ADRV9010BBCZ_技术文档

Integrated, Quad RF Transceiver

with Observation Path

ADRV9010

Data Sheet

The complete transceiver subsystem includes automatic and

manual attenuation control, dc offset correction, quadrature

error correction (QEC), and digital filtering, eliminating the need

for these functions in the digital baseband. Other auxiliary

functions such as analog-to-digital converters (ADCs), digital-to-

analog converters (DACs), and general-purpose input/outputs

(GPIOs) that provide an array of digital control options are also

integrated.

FEATURES

4 differential transmitters

4 differential receivers

2 observation receivers with 2 inputs each

Center frequency

650 MHz to 3800 MHz (ADRV9010BBCZ)

650 MHz to 6000 MHz (ADRV9010BBCZ-A)

Maximum receiver bandwidth: 200 MHz

Maximum transmitter bandwidth: 200 MHz

Maximum transmitter synthesis bandwidth: 450 MHz

Maximum observation receiver bandwidth: 450 MHz

Fully integrated independent fractional-N radio frequency

synthesizers

To achieve a high level of RF performance, the transceiver

includes five fully integrated phase-locked loops (PLLs). Two

PLLs provide high performance, low power fractional-N RF

synthesis for the transmitter and receiver signal paths. One fully

integrated PLL also supports an independent local oscillator (LO)

mode for the observation receiver. Another PLL generates the

clocks needed for the converters and digital circuits and a fifth

PLL provides the clock for the serial data interface. A multichip

synchronization mechanism synchronizes the phases of all LOs

and baseband clocks between multiple ADRV9010 chips. All

voltage controlled oscillators (VCOs) and loop filter components

are integrated and adjustable through the digital control interface.

Fully integrated clock synthesizer

Multichip phase synchronization for all local oscillators and

baseband clocks

JESD204B/JESD204C digital interface

APPLICATIONS

3G/4G/5G TDD macro and small cell base stations

TDD active antenna systems for advanced LTE and 5G

GENERAL DESCRIPTION

The serial data interface consists of eight serializer lanes and eight

deserializer lanes. The interface supports both the JESD204B and

JESD204C standards, operating at data rates up to 16.22016 Gbps.

The interface also supports interleaved mode for lower bandwidths,

thus reducing the number of high speed data interface lanes to

one. Both fixed and floating-point data formats are supported.

The floating-point format allows internal automatic gain

control (AGC) to be invisible to the demodulator device.

The ADRV9010 is a highly integrated, radio frequency (RF) agile

transceiver that offers four independently controlled transmitters,

dedicated observation receiver inputs for monitoring each

transmitter channel, four independently controlled receivers,

integrated synthesizers, and digital signal processing functions

to provide a complete transceiver solution. The device provides the

high radio performance and low power consumption demanded by

cellular infrastructure applications such as TDD-based small cell

base station radios, macro 3G/4G/5G TDD systems, and TDD

based massive multiple in/multiple out (MIMO) base stations.

The ADRV9010BBCZ operates from 650 MHz to 3800 MHz,

covering most of the licensed and unlicensed cellular bands.

The ADRV9010BBCZ-A operates from 650 MHz to 6000 MHz.

The ADRV9010 is powered directly from 1.0 V, 1.3 V, and 1.8 V

regulators and is controlled via a standard serial peripheral

interface (SPI). Comprehensive power-down modes are included

to minimize power consumption in normal use. The

ADRV9010 is packaged in a 14 mm × 14 mm, 289-ball chip

scale ball grid array (CSP_BGA).

The receiver subsystem consists of four independent, wide

bandwidth, direct conversion receivers with state-of-the-art

dynamic range. The four independent transmitters use an

innovative direct conversion modulator that achieves high

modulation accuracy with exceptionally low noise. The

ADRV9010 device also includes two wide bandwidth, time

shared observation path receivers with two inputs each for

monitoring transmitter outputs.

Rev. E

Document Feedback

Information furnished by Analog Devices is believed to be accurate and reliable. However, no

responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other

rights of third parties that may result from its use. Specifications subject to change without notice. No

license is granted by implication or otherwise under any patent or patent rights of Analog Devices.

Trademarks and registeredtrademarks arethe property of their respective owners.

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.

Technical Support

www.analog.com

ADRV9010

Data Sheet

TABLE OF CONTENTS

Features.............................................................................................. 1

4800 MHz Band.......................................................................... 82

5700 MHz Band.......................................................................... 96

Theory of Operation .................................................................... 110

General....................................................................................... 110

Transmitter ............................................................................... 110

Receiver ..................................................................................... 110

Observation Receiver............................................................... 110

Clock Input ............................................................................... 111

Synthesizers............................................................................... 111

SPI Interface.............................................................................. 111

Power Supply Sequence........................................................... 111

GPIO_x Pins ............................................................................. 112

Auxiliary Converters ............................................................... 112

JTAG Boundary Scan .............................................................. 112

Applications Information ........................................................... 113

Power Supply Sequence........................................................... 113

Data Interface ........................................................................... 113

Outline Dimensions..................................................................... 115

Ordering Guide ........................................................................ 115

Applications ...................................................................................... 1

General Description......................................................................... 1

Revision History ............................................................................... 2

Functional Block Diagram .............................................................. 3

Specifications .................................................................................... 4

Power Supply Specifications..................................................... 17

Current Consumption............................................................... 18

Digital Interface and Timing Specifications........................... 19

Absolute Maximum Ratings ......................................................... 20

Junction Temperature ............................................................... 20

Reflow Profile.............................................................................. 20

Thermal Resistance.................................................................... 20

ESD Caution................................................................................ 20

Pin Configuration and Function Descriptions .......................... 21

Typical Performance Characteristics........................................... 26

800 MHz Band............................................................................ 26

1800 MHz Band.......................................................................... 40

2600 MHz Band.......................................................................... 54

3800 MHz Band.......................................................................... 68

REVISION HISTORY

1/2021—Revision E: Initial Version

Rev. E | Page 2 of 115

Data Sheet

ADRV9010

FUNCTIONAL BLOCK DIAGRAM

8

VDDA_1P8

VDDA_1P3

GPIO_ANA_x

GPIO

AUXILIARY ADC

AUXILIARY DAC

4

ADRV9010

AUXADC_x

19

POWER

MANAGEMENT

VDDA_1P0

VIF

GPIO_x

VDIG_1P0

CLOCK GENERATION

AND

SYNCHRONIZATION

DEVCLK±

SYSREF±

LO3

RF SYNTHESIZER

MICROPROCESSOR

SPI_CLK

SPI_EN

SPI_DO

SPI_DIO

SPI PORT

LO1

LO2

EXT_LO1±

EXT_LO2±

GPINT1

GPINT2

4

Rx3, Rx4, Tx3, Tx4, ORx3/ORx4

Rx1, Rx2, Tx1, Tx2, ORx1/ORx2

RXx_EN

CONTROL

INTERFACE

4

TXx_EN

4

ORX_CTRL_x

RX3+

RX3–

RESET

Rx1

Rx2

TEST_EN

RX4+

RX4–

DECIMATION,

ADC

RX1+

RX1–

pFIR,

AGC,

SERDOUTA±

SERDOUTB±

SERDOUTC±

SERDOUTD±

SERDOUTE±

SERDOUTF±

SERDOUTG±

SERDOUTH±

SYNCIN1±

DC OFFSET,

QEC,

RX2+

RX2–

LO1

LO2

0

90

TUNING,

RSSI,

OVERLOAD

ADC

DAC

TX3+

TX3–

Tx1

Tx2

SYNCIN2±

TX4+

TX4–

SYNCIN3±

TX1+

TX1–

pFIR,

LO LEAKAGE,

QEC,

TUNING,

INTERPOLATION

JESD204B/

JESD204C

SERIAL

TX2+

TX2–

LO1

LO2

0

INTERFACE

SERDINA±

SERDINB±

SERDINC±

SERDIND±

SERDINE±

SERDINF±

SERDING±

SERDINH±

SYNCOUT1±

SYNCOUT2±

90

DAC

ADC

ORX3+

ORX3–

ORx1/ORx2

ORX4+

ORX4–

DECIMATION,

pFIR,

ORX1+

ORX1–

DC OFFSET,

QEC,

0

90

LO3

TUNING,

OVERLOAD

ORX2+

ORX2–

ADC

NOTES

1. VDDA_1P8 REPRESENTS VCONV1_1P8, VCONV2_1P8, VANA1_1P8, VANA2_1P8, VANA3_1P8, VANA4_1P8, AND VJVCO_1P8.

VDDA_1P3 REPRESENTS VANA1_1P3, VANA2_1P3, VCONV1_1P3, VCONV2_1P3, VRFVCO1_1P3, VRFVCO2_1P3, VAUXVCO_1P3,

VCLKVCO_1P3, VRFSYN1_1P3, VRFSYN2_1P3, VCLKSYN_1P3, VAUXSYN_1P3, VRXLO_1P3, AND VTXLO_1P3.

VDDA_1P0 REPRESENTS VJSYN_1P0, VDES_1P0, VTT_DES, AND VSER_1P0.

Figure 1.

Rev. E | Page 3 of 115

ADRV9010

Data Sheet

SPECIFICATIONS

All specifications are verified using a Wenzel Associates Model 500-23867, 245.76 MHz voltage controlled crystal oscillator (VCXO)

as the device clock, unless otherwise noted. Specifications are applicable over the lifetime of the device. Power supplies are as follows:

VDDA_1P8 = 1.8 V, VIF = 1.8 V, VDDA_1P3 = 1.3 V, VDDA_1P0 = 1.0 V, and VDIG_1P0 = 1.0 V. VDDA_1P8 represents VCONV1_1P8,

VCONV2_1P8, VANA1_1P8, VANA2_1P8, VANA3_1P8, VANA4_1P8, and VJVCO_1P8. VDDA_1P3 represents VANA1_1P3,

VANA2_1P3, VCONV1_1P3, VCONV2_1P3, VRFVCO1_1P3, VRFVCO2_1P3, VAUXVCO_1P3, VCLKVCO_1P3, VRFSYN1_1P3,

VRFSYN2_1P3, VCLKSYN_1P3, VAUXSYN_1P3, VRXLO_1P3, and VTXLO_1P3. VDDA_1P0 represents VJSYN_1P0, VDES_1P0,

VTT_DES, and VSER_1P0. All RF specifications are based on measurements that include printed circuit board (PCB) and matching

circuit losses, unless otherwise noted.

Table 1.

Parameter

Symbol

Min

Typ

Max

Unit

Test Conditions/Comments

TRANSMITTERS (Tx)

Center Frequency

650

3800

6000

450

MHz

ADRV9010BBCZ

ADRV9010BBCZ-A

Wider bandwidth for use in digital

processing algorithms

Tx Synthesis Bandwidth

Tx Large Signal

Bandwidth

Peak-to-Peak Gain

Deviation

200

MHz

dB

Zero-IF mode

1.0

0.1

1

450 MHz bandwidth, includes

compensation by programmable

finite impulse response (pFIR) filter

Any 20 MHz bandwidth span within

the large signal bandwidth, includes

compensation by pFIR filter

dB

Deviation from Linear

Phase

Degrees

450 MHz bandwidth

Maximum Output Power

0 dBFS, 1 MHz signal input, 50 Ω load,

0 dB Tx attenuation

800 MHz

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

Power Control Range

Power Control Resolution

Attenuation Accuracy

6.4

6.0

6.1

6.5

6.0

5.7

32

dBm

dB

0.05

dB

Integral Nonlinearity

(Gain)

INL

0.1

dB

Valid over full power control range

for any 4 dB step

Differential

DNL

0.04

dB

Monotonic

Nonlinearity (Gain)

Output Power

Temperature Slope

LO Delay Temperature

Slope

−4.5

1.05

mdB/°C

ps/°C

Valid over full power control range

Rev. E | Page 4 of 115

Data Sheet

ADRV9010

Parameter

Symbol

Min

Typ

Max

Unit

Test Conditions/Comments

Adjacent Channel

Leakage Power Ratio

(ACLR) Long Term

Evolution (LTE)

20 MHz LTE at −12 dBFS

800 MHz

1800 MHz

−67

dB

2600 MHz

−67

dB

3800 MHz

−67

dB

4800 MHz

−65

dB

5700 MHz

−65

dB

Inband Noise Floor

−154.5

dBFS/Hz

0 dB attenuation, inband noise falls

1 dB for each decibel of attenuation

for attenuation settings between

0 dB and 20 dB

Interpolation Images

−76

dBc

Tx to Tx Isolation: All Tx

Output Effects on All

Other Tx Outputs

800 MHz

1800 MHz

2600 MHz

3800 MHz

4800 MHz

80

76

74

70

64

dB

5700 MHz

Image Rejection

Within Large Signal

Bandwidth

QEC active up to 20 dB of attenuation,

continuous wave (CW) tone swept

across the large signal bandwidth

800 MHz

75

76

65

61

dB

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

Beyond Large Signal

Bandwidth

Assumes that distortion power density

is 25 dB less than the desired power

density

800 MHz

1800 MHz

2600 MHz

3800 MHz

4800 MHz

40

38

34

37

50

dB

Ω

5700 MHz

Output Impedance

Z_OUT

Differential and nominal

Maximum Output Load

Voltage Standing

3

Maximum value to ensure adequate

calibration

Wave Ratio (VSWR)

Output Return Loss

10

dB

Rev. E | Page 5 of 115

ADRV9010

Data Sheet

Parameter

Symbol

Min

Typ

Max

Unit

Test Conditions/Comments

Output Third-Order

Intercept Point

OIP3

0 dB Tx attenuation, 90 MHz and

95 MHz tones

800 MHz

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

Carrier Leakage

30

29

27

dBm

With LO leakage correction active,

0 dB Tx attenuation; scales dB for dB

with attenuation

Carrier Offset from LO

Carrier on the LO

−82

−71

dBFS/MHz

dBFS/MHz Measured using an LTE 20 MHz signal

Error Vector Magnitude

EVM

PLL optimized for narrow-band noise,

measured using LTE 20 MHz signal

800 MHz

0.36

0.60

0.42

0.50

0.67

0.84

%

50 kHz PLL bandwidth

500 kHz PLL bandwidth

200 kHz PLL bandwidth

400 kHz PLL bandwidth

500 kHz PLL bandwidth

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

Transmitter TDD

Parameters

Time from SPI_EN

Going High to

Change in Tx

Attenuation

Time Between

Consecutive

Microattenuation

Steps

t_SCH

12

20

ns

t_ACH

A large change in attenuation may

be broken up into a series of smaller

attenuation changes

Attenuation

Overshoot During

Transition

0.1

dB

Change in

Attenuation per

Microstep

RECEIVERS (Rx)

Center Frequency

650

3800

6000

MHz

dB

ADRV9010BBCZ

ADRV9010BBCZ-A

Gain Range

30

Attenuation Accuracy

Analog Gain Step

0.5

1

0.1

dB

Attenuator steps from 0 dB to 6 dB

Attenuator steps from 6 dB to 30 dB

Residual Gain Step

Error

Gain Temperature

Slope

Internal LO Delay

−6.4

1.0

mdB/°C

ps/°C

Temperature Slope

Rev. E | Page 6 of 115

Data Sheet

ADRV9010

Parameter

Symbol

Min

Typ

Max

Unit

Test Conditions/Comments

Frequency Response

Peak-to-Peak Gain

Deviation

1

dB

200 MHz bandwidth, includes

compensation by pFIR filter

Any 20 MHz span, includes

compensation by pFIR filter

0.2

Rx Bandwidth

Rx Alias Band Rejection

200

MHz

dB

80

Due to digital filters

Maximum Useable

Input Level

P_HIGH

This CW signal level corresponds to

the signal level seen at the matching

circuit input that produces −2 dBFS at

the digital output with 0 dB channel

attenuation

800 MHz

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

−12.7

−12.2

−12

−11.3

−10.3

dBm

Maximum Source VSWR

Input Impedance

Input Port Return Loss

Noise Figure

800 MHz

1800 MHz

2600 MHz

3800 MHz

4800 MHz

3

Z_IN

100

10

Ω

dB

Differential

0 dB attenuation at Rx port

11

dB

11.5

11.9

12

12.5

14.5

1.5

5700 MHz

Noise Figure Ripple

At band edge

Second-Order Input

Intermodulation

Intercept Point

IIP2

0 dB attenuation, complex

800 MHz

65

68

62

58

dBm

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

Third-Order Input

Intermodulation

Intercept Point,

Difference Product

Wideband

WB-IIP3_DIFF

Two tones near the band edge; P_HIGH

− 9 dB per tone

800 MHz

14.5

17

16.5

17

18

dBm

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

Rev. E | Page 7 of 115

ADRV9010

Data Sheet

Parameter

Symbol

Min

Typ

Max

Unit

Test Conditions/Comments

Midband

MB-IIP3_DIFF

Two tones near middle of the band;

P_HIGH− 9 dB per tone

800 MHz

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

Wideband

18.8

27

22

dBm

20

WB-IIP3_SUM

Two tones approximately

bandwidth/6 offset from the LO; P_HIGH

− 9 dB per tone

800 MHz

18

20

21

23

22

dBm

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

Second-Order Harmonic

Distortion

Maximum Input

HD2_MAX

−72

−75

dBc

P

_HIGHCW signal, harmonic distortion

tones falling within 100 MHz of the LO

P_HIGH− 3 dB CW signal, harmonic

Recommended Input HD2

distortion tones falling within

100 MHz of the LO

Third-Order Harmonic

Distortion

Maximum Input

HD3_MAX

−66

−72

dBc

P

_HIGHCW signal, harmonic distortion

tones falling within 100 MHz of the LO

P_HIGH− 3 dB CW signal, harmonic

Recommended Input HD3

distortion tones falling within

100 MHz of the LO

Fourth-Order Harmonic

Distortion

Maximum Input

HD4_MAX

−90

dBc

P

_HIGHCW signal, harmonic distortion

tones falling within 100 MHz of the LO

P_HIGH− 3 dB CW signal, harmonic

Recommended Input HD4

distortion tones falling within 100

MHz of the LO

Fifth-Order Harmonic

Distortion

Maximum Input

HD5_MAX

−87

−90

dBc

P

_HIGHCW signal, harmonic distortion

tones falling within 100 MHz of the LO

P_HIGH− 3 dB CW signal, harmonic

Recommended Input HD5

distortion tones falling within

100 MHz of the LO

Image Rejection

75

dB

QEC active, within 200 MHz Rx

bandwith

Rx to Rx Signal Isolation

800 MHz

1800 MHz

2600 MHz

3800 MHz

75

69

64

61

58

dB

4800 MHz

5700 MHz

Rev. E | Page 8 of 115

Data Sheet

ADRV9010

Parameter

Symbol

Min

Typ

Max

Unit

Test Conditions/Comments

Rx Band Spurs

Referenced to RF Input

at Maximum Gain

−95

dBm

No more than one spur at this level

per 10 MHz of Rx bandwidth;

excludes converter clock spurs;

no input signal applied

Spurious-Free Dynamic

Range

SFDR

81

dBc

P_HIGHCW signal anywhere inside

the band 20 MHz, excludes

harmonic distortion products

Rx Input LO Leakage at

Maximum Gain

Leakage decreased dB for dB with

attenuation for first 12 dB

800 MHz

1800 MHz

2600 MHz

3800 MHz

4800 MHz

−65

−63

−65

−59

−53

−55

dBm

5700 MHz

Tx to Rx Signal Isolation

800 MHz

All Tx output effects on all Rx inputs

80

73

72

68

66

dB

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

OBSERVATION RECEIVER

(ORx)

Center Frequency

650

3800

6000

MHz

dB

ADRV9010BBCZ

ADRV9010BBCZ-A

Gain Range

30

Analog Gain Step

0.5

dB

For attenuator steps from 0 dB to

6 dB

Peak-to-Peak Gain

Deviation

1

dB

450 MHz RF bandwidth,

compensation by pFIR filter

0.1

1

dB

Any 20 MHz bandwidth span,

compensation by pFIR filter

450 MHz RF bandwidth

Deviation from Linear

Phase

Degrees

ORx Bandwidth

ORx Alias Band

Rejection

450

MHz

dB

60

Due to digital filters

Maximum Useable

Input Level

P_HIGH

This CW signal level corresponds to

the signal level seen at the matching

circuit input that produces −2 dBFS

at the digital output with 0 dB

channel attenuation

800 MHz

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

Input Impedance

Input Source VSWR

Input Port Return Loss

−12.7

−12.2

−10.6

−12.0

−11.3

−9.0

dBm

ꢀ

Z_IN

100

Differential

3

10

dB

Rev. E | Page 9 of 115

ADRV9010

Data Sheet

Parameter

Symbol

Min

Typ

Max

Unit

Test Conditions/Comments

Integrated Noise

450 MHz Bandwidth

−58.5

dBFS

Sample rate at maximum value

integrated from 500 kHz to 225 MHz,

no input signal

491.52 MHz

Bandwidth

(Nyquist)

−57.5

dBFS

Sample rate at maximum value

integrated from 500 kHz to

245.76 MHz, no input signal

Second-Order Input

Intermodulation

Intercept Point

IIP2

Maximum ORx gain; P_HIGH– 11 dB per

tone

800 MHz

53

65

48

45

55

dBm

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

Third-Order Input

Intermodulation

Intercept Point

Maximum ORx gain; P_HIGH– 11 dB per

tone

Narrow Band

IIP3_NB

IM3 product < 130 MHz at baseband;

P_HIGH– 11 dB per tone, 491.52 MSPS

800 MHz

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

Wide Band

12

15

18

17

18

dBm

IIP3_WB

IM3 products > 130 MHz at

baseband; P_HIGH− 11 dB per tone,

491.52 MSPS

800 MHz

9

dBm

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

12

11

13

Third-Order

Intermodulation

Product

Narrow Band

IM3_NB

IM3 product < 130 MHz at baseband;

two tones, each at P_HIGH− 11 dB,

491.52 MSPS

800 MHz

−71.5

−76.5

−80

−77

dBc

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

−76

Rev. E | Page 10 of 115

Data Sheet

ADRV9010

Parameter

Symbol

Min

Typ

Max

Unit

Test Conditions/Comments

Wide Band

IM3_WB

IM3 product > 130 MHz at baseband;

two tones, each at P_HIGH– 11 dB,

491.52 MSPS

800 MHz

−65.5

−70.5

−67

−68

−65

dBc

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

−66

Fifth-Order

Intermodulation

Product

Narrow Band

IM5_NB

IM5 product < 130 MHz at baseband;

two tones, each at P_HIGH− 11 dB,

491.52 MSPS

800 MHz

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

Wide Band

−91

−96

−85

−82

−78

dBc

IM5_WB

IM5 product > 130 MHz at baseband;

two tones, each at P_HIGH− 11 dB,

491.52 MSPS

800 MHz

−87

−85

−73

−78

dBc

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

Seventh-Order

Intermodulation

Product

Narrow Band

IM7_NB

IM7 product < 130 MHz at baseband;

two tones, each at P_HIGH− 11 dB,

491.52 MSPS

800 MHz

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

Wide Band

−74

−79

−77

−71

−74

dBc

IM7_WB

IM7 product > 130 MHz at baseband;

two tones, each at P_HIGH− 11 dB,

491.52 MSPS

800 MHz

−79

−80

−71

−84

dBc

1800 MHz

2600 MHz

3800 MHz

4800 MHz

5700 MHz

Rev. E | Page 11 of 115

ADRV9010

Data Sheet

Parameter

Symbol

Min

Typ

Max

Unit

Test Conditions/Comments

Spurious-Free Dynamic

Range

SFDR

64

dB

Nonintermodulation related spurs;

does not include harmonic

distortion; input set at P_HIGH− 8 dB

Second-Order Harmonic

Distortion

Inband

HD2

HD3

Input set at P_HIGH− 8 dB

−80

−73

dBc

Inband harmonic distortion falls

within 100 MHz

Out of band harmonic distortion falls

within 225 MHz

Out of Band

Third-Order Harmonic

Distortion

Input set at P_HIGH− 8 dB

Inband

−70

−65

dBc

Harmonic distortion falls within

100 MHz

Harmonic distortion falls within

225 MHz

After online tone calibration, QEC

active

Out of Band

Image Rejection

Within Large Signal

Bandwidth

Outside Large Signal

Bandwidth

75

dB

Tx to ORx Signal Isolation

All Tx output effects on all ORx

inputs

800 MHz

1800 MHz

2600 MHz

3800 MHz

4800 MHz

90

85

88

77

76

dB

5700 MHz

LO SYNTHESIZER

LO Frequency Step

LO1, LO2

7.3

Hz

1.6 GHz to 3.2 GHz, 245.76 MHz phase

frequency detector (PFD) frequency

LO Spectral Purity

−80

dBc

Integrated Phase Noise

Integrated from 1 kHz to 100 MHz

Narrow Bandwidth

Optimized

PLL optimized to minimize phase

noise at offsets > 200 kHz

800 MHz LO

1800 MHz LO

2600 MHz LO

3800 MHz LO

4800 MHz LO

5700 MHz LO

0.12

0.27

0.66

0.53

0.91

1.57

°rms

Wide Bandwidth

Optimized

PLL bandwidth optimized for

integrated phase noise and phase

noise at offsets > 1 MHz

800 MHz LO

1800 MHz LO

2600 MHz LO

3800 MHz LO

4800 MHz LO

5700 MHz LO

0.07

0.11

0.17

0.26

0.30

0.42

°rms

Rev. E | Page 12 of 115

Data Sheet

ADRV9010

Parameter

Symbol

Min

Typ

Max

Unit

Test Conditions/Comments

Spot Phase Noise,

Narrow Band

PLL optimized to minimize phase

noise at offsets > 200 kHz

800 MHz LO

100 kHz Offset

1 MHz Offset

10 MHz Offset

1800 MHz LO

100 kHz Offset

200 kHz Offset

400 kHz Offset

600 kHz Offset

800 kHz Offset

1.2 MHz Offset

1.8 MHz Offset

6 MHz Offset

10 MHz Offset

2600 MHz LO

100 kHz Offset

1 MHz Offset

10 MHz Offset

3800 MHz LO

100 kHz Offset

1 MHz Offset

10 MHz Offset

4800 MHz LO

100 kHz Offset

1 MHz Offset

10 MHz Offset

5700 MHz LO

100 kHz Offset

1 MHz Offset

10 MHz Offset

−115

−141

−162

dBc/Hz

−107

−115

−123

−128

−131

−136

−140

−151

−156

dBc/Hz

−97

−124

−150

dBc/Hz

−100

−126

−149

dBc/Hz

−94

−120

−145

dBc/Hz

−89

−115

−141

dBc/Hz

Spot Phase Noise,

Wide Band

PLL bandwidth optimized for

integrated phase noise and phase

noise at offsets > 1 MHz

800 MHz LO

100 kHz Offset

1 MHz Offset

10 MHz Offset

1800 MHz LO

100 kHz Offset

1 MHz Offset

10 MHz Offset

2600 MHz LO

100 kHz Offset

1 MHz Offset

10 MHz Offset

3800 MHz LO

100 kHz Offset

1 MHz Offset

10 MHz Offset

−114

−141

−162

dBc/Hz

−112

−133

−156

dBc/Hz

−112

−120

−149

dBc/Hz

−104

−125

−149

dBc/Hz

Rev. E | Page 13 of 115

ADRV9010

Data Sheet

Parameter

Symbol

Min

Typ

Max

Unit

Test Conditions/Comments

4800 MHz LO

100 kHz Offset

1 MHz Offset

10 MHz Offset

5700 MHz LO

−106

−117

−144

dBc/Hz

100 kHz Offset

1 MHz Offset

10 MHz Offset

AUXILIARY SYNTHESIZER

LO Frequency Step

−104

−112

−140

dBc/Hz

LO3

1.8

Hz

1.625 GHz to 3.25 GHz, 61.44 MHz

PFD frequency

LO Spectral Purity

−65

dBc

|f_RFLO− f_AUXLO|¹> 15 MHz

Integrated Phase Noise

Integrated from 1 kHz to 100 MHz,

PLL bandwidth optimized for

integrated phase noise

800 MHz LO

1800 MHz LO

2600 MHz LO

3800 MHz LO

4800 MHz LO

5700 MHz LO

Spot Phase Noise

800 MHz LO

0.18

0.22

0.46

0.43

0.70

1.12

°rms

100 kHz Offset

1 MHz Offset

10 MHz Offset

1800 MHz LO

100 kHz Offset

1 MHz Offset

10 MHz Offset

2600 MHz LO

100 kHz Offset

1 MHz Offset

10 MHz Offset

3800 MHz LO

100 kHz Offset

1 MHz Offset

10 MHz Offset

4800 MHz LO

100 kHz Offset

1 MHz Offset

10 MHz Offset

5700 MHz LO

100 kHz Offset

1 MHz Offset

10 MHz Offset

−112

−121

−141

dBc/Hz

−110

−120

−134

dBc/Hz

−103

−114

−132

dBc/Hz

−104

−114

−128

dBc/Hz

−100

−110

−127

dBc/Hz

−95

−106

−126

dBc/Hz

Rev. E | Page 14 of 115

Data Sheet

ADRV9010

Parameter

Symbol

Min

Typ

Max

Unit

Test Conditions/Comments

LO PHASE

SYNCHRONIZATION

Initial Phase

Synchronization

Accuracy

0.9

ps

EXTERNAL LO INPUT

Input Frequency

f_EXTLO

1600

−6

12000

MHz

Input frequency must be 2× the

desired frequency for LO frequency

(f_LO)²≥ 1 GHz and 4× the desired f_LO

for f_LO< 1 GHz

50 Ω matching at the source

To ensure adequate quadrature error

correction

Input Signal Power

Input Signal Differential

Phase Balance

0

+6

15

dBm

Degrees

Input Signal Differential

Amplitude Balance

Input Signal Duty Cycle

Error

2

dB

%

CLOCK SYNTHESIZER

4915.2 MHz Sample Clock

Integrated Phase

Noise

0.69

°rms

1 kHz to 10 MHz, PLL bandwidth

optimized for low jitter

Spot Phase Noise

PLL bandwidth optimized for

integrated phase noise

100 kHz Offset

1 MHz Offset

10 MHz Offset

−96

−113

−140

dBc/Hz

3932.16 MHz Sample

Clock

Integrated Phase

Noise

0.89

°rms

1 kHz to 10 MHz, PLL bandwidth

optimized to minimize phase noise

at offsets > 200 kHz

Spot Phase Noise

PLL bandwidth optimized to minimize

phase noise at offsets > 200 kHz

100 kHz Offset

1 MHz Offset

10 MHz Offset

−92

−120

−143

dBc/Hz

REFERENCE CLOCK

(DEVCLK SIGNAL)

