EV-ADF5901SD2Z [ADI]
EVAL BOARD ADF5901 DOWNCONVERTER;
| 型号： | EV-ADF5901SD2Z |
| 厂家： | 
ADI |
| 描述： | EVAL BOARD ADF5901 DOWNCONVERTER |
| 文件： | 总18页 (文件大小：1000K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
EV-ADF5901SD2Z Evaluation Board User Guide
UG-864
One Technology Way • P. O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com
Evaluating the ADF5901 24 GHz Voltage Controlled Oscillator (VCO) and
Programmable Gain Amplifier (PGA) with a 2-Channel Power Amplifier (PA) Output
FEATURES
GENERAL DESCRIPTION
Contains ADF5901 24 GHz VCO and PGA with a 2-channel
PA output
Contains ADF4159 13 GHz fractional-N frequency synthesizer
Accompanying software allows control of the ADF5901 and
the ADF4159 functions from a PC
The EV-ADF5901SD2Z evaluation board allows the user
to evaluate the performance of the ADF5901 24 GHz VCO
and PGA with a 2-channel PA output. Figure 1 shows the
EV-ADF5901SD2Z, which contains the ADF5901, the ADF4159,
three high frequency, K-type SMA connectors for the local
oscillator (LO) output and two transceiver (Tx) outputs, two
EVALUATION KIT CONTENTS
EV-ADF5901SD2Z evaluation board
AUX
high frequency SMA connectors for the AUX and the
outputs, banana connectors for power supply, and a connector
for the serial interface.
ADDITIONAL EQUIPMENT
PC running Windows® XP or more recent version
Analog Devices, Inc., EVAL-SDP-CS1Z system demonstration
platform serial (SDP-S) board
Spectrum analyzer
Oscilloscope (optional)
The EV-ADF5901SD2Z evaluation kit also contains software
that is compatible with Windows XP and later versions to allow
easy programming of the device.
The EV-ADF5901SD2Z evaluation board requires an EVAL-
SDP-CS1Z (SDP-S) controller board, which is not supplied with
the kit. The EVAL-SDP-CS1Z allows software programming of
the ADF5901 device.
5 V power supply
DOCUMENTS NEEDED
ADF5901 data sheet
Full specifications on the ADF5901 are available in the ADF5901
data sheet, which should be consulted in conjunction with this
user guide when working with the evaluation board.
REQUIRED SOFTWARE
Analog Devices ADF5901 software
EV-ADF5901SD2Z EVALUATION BOARD PICTURE
Figure 1.
PLEASE SEE THE LAST PAGE FOR AN IMPORTANT
WARNING AND LEGAL TERMS AND CONDITIONS.
Rev. 0 | Page 1 of 18
UG-864
EV-ADF5901SD2Z Evaluation Board User Guide
TABLE OF CONTENTS
Features .............................................................................................. 1
Input Signals...................................................................................3
Output Signals ...............................................................................3
Default Operation .........................................................................3
Evaluation Board Quick Start Procedures .....................................4
EV-ADF5901SD2Z Control Software.........................................4
Evaluation and Testing......................................................................8
Evaluation Board Schematics and Artwork...................................9
Ordering Information.................................................................... 17
Bill of Materials........................................................................... 17
Related Links............................................................................... 18
Evaluation Kit Contents................................................................... 1
Additional Equipment ..................................................................... 1
Documents Needed.......................................................................... 1
Required Software ............................................................................ 1
General Description......................................................................... 1
EV-ADF5901SD2Z Evaluation Board Picture.............................. 1
Revision History ............................................................................... 2
Evaluation Board Hardware............................................................ 3
Power Supplies .............................................................................. 3
REVISION HISTORY
12/15—Revision 0: Initial Version
Rev. 0 | Page 2 of 18
EV-ADF5901SD2Z Evaluation Board User Guide
UG-864
EVALUATION BOARD HARDWARE
The EV-ADF5901SD2Z evaluation board requires the use of an
EVAL-SDP-CS1Z (SDP-S) controller board to program the
device. The EVAL-SDP-CS1Z is not included and must be
purchased separately. The EV-ADF5901SD2Z schematics are
shown in Figure 7 to Figure 14. The EV-ADF5901SD2Z
evaluation board layout is shown in Figure 15 and Figure 16.
