OP181GS [ADI]
Ultralow Power, Rail-to-Rail Output Operational Amplifiers; 超低功耗,轨到轨输出运算放大器型号: | OP181GS |
厂家: | ADI |
描述: | Ultralow Power, Rail-to-Rail Output Operational Amplifiers |
文件: | 总16页 (文件大小:450K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Ultralow Power, Rail-to-Rail Output
Operational Amplifiers
a
OP181/OP281/OP481
FEATURES
PIN CONFIGURATIONS
Low Supply Current: 4 A/Amplifier max
Single-Supply Operation: 2.7 V to 12 V
Wide Input Voltage Range
Rail-to-Rail Output Swing
Low Offset Voltage: 1.5 mV
No Phase Reversal
8-Lead SO
(S Suffix)
8-Lead Epoxy DIP
(P Suffix)
NC
1
8
NULL
–IN A
+IN A
V–
NULL
–IN A
+IN A
V–
1
2
3
4
8
7
6
5
NC
V+
OP181
V+
OUT A
NULL
OP181
4
5
OUT A
NULL
APPLICATIONS
NC = NO CONNECT
Comparator
Battery Powered Instrumentation
Safety Monitoring
Remote Sensors
Low Voltage Strain Gage Amplifiers
NC = NO CONNECT
8-Lead SO
(S Suffix)
8-Lead Epoxy DIP
(P Suffix)
1
8
V+
OUT A
–IN A
+IN A
V–
OUT A
–IN A
+IN A
V–
1
2
3
4
8
7
6
5
V+
OP281
OUT B
–IN B
+IN B
OP281
OUT B
–IN B
+IN B
4
5
GENERAL DESCRIPTION
8-Lead TSSOP
(RU Suffix)
The OP181, OP281 and OP481 are single, dual and quad
ultralow power, single-supply amplifiers featuring rail-to-rail
outputs. All operate from supplies as low as 2.0 V and are
specified at +3 V and +5 V single supply as well as ±5 V dual
supplies.
1
8
OP281
4
5
Fabricated on Analog Devices’ CBCMOS process, the OP181
family features a precision bipolar input and an output that
swings to within millivolts of the supplies and continues to sink
or source current all the way to the supplies.
14-Lead Epoxy DIP
(P Suffix)
14-Lead
Narrow-Body SO
(S Suffix)
1
14
OUT A
1
2
3
4
5
6
7
14 OUT D
13
Applications for these amplifiers include safety monitoring,
portable equipment, battery and power supply control, and
signal conditioning and interface for transducers in very low
power systems.
–IN A
+IN A
V+
–IN D
OP481
12 +IN D
11 V–
OP481
The output’s ability to swing rail-to-rail and not increase supply
current, when the output is driven to a supply voltage, enables
the OP181 family to be used as comparators in very low power
systems. This is enhanced by their fast saturation recovery time.
Propagation delays are 250 µs.
8
7
10 +IN C
+IN B
–IN B
OUT B
9
8
–IN C
14-Lead TSSOP
(RU Suffix)
OUT C
1
14
The OP181/OP281/OP481 are specified over the extended
industrial (–40°C to +85°C) temperature range. The OP181,
single, and OP281, dual, amplifiers are available in 8-pin plastic
DIPs and SO surface mount packages. The OP281 is also
available in 8-lead TSSOP. The OP481 quad is available in 14-
pin DIPs, narrow 14-pin SO and TSSOP packages.
OP481
NOTE: PIN ORIENTATION IS EQUIVALENT FOR
EACH PACKAGE VARIATION
7
8
REV. 0
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 617/329-4700
Fax: 617/326-8703
World Wide Web Site: http://www.analog.com
© Analog Devices, Inc., 1996
OP181/OP281/OP481–SPECIFICATIONS
ELECTRICAL SPECIFICATIONS(@ VS = +3.0 V, VCM = 1.5 V, TA = +25؇C unless otherwise noted)
Parameter
Symbol
Conditions
Min
Typ
Max
Units
INPUT CHARACTERISTICS
Offset Voltage
VOS
Note 1
1.5
2.5
10
7
mV
mV
nA
nA
V
–40°C ≤ TA ≤ +85°C
–40°C ≤ TA ≤ +85°C
–40°C ≤ TA ≤ +85°C
Input Bias Current
Input Offset Current
Input Voltage Range
IB
IOS
3
0.1
0
2
Common-Mode Rejection Ratio
CMRR
AVO
VCM = 0 V to 2.0 V,
–40°C ≤ TA ≤ +85°C
RL = 1 MΩ, VO = 0.3 V to 2.7 V
–40°C ≤ TA ≤ +85°C
65
5
2
95
13
dB
Large Signal Voltage Gain
V/mV
V/mV
µV/°C
pA/°C
pA/°C
Offset Voltage Drift
Bias Current Drift
Offset Current Drift
∆VOS/∆T
∆IB/∆T
∆IOS/∆T
10
20
2
OUTPUT CHARACTERISTICS
Output Voltage High
VOH
VOL
ISC
RL = 100 kΩ to GND,
–40°C ≤ TA ≤ +85°C
RL = 100 kΩ to V+,
–40°C ≤ TA ≤ +85°C
2.925
2.96
V
Output Voltage Low
Short Circuit Limit
25
±1.1
75
mV
mA
POWER SUPPLY
Power Supply Rejection Ratio
PSRR
ISY
VS = 2.7 V to 12 V
–40°C ≤ TA ≤ +85°C
VO = 0 V
76
95
3
dB
µA
µA
Supply Current/Amplifier
4
5
–40°C ≤ TA ≤ +85°C
DYNAMIC PERFORMANCE
Slew Rate
Turn On Time
SR
RL = 100 kΩ, CL = 50 pF
AV = 1, VO = 1
AV = 20, VO = 1
25
40
50
65
95
70
V/ms
µs
µs
µs
kHz
Degrees
Turn On Time
Saturation Recovery Time
Gain Bandwidth Product
Phase Margin
GBP
φo
NOISE PERFORMANCE
Voltage Noise
Voltage Noise Density
Current Noise Density
en p-p
en
in
0.1 Hz to 10 Hz
f = 1 kHz
10
75
<1
µV p-p
nV/√Hz
pA/√Hz
NOTES
1VOS is tested under no load condition.
