HMC334LP4 [ADI]
SiGe Wideband Downconverter Mixer SMT, 0.6 - 2.7 GHz;
| 型号： | HMC334LP4 |
| 厂家： | 
ADI |
| 描述： | SiGe Wideband Downconverter Mixer SMT, 0.6 - 2.7 GHz 射频 微波 |
| 文件： | 总8页 (文件大小：785K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
HMC334LP4 / 334LP4E
v03.0410
SiGe WIDEBAND
DOWNCONVERTER, 0.6 - 2.7 GHz
Typical Applications
Features
The HM334LP4(E) is ideal for:
• Basestations & Repeaters
• GSM, GPRS & Edge
Conversion Loss: 0 dB
9
LO to RF Isolation: 48 dB
Single-Ended LO Drive: -6 to +6 dBm
Input IP3: +26 dBm
• CDMA, W-CDMA & TD-SCDMA
• WiMAX & LTE
SSB Noise Figure: 11 dB
On-Chip RF Balun
24 Lead 4x4mm QPackage: m
Functional Diagram
General Descriptin
The HC334LP4(E) is
a low noise, wideband
downnvertRFIC which is ideal for Cellular/3G
and WiM/4G apications from 0.6 to 2.7 GHz.
The LO inpcpts drive levels from -6 to +6 dBm
while the RFIC provides 48 dB of LO to RF isolation,
nd 0 dB onversion loss. The HMC334LP4(E) will
suoran IF output bandwidth of up to 600 MHz
and onsumes only 173 mA from a +5V supply.
This wideband active mixer also provides excellent
performance in the presence of high level “Blocker”
signals, making it ideal for receiver applications in
demanding environments.
Electrical atio
TA = +25 °Bm*, VSLO = VSIF = +5V, IF = 240 MHz
Parameter
Frequency Rang
Frequency Range, LO
Frequency Range, IF
Min.
Typ.
0.6 - 2.7
0.35 - 3.0
1 - 600
-1
Max.
Units
GHz
GHz
MHz
dB
Conversion Gain (IF XFMR Included)
SSB Noise Figure
-5
11
dB
LO to RF Isolation
30
48
dB
IF Output Impedance (Diff)
IP3 (Input)
200
Ohms
dBm
dBm
dBm
mA
+26
1 dB Compression (Input)
LO Drive Input Level
8.5
12
-6 to +6
173
Supply Current
225
*Unless otherwise noted all measurements with R1 = 13 Ohms and single-ended 50 Ohm IF output with Port J2 or J3 shorted to ground.
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price, delivery, and to place orders: Analog Devices, Inc.,
responsibilityisassumedbyAnalog Devices foritsuse,norforanyinfringements of patents orother
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 781-329-4700 • Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
9 - 38
Application Support: Phone: 1-800-ANALOG-D
Trademarks and registered trademarks are thepropertyoftheir respectiveowners.
HMC334LP4 / 334LP4E
v03.0410
SiGe WIDEBAND
DOWNCONVERTER, 0.6 - 2.7 GHz
Conversion Gain vs.
Conversion Gain vs. Temperature
LO Drive, IF = 100 MHz [1]
@ LO = 0 dBm, IF = 100 MHz [1]
10
10
9
5
0
5
0
-5
-5
-3 dBm
0 dBm
+3 dBm
C
-10
-15
-20
-10
85 C
-40 C
-15
-20
0.6
1
1.4
1.8
2.2
2.6
3
3
3
0.6
1
1.4
.8
2.2
2.6
3
3
3
RF FREQUENCY (GHz)
RF FREQCY (GHz)
Conversion Gain vs.
Conven Gain vs. Temperature
LO Drive, IF = 240 MHz [1]
@ LO = 0 BmIF = 240 MHz [1]
10
10
5
0
5
0
-5
-5
-3 dBm
-10
-15
-20
-10
0 dBm
+25 C
+85 C
-40 C
+3 dBm
-15
-20
0.6
1
1.4
.2
2
0.6
1
1.4
1.8
2.2
2.6
RF F
RF FREQUENCY (GHz)
P1dB vs. Teure
P1dB vs. Temperature
@ LO = 0 00 MHz [1]
@ LO = 0 dBm, IF = 240 MHz [1]
25
25
20
15
10
20
15
10
5
5
+25C
+25C
+85C
+85C
-40C
-40C
0
0
-5
-5
-10
-10
0.6
1
1.4
1.8
2.2
2.6
0.6
1
1.4
1.8
2.2
2.6
RF FREQUENCY (GHz)
RF FREQUENCY (GHz)
[1] LO < RF
* Unless otherwise noted all measurements with R1= 13 Ohms
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price, delivery, and to place orders: Analog Devices, Inc.,
responsibilityisassumedbyAnalog Devices foritsuse,norforanyinfringements of patents orother
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 781-329-4700 • Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are thepropertyoftheir respectiveowners.