Control VTUNE from the ADF4159. Alternatively, control VTUNE
externally via J7 by removing R20 and powering down the
ADF4159.
OUTPUT SIGNALS
The Tx and LO outputs from the ADF5901 contain dc bias
voltage and are available on the J8 (TXOUT1), J9 (TXOUT2)
and J4 (LOOUT) output SMAs.
POWER SUPPLIES
The EV-ADF5901SD2Z board is powered via a 5 V external
supply that must be connected as described in the Evaluation
Board Quick Start Procedures section.
DEFAULT OPERATION
All the necessary components to operate the ADF5901 are
included on the EV-ADF5901SD2Z.
INPUT SIGNALS
The 100 MHz temperature controlled crystal oscillator (TCXO)
provides the necessary reference signal. An external REFIN can
be used, if desired.
Rev. 0 | Page 3 of 18
UG-864
EV-ADF5901SD2Z Evaluation Board User Guide
EVALUATION BOARD QUICK START PROCEDURES
EV-ADF5901SD2Z CONTROL SOFTWARE
Take the following steps to evaluate the ADF5901:
The control software for the EV-ADF5901SD2Z accompanies
the EV-ADF5901SD2Z on a CD. For software installation
procedures, follow the on-screen instructions.
1. Connect the power supply to the EV-ADF5901SD2Z:
a. 5 V to the Banana Connector P3
b. GND to the Banana Connector P2.
2. Install the ADF5901 software by following the on-screen
To run the EV-ADF5901SD2Z control software, take the
following steps:
instructions.
3. Connect the EVAL-SDP-CS1Z controller board to the PC
and to the EV-ADF5901SD2Z.
4. Install the hardware driver; follow the on-screen instructions.
5. Run the ADF5901 software.
6. Choose ADF5901 and ADF4159 and SDP board (black)
in the Select Device and Connection tab of the software
front panel window (see Figure 2).
7. Ensure that a SDP board connected message appears on
the front panel (see Figure 2).
1. Choose the ADF5901 and ADF4159 file on the desktop or
in the Start menu.
2. Within the Select Device and Connection tab, choose
your device and your connection method, and click
Connect.
3. Confirm that Analog Devices Eval Board connected
displays at the bottom left of the window. Otherwise, the
software has no connection to the EV-ADF5901SD2Z
evaluation board.
8. Connect an ac-coupled signal source analyzer to the TX2
output SMA, J9.
9. Click the ADF5901 Controls tab and click Write All
Note that when connecting the EV-ADF5901SD2Z, it takes
approximately 5 sec to 10 sec for the status label to change.
Registers (see Figure 4).
10. Click the ADF5901 Controls tab and click Initialize
ADF5901 (see Figure 3).
11. Measure the result on TXOUT2 (J9).
Figure 2. Software Front Panel Display—Select Device and Connection
Rev. 0 | Page 4 of 18
EV-ADF5901SD2Z Evaluation Board User Guide
UG-864
To control the ADF5901 settings (see Figure 3), select the
ADF5901 Controls tab.
Use the register section within the ADF5901 Controls tab to
select from the general options available for the ADF5901,
including calibration control and register read back.
To set the calibration frequency for the ADF5901, go to the RF
Settings section shown in Figure 3 under the ADF5901 Controls
tab. Set the frequency to the center of the frequency band. Type
the desired output frequency in the VCO Frequency text box
(in MHz).
At initial power-up of the device, click Initialize ADF5901 to
perform the initialization sequence as described in the ADF5901
data sheet.
Following the sequence, the ADF5901 powers up, and all the
ADF5901 blocks calibrate.