Specifications subject to change without notice.
REV. 0
–2–
OP181/OP281/OP481
ELECTRICAL SPECIFICATIONS (@ VS = +5.0 V, VCM = 2.5 V, TA = +25؇C unless otherwise noted1)
Parameter
Symbol
Conditions
Min
Typ
Max
Units
INPUT CHARACTERISTICS
Offset Voltage
VOS
Note 1
0.1
1.5
2.5
10
7
mV
mV
nA
nA
V
–40°C ≤ TA ≤ +85°C
–40°C ≤ TA ≤ +85°C
–40°C ≤ TA ≤ +85°C
Input Bias Current
Input Offset Current
Input Voltage Range
IB
IOS
3
0.1
0
4
Common-Mode Rejection Ratio
CMRR
AVO
VCM = 0 V to 4.0 V,
–40°C ≤ TA ≤ +85°C
RL = 1 MΩ , VO = 0.5 V to 4.5 V
–40°C ≤ TA ≤ +85°C
–40°C to +85°C
65
5
2
90
15
dB
Large Signal Voltage Gain
V/mV
V/mV
µV/°C
pA/°C
pA/°C
Offset Voltage Drift
Bias Current Drift
Offset Current Drift
∆VOS/∆T
∆IB/∆T
∆IOS/∆T
10
20
2
OUTPUT CHARACTERISTICS
Output Voltage High
VOH
VOL
ISC
RL = 100 kΩ to GND,
–40°C ≤ TA ≤ +85°C
RL = 100 kΩ to V+,
–40°C ≤ TA ≤ +85°C
4.925
4.96
V
Output Voltage Low
Short Circuit Limit
25
±3.5
75
mV
mA
POWER SUPPLY
Power Supply Rejection Ratio
PSRR
ISY
VS = 2.7 V to 12 V,
–40°C ≤ TA ≤ +85°C
VO = 0 V
76
95
3.2
dB
µA
µA
Supply Current/Amplifier
4
5
–40°C ≤ TA ≤ +85°C
DYNAMIC PERFORMANCE
Slew Rate
Saturation Recovery Time
Gain Bandwidth Product
Phase Margin
SR
RL = 100 kΩ, CL = 50 pF
27
V/ms
µs
kHz
120
100
74
GBP
φo
Degrees
NOISE PERFORMANCE
Voltage Noise
Voltage Noise Density
Current Noise Density
en p-p
en
in
0.1 Hz to 10 Hz
f = 1 kHz
10
75
<1
µV p-p
nV/√Hz
pA/√Hz
NOTES
1VOS is tested under a no load condition.
Specifications subject to change without notice.
REV. 0
–3–
OP181/OP281/OP481–SPECIFICATIONS
ELECTRICAL SPECIFICATIONS
(@ VS = ±5 V, TA = +25؇C unless otherwise noted)
Parameter
Symbol
Conditions
Min
Typ
Max
Units
INPUT CHARACTERISTICS
Offset Voltage
VOS
Note 1
0.1
1.5
2.5
10
7
mV
mV
nA
nA
V
–40°C ≤ TA ≤ +85°C
–40°C ≤ TA ≤ +85°C
–40°C ≤ TA ≤ +85°C
Input Bias Current
IB
IOS
3
0.1
Input Offset Current
Input Voltage Range
Common-Mode Rejection
–5
+4
CMRR
AVO
VCM = –5.0 V to +4.0 V,
–40°C ≤ TA ≤ +85°C
RL = 1 MΩ, VO = ±4.0 V,
–40°C ≤ TA ≤ +85°C
–40°C to +85°C
65
5
2
95
13
dB
Large Signal Voltage Gain
V/mV
V/mV
µV/°C
pA/°C
pA/°C
Offset Voltage Drift
Bias Current Drift
Offset Current Drift
∆VOS/∆T
∆IB/∆T
∆IOS/∆T
10
20
2
OUTPUT CHARACTERISTICS
Output Voltage Swing
VO
ISC
RL = 100 kΩ to GND,
–40°C ≤ TA ≤ +85°C
±4.925
±4.98
V
Short Circuit Limit
12
mA
POWER SUPPLY
Power Supply Rejection Ratio
PSRR
ISY
VS = ±1.35 V to ±6 V,
–40°C ≤ TA ≤ +85°C
VO = 0 V
76
95
3.3
dB
µA
µA
Supply Current/Amplifier
5
6
–40°C ≤ TA ≤ +85°C
DYNAMIC PERFORMANCE
Slew Rate
Gain Bandwidth Product
Phase Margin
±SR
GBP
φo
RL = 100 kΩ, CL = 50 pF
28
105
75
V/ms
kHz
Degrees
NOISE PERFORMANCE
Voltage Noise
Voltage Noise Density
Voltage Noise Density
Current Noise Density
en p-p
en
en
0.1 Hz to 10 Hz
f = 1 kHz
f = 10 kHz
10
85
75
<1
µV p-p
nV/√Hz
nV/√Hz
pA/√Hz
in
NOTES
1VOS is tested under no load condition.