9 - 39
Application Support: Phone: 1-800-ANALOG-D
HMC334LP4 / 334LP4E
v03.0410
SiGe WIDEBAND
DOWNCONVERTER, 0.6 - 2.7 GHz
Input IP3 vs. Temperature
Input IP3 vs. LO Drive, IF = 100 MHz [1]
@ LO = 0 dBm, IF = 100 MHz [1]
40
35
30
25
20
40
9
35
30
25
20
15
10
5
15
-3 dBm
0 dBm
+3 dBm
C
85C
-40C
10
5
0
0
0.6
1
1.4
1.8
2.2
2.6
3
0.6
1
1.4
.8
2.2
2.6
3
3
3
RF FREQUENCY (GHz)
RF FREQCY (GHz)
Input Ivs. Temperature
Input IP3 vs. LO Drive, IF = 240 MHz [1]
@ LO = 0 BmIF = 240 MHz [1]
40
40
35
30
25
20
35
25
20
15
15
-3 dBm
+25C
0 dBm
+85C
+3 dBm
-40C
10
10
5
5
0
0
0.6
1
1.4
.2
2
3
0.6
1
1.4
1.8
2.2
2.6
RF F
RF FREQUENCY (GHz)
Noise Fig
RF Return Loss @ LO = 0 dBm [1]
25
10
+25 C
+85 C
-40 C
RF
LO
20
15
10
5
0
-10
-20
-30
-40
0
0.6
1
1.4
1.8
2.2
2.6
3
0
0.5
1
1.5
2
2.5
RF FREQUENCY (GHz)
RF FREQUENCY (GHz)
[1] LO < RF
* Unless otherwise noted all measurements with R1= 13 Ohms
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price, delivery, and to place orders: Analog Devices, Inc.,
responsibilityisassumedbyAnalog Devices foritsuse,norforanyinfringements of patents orother
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 781-329-4700 • Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are thepropertyoftheir respectiveowners.
9 - 40
Application Support: Phone: 1-800-ANALOG-D
HMC334LP4 / 334LP4E
v03.0410
SiGe WIDEBAND
DOWNCONVERTER, 0.6 - 2.7 GHz
Isolation @ LO = 0 dBm, IF = 100 MHz [1]
LO - RF Isolation @ LO = 0 dBm [1]
60
60
9
50
40
30
20
50
40
30
F = 100
2Hz
20
10
LO TO IF
RF TO IF
10
0
0.6
0
1
1.4
1.8
2.2
2.6
3
3
3
0.6
1
1.4
.8
2.2
2.6
3
3
3
RF FREQUENCY (GHz)
RF FREQCY (GHz)
Conversion Gain vs.
Temperature, IF = 184 MHz, USB [2]
Noise Figre, = 184 MHz, USB [2]
25
10
+25 C
+85 C
-40 C
5
0
0
15
10
5
-5
+25 C
-10
+85
-4
-15
0
-20
0.6
1
1.4
1.8
2.2
2.6
0.6
1
1.4
.2
2.
RF FREQUENCY (GHz)
RF
Input IP3 vs
Input IP3 vs. Temperature
LO Drive, z, USB [2]
@ LO = 0 dBm, IF = 184 MHz, USB [2]
40
40
35
30
25
20
35
30
25
20
15
15
+25C
-3 dBm
+85C
0 dBm
-40C
+3 dBm
10
10
5
0
5
0
0.6
1
1.4
1.8
2.2
2.6
0.6
1
1.4
1.8
2.2
2.6
RF FREQUENCY (GHz)
RF FREQUENCY (GHz)
[1] LO < RF
[2] LO > RF
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price, delivery, and to place orders: Analog Devices, Inc.,
responsibilityisassumedbyAnalog Devices foritsuse,norforanyinfringements of patents orother
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 781-329-4700 • Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are thepropertyoftheir respectiveowners.
9 - 41
Application Support: Phone: 1-800-ANALOG-D
HMC334LP4 / 334LP4E
v03.0410
SiGe WIDEBAND
DOWNCONVERTER, 0.6 - 2.7 GHz
Typical Supply
Current vs. Supply Voltage
Absolute Maximum Ratings
RF Input (VSLO = VSIF= +5V)
LO Drive (VSLO = VSIF= +5V)
VccLO, VccIF
+21 dBm
VSLO = VSIF (V)
ISLO + ISIF (mA)
9
+12 dBm
+6 Vdc
150 °C
+4.5
146
173
200
+5.0
Channel Temperature
+5.5
Continuous Pdiss (T = 85°C)
(derate 27.8 mW/°C above 85°C)
Downconverter will operate over full age range shown above.
1.8 W
Thermal Resistance
(channel to ground paddle)
36 °C/W
ELECTRSTATIC NSITE DEVICE
OBSEHANDLINRECAUTIONS
Storage Temperature
Operating Temperature
-65 to 150 °C
-40 to 85 °C
Outline Drawing
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS]
3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE.
4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM.
PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM.
5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
6. ALL GROUND LEADS AND GROUND PADDLE MUST BE
SOLDERED TO PCB RF GROUND.
7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED
LAND PATTERN.
