(UVLO) circuitry is integrated in the system. If the input
voltage on VDDA drops below a typical 2.15 V UVLO
threshold, all channels shut down. In the buck channels,
both the power switch and the synchronous rectifier turn
off. When the voltage on VDDA rises above the UVLO
threshold, the part is enabled once more.
Power Save Mode (PSM)
The bucks smoothly transition to PSM operation when the
load current decreases below the PSM current threshold. When
either of the bucks enter power save mode, an offset is induced
in the PWM regulation level, which makes the output voltage
rise. When the output voltage reaches a level approximately
1.5% above the PWM regulation level, PWM operation is
turned off. At this point, both power switches are off, and the
buck enters an idle mode. The output capacitor discharges until
the output voltage falls to the PWM regulation voltage, at which
point the device drives the inductor to make the output voltage
rise again to the upper threshold. This process is repeated while
the load current is below the PSM current threshold.
Alternatively, the user can select device models with a UVLO
set at a higher level, suitable for USB applications. For these
models, the device hits the turn-off threshold when the input
supply drops to 3.65 V typical.
Enable/Shutdown
When all three enable pins are held low, the device is in
shutdown mode, and the input current remains below 2 ꢀA.
PSM Current Threshold
BUCK SECTION
The PSM current threshold is set to 100 mA. The bucks employ
a scheme that enables this current to remain accurately con-
trolled, independent of input and output voltage levels. This
scheme also ensures that there is very little hysteresis between
the PSM current threshold for entry to and exit from the PSM.
The PSM current threshold is optimized for excellent efficiency
over all load currents.
The two bucks use a fixed frequency and high speed current
mode architecture.
The bucks operate with an input voltage of 2.4 V to 5.5 V.
Control Scheme
The bucks operate with a fixed frequency, current mode PWM
control architecture at medium to high loads for high efficiency
but shift to a power save mode (PSM) control scheme at light
loads to lower the regulation power losses. When operating in
fixed frequency PWM mode, the duty cycle of the integrated
switches is adjusted and regulates the output voltage. When
operating in PSM at light loads, the output voltage is controlled
in a hysteretic manner, with higher output voltage ripple. During
part of this time, the converter is able to stop switching and
enters an idle mode, which improves conversion efficiency.
Oscillator/Phasing of Inductor Switching
The ADP5022 ensures that both bucks operate at the same
switching frequency when both bucks are in PWM mode.
Additionally, the ADP5022 ensures that when both bucks are
in PWM mode, they operate out-of-phase, whereby the Buck2
PFET starts conducting exactly half a clock period after the
Buck1 PFET starts conducting.
Rev. A | Page 17 of 28
ADP5022
Enable/Shutdown
LDO SECTION
The bucks start operation with soft start when the EN1 or EN2
pin is toggled from logic low to logic high. Pulling the EN1 or
EN2 pin low disables that channel.
The LDO is a low quiescent current, low dropout linear
regulator and provides up to 150 mA of output current.
Drawing a low 30 ꢀA quiescent current (typical) at full load
makes the LDO ideal for battery-operated portable equipment.
Short-Circuit Protection
The LDO operates with an input voltage of 2.3 V to 5.5 V.
The bucks include frequency foldback to prevent output current
runaway on a hard short. When the voltage at the feedback pin
falls below half the target output voltage, indicating the possi-
bility of a hard short at the output, the switching frequency is
reduced to half the internal oscillator frequency. The reduction
in the switching frequency allows more time for the inductor to
discharge, preventing a runaway of output current.
It also provides high power supply rejection ratio (PSRR), low
output noise, and excellent line and load transient response
with just a small 1 μF ceramic input and output capacitor.
Internally, the LDO consists of a reference, an error amplifier,
a feedback voltage divider, and a PMOS pass transistor. Output
current is delivered via the PMOS pass device, which is con-
trolled by the error amplifier. The error amplifier compares
the reference voltage with the feedback voltage from the output
and amplifies the difference. If the feedback voltage is lower
than the reference voltage, the gate of the PMOS device is
pulled lower, allowing more current to flow and increasing
the output voltage. If the feedback voltage is higher than the
reference voltage, the gate of the PMOS device is pulled higher,
reducing the current flowing to the output.
Soft Start
The bucks have an internal soft start function that ramps the
output voltage in a controlled manner upon startup, thereby
limiting the inrush current. This prevents possible input voltage
drops when a battery or a high impedance power source is
connected to the input of the converter.
