LT3029EDE#TR [ADI]
Adjustable Positive LDO Regulator, 2 Output, 1.215V1 Min, 1.215V2 Min, 19.5V1 Max, 19.5V2 Max, PDSO16;型号: | LT3029EDE#TR |
厂家: | ADI |
描述: | Adjustable Positive LDO Regulator, 2 Output, 1.215V1 Min, 1.215V2 Min, 19.5V1 Max, 19.5V2 Max, PDSO16 光电二极管 输出元件 电源电路 线性稳压器IC 调节器 |
文件: | 总20页 (文件大小:1620K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LT3029
Dual 500mA/500mA
Low Dropout, Low Noise,
Micropower Linear Regulator
DescripTion
FeaTures
The LT®3029 is a dual, micropower, low noise, low drop-
out linear regulator. The device operates either with a
common input supply or independent input supplies for
each channel, over an input voltage range of 1.8V to 20V.
Each output supplies up to 500mA of output current with
a typical dropout voltage of 300mV. Quiescent current is
well controlled in dropout. With an external 10nF bypass
n
Output Current: 500mA per Channel
n
Low Dropout Voltage: 300mV
n
Low Noise: 20µV
(10Hz to 100kHz)
RMS
n
n
Low Quiescent Current: 55µA per Channel
Wide Input Voltage Range: 1.8V to 20V (Common or
Independent Input Supply)
n
n
Adjustable Output: 1.215V Reference Voltage
Very Low Quiescent Current in Shutdown: <1µA per
Channel
Stable with 3.3µF Minimum Output Capacitor
Stable with Ceramic, Tantalum or Aluminum
Electrolytic Capacitors
Reverse-Battery and Reverse Output-to-Input
Protection
Current Limit with Foldback and Thermal Shutdown
Tracking/Sequencing Capability: Compatible with
LTC292X Power Supply Tracking ICs
Thermally Enhanced 16-Lead MSOP and 16-Lead
(4mm × 3mm) DFN Packages
capacitor, output noise is only 20µV
over a 10Hz to
RMS
100kHz bandwidth. Designed for use in battery-powered
systems, the low 55µA quiescent current per channel
makes it an ideal choice. In shutdown, quiescent current
drops to less than 1µA. Shutdown control is independent
foreachchannel,allowingforflexiblepowermanagement.
n
n
n
TheLT3029optimizesstabilityandtransientresponsewith
low ESR ceramic output capacitors, requiring a minimum
of only 3.3µF. The regulator does not require the addition
of ESR, as is common with other regulators.
n
n
n
Internal circuitry provides reverse-battery protection,
reverse-current protection, current limiting with foldback
and thermal shutdown. The device is available as an
adjustable output voltage device with a 1.215V reference
voltage. The LT3029 is offered in the thermally enhanced
16-lead MSOP and 16-lead, low profile (4mm × 3mm ×
0.75mm) DFN packages.
applicaTions
n
n
n
n
n
General Purpose Linear Regulator
Battery-Powered Systems
Microprocessor Core/Logic Supplies
Post Regulator for Switching Supplies
Tracking/Sequencing Power Supplies
L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks and
ThinSOT is a trademark of Linear Technology Corporation. All other trademarks are the property
of their respective owners.
Dropout Voltage vs Load Current
Typical applicaTion
400
T
= 25°C
2.5VIN to 1.5V/1.8V Application
J
350
300
250
200
150
100
50
V
IN
2.5V
V
OUT1
IN1
OUT1
LT3029
1.8V
10nF
500mA
113k
1%
3.3µF
3.3µF
3.3µF
BYP1
ADJ1
IN2
237k
1%
SHDN1
V
OUT2
1.5V
SHDN2 OUT2
500mA
10nF
54.9k
1%
BYP2
ADJ2
0
237k
1%
GND
0
50 100 150 200 250 300 350 400 450 500
OUTPUT CURRENT (mA)
3029 TA01b
3029 TA01
3029fb
1
For more information www.linear.com/LT3029
LT3029
absoluTe MaxiMuM raTings (Note 1)
IN1, IN2 Pin Voltage................................................ 22V
OUT1, OUT2 Pin Voltage......................................... 22V
Input-to-Output Differential Voltage........................ 22V
ADJ1, ADJ2 Pin Voltage............................................ 9V
BYP1, BYP2 Pin Voltage ........................................ 0.6V
SHDN1 , SHDN2 Pin Voltage.................................. 22V
Output Short-Circuit Duration .......................... Indefinite
Operating Junction Temperature (Notes 2, 12)
LT3029E............................................. –40°C to 125°C
LT3029I.............................................. –40°C to 125°C
LT3029H ............................................ –40°C to 150°C
LT3029MP.......................................... –55°C to 125°C
Storage Temperature Range................... –65°C to 150°C
Lead Temperature (Soldering, 10 sec)
(MSOP Only)..................................................... 300°C
pin conFiguraTion
TOP VIEW
TOP VIEW
BYP1
NC
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
ADJ1
SHDN1
IN1
1
2
3
4
5
6
7
8
BYP1
NC
OUT1
OUT1
GND
OUT2
OUT2
BYP2
16 ADJ1
15 SHDN1
14 IN1
OUT1
OUT1
GND
IN1
17
17
GND
13 IN1
12 IN2
GND
IN2
11 IN2
OUT2
OUT2
BYP2
IN2
10 SHDN2
9
ADJ2
SHDN2
ADJ2
MSE PACKAGE
16-LEAD PLASTIC MSOP
DE PACKAGE
T
= 125°C (LT3029E/LT3029I/LT3029MP), θ = 37°C/W, θ : 5°C/W TO 10°C/W
JA JC
JMAX
16-LEAD (4mm × 3mm) PLASTIC DFN
T
= 150°C (LT3029H), θ = 37°C/W, θ : 5°C/W TO 10°C/W
JA JC
JMAX
T
= 125°C (LT3029E/LT3029I), θ = 38°C/W , θ = 4.3°C/W
JA JC
JMAX
EXPOSED PAD (PIN 17) IS GND, MUST BE SOLDERED TO PCB GND
T
JMAX
= 150°C (LT3029H), θ = 38°C/W , θ = 4.3°C/W
JA JC
EXPOSED PAD (PIN 17) IS GND, MUST BE SOLDERED TO PCB GND
orDer inForMaTion
LEAD FREE FINISH
LT3029EDE#PBF
LT3029IDE#PBF
LT3029HDE#PBF
LT3029EMSE#PBF
LT3029IMSE#PBF
LT3029HMSE#PBF
LT3029MPMSE#PBF
LEAD BASED FINISH
LT3029EDE
TAPE AND REEL
PART MARKING*
3029
PACKAGE DESCRIPTION
TEMPERATURE RANGE
–40°C to 125°C
–40°C to 125°C
–40°C to 150°C
–40°C to 125°C
–40°C to 125°C
–40°C to 150°C
–55°C to 125°C
TEMPERATURE RANGE
–40°C to 125°C