Package Information
Part Number
Package Body Material
Lead Finish
MSL Rating
MSL1 [1]
Package Marking [3]
H334
XXXX
HMC334LP4
Low Stress Injection Molded Plastic
Sn/Pb Solder
H334
XXXX
MSL1 [2]
HMC334LP4E
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
[1] Max peak reflow temperature of 235 °C
[2] Max peak reflow temperature of 260 °C
[3] 4-Digit lot number XXXX
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price, delivery, and to place orders: Analog Devices, Inc.,
responsibilityisassumedbyAnalog Devices foritsuse,norforanyinfringements of patents orother
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 781-329-4700 • Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are thepropertyoftheir respectiveowners.
9 - 42
Application Support: Phone: 1-800-ANALOG-D
HMC334LP4 / 334LP4E
v03.0410
SiGe WIDEBAND
DOWNCONVERTER, 0.6 - 2.7 GHz
Pin Descriptions
Pin Number
Function
Description
Supply for LO Amplifier.
Interface Schematic
9
Draws approximately 120mA from VSLO.
A 13 Ohm resistor (R1) must be connected
externally between the VSLO supply and the
VccLO pin. See evaluation PCB schematic.
1
VccLO
2, 5, 8, 11,
14, 17, 20, 23
These pins and the ground paddle should be
connected to a high quality RF/DC ground.
GND
LOP
LO Input Port. This pin needs a DC blocking capacitor.
(Typical voltage on this pin will be 1.5 - 1.8V)
3
For single ended applications, this pin should be AC
grounded
4
LON
The pins are not connwever, all data
shown hereimeasupins connected to
RF/DC grounally.
6, 7, 12,
21, 22, 24
N/C
ential baseband puts, 200 ohm differential output
dance. Et should draw approximately 25mA
thout LO power and 28mA from VSIF with LO
power on.
9, 10
IFN, IF
nded 50 Ohm operation, port J2 or J3 should be
sto RF/DC ground. See evaluation PCB schematic.
Center tap of the RF transformer. Biased at 2.2V when con-
nected to ground through two 91 ohm resistors.
13, 18
CTRF
Pin to be connected to a high quality RF/DC ground. Also
can be used to drive the RF port differentially if needed.
15
16
GNDRF
RF
50 Ohms impedance can be matched
from 600 - 3000 MHz.
Supply decoupling for the mixer stage.
(Typical voltage on this pin will be 4.8V)
Connect C3 to a high quality RF/DC
ground per evaluation PCB schematic.
19
VccIF
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price, delivery, and to place orders: Analog Devices, Inc.,
responsibilityisassumedbyAnalog Devices foritsuse,norforanyinfringements of patents orother
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 781-329-4700 • Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are thepropertyoftheir respectiveowners.
9 - 43
Application Support: Phone: 1-800-ANALOG-D
HMC334LP4 / 334LP4E
v03.0410
SiGe WIDEBAND
DOWNCONVERTER, 0.6 - 2.7 GHz
Evaluation PCB
9
List of Materials fon PCB 117528 [1]
The circuit board used in the final application
should use RF circuit design techniques. Signal
lines should have 50 Ohm impedance while the
package ground leads and exposed paddle should
be connected directly to the ground plane similar
to that shown. A sufficient number of via holes
should be used to connect the top and bottom
ground planes. The evaluation circuit board shown
is available from Hittite upon request.
Item
J1 - J4
J5 - J6
C1 - C3
C4
Description
MA Co
tor, 0402 Pkg.
or, 0402 Pkg.
1pacitor, 0402 Pkg.
10 KpF Capacitor, 0402 Pkg.
1.3 pF Capacitor, 0402 Pkg.
0.1 μF Capacitor, 0805 Pkg.
2.7 nH Chip Inductor, 0603 Pkg.
2 nH Chip Inductor, 0603 Pkg.
13 Ohm Resistor, 1206 Pkg.
91 Ohm Resistor, 0805 Pkg.
M/A-Com 4:1 Balun, MABAES0061
HMC334LP4 / HMC334LP4E
117527 Evaluation Board
C5
C6
C7
C8, C9
L1
L2
R1
R2, R3
T1
U1
[2]
PCB
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Rogers 4350
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price, delivery, and to place orders: Analog Devices, Inc.,
responsibilityisassumedbyAnalog Devices foritsuse,norforanyinfringements of patents orother
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 781-329-4700 • Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are thepropertyoftheir respectiveowners.
9 - 44
Application Support: Phone: 1-800-ANALOG-D
HMC334LP4 / 334LP4E
v03.0410
SiGe WIDEBAND
DOWNCONVERTER, 0.6 - 2.7 GHz
Evaluation PCB Schematic
9
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
For price, delivery, and to place orders: Analog Devices, Inc.,
responsibilityisassumedbyAnalog Devices foritsuse,norforanyinfringements of patents orother
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
rights of third parties that may result from its use. Specifications subject to change without notice. No
Phone: 781-329-4700 • Order online at www.analog.com
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are thepropertyoftheir respectiveowners.
9 - 45
Application Support: Phone: 1-800-ANALOG-D
相关型号：
HMC336MS8GETR
SPDT, 0MHz Min, 6000MHz Max, 2dB Insertion Loss-Max, ROHS COMPLIANT, PLASTIC, SMT, MSOP-8
HITTITE
©2020 ICPDF网 联系我们和版权申明