Current Limit
Each buck has protection circuitry to limit the amount of
positive current flowing through the PFET switch and the
amount of negative current flowing through the synchronous
rectifier. The positive current limit on the power switch limits
the amount of current that can flow from the input to the
output. The negative current limit prevents the inductor
current from reversing direction and flowing out of the load.
LDO Undervoltage Lockout
The ADP5022 integrates an undervoltage lockout function
on the VIN3 input voltage, which ensures that the LDO
output drive is disabled whenever VIN3 is below a threshold
of approximately 2.0 V. Where the ADP5022 is configured to
supply VIN3 from either VOUT1 or VOUT2, this ensures that
the LDO powers up safely in this cascaded configuration.
100% Duty Operation
With a drop in input voltage or with an increase in load current,
the buck may reach a limit where, even with the PFET switch
on 100% of the time, the output voltage drops below the desired
output voltage. At this limit, the buck transitions to a mode
where the PFET switch stays on 100% of the time. When the
input conditions change again and the required duty cycle
falls, the buck immediately restarts PWM regulation without
allowing overshoot on the output voltage. This is particularly
useful in battery-powered applications to achieve the longest
operation time by taking full advantage of the whole battery
voltage range. Maintaining regulation is dependent on the input
voltage, load current, and output voltage. This can be calculated
from the following equation:
V
IN(MIN) = VOUT(MAX) + ILOAD(MAX) × (RDS(on)MAX + RL)
where:
V
OUT(MAX) is the nominal output voltage plus the maximum
tolerance.
LOAD(MAX) is the maximum load current plus inductor ripple
current.
DS(on)MAX is the maximum P-channel switch RDS(on)
RL is the DC resistance of the inductor.
I
R
.
Rev. A | Page 18 of 28
ADP5022
APPLICATIONS INFORMATION
Output Capacitor
BUCK EXTERNAL COMPONENT SELECTION
Trade-offs between performance parameters such as efficiency
and transient response can be made by varying the choice of
external components in the applications circuit, as shown in
Figure 1.
Higher output capacitor values reduce the output voltage ripple
and improve load transient response. When choosing this value,
it is also important to account for the loss of capacitance due to
output voltage dc bias.
Inductor
Ceramic capacitors are manufactured with a variety of dielec-
trics, each with a different behavior over temperature and
applied voltage. Capacitors must have a dielectric adequate
to ensure the minimum capacitance over the necessary
temperature range and dc bias conditions. X5R or X7R
dielectrics with a voltage rating of 6.3 V or 10 V are recom-
mended for best performance. Y5V and Z5U dielectrics are
not recommended for use with any dc-to-dc converter because
of their poor temperature and dc bias characteristics.
The high switching frequency of the ADP5022 bucks allows for
the selection of small chip inductors. For best performance, use
inductor values between 0.7 ꢀH and 3 ꢀH. Suggested inductors
are shown in Table 7.
The peak-to-peak inductor current ripple is calculated using
the following equation:
VOUT ×(VIN −VOUT
)
IRIPPLE
=
V
IN × fSW ×L
The worst-case capacitance accounting for capacitor variation
over temperature, component tolerance, and voltage is calcu-
lated using the following equation:
where:
SW is the switching frequency.
L is the inductor value.
f
CEFF = COUT × (1 − TEMPCO) × (1 − TOL)
The minimum dc current rating of the inductor must be greater
than the inductor peak current. The inductor peak current is
calculated using the following equation:
where:
C
EFF is the effective capacitance at the operating voltage.
TEMPCO is the worst-case capacitor temperature coefficient.
TOL is the worst-case component tolerance.
IRIPPLE
IPEAK = ILOAD(MAX)
+
In this example, the worst-case temperature coefficient
2
(TEMPCO) over −40°C to +85°C is assumed to be 15% for an
X5R dielectric. The tolerance of the capacitor (TOL) is assumed
to be 10%, and COUT is 9.2481 ꢀF at 1.8 V, as shown in Figure 49.
Inductor conduction losses are caused by the flow of current
through the inductor, which has an associated internal dc
resistance (DCR). Larger sized inductors have smaller DCR,
which may decrease inductor conduction losses. Inductor core
losses are related to the magnetic permeability of the core material.