Specifications subject to change without notice.
REV. 0
–4–
OP181/OP281/OP481
ABSOLUTE MAXIMUM RATINGS
ORDERING GUIDE
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +16 V
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . Gnd to VS + 10 V
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . ±3.5 V
Output Short-Circuit Duration to Gnd . . . . . . . . . . Indefinite
Storage Temperature Range
P, S, RU Package . . . . . . . . . . . . . . . . . . . –65°C to +150°C
Operating Temperature Range
OP181/OP281/OP481G . . . . . . . . . . . . . . . –40°C to +85°C
Junction Temperature Range
Temperature
Range
Package
Description
Package
Option
Model
OP181GP
OP181GS
OP281GP
OP281GS
–40°C to +85°C 8-Pin Plastic DIP
–40°C to +85°C 8-Pin SOIC
–40°C to +85°C 8-Pin Plastic DIP
–40°C to +85°C 8-Pin SOIC
N-8
SO-8
N-8
SO-8
RU-8
OP281GRU –40°C to +85°C 8-Pin TSSOP
OP481GP
OP481GS
–40°C to +85°C 14-Pin Plastic DIP N-14
–40°C to +85°C 14-Pin SOIC
OP481GRU –40°C to +85°C 14-Pin TSSOP
P, S, RU Package . . . . . . . . . . . . . . . . . . . –65°C to +150°C
Lead Temperature Range (Soldering, 60 sec) . . . . . . . +300°C
SO-14
RU-14
Package Type
JA*
JC
Units
8-Pin Plastic DIP (P)
8-Pin SOIC (S)
8-Pin TSSOP (RU)
14-Pin Plastic DIP (P)
14-Pin SOIC (S)
103
158
240
76
120
240
43
43
43
33
36
43
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
14-Pin TSSOP (RU)
*θJA is specified for the worst case conditions, i.e., θJA is specified for device in socket
for P-DIP packages; θJA is specified for device soldered in circuit board for TSSOP
and SOIC packages.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the OP181/OP281/OP481 features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precau-
tions are recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
REV. 0
–5–
OP181/OP281/OP481–Typical Characteristics
50
45
40
35
30
25
20
15
10
5
2000
1800
1600
1400
1200
1000
800
45
40
35
30
25
20
15
10
5
V
T
= +2.7V
= +25؇C
V
= +5V
S
= +25؇C
S
T
V
= +5V
A
A
S
600
400
200
0
0
0
–1.0 –0.8 –0.6 –0.4 –0.2
0
0.2 0.4 0.6 0.8 1.0
–1.0 –0.8 –0.6 –0.4 –0.2
0
0.2 0.4 0.6 0.8 1.0
–40 –20
0
20 40 60 80 100 120
INPUT OFFSET VOLTAGE – mV
INPUT OFFSET VOLTAGE – mV
TEMPERATURE – ؇C
Figure 1. Input Offset Voltage
Distribution
Figure 2. Input Offset Voltage
Distribution
Figure 3. Input Offset Voltage vs.
Temperature
0
1.0
0.5
0.4
–0.5
V
= +5V
S
= +25؇C
0.5
0.0
V
= +5V
S
T
V
= +5V
A
S
–1.0
–1.5
0.3
–0.5
–1.0
–1.5
0.2
0.1
0
–2.0
–2.5
–3.0
–3.5
–2.0
–2.5
–3.0
–3.5
–0.1
–0.2
–0.3
–0.4
–4.0
–4.5
–5.0
–40 –20
0
20 40 60 80 100 120
TEMPERATURE – ؇C
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
COMMON-MODE VOLTAGE – Volts
–40 –20
0
20 40 60 80 100 120
TEMPERATURE – ؇C
Figure 4. Input Bias Current vs.
Temperature
Figure 5. Input Bias Current vs.
Common-Mode Voltage
Figure 6. Input Offset Current vs.