–40°C to 125°C
–40°C to 150°C
–40°C to 125°C
–40°C to 125°C
–40°C to 150°C
–55°C to 125°C
LT3029EDE#TRPBF
LT3029IDE#TRPBF
LT3029HDE#TRPBF
LT3029EMSE#TRPBF
LT3029IMSE#TRPBF
LT3029HMSE#TRPBF
LT3029MPMSE#TRPBF
TAPE AND REEL
16-Lead (4mm × 3mm) Plastic DFN
16-Lead (4mm × 3mm) Plastic DFN
16-Lead (4mm × 3mm) Plastic DFN
16-Lead Plastic MSOP
3029
3029
3029
3029
16-Lead Plastic MSOP
3029
16-Lead Plastic MSOP
3029
16-Lead Plastic MSOP
PART MARKING*
3029
PACKAGE DESCRIPTION
LT3029EDE#TR
16-Lead (4mm × 3mm) Plastic DFN
16-Lead (4mm × 3mm) Plastic DFN
16-Lead (4mm × 3mm) Plastic DFN
16-Lead Plastic MSOP
LT3029IDE
LT3029IDE#TR
3029
LT3029HDE
LT3029HDE#TR
3029
LT3029EMSE
LT3029EMSE#TR
LT3029IMSE#TR
3029
LT3029IMSE
3029
16-Lead Plastic MSOP
LT3029HMSE
LT3029HMSE#TR
LT3029MPMSE#TR
3029
16-Lead Plastic MSOP
LT3029MPMSE
3029
16-Lead Plastic MSOP
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
3029fb
2
For more information www.linear.com/LT3029
LT3029
elecTrical characTerisTics The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. (Note 2)
PARAMETER
CONDITIONS
= 500mA
MIN
TYP
MAX
UNITS
l
Minimum Input Voltage (Notes 3, 11)
ADJ1, ADJ2 Pin Voltage (Notes 3, 4, 9)
I
1.8
2.3
V
LOAD
V
= 2V, I
= 1mA
LOAD
1.203
1.191
1.173
1.215
1.215
1.215
1.227
1.239
1.239
V
V
V
IN
l
l
2.3V < V < 20V, 1mA < I
< 500mA (E, I, MP)
< 500mA (H)
IN
LOAD
LOAD
2.3V < V < 20V, 1mA < I
IN
l
Line Regulation (Note 3)
Load Regulation (Note 3)
∆V = 2V to 20V, I
= 1mA
LOAD
0.5
2.5
5
mV
IN
V
IN
V
IN
V
IN
= 2.3V, ∆I
= 2.3V, ∆I
= 2.3V, ∆I
= 1mA to 500mA
= 1mA to 500mA (E, I, MP)
= 1mA to 500mA (H)
6
15
32
mV
mV
mV
LOAD
LOAD
LOAD
l
l
Dropout Voltage
I
I
= 10mA
= 10mA
0.11
0.16
0.2
0.18
0.25
V
V
LOAD
LOAD
l
l
l
l
V
= V
OUT(NOMINAL)
IN
(Notes 5, 6, 11)
I
I
= 50mA
= 50mA
0.22
0.31
V
V
LOAD
LOAD
I
I
= 100mA
= 100mA
0.25
0.34
V
V
LOAD
LOAD
I
I
= 500mA
= 500mA
0.3
0.36
0.46
V
V
LOAD
LOAD
l
l
l
l
l
l
GND Pin Current (per Channel)
I
I
I
I
I
I
= 0mA
55
90
1.1
2
4.3
10
150
250
2
µA
µA
mA
mA
mA
mA
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
V
= V
= 1mA
IN
OUT(NOMINAL)
(Notes 5, 7)
= 50mA
= 100mA
= 250mA
= 500mA
3.5
8
16
Output Voltage Noise
C
= 10µF, C
= 10nF, I
= 500mA,
20
µV
RMS
OUT
BYP
LOAD
BW = 10Hz to 100kHz
ADJ1/ADJ2 Pin Bias Current
Shutdown Threshold
ADJ1, ADJ2 (Notes 3, 8)
30
100
1.1
nA
l
l
V
V
= Off to On
= On to Off
0.45
0.40
V
V
OUT
OUT
0.20
l
l
SHDN1/SHDN2 Pin Current (Note 10)
V
V
, V
= 0V
= 20V
0
0.6
0.5
3
µA
µA
SHDN1 SHDN2
, V
SHDN1 SHDN2
Quiescent Current in Shutdown (per Channel)
Ripple Rejection
V
= 6V, V
= 0V, V = 0V
SHDN2
0.01
67
0.1
µA
dB
IN
SHDN1
V
f
= 2.715V (Avg), V
= 0.5V ,
P-P
55
IN
RIPPLE
= 120Hz, I
= 500mA
RIPPLE
LOAD
Current Limit (Note 9)
V
V
= 7V, V
= 0V
OUT
1.5
A
IN
IN
l
l
= 2.3V, ∆V
= –0.1V
520
mA
OUT
Input Reverse Leakage Current
Reverse Output Current
V
V
= –20V, V
= 0V
1
mA
µA
IN
OUT
= 1.215V, V = 0V
0.5
10
OUT
IN
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 3: The LT3029 is tested and specified for these conditions with the
ADJ1/ADJ2 pin connected to the corresponding OUT1/OUT2 pin.
Note 4: Maximum junction temperature limits operating conditions. The
regulated output voltage specification does not apply for all possible
combinations of input voltage and output current. When operating at
maximum input voltage, limit the output current range. When operating at
maximum output current, limit the input voltage range.
Note 2: The LT3029 is tested and specified under pulse load conditions
such that T ≈ T . The LT3029E is 100% tested at T = 25°C. Performance
J
A
A
of the LT3029E over the full –40°C to 125°C operating junction
temperature range is assured by design, characterization and correlation
with statistical process controls. The LT3029I is guaranteed over the full
–40°C to 125°C operating junction temperature range. The LT3029MP is
100% tested and guaranteed over the –55°C to 125°C operating junction
temperature range. The LT3029H is tested at 150°C operating junction
temperature. High junction temperatures degrade operating lifetimes.
Operating lifetime is derated at junction temperatures greater than 125°C.
Note 5: To satisfy minimum input voltage requirements, the LT3029 is
tested and specified for these conditions with an external resistor divider
(two 243k resistors) for an output voltage of 2.437V. The external resistor
divider adds 5µA of DC load on the output.
Note 6: Dropout voltage is the minimum input to output voltage differential
needed to maintain regulation at a specified output current. In dropout, the
output voltage equals: V – V
.
IN
DROPOUT
3029fb
3
For more information www.linear.com/LT3029
LT3029
elecTrical characTerisTics
Note 7: GND pin current is tested with V = 2.437V and a current source
Note 10: SHDN1/SHDN2 pin current flows into the pin.
IN
load. This means the device is tested while operating in its dropout region
or at the minimum input voltage specification. This is the worst-case
GND pin current. The GND pin current decreases slightly at higher input
voltages. Total GND pin current equals the sum of output 1 and output 2
GND pin currents.
Note 8: ADJ1/ADJ2 pin bias current flows into the pin.
Note 9: The LT3029 contains current limit foldback circuitry. See the
Note 11: The LT3029 minimum input voltage specification limits dropout
voltage under some output voltage/load conditions. See the curve of
Minimum Input Voltage in the Typical Performance Characteristics.