Figure 3. Software Front Panel Display—ADF5901 Controls
Rev. 0 | Page 5 of 18
UG-864
EV-ADF5901SD2Z Evaluation Board User Guide
To control the ADF4159 settings (see Figure 4), select the
ADF4159 Controls tab.
In the PLL Settings area, program the Charge Pump Setting to
the value for which the loop filter was designed. Program the
Phase Detector Polarity to negative when using an inverting
active loop filter configuration. (Note that a passive loop filter
was used on this evaluation board).
Within the ADF4159 Controls tab, select the Main Controls tab
to set the RF Settings and PLL Settings. In the RF Settings
area, set the RF VCO Output Frequency to half the ADF5901
VCO output. In addition, set the Reference Frequency the
same as the applied reference signal. Calculate the PFD
frequency from the reference frequency, the R counter, the
reference doubler, and the reference divide by 2. Ensure that the
value in the PFD Frequency box matches the value specified in
the loop filter design.
Use the Muxout drop-down box within the Main Controls tab
to choose the signal connected to the output of the MUXOUT pin.
Click the button under each register value within the Main
Controls tab to write that value to the device. The register values
are shown in Figure 4 at the bottom of the window. When the
background of a register value is green, this indicates that the
value was changed and needs to be written to the device.
Figure 4. Software Front Panel Display—ADF4159 Controls
Rev. 0 | Page 6 of 18
EV-ADF5901SD2Z Evaluation Board User Guide
UG-864
To configure the ramp functionality of the ADF4159, select the
ADF5901 Tx output with a ramp time of 5 ms. For 200 MHz,
Ramps and Shift Keying tab.
the PLL is programmed for a 100 MHz ramp because the
EV-ADF5901SD2Z uses the ADF5901 auxilary output with a
12 GHz output signal. After each parameter is set in the
software, it must be written to the device.
To select the ramp type, go to the Ramp mode drop-down box
within the Ramps and Shift Keying tab, and set the various
ramp parameters in the CLK1 box and Up Ramp boxes.
To configure the other options in the Ramps and Shift Keying
tab, set the various Ramp and Shift Keying controls of the
ADF4159.
Example
Figure 5 shows the ramping settings for an example of a continuous
triangular ramp of 1000 up ramp steps over 200 MHz at the
Figure 5. Software Front Panel Display—ADF4159 Ramps and Shift Keying
Rev. 0 | Page 7 of 18
UG-864
EV-ADF5901SD2Z Evaluation Board User Guide
EVALUATION AND TESTING
To evaluate and test the performance of the ADF5901, take the
following steps:
4. Select the USB board and the ADF5901 device in the
Select Device and Connection tab of the software front
panel window (see Figure 2).
1. Follow the on-screen instructions to install the ADF5901
evaluation software.
2. Connect the EVAL-SDP-CS1Z controller board to the
EV-ADF5901SD2Z.
1. Connect dc blocked J9 (TXOUT2) to the spectrum
analyzer.
3. Click the ADF5901 icon to run the ADF5901 software.
5. In the ADF4159 Main Controls tab, click Write All Registers
to power up the ADF4159.
6. In the ADF5901 Controls tab, click Initialize ADF5901 to
power up and calibrate the ADF5901. See Figure 6 for the
suggested setup.