Temperature
10,000
1,000
1,000
V
T
= +3V
= +25؇C
V
T
= +5V
= +25؇C
V
T
= ±5V
= +25؇C
S
A
S
A
S
A
1,000
100
100
100
SOURCE
SOURCE
SOURCE
10
10
SINK
SINK
SINK
10
1.0
1.0
1.0
0.1
0.1
0.1
1
10
100
1000
1
10
100
1000
1
10
100
1000
LOAD CURRENT – µA
LOAD CURRENT – µA
LOAD CURRENT – µA
Figure 7. Output Voltage to Supply
Rail vs. Load Current
Figure 8. Output Voltage to Supply
Rail vs. Load Current
Figure 9. Output Voltage to Supply
Rail vs. Load Current
REV. 0
–6–
OP181/OP281/OP481
70
60
50
40
30
20
10
0
70
60
50
40
30
20
10
0
70
V
T
R
= +5V
= +25؇C
= 100kΩ
V
T
R
= +3V
= +25؇C
= 100kΩ
V
= +2.7V
= +25؇C
= 100kΩ
S
A
S
A
S
60
50
40
30
20
10
0
T
A
R
L
L
L
0
0
0
45
45
45
90
90
90
135
180
225
270
135
180
225
270
135
180
225
270
–10
–10
–10
–20
–30
–20
–30
–20
–30
100
1k
10k
100k
1M
100
1k
10k
100k
1M
100
1k
10k
100k
1M
FREQUENCY – Hz
FREQUENCY – Hz
FREQUENCY – Hz
Figure 10. Open-Loop Gain and Phase
vs. Frequency
Figure 11. Open-Loop Gain and Phase Figure 12. Open-Loop Gain and Phase
vs. Frequency
vs. Frequency
70
60
50
V
T
R
= +5V
= +25؇C
= INFINITE
V
T
R
= ±5V
= +25؇C
= 100kΩ TO GROUND
S
S
60
50
40
30
20
10
0
A
A
L
V
T
= +5V
= +25؇C
40
L
S
A
0
30
MARKER @ 67nV/√Hz
45
20
90
10
135
180
225
270
0
–10
–20
–30
–40
–10
–20
–30
100
1k
10k
100k
1M
10
100
1k
10k
100k
1M
0
2k
4k
6k
8k
10k
FREQUENCY – Hz
FREQUENCY – Hz
FREQUENCY – Hz
Figure 13. Open-Loop Gain and Phase
vs. Frequency
Figure 14. Closed-Loop Gain vs.
Frequency
Figure 15. Voltage Noise Density vs.
Frequency
90
160
50
T
= +25؇C
V
= ±5V
A
S
V
T
R
= ±5V, +5V, +3V, +2.7V
= +25؇C
= INFINITE
V
V
R
= +5V
S
S
140
120
100
80
80
70
60
50
40
30
20
10
0
45
40
35
30
25
20
15
10
5
= ±50mV
= 100kΩ
= +25؇C
A
IN
V
= +5V
S
L
–OS
L
T
A
+OS
V
= +3V
S
60
40
20
0
–20
–40
–10
0
10
10
100
1k
10k
100k
1M
1k
10k
100k
FREQUENCY – Hz
1M
10M
100
CAPACITANCE – pF
1000
FREQUENCY – Hz
Figure 16. CMRR vs. Frequency
Figure 17. PSRR vs. Frequency
Figure 18. Small Signal Overshoot vs.
Load Capacitance
REV. 0
–7–
OP181/OP281/OP481
3
2
5
4.0
3.5
V
V
R
= +3V
V
= +3V
S
S
= 2Vp–p
= INFINITE
= +25؇C
IN
L
4
T
A
3.0
2.5
V
V
R
= +5V
S
= 4Vp–p
= INFINITE
= +25؇C
IN
3
2
1
0
L
2.0
1.5
T
A
1
0
1.0
0.5
0
10
100
1k
FREQUENCY – Hz
10k
100k
10
100
1k
FREQUENCY – Hz
10k
100k
–40 –20
0
20 40 60 80 100 120
TEMPERATURE – ؇C
Figure 20. Maximum Output Swing
vs. Frequency
Figure 21. Supply Current/Amplifier
vs. Temperature
Figure 19. Maximum Output Swing
vs. Frequency
3.50
4.5
T
= +25؇C
3.25
3.00
V
= +5V
A
S
4.0
3.5
V
= ±2.5V
= 1
= 100kΩ
= 50pF
= +25؇C
S
A2
0mV
A
R
C
T
2.75
2.50
2.25
V
L
L
100
90
3.0
2.5
2.0
A
2.00
1.75
1.50
1.25
1.00
1.5
10
1.0
0.5
0
0.75
0.50
0%
50mV
100µs
0.25
0.00
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
–40 –20
0
20 40 60 80 100 120
SUPPLY VOLTAGE – ±Volts
TEMPERATURE – ؇C
Figure 23. Supply Current/Amplifier
vs. Supply Voltage
Figure 24. Small Signal Transient
Response
Figure 22. Supply Current/Amplifier
vs. Temperature
VS = +5V
AV = 1
RL = 100kΩ
CL = 50pF
TA = +25؇C
VS = +2.7V
AV = 1
RL = 100kΩ
CL = 50pF
V
= ±1.35V
= 1
= 100kΩ
= 50pF
= +25؇C
A2
A2
S
2.50V
A2
0mV
0.50V
A
R
C
T
V
L
L
100
90
100
100
90
90
TA = +25؇C
A
10
10
10
0%
0%
0%
500mV
1V
100µs
100µs
50mV
100µs
Figure 26. Large Signal Transient
Response
Figure 27. Large Signal Transient
Response
Figure 25. Small Signal Transient
Response
REV. 0
–8–
OP181/OP281/OP481
120
105
90
V
T
R
=
=
=
+5V
+25؇C
∞
S
VS = ؎1.35V
RL = ∞
VIN = ؎1Vp-p
AT 2kHz
V
T
= +5V
= +25؇C
A2
2.50V
A2
0.00V
S
A
A
L
100
90
100
90
75
60
45
30
15
10
10
0%
0%
0
1V
1V
200µs
–15
500mV 500mV
50µs
–30
100
1k
10k
100k
1M
FREQUENCY – Hz
Figure 28. No Phase Reversal
Figure 29. Channel Separation vs.