Frequency Range

Signal Level

(Differential)

15

0.2

1000

1.0

MHz

V p-p

AC-coupled, common-mode voltage

internally supplied; for best spurious

performance and to meet the specified

PLL performance parameters, use a

1 V p-p input clock

SYSTEM REFERENCE INPUTS SYSREF+,

SYSREF−

Logic Compliance

Differential Input Voltage

LVDS/LVPECL

800

400

1800

2.0

mV p-p

V

External 100 ꢀ termination

Input Common-Mode

Voltage

0.675

Input Resistance

(Differential)

Input Capacitance

(Differential)

18

1

kΩ

pF

Rev. E | Page 15 of 115

ADRV9010

Data Sheet

Parameter

AUXILIARY CONVERTERS

ADC

Symbol

Min

Typ

Max

Unit

Test Conditions/Comments

Resolution

Input Voltage

Minimum

Maximum

DAC

10

Bits

0.05

0.95

V

Resolution

12

Bits

Output Voltage:

AUXDAC_0

Minimum

Maximum

0.2

V

VDDA_1P8 −

0.25

Output Voltage:

AUXDAC_1 to

AUXDAC_7

Minimum

Maximum

0.1

V

VDDA_1P8 −

0.1

Drive Capability

10

mA

DIGITAL SPECIFICATIONS:

SINGLE-ENDED SIGNALS

Applies to the following pins:

GPIO_x, GPINTx, TXx_EN, RXx_EN,

ORX_CTRL_x, TEST_EN,

, SPI_EN,

RESET

SPI_CLK, SPI_DO, and SPI_DIO

Logic Inputs

Input Voltage

High Level

VIF × 0.65

−0.30

VIF + 0.18

VIF × 0.35

V

Low Level

Input Current

High Level

Low Level

−10

+10

μA

Logic Outputs

Output Voltage

High Level

VIF − 0.45

V

Low Level

0.45

V

Drive Capability

10

mA

DIGITAL SPECIFICATIONS:

DIFFERENTIAL SIGNALS

Applies to the SYNCINx and

SYNCOUTx pins

Logic Inputs

Input Voltage Range

Input Differential

Voltage Threshold

Receiver Differential

Input Impedance

825

−100

1675

+100

mV

Each differential input in the pair

Internal termination enabled

100

ꢀ

Rev. E | Page 16 of 115

Data Sheet

ADRV9010

Parameter

Logic Outputs

Output Voltage

High

Symbol

Min

Typ

Max

Unit

Test Conditions/Comments

1375

mV

Low

Differential

Offset

1025

225

1200

DIGITAL SPECIFICATIONS:

VDDA_1P8 REFERENCED

SIGNALS

Applies to the GPIO_ANA_x pin

Logic Inputs

Input Voltage

High Level

VDDA_1P8

× 0.65

−0.30

VDDA_1P8

+ 0.18

VDDA_1P8

× 0.35

V

Low Level

Input Current

High Level

Low Level

−10

+10

μA

Logic Outputs

Output Voltage

High Level

VDDA_1P8

− 0.45

V

Low Level

0.45

V

Drive Capability

10

mA

¹f_RFLOis the frequency of the RF LO synthesizer and f_AUXLOis the frequency of the auxiliary synthesizer.

²f_LOis the frequency of the internal local oscillator generator.

POWER SUPPLY SPECIFICATIONS

Table 2.

Parameter

Min

Typ Max

Unit Test Conditions/Comments

SUPPLY CHARACTERISTICS

Voltage range requirements must be met at each ball input for the respective

voltage supply rail

VDDA_1P0 Supply

VDIG_1P0 Supply

VDDA_1P3 Supply

VDDA_1P8 Supply

VIF Supply

0.95

1.235 1.3

1.71

1.0

1.05

1.365

1.89

V

1.8

Rev. E | Page 17 of 115

ADRV9010

Data Sheet

CURRENT CONSUMPTION

TDD Operation (Typical Values)

Table 3. TDD Mode: 4 Rx Channels Enabled, Maximum Gain

Supply (A)

Profile Conditions¹

1.0 V 1.3 V 1.8 V Total Average Power (W) 75% Tx, 25% Rx Average Power (W)

USE CASE 26 NONLINK SHARING (16 BITS)

491.52 MSPS Tx/ORx Data Rate

245.76 MSPS Rx Data Rate

1.750 2.197 0.241 5.048

1.570 2.184 0.271 4.907

1.409 2.210 0.245 4.731

5.456

5.491

5.134

245.76 MHz Device Clock

USE CASE 14 LINK SHARING (12 BITS)

491.52 MSPS Tx/ORx Data Rate

245.76 MSPS Rx Data Rate

245.76 MHz Device Clock

USE CASE 47 LINK SHARING (16 BITS)

491.52 MSPS Tx/ORx Data Rate

245.76 MSPS Rx Data Rate

245.76 MHz Device Clock

¹All current measurements made at room temperature without a heat sink.

Table 4. TDD Mode: 4 Tx and 1 ORx Channels Enabled, 0 dB Attenuation, Maximum Gain

Supply (A)

Profile Conditions¹

1.0 V 1.3 V 1.8 V Total Average Power (W)

75% Tx, 25% Rx Average Power (W)

USE CASE 26 NONLINK SHARING (16 BITS)

491.52 MSPS Tx/ORx Data Rate

245.76 MSPS Rx Data Rate

1.731 2.088 0.633 5.592

5.456

245.76 MHz Device Clock

USE CASE 14 LINK SHARING (12 BITS)

491.52 MSPS Tx/ORx Data Rate

245.76 MSPS Rx Data Rate

1.796 2.061 0.668 5.686

1.419 2.081 0.631 5.269

5.491

5.134

245.76 MHz Device Clock

USE CASE 47 LINK SHARING (16 BITS)

491.52 MSPS Tx/ORx Data Rate

245.76 MSPS Rx Data Rate

245.76 MHz Device Clock

¹All current measurements made at room temperature without a heatsink.

Rev. E | Page 18 of 115

Data Sheet

ADRV9010

DIGITAL INTERFACE AND TIMING SPECIFICATIONS

Table 5.

Parameter

Symbol

Min

Typ Max

Unit

Test Conditions/Comments

SPI TIMING

Write SPI_CLK Period

t_CP

t_MP

t_SC

t_HC

t_S

40

10

4

0

4

100

ns

SPI_CLK High Pulse Width

SPI_EN Setup to First SPI_CLK Rising Edge

Last SPI_CLK Falling Edge to SPI_EN Hold

SPI_DIO Data Input Setup to SPI_CLK

SPI_DIO Data Input Hold to SPI_CLK

t_H

t_CO

0

10

SPI_CLK Falling Edge to Output Data Delay (3- or

4-Wire Mode)

16

Bus Turnaround Time After Baseband Processor

Drives Last Address Bit

Bus Turnaround Time After ADRV9010 Drives Last

Address Bit

t_HZM

t_HZS

t_INT

t_H

0

t_CO

400

ns

Byte to Byte Delay Time

Pause duration between any two

bytes of the 3-byte operation

(write or read)

DIGITAL TIMING

TXx_EN Pulse Width¹

10

μs

RXx_EN Pulse Width¹

ORX_CTRL_x Pulse Width²

TXx_EN to Valid Data¹

RXx_EN to Valid Data¹

ORX_CTRL_x to Valid Data²

JESD204B/JESD204C DATA OUTPUT INTERFACE

Unit Interval

Data Rate per Channel (Nonreturn to Zero (NRZ))

Rise Time

2

3

UI

61.65

1000

17

1000

16220

ps

Mbps

ps

t_R

26

20% to 80% in 100 ꢀ load

AC-coupled

Fall Time

t_F

17

0

26

ps

V

mV

mA

ꢀ

Output Common-Mode Voltage

Termination Voltage = 1.0 V

Differential Output Voltage

Short-Circuit Current

Differential Termination Impedance

SYSREF_IN Signal Setup Time to DEVCLK Signal

SYSREF_IN Signal Hold Time to DEVCLK Signal

JESD204B/JES204C DATA INPUT INTERFACE

Unit Interval

Data Rate per Channel (NRZ)

Input Common-Mode Voltage

V_TT= 1.0 V

Differential Input Voltage

V_TTSource Impedance

V_CM

V_TT

V_DIFF

I_DSHORT

Z_RDIFF

t_S

1.8

1135

770

+100

120

735

360

−100

80

200

DC-coupled

466

100

ps

t_H

UI

61.65

1000

0.05

720

1000

16220

1.65

1200

750

ps

Mbps

V

mV

ꢀ

V_CM

AC-coupled

DC-coupled (not recommended)

V_DIFF

Z_TT

125

1.2

30

Differential Termination Impedance

V_TT

Z_RDIFF

80

106

120

ꢀ

AC-Coupled

DC-Coupled

1.27

1.14

1.33

1.26

V

¹Where x represents the channel number.

²Where x represents A, B, C, or D.

Rev. E | Page 19 of 115

ADRV9010

Data Sheet

ABSOLUTE MAXIMUM RATINGS

Table 6.

Table 7. Acceleration Factors for High Temperature Operation

Operating Junction Temperature (°C) Acceleration Factor (AF)

Parameter

Rating

125

120

115

110

105

100

95

3.75

2.44

1.57

1.00

0.63

0.39

0.24

0.14

VDDA_1P8 to VSSA

VDDA_1P3 to VSSA

VDDA_1P0, VDIG_1P0 to VSSD, VSSA

VIF Referenced Logic Inputs and

Outputs to VSSD

JESD204B Logic Outputs to VSSA

JESD204B Logic Inputs to VSSA

Input Current to Any Pin Except Supplies

Maximum Input Power into RF Ports

−0.3 V to +2.2 V

−0.2 V to +1.5 V

−0.2 V to +1.2 V

−0.3 V to VIF + 0.3 V

−0.3 V to VSER_1P0

−0.3 V to VDES_1P0

10 mA

See Table 8 for limits

vs. survival time

90

Table 8. Maximum Input Power into RF Ports vs. Lifetime

Lifetime

Junction Temperature Range¹

Storage Temperature Range

−40°C to +110°C

−65°C to +150°C

RF Port Input Power,

CW Signal (dBm)

7

10

20

23

25

Gain = −30 dB

Gain = 0 dB

>10 years

20,000 hours

14 hours

110 minutes

60 minutes

>10 years

>7 years

¹The maximum junction temperature for continuous operation is 110°C. See

the Junction Temperature section for more details.

Stresses at or above those listed under Absolute Maximum

Ratings may cause permanent damage to the product. This is a

stress rating only; functional operation of the product at these

or any other conditions above those indicated in the operational

section of this specification is not implied. Operation beyond the

maximum operating conditions for extended periods may

affect product reliability.

REFLOW PROFILE

The ADRV9010 reflow profile is in accordance with the JEDEC

JESD20 criteria for Pb-free devices. The maximum reflow

temperature is 260°C.

JUNCTION TEMPERATURE

THERMAL RESISTANCE

The maximum junction temperature for continuous operation

is 110°C. Although operation up to 125°C is supported,

specification compliance is only guaranteed up to 110°C. To

avoid a reduction in operating lifetime by operating above 110°C,

the device must operate at a temperature less than 110°C for a

period (t_UNITS) determined by the following equation:

Thermal resistance values specified in Table 9 are calculated

based on JEDEC specifications (unless specified otherwise) and

should be used in compliance with JESD51-12. Note that using

enhanced heat removal techniques (PCB, heat sink, air flow,

and so forth) improves thermal resistance.

θ_JAis the natural convection junction to ambient thermal

t

_{UNITS < 110}= (AF_{T > 110}− 1)/(1 − AF_{T < 110})

resistance measured in a one cubic foot sealed enclosure.

where AF_{T > 110}and AF_{T < 110}are acceleration factors obtained

from Table 7.

θ_JCis the junction to case thermal resistance.

Table 9. Thermal Resistance Values

For example, if the device operates at 125°C for 1 hour, expected

device lifetime is maintained if the device operates at 100°C for

4.5 hours to offset the time operating above 110°C.

Package Type

θ_JA

θ_JC

Unit

BC-289-3

14.8

0.03

(°C/W)

ESD CAUTION

Rev. E | Page 20 of 115

Data Sheet

ADRV9010

PIN CONFIGURATION AND FUNCTION DESCRIPTIONS

ADRV9010

TOP VIEW

(Not to Scale)

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

VTXLO_

IP3

VRXLO_

IP3

A

B

C

D

E

F

VSSA

TX3+

TX3–

VSSA

TX2+

TX2–

VSSA

VANA3_

1P8

VAUXVCO

_1P0

VANA2_

1P8

RX3–

RX3+

VSSA

NIC

VSSA

RX2+

RX2–

VSSA

GPIO_

ANA_7

GPIO_ VAUXSYN

ANA_6

VAUXVCO GPIO_

_1P3

GPIO_

ANA_0

VSSA DEVCLK+ DEVCLK– VSSA

VSSA SYSREF+ SYSREF– VSSA

VSSA

ORX1–

VSSA

ORX2–

VSSA

RBIAS

_1P3

ANA_1

VANA2_

1P3

VANA1_

1P3

VSSA

ORX3+

VSSA

ORX4+

VSSA

ORX1+

VSSA

AUXADC

_3

EXT_

LO2–

EXT_

LO1+

AUXADC

_1

VSSA

ORX3–

VSSA

TX3_EN GPIO_11 GPIO_9 GPIO_3 TX2_EN

VSSA

AUXADC

_2

EXT_

LO2+

ORX_

CTRL_C

ORX_

CTRL_B

EXT_

LO1–

AUXADC

_0

GPIO_12 GPIO_10 GPIO_4

VRFVCO2

_1P3

VRFVCO2

_1P0

VRFVCO1

_1P0

VRFVCO1

_1P3

G

H

J

VSSA

RX4–

RX4+

VSSA

RX3_EN GPIO_13 VDIG_1P0 GPIO_5 RX2_EN

VSSA

RX1+

RX1–

VSSA

VCONV2

_1P8

VCONV1

_1P8

VSSA

GPIO_17 GPIO_14

VSSD

GPIO_6 GPIO_0

VSSA

VCONV2

_1P3

VRFSYN2

_1P3

VRFSYN1

_1P3

VCONV1

_1P3

RX4_EN GPIO_15 VDIG_1P0 GPIO_7 RX1_EN

VCONV2

_1P0

VCONV1

_1P0

K

L

VSSA

ORX4–

VSSA

GPIO_18 GPIO_16

ORX_

VSSD

GPIO_8 GPIO_1

ORX_

VSSA

ORX2+

VSSA

GPIO_

ANA_5

GPIO_

ANA_4

GPIO_

ANA_2

GPIO_

ANA_3

VSSA

SPI_DIO VDIG_1P0 SPI_EN

VSSA

CTRL_D

CTRL_A

M

N

P

R

T

VSSA

TX4–

TX4+

VSSA

TX4_EN SPI_DO

VSSD

VIF

SPI_CLK TX1_EN

VSSA

TX1+

TX1–

VSSA

VANA4

_1P8

VCLKVCO

_1P3

SYNC

OUT2+

SYNC

OUT2–

VANA1

_1P8

SYNCIN3+ GPINT2 GPINT1

GPIO_2 SYNCIN1+ SYNCIN1–

RESET

TEST_EN

VSSA

VDES

_1P0

VDES

_1P0

VCLKVCO

_1P0

VJVCO

_1P8

SYNC

OUT1+

VSSA

SYNCIN3– SYNCIN2+ SYNCIN2– VSSA

VTT_DES

VSSA

VSER

_1P0

VSER

_1P0

VCLKSYN

_1P3

VJSYN

_1P0

SYNC

OUT1–

VSSA

NIC

VSSA

SERD

OUTD+

SERD

OUTD–

SERD

OUTC+

SERD

OUTC–

SERD

OUTB+

SERD

OUTB–

SERD

OUTA+

SERD

OUTA–

SERD

IND–

SERD

IND+

SERD

INC+

SERD

INC–

SERD

INB–

SERD

INB+

SERD

INA+

SERD

INA–

VSSA

SERD

OUTH+

SERD

OUTH–

SERD

OUTG+

SERD

OUTG–

SERD

OUTF+

SERD

OUTF–

SERD

OUTE+

SERD

OUTE–

SERD

INH–

SERD

INH+

SERD

ING+

SERD

ING–

SERD

INF–

SERD

INF+

SERD

INE+

SERD

INE–

U

AUXILIARY

ANALOG GROUND

DIGITAL GROUND

ANALOG POWER

DIGITAL POWER

LVDS SERDES CONTROLS

SERDES INPUTS/OUTPUTS

DIFFERENTIAL SYSREF SIGNAL

NOT INTERNALLY CONNECTED

ADC INPUTS

ANALOG

INPUTS/OUTPUTS

DIGITAL

INPUTS/OUTPUTS

ANALOG GPIO

SPI BUS

Figure 2. Pin Configuration

Rev. E | Page 21 of 115

ADRV9010

Data Sheet

Table 10. Pin Function Descriptions

Ball No.

Type¹Mnemonic

Description

A1 to A3, A6, A8, A10 to A12, A15 to A17, B2, B3, B5 to B10,

B12, B13, B15, B16, C2, C7, C10, C14, C16, D1, D2, D4 to D7,

D10 to D14, D16, D17, E3, E6, E12, E15, F3 to F6, F12 to F15,

G1, G2, G4, G6, G12, G14, G16, G17, H2, H4 to H6, H12 to H14,

H16, J2, J4, J6, J12, J14, J16, K1, K2, K4 to K6, K12 to K14, K16,

K17, L3, L6, L12, L15, M1 to M6, M12 to M17, N3, N4, P2 to P4,

P9, P16, R1, R2, R5, R6, R8, R10, R12 to R14, R16, R17, T9, U9

I

VSSA

Analog Grounds.

A4, A5

O

TX3+, TX3−

Differential Outputs for Transmitter Channel 3.

Do not connect if unused.

A7

A9

A13, A14

I

O

VTXLO_1P3

VRXLO_1P3

TX2+, TX2−

1.3 V Supply Input.

Differential Outputs for Transmitter Channel 2.

Do not connect if unused.

B1, C1

I

RX3−, RX3+

Differential Inputs for Receiver Channel 3.

Connect to VSSA if unused.

B4

I

VANA3_1P8

1.8 V Supply Input.

B11

O

VAUXVCO_1P0

1.0 V Internal Supply Node. Bypass Pin B11

with a 4.7 μF capacitor.

B14

B17, C17

I

VANA2_1P8

RX2+, RX2−

1.8 V Supply Input.

Differential Inputs for Receiver Channel 2.

Connect to VSSA if unused.

C3, R11

N/A

I/O

NIC

Not Internally Connected. Pin C3 and R11

must remain disconnected.

C4, C5, C12, C13, L1, L2, L17, L16

GPIO_ANA_7 to

GPIO_ANA_0

General-Purpose Inputs and Outputs. The

GPIO pins are referenced to 1.8 V but can

also function as auxiliary DAC outputs. If

unused, these pins can be connected to

VSSA with a 10 kΩ resistor or configured as

outputs, driven low, and left disconnected.

C6

I

VAUXSYN_1P3

DEVCLK+, DEVCLK− Device Clock Differential Inputs.

VAUXVCO_1P3

RBIAS

1.3 V Supply Input.

C8, C9

C11

C15

1.3 V Supply Input.

Bias Resistor Connection. Pin C15 generates

an internal current based on an external 1%

resistor. Connect a 4.99 kΩ resistor between

C15 and analog ground (VSSA).

D3

D8, D9

I

VANA2_1P3

SYSREF+, SYSREF−

1.3 V Supply Input.

LVDS System Reference Clock Inputs for the

Serializer/Deserializer (SERDES) Interface.

Connect a 100 Ω termination between these

pins.

D15

E1

I

VANA1_1P3

AUXADC_3

1.3 V Supply Input.

Auxiliary ADC 3 Input. Do not connect if

unused.

E2, F2

I/O

EXT_LO2−,

EXT_LO2+

Differential External LO Input/Output 2. If

used for the external LO input, the input

frequency must be 2× the desired carrier

frequency. Do not connect if unused.

E4, E5

E7

I

ORX3+, ORX3−

TX3_EN

Differential Inputs for Observation Receiver

Channel 3. Connect to VSSA if unused.

Enable Input for Transmitter Channel 3.

Connect to VSSA if unused.

Rev. E | Page 22 of 115

Data Sheet

ADRV9010

Ball No.

Type¹Mnemonic

Description

E8 to E10, F8 to F10, G8, G10, H7, H8, H10, H11, J8, J10, K7,

K8, K10, K11, N11

I/O

GPIO_0 to GPIO_18

General-Purpose Digital Inputs and Outputs.

See Figure 2 to match the ball location to

the GPIO_x signal name. If unused, these

pins can be connected to VSSA with a 10 kΩ

resistor or configured as outputs, driven low,

and left disconnected.

E11

I

TX2_EN

Enable Input for Transmitter Channel 2.

Connect to VSSA if unused.

E13, E14

E16, F16

I

ORX1+, ORX1−

Differential Inputs for Observation Receiver

Channel 1. Connect to VSSA if unused.

Differential External LO Input/Output 1. If

used for the external LO input, the input

frequency must be 2× the desired carrier

frequency. Do not connect if unused.

I/O

EXT_LO1+,

EXT_LO1−

E17

I

AUXADC_1

AUXADC_2

Auxiliary ADC 1 Input. Do not connect if

unused.

Auxiliary ADC2 Input. Do not connect if

unused.

These pins determines the active ORX_x

path. Connect to VSSA directly or with a

pull-down resistor if unused.

F1

F7, F11, L7, L11

ORX_CTRL_C,

ORX_CTRL_B,

ORX_CTRL_D,

ORX_CTRL_A

F17

I

AUXADC_0

Auxiliary ADC0 Input. Do not connect if

unused.

G3

G5

I

O

VRFVCO2_1P3

VRFVCO2_1P0

1.3 V Supply Input.

1.0 V Internal Supply Node. Bypass this pin

with a 4.7 μF capacitor.

G7

I

RX3_EN

Enable Input for Receiver Channel 3.

Connect to VSSA if unused.

G9, J9, L9

G11

I

VDIG_1P0

RX2_EN

1.0 V Digital Supply Input.

Enable Input for Receiver Channel 2.

Connect to VSSA if unused.

G13

O

VRFVCO1_1P0

1.0 V Internal Supply Node. Bypass this pin

with a 4.7 μF capacitor.

G15

H1, J1

I

VRFVCO1_1P3

RX4−, RX4+

1.3 V Supply Input.

Differential Inputs for Receiver Channel 4.

Connect to VSSA if unused.

H3

H9, K9, M9

H15

I

VCONV2_1P8

VSSD

VCONV1_1P8

RX1+, RX1−

1.8 V Supply Input.

Digital Ground.

1.8 V Supply Input.

Differential Inputs for Receiver Channel 1.

Connect to VSSA if unused.