Note 12: The LT3029 includes overtemperature protection that is intended
to protect the device during momentary overload conditions. Junction
temperature exceeds the maximum operating junction temperature when
overtemperature protection is active. Continuous operation above the
specified maximum operating junction temperature may impair device
reliability.
Typical Performance Characteristics for current limit as a function of the
V
– V
differential voltage.
IN
OUT
Typical perForMance characTerisTics TJ = 25°C, unless otherwise noted.
Typical Dropout Voltage
Guaranteed Dropout Voltage
500
450
400
350
300
250
200
150
100
50
500
450
400
350
300
250
200
150
100
50
= TEST POINTS
T = 150°C
J
T = 150°C
J
T = 125°C
J
T = 25°C
J
T = 25°C
J
T = –55°C
J
0
0
200
250 300 350 400 450 500
0
50 100 150
200
250 300 350 400 450 500
0
50 100 150
OUTPUT CURRENT (mA)
OUTPUT CURRENT (mA)
3029 G02
3029 G01
Dropout Voltage vs Temperature
Quiescent Current (per Channel)
500
450
400
350
300
250
200
150
100
50
150
125
100
75
V
= 6V
= 243k, I = 5µA
L
IN
L
R
I
= 500mA
L
I
= 250mA
= 100mA
L
I
L
V
= V
IN
SHDN
I
= 10mA
L
50
25
I
= 50mA
L
I
= 1mA
L
0
0
25
–75 –50 –25
0
50 75 100 125 150 175
25
–75 –50 –25
0
50 75 100 125 150 175
TEMPERATURE (°C)
TEMPERATURE (°C)
3029 G03
3029 G04
3029fb
4
For more information www.linear.com/LT3029
LT3029
TJ = 25°C, unless otherwise noted.
Typical perForMance characTerisTics
ADJ1 or ADJ2 Pin Voltage
Quiescent Current (per Channel)
1.239
1.233
1.227
1.221
1.215
1.209
1.203
1.197
1.191
160
140
120
100
80
I
= 1mA
T = 25°C
J
L
R
OUT
= 243k
L
V
= 1.215V
V
= V
IN
SHDN
60
40
20
V
= 0V
SHDN
0
25
–75 –50 –25
0
50 75 100 125 150 175
8
0
2
4
6
10 12 14 16 18 20
TEMPERATURE (°C)
INPUT VOLTAGE (V)
3029 G05
3029 G06
GND Pin Current (per Channel)
GND Pin Current (per Channel)
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
16
14
12
10
8
T = 25°C
J
T = 25°C
J
FOR V
= 1.215V
FOR V
= 1.215V
OUT
OUT
R
= 24.3Ω, I = 50mA
L
L
R
R
= 2.43Ω, I = 500mA
L
L
6
= 4.05Ω, I = 300mA
L
L
4
R
R
= 121.5Ω, I = 10mA
L
L
R
= 12.15Ω, I = 100mA
L
L
2
= 1.215kΩ, I = 1mA
L
L
0
4
0
1
2
3
5
6
7
8
9
10
4
0
1
2
3
5
6
7
8
9
10
INPUT VOLTAGE (V)
INPUT VOLTAGE (V)
3029 G07
3029 G08
SHDN1 or SHDN2 Pin Threshold
(On-to-Off)
GND Pin Current vs ILOAD
16
14
12
10
8
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
T = 25°C
J
IN
I
= 1mA
L
V
= V
+ 1V
OUT(NOMINAL)
6
4
2
0
200
250 300 350 400 450 500
0
50 100 150
25
–75 –50 –25
0
50 75 100 125 150 175
OUTPUT CURRENT (mA)
TEMPERATURE (°C)
3029 G09
3029 G10
3029fb
5
For more information www.linear.com/LT3029
LT3029
TJ = 25°C, unless otherwise noted.
Typical perForMance characTerisTics
SHDN1 or SHDN2 Pin Threshold
(Off-to-On)
SHDN1 or SHDN2 Pin
Input Current
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
T = 25°C
J
I
= 500mA
L
I
= 1mA
L
25
0
2
4
6
8
12 14 16 18 20
–75 –50 –25
0
50 75 100 125 150 175
10
TEMPERATURE (°C)
SHDN PIN VOLTAGE (V)
3029 G11
3029 G12
SHDN1 or SHDN2 Pin
Input Current
ADJ1 or ADJ2 Pin Bias Current
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
150
135
120
105
90
V
= 20V
SHDN
75
60
45
30
15
0
25
–75 –50 –25
0
50 75 100 125 150 175
25
–75 –50 –25
0
50 75 100 125 150 175
TEMPERATURE (°C)
TEMPERATURE (°C)
3029 G14
3029 G13
Current Limit
Current Limit
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
V
= 0V
V
V
= 7V
OUT
IN
OUT
= 0V
T = 25°C
J
T = –55°C
J
T = 125°C
J
T = 150°C
J
25
8
–75 –50 –25
0
50 75 100 125 150 175
0
2
4
6
10 12 14 16 18 20
INPUT VOLTAGE (V)
TEMPERATURE (°C)
3029 G15
3029 G16
3029fb
6
For more information www.linear.com/LT3029
LT3029
TJ = 25°C, unless otherwise noted.
Typical perForMance characTerisTics
Reverse Current
Input Ripple Rejection
100
90
300
270
240
210
180
150
120
90
T = 25°C
J
L
V
V
= 0V
ADJ
IN
I
= 500mA
OUT(NOMINAL)
= 0
= V
= 1.215V
OUT
V
C
= V
+1V + 50mV
RIPPLE
IN
BYP
RMS
80
C
= 10µF
OUT
70
I
ADJ
60
50
40
30
20
10
0
C
= 3.3µF
1M
OUT
60
30
I
OUT
0
10
100
1k
10k 100k
10M
25
–75 –50 –25
0
50 75 100 125 150 175
FREQUENCY (Hz)
TEMPERATURE (°C)
3029 G18
I
I
FLOWS INTO ADJ PIN TO GND PIN
FLOWS INTO OUT PIN TO IN PIN
ADJ
OUT
3029 G17
Input Ripple Rejection
Input Ripple Rejection
100
90
100
90
80
70
60
50
40
30
20
10
0
V
IN
= V + 1.5V + 0.5V RIPPLE
OUT(NOMINAL) P-P
f = 120Hz
C
= 0.01µF
I
L
= 500mA
BYP
80
70
60
50
C
= 1000pF
BYP
40
30
20
10
0
C
= 100pF
BYP
T = 25°C
J
L
I
= 500mA
= V
V
C
+1V + 50mV
RIPPLE
RMS
IN
OUT
OUT(NOMINAL)
= 10µF
10
100
1k
10k 100k
1M
10M
25
–75 –50 –25
0
50 75 100 125 150 175
FREQUENCY (Hz)
TEMPERATURE (°C)
3029 G19
3029 G20
Channel-to-Channel Isolation
Minimum Input Voltage
100
90
2.50
2.25
2.00
1.75
1.50
1.25
1.00
0.75
0.50
0.25
0
T
= 25°C
J
V
= 1.215V
OUT
80
I
= 500mA
L
70
60
50
I
= 1mA
L
40
30
20
10
0
10
100
1k
10k 100k
1M
10M
25
–75 –50 –25
0
50 75 100 125 150 175
FREQUENCY (Hz)
TEMPERATURE (°C)
GIVEN CHANNEL IS TESTED WITH 50mV
SIGNAL ON OPPOSING CHANNEL, BOTH
CHANNELS DELIVERING FULL CURRENT
3029 G21
RMS
3029 G22
3029fb
7
For more information www.linear.com/LT3029
LT3029
TJ = 25°C, unless otherwise noted.