Frequency
Figure 30. Saturation Recovery Time
VS = ؎2.5V
RL = ∞
A2
0.00V
CIRCUIT = AVOL
TA = +25؇C
100
90
10
0%
1V
500mV
100µs
Figure 31. Saturation Recovery Time
REV. 0
–9–
OP181/OP281/OP481
APPLICATIONS
THEORY OF OPERATION
where: VEE is the negative power supply for the amplifier, and
IN, MIN is the lowest input voltage excursion expected
V
The OPx81 family of op amps is comprised of extremely low
powered, rail-to-rail output amplifiers, requiring less than 4 µA
of quiescent current per amplifier. Many other competitors’
devices may be advertised as low supply current amplifiers but
draw significantly more current as the outputs of these devices
are driven to a supply rail. The OPx81’s supply current remains
under 4 µA even with the output driven to either supply rail.
Supply currents should meet the specification as long as the inputs
and outputs remain within the range of the power supplies.
For example, an OP181 is to be used with a single supply volt-
age of 5 V where the input signal could possibly go as low as
–1.0 V. Because the amplifier is powered from a single supply,
VEE is ground, so the necessary series resistance should be 2 kΩ.
Input Offset Voltage Nulling
The OPx81 family of op amps was designed for low offset
voltages less than 1 mV. The single OP181 does provide two
offset adjust terminals, should the user require greater precision.
In general, these terminals should be used only to zero amplifier
offsets and should not be used to adjust system offset voltages.
Figure 32 shows a simplified schematic of the OP181. A bipolar
differential pair is used in the input stage. PNP transistors are
used to allow the input stage to remain linear with the common-
mode range extending to ground. This is an important consider-
ation for single supply applications. The bipolar front end also
contributes less noise than a MOS front end with only nano-
amps of bias currents. The output of the op amp consists of a
pair of CMOS transistors in a common source configuration.
This setup allows the output of the amplifier to swing to within
millivolts of either supply rail. The headroom required by the
output stage is limited by the amount of current being driven
into the load. The lower the output current, the closer the
output can go to either supply rail. Figures 7, 8 and 9 show the
output voltage headroom versus load current. This behavior is
typical of rail-to-rail output amplifiers.
A 20 kΩ potentiometer connected to the offset adjust terminals,
with the wiper connected to VEE, can be used to reduce the
offset voltage of the amplifier. The OP181 should be connected
in the unity-gain configuration (as shown in Figure 33) or in a
gain configuration. The potentiometer should be adjusted until
VOUT is minimized. The wiper of the potentiometer must be
connected to VEE; connecting it to the positive supply rail could
damage the device.
+5V
7
2
OP181
6
V
OUT
4
V
CC
3
5
1
20kΩ
POT.
V
= –5V
EE
OUT
Figure 33. Offset Voltage Nulling Circuit
Input Common-Mode Voltage Range
+IN
–IN
The OPx81 is rated with an input common-mode voltage range
from VEE to 1 volt under VCC. However, the op amp can still
operate even with a common-mode voltage that is slightly less
than VEE. Figure 34 shows an OP181 configured as a difference
amplifier with a single supply voltage of +3 V. Negative dc
voltages are applied at both input terminals creating a common-
mode voltage that is less than ground. A 400 mV p-p input
signal is then applied to the noninverting input. Figure 35 shows
a picture of the input and output waves. Notice how the output
of the amplifier also drops slightly negative without distortion.
V
EE
Figure 32. Simplified Schematic of the OP181
Input Overvoltage Protection
The input stage to the OPx81 family of op amps consists of a
PNP differential pair. If the base voltage of either of these input
transistors drops to more than 0.6 V below the negative supply,
the input ESD protection diodes will become forward biased,
and large currents will begin to flow. In addition to possibly
damaging the device, this will create a phase reversal effect at
the output. To prevent these effects from happening, the input
current should be limited to less than 0.5 mA.
100kΩ
+3V
100kΩ
V
100kΩ
OUT
–0.27V
OP181
V
= 1kHz AT
IN
400mV p-p
100kΩ
This can be done quite easily by placing a resistor in series with
the input to the device. The size of the resistor should be pro-
portional to the lowest possible input signal excursion and can
be found using the following formula:
–0.1V
Figure 34. OP181 Configured as a Difference Amplifier
Operating at VCM < 0 V
VEE −VIN, MIN
R =
0.5 ×10−3
REV. 0
–10–
OP181/OP281/OP481
0.2ms
100
90
100
90
V
OUT
0V
V
IN
10
10
0%
0%
0.1V
Figure 37. Ringing and Overshoot of the Output of the
Amplifier
Figure 35. Input and Output Signals with VCM < 0 V
Overdrive Recovery Time
A Micropower Reference Voltage Generator
Many single supply circuits are configured with the circuit
biased to 1/2 of the supply voltage. In these cases, a false-
ground reference can be created by using a voltage divider
buffered by an amplifier. Figure 38 shows the schematic for
such a circuit.
The amount of time it takes for an amplifier to recover from
saturation can be an important consideration when using an
amplifier as a comparator or when outputs can be driven to the
supplies. The overdrive recovery time for the OP181 is 50 µs
with the amplifier running from a 3 volt supply and increases
to 100 µs with a 10 volt supply. Figure 36 shows the result of
the OP181 running from a 3 V supply with its output being
overdriven.