H17, J17

J3

J5

J7

I

VCONV2_1P3

VRFSYN2_1P3

RX4_EN

1.3 V Supply Input.

Enable Input for Receiver Channel 4.

Connect to VSSA if unused.

J11

I

RX1_EN

Enable Input for Receiver Channel 1.

Connect to VSSA if unused.

J13

J15

K3

I

O

VRFSYN1_1P3

VCONV1_1P3

VCONV2_1P0

1.3 V Supply Input.

1.0 V Internal Supply Node. Bypass this pin

with a 4.7 μF capacitor.

K15

O

VCONV1_1P0

1.0 V Internal Supply Node. Bypass this pin

with a 4.7 μF capacitor.

Rev. E | Page 23 of 115

ADRV9010

Data Sheet

Ball No.

Type¹Mnemonic

Description

L4, L5

I

ORX4+, ORX4−

Differential Inputs for Observation Receiver

Channel 4. Connect to VSSA if unused.

L8

I/O

SPI_DIO

Serial Data Input/Output. Pin L8 is a serial data

input only when in 4-wire mode. When L8 is in

3-wire mode, it is a serial data input/output.

L10

L13, L14

I

SPI_EN

ORX2+, ORX2−

Serial Data Bus Chip Select. Active low.

Differential Inputs for Observation Receiver

Channel 2. Connect to VSSA if unused.

M7

I

TX4_EN

Enable Input for Transmitter Channel 4.

Connect to VSSA if unused.

M8

M10

M11

O

I

SPI_DO

SPI_CLK

TX1_EN

Serial Data Output.

Serial Data Bus Clock Input.

Enable Input for Transmitter Channel 1.

Connect to VSSA if unused.

N1, P1

O

TX4−, TX4+

Differential Outputs for Transmitter Channel 4.

Do not connect if unused.

N2

N5

N6, P6

I

VANA4_1P8

VCLKVCO_1P3

SYNCIN3+,

SYNCIN3−

1.8 V Supply Input.

1.3 V Supply Input.

Low Voltage Differential Signal (LVDS)

Synchronization Signal Input 3. Connect to

VSSA if unused.

N7

N8

O

GPINT2

GPINT1

General-Purpose Interrupt Output 2. Do not

connect if unused.

General-Purpose Interrupt Output 1. Do not

connect if unused.

N9

N10

I

VIF

RESET

1.8 V Interface Supply Input.

Active Low Chip Reset.

N12, N13

SYNCIN1+,

SYNCIN1−

LVDS Synchronization Signal Input 1.

Connect to VSSA if unused.

N14, N15

O

SYNCOUT2+,

SYNCOUT2−

LVDS Synchronization Signal Output 2. Do

not connect if unused.

N16

N17, P17

I

O

VANA1_1P8

TX1+, TX1−

1.8 V Supply Input.

Differential Outputs for Transmitter Channel 1.

Do not connect if unused.

P5

O

I

VCLKVCO_1P0

1.0 V Internal Supply Node. Bypass this pin

with a 4.7 μF capacitor.

LVDS Synchronization Signal Input 2.

Connect to VSSA if unused.

Test Input for JTAG Boundary Scan. Pull high

to enable boundary scan, and tie to VSSA if

unused.

P7, P8

P10

SYNCIN2+,

SYNCIN2−

TEST_EN

I

P11

P12, P13

P14

I

VJVCO_1P8

VDES_1P0

VTT_DES

1.8 V Supply Input.

1.0 V Analog Supply Input.

P15, R15

O

SYNCOUT1+,

SYNCOUT1−

LVDS Synchronization Signal Output 1. Do

not connect if unused.

R3, R4

R7

R9

I

VSER_1P0

VCLKSYN_1P3

VJSYN_1P0

1.0 V Analog Supply Input.

1.3 V Supply Input.

1.0 V Analog Supply Input.

Rev. E | Page 24 of 115

Data Sheet

ADRV9010

Ball No.

Type¹Mnemonic

Description

T1, T2

O

I

SERDOUTD+,

SERDOUTD−

SERDOUTC+,

SERDOUTC−

SERDOUTB+,

SERDOUTB−

SERDOUTA+,

SERDOUTA−

SERDIND−,

SERDIND+

SERDINC+,

SERDINC−

SERDINB−,

SERDINB+

SERDINA+,

SERDINA−

SERDOUTH+,

SERDOUTH−

SERDOUTG+,

SERDOUTG−

SERDOUTF+,

SERDOUTF−

SERDOUTE+,

SERDOUTE−

SERDINH−,

SERDINH+

SERDING+,

SERDING−

SERDINF−,

SERDINF+

SERDINE+,

SERDINE−

SERDES Differential Output D. Do not

connect if unused.

SERDES Differential Output C. Do not

connect if unused.

SERDES Differential Output B. Do not

connect if unused.

SERDES Differential Output A. Do not

connect if unused.

SERDES Differential Input D. Do not connect

if unused.

SERDES Differential Input C. Do not connect

if unused.

SERDES Differential Input B. Do not connect

if unused.

SERDES Differential Input A. Do not connect

if unused.

SERDES Differential Output H. Do not

connect if unused.

SERDES Differential Output G. Do not

connect if unused.

SERDES Differential Output F. Do not

connect if unused.

SERDES Differential Output E. Do not

connect if unused.

SERDES Differential Input H. Do not connect

if unused.

SERDES Differential Input G. Do not connect

if unused.

SERDES Differential Input F. Do not connect

if unused.

SERDES Differential Input E. Do not connect

if unused.

T3, T4

T5, T6

T7, T8

T10, T11

T12, T13

T14, T15

T16, T17

U1, U2

I

O

I

U3, U4

U5, U6

U7, U8

U10, U11

U12, U13

U14, U15

U16, U17

I

¹I is input, O is output, N/A is not applicable, and I/O is input/output.

Rev. E | Page 25 of 115

ADRV9010

Data Sheet

TYPICAL PERFORMANCE CHARACTERISTICS

800 MHz BAND

The temperature settings refer to the die temperature. All LO frequencies set to 800 MHz, unless otherwise noted.

7.0

6.5

6.0

5.5

5.0

4.5

4.0

3.5

3.0

–100

–110

–120

–130

–140

–150

–160

–170

–180

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+110°C

+25°C

–40°C

650

700

750

800

850

900

950

1000

0

5

10

15

20

TRANSMITTER LO FREQUENCY (MHz)

TRANSMITTER ATTENUATION (dB)

Figure 6. Transmitter Noise vs. Transmitter Attenuation, 50 MHz Offset

Figure 3. Transmitter CW Output Power vs. Transmitter LO Frequency,

10 MHz Offset, 0 dB Attenuation

1.0

0

SIGNAL

NOISE FLOOR

+110°C

0.9

0.8

–10

+25°C

–40°C

–20

–30

–40

–50

–60

–70

–80

–90

–100

0.7

0.6

0.5

0.4

0.3

0.2

0.1

0

–0.1

–250 –200 –150 –100 –50

0

50

100 150 200 250

BASEBAND OFFSET FREQUENCY (MHz)

FREQUENCY (MHz)

Figure 4. Transmitter Output Power Spectrum, Tx1, 5 MHz LTE,

Figure 7. Transmitter Pass Band Flatness vs. Baseband Offset Frequency

10 MHz Offset, −10 dBFS RMS, 1 MHz Resolution Bandwidth, T = 25°C

–40

+110°C

+25°C

–40°C

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

–45

–50

–55

–60

–65

–70

–75

–80

–50

–60

–70

–80

–90

–100

–100 –80 –60 –40 –20

0

20

40

60

80

100

0

5

10

15

20

BASEBAND OFFSET FREQUENCY (MHz)

TRANSMITTER ATTENUATION (dB)

Figure 5. Transmitter Image Rejection vs. Baseband Offset Frequency,

0 dB Attenuation, QEC Tracking Enabled

Figure 8. Adjacent Channel Power Level vs. Transmitter Attenuation,

−10 MHz Baseband Offset, 20 MHz LTE, PAR = 12 dB,

Loop Filter Bandwidth = 50 kHz, Loop Filter Phase Margin = 40°

Rev. E | Page 26 of 115

Data Sheet

ADRV9010

–40

–45

–50

–55

–60

–65

–70

–75

0.05

0.04

0.03

0.02

0.01

0

+110°C

+25°C

–40°C

–0.01

–0.02

–0.03

–0.04

–0.05

+110°C

+25°C

–40°C

–80

0

5

10

15

20

0

4

8

12

16

20

24

28

32

TRANSMITTER ATTENUATION (dB)

Figure 9. Adjacent Channel Power Level vs. Transmitter Attenuation,

90 MHz Baseband Offset, 20 MHz LTE, PAR = 12 dB,

Figure 12. Transmitter Attenuator Step Error vs. Transmitter Attenuation,

10 MHz Offset

Loop Filter Bandwidth = 50 kHz, Loop Filter Phase Margin = 40°

–60

–42

+110°C, UPPER HD2

+25°C, UPPER HD2

–40°C, UPPER HD2

+110°C, LOWER HD2

+25°C, LOWER HD2

–40°C, LOWER HD2

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

–70

–80

–44

–46

–48

–50

–52

–90

–100

–110

0

2

4

6

8

10

12

14

16

18

20

0

5

10

15

20

TRANSMITTER ATTENUATION (dB)

Figure 13. Transmitter Error Vector Magnitude vs. Transmitter Attenuation,

20 MHz LTE Signal Centered at LO Frequency, Sample Rate = 491.52 MSPS, QEC

Tracking Enabled, Loop Filter Bandwidth = 50 kHz, Loop Filter Phase Margin = 40°

Figure 10. Transmitter Second Harmonic Distortion (HD2) vs.

Transmitter Attenuation, 10 MHz Offset

–60

45

40

35

30

25

20

15

10

5

+110°C, UPPER HD3

+25°C, UPPER HD3

–40°C, UPPER HD3

+110°C, LOWER HD3

+25°C, LOWER HD3

–40°C, LOWER HD3

–70

–80

–90

–100

–110

–120

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

0

–5

–10

0

2

4

6

8

10

12

14

16

18

20

0

4

8

12

16

20

24

28

32

TRANSMITTER ATTENUATION (dB)

Figure 11. Transmitter Third Harmonic Distortion (HD3) vs. Transmitter

Attenuation, 10 MHz Offset

Figure 14. Transmitter OIP3, 2f1 − f2 vs. Transmitter Attenuation,

15 dB Digital Backoff per Tone, f1 = 50.5 MHz, f2 = 55.5 MHz

Rev. E | Page 27 of 115

ADRV9010

Data Sheet

45

40

35

30

25

20

15

10

5

50

45

40

35

30

25

20

15

10

5

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+110°C, Tx1

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

0

–5

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–10

0

10

0

4

8

12

16

20

24

28

32

30

50

70

90

110

130

150

170

190

TRANSMITTER ATTENUATION (dB)

f1 BASEBAND OFFSET TONE FREQUENCY (MHz)

Figure 15. Transmitter OIP3, 2f2 − f1 vs. Transmitter Attenuation,

15 dB Digital Backoff per Tone, f1 = 50.5 MHz, f2 = 55.5 MHz

Figure 18. Transmitter OIP3, 2f1 + f2 vs. f1 Baseband Offset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Backoff per Tone

50

45

40

35

30

25

20

15

50

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

45

40

35

30

25

20

15

10

5

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

10

5

0

10

0

10

30

50

70

90

110

130

150

170

190

30

50

70

90

110

130

150

170

190

f1 BASEBAND OFFSET TONE FREQUENCY (MHz)

Figure 16. Transmitter OIP3, 2f1 − f2 vs. f1 Baseband Offset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Backoff per Tone

Figure 19. Transmitter OIP3, 2f2 + f1 vs. f1 Baseband Offset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Backoff per Tone

50

45

40

35

30

25

20

15

120

110

100

90

80

70

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

10

5

Tx1 TO Tx2

Tx2 TO Tx1

Tx3 TO Tx1

Tx4 TO Tx1

Tx1 TO Tx3

Tx2 TO Tx3

Tx3 TO Tx4

Tx4 TO Tx4

Tx1 TO Tx4

Tx2 TO Tx4

Tx3 TO Tx4

Tx4 TO Tx3

60

50

0

10

30

50

70

90

110

130

150

170

190

800

850

900

950

1000

f1 BASEBAND OFFSET TONE FREQUENCY (MHz)

TRANSMITTER LO FREQUENCY (MHz)

Figure 17. Transmitter OIP3, 2f2 − f1 vs. f1 Baseband Offset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Backoff per Tone

Figure 20. Transmitter to Transmitter Isolation vs. Transmitter LO Frequency

Rev. E | Page 28 of 115

Data Sheet

ADRV9010

130

120

110

100

90

50

45

40

35

30

25

20

15

10

5

Tx1 TO Rx1

Tx2 TO Rx1

Tx3 TO Rx1

Tx4 TO Rx1

Tx1 TO Rx2

Tx2 TO Rx2

Tx3 TO Rx2

Tx4 TO Rx2

80

70

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

Tx1 TO Rx3

Tx2 TO Rx3

Tx3 TO Rx3

Tx4 TO Rx3

Tx1 TO Rx4

Tx2 TO Rx4

Tx3 TO Rx4

Tx4 TO Rx4

60

50

800

0

850

900

950

1000

0

5

10

15

20

25

30

RECEIVER LO FREQUENCY (MHz)

RECEIVER ATTENUATION (dB)

Figure 21. Transmitter to Receiver Isolation vs. Receiver LO Frequency

Figure 24. Receiver Integrated Noise Figure vs. Receiver Attenuation,

200 MHz Bandwidth, Sample Rate = 245.76 MSPS,

Integration Bandwidth = 500 kHz to 100 MHz

140

130

120

110

100

90

25

20

15

10

Tx1 TO ORx1

Tx2 TO ORx1

Tx3 TO ORx1

Tx4 TO ORx1

Tx1 TO ORx2

Tx2 TO ORx2

Tx3 TO ORx2

Tx4 TO ORx2

80

70

60

50

+110°C

+25°C

–40°C

5

Tx1 TO ORx3

Tx1 TO ORx4

Tx2 TO ORx4

Tx3 TO ORx4

Tx4 TO ORx4

Tx2 TO ORx3

Tx3 TO ORx3

Tx4 TO ORx3

0

800

850

900

950

1000

–100 –80 –60 –40 –20

0

20

40

60

80

100

TRANSMITTER LO FREQUENCY (MHz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 22. Transmitter to Observation Receiver Isolation vs.

Transmitter LO Frequency

Figure 25. Receiver Integrated Noise Figure vs. Baseband Offset Frequency,

200 MHz Bandwidth, Sample Rate = 245.76 MSPS, Integrated in 200 kHz Steps

–40

120

+110°C

+25°C

–40°C

110

100

90

–50

–60

–70

80

–80

70

Rx1 TO Rx2

Rx2 TO Rx1

Rx3 TO Rx1

Rx4 TO Rx1

Rx1 TO Rx3

Rx2 TO Rx3

Rx3 TO Rx2

Rx4 TO Rx2

Rx1 TO Rx4

Rx2 TO Rx4

Rx3 TO Rx4

Rx4 TO Rx3

–90

60

–100

50

800

650

700

750

800

850

900

950

1000

850

900

950

1000

RECEIVER LO FREQUENCY (MHz)

Figure 23. Receiver to Receiver Isolation vs. Receiver LO Frequency

Figure 26. Receiver LO Leakage vs. Receiver LO Frequency,

Attenuation = 0 dB, Sample Rate = 245.76 MSPS

Rev. E | Page 29 of 115

ADRV9010

Data Sheet

0.5

0.4

20

15

10

5

0.3

0.2

0.1

0

–0.1

–0.2

–0.3

–0.4

–0.5

+110°C

+25°C

–40°C

–5

–10

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

–15

0

–100 –80 –60 –40 –20

0

20

40

60

80

100

5

10

15

20

25

BASEBAND OFFSET FREQUENCY (MHz)

RECEIVER ATTENUATION (dB)

Figure 30. Normalized Receiver Flatness vs. Baseband Offset Frequency,

−5 dBFS Input Signal, 0 dB Attenuation

Figure 27. Receiver Gain vs. Receiver Attenuation, 20 MHz Offset,

200 MHz Bandwidth, Sample Rate = 245.76 MSPS

–40

20

19

18

17

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

–50

–60

–70

–80

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

16

15

–90

–100

–100 –80 –60 –40 –20

0

20

40

60

80

100

650

700

750

800

850

900

950

1000

BASEBAND OFFSET FREQUENCY (MHz)

RECEIVER LO FREQUENCY (MHz)

Figure 28. Receiver Gain vs. Receiver LO Frequency, 10 MHz Offset,

200 MHz Bandwidth, Sample Rate = 245.76 MSPS

Figure 31. Receiver Image vs. Baseband Offset Frequency, Tracking Calibration

Active, Sample Rate = 245.76 MSPS, −5 dBFS Input Signal

–40

0.20

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

0.15

0.10

0.05

0

–50

–60

–70

–0.05

–0.10

–0.15

–0.20

–80

–90

–100

0

5

10

15

20

25

0

5

10

15

20

25

30

RECEIVER ATTENUATION (dB)

Figure 32. Receiver Image vs. Receiver Attenuation, 20 MHz Offset, Tracking

Calibration Active, Sample Rate = 245.76 MSPS, −5 dBFS Input Signal

Figure 29. Receiver Gain Step Error vs. Receiver Attenuation,

20 MHz Offset, −5 dBFS Input Signal

Rev. E | Page 30 of 115

Data Sheet

ADRV9010

–40

–50

–60

–70

–80

–90

–100

–40

–50

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

–60

–70

–80

–90

–100

–110

–120

–110

0

5

10

15

20

25

–40

–30

–20

–10

0

10

20

30

40

RECEIVER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 33. Receiver DC Offset vs. Receiver Attenuation, 20 MHz Offset,

−5 dBFS Input Signal

Figure 36. Receiver HD3, Left Side vs. Baseband Offset Frequency,

−5 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

–40

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

–50

–60

–50

–60

–70

–80

–90

–100

–110

–120

–100

–110

–120

–60

–40

–20

0

20

40

60

–40

–30

–20

–10

0

10

20

30

40

BASEBAND OFFSET FREQUENCY (MHz)

Figure 34. Receiver HD2, Left Side vs. Baseband Offset Frequency,

−5 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

(HD2 Canceller Not Enabled)

Figure 37. Receiver HD3, Right Side vs. Baseband Offset Frequency,

−5 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

–40

90

85

80

75

70

65

60

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

–50

–60

–70

–80

–90

–100

–110

–120

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

55

50

–60

–40

–20

0

20

40

60

805

815

825

TONE 2 FREQUENCY (MHz)

835

845

BASEBAND OFFSET FREQUENCY (MHz)

Figure 35. Receiver HD2, Right Side vs. Baseband Offset Frequency,

−5 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

(HD2 Canceller Not Enabled)

Figure 38. Receiver IIP2, f1 + f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Rev. E | Page 31 of 115

ADRV9010

Data Sheet

90

85

80

75

70

65

60

55

50

90

85

80

75

70

65

60

55

50

45

40

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

805

815

825

835

845

855

865

875

885

895

0

5

10

15

20

TONE 2 FREQUENCY (MHz)

RECEIVER ATTENUATION (dB)

Figure 39. Receiver IIP2, f1 − f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 42. Receiver IIP2, f1 + f2 vs. Receiver Attenuation,

Both Tones at −11 dBFS, f1 = 92 MHz, f2 = 2 MHz

90

100

95

90

85

80

75

70

65

60

85

80

75

70

65

60

55

50

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

10

20

30

40

50

60

70

80

90

0

5

10

15

20

TWO-TONE FREQUENCY SPACING (MHz)

RECEIVER ATTENUATION (dB)

Figure 40. Receiver IIP2, f1 + f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Figure 43. Receiver IIP2, f1 − f2 vs. Receiver Attenuation,

Both Tones at −11 dBFS, f1 = 92 MHz, f2 = 2 MHz

85

80

75

70

65

60

40

35

30

25

20

15

10

5

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

55

50

0

10

20

30

40

50

60

70

80

90

805

810

815

TONE 2 FREQUENCY (MHz)

820

825

TWO-TONE FREQUENCY SPACING (MHz)

Figure 41. Receiver IIP2, f1 − f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Figure 44. Receiver IIP3, 2f1 + f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Rev. E | Page 32 of 115

Data Sheet

ADRV9010

40

35

30

25

20

15

10

5

35

30

25

20

15

10

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

0

805

810

815

TONE 2 FREQUENCY (MHz)

820

825

10

15

20

25

30

35

40

TWO-TONE FREQUENCY SPACING (MHz)

Figure 45. Receiver IIP3, 2f2 + f1 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 48. Receiver IIP3, 2f1 + f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

40

35

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

35

30

25

20

15

10

5

30

25

20

15

10

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

0

805

815

825

835

845

855

865

875

885

895

10

20

30

40

50

60

70

80

90

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 46. Receiver IIP3, 2f1 − f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 49. Receiver IIP3, 2f2 + f1 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

40

35

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

35

30

25

20

15

10

5

30

25

20

15

10

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

0

805

815

825

835

845

855

865

875

885

895

10

15

20

25

30

35

40

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 47. Receiver IIP3, 2f2 − f1 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 50. Receiver IIP3, 2f1 − f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Rev. E | Page 33 of 115

ADRV9010

Data Sheet

35

30

25

20

15

10

–80

–90

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

–100

–110

–120

–130

–140

–150

–160

–170

10

20

30

40

50

60

70

80

90

100

1k

10k

100k

1M

10M

FREQUENCY OFFSET (Hz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 54. LO Phase Noise vs. Frequency Offset, Loop Bandwidth = 600 kHz,

Phase Margin = 60°

Figure 51. Receiver IIP3, 2f2 − f1 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

50

–20

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

45

40

35

30

25

20

15

10

5

–25

–30

–35

–40

–45

–50

0

5

10

15

20

–60 –55 –50 –45 –40 –35 –30 –25 –20 –15 –10 –5

0

OBSERVATION RECEIVER ATTENUATION (dB)

RECEIVER INPUT POWER (dBm)

Figure 55. Observation Receiver Integrated Noise Figure vs. Observation

Receiver Attenuation, 20 MHz Offset, 450 MHz Bandwidth,

Sample Rate = 491.52 MSPS, Integration Bandwidth = 500 kHz to 100 MHz

Figure 52. Receiver Error Vector Magnitude vs. Receiver Input Power,

20 MHz LTE Signal Centered at LO Frequency, Sample Rate = 245.76 MSPS,

Loop Filter Bandwidth = 50 kHz, Loop Filter Phase Margin = 40°

35

30

25

20

15

–80

–90

–100

–110

–120

–130

–140

–150

–160

–170

10

5

+110°C

+25°C

–40°C

0

–250

100

1k

10k

100k

1M

10M

–150

–50

50

150

250

FREQUENCY OFFSET (Hz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 53. LO Phase Noise vs. Frequency Offset, Loop Bandwidth = 50 kHz,

Phase Margin = 85°

Figure 56. Observation Receiver Integrated Noise Figure vs. Baseband Offset

Frequency, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS,

Integrated in 200 kHz Steps

Rev. E | Page 34 of 115

Data Sheet

ADRV9010

–40

–50

–60

–70

–80

–90

–100

0.20

0.15

0.10

0.05

0

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

–0.05

–0.10

–0.15

–0.20

+110°C

+25°C

–40°C

650

700

750

800

850

900

950

1000

0

5

10

15

20

25

30

OBSERVATION RECEIVER LO FREQUENCY (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 57. Observation Receiver LO Leakage vs. Observation Receiver

LO Frequency, 0 dB Attenuation, Sample Rate = 491.52 MSPS

Figure 60. Observation Receiver Gain Step Error vs. Observation Receiver

Attenuation, 20 MHz Offset, −5 dBFS Input Signal

20

15

10

5

0.6

0.4

0.2

0

–0.2

–5

+110°C

+25°C

–40°C

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

–0.4

–10

–15

–0.6

0

5

10

15

20

25

30

–220 –180 –140 –100 –60 –20 20

60 100 140 180 220

OBSERVATION RECEIVER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 58. Observation Receiver Gain vs. Observation Receiver Attenuation,

20 MHz Offset, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS

Figure 61. Normalized Observation Receiver Flatness vs. Baseband Offset

Frequency, −25 dBm Input Signal, 0 dB Attenuation

20

19

18

17

–40

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

–50

–60

–70

–80

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

16

–90

15

650

–100

700

750

800

850

900

950

1000

–225 –175 –125 –75

–25

25

75

125

175

225

OBSERVATION RECEIVER LO FREQUENCY (MHz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 59. Observation Receiver Gain vs. Observation Receiver LO Frequency,

450 MHz Bandwidth, Sample Rate = 491.52 MSPS

Figure 62. Observation Receiver Image vs. Baseband Offset Frequency,

Tracking Calibration Active, Sample Rate = 491.52 MSPS

Rev. E | Page 35 of 115

ADRV9010

Data Sheet

–40

–50

–60

–70

–80

–90

–40

–50

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

–60

–70

–80

–90

–100

–110

–120

–100

0

5

10

15

20

25

30

–60

–40

–20

0

20

40

60

OBSERVATION RECEIVER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 63. Observation Receiver Image vs. Observation Receiver Attenuation,

20 MHz Offset, Tracking Calibration Active, Sample Rate = 491.52 MSPS

Figure 66. Observation Receiver HD3, Left Side vs. Baseband Offset

Frequency, −5 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

–40

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

–50

–60

–50

–60

–70

–80

–90

–100

–110

–120

–100

–110

–120

–100 –80 –60 –40 –20

0

20

40

60

80

100

–60

–40

–20

0

20

40

60

BASEBAND OFFSET FREQUENCY (MHz)

Figure 67. Observation Receiver HD3, Right Side vs. Baseband Offset

Frequency, −5 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

Figure 64. Observation Receiver HD2, Left Side vs. Baseband Offset

Frequency, −5 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

90

80

70

60

–40

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

–50

–60

–70

–80

–90

–100

–110

–120

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

50

40

805 815 825 835 845 855 865 875 885 895 905

–100 –80 –60 –40 –20

0

20

40

60

80

100

TONE 2 FREQUENCY (MHz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 68. Observation Receiver IIP2, f1 + f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 65. Observation Receiver HD2, Right Side vs. Baseband Offset

Frequency, −5 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

Rev. E | Page 36 of 115

Data Sheet

ADRV9010

90

80

70

60

100

90

80

70

60

50

40

+110°C, ORx1

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

50

40

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

805

835

865

895

925

955

985

1015

0

5

10

15

20

25

30

TONE 2 FREQUENCY (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 69. Observation Receiver IIP2, f1 − f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 72. Observation Receiver IIP2, f1 + f2 vs. Observation Receiver

Attenuation, Both Tones at −11 dBFS, f1 = 102 MHz, f2 = 2 MHz

90

80

70

60

100

90

80

70

60

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

50

40

50

40

10

40

70

100

130

160

190

220

0

5

10

15

20

25

30

TWO-TONE FREQUENCY SPACING (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 70. Observation Receiver IIP2, f1 + f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Figure 73. Observation Receiver IIP2, f1 − f2 vs. Observation Receiver

Attenuation, Both Tones at −11 dBFS, f1 = 102 MHz, f2 = 2 MHz

90

80

70

60

40

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

35

30

25

20

15

10

5

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

50

40

0

10

40

70

100

130

160

190

220

805

815

825

835

845

855

865

TWO-TONE FREQUENCY SPACING (MHz)

TONE 2 FREQUENCY (MHz)

Figure 71. Observation Receiver IIP2, f1 − f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Figure 74. Observation Receiver IIP3, 2f1 + f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Rev. E | Page 37 of 115

ADRV9010

Data Sheet

40

35

30

25

20

15

10

5

30

25

20

15

10

5

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

0

805

0

10

815

825

835

845

855

865

20

30

40

50

60

70

80

90

100

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 75. Observation Receiver IIP3, 2f2 + f1 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 78. Observation Receiver IIP3, 2f1 + f2 vs. Two-Tone Frequency

Spacing, Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

40

30

25

20

15

10

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

35

30

25

20

15

10

5

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

5

0

805

835

865

895

925

955

985

1015

10

30

50

70

90

110 130 150 170 190 210

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 76. Observation Receiver IIP3, 2f1 − f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 79. Observation Receiver IIP3, 2f2 + f1 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

40

30

25

20

15

10

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

35

30

25

20

15

10

5

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

5

0

805

835

865

895

925

955

985

1015

10

30

50

70

90

110

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 77. Observation Receiver IIP3, 2f2 − f1 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 80. Observation Receiver IIP3, 2f1 − f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Rev. E | Page 38 of 115

Data Sheet

ADRV9010

30

25

20

15

10

5

40

35

30

25

20

15

10

5

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

0

10

0

40

70

100

130

160

190

220

0

5

10

15

20

TWO-TONE FREQUENCY SPACING (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 81. Observation Receiver IIP3, 2f2 − f1 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Figure 83. Observation Receiver IIP3, 2f2 − f1 vs. Observation Receiver

Attenuation, Both Tones at −11 dBFS, f1 = 122 MHz, f2 = 2 MHz

40

35

30

25

20

15

10

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

5

0

5

10

15

20

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 82. Observation Receiver IIP3, 2f2 + f1 vs. Observation Receiver

Attenuation, Both Tones at −11 dBFS, f1 = 122 MHz, f2 = 2 MHz

Rev. E | Page 39 of 115

ADRV9010

Data Sheet

1800 MHz BAND

The temperature settings refer to the die temperature. All LO frequencies set to 1800 MHz, unless otherwise noted.