Typical perForMance characTerisTics
Channel-to-Channel Isolation
Load Regulation
0
–2
V
OUT1
–4
50mV/DIV
–6
–8
V
OUT2
–10
–12
–14
–16
–18
–20
50mV/DIV
3029 G23
50µs/DIV
C
C
C
= 10µF
= 10µF
BYP2
∆I = 50mA TO 500mA
∆I = 1mA TO 500mA
L
OUT1
OUT2
BYP1
L1
L2
= 6V, V
∆I = 50mA TO 500mA
25
–75 –50 –25
0
50 75 100 125 150 175
= C
= 0.01µF
V
IN
= V
= 5V
OUT1
OUT2
TEMPERATURE (°C)
3029 G24
Output Noise Spectral Density
Output Noise Spectral Density
10
1
10
1
T = 25°C
T = 25°C
J
J
OUT
L
C
I
= 10µF
C
C
I
= 10µF
= 0
OUT
BYP
L
= 500mA
= 500mA
V
OUT
= 5V
V
= 5V
OUT
C
= 1000pF
BYP
V
= V
ADJ
OUT
C
=
BYP
V
=V
OUT
ADJ
100pF
0.1
0.01
0.1
C
= 0.01µF
BYP
0.01
0.01
0.1
1
10
100
0.01
0.1
1
10
100
FREQUENCY (kHz)
FREQUENCY (kHz)
3029 G26
3029 G25
RMS Output Noise
vs Load Current
RMS Output Noise
vs Bypass Capacitor
160
140
120
100
80
160
140
120
100
80
T
= 25°C
T
= 25°C
OUT
= 500mA
J
J
C
= 10µF
C
I
= 10µF
OUT
C
C
V
= 5V
OUT
= 0
BYP
BYP
L
BW
= 10nF
f
= 10Hz TO 100kHz
V
= 5V
OUT
V
= 1.215V
OUT
V
=V
ADJ
OUT
60
60
40
40
V
= 5V
OUT
20
20
V
=V
ADJ
OUT
0
0.01
0
0.1
1
10
100
10
100
1000
10000
LOAD CURRENT (mA)
C
(pF)
BYP
3029 G28
3029 G27
3029fb
8
For more information www.linear.com/LT3029
LT3029
TJ = 25°C, unless otherwise noted.
Typical perForMance characTerisTics
10Hz to 100kHz Output Noise,
CBYP = 0pF
10Hz to 100kHz Output Noise,
CBYP = 100pF
V
V
OUT
100µV/DIV
OUT
100µV/DIV
3029 G29
3029 G30
1ms/DIV
1ms/DIV
C
L
V
= 10µF
C
= 10µF
OUT
OUT
I = 500mA
I = 500mA
L
= 5V
V
= 5V
OUT
OUT
10Hz to 100kHz Output Noise,
10Hz to 100kHz Output Noise,
CBYP = 0.01µF
C
BYP = 1000pF
V
V
OUT
OUT
100µV/DIV
100µV/DIV
3029 G31
3029 G32
1ms/DIV
1ms/DIV
C
L
V
= 10µF
C
L
V
= 10µF
OUT
OUT
I = 500mA
I = 500mA
= 5V
= 5V
OUT
OUT
3029fb
9
For more information www.linear.com/LT3029
LT3029
TJ = 25°C, unless otherwise noted.
Transient Response, CBYP = 0.01µF
Typical perForMance characTerisTics
Transient Response, CBYP = 0pF
V
DEVIATION
OUT
V
DEVIATION
OUT
200mV/DIV
250mA/DIV
50mV/DIV
LOAD CURRENT DEVIATION
LOAD CURRENT DEVIATION
250mA/DIV
3029 G33
3029 G34
200µs/DIV
I = 100mA
20µs/DIV
I = 100mA
V
C
C
= 6V
V
C
C
= 6V
IN
IN
L
IN
IN
L
= 10µF
T = 25°C
= 10µF
T = 25°C
J
J
= 10µF
V
= 5V
= 10µF
V
= 5V
OUT
OUT
OUT
OUT
Start-Up Time from Shutdown,
Start-Up Time from Shutdown,
C
BYP = 0pF
C
BYP = 0.01µF
V
V
OUT
OUT
1V/DIV
1V/DIV
SHDN
VOLTAGE
2V/DIV
SHDN
VOLTAGE
2V/DIV
3029 G35
3029 G36
1ms/DIV
I = 500mA
L
= 1.5V
OUT
1ms/DIV
I = 500mA
V
= 2.5V
OUT
V
= 2.5V
OUT
IN
IN
L
C
= 10µF
V
C
= 10µF
V
= 1.5V
OUT
R = 3Ω
R = 3Ω
L
L
3029fb
10
For more information www.linear.com/LT3029
LT3029
pin FuncTions
BYP1/BYP2 (Pin 1/Pin 8): Bypass. Use the BYP1/BYP2
pins to bypass the reference of the LT3029 regulator and
achieve low output noise performance. Internal circuitry
as a battery’s output impedance rises with frequency. A
bypass capacitor in the range of 1µF to 10µF suffices. The
LT3029’sdesignwithstandsreversevoltagesontheINpins
with respect to ground and the OUT pins. In the case of
a reversed input, which occurs if a battery is plugged in
backwards, the LT3029 acts as if a diode is in series with
its input. No reverse current flows into the LT3029 and no
reverse voltage appears at the load. The device protects
itself and the load.
clamps the BYP1/BYP2 pins to 0.6V (one V ) from
BE
ground.Asmallcapacitorfromthecorrespondingoutputto
thispinbypassesthereferencetolowertheoutputvoltage
noise. Using a maximum value of 10nF reduces the output
voltage noise to a typical 20µV
bandwidth. If not used, this pin must be left unconnected.
over a 10Hz to 100kHz
RMS
NC (Pin 2): No Connect. This pin is not connected to
SHDN1/SHDN2 (Pin 15/Pin 10): Shutdown. Pulling the
SHDN1 or SHDN2 pin low puts its corresponding LT3029
channelintoalowpowerstateandturnsitsoutputoff. The
SHDN1 and SHDN2 pins are completely independent of
each other, and each SHDN pin only affects operation on
its corresponding channel. Drive the SHDN1 and SHDN2
pinswitheitherlogicoranopencollector/drainwithpull-up
resistors. The resistors supply the pull-up current to the
open collectors/drains and the SHDN1 or SHDN2 current,
typically less than 1µA. If unused, connect the SHDN1 and
SHDN2 to their corresponding IN pins. Each channel will
be in its low power shutdown state if its corresponding
SHDN pin is not connected.
any internal circuitry. It may be floated, tied to V or tied
IN
to GND.