The two 1 MΩ resistors generate the reference voltage while
drawing only 1.5 µA of current from a 3 V supply. A capacitor
connected from the inverting terminal to the output of the op
amp provides compensation to allow for a bypass capacitor to be
connected at the reference output. This bypass capacitor helps
establish an ac ground for the reference output. The entire
reference generator draws less than 5 µA from a 3 V supply
source.
0.2ms
V
IN
100
SCALE 0.1V 90
V
S
= +3V
A
V
= +100
0V
V
OUT
+3V TO +12V
SCALE 1V
10
0%
0V
10kΩ
0.1V
0.022µF
Figure 36. Output of the Op Amp Recovering from
Saturation
7
2
Capacitive Loading
100Ω
1MΩ
OP181
6
Most low supply current amplifiers have difficulty driving
capacitive loads due to the higher currents required from the
output stage for such loads. Higher capacitance at the output
will increase the amount of overshoot and ringing in the
amplifier’s step response and could even affect the stability of
the device. However, through careful design of the output stage
and its high phase margin, the OPx81 family can tolerate some
degree of capacitive loading. Figure 37 shows the step response
of an OP181 with a 10 nF capacitor connected at the output.
Notice that the overshoot of the output does not exceed more
than 10% with such a load, even with a supply voltage of only
+3 V.
V
REF
+1.5V TO +6V
3
1µF
4
1MΩ
1µF
Figure 38. A Micropower Bias Voltage Generator
A Window Comparator
The extremely low power supply current demands of the OPx81
family make it ideal for use in long life battery powered applica-
tions such as a monitoring system. Figure 39 shows a circuit
that uses the OP281 as a window comparator.
REV. 0
–11–
OP181/OP281/OP481
+3V
creates a very small voltage drop. The voltage at the inverting
terminal becomes equal to the voltage at the noninverting
terminal through the feedback of Q1, which is a 2N2222 or
equivalent NPN transistor. This makes the voltage drop across
R1 equal to the voltage drop across RSENSE. Therefore, the
current through Q1 becomes directly proportional to the current
through RSENSE, and the output voltage is given by:
+3V
+3V
5.1kΩ
V
OUT
R1
V
H
D1
10kΩ
Q1
A1
R2
OP281-A
5.1kΩ
V
IN
2kΩ
R2
R1
+3V
A2
+3V
VOUT = VEE
−
× RSENSE × IL
D2
R3
R4
V
The voltage drop across R2 increases with IL increasing, so
OUT decreases with higher supply current being sensed. For
the element values shown, the VOUT transfer characteristic is
L
OP281-B
V
–2.5 V/A, decreasing from VEE
.
+5V
Figure 39. Using the OP281 as a Window Comparator
The threshold limits for the window are set by VH and VL,
provided that VH > VL. The output of A1 will stay at the
negative rail, in this case ground, as long as the input voltage is
less than VH. Similarly, the output of A2 will stay at ground as
long the input voltage is higher than VL. As long as VIN remains
between VL and VH, the outputs of both op amps will be 0 V.
With no current flowing in either D1 or D2, the base of Q1 will
stay at ground, putting the transistor in cutoff and forcing VOUT
to the positive supply rail. If the input voltage rises above VH,
the output of A2 stays at ground, but the output of A1 will go to
the positive rail, and D1 will conduct current. This creates a
base voltage that will turn on Q1 and drive VOUT low. The same
condition occurs if VIN falls below VL with A2’s output going
high, and D2 conducting current. Therefore, VOUT will be high
if the input voltage is between VL and VH, and VOUT will be low
if the input voltage moves outside of that range.
R2
2.49kΩ
V
OUT
Q1
+5V
R1
100Ω
OP181
0.1Ω
RETURN TO
GROUND
R
SENSE
Figure 40. A Low-Side Load Current Monitor
Low Voltage Half-Wave and Full-Wave Rectifiers
Because of its quick overdrive recovery time, an OP281 can be
configured as a full-wave rectifier for low frequency (<500 Hz)
applications. Figure 41 shows the schematic.
The R1 and R2 voltage divider sets the upper window voltage,
and the R3 and R4 voltage divider sets the lower voltage for the
window. For the window comparator to function properly, VH
must be a greater voltage than VL.
R1 = 100kΩ
R2 = 100kΩ
+3V
+3V
R2
R1+ R2
2kΩ
= 2V p-p
FULL-WAVE
RECTIFIED
OUTPUT
VH
VL
=
A2
A1
V
IN
OP281-B
OP281-A
R4
R3 + R4
=
HALF-WAVE
RECTIFIED
OUTPUT
The 2 kΩ resistor connects the input voltage to the input termi-
nals to the op amps. This protects the OP281 from possible
excess current flowing into the input stages of the devices. D1
and D2 are small-signal switching diodes (1N4446 or equiva-
lent), and Q1 is a 2N2222 or equivalent NPN transistor.