7.0

6.5

6.0

5.5

5.0

4.5

4.0

3.5

3.0

–100

–110

–120

–130

–140

–150

–160

–170

–180

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+110°C

+25°C

–40°C

1500

1600

1700

1800

1900

2000

0

5

10

15

20

TRANSMITTER LO FREQUENCY (MHz)

TRANSMITTER ATTENUATION (dB)

Figure 84. Transmitter CW Output Power vs. Transmitter LO Frequency,

10 MHz Offset, 0 dB Attenuation

Figure 87. Transmitter Noise vs. Transmitter Attenuation,

50 MHz Offset Frequency

1.0

0

+110°C

+25°C

–40°C

SIGNAL

NOISE FLOOR

0.9

0.8

0.7

0.6

0.5

0.4

0.3

0.2

0.1

0

–10

–20

–30

–40

–50

–60

–70

–80

–90

–100

–0.1

–250 –200 –150 –100 –50

0

50

100 150 200 250

BASEBAND OFFSET FREQUENCY (MHz)

FREQUENCY (MHz)

Figure 88. Transmitter Pass Band Flatness vs. Baseband Offset Frequency

Figure 85. Transmitter Output Power Spectrum, Tx1, 5 MHz LTE,

10 MHz Offset, −10 dBFS RMS, 1 MHz Resolution Bandwidth, T = 25°C

–40

+110°C

+25°C

–40°C

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

–45

–50

–55

–60

–65

–70

–75

–80

–50

–60

–70

–80

–90

–100

0

5

10

15

20

–100 –80 –60 –40 –20

0

20

40

60

80

100

TRANSMITTER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 89. Adjacent Channel Power Level vs. Transmitter Attenuation,

−10 MHz Baseband Offset, 20 MHz LTE, PAR = 12 dB,

Figure 86. Transmitter Image Rejection vs. Baseband Offset Frequency,

0 dB Attenuation, QEC Tracking Enabled

Loop Filter Bandwidth = 50 kHz, Loop Filter Phase Margin = 40°

Rev. E | Page 40 of 115

Data Sheet

ADRV9010

–40

–45

–50

–55

–60

–65

–70

–75

0.05

0.04

0.03

0.02

0.01

0

+110°C

+25°C

–40°C

+110°C

+25°C

–40°C

–0.01

–0.02

–0.03

–0.04

–0.05

–80

0

5

10

15

20

0

4

8

12

16

20

24

28

32

TRANSMITTER ATTENUATION (dB)

Figure 90. Adjacent Channel Power Level vs. Transmitter Attenuation,

90 MHz Baseband Offset, 20 MHz LTE, PAR = 12 dB,

Figure 93. Transmitter Attenuator Step Error vs. Transmitter Attenuation,

10 MHz Offset

Loop Filter Bandwidth = 50 kHz, Loop Filter Phase Margin = 40°

–60

–40

+110°C, UPPER HD2

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

–65

–70

+25°C, UPPER HD2

–40°C, UPPER HD2

+110°C, LOWER HD2

+25°C, LOWER HD2

–40°C, LOWER HD2

–42

–44

–46

–48

–50

–75

–80

–85

–90

–95

–100

–105

0

2

4

6

8

10

12

14

16

18

20

0

5

10

15

20

TRANSMITTER ATTENUATION (dB)

Figure 91. Transmitter HD2 vs. Transmitter Attenuation, 10 MHz Offset

Figure 94. Transmitter Error Vector Magnitude vs. Transmitter Attenuation,

20 MHz LTE Signal Centered at LO Frequency, Sample Rate = 491.52 MSPS, QEC

Tracking Enabled, Loop Filter Bandwidth = 50 kHz, Loop Filter Phase Margin = 40°

–60

45

40

35

30

25

20

15

10

5

+110°C, UPPER HD3

+25°C, UPPER HD3

–40°C, UPPER HD3

–70

+110°C, LOWER HD3

+25°C, LOWER HD3

–40°C, LOWER HD3

–80

–90

–100

–110

–120

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

0

–5

–10

0

2

4

6

8

10

12

14

16

18

20

0

4

8

12

16

20

24

28

32

TRANSMITTER ATTENUATION (dB)

Figure 92. Transmitter HD3 vs. Transmitter Attenuation, 10 MHz Offset

Figure 95. Transmitter OIP3, 2f1 − f2 vs. Transmitter Attenuation,

15 dB Digital Backoff per Tone, f1 = 50.5 MHz, f2 = 55.5 MHz

Rev. E | Page 41 of 115

ADRV9010

Data Sheet

45

40

35

30

25

20

15

10

5

50

45

40

35

30

25

20

15

10

5

+110°C, Tx1

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

0

–5

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–10

0

10

0

4

8

12

16

20

24

28

32

30

50

70

90

110

130

150

170

190

TRANSMITTER ATTENUATION (dB)

f1 BASEBAND OFFSET TONE FREQUENCY (MHz)

Figure 96. Transmitter OIP3, 2f2 − f1 vs. Transmitter Attenuation,

15 dB Digital Backoff per Tone, f1 = 50.5 MHz, f2 = 55.5 MHz

Figure 99. Transmitter OIP3, 2f1 + f2 vs. f1 Baseband Offset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Backoff per Tone

50

45

40

35

30

25

20

15

50

45

40

35

30

25

20

15

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

10

5

10

5

0

10

0

10

30

50

70

90

110

130

150

170

190

30

50

70

90

110

130

150

170

190

f1 BASEBAND OFFSET TONE FREQUENCY (MHz)

Figure 97. Transmitter OIP3, 2f1 − f2 vs. f1 Baseband Offset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Backoff per Tone

Figure 100. Transmitter OIP3, 2f2 + f1 vs. f1 Baseband Offset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Backoff per Tone

50

45

40

35

30

25

20

15

120

110

100

90

80

70

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

10

5

Tx1 TO Tx2

Tx2 TO Tx1

Tx3 TO Tx1

Tx4 TO Tx1

Tx1 TO Tx3

Tx2 TO Tx3

Tx3 TO Tx2

Tx4 TO Tx2

Tx1 TO Tx4

Tx2 TO Tx4

Tx3 TO Tx4

Tx4 TO Tx3

60

50

0

10

30

50

70

90

110

130

150

170

190

1500

1550

1600

1650

1700

1750

1800

f1 BASEBAND OFFSET TONE FREQUENCY (MHz)

TRANSMITTER LO FREQUENCY (MHz)

Figure 101. Transmitter to Transmitter Isolation vs. Transmitter

LO Frequency

Figure 98. Transmitter OIP3, 2f2 − f1 vs. f1 Baseband Offset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Backoff per Tone

Rev. E | Page 42 of 115

Data Sheet

ADRV9010

130

120

110

100

90

50

45

40

35

30

25

20

15

10

5

Tx1 TO Rx1

Tx2 TO Rx1

Tx3 TO Rx1

Tx4 TO Rx1

Tx1 TO Rx2

Tx2 TO Rx2

Tx3 TO Rx2

Tx4 TO Rx2

80

70

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

Tx1 TO Rx3

Tx2 TO Rx3

Tx3 TO Rx3

Tx4 TO Rx3

Tx1 TO Rx4

Tx2 TO Rx4

Tx3 TO Rx4

Tx4 TO Rx4

60

50

1500

0

1550

1600

1650

1700

1750

1800

0

5

10

15

20

25

30

RECEIVER LO FREQUENCY (MHz)

RECEIVER ATTENUATION (dB)

Figure 102. Transmitter to Receiver Isolation vs. Receiver LO Frequency

Figure 105. Receiver Integrated Noise Figure vs. Receiver Attenuation,

20 MHz Offset, 200 MHz Bandwidth, Sample Rate = 245.76 MSPS,

Integration Bandwidth = 500 kHz to 100 MHz

25

140

130

120

110

100

90

+110°C

+25°C

–40°C

20

15

10

5

Tx1 TO ORx1

Tx2 TO ORx1

Tx3 TO ORx1

Tx4 TO ORx1

Tx1 TO ORx2

Tx2 TO ORx2

Tx3 TO ORx2

Tx4 TO ORx2

80

70

60

50

Tx1 TO ORx3

Tx1 TO ORx4

Tx2 TO ORx4

Tx3 TO ORx4

Tx4 TO ORx4

Tx2 TO ORx3

Tx3 TO ORx3

Tx4 TO ORx3

0

–100 –80 –60 –40 –20

0

20

40

60

80

100

1500

1550

1600

1650

1700

1750

1800

BASEBAND OFFSET FREQUENCY (MHz)

TRANSMITTER LO FREQUENCY (MHz)

Figure 103. Transmitter to Observation Receiver Isolation vs. Transmitter

LO Frequency

Figure 106. Receiver Integrated Noise Figure vs. Baseband Offset Frequency,

200 MHz Bandwidth, Sample Rate = 245.76 MSPS, Integrated in 200 kHz Steps

120

110

100

90

–40

+110°C

+25°C

–40°C

–50

–60

–70

80

–80

70

Rx1 TO Rx2

Rx2 TO Rx1

Rx3 TO Rx1

Rx4 TO Rx1

Rx1 TO Rx3

Rx2 TO Rx3

Rx3 TO Rx2

Rx4 TO Rx2

Rx1 TO Rx4

Rx2 TO Rx4

Rx3 TO Rx4

Rx4 TO Rx3

–90

60

50

–100

1500

1550

1600

1650

1700

1750

1800

1500

1600

1700

1800

1900

2000

RECEIVER LO FREQUENCY (MHz)

Figure 104. Receiver to Receiver Isolation vs. Receiver LO Frequency

Figure 107. Receiver LO Leakage vs. Receiver LO Frequency,

Attenuation = 0 dB, Sample Rate = 245.76 MSPS

Rev. E | Page 43 of 115

ADRV9010

Data Sheet

0.5

0.4

20

15

10

5

+110°C

+25°C

–40°C

0.3

0.2

0.1

0

–0.1

–0.2

–0.3

–0.4

–0.5

–5

+110°C, Rx1

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–10

–15

–100 –80 –60 –40 –20

0

20

40

60

80

100

0

5

10

15

20

25

30

BASEBAND OFFSET FREQUENCY (MHz)

RECEIVER ATTENUATION (dB)

Figure 111. Normalized Receiver Flatness vs. Baseband Offset Frequency,

−5 dBFS Input Signal

Figure 108. Receiver Gain vs. Receiver Attenuation, 20 MHz Offset,

200 MHz Bandwidth, Sample Rate = 245.76 MSPS

–40

20

19

18

17

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

–50

–60

–70

–80

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

16

15

–90

–100

–100 –80 –60 –40 –20

0

20

40

60

80

100

1500

1600

1700

1800

1900

2000

BASEBAND OFFSET FREQUENCY (MHz)

RECEIVER LO FREQUENCY (MHz)

Figure 109. Receiver Gain vs. Receiver LO Frequency, 10 MHz Offset,

200 MHz Bandwidth, Sample Rate = 245.76 MSPS

Figure 112. Receiver Image vs. Baseband Offset Frequency, Tracking Calibration

Active, Sample Rate = 245.76 MSPS, −5 dBFS Input Signal

–40

0.20

0.15

0.10

0.05

0

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

–50

–60

–70

–0.05

–0.10

–80

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

–90

–0.15

–0.20

–100

0

5

10

15

20

25

30

0

5

10

15

20

25

30

RECEIVER ATTENUATION (dB)

Figure 113. Receiver Image vs. Receiver Attenuation, 20 MHz Offset,

Tracking Calibration Active, Sample Rate = 245.76 MSPS, −5 dBFS Input Signal

Figure 110. Receiver Gain Step Error vs. Receiver Attenuation, 20 MHz Offset,

−5 dBFS Input Signal

Rev. E | Page 44 of 115

Data Sheet

ADRV9010

–40

–50

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

–50

–60

–70

–80

–90

–100

–110

–120

–100

–110

0

5

10

15

20

25

30

–40

–30

–20

–10

0

10

20

30

40

RECEIVER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 114. Receiver DC Offset vs. Receiver Attenuation, 20 MHz Offset,

−5 dBFS Input Signal

Figure 117. Receiver HD3, Left Side vs. Baseband Offset Frequency,

−5 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

–40

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

–50

–60

–50

–60

–70

–80

–90

–100

–110

–120

–100

–110

–120

–60

–40

–20

0

20

40

60

–40

–30

–20

–10

0

10

20

30

40

BASEBAND OFFSET FREQUENCY (MHz)

Figure 115. Receiver HD2, Left Side vs. Baseband Offset Frequency,

−5 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

(HD2 Canceller Not Enabled)

Figure 118. Receiver HD3, Right Side vs. Baseband Offset Frequency,

−5 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

–40

90

85

80

75

70

65

60

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

–50

–60

–70

–80

–90

–100

–110

–120

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

55

50

–60

–40

–20

0

20

40

60

1805

1815

1825

1835

1845

BASEBAND OFFSET FREQUENCY (MHz)

TONE 2 FREQUENCY (MHz)

Figure 116. Receiver HD2, Right Side vs. Baseband Offset Frequency,

−5 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

(HD2 Canceller Not Enabled)

Figure 119. Receiver IIP2, f1 + f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Rev. E | Page 45 of 115

ADRV9010

Data Sheet

90

85

80

75

70

65

60

55

50

100

95

90

85

80

75

70

65

60

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

1805 1815 1825 1835 1845 1855 1865 1875 1885 1895

0

5

10

15

20

25

30

TONE 2 FREQUENCY (MHz)

RECEIVER ATTENUATION (dB)

Figure 120. Receiver IIP2, f1 − f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 123. Receiver IIP2, f1 + f2 vs. Receiver Attenuation,

Both Tones at −11 dBFS, f1 = 92 MHz, f2 = 2 MHz

90

85

80

75

70

65

60

100

95

90

85

80

75

70

65

60

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

55

50

10

20

30

40

50

60

70

80

90

0

5

10

15

20

25

30

TWO-TONE FREQUENCY SPACING (MHz)

RECEIVER ATTENUATION (dB)

Figure 121. Receiver IIP2, f1 + f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Figure 124. Receiver IIP2, f1 − f2 vs. Receiver Attenuation,

Both Tones at −11 dBFS, f1 = 92 MHz, f2 = 2 MHz

80

75

70

65

60

40

35

30

25

20

15

10

5

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

55

50

10

0

1805

20

30

40

50

60

70

80

90

1810

1815

1820

1825

TWO-TONE FREQUENCY SPACING (MHz)

TONE 2 FREQUENCY (MHz)

Figure 122. Receiver IIP2, f1 − f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Figure 125. Receiver IIP3, 2f1 + f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Rev. E | Page 46 of 115

Data Sheet

ADRV9010

40

35

30

25

20

15

10

5

35

30

25

20

15

10

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

0

1805

1810

1815

1820

1825

10

15

20

25

30

35

40

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 126. Receiver IIP3, 2f2 + f1 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 129. Receiver IIP3, 2f1 + f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

40

35

30

25

20

35

30

25

20

15

10

5

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

15

0

10

1805 1815 1825 1835 1845 1855 1865 1875 1885 1895

20

30

40

50

60

70

80

90

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 127. Receiver IIP3, 2f1 − f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 130. Receiver IIP3, 2f2 + f1 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

40

35

30

25

20

35

30

25

20

15

10

5

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

15

0

10

1805 1815 1825 1835 1845 1855 1865 1875 1885 1895

15

20

25

30

35

40

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 128. Receiver IIP3, 2f2 − f1 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 131. Receiver IIP3, 2f1 − f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Rev. E | Page 47 of 115

ADRV9010

Data Sheet

–80

–90

35

30

25

20

–100

–110

–120

–130

–140

–150

–160

–170

+110°C, Rx1

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

15

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

10

100

1k

10k

100k

1M

10M

20

30

40

50

60

70

80

90

FREQUENCY OFFSET (Hz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 135. LO Phase Noise vs. Frequency Offset, Loop Bandwidth = 100 kHz,

Phase Margin = 60°

Figure 132. Receiver IIP3, 2f2 − f1 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

50

–20

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

45

40

35

30

25

20

15

10

5

–25

–30

–35

–40

–45

–50

0

5

10

15

20

–60 –55 –50 –45 –40 –35 –30 –25 –20 –15 –10 –5

0

5

OBSERVATION RECEIVER ATTENUATION (dB)

RECEIVER INPUT POWER (dBm)

Figure 136. Observation Receiver Integrated Noise Figure vs. Observation Receiver

Attenuation, 20 MHz Offset, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS,

Integration Bandwidth = 500 kHz to 100 MHz

Figure 133. Receiver Error Vector Magnitude vs. Receiver Input Power,

20 MHz LTE Signal Centered at LO Frequency, Sample Rate = 245.76 MSPS,

Loop Filter Bandwidth = 50 kHz, Loop Filter Phase Margin = 40°

35

30

25

20

15

–80

–90

–100

–110

–120

–130

–140

–150

–160

–170

10

5

+110°C

+25°C

–40°C

0

–250

100

1k

10k

100k

1M

10M

–150

–50

50

150

250

FREQUENCY OFFSET (Hz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 134. LO Phase Noise vs. Frequency Offset, Loop Bandwidth = 50 kHz,

Phase Margin = 85°

Figure 137. Observation Receiver Integrated Noise Figure vs. Baseband Offset

Frequency, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS,

Integrated in 200 kHz Steps

Rev. E | Page 48 of 115

Data Sheet

ADRV9010

–40

–50

–60

–70

–80

–90

–100

0.20

0.15

0.10

0.05

0

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

–0.05

–0.10

–0.15

–0.20

+110°C

+25°C

–40°C

1500

1600

1700

1800

1900

2000

0

5

10

15

20

25

30

OBSERVATION RECEIVER LO FREQUENCY (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 138. Observation Receiver LO Leakage vs. Observation Receiver

LO Frequency, 0 dB Attenuation, Sample Rate = 491.52 MSPS

Figure 141. Observation Receiver Gain Step Error vs. Observation Receiver

Attenuation, 20 MHz Offset, −5 dBFS Input Signal

20

15

10

5

0.6

0.4

0.2

0

–0.2

–5

+110°C

+25°C

–40°C

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

–0.4

–10

–15

–0.6

0

5

10

15

20

25

30

–220 –180 –140 –100 –60 –20 20

60 100 140 180 220

OBSERVATION RECEIVER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 139. Observation Receiver Gain vs. Observation Receiver Attenuation,

20 MHz Offset, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS

Figure 142. Normalized Observation Receiver Flatness vs. Baseband Offset

Frequency, −25 dBm Input Signal, 0 dB Attenuation

20

19

18

17

–40

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

–50

–60

–70

–80

16

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

–90

15

1500

–100

1600

1700

1800

1900

2000

–225 –175 –125 –75

–25

25

75

125

175

225

OBSERVATION RECEIVER LO FREQUENCY (MHz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 140. Observation Receiver Gain vs. Observation Receiver LO

Frequency, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS

Figure 143. Observation Receiver Image vs. Baseband Offset Frequency,

Tracking Calibration Active, Sample Rate = 491.52 MSPS

Rev. E | Page 49 of 115

ADRV9010

Data Sheet

–40

–50

–60

–70

–80

–90

–40

–50

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

–60

–70

–80

–90

–100

–110

–120

–100

0

5

10

15

20

25

30

–60

–40

–20

0

20

40

60

OBSERVATION RECEIVER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 144. Observation Receiver Image vs. Observation Receiver Attenuation,

20 MHz Offset, Tracking Calibration Active, Sample Rate = 491.52 MSPS

Figure 147. Observation Receiver HD3, Left Side vs. Baseband Offset

Frequency, −5 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

–40

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

–50

–60

–50

–60

–70

–80

–90

–100

–110

–120

–100

–110

–120

–100 –80 –60 –40 –20

0

20

40

60

80

100

–60

–40

–20

0

20

40

60

BASEBAND OFFSET FREQUENCY (MHz)

Figure 145. Observation Receiver HD2, Left Side vs. Baseband Offset

Frequency, −5 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

Figure 148. Observation Receiver HD3, Right Side vs. Baseband Offset

Frequency, −5 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

–40

90

85

80

75

70

65

60

55

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

–50

–60

–70

–80

–90

–100

–110

–120

50

45

40

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

–100 –80 –60 –40 –20

0

20

40

60

80

100

1805 1815 1825 1835 1845 1855 1865 1875 1885 1895 1905

BASEBAND OFFSET FREQUENCY (MHz)

TONE 2 FREQUENCY (MHz)

Figure 146. Observation Receiver HD2, Right Side vs. Baseband Offset

Frequency, −5 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

Figure 149. Observation Receiver IIP2, f1 + f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Rev. E | Page 50 of 115

Data Sheet

ADRV9010

90

85

80

75

70

65

60

55

100

90

80

70

60

50

40

50

45

40

+110°C, ORx1

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

1805

1835

1865

1895

1925

1955

1985

2015

0

5

10

15

20

25

30

TONE 2 FREQUENCY (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 150. Observation Receiver IIP2, f1 − f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 153. Observation Receiver IIP2, f1 + f2 vs. Observation Receiver

Attenuation, Both Tones at −11 dBFS, f1 = 102 MHz, f2 = 2 MHz

90

80

70

60

100

90

80

70

60

50

40

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

50

40

10

40

70

100

130

160

190

220

0

5

10

15

20

25

30

TWO-TONE FREQUENCY SPACING (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 151. Observation Receiver IIP2, f1 + f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Figure 154. Observation Receiver IIP2, f1 − f2 vs. Observation Receiver

Attenuation, Both Tones at −11 dBFS, f1 = 102 MHz, f2 = 2 MHz

80

75

70

65

60

55

50

40

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

35

30

25

20

15

10

5

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

45

40

0

10

40

70

100

130

160

190

220

1805

1815

1825

1835

1845

1855

1865

TWO-TONE FREQUENCY SPACING (MHz)

TONE 2 FREQUENCY (MHz)

Figure 152. Observation Receiver IIP2, f1 − f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Figure 155. Observation Receiver IIP3, 2f1 + f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Rev. E | Page 51 of 115

ADRV9010

Data Sheet

40

35

30

25

20

15

10

5

30

25

20

15

10

5

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

0

1805

0

10

1815

1825

1835

1845

1855

1865

20

30

40

50

60

70

80

90

100

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 156. Observation Receiver IIP3, 2f2 + f1 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 159. Observation Receiver IIP3, 2f1 + f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

40

30

25

20

15

10

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

35

30

25

20

15

10

5

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

5

0

1805

0

10

1835

1865

1895

1925

1955

1965

2015

30

50

70

90

110 130 150 170 190 210

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 157. Observation Receiver IIP3, 2f1 − f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 160. Observation Receiver IIP3, 2f2 + f1 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

40

30

25

20

15

10

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

35

30

25

20

15

10

5

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

5

0

1805

0

10

1835

1865

1895

1925

1955

1965

2015

30

50

70

90

110

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 158. Observation Receiver IIP3, 2f2 − f1 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 161. Observation Receiver IIP3, 2f1 − f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Rev. E | Page 52 of 115

Data Sheet

ADRV9010

30

25

20

15

10

5

60

50

40

30

20

10

0

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

0

10

40

70

100

130

160

190

220

0

5

10

15

20

25

30

TWO-TONE FREQUENCY SPACING (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 162. Observation Receiver IIP3, 2f2 − f1 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Figure 164. Observation Receiver IIP3, 2f2 − f1 vs. Observation Receiver

Attenuation, Both Tones at −11 dBFS, f1 = 122 MHz, f2 = 2 MHz

60

50

40

30

20

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

10

0

5

10

15

20

25

30

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 163. Observation Receiver IIP3, 2f2 + f1 vs. Observation Receiver

Attenuation, Both Tones at −11 dBFS, f1 = 122 MHz, f2 = 2 MHz

Rev. E | Page 53 of 115

ADRV9010

Data Sheet

2600 MHz BAND

The temperature settings refer to the die temperature. All LO frequencies set to 2600 MHz, unless otherwise noted.