OUT1/OUT2 (Pins 3, 4/Pins 6, 7): Output. The outputs
supply power to the loads. A minimum 3.3µF output ca-
pacitor prevents oscillations on each output. Applications
with large output load transients require larger values of
output capacitance to limit peak voltage transients. See
the Applications Information section for more on output
capacitance and reverse output characteristics.
GND (Pin 5, 17): Ground. The exposed pad (Pin 17) of
the DFN and MSOP packages is an electrical connection
to GND. To ensure proper electrical and thermal perfor-
mance, solder Pin 17 to the PCB ground and tie directly
to Pin 5. Connect the bottom of the output voltage setting
resistor divider directly to GND (Pin 5) for optimum load
regulation performance.
ADJ1/ADJ2: (Pin 16/Pin 9) Adjust Pin. These are the error
amplifier inputs. These pins are internally clamped to 9V.
A typical input bias current of 30nA flows into the pins
(see curve of ADJ1/ADJ2 Pin Bias Current vs Temperature
in the Typical Performance Characteristics section). The
ADJ1andADJ2pinvoltageis1.215Vreferencedtoground
and the output voltage range is 1.215V to 19.5V.
IN1/IN2 (Pins 13, 14/Pins 11, 12): Inputs. The IN1/IN2
pins supply power to each channel. The LT3029 requires
a bypass capacitor at the IN1/IN2 pins if located more
than six inches away from the main input filter capacitor.
Include a bypass capacitor in battery-powered circuits,
3029fb
11
For more information www.linear.com/LT3029
LT3029
applicaTions inForMaTion
TheLT3029isadual500mA/500mAlowdropoutregulator
with independent inputs, micropower quiescent current
andshutdown.Thedevicesuppliesupto500mAfromeach
channel’s output at a typical dropout voltage of 300mV.
The two regulators share a common GND pin and are
thermally coupled. However, the two inputs and outputsof
the LT3029 operate independently. Each channel can be
shut down independently, but a thermal shutdown fault
on either channel shuts off the output on both channels.
The addition of a 10nF reference bypass capacitor lowers
LT3029
OUT1/OUT2
V
OUT
V
IN1/IN2
IN
R2
R1
R2
C
VOUT = 1.215V 1+
+ I
(
R2
ADJ
(
)
)
VADJ = 1.215V
ADJ1/ADJ2
GND
IADJ = 30nA AT 25°C
OUTPUT RANGE = 1.215V TO 19.5V
R1
3029 F01
Figure 1. Adjustable Operation
LinearTechnologytestsandspecifieseachLT3029channel
with its ADJ pin tied to the corresponding OUT pin for a
1.215V output voltage. Specifications for output voltages
greaterthan1.215Vareproportionaltotheratioofdesired
output voltage to 1.215V:
output voltage noise to 20µV
over a 10Hz to 100kHz
RMS
bandwidth. Additionally, the reference bypass capacitor
improves transient response of the regulator, lowering
the settling time for transient load conditions. The low
operating quiescent current (55µA per channel) drops to
less than 1µA in shutdown. In addition to the low quies-
cent current, the LT3029 regulator incorporates several
protection features that make it ideal for use in battery-
powered systems. Most importantly, the device protects
itself against reverse input voltages. Current limiting with
foldback necessitates a minimum load current of 20µA
for input/output voltage differentials of more than 10V to
keep the output regulated.
VOUT
1.215V
Forexample, loadregulationoneitheroutputforanoutput
current change of 1mA to 500mA is typically –2.5mV at
V
= 1.215V. At V
= 2.5V, load regulation is:
OUT
OUT
2.5V
1.215V
• (−2.5mV) = − 5.14mV
Adjustable Operation
Table 1 shows 1% resistor divider values for some com-
mon output voltages with a resistor divider current of
approximately 5µA.
EachoftheLT3029’schannelshasanoutputvoltagerange
of 1.215V to 19.5V. Figure 1 illustrates that output voltage
is set by the ratio of two external resistors. The device
regulates the output to maintain the corresponding ADJ
pin voltage at 1.215V referenced to ground. R1’s current
equals 1.215V/R1. R2’s current equals R1’s current plus
theADJpinbiascurrent. TheADJpinbiascurrent, 30nAat
25°C, flows through R2 into the ADJ pin. Use the formula
in Figure 1 to calculate output voltage. Linear Technol-
ogy recommends that the value of R1 be less than 243k
to minimize errors in the output voltage due to the ADJ
pin bias current. In shutdown, the output turns off and
the divider current is zero. Curves of ADJ Pin Voltage vs
Temperature and ADJ Pin Bias Current vs Temperature
appearintheTypicalPerformanceCharacteristicssection.
Table 1. Output Voltage Resistor Divider Values
V
R1
(k)
R2
(k)
OUT
(V)
1.5
1.8
2.5
3
237
237
243
232
210
200
54.9
113
255
340
357
619
3.3
5
3029fb
12
For more information www.linear.com/LT3029
LT3029
applicaTions inForMaTion
Bypass Capacitance and Low Noise Performance
2 and 3. When used with a 5V regulator, a 16V 10µF Y5V
capacitor can exhibit an effective value as low as 1µF to
2µF for the applied DC bias voltage and over the operat-
ing temperature range. X5R and X7R dielectrics result in
more stable characteristics and are more suitable for use
as the output capacitor. The X7R type has better stability
across temperature, while the X5R is less expensive and
is available in higher values.
Using a bypass capacitor connected between a channel’s
BYP pin and its corresponding OUT pin significantly low-
ers LT3029 output voltage noise, but is not required in
all applications. Linear Technology recommends a good
quality low leakage capacitor. This capacitor bypasses the
regulator’sreference,providingalowfrequencynoisepole.
A 10nF bypass capacitor introduces a noise pole that de-
creases output voltage noise to as low as 20µV
. Using
RMS
abypasscapacitorprovidestheaddedbenefitofimproving
transient response. With no bypass capacitor, and a 10µF
output capacitor, a 100mA to 500mA load step settles to
within 1% of its final value in approximately 100µs. With
the addition of a 10nF bypass capacitor and evaluating
the same load step, output voltage excursion stays within
1% (see Transient Response in the Typical Performance
Characteristics section). Using a bypass capacitor makes
regulator start-up time proportional to the value of the
bypass capacitor. For example, a 10nF bypass capacitor
and 10µF output capacitor slow start-up time to 7ms.
20
BOTH CAPACITORS ARE 16V,
1210 CASE SIZE, 10µF
0
X5R
–20
–40
–60
Y5V
–80
–100
0
8
12 14
2
4
6
10
16
DC BIAS VOLTAGE (V)
3029 F02
Figure 2. Ceramic Capacitor DC Bias Characteristics
Output Capacitance and Transient Response
The LT3029 design is stable with a wide range of output
capacitors. The ESR of the output capacitor affects stabil-
ity, most notably with small capacitors. Linear Technology
recommends a minimum output capacitor of 3.3µF with
an ESR of 3Ω, or less, to prevent oscillations. The LT3029
is a micropower device, and output transient response is
a function of output capacitance. Larger values of output
capacitance decrease the peak deviations and provide im-
provedtransientresponseforlargerloadcurrentchanges.