Figure 41. Single Supply Full- and Half-Wave Rectifiers
Using an OP281
A Low-Side Current Monitor
100
In the design of power supply control circuits, a great deal of
design effort is focused on ensuring a pass transistor’s long-term
reliability over a wide range of load current conditions. As a
result, monitoring and limiting device power dissipation is of
prime importance in these designs. Figure 40 shows an example
of a +5 V, single-supply current monitor that can be incorpo-
rated into the design of a voltage regulator with fold-back
current limiting or a high current power supply with crowbar
protection. The design capitalizes on the OP181’s common-
mode range that extends to ground. Current is monitored in the
SCALE 0.1V/DIV
90
10
SCALE 0.1ms/DIV
0%
Figure 42. Full-Wave Rectified Signal
power supply return path where a 0.1 Ω shunt resistor, RSENSE
,
REV. 0
–12–
OP181/OP281/OP481
The OP281-B amplifier can provide up to 15 dB of gain for the
headset speaker. Incoming audio signals are ac coupled to a
10 kΩ potentiometer that is used to adjust the volume. Again,
two 1 MΩ resistors provide the dc offset with a 1 µF capacitor
establishing an ac ground for the volume control potentiometer.
Because the OP281 is a rail-to-rail output amplifier, it would
have difficulty driving a 600 Ω speaker directly. Here, a class AB
buffer is used to isolate the load from the amplifier and also
provide the necessary current drive to the speaker. By placing
the buffer in the feedback loop of the op amp, crossover
distortion can be minimized. Q1 and Q2 should have minimum
betas of 100. The 600 Ω speaker is ac coupled to the emitters to
prevent any quiescent current from flowing in the speaker. The
1 µF coupling capacitor makes an equivalent high pass filter
cutoff at 265 Hz with a 600 Ω load attached. Again, this does
not pose a problem, as it is outside the frequency range for
telephone audio signals.
Amplifier A1 is used as a voltage follower that will only track the
input voltage when it is greater than 0 V. This provides a half-
wave rectification of the input signal to the noninverting
terminal of amplifier A2. When A1’s output is following the
input, the inverting terminal of A2 will also follow the input
from the virtual ground between the inverting and noninverting
terminals of A2. With no potential difference across R1, no
current flows through either R1 or R2, therefore the output of
A2 will also follow the input. Now, when the input voltage goes
below 0 V, the noninverting terminal of A2 becomes 0 V. This
makes A2 work as an inverting amplifier with a gain of 1 and
provides a full-wave rectified version of the input signal. A 2 kΩ
resistor in series with A1’s noninverting input protects the
device when the input signal becomes less than ground.
A Battery Powered Telephone Headset Amplifier
Figure 43 shows how the OP281 can be used as a two-way
amplifier in a telephone headset. One side of the OP281 can be
used as an amplifier for the microphone, while the other side
can be used to drive the speaker. A typical telephone headset
uses a 600 Ω speaker and an electret microphone that requires a
supply voltage and a biasing resistor.
The circuit in Figure 43 draws around 250 µA of current. The
class AB buffer has a quiescent current of 140 µA while roughly
100 µA is drawn by the microphone itself. A CR2032 3 V
lithium battery has a life expectancy of 160 mA hours, which
means this circuit could run continuously for 640 hours on a
single battery.
0.1µF
11kΩ
300kΩ
SPICE Macro-Model
+3V
+3V
+3V
* OP181 SPICE Macro-model
* 9/96, Ver. 1
1µF
2.2kΩ
1MΩ
1µF
MIC OUT
*
OP281-A
ELECTRET
MIC
* Copyright 1996 by Analog Devices
*
1MΩ
* Refer to “README.DOC” file for License Statement. Use of this
* model indicates your acceptance of the terms and provisions in
1µF
10kΩ
50kΩ
* the License Statement.
*
+3V
* Node Assignments
*
noninverting input
20kΩ
*
*
*
*
*
*
|
|
|
|
|
|
1
inverting input
+3V
Q1
|
|
|
|
|
2
positive supply
1µF
INPUT
+3V
1µF
|
|
|
negative supply
|
|
output
|
|
10kΩ
POT.
OP281-B
Q2
600Ω
|
|
1MΩ
1µF
1MΩ
SPEAKER
20kΩ
.SUBCKT OP181
99
50
45
*
* INPUT STAGE
*
Figure 43. A Battery Powered Telephone Headset
Two-Way Amplifier
Q1
Q2
I1
EOS
IOS
RC1
RC2
RE1
RE2
V1
4
6
99
7
1
4
6
3
5
1
7
8
2
2
3
5
PIX
PIX
The OP281-A op amp provides about 29 dB of gain for audio
signals coming from the microphone. The gain is set by the
300 kΩ and 11 kΩ resistors. The gain bandwidth product of the
amplifier is 95 kHz, which, for the set gain of 28, yields a –3 dB
rolloff at 3.4 kHz. This is acceptable since telephone audio is
band limited for 300 kHz to 3 kHz signals. If higher gain is
required for the microphone, an additional gain stage should be
used, as adding any more gain to the OP281 would limit the
audio bandwidth. A 2.2 kΩ resistor is used to bias the electret
microphone. This resistor value may vary depending on the
specifications on the microphone being used. The output of the
microphone is ac coupled to the noninverting terminal of the op
amp. Two 1 MΩ resistors are used to provide the dc offset for
single supply use.