7.0

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

6.5

6.0

5.5

5.0

4.5

4.0

3.5

3.0

–40°C

+25°C

+110°C

0

5

10

15

20

1800 1900 2000 2100 2200 2300 2400 2500 2600 2700 2800

TRANSMITTER ATTENUATION (dB)

TRANSMITTER LO FREQUENCY (MHz)

Figure 168. Transmitter Noise vs. Transmitter Attenuation, 50 MHz Offset

Figure 165. Transmitter CW Output Power vs. Transmitter LO Frequency,

10 MHz Offset, 0 dB Attenuation

0.8

0

–40°C

+25°C

+110°C

SIGNAL

ANALYZER NOISE FLOOR

–10

0.6

0.4

0.2

0

–20

–30

–40

–50

–60

–70

–80

–90

–0.2

–0.4

–100

–250 –200 –150 –100 –50

0

50

100 150 200 250

2100 2200 2300 2400 2500 2600 2700 2800 2900 3000 3100

BASEBAND OFFSET FREQUENCY (MHz)

FREQUENCY (MHz)

Figure 169. Transmitter Pass Band Flatness vs. Baseband Offset Frequency

Figure 166. Transmitter Output Power Spectrum, Tx1, 5 MHz LTE,

10 MHz Offset, −10 dBFS RMS, 1 MHz Resolution Bandwidth, T = 25°C

–40

–40°C

+25°C

+110°C

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–45

–50

–55

–60

–65

–70

–75

–80

0

5

10

15

20

–100 –80 –60 –40 –20

0

20

40

60

80

100

TRANSMITTER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 170. Adjacent Channel Power Level vs. Transmitter Attenuation,

−10 MHz Baseband Offset, 20 MHz LTE, PAR = 12 dB, Loop Filter Bandwidth =

500 kHz, Loop Filter Phase Margin = 60°

Figure 167. Transmitter Image Rejection vs. Baseband Offset Frequency,

0 dB Attenuation, QEC Tracking Enabled

Rev. E | Page 54 of 115

Data Sheet

ADRV9010

–40

0.05

0.04

0.03

0.02

0.01

0

–40°C

+25°C

+110°C

–40°C

+25°C

+110°C

–45

–50

–55

–60

–65

–70

–75

–80

–0.01

–0.02

–0.03

–0.04

–0.05

0

5

10

15

20

0

4

8

12

16

20

24

28

32

TRANSMITTER ATTENUATION (dB)

Figure 171. Adjacent Channel Power Level vs. Transmitter Attenuation,

90 MHz Baseband Offset, 20 MHz LTE, PAR = 12 dB,

Figure 174. Transmitter Attenuator Step Error vs. Transmitter Attenuation,

10 MHz Offset

Loop Filter Bandwidth = 500 kHz, Loop Filter Phase Margin = 60°

–60

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–40°C, LOWER HD2

+25°C, LOWER HD2

+110°C, LOWER HD2

–40°C, UPPER HD2

+25°C, UPPER HD2

+110°C, UPPER HD2

–70

–80

–90

–100

–110

–120

0

2

4

6

8

10

12

14

16

18

20

0

2

4

6

8

10

12

14

16

18

20

TRANSMITTER ATTENUATION (dB)

Figure 175. Transmitter Error Vector Magnitude vs. Transmitter Attenuation,

20 MHz LTE Signal Centered at LO Frequency, Sample Rate = 491.52 MSPS,

QEC Tracking Enabled, Loop Filter Bandwidth = 500 kHz,

Loop Filter Phase Margin = 60°

Figure 172. Transmitter HD2 vs. Transmitter Attenuation, 10 MHz Offset

–60

–40°C, LOWER HD3

+25°, LOWER HD3

+110°C, LOWER HD3

–40°C, UPPER HD3

+25°C, UPPER HD3

+110°C, UPPER HD3

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–70

–80

–90

–100

–110

–120

0

2

4

6

8

10

12

14

16

18

20

0

4

8

12

16

20

24

28

32

TRANSMITTER ATTENUATION (dB)

Figure 173. Transmitter HD3 vs. Transmitter Attenuation, 10 MHz Offset

Figure 176. Transmitter OIP3, 2f1 − f2 vs. Transmitter Attenuation,

15 dB Digital Backoff per Tone, f1 = 50.5 MHz, f2 = 55.5 MHz

Rev. E | Page 55 of 115

ADRV9010

Data Sheet

–40°C, Tx1

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

10

30

50

70

90

110

130

150

170

190

0

4

8

12

16

20

24

28

32

f1 BASEBAND OFFSET TONE FREQUENCY (MHz)

TRANSMITTER ATTENUATION (dB)

Figure 177. Transmitter OIP3, 2f2 − f1 vs. Transmitter Attenuation,

15 dB Digital Backoff per Tone, f1 = 50.5 MHz, f2 = 55.5 MHz

Figure 180. Transmitter OIP3, 2f1 + f2 vs. f1 Baseband Offset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Backoff per Tone

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

10

30

50

70

90

110

130

150

170

190

10

30

50

70

90

110

130

150

170

190

f1 BASEBAND OFFSET TONE FREQUENCY (MHz)

Figure 178. Transmitter OIP3, 2f1 − f2 vs. f1 Baseband Oﬀset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Backoff per Tone

Figure 181. Transmitter OIP3, 2f2 + f1 vs. f1 Baseband Offset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Backoff per Tone

Tx1 TO Tx2

Tx2 TO Tx1

Tx3 TO Tx1

Tx4 TO Tx1

Tx1 TO Tx3

Tx2 TO Tx3

Tx3 TO Tx2

Tx4 TO Tx2

Tx1 TO Tx4

Tx2 TO Tx4

Tx3 TO Tx4

Tx4 TO Tx3

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

10

30

50

70

90

110

130

150

170

190

1800 1900 2000 2100 2200 2300 2400 2500 2600 2700 2800

TRANSMITTER LO FREQUENCY (MHz)

f1 BASEBAND OFFSET TONE FREQUENCY (MHz)

Figure 179. Transmitter OIP3, 2f2 − f1 vs. f1 Baseband Oﬀset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Backoff per Tone

Figure 182. Transmitter to Transmitter Isolation vs.

Transmitter LO Frequency

Rev. E | Page 56 of 115

Data Sheet

ADRV9010

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

Tx1 TO Rx1

Tx1 TO Rx2

Tx2 TO Rx2

Tx3 TO Rx2

Tx4 TO Rx2

Tx1 TO Rx3

Tx2 TO Rx3

Tx3 TO Rx3

Tx4 TO Rx3

Tx1 TO Rx4

Tx2 TO Rx4

Tx3 TO Rx4

Tx4 TO Rx4

Tx2 TO Rx1

Tx3 TO Rx1

Tx4 TO Rx1

0

5

10

15

20

1800 1900 2000 2100 2200 2300 2400 2500 2600 2700 2800

RECEIVER LO FREQUENCY (MHz)

RECEIVER ATTENUATION (dB)

Figure 183. Transmitter to Receiver Isolation vs. Receiver LO Frequency

Figure 186. Receiver Integrated Noise Figure vs. Receiver Attenuation,

20 MHz Offset, 200 MHz Bandwidth, Sample Rate = 245.76 MSPS, Integration

Bandwidth = 500 kHz to 100 MHz

25

–40°C

+25°C

+110°C

20

15

10

5

Tx1 TO ORx2

Tx2 TO ORx2

Tx3 TO ORx2

Tx4 TO ORx2

Tx1 TO ORx3

Tx2 TO ORx3

Tx3 TO ORx3

Tx4 TO ORx3

Tx1 TO ORx4

Tx2 TO ORx4

Tx3 TO ORx4

Tx4 TO ORx4

Tx1 TO ORx1

Tx2 TO ORx1

Tx3 TO ORx1

Tx4 TO ORx1

0

–100 –80 –60 –40 –20

0

20

40

60

80

100

1800 1900 2000 2100 2200 2300 2400 2500 2600 2700 2800

TRANSMITTER LO FREQUENCY (MHz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 184. Transmitter to Observation Receiver Isolation vs. Transmitter

LO Frequency

Figure 187. Receiver Integrated Noise Figure vs. Baseband Offset Frequency,

200 MHz Bandwidth, Sample Rate = 245.76 MSPS, Integrated in 200 kHz Steps

–50

–40°C

+25°C

+110°C

–55

–60

–65

–70

–75

Rx1 TO Rx2

Rx2 TO Rx1

Rx3 TO Rx1

Rx4 TO Rx1

Rx1 TO Rx3

Rx2 TO Rx3

Rx3 TO Rx2

Rx4 TO Rx2

Rx1 TO Rx4

Rx2 TO Rx4

Rx3 TO Rx4

Rx4 TO Rx3

–80

1800

2000

2200

2400

2600

2800

1800 1900 2000 2100 2200 2300 2400 2500 2600 2700 2800

RECEIVER LO FREQUENCY (MHz)

Figure 185. Receiver to Receiver Isolation vs. Receiver LO Frequency

Figure 188. Receiver LO Leakage vs. Receiver LO Frequency,

Attenuation = 0 dB, Sample Rate = 245.76 MSPS

Rev. E | Page 57 of 115

ADRV9010

Data Sheet

0.5

0.4

–40°C

+25°C

+110°C

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

0.3

0.2

0.1

0

–0.1

–0.2

–0.3

–0.4

–0.5

0

5

10

15

20

25

30

–100 –80 –60 –40 –20

0

20

40

60

80

100

RECEIVER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 192. Normalized Receiver Flatness vs. Baseband Offset Frequency,

−5 dBFS Input Signal

Figure 189. Receiver Gain vs. Receiver Attenuation, 20 MHz Offset,

200 MHz Bandwidth, Sample Rate = 245.76 MSPS

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–100 –80 –60 –40 –20

0

20

40

60

80

100

1800 1900 2000 2100 2200 2300 2400 2500 2600 2700 2800

RECEIVER LO FREQUENCY (MHz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 193. Receiver Image vs. Baseband Offset Frequency, Tracking Calibration

Active, Sample Rate = 245.76 MSPS, −5 dBFS Input Signal

Figure 190. Receiver Gain vs. Receiver LO Frequency, 10 MHz Offset,

200 MHz Bandwidth, Sample Rate = 245.76 MSPS

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

0

5

10

15

20

25

30

0

5

10

15

20

25

30

RECEIVER ATTENUATION (dB)

Figure 194. Receiver Image vs. Receiver Attenuation, 20 MHz Offset, Tracking

Calibration Active, Sample Rate = 245.76 MSPS, −5 dBFS Input Signal

Figure 191. Receiver Gain Step Error vs. Receiver Attenuation,

20 MHz Offset, −5 dBFS Input Signal

Rev. E | Page 58 of 115

Data Sheet

ADRV9010

–40°C, Rx1

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

0

5

10

15

20

25

30

–40

–30

–20

–10

0

10

20

30

40

RECEIVER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 195. Receiver DC Offset vs. Receiver Attenuation, 20 MHz Offset,

−5 dBFS Input Signal

Figure 198. Receiver HD3, Left Side vs. Baseband Offset Frequency,

−5 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

0

20

40

60

–40

–30

–20

–10

0

10

20

30

40

BASEBAND OFFSET FREQUENCY (MHz)

Figure 196. Receiver HD2, Left Side vs. Baseband Offset Frequency,

−5 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

(HD2 Canceller Not Enabled)

Figure 199. Receiver HD3, Right Side vs. Baseband Offset Frequency,

−5 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–60

–40

–20

0

20

40

60

2605

2615

2625

2635

2645

BASEBAND OFFSET FREQUENCY (MHz)

TONE 2 FREQUENCY (MHz)

Figure 197. Receiver HD2, Right Side vs. Baseband Offset Frequency,

−5 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

(HD2 Canceller Not Enabled)

Figure 200. Receiver IIP2, f1 + f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Rev. E | Page 59 of 115

ADRV9010

Data Sheet

–40°C, Rx1

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

0

5

10

15

20

25

30

2605 2615 2625 2635 2645 2655 2665 2675 2685 2695

TONE 2 FREQUENCY (MHz)

RECEIVER ATTENUATION (dB)

Figure 201. Receiver IIP2, f1 − f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 204. Receiver IIP2, f1 + f2 vs. Receiver Attenuation,

Both Tones at −11 dBFS, f1 = 92 MHz, f2 = 2 MHz

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

0

5

10

15

20

25

30

10

20

30

40

50

60

70

80

90

RECEIVER ATTENUATION (dB)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 202. Receiver IIP2, f1 + f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Figure 205. Receiver IIP2, f1 − f2 vs. Receiver Attenuation,

Both Tones at −11 dBFS, f1 = 92 MHz, f2 = 2 MHz

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

10

20

30

40

50

60

70

80

90

2605

2610

2615

2620

2625

TWO-TONE FREQUENCY SPACING (MHz)

TONE 2 FREQUENCY (MHz)

Figure 203. Receiver IIP2, f1 − f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Figure 206. Receiver IIP3, 2f1 + f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Rev. E | Page 60 of 115

Data Sheet

ADRV9010

–40°C, Rx1

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, z4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

2605

2610

2615

2620

2625

10

15

20

25

30

35

40

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 207. Receiver IIP3, 2f2 + f1 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 210. Receiver IIP3, 2f1 + f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

10

20

30

40

50

60

70

80

90

2605 2615 2625 2635 2645 2655 2665 2675 2685 2695

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 208. Receiver IIP3, 2f1 − f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 211. Receiver IIP3, 2f2 + f1 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

10

15

20

25

30

35

40

2605 2615 2625 2635 2645 2655 2665 2675 2685 2695

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 209. Receiver IIP3, 2f2 − f1 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 212. Receiver IIP3, 2f1 − f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Rev. E | Page 61 of 115

ADRV9010

Data Sheet

–80

–90

–100

–110

–120

–130

–140

–150

–40°C, Rx1

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

10

20

30

40

50

60

70

80

90

100

1k

10k

100k

1M

10M

TWO-TONE FREQUENCY SPACING (MHz)

FREQUENCY OFFSET (Hz)

Figure 213. Receiver IIP3, 2f2 − f1 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Figure 216. LO Phase Noise vs. Frequency Offset, Loop Bandwidth = 500 kHz,

Phase Margin = 60°

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–60 –55 –50 –45 –40 –35 –30 –25 –20 –15 –10 –5

RECEIVER INPUT POWER (dBm)

0

5

0

5

10

15

20

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 214. Receiver Error Vector Magnitude vs. Receiver Input Power,

20 MHz LTE Signal Centered at LO Frequency, Sample Rate = 245.76 MSPS,

Loop Filter Bandwidth = 500 kHz, Loop Filter Phase Margin = 60°

Figure 217. Observation Receiver Integrated Noise Figure vs. Observation

Receiver Attenuation, 20 MHz Offset, 450 MHz Bandwidth,

Sample Rate = 491.52 MSPS, Integration Bandwidth = 500 kHz to 100 MHz

–80

–40°C

+25°C

+110°C

–90

–100

–110

–120

–130

–140

–150

–250

–150

–50

50

150

250

100

1k

10k

100k

1M

10M

BASEBAND OFFSET FREQUENCY (MHz)

FREQUENCY OFFSET (Hz)

Figure 215. LO Phase Noise vs. Frequency Offset, Loop Bandwidth = 75 kHz,

Phase Margin = 85°

Figure 218. Observation Receiver Integrated Noise Figure vs. Baseband Offset

Frequency, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS,

Integrated in 200 kHz Steps

Rev. E | Page 62 of 115

Data Sheet

ADRV9010

–50

–40°C

+25°C

+110°C

–55

–60

–65

–70

–75

–80

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

0

5

10

15

20

25

30

1800 1900 2000 2100 2200 2300 2400 2500 2600 2700 2800

OBSERVATION RECEIVER LO FREQUENCY (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 219. Observation Receiver LO Leakage vs. Observation Receiver

LO Frequency, 0 dB Attenuation, Sample Rate = 491.52 MSPS

Figure 222. Observation Receiver Gain Step Error vs. Observation Receiver

Attenuation, 20 MHz Offset, −5 dBFS Input Signal

–40°C

+25°C

+85°C

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

0

5

10

15

20

25

30

20

60 100 140 180 220

OBSERVATION RECEIVER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 220. Observation Receiver Gain vs. Observation Receiver Attenuation,

20 MHz Offset, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS

Figure 223. Normalized Observation Receiver Flatness vs. Baseband Offset

Frequency, −25 dBm Input Signal, 0 dB Attenuation

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

1800 1900 2000 2100 2200 2300 2400 2500 2600 2700 2800

OBSERVATION RECEIVER LO FREQUENCY (MHz)

–225 –175 –125 –75

–25

25

75

125

175

225

BASEBAND OFFSET FREQUENCY (MHz)

Figure 221. Observation Receiver Gain vs. Observation Receiver LO

Frequency, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS

Figure 224. Observation Receiver Image vs. Baseband Offset Frequency,

Tracking Calibration Active, Sample Rate = 491.52 MSPS

Rev. E | Page 63 of 115

ADRV9010

Data Sheet

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

–40°C, ORx1

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

0

5

10

15

20

25

30

–60

–40

–20

0

20

40

60

OBSERVATION RECEIVER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 225. Observation Receiver Image vs. Observation Receiver

Attenuation, 20 MHz Offset, Tracking Calibration Active,

Sample Rate = 491.52 MSPS

Figure 228. Observation Receiver HD3, Left Side vs. Baseband Offset

Frequency, −5 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–100 –80 –60 –40 –20

0

20

40

60

80

100

–60

–40

–20

0

20

40

60

BASEBAND OFFSET FREQUENCY (MHz)

Figure 226. Observation Receiver HD2, Left Side vs. Baseband Offset

Frequency, −5 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

Figure 229. Observation Receiver HD3, Right Side vs. Baseband Offset

Frequency, −5 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–100 –80 –60 –40 –20

0

20

40

60

80

100

2605 2615 2625 2635 2645 2655 2665 2675 2685 2695 2705

TONE 2 FREQUENCY(MHz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 227. Observation Receiver HD2, Right Side vs. Baseband Offset

Frequency, −5 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

Figure 230. Observation Receiver IIP2, f1 + f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Rev. E | Page 64 of 115

Data Sheet

ADRV9010

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

–40°C, ORx1

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

0

5

10

15

20

25

30

2605 2625 2645 2665 2685 2705 2725 2745 2765 2785 2805 2825

TONE 2 FREQUENCY (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 231. Observation Receiver IIP2, f1 − f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 234. Observation Receiver IIP2, f1 + f2 vs. Observation Receiver

Attenuation, Both Tones at −11 dBFS, f1 = 102 MHz, f2 = 2 MHz

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

10

40

70

100

130

160

190

220

0

5

10

15

20

25

30

OBSERVATION RECEIVER ATTENUATION (dB)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 235. Observation Receiver IIP2, f1 − f2 vs. Observation Receiver

Attenuation, Both Tones at −11 dBFS, f1 = 102 MHz, f2 = 2 MHz

Figure 232. Observation Receiver IIP2, f1 + f2 vs. Two-Tone Frequency

Spacing, Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

10

40

70

100

130

160

190

220

2605

2615

2625

2635

2645

2655

2665

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 236. Observation Receiver IIP3, 2f1 + f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 233. Observation Receiver IIP2, f1 − f2 vs. Two-Tone Frequency

Spacing, Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Rev. E | Page 65 of 115

ADRV9010

Data Sheet

–40°C, ORx1

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

2605

2615

2625

2635

2645

2655

2665

10

20

30

40

50

60

70

80

90

100

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 237. Observation Receiver IIP3, 2f2 + f1 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 240. Observation Receiver IIP3, 2f1 + f2 vs. Two-Tone Frequency

Spacing, Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

10

30

50

70

90

110 130 150 170 190 210

2605

2635

2665

2695

2725

2755

2785

2815

TWO-TONE FREQUENCY SPACING (MHz)

TONE 2 FREQUENCY (MHz)

Figure 238. Observation Receiver IIP3, 2f1 − f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 241. Observation Receiver IIP3, 2f2 + f1 vs. Two-Tone Frequency

Spacing, Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, Oz4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

10

30

50

70

90

110

2605

2635

2665

2695

2725

2755

2785

2815

TWO-TONE FREQUENCY SPACING (MHz)

TONE 2 FREQUENCY (MHz)

Figure 239. Observation Receiver IIP3, 2f2 − f1 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 242. Observation Receiver IIP3, 2f1 − f2 vs. Two-Tone Frequency

Spacing, Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Rev. E | Page 66 of 115

Data Sheet

ADRV9010

–40°C, ORx1

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

10

40

70

100

130

160

190

220

0

5

10

15

20

25

30

TWO-TONE FREQUENCY SPACING (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 243. Observation Receiver IIP3, 2f2 − f1 vs. Two-Tone Frequency

Spacing, Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Figure 245. Observation Receiver IIP3, 2f2 − f1 vs. Observation Receiver

Attenuation, Both Tones at −11 dBFS, f1 = 122 MHz, f2 = 2 MHz

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

0

5

10

15

20

25

30

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 244. Observation Receiver IIP3, 2f2 + f1 vs. Observation Receiver

Attenuation, Both Tones at −11 dBFS, f1 = 122 MHz, f2 = 2 MHz

Rev. E | Page 67 of 115

ADRV9010

Data Sheet

3800 MHz BAND

The temperature settings refer to the die temperature. All LO frequencies set to 3800 MHz, unless otherwise noted.

7.0

6.5

6.0

5.5

5.0

4.5

4.0

3.5

3.0

–100

–110

–120

–130

–140

–150

–160

–170

–180

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+110°C

+25°C

–40°C

3500

3600

3700

3800

3900

4000

0

5

10

15

20

TRANSMITTER LO FREQUENCY (MHz)

TRANSMITTER ATTENUATION (dB)

Figure 249. Transmitter Noise vs. Transmitter Attenuation,

50 MHz Offset Frequency

Figure 246. Transmitter CW Output Power vs. Transmitter LO Frequency,

10 MHz Offset, 0 dB Attenuation

1.0

0

+110°C

+25°C

–40°C

SIGNAL

–10

–20

–30

–40

–50

–60

–70

–80

–90

–100

NOISE FLOOR

0.8

0.6

0.4

0.2

0

–0.2

–250 –200 –150 –100 –50

0

50

100 150 200 250

3300 3400 3500 3600 3700 3800 3900 4000 4100 4200 4300

BASEBAND OFFSET FREQUENCY (MHz)

FREQUENCY (MHz)

Figure 247. Transmitter Output Power Spectrum, Tx1, 5 MHz LTE,

10 MHz Offset, −10 dBFS RMS, 1 MHz Resolution Bandwidth, T = 25°C

(Step at 3600 MHz Due to Spectrum Analyzer)

Figure 250. Transmitter Pass Band Flatness vs. Baseband Offset Frequency

–40

–20

+110°C

+25°C

–40°C

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

–45

–50

–55

–60

–65

–70

–75

–80

–30

–40

–50

–60

–70

–80

–90

–100

0

5

10

15

20

–100 –80 –60 –40 –20

0

20

40

60

80

100

TRANSMITTER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 251. Adjacent Channel Power Level vs. Transmitter Attenuation,

−10 MHz Baseband Offset, 20 MHz LTE, PAR = 12 dB, Loop Filter

Bandwidth = 600 kHz, Loop Filter Phase Margin = 75°

Figure 248. Transmitter Image Rejection vs. Baseband Offset Frequency,

0 dB Attenuation, QEC Tracking Enabled

Rev. E | Page 68 of 115

Data Sheet

ADRV9010

–40

0.05

0.04

0.03

0.02

0.01

0

+110°C

+25°C

–40°C

+110°C

+25°C

–40°C

–45

–50

–55

–60

–65

–70

–75

–80

–0.01

–0.02

–0.03

–0.04

–0.05

0

5

10

15

20

0

4

8

12

16

20

24

28

32

TRANSMITTER ATTENUATION (dB)

Figure 252. Adjacent Channel Power Level vs. Transmitter Attenuation,

90 MHz Baseband Offset, 20 MHz LTE, PAR = 12 dB, Loop Filter Bandwidth

= 600 kHz, Loop Filter Phase Margin = 75°

Figure 255. Transmitter Attenuator Step Error vs. Transmitter Attenuation,

10 MHz Offset

–38

–60

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+110°C, UPPER HD2

–39

–40

–41

–42

–43

–44

–45

–46

–47

–48

–65

+25°C, UPPER HD2

–40°C, UPPER HD2

–70

–75

+110°C, LOWER HD2

+25°C, LOWER HD2

–40°C, LOWER HD2

–80

–85

–90

–95

–100

–105

–110

0

2

4

6

8

10

12

14

16

18

20

0

2

4

6

8

10

12

14

16

18

20

TRANSMITTER ATTENUATION (dB)

Figure 256. Transmitter Error Vector Magnitude vs. Transmitter Attenuation,

20 MHz LTE Signal Centered at LO Frequency, Sample Rate = 491.52 MSPS,

QEC Tracking Enabled, Loop Filter Bandwidth = 600 kHz, Loop Filter

Phase Margin = 75°

Figure 253. Transmitter HD2 vs. Transmitter Attenuation, 10 MHz Offset

–60

45

40

35

30

25

20

15

10

5

+110°C, UPPER HD3

–65

+25°C, UPPER HD3

–40°C, UPPER HD3

–70

–75

+110°C, LOWER HD3

+25°C, LOWER HD3

–40°C, LOWER HD3

–80

–85

–90

–95

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

–100

–105

–110

0

–5

–10

0

2

4

6

8

10

12

14

16

18

20

0

4

8

12

16

20

24

28

32

TRANSMITTER ATTENUATION (dB)

Figure 254. Transmitter HD3 vs. Transmitter Attenuation, 10 MHz Offset

Figure 257. Transmitter OIP3, 2f1 − f2 vs. Transmitter Attenuation,

15 dB Digital Backoff per Tone, f1 = 50.5 MHz, f2 = 55.5 MHz

Rev. E | Page 69 of 115

ADRV9010

Data Sheet

45

40

35

30

25

20

15

10

5

50

45

40

35

30

25

20

15

10

5

+110°C, Tx1

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

0

–5

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–10

0

10

0

4

8

12

16

20

24

28

32

30

50

70

90

110

130

150

170

190

TRANSMITTER ATTENUATION (dB)

f1 BASEBAND OFFSET TONE FREQUENCY (MHz)

Figure 258. Transmitter OIP3, 2f2 − f1 vs. Transmitter Attenuation,

15 dB Digital Backoff per Tone, f1 = 50.5 MHz, f2 = 55.5 MHz

Figure 261. Transmitter OIP3, 2f1 + f2 vs. f1 Baseband Offset Tone

Frequency, f2 = f1 + 5 MHz, 15 dB Digital Backoff per Tone

50

45

40

35

30

25

20

15

50

45

40

35

30

25

20

15

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

10

5

10

5

0

10

0

10

30

50

70

90

110

130

150

170

190

30

50

70

90

110

130

150

170

190

f1 BASEBAND OFFSET TONE FREQUENCY (MHz)