40
20
X5R
0
–20
–40
Y5V
–60
–80
BOTH CAPACITORS ARE 16V,
1210 CASE SIZE, 10µF
Ceramic capacitors require extra consideration. Manufac-
turersmakeceramiccapacitorswithavarietyofdielectrics,
each with different behavior across temperature and
applied voltage. The most common dielectrics specify
the EIA temperature characteristic codes of Z5U, Y5V,
X5R and X7R. Z5U and Y5V dielectrics provide high C-V
products in a small package at low cost, but exhibit strong
voltage and temperature coefficients, as shown in Figures
–100
–50 –25
0
25
50
TEMPERATURE (°C)
75
100 125
3029 F03
Figure 3. Ceramic Capacitor Temperature Characteristics
3029fb
13
For more information www.linear.com/LT3029
LT3029
applicaTions inForMaTion
Exercise care even when using X5R and X7R capacitors;
theX5RandX7Rcodesonlyspecifyoperatingtemperature
rangeandmaximumcapacitancechangeovertemperature.
Capacitance change due to DC bias (voltage coefficient)
with X5R and X7R capacitors is better than with Y5V and
Z5U capacitors, but can still be significant enough to drop
capacitor values below appropriate levels. Capacitor DC
biascharacteristicstendtoimproveascasesizeincreases.
LinearTechnologyrecommendsverifyingexpectedversus
actual capacitance values at operating voltage in situ for
an application.
Thermal Considerations
TheLT3029’spowerhandlingcapabilitylimitsthemaximum
rated junction temperature (125°C, LT3029E/LT3029I/
LT3029MPor150°C,LT3029H).Twocomponentscomprise
the power dissipated by each channel:
1. Output current multiplied by the input/output voltage
differential: (I )(V – V ), and
OUT
IN
OUT
2. GND pin current multiplied by the input voltage: (I
)
GND
(V ).
IN
Ground pin current is found by examining the GND Pin
Current curves in the Typical Performance Characteristics
section.
Voltage and temperature coefficients are not the only
sources of problems. Some ceramic capacitors have a
piezoelectric response. A piezoelectric device generates
voltage across its terminals due to mechanical stress,
similar to the way a piezoelectric accelerometer or micro-
phone works. For a ceramic capacitor, the stress can be
induced by vibrations in the system or thermal transients.
The resulting voltages produced can cause appreciable
amounts of noise, especially when a ceramic capacitor is
used for noise bypassing. A ceramic capacitor produced
Figure 4’s trace in response to light tapping from a pencil.
Similar vibration induced behavior can masquerade as
increased output voltage noise.
Power dissipation for each channel equals the sum of the
two components listed above. Total power dissipation for
the LT3029 equals the sum of the power dissipated by
each channel.
TheLT3029’sinternalthermalshutdowncircuitryprotects
bothchannelsofthedeviceifeitherchannelexperiences
an overload or fault condition. Activation of the thermal
shutdowncircuitryturnsbothchannelsoff.Iftheoverload
or fault condition is removed, both outputs are allowed
to turn back on. For continuous normal conditions, do
not exceed the maximum junction temperature rating of
(125°C,LT3029E/LT3029I/LT3029MPor150°C,LT3029H).
Carefully consider all sources of thermal resistance from
junction-to-ambient, including additional heat sources
mounted in proximity to the LT3029. For surface mount
devices,usetheheatspreadingcapabilitiesofthePCboard
and its copper traces to accomplish heat sinking. Copper
board stiffeners and plated through-holes can also spread
the heat generated by power devices.
C
C
LOAD
= 10µF
= 0.01µF
= 500mA
OUT
BYP
I
V
OUT
500µV/DIV
3029 F04
100ms/DIV
The following tables list thermal resistance as a function
of copper area in a fixed board size. All measurements
were taken in still air on a four-layer FR-4 board with 1oz
solid internal planes, and 2oz external trace planes with a
total board thickness of 1.6mm. For further information
onthermalresistanceandusingthermalinformation,refer
to JEDEC standard JESD51, notably JESD51-12.
Figure 4. Noise Resulting from Tapping on a Ceramic Capacitor
3029fb
14
For more information www.linear.com/LT3029
LT3029
applicaTions inForMaTion
Thethermalresistanceisintherangeof35°C/Wto40°C/W,
dependingonthecopperarea.So,thejunctiontemperature
rise above ambient temperature approximately equals:
Table 2. DE Package, 16-Lead DFN
COPPER AREA
THERMAL RESISTANCE
TOPSIDE*
BACKSIDE BOARD AREA
(JUNCTION-TO-AMBIENT)
2
2
2
2
2
2
2
2
2
2500mm
2500mm
2500mm
2500mm
2500mm
2500mm
2500mm
2500mm
2500mm
36°C/W
37°C/W
38°C/W
40°C/W
(0.37W + 0.52W) 39°C/W = 34.7°C
2
1000mm
The maximum junction temperature then equals the maxi-
mum ambient temperature plus the maximum junction
temperature rise above ambient temperature, or:
2
225mm
2
100mm
*Device is mounted on topside.
T
JMAX
= 50°C + 34.7°C = 84.7°C
Table 3. MSE Package, 16-Lead MSOP
COPPER AREA
Protection Features
THERMAL RESISTANCE
TOPSIDE*
BACKSIDE BOARD AREA
(JUNCTION-TO-AMBIENT)
The LT3029 regulator incorporates several protection fea-
tures that make it ideal for use in battery-powered circuits.
In addition to the normal protection features associated
with monolithic regulators, such as current limiting and
thermal limiting, the device protects itself against reverse
input voltages and reverse voltages from output to input.
The two regulators have independent inputs, a common
GND pin and are thermally coupled. However, the two
channels of the LT3029 operate independently. Each
channel’s output can be shut down independently, and
a fault condition on one output does not affect the other
output electrically, unless the thermal shutdown circuitry
is activated.
2
2
2
2
2
2
2
2
2
2500mm
2500mm
2500mm
2500mm
2500mm
2500mm
2500mm
2500mm
2500mm
35°C/W
36°C/W
37°C/W
39°C/W
2
1000mm
2
225mm
2
100mm
*Device is mounted on topside.
The junction-to-case thermal resistance (θ ), measured
JC
at the Exposed Pad on the back of the die, is 4.3°C/W for
the DFN package, and 5°C/W to 10°C/W for the MSOP
package.
Calculating Junction Temperature
Example: Channel 1’s output voltage is set to 1.8V. Chan-
nel 2’s output voltage is set to 1.5V. Each channel’s input
voltage is 2.5V. Each channel’s output current range is
0mA to 500mA. The application has a maximum ambient
temperature of 50°C. What is the LT3029’s maximum
junction temperature?
Current limit protection and thermal overload protection
protect the device against current overload conditions at
each output of the LT3029. For normal operation, do not
allowthejunctiontemperaturetoexceed125°C(LT3029E/
LT3029I/LT3029MP) or 150°C (LT3029H). The typical
thermal shutdown temperature threshold is 165°C and
thecircuitryincorporatesapproximately5°Cofhysteresis.
The power dissipated by each channel equals:
I
(V – V ) + I (V )
OUT GND IN
OUT(MAX) IN
Each channel’s input withstands reverse voltages of 22V.