7. Measure the TXOUT2 output signal on the J9 SMA.
POWER
+5V
SUPPLY
SDP-S
ADAPTOR
BOARD
SPECTRUM
ANALYZER
PC
BLOCKING CAPACITOR
Figure 6. Typical EV-ADF5901SD2Z Evaluation Board Setup
Rev. 0 | Page 8 of 18
EV-ADF5901SD2Z Evaluation Board User Guide
EVALUATION BOARD SCHEMATICS AND ARTWORK
UG-864
TP21
TP22
I
I
H A _ O C V
H A _ X T
H A
1 0 R
R 9
R 8
0
0
0
I
2 0 P T
D
G A N
0
1
R 3
1 8 P T
TP5
L L P D D D _ V
X T _ D D V A
TP4
L L P D D D _ V
X T _ D D V A
P V
D D D V
D D V A
0
0
0
R 7
R 5
R 4
3
T P
Figure 7. EV-ADF5901SD2Z Schematic (Page 1)
Rev. 0 | Page 9 of 18
UG-864
EV-ADF5901SD2Z Evaluation Board User Guide
J5
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
GPIO0
OUT
OUT
OUT
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
GPIO2
GPIO4
GPIO6
OUT
R35
100K
R36
R6
TBD0603
DNI
100K
J5
120
119
118
117
116
115
114
113
112
111
110
109
108
107
106
105
104
103
102
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
SPI_MOSI
SPI_MISO
SPI_CLK
OUT
OUT
OUT
81
80
79
78
77
76
GPIO1
GPIO3
GPIO5
OUT
OUT
OUT
75
74
73
GPIO7
OUT
72
71
70
69
68
67
66
65
64
63
62
61
Figure 8. EV-ADF5901SD2Z Schematic (Page 2)
Rev. 0 | Page 10 of 18
EV-ADF5901SD2Z Evaluation Board User Guide
UG-864
DNI
R19
TBD0805
R20
0
CPOUT
IN
VTUNE
OUT
AGND
Figure 9. EV-ADF5901SD2Z Schematic (Page 3)
IO
TP36
1
Y1
4
VDD
OUT
GND
2
R43
91
REF
1
3
E/D
OUT
CWX823-100.0MHZ
AGND
AGND
R45
0
REFIN
IN
Figure 10. EV-ADF5901SD2Z Schematic (Page 4)
Rev. 0 | Page 11 of 18
UG-864
EV-ADF5901SD2Z Evaluation Board User Guide
TP32
1
U6
D2
R23
0
R33
0
AVDD_TX
VSUPPLY
A
C
8
7
6
5
1
2
3
4
VOUT
SENSE
GND
OUT
VIN
PG
GND
EN
IN
MBR0540T1G
NC
PAD
PAD
ADP7104
AGND
TP34
U4
5
1
R25
0
1
VIN
EN
R2
AVDD_PLL
R29
0
OUT
3
VOUT
0
NC GND
4
2
ADP150AUJZ-3.3-R7
AGND
TP35
1
U5
5
R26
0
1
3
VIN
EN
DVDD_PLL
R32
0
R30
0
OUT
VOUT
NC GND
4
2
ADP150AUJZ-3.3-R7
AGND
Figure 11. EV-ADF5901SD2Z Schematic (Page 5)
Rev. 0 | Page 12 of 18
EV-ADF5901SD2Z Evaluation Board User Guide
UG-864
TX_AHI
AHI
VCO_AHI
AGND
AGND
AGND
TP29
1
TP30
1
TP31
1
C1
C2
VREG
AGND
AGND
AGND
R22
5.1K
AGND
N D G A
U101
1
AGND
TX_OUT1
24 DOUT
23 LE
22 DATA
21 CLK
20 CE
OUT
IN
IN
IN
IN
IN
IN
IN
2
3
4
5
6
7
8
OUT
TX_AHI
AGND
IO
5901
AGND
TX_OUT2
19 AGND
VREG
18
OUT
AGND
17 AHI
C1
C2
REFIN
IN
1000PF
1000PF
AGND
Figure 12. EV-ADF5901SD2Z Schematic (Page 6)
Rev. 0 | Page 13 of 18
UG-864
EV-ADF5901SD2Z Evaluation Board User Guide
TP14
TP6
TP10
GPIO4
SPI_CLK
CLK_PLL
SPI_CLK
CLK_TX
R55
0
R11
330
R46
330
IN
IN
IN
OUT
OUT
AGND
AGND
TP15
TP7
TP13
GPIO5
R56
0
SPI_MOSI
DATA_PLL
SPI_MOSI
DATA_TX
R12
330
R47
330
IN
IN
IN
OUT
OUT
AGND
AGND
TP8
TP11
GPIO6
LE_PLL
GPIO0
LE_TX
R13
330
R48
330
IN
IN
OUT
OUT
AGND
AGND
AVDD_TX
TP1
IO
GPIO3
TX_DATA
R14
330
IN
OUT
TP12
GPIO2
CE_TX
R49
330
IN
IN
OUT
OUT
AGND
TP9
DVDD_PLL
IO
DOUT_TX
SPI_MISO
R50
0
TP2
GPIO7
CE_PLL
R15
330
IN
OUT
AGND
TP19
MUXOUT_PLL
GPIO1
R24
IN
OUT
0
Figure 13. EV-ADF5901SD2Z Schematic (Page 7)
Rev. 0 | Page 14 of 18