Figure 259. Transmitter OIP3, 2f1 − f2 vs. f1 Baseband Offset Tone

Frequency, f2 = f1 + 5 MHz, 15 dB Digital Backoff per Tone

Figure 262. Transmitter OIP3, 2f2 + f1 vs. f1 Baseband Offset Tone

Frequency, f2 = f1 + 5 MHz, 15 dB Digital Backoff per Tone

50

45

40

35

30

25

20

15

120

110

100

90

80

70

60

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

10

5

Tx1 TO Tx2

Tx2 TO Tx1

Tx3 TO Tx1

Tx4 TO Tx1

Tx1 TO Tx3

Tx2 TO Tx3

Tx3 TO Tx2

Tx4 TO Tx2

Tx1 TO Tx4

Tx2 TO Tx4

Tx3 TO Tx4

Tx4 TO Tx3

50

40

0

10

30

50

70

90

110

130

150

170

190

3500

3600

3700

3800

3900

4000

f1 BASEBAND OFFSET TONE FREQUENCY (MHz)

TRANSMITTER LO FREQUENCY (MHz)

Figure 260. Transmitter OIP3, 2f2 − f1 vs. f1 Baseband Offset Tone

Frequency, f2 = f1 + 5 MHz, 15 dB Digital Backoff per Tone

Figure 263. Transmitter to Transmitter Isolation vs. Transmitter

LO Frequency

Rev. E | Page 70 of 115

Data Sheet

ADRV9010

130

120

110

100

90

50

45

40

35

30

25

20

15

10

5

80

70

60

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

Tx1 TO Rx1 Tx1 TO Rx2

Tx1 TO Rx3

Tx2 TO Rx3

Tx3 TO Rx3

Tx4 TO Rx3

Tx1 TO Rx4

Tx2 TO Rx4

Tx3 TO Rx4

Tx4 TO Rx4

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

Tx2 TO Rx1 Tx2 TO Rx2

Tx3 TO Rx1 Tx3 TO Rx2

Tx4 TO Rx1 Tx4 TO Rx2

50

40

0

3500

3600

3700

3800

3900

4000

0

5

10

15

20

25

30

RECEIVER LO FREQUENCY (MHz)

RECEIVER ATTENUATION (dB)

Figure 264. Transmitter to Receiver Isolation vs. Receiver LO Frequency

Figure 267. Receiver Integrated Noise Figure vs. Receiver Attenuation,

20 MHz Offset, 200 MHz Bandwidth, Sample Rate = 245.76 MSPS,

Integration Bandwidth = 500 kHz to 100 MHz

25

140

130

120

110

100

90

+110°C

+25°C

–40°C

20

15

10

5

80

Tx1 TO ORx1

Tx2 TO ORx1

Tx3 TO ORx1

Tx4 TO ORx1

Tx1 TO ORx2

Tx2 TO ORx2

Tx3 TO ORx2

Tx4 TO ORx2

70

60

50

40

Tx1 TO ORx3

Tx1 TO ORx4

Tx2 TO ORx4

Tx3 TO ORx4

Tx4 TO ORx4

Tx2 TO ORx3

Tx3 TO ORx3

Tx4 TO ORx3

0

–100 –80 –60 –40 –20

0

20

40

60

80

100

3500

3600

3700

3800

3900

4000

BASEBAND OFFSET FREQUENCY (MHz)

TRANSMITTER LO FREQUENCY (MHz)

Figure 265. Transmitter to Observation Receiver Isolation vs. Transmitter

LO Frequency

Figure 268. Receiver Integrated Noise Figure vs. Baseband Offset

Frequency, 200 MHz Bandwidth, Sample Rate = 245.76 MSPS,

Integrated in 200 kHz Steps

120

–40

Rx1 TO Rx2

Rx2 TO Rx1

Rx3 TO Rx1

Rx4 TO Rx1

Rx1 TO Rx3

Rx2 TO Rx3

Rx3 TO Rx2

Rx4 TO Rx2

Rx1 TO Rx4

Rx2 TO Rx4

Rx3 TO Rx4

Rx4 TO Rx3

+110°C

+25°C

–40°C

110

100

90

–50

–60

–70

80

–80

70

–90

60

50

3500

–100

3500

3600

3700

3800

3900

4000

3600

3700

3800

3900

4000

RECEIVER LO FREQUENCY (MHz)

Figure 266. Receiver to Receiver Isolation vs. Receiver LO Frequency

Figure 269. Receiver LO Leakage vs. Receiver LO Frequency,

Attenuation = 0 dB, Sample Rate = 245.76 MSPS

Rev. E | Page 71 of 115

ADRV9010

Data Sheet

0.5

0.4

20

15

10

5

+110°C

+25°C

–40°C

0.3

0.2

0.1

0

–0.1

–0.2

–0.3

–0.4

–0.5

5

+110°C, Rx1

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–10

–15

–100 –80 –60 –40 –20

0

20

40

60

80

100

0

5

10

15

20

25

30

BASEBAND OFFSET FREQUENCY (MHz)

RECEIVER ATTENUATION (dB)

Figure 270. Receiver Gain vs. Receiver Attenuation, 20 MHz Offset,

200 MHz Bandwidth, Sample Rate = 245.76 MSPS

Figure 273. Normalized Receiver Flatness vs. Baseband Offset Frequency,

−5 dBFS Input Signal

–40

20

19

18

17

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

–50

–60

–70

–80

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

16

15

–90

–100

–100 –80 –60 –40 –20

0

20

40

60

80

100

3500

3600

3700

3800

3900

4000

BASEBAND OFFSET FREQUENCY (MHz)

RECEIVER LO FREQUENCY (MHz)

Figure 274. Receiver Image vs. Baseband Offset Frequency, Tracking

Calibration Active, Sample Rate = 245.76 MSPS, −5 dBFS Input Signal

Figure 271. Receiver Gain vs. Receiver LO Frequency, 10 MHz Offset,

200 MHz Bandwidth, Sample Rate = 245.76 MSPS

–40

0.20

0.15

0.10

0.05

0

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

–50

–60

–70

–0.05

–0.10

–80

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

–90

–0.15

–0.20

–100

0

5

10

15

20

25

30

0

5

10

15

20

25

30

RECEIVER ATTENUATION (dB)

Figure 272. Receiver Gain Step Error vs. Receiver Attenuation,

20 MHz Offset, −5 dBFS Input Signal

Figure 275. Receiver Image vs. Receiver Attenuation, 20 MHz Offset, Tracking

Calibration Active, Sample Rate = 245.76 MSPS, −5 dBFS Input Signal

Rev. E | Page 72 of 115

Data Sheet

ADRV9010

–40

–50

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

–50

–60

–70

–80

–90

–100

–110

–120

–100

–110

0

5

10

15

20

25

30

–40

–30

–20

–10

0

10

20

30

40

RECEIVER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 276. Receiver DC Offset vs. Receiver Attenuation, 20 MHz Offset,

−5 dBFS Input Signal

Figure 279. Receiver HD3, Left Side vs. Baseband Offset Frequency,

−5 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

–40

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

–50

–60

–50

–60

–70

–80

–90

–100

–110

–120

–100

–110

–120

–60

–40

–20

0

20

40

60

–40

–30

–20

–10

0

10

20

30

40

BASEBAND OFFSET FREQUENCY (MHz)

Figure 277. Receiver HD2, Left Side vs. Baseband Offset Frequency,

−5 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

(HD2 Canceller Not Enabled)

Figure 280. Receiver HD3, Right Side vs. Baseband Offset Frequency,

−5 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

80

–40

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

–50

–60

75

70

65

60

55

50

–70

–80

–90

–100

–110

–120

3805

3815

3825

3835

3845

–60

–40

–20

0

20

40

60

TONE 2 FREQUENCY (MHz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 281. Receiver IIP2, f1 + f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 278. Receiver HD2, Right Side vs. Baseband Offset Frequency,

−5 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

(HD2 Canceller Not Enabled)

Rev. E | Page 73 of 115

ADRV9010

Data Sheet

80

75

70

65

60

100

95

90

85

80

75

70

65

60

+110°C, Rx1

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

55

50

3805 3815 3825 3835 3845 3855 3865 3875 3885 3895

TONE 2 FREQUENCY (MHz)

0

5

10

15

20

25

30

RECEIVER ATTENUATION (dB)

Figure 282. Receiver IIP2, f1 − f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 285. Receiver IIP2, f1 + f2 vs. Receiver Attenuation,

Both Tones at −11 dBFS, f1 = 92 MHz, f2 = 2 MHz

80

75

70

65

60

100

95

90

85

80

75

70

65

60

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

55

50

10

20

30

40

50

60

70

80

90

0

5

10

15

20

25

30

TWO-TONE FREQUENCY SPACING (MHz)

RECEIVER ATTENUATION (dB)

Figure 283. Receiver IIP2, f1 + f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Figure 286. Receiver IIP2, f1 − f2 vs. Receiver Attenuation,

Both Tones at −11 dBFS, f1 = 92 MHz, f2 = 2 MHz

80

75

70

65

60

40

35

30

25

20

15

10

5

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

55

50

10

0

3805

20

30

40

50

60

70

80

90

3810

3815

3820

3825

TWO-TONE FREQUENCY SPACING (MHz)

TONE 2 FREQUENCY (MHz)

Figure 284. Receiver IIP2, f1 − f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Figure 287. Receiver IIP3, 2f1 + f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Rev. E | Page 74 of 115

Data Sheet

ADRV9010

40

35

30

25

20

15

10

5

35

30

25

20

15

10

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

0

3805

3810

3815

3820

3825

10

15

20

25

30

35

40

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 288. Receiver IIP3, 2f2 + f1 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 291. Receiver IIP3, 2f1 + f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

40

35

30

25

20

15

10

5

35

30

25

20

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

15

10

0

3805 3815 3825 3835 3845 3855 3865 3875 3885 3895

10

20

30

40

50

60

70

80

90

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 289. Receiver IIP3, 2f1 − f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 292. Receiver IIP3, 2f2 + f1 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

40

35

30

25

20

15

10

5

35

30

25

20

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

15

0

10

3805 3815 3825 3835 3845 3855 3865 3875 3885 3895

15

20

25

30

35

40

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 290. Receiver IIP3, 2f2 − f1 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 293. Receiver IIP3, 2f1 − f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Rev. E | Page 75 of 115

ADRV9010

Data Sheet

35

30

25

20

–80

–90

–100

–110

–120

–130

–140

–150

+110°C, Rx1

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

15

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

10

100

1k

10k

100k

1M

10M

20

30

40

50

60

70

80

90

FREQUENCY OFFSET (Hz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 297. LO Phase Noise vs. Frequency Offset, Loop Bandwidth =

600 kHz, Phase Margin = 60°

Figure 294. Receiver IIP3, 2f2 − f1 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

50

45

40

35

30

25

20

15

–20

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

–25

–30

–35

–40

–45

–50

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

10

5

0

5

10

15

20

–60 –55 –50 –45 –40 –35 –30 –25 –20 –15 –10 –5

0

5

OBSERVATION RECEIVER ATTENUATION (dB)

RECEIVER INPUT POWER (dBm)

Figure 298. Observation Receiver Integrated Noise Figure vs. Observation

Receiver Attenuation, 20 MHz Offset, 450 MHz Bandwidth, Sample Rate =

491.52 MSPS, Integration Bandwidth = 500 kHz to 100 MHz

Figure 295. Receiver Error Vector Magnitude vs. Receiver Input Power,

20 MHz LTE Signal Centered at LO Frequency, Sample Rate = 245.76 MSPS,

Loop Filter Bandwidth = 600 kHz, Loop Filter Phase Margin = 75°

35

30

25

20

15

–80

–90

–100

–110

–120

–130

–140

–150

10

5

+110°C

+25°C

–40°C

0

–250

100

1k

10k

100k

1M

10M

–150

–50

50

150

250

FREQUENCY OFFSET (Hz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 296. LO Phase Noise vs. Frequency Offset, Loop Bandwidth =

75 kHz, Phase Margin = 85°

Figure 299. Observation Receiver Integrated Noise Figure vs. Baseband

Offset Frequency, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS,

Integrated in 200 kHz Steps

Rev. E | Page 76 of 115

Data Sheet

ADRV9010

–40

–50

–60

–70

–80

–90

–100

0.20

0.15

0.10

0.05

0

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

–0.05

–0.10

–0.15

–0.20

+110°C

+25°C

–40°C

3500

3600

3700

3800

3900

4000

0

5

10

15

20

25

30

OBSERVATION RECEIVER LO FREQUENCY (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 300. Observation Receiver LO Leakage vs. Observation Receiver

LO Frequency, 0 dB Attenuation, Sample Rate = 491.52 MSPS

Figure 303. Observation Receiver Gain Step Error vs. Observation Receiver

Attenuation, 20 MHz Offset, −5 dBFS Input Signal

20

0.5

0.4

0.3

0.2

0.1

0

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

15

10

5

0

–0.1

–0.2

–5

–10

–15

+110°C

+25°C

–0.3

–0.4

–0.5

–40°C

0

5

10

15

20

25

30

–220 –180 –140 –100 –60 –20 20

60 100 140 180 220

OBSERVATION RECEIVER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 301. Observation Receiver Gain vs. Observation Receiver Attenuation,

20 MHz Offset, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS

Figure 304. Normalized Observation Receiver Flatness vs. Baseband

Offset Frequency, −25 dBm Input Signal, 0 dB Attenuation

20

–40

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

–50

–60

19

18

17

16

15

–70

–80

–90

–100

3500

3600

3700

3800

3900

4000

–225 –175 –125 –75

–25

25

75

125

175

225

OBSERVATION RECEIVER LO FREQUENCY (MHz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 302. Observation Receiver Gain vs. Observation Receiver

LO Frequency, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS

Figure 305. Observation Receiver Image vs. Baseband Offset Frequency,

Tracking Calibration Active, Sample Rate = 491.52 MSPS

Rev. E | Page 77 of 115

ADRV9010

Data Sheet

–40

–50

–60

–70

–80

–90

–40

–50

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

–60

–70

–80

–90

–100

–110

–120

–100

0

5

10

15

20

25

30

–60

–40

–20

0

20

40

60

OBSERVATION RECEIVER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 306. Observation Receiver Image vs. Observation Receiver Attenuation,

20 MHz Offset, Tracking Calibration Active, Sample Rate = 491.52 MSPS

Figure 309. Observation Receiver HD3, Left Side vs. Baseband Offset

Frequency, −5 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

–40

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

–50

–60

–50

–60

–70

–80

–90

–100

–110

–120

–100

–110

–120

–100 –80 –60 –40 –20

0

20

40

60

80

100

–60

–40

–20

0

20

40

60

BASEBAND OFFSET FREQUENCY (MHz)

Figure 307. Observation Receiver HD2, Left Side vs. Baseband Offset

Frequency, −5 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

Figure 310. Observation Receiver HD3, Right Side vs. Baseband Offset

Frequency, −5 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

–40

80

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

–50

–60

75

70

65

60

55

50

45

40

–70

–80

–90

–100

–110

–120

–100 –80 –60 –40 –20

0

20

40

60

80

100

3805 3815 3825 3835 3845 3855 3865 3875 3885 3895 3905

BASEBAND OFFSET FREQUENCY (MHz)

TONE 2 FREQUENCY (MHz)

Figure 308. Observation Receiver HD2, Right Side vs. Baseband Offset

Frequency, −5 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

Figure 311. Observation Receiver IIP2, f1 + f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Rev. E | Page 78 of 115

Data Sheet

ADRV9010

80

75

70

65

60

55

50

90

80

70

60

50

40

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

+110°C, ORx1

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

45

40

3805

3835

3865

3895

3925

3955

3985

4015

0

5

10

15

20

25

30

TONE 2 FREQUENCY (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 312. Observation Receiver IIP2, f1 − f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 315. Observation Receiver IIP2, f1 + f2 vs. Observation Receiver

Attenuation, Both Tones at −11 dBFS, f1 = 102 MHz, f2 = 2 MHz

75

70

65

60

55

50

90

80

70

60

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

50

40

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

45

40

10

40

70

100

130

160

190

220

0

5

10

15

20

25

30

TWO-TONE FREQUENCY SPACING (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 313. Observation Receiver IIP2, f1 + f2 vs. Two-Tone Frequency

Spacing, Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Figure 316. Observation Receiver IIP2, f1 − f2 vs. Observation Receiver

Attenuation, Both Tones at −11 dBFS, f1 = 102 MHz, f2 = 2 MHz

75

70

65

60

55

50

40

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

35

30

25

20

15

10

5

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

45

40

0

10

40

70

100

130

160

190

220

3805

3815

3825

3835

3845

3855

3865

TWO-TONE FREQUENCY SPACING (MHz)

TONE 2 FREQUENCY (MHz)

Figure 314. Observation Receiver IIP2, f1 − f2 vs. Two-Tone Frequency

Spacing, Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Figure 317. Observation Receiver IIP3, 2f1 + f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Rev. E | Page 79 of 115

ADRV9010

Data Sheet

40

35

30

25

20

15

10

5

30

25

20

15

10

5

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

0

3805

0

10

3815

3825

3835

3845

3855

3865

20

30

40

50

60

70

80

90

100

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 318. Observation Receiver IIP3, 2f2 + f1 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 321. Observation Receiver IIP3, 2f1 + f2 vs. Two-Tone Frequency

Spacing, Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

40

30

25

20

15

10

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

35

30

25

20

15

10

5

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

5

0

3805

3835

3865

3895

3925

3955

3985

4015

10

30

50

70

90

110 130 150 170 190 210

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 322. Observation Receiver IIP3, 2f2 + f1 vs. Two-Tone Frequency

Spacing, Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Figure 319. Observation Receiver IIP3, 2f1 − f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

40

30

25

20

15

10

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

35

30

25

20

15

10

5

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

5

0

3805

3835

3865

3895

3925

3955

3985

4015

10

30

50

70

90

110

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 320. Observation Receiver IIP3, 2f2 − f1 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 323. Observation Receiver IIP3, 2f1 − f2 vs. Two-Tone Frequency

Spacing, Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Rev. E | Page 80 of 115

Data Sheet

ADRV9010

30

25

20

15

10

5

60

50

40

30

20

10

0

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

0

10

40

70

100

130

160

190

220

0

5

10

15

20

25

30

TWO-TONE FREQUENCY SPACING (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 324. Observation Receiver IIP3, 2f2 − f1 vs. Two-Tone Frequency

Spacing, Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Figure 326. Observation Receiver IIP3, 2f2 − f1 vs. Observation Receiver

Attenuation, Both Tones at −11 dBFS, f1 = 122 MHz, f2 = 2 MHz

60

50

40

30

20

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

10

0

5

10

15

20

25

30

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 325. Observation Receiver IIP3, 2f2 + f1 vs. Observation Receiver

Attenuation, Both Tones at −11 dBFS, f1 = 122 MHz, f2 = 2 MHz

Rev. E | Page 81 of 115

ADRV9010

Data Sheet

4800 MHz BAND

The temperature settings refer to the die temperature. All LO frequencies set to 4800 MHz, unless otherwise noted.

7.0

6.5

6.0

5.5

5.0

4.5

4.0

3.5

3.0

–100

–110

–120

–130

–140

–150

–160

–170

–180

–40°C

+25°C

+110°C

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

4500

4600

4700

4800

4900

5000

0

5

10

15

20

TRANSMITTER LO FREQUENCY (MHz)

TRANSMITTER ATTENUATION (dB)

Figure 327. Transmitter CW Output Power vs. Transmitter LO Frequency,

10 MHz Offset, 0 dB Attenuation

Figure 330. Transmitter Noise vs. Transmitter Attenuation, 50 MHz Offset

1.0

0

–40°C

+25°C

+110°C

SIGNAL

ANALYZER NOISE FLOOR

–10

–20

–30

–40

–50

–60

–70

–80

–90

–100

0.8

0.6

0.4

0.2

0

–0.2

4300 4400 4500 4600 4700 4800 4900 5000 5100 5200 5300

FREQUENCY (MHz)

–250 –200 –150 –100 –50

0

50

100 150 200 250

BASEBAND OFFSET FREQUENCY (MHz)

Figure 328. Transmitter Output Power Spectrum, Tx1, 5 MHz LTE,

10 MHz Offset, −10 dBFS RMS, 1 MHz Resolution Bandwidth, T = 25°C

Figure 331. Transmitter Pass Band Flatness vs. Baseband Offset Frequency

–40

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–40°C

+25°C

+110°C

–45

–50

–55

–60

–65

–70

–75

–80

–100 –80 –60 –40 –20

0

20

40

60

80

100

0

5

10

15

20

BASEBAND OFFSET FREQUENCY (MHz)

TRANSMITTER ATTENUATION (dB)

Figure 329. Transmitter Image Rejection vs. Baseband Offset Frequency, 0 dB

Attenuation, QEC Tracking Enabled

Figure 332. Adjacent Channel Power Level vs. Transmitter Attenuation,

−10 MHz Baseband Offset, 20 MHz LTE, PAR = 12 dB, Loop Filter Bandwidth =

800 kHz, Loop Filter Phase Margin = 75°

Rev. E | Page 82 of 115

Data Sheet

ADRV9010

–40

0.05

0.04

0.03

0.02

0.01

0

–40°C

+25°C

–40°C

+25°C

+110°C

–45

–50

–55

–60

–65

–70

–75

–0.01

–0.02

–0.03

–0.04

–0.05

–80

0

5

10

15

20

0

4

8

12

16

20

24

28

32

TRANSMITTER ATTENUATION (dB)

Figure 333. Adjacent Channel Power Level vs. Transmitter Attenuation,

90 MHz Baseband Offset, 20 MHz LTE, PAR = 12 dB, Loop Filter Bandwidth =

800 kHz, Loop Filter Phase Margin = 75°

Figure 336. Transmitter Attenuator Step Error vs. Transmitter Attenuation,

10 MHz Offset

–60

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–40°C, UPPER HD2

+25°C, UPPER HD2

+110°C, UPPER HD2

–40°C, LOWER HD2

+25°C, LOWER HD2

+110°C, LOWER HD2

–65

–70

–75

–80

–85

–90

–95

–100

–105

–110

0

2

4

6

8

10

12

14

16

18

20

0

2

4

6

8

10

12

14

16

18

20

TRANSMITTER ATTENUATION (dB)

Figure 337. Transmitter Error Vector Magnitude vs. Transmitter Attenuation,

20 MHz LTE Signal Centered at LO Frequency, Sample Rate = 491.52 MSPS,

QEC Tracking Enabled, Loop Filter Bandwidth = 800 kHz,

Loop Filter Phase Margin = 75°

Figure 334. Transmitter HD2 vs. Transmitter Attenuation, 10 MHz Offset

–60

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–40°C, UPPER HD3

+25°C, UPPER HD3

+110°C, UPPER HD3

–40°C, LOWER HD3

+25°C, LOWER HD3

+110°C, LOWER HD3

–65

–70

–75

–80

–85

–90

–95

–100

–105

–110

0

2

4

6

8

10

12

14

16

18

20

0

4

8

12

16

20

24

28

32

TRANSMITTER ATTENUATION (dB)

Figure 338. Transmitter OIP3, 2f1 − f2 vs. Transmitter Attenuation, 15 dB

Digital Backoff per Tone, f1 = 50.5 MHz, f2 = 55.5 MHz

Figure 335. Transmitter HD3 vs. Transmitter Attenuation, 10 MHz Offset

Rev. E | Page 83 of 115

ADRV9010

Data Sheet

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

0

4

8

12

16

20

24

28

32

10

30

50

70

90

110

130

150

170

190

TRANSMITTER ATTENUATION (dB)

f1 BASEBAND OFFSET TONE FREQUENCY (MHz)

Figure 339. Transmitter OIP3, 2f2 − f1 vs. Transmitter Attenuation, 15 dB

Digital Backoff per Tone, f1 = 50.5 MHz, f2 = 55.5 MHz

Figure 342. Transmitter OIP3, 2f1 + f2 vs. f1 Baseband Offset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Backoff per Tone

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

10

30

50

70

90

110

130

150

170

190

10

30

50

70

90

110

130

150

170

190

f1 BASEBAND OFFSET TONE FREQUENCY (MHz)

Figure 340. Transmitter OIP3, 2f1 − f2 vs. f1 Baseband Oﬀset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Backoff per Tone

Figure 343. Transmitter OIP3, 2f2 + f1 vs. f1 Baseband Offset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Backoff per Tone

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

Tx1 TO Tx2

Tx2 TO Tx1

Tx3 TO Tx1

Tx4 TO Tx1

Tx1 TO Tx3

Tx2 TO Tx3

Tx3 TO Tx2

Tx4 TO Tx2

Tx1 TO Tx4

Tx2 TO Tx4

Tx3 TO Tx4

Tx4 TO Tx3

10

30

50

70

90

110

130

150

170

190

4500

4600

4700

4800

4900

5000

f1 BASEBAND OFFSET TONE FREQUENCY (MHz)

TRANSMITTER LO FREQUENCY (MHz)

Figure 344. Transmitter to Transmitter Isolation vs.