Current flow into the device is limited to less than 1mA
(typicallylessthan100µA)andnonegativevoltageappears
at the respective channel’s output. The device protects
both itself and the load against batteries that are plugged
in backwards.
where for each output:
= 500mA
I
OUT(MAX)
V = 2.5V
IN
I
at (I
= 500mA, V = 2.5V) = 8.5mA
OUT IN
GND
The LT3029 incurs no damage if either channel’s output
is pulled below ground. If the input is left open-circuit, or
grounded, the output can be pulled below ground by 22V.
The output acts like an open circuit, and no current flows
from the output. However, current flows in (but is limited
So, for output 1:
P = 500mA (2.5V – 1.8V) + 8.5mA (2.5V) = 0.37W
For output 2:
P = 500mA (2.5V – 1.5V) + 8.5mA (2.5V) = 0.52W
by)theexternalresistordividerthatsetstheoutputvoltage.
3029fb
15
For more information www.linear.com/LT3029
LT3029
applicaTions inForMaTion
The LT3029 incurs no damage if either ADJ pin is pulled
aboveorbelowgroundby9V. Iftheinputisleftopencircuit
or grounded, the ADJ pins perform like an open circuit
down to –1.5V, and then like a 1.2k resistor down to –9V
whenpulledbelowground.Whenpulledaboveground,the
ADJ pins perform like an open circuit up to 0.5V, then like
a 5.7k resistor up to 3V, then like a 1.8k resistor up to 9V.
If either of the LT3029’s IN pins is forced below its cor-
responding OUT pin, or the OUT pin is pulled above its
corresponding IN pin, input current for that channel typi-
cally drops to less than 2µA. This occurs if the IN pin is
connectedtoadischarged(lowvoltage)battery,andeither
a backup battery or a second regulator circuit holds up
the output. The state of that channel’s SHDN pin has no
effect on the reverse output current if the output is pulled
above the input.
In situations where an ADJ pin connects to a resistor
divider that would pull the pin above its 9V clamp volt-
age if the output is pulled high, the ADJ pin input current
must be limited to less than 5mA. For example, assume
a resistor divider sets the regulated output voltage to
1.5V, and the output is forced to 20V. The top resistor of
the resistor divider must be chosen to limit the current
into the ADJ pin to less than 5mA when the ADJ pin is
at 9V. The 11V difference between the OUT and ADJ pins
divided by the 5mA maximum current into the ADJ pin
yields a minimum top resistor value of 2.2k.
Overload Recovery
Like many IC power regulators, the LT3029 has safe
operating area (SOA) protection. The safe area protec-
tion decreases current limit as input-to-output voltage
increases and keeps the power transistor inside a safe
operating region for all values of input-to-output voltage.
The protective design provides some output current at
all values of input-to-output voltage up to the specified
maximum operational input voltage of 20V.
In circuits where a backup battery is required, several
different input/output conditions can occur. The output
voltage may be held up while the input is either pulled
to ground, pulled to some intermediate voltage or is left
open-circuit. Current flow back into the output follows the
curve shown in Figure 5.
When power is first applied, as input voltage rises, the
output follows the input, allowing the regulator to start-up
intoveryheavyloads. Duringstart-up, astheinputvoltage
is rising, the input-to-output voltage differential is small,
allowing the regulator to supply large output currents.
With a high input voltage, an event can occur wherein
removal of an output short will not allow the output to
recover. The event occurs with a heavy output load when
the input voltage is high and the output voltage is low.
Common situations occur immediately after the removal
of a short-circuit or if the shutdown pin is pulled high after
the input voltage has already been turned on. The load line
intersects the output current curve at two points creating
two stable output operating points for the regulator. With
this double intersection, the input power supply may need
to be cycled down to zero and brought up again to make
the output recover.
5.0
T = 25°C
J
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
V
V
= 0V
= V
IN
ADJ
OUT
I
I
ADJ
OUT
4
0
1
2
3
5
6
7
8
9
OUTPUT VOLTAGE (V)
I
I
FLOWS INTO ADJ PIN TO GND PIN
FLOWS INTO OUT PIN TO IN PIN
ADJ
OUT
3029 F05
Figure 5. Reverse Output Current
3029fb
16
For more information www.linear.com/LT3029
LT3029
package DescripTion
Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings.
DE Package
16-Lead Plastic DFN (4mm × 3mm)
(Reference LTC DWG # 05-08-1732 Rev Ø)
0.70 0.05
3.30 0.05
1.70 0.05
3.60 0.05
2.20 0.05
PACKAGE
OUTLINE
0.25 0.05
0.45 BSC
3.15 REF
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED
R = 0.115
TYP
0.40 0.10
16
4.00 0.10
(2 SIDES)
9
R = 0.05
TYP
3.30 0.10
3.00 0.10
(2 SIDES)
1.70 0.10
PIN 1 NOTCH
R = 0.20 OR
PIN 1
TOP MARK
(SEE NOTE 6)
0.35 × 45°
CHAMFER
(DE16) DFN 0806 REV Ø
8
1
0.23 0.05
0.45 BSC
0.75 0.05
0.200 REF
3.15 REF
0.00 – 0.05
BOTTOM VIEW—EXPOSED PAD
NOTE:
1. DRAWING PROPOSED TO BE MADE VARIATION OF VERSION (WGED-3) IN JEDEC
PACKAGE OUTLINE MO-229
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE
TOP AND BOTTOM OF PACKAGE
3029fb
17
For more information www.linear.com/LT3029
LT3029
package DescripTion
Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings.
MSE Package
16-Lead Plastic MSOP, Exposed Die Pad
(Reference LTC DWG # 05-08-1667 Rev F)
BOTTOM VIEW OF
EXPOSED PAD OPTION
2.845 ±0.102
(.112 ±.004)
2.845 ±0.102
(.112 ±.004)
0.889 ±0.127
(.035 ±.005)
1
8
0.35
REF
5.10
(.201)
MIN
1.651 ±0.102
(.065 ±.004)
1.651 ±0.102
(.065 ±.004)
3.20 – 3.45
(.126 – .136)
0.12 REF
DETAIL “B”
CORNER TAIL IS PART OF
THE LEADFRAME FEATURE.
FOR REFERENCE ONLY
DETAIL “B”
16
9
0.305 ±0.038
0.50
(.0197)
BSC
NO MEASUREMENT PURPOSE
4.039 ±0.102
(.159 ±.004)
(NOTE 3)
(.0120 ±.0015)
TYP
0.280 ±0.076
(.011 ±.003)
RECOMMENDED SOLDER PAD LAYOUT
16151413121110
9
REF
DETAIL “A”
0.254
(.010)
3.00 ±0.102
(.118 ±.004)
(NOTE 4)
0° – 6° TYP
4.90 ±0.152
(.193 ±.006)
GAUGE PLANE
0.53 ±0.152
(.021 ±.006)
1 2 3 4 5 6 7 8
DETAIL “A”
0.86
(.034)
REF
1.10
(.043)
MAX
0.18
(.007)
SEATING
PLANE
0.17 – 0.27
(.007 – .011)
TYP
0.1016 ±0.0508
(.004 ±.002)
MSOP (MSE16) 0213 REV F
0.50
(.0197)
BSC
NOTE:
1. DIMENSIONS IN MILLIMETER/(INCH)
2. DRAWING NOT TO SCALE
3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS.
MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS.
INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX
6. EXPOSED PAD DIMENSION DOES INCLUDE MOLD FLASH. MOLD FLASH ON E-PAD SHALL
NOT EXCEED 0.254mm (.010") PER SIDE.
3029fb
18
For more information www.linear.com/LT3029
LT3029
revision hisTory
REV
DATE
3/11
4/14
DESCRIPTION
PAGE NUMBER
A
Added Overload Recovery section to Applications Information
Added H-grade to the DFN package
16
2
B
3029fb
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representa-
tion that the interconnection of its circuits as described herein will not infringe on existing patent rights.
19
LT3029
Typical applicaTion
Coincident Tracking Supply Application
3.3V
V
C
OUT1
GATE
0.1µF
3.3V
OUT1
V
GATE
CC
1.8V
0.1µF
IN1
3.3µF
10nF 113k
1%
500mA
3.3µF
3.3µF
OFF
ON
RAMP
LTC2923
ON
BYP1
ADJ1
LT3029
SHDN1
V
V
OUT1
OUT2
1M
237k
1%
500mV/DIV
RAMPBUF
TRACK1
TRACK2
FB1
SDO
FB2
113k
1%
2.5V
IN2
OUT2
V
OUT2
54.9k
10nF
90.9k
1%
3.3µF 1.5V
54.9k
1%
1%
500mA
BYP2
ADJ2
SHDN2
3029 TA02b
10ms/DIV
63.4k
1%
237k
1%
GND
GND
3029 TA02
relaTeD parTs
PART NUMBER DESCRIPTION
COMMENTS
LT1761
100mA, Low Noise Micropower LDO
V : 1.8V to 20V, V
= 1.22V, V = 0.3V, I = 20µA, I < 1µA,
OUT(MIN) DO Q SD
IN
Low Noise < 20µV
, Stable with 1µF Ceramic Capacitors, ThinSOTTM Package
RMS
LT1763
500mA, Low Noise Micropower LDO
V : 1.8V to 20V, V
= 1.22V, V = 0.3V, I = 30µA, I < 1µA,
DO Q SD
IN
OUT(MIN)
Low Noise < 20µV
, S8 and DFN Packages
RMS
LT1963/
LT1963A
1.5A, Low Noise, Fast Transient
Response LDOs
V : 2.1V to 20V, V
= 1.21V, V = 0.34V, I = 1mA, I < 1µA,
OUT(MIN) DO Q SD
RMS
IN
Low Noise: < 40µV
, “A” Version Stable with Ceramic Capacitors;
DD, TO220-5, SOT223, S8 and TSSOP Packages
LT1964
LT1965
200mA, Low Noise Micropower,
Negative LDO
V : –1.9V to –20V, V
= –1.22V, V = 0.34V, I = 30µA, I = 3µA,
OUT(MIN) DO Q SD
IN
Low Noise: <30µV
, Stable with Ceramic Capacitors, ThinSOT Package
RMS
1.1A, Low Noise LDO
V : 1.8V to 20V, V
= 1.20V, V = 0.31V, I = 0.5mA, I < 1µA,
OUT(MIN) DO Q SD
IN
Low Noise: <40µV
, Stable with Ceramic Capacitors; 3mm × 3mm DFN,
RMS
MS8E, DD-Pak and TO-220 Packages
LT3020
LT3021
LT3023
LT3024
LTC3025
LTC3026
LT3027
LT3028
100mA, Low Voltage VLDO
500mA, Low Voltage VLDO
V : 0.9V to 10V, V = 0.20V, V = 0.15V, I = 120µA, I < 3µA;
IN
OUT(MIN)
DO
Q
SD
3mm × 3mm DFN and MS8 Packages
V : 0.9V to 10V, V = 0.20V, V = 0.16V, I = 120µA, I < 3µA;
IN
OUT(MIN)
DO
Q
SD
5mm × 5mm DFN and SO8 Packages
Dual 100mA, Low Noise,
Micropower LDO
V : 1.8V to 20V, V = 1.22V, V = 0.30V, I = 40µA, I < 1µA;
IN
OUT(MIN)
DO
Q
SD
DFN and MS10E Packages
Dual 100mA/500mA, Low Noise,
Micropower LDO
V : 1.8V to 20V, V
= 1.22V, V = 0.30V, I = 60µA, I < 1µA;
IN
OUT(MIN)
DO
Q
SD
DFN and TSSOP-16E Packages
300mA, Low Voltage Micropower VLDO
V : 0.9V to 5.5V, Low I : 54µA, Low Noise < 80µV
, 45mV Dropout Voltage;
RMS
IN
Q
2mm × 2mm 6-Lead DFN Package
V : 1.14V to 5.5V, Low I : 950µA, Low Noise < 110µV , 100mV Dropout Voltage;
RMS
1.5A, Low Input Voltage VLDO
IN
Q
10-Lead 3mm × 3mm DFN and MS10E Packages
Dual 100mA, Low Noise, Micropower
LDO with Independent Inputs
V : 1.8V to 20V, V = 1.22V, V = 0.30V, I = 50µA, I < 1µA;
IN
OUT(MIN)
DO
Q
SD
DFN and MS10E Packages
Dual 100mA/500mA, Low Noise, Micropower V : 1.8V to 20V, V
LDO with Independent Inputs
= 1.22V, V = 0.32V, I = 60µA, I < 1µA;
IN
OUT(MIN)
DO
Q
SD
DFN and TSSOP-16E Packages
LT3080/
LT3080-1
1.1A, Parallelable, Low Noise LDO
V : 1.2V to 36V, V : 0V to 35.7V, Low Noise < 40µV
, 300mV Dropout Voltage
IN
OUT
RMS
(2-Supply Operation), Current-Based Reference with 1-Resistor V
Set, Directly
OUT
Parallelable (No Op Amp Required), Stable with Ceramic Capacitors;
TO-220, SOT-223, MS8E and 3mm × 3mm DFN Packages
3029fb
LT 0414 REV B • PRINTED IN USA
20 LinearTechnology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
●
●
(408)432-1900 FAX: (408) 434-0507 www.linear.com/LT3029
LINEAR TECHNOLOGY CORPORATION 2010
相关型号:
LT3029EDE#TRPBF
LT3029 - Dual 500mA/500mA Low Dropout, Low Noise, Micropower Linear Regulator; Package: DFN; Pins: 16; Temperature Range: -40°C to 85°C
Linear
LT3029EMSE#PBF
LT3029 - Dual 500mA/500mA Low Dropout, Low Noise, Micropower Linear Regulator; Package: MSOP; Pins: 16; Temperature Range: -40°C to 85°C
Linear
LT3029EMSE#TRPBF
LT3029 - Dual 500mA/500mA Low Dropout, Low Noise, Micropower Linear Regulator; Package: MSOP; Pins: 16; Temperature Range: -40°C to 85°C
Linear
LT3029HDE
Adjustable Positive LDO Regulator, 2 Output, 1.215V1 Min, 1.215V2 Min, 19.5V1 Max, 19.5V2 Max, PDSO16
ADI
©2020 ICPDF网 联系我们和版权申明