Because the bucks are high switching frequency dc-to-dc
converters, shielded ferrite core material is recommended for
its low core losses and low EMI.
Substituting these values in the equation yields
CEFF = 9.2481 ꢀF × (1 − 0.15) × (1 − 0.1) = 7.0747 ꢀF
To guarantee the performance of the bucks, it is imperative
that the effects of dc bias, temperature, and tolerances on the
behavior of the capacitors be evaluated for each application.
12
Table 7. Suggested 1.0 μH Inductors
Dimensions
(mm)
ISAT
(mA)
DCR
(mΩ)
Vendor
Murata
Murata
Model
10
8
LQM2MPN1R0NG0B 2.0 × 1.6 × 0.9
LQM18FN1R0M00B 1.6 × 0.8 × 0.8
1.6 × 0.8 × 0.8
2.0 × 2.0 × 1.4
GLFR1608T1R0M-LR 1.6 × 0.8 × 0.8
1400
150
290
900
230
85
26
90
59
80
81
85
Taiyo Yuden CBMF1608T1R0M
Coilcraft
TDK
Coilcraft
Toko
EPL2014-102ML
6
0603LS-102
MDT2520-CN
1.8 × 1.69 × 1.1 400
2.5 × 2.0 × 1.2
4
1350
2
0
0
1
2
3
4
5
6
DC BIAS VOLTAGE (V)
Figure 49. Typical Capacitor Performance
Rev. A | Page 19 of 28
ADP5022
The peak-to-peak output voltage ripple for the selected output
capacitor and inductor values is calculated using the following
equation:
Input Capacitor
Higher value input capacitors help to reduce the input voltage
ripple and improve transient response. Maximum input capa-
citor current is calculated using the following equation:
VIN
×2×L×COUT
IRIPPLE
8× fSW ×COUT
VRIPPLE
=
=
(
2π × fSW
)
VOUT (VIN −VOUT
)
ICIN ≥ ILOAD(MAX)
Capacitors with lower equivalent series resistance (ESR) are
preferred to guarantee low output voltage ripple, as shown in
the following equation:
VIN
To minimize supply noise, place the input capacitor as close
to the VIN pin of the BUCK as possible. As with the output
capacitor, a low ESR capacitor is recommended.
VRIPPLE
IRIPPLE
ESRCOUT
≤
The effective capacitance needed for stability, which includes
temperature and dc bias effects, is a minimum of 3 μF and a
maximum of 10 μF. A list of suggested capacitors is shown in
Table 9.
The effective capacitance needed for stability, which includes
temperature and dc bias effects, is a minimum of 7 μF and a
maximum of 40 μF.
Table 9. Suggested 4.7 μF Capacitors
Table 8. Suggested 10 μF Capacitors
Voltage
Case Rating
Size (V)
GRM188R60J475ME19D 0402 6.3
Case
Size
Voltage
Rating (V)
Vendor
Murata
Taiyo Yuden
TDK
Type
X5R
X5R
X5R
X5R
Model
Vendor
Type Model
X5R
GRM188R60J106
JMK107BJ475
C1608JB0J106K
ECJ1VB0J106M
0603
0603
0603
0603
6.3
6.3
6.3
6.3
Murata
Taiyo Yuden X5R
Panasonic X5R
JMK107BJ475
0402 6.3
0402 6.3
ECJ-0EB0J475M
Panasonic
The buck regulators require 10 μF output capacitors to guar-
antee stability and response to rapid load variations and to
transition in and out the PWM/PSM modes. In certain
applications, where one or both buck regulator powers a
processor, the operating state is known because it is con-
trolled by software. In this condition, the processor can drive
the MODE pin according to the operating state; consequently, it
is possible to reduce the output capacitor from 10 μF to 4.7 μF
because the regulator does not expect a large load variation
when working in PSM mode, see Figure 50.
LDO CAPACITOR SELECTION
Output Capacitor
The ADP5022 LDO is designed for operation with small, space-
saving ceramic capacitors but functions with most commonly
used capacitors as long as care is taken with the ESR value. The
ESR of the output capacitor affects stability of the LDO control
loop. A minimum of 0.70 μF capacitance with an ESR of 1 Ω
or less is recommended to ensure stability of the ADP5022.
Transient response to changes in load current is also affected
by output capacitance. Using a larger value of output capacit-
ance improves the transient response of the ADP5022 to large
changes in load current.