1.28E-6
POLY(1) (12, 98) 80E-6 1
1E-10
50 500E3
50 500E3
8
8
108
108
99 13 DC .9
99 14 DC .9
V2
D1
D2
*
3
5
13 DX
14 DX
* CMRR76dB, ZERO AT 1kHz
*
REV. 0
–13–
OP181/OP281/OP481
ECM1 11 98 POLY(2) (1, 98) (2, 98) 0 .5 .5
R1
C1
R2
*
11 12 1.59E6
11 12 100E-12
12 98 283
* POLE AT 900kHz
*
EREF 98
0
(90, 0)
1
G1
R3
C2
*
98 20 (4, 6)
20 98 1E6
20 98 177E-15
1E-6
* POLE AT 500kHz
*
E2
R4
C3
*
21 98 (20, 98)
21 22 1E6
22 98 320E-15
1
* GAIN STAGE
*
CF
R5
G3
D3
D4
V3
V4
*
45 40 8. 5E-12
40 98 65. 65E6
98 40 (22, 98)
40 41 DX
42 40 DX
99 41 DC 0.5
42 50 DC 0.5
4.08E-7
* OUTPUT STAGE
*
ISY 99 50 1.375E-6
RS1 99 90 10E6
RS2 90 50 10E6
M1
M2
45 46 99 99
45 47 50 50
POX L=1.5u W=300u
NOX L=1.5u W=300u
EG1 99 46 POLY(1) (98, 40) 0.77
1
EG2 47 50 POLY(1) (40, 98) 0.77
1
*
* MODELS
*
.MODEL POX PMOS (LEVEL=2, KP=25E-6, VTO=-0.75, LAMBDA=0.01)
.MODEL NOX NMOS (LEVEL=2, KP=25E-6, VTO=0.75, LAMBDA=0.01)
.MODEL PIX PNP (BF=200)
.MODEL DX D(IS=1E-14)
.ENDS
REV. 0
–14–
OP181/OP281/OP481
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
14-Lead Plastic DIP
(N-14)
8-Lead Plastic DIP
(N-8)
0.795 (20.19)
0.725 (18.42)
0.430 (10.92)
0.348 (8.84)
14
1
8
7
8
5
4
0.280 (7.11)
0.240 (6.10)
0.280 (7.11)
0.240 (6.10)
0.325 (8.25)
0.300 (7.62)
0.195 (4.95)
0.115 (2.93)
1
0.325 (8.25)
0.300 (7.62)
0.060 (1.52)
0.015 (0.38)
PIN 1
0.060 (1.52)
0.015 (0.38)
PIN 1
0.210 (5.33)
0.195 (4.95)
MAX
0.210 (5.33)
MAX
0.130
(3.30)
MIN
0.115 (2.93)
0.160 (4.06)
0.130
(3.30)
MIN
0.160 (4.06)
0.115 (2.93)
0.115 (2.93)
0.015 (0.381)
0.008 (0.204)
SEATING
PLANE
0.022 (0.558)
0.014 (0.356)
0.100 0.070 (1.77)
0.015 (0.381)
0.008 (0.204)
SEATING
PLANE
(2.54)
BSC
0.100
(2.54)
BSC
0.022 (0.558)
0.014 (0.356)
0.070 (1.77)
0.045 (1.15)
0.045 (1.15)
14-Lead Narrow Body SOIC
(SO-14)
8-Lead SOIC
(SO-8)
0.1968 (5.00)
0.1890 (4.80)
0.3444 (8.75)
0.3367 (8.55)
8
1
5
4
14
8
7
0.1574 (4.00)
0.1497 (3.80)
0.1574 (4.00)
0.1497 (3.80)
0.2440 (6.20)
0.2284 (5.80)
0.2440 (6.20)
0.2284 (5.80)
1
PIN 1
0.0688 (1.75)
0.0532 (1.35)
0.0688 (1.75)
0.0532 (1.35)
PIN 1
0.0196 (0.50)
0.0196 (0.50)
x 45°
x 45°
0.0098 (0.25)
0.0040 (0.10)
0.0098 (0.25)
0.0040 (0.10)
0.0099 (0.25)
0.0099 (0.25)
8°
0°
8°
0°
0.0500
(1.27)
BSC
0.0500
(1.27)
BSC
0.0192 (0.49)
0.0138 (0.35)
0.0192 (0.49)
0.0138 (0.35)
SEATING
PLANE
SEATING
PLANE
0.0098 (0.25)
0.0075 (0.19)
0.0500 (1.27)
0.0160 (0.41)
0.0500 (1.27)
0.0160 (0.41)
0.0099 (0.25)
0.0075 (0.19)
14-Lead TSSOP
(RU-14)
8-Lead TSSOP
(RU-8)
0.201 (5.10)
0.193 (4.90)
0.122 (3.10)
0.114 (2.90)
14
8
7
8
5
1
1
4
PIN 1
PIN 1
0.0256 (0.65)
BSC
0.006 (0.15)
0.002 (0.05)
0.006 (0.15)
0.002 (0.05)
0.0433
(1.10)
MAX
0.0433
(1.10)
MAX
0.028 (0.70)
0.020 (0.50)
8°
0°
0.028 (0.70)
0.020 (0.50)
8°
0°
0.0118 (0.30)
0.0075 (0.19)
0.0256
(0.65)
BSC
0.0118 (0.30)
0.0075 (0.19)
SEATING
PLANE
0.0079 (0.20)
0.0035 (0.090)
SEATING
PLANE
0.0079 (0.20)
0.0035 (0.090)
REV. 0
–15–
–16–
相关型号:
OP181GS-REEL
IC OP-AMP, 2500 uV OFFSET-MAX, 0.105 MHz BAND WIDTH, PDSO8, SOIC-8, Operational Amplifier
ADI
©2020 ICPDF网 联系我们和版权申明