Transmitter LO Frequency

Figure 341. Transmitter OIP3, 2f2 − f1 vs. f1 Baseband Oﬀset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Backoff per Tone

Rev. E | Page 84 of 115

Data Sheet

ADRV9010

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

Tx1 TO Rx1

Tx1 TO Rx2

Tx2 TO Rx2

Tx3 TO Rx2

Tx4 TO Rx2

Tx1 TO Rx3

Tx2 TO Rx3

Tx3 TO Rx3

Tx4 TO Rx3

Tx1 TO Rx4

Tx2 TO Rx4

Tx3 TO Rx4

Tx4 TO Rx4

Tx2 TO Rx1

Tx3 TO Rx1

Tx4 TO Rx1

0

5

10

15

20

25

30

4500

4600

4700

4800

4900

5000

RECEIVER ATTENUATION (dB)

RECEIVER LO FREQUENCY (MHz)

Figure 345. Transmitter to Receiver Isolation vs. Receiver LO Frequency

Figure 348. Receiver Integrated Noise Figure vs. Receiver Attenuation,

20 MHz Offset, 200 MHz Bandwidth, Sample Rate = 245.76 MSPS, Integration

Bandwidth = 500 kHz to 100 MHz

25

–40°C

+25°C

+110°C

20

15

10

5

Tx1 TO ORx1

Tx2 TO ORx1

Tx3 TO ORx1

Tx4 TO ORx1

Tx1 TO ORx2

Tx2 TO ORx2

Tx3 TO ORx2

Tx4 TO ORx2

Tx1 TO ORx3

Tx2 TO ORx3

Tx3 TO ORx3

Tx4 TO ORx3

Tx1 TO ORx4

Tx2 TO ORx4

Tx3 TO ORx4

Tx4 TO ORx4

0

4500

4600

4700

4800

4900

5000

–100 –80 –60 –40 –20

0

20

40

60

80

100

TRANSMITTER LO FREQUENCY (MHz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 346. Transmitter to Observation Receiver Isolation vs. Transmitter

LO Frequency

Figure 349. Receiver Integrated Noise Figure vs. Baseband Offset Frequency,

200 MHz Bandwidth, Sample Rate = 245.76 MSPS, Integrated in 200 kHz Steps

–40

–40°C

+25°C

+110°C

–50

–60

–70

Rx1 TO Rx2

Rx2 TO Rx1

Rx3 TO Rx1

Rx4 TO Rx1

Rx1 TO Rx3

Rx2 TO Rx3

Rx3 TO Rx2

Rx4 TO Rx2

Rx1 TO Rx4

Rx2 TO Rx4

Rx3 TO Rx4

Rx4 TO Rx3

–80

–90

–100

4500

4600

4700

4800

4900

5000

4500

4600

4700

4800

4900

5000

RECEIVER LO FREQUENCY (MHz)

Figure 347. Receiver to Receiver Isolation vs. Receiver LO Frequency

Figure 350. Receiver LO Leakage vs. Receiver LO Frequency,

Attenuation = 0 dB, Sample Rate = 245.76 MSPS

Rev. E | Page 85 of 115

ADRV9010

Data Sheet

0.5

0.4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C

+25°C

+110°C

0.3

0.2

0.1

0

–0.1

–0.2

–0.3

–0.4

–0.5

0

5

10

15

20

25

30

–100 –80 –60 –40 –20

0

20

40

60

80

100

RECEIVER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 351. Receiver Gain vs. Receiver Attenuation, 20 MHz Offset, 200 MHz

Bandwidth, Sample Rate = 245.76 MSPS

Figure 354. Normalized Receiver Flatness vs. Baseband Offset Frequency,

−5 dBFS Input Signal

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–100 –80 –60 –40 –20

0

20

40

60

80

100

4500

4600

4700

4800

4900

5000

BASEBAND OFFSET FREQUENCY (MHz)

RECEIVER LO FREQUENCY (MHz)

Figure 352. Receiver Gain vs. Receiver LO Frequency, 10 MHz Offset, 200 MHz

Bandwidth, Sample Rate = 245.76 MSPS

Figure 355. Receiver Image vs. Baseband Offset Frequency,

Tracking Calibration Active, Sample Rate = 245.76 MSPS, −5 dBFS Input Signal

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

0

5

10

15

20

25

30

0

5

10

15

20

25

30

RECEIVER ATTENUATION (dB)

Figure 353. Receiver Gain Step Error vs. Receiver Attenuation,

20 MHz Offset, −5 dBFS Input Signal

Figure 356. Receiver Image vs. Receiver Attenuation, 20 MHz Offset, Tracking

Calibration Active, Sample Rate = 245.76 MSPS, −5 dBFS Input Signal

Rev. E | Page 86 of 115

Data Sheet

ADRV9010

–40°C, Rx1

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

0

5

10

15

20

25

30

–40

–30

–20

–10

0

10

20

30

40

RECEIVER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 357. Receiver DC Offset vs. Receiver Attenuation, 20 MHz Offset,

−5 dBFS Input Signal

Figure 360. Receiver HD3, Left Side vs. Baseband Offset Frequency,

−5 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–60

–40

–20

0

20

40

60

–40

–30

–20

–10

0

10

20

30

40

BASEBAND OFFSET FREQUENCY (MHz)

Figure 361. Receiver HD3, Right Side vs. Baseband Offset Frequency,

−5 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

Figure 358. Receiver HD2, Left Side vs. Baseband Offset Frequency,

−5 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

(HD2 Canceller Not Enabled)

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

4805

4815

4825

4835

4845

–60

–40

–20

0

20

40

60

TONE 2 FREQUENCY (MHz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 362. Receiver IIP2, f1 + f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 359. Receiver HD2, Right Side vs. Baseband Offset Frequency,

−5 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

(HD2 Canceller Not Enabled)

Rev. E | Page 87 of 115

ADRV9010

Data Sheet

–40°C, Rx1

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

4805 4815 4825 4835 4845 4855 4865 4875 4885 4895

TONE 2 FREQUENCY (MHz)

0

5

10

15

20

25

30

RECEIVER ATTENUATION (dB)

Figure 363. Receiver IIP2, f1 − f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 366. Receiver IIP2, f1 + f2 vs. Receiver Attenuation,

Both Tones at −11 dBFS, f1 = 92 MHz, f2 = 2 MHz

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

10

20

30

40

50

60

70

80

90

0

5

10

15

20

25

30

TWO-TONE FREQUENCY SPACING (MHz)

RECEIVER ATTENUATION (dB)

Figure 364. Receiver IIP2, f1 + f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Figure 367. Receiver IIP2, f1 − f2 vs. Receiver Attenuation,

Both Tones at −11 dBFS, f1 = 92 MHz, f2 = 2 MHz

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

10

20

30

40

50

60

70

80

90

4805

4810

4815

4820

4825

TWO-TONE FREQUENCY SPACING (MHz)

TONE 2 FREQUENCY (MHz)

Figure 365. Receiver IIP2, f1 − f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Figure 368. Receiver IIP3, 2f1 + f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Rev. E | Page 88 of 115

Data Sheet

ADRV9010

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

10

15

20

25

30

35

40

4805

4810

4815

4820

4825

TWO-TONE FREQUENCY SPACING (MHz)

TONE 2 FREQUENCY (MHz)

Figure 369. Receiver IIP3, 2f2 + f1 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 372. Receiver IIP3, 2f1 + f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

10

20

30

40

50

60

70

80

90

4805 4815 4825 4835 4845 4855 4865 4875 4885 4895

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 370. Receiver IIP3, 2f1 − f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 373. Receiver IIP3, 2f2 + f1 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

10

15

20

25

30

35

40

4805 4815 4825 4835 4845 4855 4865 4875 4885 4895

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 371. Receiver IIP3, 2f2 − f1 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 374. Receiver IIP3, 2f1 − f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Rev. E | Page 89 of 115

ADRV9010

Data Sheet

–80

–90

–100

–110

–120

–130

–140

–150

–40°C, Rx1

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

10

20

30

40

50

60

70

80

90

100

1k

10k

100k

1M

10M

TWO-TONE FREQUENCY SPACING (MHz)

FREQUENCY OFFSET (Hz)

Figure 375. Receiver IIP3, 2f2 − f1 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Figure 378. LO Phase Noise vs. Frequency Offset, Loop Bandwidth = 400 kHz,

Phase Margin = 60°

50

45

40

35

30

25

20

15

10

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

5

0

5

10

15

20

–60 –55 –50 –45 –40 –35 –30 –25 –20 –15 –10 –5

RECEIVER INPUT POWER (dBm)

0

5

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 379. Observation Receiver Integrated Noise Figure vs. Observation

Receiver Attenuation, 20 MHz Offset, 450 MHz Bandwidth, Sample Rate =

491.52 MSPS, Integration Bandwidth = 500 kHz to 100 MHz

Figure 376. Receiver Error Vector Magnitude vs. Receiver Input Power,

20 MHz LTE Signal Centered at LO Frequency, Sample Rate = 245.76 MSPS,

Loop Filter Bandwidth = 800 kHz, Loop Filter Phase Margin = 75°

35

30

25

20

15

10

–80

–90

–100

–110

–120

–130

–140

–150

5

–40°C

+25°C

+110°C

0

–250

–150

–50

50

150

250

100

1k

10k

100k

1M

10M

BASEBAND OFFSET FREQUENCY (MHz)

FREQUENCY OFFSET (Hz)

Figure 377. LO Phase Noise vs. Frequency Offset, Loop Bandwidth = 75 kHz,

Phase Margin = 85°

Figure 380. Observation Receiver Integrated Noise Figure vs. Baseband Offset

Frequency, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS,

Integrated in 200 kHz Steps

Rev. E | Page 90 of 115

Data Sheet

ADRV9010

–40

–40°C

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C

+110°C

–50

–60

–70

–80

–90

–100

0

5

10

15

20

25

30

4500

4600

4700

4800

4900

5000

OBSERVATION RECEIVER LO FREQUENCY (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 381. Observation Receiver LO Leakage vs. Observation Receiver

LO Frequency, 0 dB Attenuation, Sample Rate = 491.52 MSPS

Figure 384. Observation Receiver Gain Step Error vs. Observation Receiver

Attenuation, 20 MHz Offset, −5 dBFS Input Signal

0.5

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C

+25°C

0.4

+110°C

0.3

0.2

0.1

0

–0.1

–0.2

–0.3

–0.4

–0.5

0

5

10

15

20

25

30

–220 –180 –140 –100 –60 –20 20

60 100 140 180 220

OBSERVATION RECEIVER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 382. Observation Receiver Gain vs. Observation Receiver Attenuation,

20 MHz Offset, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS

Figure 385. Normalized Observation Receiver Flatness vs. Baseband Offset

Frequency, −25 dBm Input Signal, 0 dB Attenuation

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

4500

4600

4700

4800

4900

5000

–225 –175 –125 –75

–25

25

75

125

175

225

OBSERVATION RECEIVER LO FREQUENCY (MHz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 386. Observation Receiver Image vs. Baseband Offset Frequency,

Tracking Calibration Active, Sample Rate = 491.52 MSPS

Figure 383. Observation Receiver Gain vs. Observation Receiver LO

Frequency, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS

Rev. E | Page 91 of 115

ADRV9010

Data Sheet

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

–40°C, ORx1

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

0

5

10

15

20

25

30

–60

–40

–20

0

20

40

60

OBSERVATION RECEIVER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 387. Observation Receiver Image vs. Observation Receiver Attenuation,

20 MHz Offset, Tracking Calibration Active, Sample Rate = 491.52 MSPS

Figure 390. Observation Receiver HD3, Left Side vs. Baseband Offset

Frequency, −5 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–60

–40

–20

0

20

40

60

–100 –80 –60 –40 –20

0

20

40

60

80

100

BASEBAND OFFSET FREQUENCY (MHz)

Figure 388. Observation Receiver HD2, Left Side vs. Baseband Offset

Frequency, −5 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

Figure 391. Observation Receiver HD3, Right Side vs. Baseband Offset

Frequency, −5 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

4805 4815 4825 4835 4845 4855 4865 4875 4885 4895 4905

TONE 2 FREQUENCY(MHz)

–100 –80 –60 –40 –20

0

20

40

60

80

100

BASEBAND OFFSET FREQUENCY (MHz)

Figure 392. Observation Receiver IIP2, f1 + f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 389. Observation Receiver HD2, Right Side vs. Baseband Offset

Frequency, −5 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

Rev. E | Page 92 of 115

Data Sheet

ADRV9010

–40°C, ORx1

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

4805

4835

4865

4895

4925

4955

4985

5015

0

5

10

15

20

25

30

TONE 2 FREQUENCY (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 393. Observation Receiver IIP2, f1 − f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 396. Observation Receiver IIP2, f1 + f2 vs. Observation Receiver

Attenuation, Both Tones at −11 dBFS, f1 = 102 MHz, f2 = 2 MHz

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

10

40

70

100

130

160

190

220

0

5

10

15

20

25

30

TWO-TONE FREQUENCY SPACING (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 394. Observation Receiver IIP2, f1 + f2 vs. Two-Tone Frequency

Spacing, Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Figure 397. Observation Receiver IIP2, f1 − f2 vs. Observation Receiver

Attenuation, Both Tones at −11 dBFS, f1 = 102 MHz, f2 = 2 MHz

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

10

40

70

100

130

160

190

220

4805

4815

4825

4835

4845

4855

4865

TWO-TONE FREQUENCY SPACING (MHz)

TONE 2 FREQUENCY (MHz)

Figure 395. Observation Receiver IIP2, f1 − f2 vs. Two-Tone Frequency

Spacing, Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Figure 398. Observation Receiver IIP3, 2f1 + f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Rev. E | Page 93 of 115

ADRV9010

Data Sheet

–40°C, ORx1

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

4805

4815

4825

4835

4845

4855

4865

10

20

30

40

50

60

70

80

90

100

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 399. Observation Receiver IIP3, 2f2 + f1 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 402. Observation Receiver IIP3, 2f1 + f2 vs. Two-Tone Frequency

Spacing, Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

4805

4835

4865

4895

4925

4955

4985

5015

10

30

50

70

90

110 130 150 170 190 210

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 400. Observation Receiver IIP3, 2f1 − f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 403. Observation Receiver IIP3, 2f2 + f1 vs. Two-Tone Frequency

Spacing, Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

10

30

50

70

90

110

4805

4865

4895

4985

5015

4835

4925

4955

TWO-TONE FREQUENCY SPACING (MHz)

TONE 2 FREQUENCY (MHz)

Figure 401. Observation Receiver IIP3, 2f2 − f1 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 404. Observation Receiver IIP3, 2f1 − f2 vs. Two-Tone Frequency

Spacing, Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Rev. E | Page 94 of 115

Data Sheet

ADRV9010

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

10

40

70

100

130

160

190

220

0

5

10

15

20

25

30

TWO-TONE FREQUENCY SPACING (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 405. Observation Receiver IIP3, 2f2 − f1 vs. Two-Tone Frequency

Spacing, Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Figure 407. Observation Receiver IIP3, 2f2 − f1 vs. Observation Receiver

Attenuation, Both Tones at −11 dBFS, f1 = 122 MHz, f2 = 2 MHz

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

0

5

10

15

20

25

30

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 406. Observation Receiver IIP3, 2f2 + f1 vs. Observation Receiver

Attenuation, Both Tones at −11 dBFS, f1 = 122 MHz, f2 = 2 MHz

Rev. E | Page 95 of 115

ADRV9010

Data Sheet

5700 MHz BAND

The temperature settings refer to the die temperature. All LO frequencies set to 5700 MHz, unless otherwise noted.

7.0

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

6.5

6.0

5.5

5.0

4.5

4.0

3.5

3.0

–40°C

+25°C

+110°C

0

5

10

15

20

5000 5100 5200 5300 5400 5500 5600 5700 5800 5900

TRANSMITTER LO FREQUENCY (MHz)

TRANSMITTER ATTENUATION (dB)

Figure 408. Transmitter CW Output Power vs. Transmitter LO Frequency,

10 MHz Offset, 0 dB Attenuation

Figure 411. Transmitter Noise vs. Transmitter Attenuation,

50 MHz Offset Frequency

0

–40°C

+25°C

+110°C

SIGNAL

ANALYZER NOISE FLOOR

–10

–20

–30

–40

–50

–60

–70

–80

–90

–100

5200

5300

5400

5500

5600

5700

5800

5900

6000

–250 –200 –150 –100 –50

0

50

100 150 200 250

FREQUENCY (MHz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 409. Transmitter Output Power Spectrum, Tx1, 5 MHz LTE,

10 MHz Offset, −10 dBFS RMS, 1 MHz Resolution Bandwidth, T = 25°C

Figure 412. Transmitter Pass Band Flatness vs. Baseband Offset Frequency

–40°C

+25°C

+110°C

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–100 –80 –60 –40 –20

0

20

40

60

80

100

0

5

10

15

20

BASEBAND OFFSET FREQUENCY (MHz)

TRANSMITTER ATTENUATION (dB)

Figure 410. Transmitter Image Rejection vs. Baseband Offset Frequency, 0 dB

Attenuation, QEC Tracking Enabled

Figure 413. Adjacent Channel Power Level vs. Transmitter Attenuation,

−10 MHz Baseband Offset, 20 MHz LTE, PAR = 12 dB, Loop Filter Bandwidth =

500 kHz, Loop Filter Phase Margin = 60°

Rev. E | Page 96 of 115

Data Sheet

ADRV9010

0.05

0.04

0.03

0.02

0.01

0

–40

–40°C

+25°C

+110°C

–40°C

+25°C

+110°C

–45

–50

–55

–60

–65

–70

–75

–80

–0.01

–0.02

–0.03

–0.04

–0.05

0

4

8

12

16

20

24

28

32

0

5

10

15

20

TRANSMITTER ATTENUATION (dB)

Figure 414. Adjacent Channel Power Level vs. Transmitter Attenuation,

90 MHz Baseband Offset, 20 MHz LTE, PAR = 12 dB, Loop Filter Bandwidth =

500 kHz, Loop Filter Phase Margin = 60°

Figure 417. Transmitter Attenuator Step Error vs. Transmitter Attenuation,

10 MHz Offset

–60

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–40°C, UPPER HD2

+25°C, UPPER HD2

+110°C, UPPER HD2

–40°C, LOWER HD2

+25°C, LOWER HD2

+110°C, LOWER HD2

–65

–70

–75

–80

–85

–90

–95

–100

–105

–110

0

2

4

6

8

10

12

14

16

18

20

0

2

4

6

8

10

12

14

16

18

20

TRANSMITTER ATTENUATION (dB)

Figure 418. Transmitter Error Vector Magnitude vs. Transmitter Attenuation,

20 MHz LTE Signal Centered at LO Frequency, Sample Rate = 491.52MSPS, QEC

Tracking Enabled, Loop Filter Bandwidth = 500 kHz,

Figure 415. Transmitter HD2 vs. Transmitter Attenuation, 10 MHz Offset

Loop Filter Phase Margin = 60°

–60

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–40°C, UPPER HD3

+25°C, UPPER HD3

+110°C, UPPER HD3

–40°C, LOWER HD3

+25°C, LOWER HD3

+110°C, LOWER HD3

–65

–70

–75

–80

–85

–90

–95

–100

–105

–110

0

4

8

12

16

20

24

28

32

0

2

4

6

8

10

12

14

16

18

20

TRANSMITTER ATTENUATION (dB)

Figure 419. Transmitter OIP3, 2f1 − f2 vs. Transmitter Attenuation,

15 dB Digital Backoff per Tone, f1 = 50.5 MHz, f2 = 55.5 MHz

Figure 416. Transmitter HD3 vs. Transmitter Attenuation, 10 MHz Offset

Rev. E | Page 97 of 115

ADRV9010

Data Sheet

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

0

4

8

12

16

20

24

28

32

10

30

50

70

90

110

130

150

170

190

TRANSMITTER ATTENUATION (dB)

f1 BASEBAND OFFSET TONE FREQUENCY (MHz)

Figure 420. Transmitter OIP3, 2f2 − f1 vs. Transmitter Attenuation,

15 dB Digital Backoff per Tone, f1 = 50.5 MHz, f2 = 55.5 MHz

Figure 423. Transmitter OIP3, 2f1 + f2 vs. f1 Baseband Offset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Backoff per Tone

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

10

30

50

70

90

110

130

150

170

190

10

30

50

70

90

110

130

150

170

190

f1 BASEBAND OFFSET TONE FREQUENCY (MHz)

Figure 421. Transmitter OIP3, 2f1 − f2 vs. f1 Baseband Oﬀset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Backoff per Tone

Figure 424. Transmitter OIP3, 2f2 + f1 vs. f1 Baseband Offset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Backoff per Tone

Tx1 TO Tx1

Tx2 TO Tx1

Tx3 TO Tx1

Tx4 TO Tx1

Tx1 TO Tx2

Tx2 TO Tx2

Tx3 TO Tx2

Tx4 TO Tx2

Tx1 TO Tx3

Tx2 TO Tx3

Tx3 TO Tx3

Tx4 TO Tx3

Tx1 TO Tx4

Tx2 TO Tx4

Tx3 TO Tx4

Tx4 TO Tx4

–40°C, Tx1

–40°C, Tx2

–40°C, Tx3

–40°C, Tx4

+25°C, Tx1

+25°C, Tx2

+25°C, Tx3

+25°C, Tx4

+110°C, Tx1

+110°C, Tx2

+110°C, Tx3

+110°C, Tx4

10

30

50

70

90

110

130

150

170

190

5000 5100 5200 5300 5400 5500 5600 5700 5800 5900 6000

TRANSMITTER LO FREQUENCY (MHz)

f1 BASEBAND OFFSET TONE FREQUENCY (MHz)

Figure 422. Transmitter OIP3, 2f2 − f1 vs. f1 Baseband Oﬀset Tone Frequency,

f2 = f1 + 5 MHz, 15 dB Digital Backoff per Tone

Figure 425. Transmitter to Transmitter Isolation vs. Transmitter

LO Frequency

Rev. E | Page 98 of 115

Data Sheet

ADRV9010

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

Tx1 TO Rx1

Tx1 TO Rx2

Tx2 TO Rx2

Tx3 TO Rx2

Tx4 TO Rx2

Tx1 TO Rx3

Tx2 TO Rx3

Tx3 TO Rx3

Tx4 TO Rx3

Tx1 TO Rx4

Tx2 TO Rx4

Tx3 TO Rx4

Tx4 TO Rx4

Tx2 TO Rx1

Tx3 TO Rx1

Tx4 TO Rx1

0

5

10

15

20

25

30

5000 5100 5200 5300 5400 5500 5600 5700 5800 5900 6000

RECEIVER LO FREQUENCY (MHz)

RECEIVER ATTENUATION (dB)

Figure 426. Transmitter to Receiver Isolation vs. Receiver LO Frequency

Figure 429. Receiver Integrated Noise Figure vs. Receiver Attenuation,

20 MHz Offset, 200 MHz Bandwidth, Sample Rate = 245.76 MSPS,

Integration Bandwidth = 500 kHz to 100 MHz

25

–40°C

+25°C

+110°C

20

15

10

5

Tx1 TO ORx1

Tx2 TO ORx1

Tx3 TO ORx1

Tx4 TO ORx1

Tx1 TO ORx2

Tx2 TO ORx2

Tx3 TO ORx2

Tx4 TO ORx2

Tx1 TO ORx3

Tx2 TO ORx3

Tx3 TO ORx3

Tx4 TO ORx3

Tx1 TO ORx4

Tx2 TO ORx4

Tx3 TO ORx4

Tx4 TO ORx4

0

5000 5100 5200 5300 5400 5500 5600 5700 5800 5900 6000

TRANSMITTER LO FREQUENCY (MHz)

–100 –80 –60 –40 –20

0

20

40

60

80

100

BASEBAND OFFSET FREQUENCY (MHz)

Figure 427. Transmitter to Observation Receiver Isolation vs. Transmitter

LO Frequency

Figure 430. Receiver Integrated Noise Figure vs. Baseband Offset Frequency,

200 MHz Bandwidth, Sample Rate = 245.76 MSPS, Integrated in 200 kHz Steps

–40

Rx1 TO Rx2

Rx2 TO Rx1

Rx3 TO Rx1

Rx4 TO Rx1

Rx1 TO Rx3

Rx2 TO Rx3

Rx3 TO Rx2

Rx4 TO Rx2

Rx1 TO Rx4

Rx2 TO Rx4

Rx3 TO Rx4

Rx4 TO Rx3

–40°C

+25°C

+110°C

–50

–60

–70

–80

–90

–100

5000 5100 5200 5300 5400 5500 5600 5700 5800 5900 6000

RECEIVER LO FREQUENCY (MHz)

5000 5100 5200 5300 5400 5500 5600 5700 5800 5900 6000

RECEIVER LO FREQUENCY (MHz)

Figure 428. Receiver to Receiver Isolation vs. Receiver LO Frequency

Figure 431. Receiver LO Leakage vs. Receiver LO Frequency,

Attenuation = 0 dB, Sample Rate = 245.76 MSPS

Rev. E | Page 99 of 115

ADRV9010

Data Sheet

0.5

0.4

–40°C

+25°C

+110°C

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

0.3

0.2

0.1

0.0

–0.1

–0.2

–0.3

–0.4

–0.5

0

5

10

15

20

25

30

–100 –80 –60 –40 –20

0

20

40

60

80

100

RECEIVER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 432. Receiver Gain vs. Receiver Attenuation, 20 MHz Offset, 200 MHz

Bandwidth, Sample Rate = 245.76 MSPS

Figure 435. Normalized Receiver Flatness vs. Baseband Offset Frequency,

−5 dBFS Input Signal

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–100 –80 –60 –40 –20

0

20

40

60

80

100

5000 5100 5200 5300 5400 5500 5600 5700 5800 5900 6000

RECEIVER LO FREQUENCY (MHz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 433. Receiver Gain vs. Receiver LO Frequency, 10 MHz Offset, 200 MHz

Bandwidth, Sample Rate = 245.76 MSPS

Figure 436. Receiver Image vs. Baseband Offset Frequency, Tracking Calibration

Active, Sample Rate = 245.76 MSPS, −5 dBFS Input Signal

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

0

5

10

15

20

25

30

0

5

10

15

20

25

30

RECEIVER ATTENUATION (dB)

Figure 434. Receiver Gain Step Error vs. Receiver Attenuation, 20 MHz Offset,

−5 dBFS Input Signal

Figure 437. Receiver Image vs. Receiver Attenuation, 20 MHz Offset,

Tracking Calibration Active, Sample Rate = 245.76 MSPS, −5 dBFS Input Signal

Rev. E | Page 100 of 115

Data Sheet

ADRV9010

–40°C, Rx1

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

0

5

10

15

20

25

30

–40

–30

–20

–10

0

10

20

30

40

RECEIVER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 438. Receiver DC Offset vs. Receiver Attenuation, 20 MHz Offset,

−5 dBFS Input Signal

Figure 441. Receiver HD3, Left Side vs. Baseband Offset Frequency,

−5 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–60

–40

–20

0

20

40

60

–40

–30

–20

–10

0

10

20

30

40

BASEBAND OFFSET FREQUENCY (MHz)

Figure 439. Receiver HD2, Left Side vs. Baseband Offset Frequency,

−5 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

(HD2 Canceller Not Enabled)

Figure 442. Receiver HD3, Right Side vs. Baseband Offset Frequency,

−5 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–60

–40

–20

0

20

40

60

5705

5715

5725

5735

5745

BASEBAND OFFSET FREQUENCY (MHz)

TONE 2 FREQUENCY (MHz)

Figure 443. Receiver IIP2, f1 + f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 440. Receiver HD2, Right Side vs. Baseband Offset Frequency,

−5 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

(HD2 Canceller Not Enabled)

Rev. E | Page 101 of 115

ADRV9010

Data Sheet

–40°C, Rx1

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

0

5

10

15

20

25

30

5705 5715 5725 5735 5745 5755 5765 5775 5785 5795

TONE 2 FREQUENCY (MHz)

RECEIVER ATTENUATION (dB)

Figure 444. Receiver IIP2, f1 − f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 447. Receiver IIP2, f1 + f2 vs. Receiver Attenuation,

Both Tones at −11 dBFS, f1 = 92 MHz, f2 = 2 MHz

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

10

20

30

40

50

60

70

80

90

0

5

10

15

20

25

30

TWO-TONE FREQUENCY SPACING (MHz)

RECEIVER ATTENUATION (dB)