ADP5022
L1
1µH
PROCESSOR
C2
4.7µF
MICRO PMU
VIN1
VIN2
SW1
VCORE
VOUT1
PGND1
C4
4.7µF
Input Bypass Capacitor
V
IN
2.5V TO 5.5V
C3
4.7µF
Connecting a 1 μF capacitor from VIN3 to GND reduces
the circuit sensitivity to printed circuit board (PCB) layout,
especially when long input traces or high source impedance
are encountered. If greater than 1 μF of output capacitance is
required, increase the input capacitor to match it.
MODE
GPIO
VIO
VDDA
VIN3
L2
1µH
C1
1µF
SW2
VOUT2
PGND2
C5
4.7µF
ANALOG
SUB-SYSTEM
Table 10. Suggested 1.0 μF Capacitors
EN1
EN2
EN3
VOUT3
Case
Size
Voltage
Rating (V)
VANA
C6
1µF
Vendor
Murata
TDK
Panasonic
Taiyo Yuden
Type
X5R
X5R
X5R
X5R
Model
GRM155B30J105K
C1005JB0J105KT
ECJ0EB0J105K
LMK105BJ105MV-F
0402
0402
0402
0402
6.3
6.3
6.3
10.0
Figure 50. Processor System Power Management with PSM/PWM Control
Rev. A | Page 20 of 28
ADP5022
Input and Output Capacitor Properties
Use the following equation to determine the worst-case capa-
citance accounting for capacitor variation over temperature,
component tolerance, and voltage.
Use any good quality ceramic capacitors with the ADP5022
as long as they meet the minimum capacitance and maximum
ESR requirements. Ceramic capacitors are manufactured with
a variety of dielectrics, each with a different behavior over
temperature and applied voltage. Capacitors must have a
dielectric adequate to ensure the minimum capacitance over
the necessary temperature range and dc bias conditions. X5R
or X7R dielectrics with a voltage rating of 6.3 V or 10 V are
recommended for best performance. Y5V and Z5U dielectrics
are not recommended for use with any LDO because of their
poor temperature and dc bias characteristics.
CEFF = CBIAS × (1 − TEMPCO) × (1 − TOL)
where:
CBIAS is the effective capacitance at the operating voltage.
TEMPCO is the worst-case capacitor temperature coefficient.
TOL is the worst-case component tolerance.
In this example, the worst-case temperature coefficient
(TEMPCO) over −40°C to +85°C is assumed to be 15% for an
X5R dielectric. The tolerance of the capacitor (TOL) is assumed
to be 10% and CBIAS is 0.94 ꢀF at 1.8 V as shown in Figure 51.
Figure 51 depicts the capacitance vs. voltage bias characteristic
of a 0402 1 μF, 10 V, X5R capacitor. The voltage stability of a
capacitor is strongly influenced by the capacitor size and voltage
rating. In general, a capacitor in a larger package or higher voltage
rating exhibits better stability. The temperature variation of the
X5R dielectric is about 15% over the −40°C to +85°C tempera-
ture range and is not a function of package or voltage rating.
Substituting these values into the following equation.
CEFF = 0.94 ꢀF × (1 − 0.15) × (1 − 0.1) = 0.719 ꢀF
Therefore, the capacitor chosen in this example meets the
minimum capacitance requirement of the LDO over
temperature and tolerance at the chosen output voltage.
To guarantee the performance of the ADP5022, it is imperative
that the effects of dc bias, temperature, and tolerances on the
behavior of the capacitors are evaluated for each application.
1.2
1.0
0.8
0.6
0.4
0.2
0
0
1
2
3
4
5
6
DC BIAS VOLTAGE (V)
Figure 51. Capacitance vs. Voltage Characteristic
Rev. A | Page 21 of 28
ADP5022
PCB LAYOUT GUIDELINES
Poor layout can affect ADP5022 performance, causing electro-
magnetic interference (EMI) and electromagnetic compatibility
(EMC) problems, ground bounce, and voltage losses. Poor
layout can also affect regulation and stability. A good layout is
implemented using the following guidelines:
•
•
•
Route the output voltage path away from the inductor and
SW node to minimize noise and magnetic interference.
Maximize the size of ground metal on the component side
to help with thermal dissipation.
Use a ground plane with several vias connecting to
the component side ground to further reduce noise
interference on sensitive circuit nodes.