EV-ADF5901SD2Z Evaluation Board User Guide
UG-864
AVDD
DVDD
VP
AGND
AGND
AGND
U2
AGND
R17
23
9
RSET
5.1K
REFIN
C17
C19
21
20
REFIN
CP
SW2
SW1
24
17
OUT
IN
CP
1000PF
1000PF
5
4
RFINA
RFINB
MUXOUT
IN
RFINA
RFINB
OUT
MUXOUT
IN
13
12
CE
IN
IN
CE
AGND
TXDATA
TXDATA
14
15
16
CLK
DATA
LE
IN
IN
IN
CLK
DATA
LE
ADF4159CCPZ
AGND
Figure 14. EV-ADF5901SD2Z Schematic (Page 8)
Rev. 0 | Page 15 of 18
UG-864
EV-ADF5901SD2Z Evaluation Board User Guide
Figure 15. EV-ADF5901SD2Z Layer 1 (Component Side)
Figure 16. EV-ADF5901SD2Z Layer 4 (Bottom Plane)
Rev. 0 | Page 16 of 18
EV-ADF5901SD2Z Evaluation Board User Guide
UG-864
ORDERING INFORMATION
BILL OF MATERIALS
Table 1.
Quantity Reference Designator
Part Description
Manufacturer
AVX
AVX
AVX
AVX
Kemet
Taiyo Yuden
AVX
AVX
Murata
Part Number
4
6
6
6
1
1
1
6
1
1
1
1
1
1
1
1
2
2
3
1
1
1
11
13
C1, C2, C17, C19
C4, C7, C10, C18, C24, C29
C5, C8, C11, C21, C26, C31
C3, C6, C9, C15, C22, C27
C16
C23
C28
C32, C34 to C36, C38, C39
C40
C41
C12
C13
C14
D1
D2
E1
J1, J7
J2, J3
J4, J8, J9
J5
P2
P3
1 nF, 0603 capacitors
1 nF, 0402 capacitors
10 pF, 0402 capacitors
100 nF, 0603 capacitors
47 nF, 0402 capacitor
220 nF, 0402 capacitor
220 nF, 0603 capacitor
1 µF, 0805 capacitors
22 µF, 0805 capacitor
10 pF, 0603 capacitor
220 pF, 0805 capacitor
3.3 nF, 0805 capacitor
100 pF, 0805 capacitor
Diode, standard, 1 A, 50 V
Diode, Schottky, 0.5 A, 20 V
Ferrite bead
CONN-PCB end launch jack
CONN-PCB high frequency SMA
CONN-PCB SMA RA jack
CONN-PCB vertical type RCPT SMD
CONN-PCB single SKT black
CONN-PCB single SKT red
0 Ω, 0402 resistors
06035A102JAT2A
04023C102KAT2A
04023A100JAT2A
06033C104JAT2A
C0402C473K3RACTU
JMK105B7224KV-F
06033C224KAT2A
08053C105KAZ2A
GRM21BE70G226ME51L
06035A100JAT2A
MCCA001042
C0805C332J5GACTU
MCCA001040
1N4001
MBR0520LT1G
7427-92642
142-0701-851
142-0761-801
02K243-40M
FX8-120S-SV(21)
571-0100
571-0500
MC 0.0625W 0402 1% 0R
MC 0.063W 0603 0R
AVX
Multicomp
Kemet
Multicomp
Multicomp
ON Semiconductor
Wuerth Elektronik
Emerson
Emerson (Johnson)
Rosenberger
Hirose
Deltron
Deltron
Multicomp
Multicomp
R1, R2, R23, R25 to R27, R29 to R33
R3 to R5, R7 to R10, R24, R40, R45,
R50, R55, R56
0 Ω, 0603 resistors
9
2
1
5
2
R11 to R15, R46 to R49
R17, R22
R20
R28, R34, R37, R38, R44
R35, R36
330 Ω, 0603 resistors
5.1 kΩ, 0603 resistors
0 Ω, 0805 resistor
390 Ω, 0603 resistors
100 kΩ ,0603 resistor
Multicomp
Multicomp
Multicomp
Multicomp
Multicomp
MC 0.063W 0603 330R
MC 0.063W 0603 5k1
MC 0.1W 0805 0R
MC 0.063W 0603 390R
MC 0.063W 0603 5%
100K
1
1
1
1
1
R41
R43
R18
R19
U2
10 kΩ, 0603 resistor
91 Ω, 0603 resistor
510 Ω, 0805 resistor
1 kΩ, 0805 resistor
ADF4159 13 GHz Fractional-N
frequency synthesizer
Multicomp
Multicomp
Multicomp
Multicomp
MC 0.063W 0603 10K
MC 0.063W 0603 1% 91R
MC 0.1W 0805 1% 510R
MC 0.1W 0805 1% 1K
ADF4159CCPZ
Analog Devices, Inc.
1
2
2
1
1
1
2
1
U3
U4
U5
U6
IC 32 Kbit serial EEPROM
3.0 V CMOS linear regulator