Figure 448. Receiver IIP2, f1 − f2 vs. Receiver Attenuation,

Both Tones at −11 dBFS, f1 = 92 MHz, f2 = 2 MHz

Figure 445. Receiver IIP2, f1 + f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

40

35

30

25

20

15

10

5

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

0

10

20

30

40

50

60

70

80

90

5705

5710

5715

5720

5725

TWO-TONE FREQUENCY SPACING (MHz)

TONE 2 FREQUENCY (MHz)

Figure 446. Receiver IIP2, f1 − f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Figure 449. Receiver IIP3, 2f1 + f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Rev. E | Page 102 of 115

Data Sheet

ADRV9010

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

10

15

20

25

30

35

40

5705

5710

5715

5720

5725

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 450. Receiver IIP3, 2f2 + f1 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 453. Receiver IIP3, 2f1 + f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

5705

5715

5725

5735

5745

5755

5765

5775

5785

10

20

30

40

50

60

70

80

90

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 451. Receiver IIP3, 2f1 − f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 454. Receiver IIP3, 2f2 + f1 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

5705 5715 5725 5735 5745 5755 5765 5775 5785 5795

TONE 2 FREQUENCY (MHz)

10

15

20

25

30

35

40

TWO-TONE FREQUENCY SPACING (MHz)

Figure 452. Receiver IIP3, 2f2 − f1 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 455. Receiver IIP3, 2f1 − f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Rev. E | Page 103 of 115

ADRV9010

Data Sheet

–80

–90

–40°C, Rx1

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

–100

–110

–120

–130

–140

–150

10

20

30

40

50

60

70

80

90

100

1k

10k

100k

1M

10M

TWO-TONE FREQUENCY SPACING (MHz)

FREQUENCY OFFSET (Hz)

Figure 456. Receiver IIP3, 2f2 − f1 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Figure 459. LO Phase Noise vs. Frequency Offset, Loop Bandwidth = 500 kHz,

Phase Margin = 60°

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, Rx1

–40°C, Rx2

–40°C, Rx3

–40°C, Rx4

+25°C, Rx1

+25°C, Rx2

+25°C, Rx3

+25°C, Rx4

+110°C, Rx1

+110°C, Rx2

+110°C, Rx3

+110°C, Rx4

0

5

10

15

20

–60 –55 –50 –45 –40 –35 –30 –25 –20 –15 –10 –5

RECEIVER INPUT POWER (dBm)

0

5

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 457. Receiver Error Vector Magnitude vs. Receiver Input Power, 20 MHz

LTE Signal Centered at LO Frequency, Sample Rate = 245.76 MSPS,

Loop Filter Bandwidth = 500 kHz, Loop Filter Phase Margin = 60°

Figure 460. Observation Receiver Integrated Noise Figure vs. Observation Receiver

Attenuation, 20 MHz Offset, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS,

Integration Bandwidth = 500 kHz to 100 MHz

40

35

30

25

20

15

10

–80

–90

–100

–110

–120

–130

–140

–150

5

–40°C

+25°C

+110°C

0

–250

–150

–50

50

150

250

100

1k

10k

100k

1M

10M

BASEBAND OFFSET FREQUENCY (MHz)

FREQUENCY OFFSET (Hz)

Figure 458. LO Phase Noise vs. Frequency Offset, Loop Bandwidth = 75 kHz,

Phase Margin = 85°

Figure 461. Observation Receiver Integrated Noise Figure vs. Baseband Offset

Frequency, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS,

Integrated in 200 kHz Steps

Rev. E | Page 104 of 115

Data Sheet

ADRV9010

–40

–40°C

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+25°C

+110°C

–50

–60

–70

–80

–90

–100

5000 5100 5200 5300 5400 5500 5600 5700 5800 5900 6000

0

5

10

15

20

25

30

OBSERVATION RECEIVER LO FREQUENCY (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 462. Observation Receiver LO Leakage vs. Observation Receiver

LO Frequency, 0 dB Attenuation, Sample Rate = 491.52 MSPS

Figure 465. Observation Receiver Gain Step Error vs. Observation Receiver

Attenuation, 20 MHz Offset, −5 dBFS Input Signal

0.5

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C

+25°C

0.4

+110°C

0.3

0.2

0.1

0

–0.1

–0.2

–0.3

–0.4

–0.5

0

5

10

15

20

25

30

–220 –180 –140 –100 –60 –20 20

60 100 140 180 220

OBSERVATION RECEIVER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 463. Observation Receiver Gain vs. Observation Receiver Attenuation,

20 MHz Offset, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS

Figure 466. Normalized Observation Receiver Flatness vs. Baseband Offset

Frequency, −25 dBm Input Signal, 0 dB Attenuation

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

5000 5100 5200 5300 5400 5500 5600 5700 5800 5900 6000

OBSERVATION RECEIVER LO FREQUENCY (MHz)

–225 –175 –125 –75

–25

25

75

125

175

225

BASEBAND OFFSET FREQUENCY (MHz)

Figure 464. Observation Receiver Gain vs. Observation Receiver

LO Frequency, 450 MHz Bandwidth, Sample Rate = 491.52 MSPS

Figure 467. Observation Receiver Image vs. Baseband Offset Frequency,

Tracking Calibration Active, Sample Rate = 491.52 MSPS

Rev. E | Page 105 of 115

ADRV9010

Data Sheet

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

–40°C, ORx1

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

0

5

10

15

20

25

30

–60

–40

–20

0

20

40

60

OBSERVATION RECEIVER ATTENUATION (dB)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 468. Observation Receiver Image vs. Observation Receiver Attenuation,

20 MHz Offset, Tracking Calibration Active, Sample Rate = 491.52 MSPS

Figure 471. Observation Receiver HD3, Left Side vs. Baseband Offset

Frequency, −5 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–100 –80 –60 –40 –20

0

20

40

60

80

100

–60

–40

–20

0

20

40

60

BASEBAND OFFSET FREQUENCY (MHz)

Figure 469. Observation Receiver HD2, Left Side vs. Baseband Offset

Frequency, −5 dBFS Input Signal, Distortion Tone Measured Left of 0 Hz

Figure 472. Observation Receiver HD3, Right Side vs. Baseband Offset

Frequency, −5 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

–40°C, ORX1

–40°C, ORX2

–40°C, ORX3

–40°C, ORX4

+25°C, ORX1

+25°C, ORX2

+25°C, ORX3

+25°C, ORX4

+110°C, ORX1

+110°C, ORX2

+110°C, ORX3

+110°C, ORX4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–100 –80 –60 –40 –20

0

20

40

60

80

100

5705 5715 5725 5735 5745 5755 5765 5775 5785 5795 5805

TONE 2 FREQUENCY(MHz)

BASEBAND OFFSET FREQUENCY (MHz)

Figure 473. Observation Receiver IIP2, f1 + f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 470. Observation Receiver HD2, Right Side vs. Baseband Offset

Frequency, −5 dBFS Input Signal, Distortion Tone Measured Right of 0 Hz

Rev. E | Page 106 of 115

Data Sheet

ADRV9010

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

0

5

10

15

20

25

30

5705

5735

5765

5795

5825

5855

5885

5915

OBSERVATION RECEIVER ATTENUATION (dB)

TONE 2 FREQUENCY (MHz)

Figure 474. Observation Receiver IIP2, f1 − f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 477. Observation Receiver IIP2, f1 + f2 vs. Observation Receiver

Attenuation, Both Tones at −11 dBFS, f1 = 102 MHz, f2 = 2 MHz

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

10

40

70

100

130

160

190

220

0

5

10

15

20

25

30

TWO–TONE FREQUENCY SPACING (MHz)

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 475. Observation Receiver IIP2, f1 + f2 vs. Two-Tone Frequency

Spacing, Both Tones at −11 dBFS, f2 = 2 MHz

Figure 478. Observation Receiver IIP2, f1 − f2 vs. Observation Receiver

Attenuation, Both Tones at −11 dBFS, f1 = 102 MHz, f2 = 2 MHz

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

10

40

70

100

130

160

190

220

5705

5715

5725

5735

5745

5755

5765

TWO-TONE FREQUENCY SPACING (MHz)

TONE 2 FREQUENCY (MHz)

Figure 476. Observation Receiver IIP2, f1 − f2 vs. Two-Tone Frequency

Spacing, Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Figure 479. Observation Receiver IIP3, 2f1 + f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Rev. E | Page 107 of 115

ADRV9010

Data Sheet

–40°C, ORx1

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

10

20

30

40

50

60

70

80

90

100

5705

5715

5725

5735

5745

5755

5765

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 480. Observation Receiver IIP3, 2f2 + f1 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 483. Observation Receiver IIP3, 2f1 + f2 vs. Two-Tone Frequency

Spacing, Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

10

30

50

70

90

110 130 150 170 190 210

5705

5735

5765

5795

5825

5855

5885

5915

TWO-TONE FREQUENCY SPACING (MHz)

TONE 2 FREQUENCY (MHz)

Figure 481. Observation Receiver IIP3, 2f1 − f2 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 484. Observation Receiver IIP3, 2f2 + f1 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

10

30

50

70

90

110

5705

5735

5765

5795

5825

5855

5885

5915

TONE 2 FREQUENCY (MHz)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 482. Observation Receiver IIP3, 2f2 − f1 vs. Tone 2 Frequency,

Both Tones at −11 dBFS, 0 dB Attenuation, f1 = f2 + 2 MHz

Figure 485. Observation Receiver IIP3, 2f1 − f2 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Rev. E | Page 108 of 115

Data Sheet

ADRV9010

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx1

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

0

5

10

15

20

25

30

10

40

70

100

130

160

190

220

OBSERVATION RECEIVER ATTENUATION (dB)

TWO-TONE FREQUENCY SPACING (MHz)

Figure 486. Observation Receiver IIP3, 2f2 − f1 vs. Two-Tone Frequency Spacing,

Both Tones at −11 dBFS, 0 dB Attenuation, f2 = 2 MHz

Figure 488. Observation Receiver IIP3, 2f2 − f1 vs. Observation Receiver

Attenuation, Both Tones at −11 dBFS, f1 = 122 MHz, f2 = 2 MHz

–40°C, ORx1

–40°C, ORx2

–40°C, ORx3

–40°C, ORx4

+25°C, ORx1

+25°C, ORx2

+25°C, ORx3

+25°C, ORx4

+110°C, ORx1

+110°C, ORx2

+110°C, ORx3

+110°C, ORx4

0

5

10

15

20

25

30

OBSERVATION RECEIVER ATTENUATION (dB)

Figure 487. Observation Receiver IIP3, 2f2 + f1 vs. Observation Receiver

Attenuation, Both Tones at −11 dBFS, f1 = 122 MHz, f2 = 2 MHz

Rev. E | Page 109 of 115

ADRV9010

Data Sheet

THEORY OF OPERATION

by matched I and Q mixers that downconvert received signals

to baseband for digitization.

GENERAL

The ADRV9010 is a highly integrated RF transceiver capable of

being configured for a wide range of applications. The device

integrates all the RF, mixed-signal, and digital blocks necessary

to provide all transmitter, traffic receiver, and observation

receiver functions in a single device. Programmability allows

the device to be adapted for use in various TDD systems using

3G/4G/5G cellular standards.

Two gain control options are available. Users can implement

their own gain control algorithms by using their baseband

processor to manage manual gain control mode, or users can use

the on-chip automatic gain control (AGC) system. Performance

is optimized by mapping each gain control setting to specific

attenuation levels at each adjustable gain block in the receive

signal path. Additionally, each channel contains independent

receive signal strength indication (RSSI) measurement

capability, dc offset tracking, and all the circuitry necessary

for self-calibration.

Four observation receiver channels are included to monitor

the transmitter outputs and to provide tracking correction of

dc offset, quadrature error, and transmitter LO leakage to maintain

a high performance level under varying temperatures and input

signal conditions. Firmware supplied with the device implements

all initialization and calibration with no user interaction.

Additionally, the device includes test modes allowing system

designers to debug designs during prototyping and to optimize

radio configurations.

The receivers include ADCs and adjustable sample rates that

produce data streams from the received signals. The signals can

be conditioned further by a series of decimation filters and a

programmable FIR filter with additional decimation settings.

The sample rate of each digital filter block is adjustable by

changing decimation factors to produce the desired output data

rate. The receiver outputs are all connected to the SERDES block,

where the data is formatted and serialized for transmission to the

baseband processor.

The ADRV9010 contains eight high speed serial interface

(SERDES) links for the transmit chain and eight high speed

links shared by the receiver and observation receiver chains

(JESD204B Subclass 1 compliant and JESD204C supported).

OBSERVATION RECEIVER

TRANSMITTER

The ADRV9010 provides four independent observation

receiver inputs. These inputs are similar in implementation to the

standard receiver channels in terms of the mixers, ADCs, and

filtering blocks. The main difference is that these receivers are

designed to operate with an observation bandwidth up to

450 MHz, allowing the receivers to receive all the transmitter

channel information needed for implementing digital

correction algorithms.

The ADRV9010 transmitter section consists of four identical

and independently controlled channels that provide all the

digital processing, mixed-signal, and RF blocks necessary to

implement a direct conversion system while sharing a common

frequency synthesizer. The digital data from the SERDES lanes

pass through a digital processing block that includes a series

of programmable half-band filters, interpolation stages, and

FIR filters, including a programmable FIR filter with variable

interpolation rates and up to 80 taps. The output of this digital

chain is connected to the DAC. The DAC sample rate is

adjustable up to 2.5 GHz. The in phase (I) and quadrature

(Q) channels are identical in each transmitter signal chain.

Each input is used as the feedback monitor channel for a

corresponding transmitter channel. Table 11 shows the possible

combinations of transmitter and observation channels.

Table 11. Possible Transmitter/Observation Channel

Combinations

After conversion to baseband analog signals, the I and Q signals are

filtered to remove sampling artifacts and fed to the upconversion

mixers. Each transmit chain provides a wide attenuation

adjustment range with fine granularity to help designers

optimize signal-to-noise ratio (SNR).

Transmitter Channel

Observation Channel

ORX1 or ORX2

ORX3 or ORX4

TX1

TX2

TX3

TX4

RECEIVER

The ADRV9010 provides four independent receiver channels.

Each channel contains all the blocks necessary to receive RF

signals and to convert these signals to digital data usable by a

baseband processor. Each receiver can be configured as a direct

conversion system that supports up to a 200 MHz bandwidth.

Each channel contains a programmable attenuator stage, followed

The observation receiver channels can either share a common

frequency synthesizer with the transmitters or use the auxiliary

synthesizer to offset the LO frequency from the transmitter

channel being monitored.

Rev. E | Page 110 of 115

Data Sheet

ADRV9010

External LO Inputs

CLOCK INPUT

The ADRV9010 provides two external LO inputs to allow an

external synthesizer to be used with the device. These inputs

must be 2× the desired LO frequency. One input is multiplexed

with the RF1 PLL, and the other input is multiplexed with the

RF2 PLL. Each observation receiver can obtain the LO from

either the same input as the associated transmitter channel or

the corresponding, dedicated PLL.

The ADRV9010 requires a differential clock connected to the

DEVCLK pins. The frequency of the clock input signal must

be between 15 MHz and 1000 MHz and must have low phase

noise because this signal generates the RF LO and internal

sampling clocks.

SYNTHESIZERS

The ADRV9010 contains four fractional-N PLLs to generate

the RF LO for the signal paths and all internal clock sources.

This group of PLLs includes two RF PLLs for the transmit and

receive LO generation, an auxiliary PLL that can be used by

the observation receivers, and a clock PLL. Each PLL is

independently controlled with no need for external

components to set frequencies.

SPI INTERFACE

The ADRV9010 uses a SPI to communicate with the baseband

processor. This interface can either be configured as a 4-wire

interface with dedicated receive and transmit ports, or as a

3-wire interface with a bidirectional data communications port.

This SPI allows the baseband processor to set all device control

parameters using a simple address data serial bus protocol.

RF Synthesizers

Write commands follow a 24-bit format. The first bit sets the

bus direction of the bus transfer. The next 15 bits set the

address where data is written. The final eight bits are the data

being transferred to the specific register address.

The two RF synthesizers use fractional-N PLLs to generate RF

LOs for the multiple receiver and transmitter channels. This

PLL incorporates a four-core internal VCO and loop filter,

capable of generating low phase noise signals with no external

components required. An internal LO multiplexer (mux) enables

each PLL to supply LOs to any or all receivers and transmitters

(for example, LO1 to all transmitters and LO2 to all receivers),

resulting in maximum flexibility when configuring the device

for TDD operation. The LOs on multiple devices can be phase

synchronized to support active antenna systems and beam

forming applications.

Read commands follow a similar format with the exception that

the first 16 bits are transferred on the SPI_DIO pin, and the final

eight bits are read from the ADRV9010, either on the SPI_DO

pin in 4-wire mode or on the SPI_DIO pin in 3-wire mode.

POWER SUPPLY SEQUENCE

The ADRV9010 requires a specific power-up sequence to avoid

undesired power-up currents. In the optimal power-up sequence,

the VDIG_1P0 supply is activated first. If the same supply is

used to power the VDDA_1P0 supply, then all 1.0 V supplies

can be powered on at the same time.

Auxiliary Synthesizer

The auxiliary synthesizer uses a single core VCO fractional-N

PLL to generate the signals necessary to calibrate the device.

The output of this block uses a separate mux system to route

LOs for calibrating different functions during initialization.

The auxiliary synthesizer can also be used to generate LO

signals for the observation receivers or as an offset LO used in

the receiver signal chains.

If the VDIG_1P0 supply is isolated, all VDDA_1P8, VDDA_1P3,

and VDDA_1P0 supplies must be powered up after the VDIG_1P0

supply is activated. The VIF supply can be powered up at any

time.

RESET

It is also recommended to toggle the

has stabilized prior to configuration.

signal after power

Clock Synthesizer

The ADRV9010 contains a single core VCO fractional-N PLL

synthesizer that generates all baseband related clock signals and

SERDES clocks. This PLL is programmed based on the data

rate and sample rate requirements of the system, which

typically require the synthesizer to operate in integer mode.

If a power-down sequence is followed, avoid any back biasing

of the digital control lines by removing the VDIG_1P0 supply

last. If no sequencing is used, it is recommended to power

down all supplies simultaneously.

For JESD204B configurations with Np = 12 and JESD204C

configurations, a dedicated PLL included in the SERDES block

generates the SERDES clocks.

Rev. E | Page 111 of 115

ADRV9010

Data Sheet

GPIO_x PINS

JTAG BOUNDARY SCAN

The ADRV9010 provides 19 GPIOs referenced to VIF that can

be configured for numerous functions. When configured as

outputs, certain pins can provide real-time signal information

to the baseband processor, allowing the baseband processor to

determine receiver performance. A pointer register selects what

information is output to these pins.

The ADRV9010 provides support for a JTAG boundary scan.

There are five dual-function pins associated with the JTAG

interface. These pins, listed in Table 12, are used to access the

on-chip test access port. To enable the JTAG functionality,

set the GPIO_0 through GPIO_2 pins according to Table 13

depending on how the desired JESD204B sync signals are

configured in the software (differential or single-ended mode).

Pull the TEST_EN pin high to the VIF supply to enable the

JTAG mode.

Signals used for manual gain mode, calibration flags, state

machine status, and various receiver parameters are among

the outputs that can be monitored on these pins. Additionally,

certain pins can be configured as inputs and used for various

functions such as setting the receiver gain in real time.

Table 12. Dual-Function Boundary Scan Test Pins

Mnemonic JTAG Mnemonic Description

AUXILIARY CONVERTERS

GPIO_14

TRST

Test access port reset

GPIO_ANA_x/AUXDAC_x

GPIO_15

GPIO_16

GPIO_17

GPIO_18

TDO

TDI

TMS

TCK

Test data output

Test data input

Test access port mode select

Test clock

The ADRV9010 contains eight analog GPIOs (the GPIO_ANA_x

pins) that are multiplexed with eight identical auxiliary DACs

(AUXDAC_x). The analog GPIO ports can be used to control

other analog devices or receive control inputs referenced to

the VDDA_1P8 supply. The auxiliary DACs are 12-bit converters

capable of supplying up to 10 mA. These outputs are typically

used to supply bias current or variable control voltages for

other related components with analog control inputs.

Table 13. JTAG Modes

Test Pin Level GPIO_2 to GPIO_0 Description

0

1

xxx¹

000

Normal operation

JTAG mode with

differential JESD204B sync

signals

JTAG mode with single-

ended JESD204B sync

signals

AUXADC_x

The ADRV9010 contains two auxiliary ADCs with four total input

pins (AUXADC_x). These auxiliary ADCs provide 10-bit

monotonic outputs with an input voltage range of 0.05 V to

0.95 V. When enabled, each auxiliary ADC is free running.

An application programing interface (API) command latches

the ADC output value to a register. The ADRV9010 also contains

an ADC that supports a built-in diode-based temperature sensor.

1

011

¹x means any combination.

Rev. E | Page 112 of 115

Data Sheet

ADRV9010

APPLICATIONS INFORMATION

POWER SUPPLY SEQUENCE

DATA INTERFACE

The digital data interface for the ADRV9010 implements the

JEDEC Standard JESD204B Subclass 1 and JESD204C. The

serial interface operates at speeds of up to 14.7456 Gbps in

JESD204B mode and 16.22016 Gbps in JESD204C mode.

The ADRV9010 requires a specific power-up sequence to avoid

undesired power-up currents. In the optimal power-up sequence,

the VDIG_1P0 supply is activated first. When VDIG_1P0

powers VDDA_1P0, all 1.0 V supplies can be powered on at the

same time.

Table 14, Table 15, and Table 16 list example parameters for

various JESD204x interface settings.

When VDIG_1P0 is isolated, all VDDA_1P8, VDDA_1P3, and

VDDA_1P0 supplies must be powered up after VDIG_1P0 is

activated. The VIF supply can be powered up at any time.

It is also recommended prior to configuration to toggle the

RESET

signal after power has stabilized.

If a power-down sequence is followed, to avoid any back

biasing of the digital control lines, remove the VDIG_1P0

supply last. If no sequencing is used, it is recommended to

power down all supplies simultaneously.

Rev. E | Page 113 of 115

ADRV9010

Data Sheet

Table 14. Example Receiver Interface Rates with Four Channels Active (M = 8)¹

JESD204B JESD204B

JESD204C JESD204C

Lane Rate Number

Bandwidth Output Rate

JESD204x Np

Parameter

JESD204B F Lane Rate

Number of

Lanes

JESD204C F

Parameter

16

8

(MHz)

(MSPS)

Parameter

(Mbps)

9830.4

12288

(Mbps)

of Lanes

40

60

100

150

200

61.44

76.8

122.88

184.32

245.76

16

12

16

8

4

1

2

4

2

8110.08

10137.6

16220.16

12165.12

16220.16

12165.12

1

2

9830.4

14745.6

9830.4

14745.6

8

6

¹Other output rates, bandwidth, and number of lanes also supported.

Table 15. Transmitter Interface Rates with Four Channels Active (M = 8)¹

Primary Signal Total

Input

JESD204x

Np

Parameter Parameter (Mbps)

16

JESD204B

F

JESD204B JESD204B JESD204C

Lane Rate Number

JESD204C JESD204C

Lane Rate Number

Bandwidth

(MHz)

50

Bandwidth Rate

(MHz)

113

F

(MSPS)

of Lanes

Parameter (Mbps)

of Lanes

122.88

184.32

245.76

368.64

491.52

8

4

2

9830.4

14745.6

9830.4

14745.6

9830.4

2

4

8

16

8

4

16220.16

12165.12

16220.16

12165.12

16220.16

1

2

4

75

150

100

150

200

225

300

450

¹Other output rates, bandwidth, and number of lanes also supported.

Table 16. Observation Path Interface Rates with 1 Channel Active (M = 2)¹

JESD204x

Np

JESD204B JESD204B

JESD204B F Lane Rate Number

JESD204C JESD204C

JESD204C F Lane Rate Number of

Total Bandwidth Output Rate

(MHz)

150

220

250

300

450

(MSPS)

184.32

245.76

307.2

368.64

491.52

Parameter Parameter

(Mbps)

7372.8

9830.4

12288

14745.6

9830.4

14745.6

of Lanes

Parameter

(Mbps)

6082.56

8110.08

10137.6

6082.56

8110.08

12165.12

Lanes

16

12

4

2

3

1

2

1

4

2

3

1

2

1

¹Other output rates, bandwidth, and number of lanes also supported.

Rev. E | Page 114 of 115

Data Sheet

ADRV9010

OUTLINE DIMENSIONS

14.10

14.00 SQ

13.90

A1 BALL

CORNER

A1 BALL

CORNER

16 14 12 10

17 15 13 11

8

6

4

2

9

7

5

3

1

Solder Mask

Dam

A

C

E

B

D

F

BALL A1

INDICATOR

G

H

8.704

REF

12.80 REF

SQ

J

K

M

P

T

10.78

L

0.80

N

R

U

0.675

0.600

0.525

TOP VIEW

BOTTOM VIEW

8.744 REF

10.44

1.04

1.00

0.96

DETAIL A

1.43

1.34

1.25

DETAIL A

0.39

0.34

0.29

0.60 REF

SEATING

PLANE

0.50

0.45

0.40

COPLANARITY

0.12

BALL DIAMETER

COMPLIANT TO JEDEC STANDARDS MO-275-JJAB-1

Figure 489. 289-Ball Chip Scale Package Ball Grid Array [CSP_BGA]

(BC-289-3)

Dimensions shown in millimeters

ORDERING GUIDE

Model¹

Temperature Range

Package Description

Package Option

BC-289-3

ADRV9010BBCZ

−40°C to +110°C

289-Ball Chip Scale Package Ball Grid Array [CSP_BGA]

High Band Evaluation Board for 2.8 GHz to 6 GHz

Mid Band Evaluation Board for 650 MHz to 2.8 GHz

ADRV9010BBCZ-REEL

ADRV9010BBCZ-A

ADRV9010BBCZ-A-RL

ADRV9026-HB/PCBZ

ADRV9026-MB/PCBZ

¹Z = RoHS Compliant Part.

registered trademarks are the property of their respective owners.

D20043-1/21(E)

Rev. E | Page 115 of 115


型号：	ADRV9010BBCZ
厂家：	ADI
描述：	Integrated, Quad RF Transceiver with Observation Path
文件：	总115页 (文件大小：2220K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

ADRV9010BBCZ [ADI]

相关型号：

ADRV9010BBCZ-A

ADRV9010BBCZ-A-RL

ADRV9010BBCZ-REEL

ADRV9026-HB/PCBZ

ADRV9026-MB/PCBZ

ADRV9029

ADRV9029-HB/PCBZ

ADRV9029-LB/PCBZ

ADRV9029-MB/PCBZ

ADRV9029BBCZ

ADRV9029BBCZ-REEL

ADRZ01ARZ