•
Place the inductor, input capacitor, and output capacitor
close to the IC using short tracks. These components carry
high switching frequencies, and large tracks act as antennas.
Rev. A | Page 22 of 28
ADP5022
EVALUATION BOARD SCHEMATICS AND ARTWORK
C2
0603
J1
L1
1µH
4.7µF
J8
J9
J2
B1
C1
D2
D1
VIN1
SW1
C3
0603
4.7µF
C
0603
10µF
_1
OUT
B4
A4
A3
A2
C3
B2
BUCK1
J3
J4
VIN2
VOUT1
PGND1
VDDA
C1
0402
1µF
VIN3
L2
1µH
AGND
MODE
EN1
J10
C4
D3
D4
R1
SW2
VOUT2
PGND2
0Ω
C
0603
10µF
_2
_3
OUT
BUCK2
LDO
J13
J12
J5
B3
C2
EN2
EN3
A1
VOUT3
J7
J6
C
OUT
0402
1µF
R2
0Ω
J11
Figure 52. Evaluation Board Schematic
SUGGESTED LAYOUT
Figure 53. Top Layer, Recommended Layout
Figure 54. Second Layer, Recommended Layout
Rev. A | Page 23 of 28
ADP5022
Figure 55. Third Layer, Recommended Layout
Figure 56. Bottom Layer, Recommended Layout
Rev. A | Page 24 of 28
ADP5022
OUTLINE DIMENSIONS
0.660
0.602
0.544
2.12
2.08 SQ
2.04
0.022
REF
SEATING
PLANE
4
3
2
1
A
BALL 1
IDENTIFIER
B
C
D
0.330
0.310
0.290
1.50
REF
0.50
REF
0.04 NOM
COPLANARITY
0.380
0.352
0.324
TOP VIEW
(BALL SIDE DOWN)
BOTTOM VIEW
(BALL SIDE UP)
0.280
0.250
0.220
Figure 57. 16-Ball Wafer Level Chip Scale Package [WLCSP]
Back-Coating Included
(CB-16-7)
Dimensions shown in millimeters
ORDERING GUIDE
Output
Undervoltage
Lockout Level
Temperature
Range
Package
Option
Branding
Code
Model
ADP5022ACBZ-1-R72
Voltage (V)1
Package Description
VOUT1 = 3.3 V
VOUT2 = 1.5 V
VOUT3 = 1.8 V
VOUT1 = 1.2 V
VOUT2 = 1.8 V
VOUT3 = 2.8 V
VOUT1 = 3.3 V
VOUT2 = 1.8 V
VOUT3 = 3.3 V
Low
Low
High
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
16-Ball Wafer Level Chip Scale Package [WLCSP]
16-Ball Wafer Level Chip Scale Package [WLCSP]
16-Ball Wafer Level Chip Scale Package [WLCSP]
CB-16-7
CB-16-7
CB-16-7
L9H
ADP5022ACBZ-2-R72
ADP5022ACBZ-4-R72
L9J
LG7
1 For additional voltage options, contact a local sales or distribution representative. Additional output voltages and UVLO available are
Buck1 and Buck2: 3.3 V, 3.0 V, 2.8 V, 2.5 V, 2.3 V, 2.0 V, 1.82 V, 1.8 V, 1.6 V, 1.5 V, 1.3 V, 1.2 V, 1.1 V, 1.0 V, 0.9 V, 0.8 V
LDO: 3.3 V, 3.0 V, 2.9 V, 2.8 V, 2.775 V, 2.5 V, 2.0 V, 1.875 V, 1.8 V, 1.75 V, 1.7 V, 1.65 V, 1.6 V, 1.55 V, 1.5 V, 1.2 V
UVLO: 2.25 V or 3.9 V
2 Z = RoHS Compliant Part.
Rev. A | Page 25 of 28
ADP5022
NOTES
Rev. A | Page 26 of 28
ADP5022
NOTES
Rev. A | Page 27 of 28
ADP5022
NOTES
©2009 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D08253-0-11/09(A)
Rev. A | Page 28 of 28
相关型号:
ADP5030ACBZ-1228R7
DUAL OUTPUT, FIXED POSITIVE LDO REGULATOR, PBGA16, 1.60 X 1.60 MM, 0.40 MM PITCH, ROHS COMPLIANT, WLCSP-16
ROCHESTER
©2020 ICPDF网 联系我们和版权申明