1.8 V CMOS linear regulator
3.3 V CMOS linear regulator
100 MHz crystal clock oscillator
ADF5901 24 GHz TX MMIC
Black test point
Microchip
24LC32A-I/MS
ADP150AUJZ-3.0
ADP150AUJZ-1.8
ADP7104ARDZ-3.3
CWX113-100.0M
ADF5901WCCPZ-U6
20-2137
Analog Devices
Analog Devices
Analog Devices
Connor-Winfield
Analog Devices
Vero
Y1
U101
TP16, TP17
TP23
Red test point
Vero
20-313137
Rev. 0 | Page 17 of 18
UG-864
EV-ADF5901SD2Z Evaluation Board User Guide
Quantity Reference Designator
Part Description
Do not install
Do not install
Do not install
Do not install
Do not install
Manufacturer
Not applicable
Not applicable
Not applicable
Not applicable
Not applicable
Not applicable
Part Number
Not applicable
Not applicable
Not applicable
Not applicable
Not applicable
Not applicable
3
1
C20, C25, C30
C33
2
C37, C42
4
5
R6, R16, R21, R42
R39, R51 to R54
28
TP1 to TP15, TP18 to TP22, TP24, TP29 Do not install
to TP32, TP34 to TP36
4
2
C1, C2, C17, C19
SCREW1, SCREW2
1 nF, 0603 capacitors
Screw, cheese, nylon, M3X10,
PK100
AVX
06035A102JAT2A
119030010
ALLTHREAD Plastics
Limited
2
NUT1, NUT2
Nut/washer, nylon, M3, PK100
DURATOOL
1140030
RELATED LINKS
Resource
ADF5901
ADF4159
ADP7104
Description
Product Page, 24 GHz VCO and PGA with 2-Channel PA Output
Product Page, Direct Modulation/Fast Waveform Generating, 13 GHz, Fractional-N Frequency Synthesizer
Product Page, 20 V, 500 mA, Low Noise, CMOS LDO
ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection
circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions
set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you
have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc.
(“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal,
temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided
for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional
limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term
“Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including
ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may
not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to
promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any
occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board.
Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice
to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO
WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED
TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL
PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF
THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE
AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable
United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of
Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby
submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.
©2015 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
UG13381-0-12/15(0)
Rev. 0 | Page 18 of 18
相关型号：
©2020 ICPDF网 联系我们和版权申明