AD9980KSTZ-95 [ADI]
High Performance 8-Bit Display Interface; 高性能8位显示器接口
| 型号： | AD9980KSTZ-95 |
| 厂家： | 
ADI |
| 描述： | High Performance 8-Bit Display Interface |
| 文件： | 总44页 (文件大小：1433K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
High Performance
8-Bit Display Interface
AD9980
FEATURES
FUNCTIONAL BLOCK DIAGRAM
95 MSPS maximum conversion rate
9% or less p-p PLL clock jitter at 95 MSPS
Automated offset adjustment
2:1 input mux
Power-down via dedicated pin or serial register
4:4:4, 4:2:2, and DDR output format modes
Variable output drive strength
Odd/even field detection
8
8
8
AUTO OFFSET
AD9980
PR/RED
PR/RED
1
0
8
8
8
8
IN
IN
2:1
MUX
8-BIT
ADC
CB/CR/RED
OUT
CLAMP
CLAMP
CLAMP
PGA
PGA
PGA
AUTO OFFSET
Y/GREEN
Y/GREEN
1
0
8
8
IN
IN
2:1
MUX
8-BIT
ADC
Y/GREEN
OUT
AUTO OFFSET
PB/BLUE
PB/BLUE
1
0
IN
2:1
MUX
8-BIT
ADC
CB/BLUE
OUT
IN
External clock input
Regenerated Hsync output
Programmable output high impedance control
Hsyncs per Vsyncs counter
HSYNC1
HSYNC2
2:1
MUX
DTACK
SOGOUT
SYNC
VSYNC1
VSYNC2
2:1
MUX
Pb-free package
PROCESSING
O/E FIELD
HSOUT
PLL
POWER
MANAGEMENT
SOGIN1
SOGIN2
2:1
MUX
APPLICATIONS
Advanced TVs
Plasma display panels
LCD TV
VSOUT/A0
EXTCLK/COAST
CLAMP
FILT
REFHI
VOLTAGE
REFS
SDA
SCL
REFCM
REFLO
SERIAL REGISTER
HDTV
RGB graphics processing
LCD monitors and projectors
Scan converters
Figure 1.
GENERAL DESCRIPTION
The AD9980 is a complete, 8-bit, 95 MSPS, monolithic analog
interface optimized for capturing YPbPr video and RGB
graphics signals. Its 95 MSPS encode rate capability and full-
power analog bandwidth of 200 MHz supports all HDTV
video modes and graphics resolutions up to XGA (1024 × 768
at 85 Hz).
With internal Coast generation, the PLL maintains its output
frequency in the absence of sync input. A 32-step sampling
clock phase adjustment is provided. Output data, sync, and
clock phase relationships are maintained.
The auto-offset feature can be enabled to automatically restore
the signal reference levels and to automatically calibrate out any
offset differences between the three channels. The AD9980 also
offers full sync processing for composite sync and sync-on-
green applications. A clamp signal is generated internally or
may be provided by the user through the CLAMP input pin.
The AD9980 includes a 95 MHz triple ADC with an internal
reference, a phase-locked loop (PLL), programmable gain,
offset, and clamp controls. The user provides only 3.3 V and
1.8 V power supplies and an analog input. Three-state CMOS
outputs may be powered from 1.8 V to 3.3 V.
Fabricated in an advanced CMOS process, the AD9980 is
provided in a space-saving, 80-pin, Pb-free, LQFP surface
mount plastic package. It is specified over the 0°C to +70°C
temperature range.
The AD9980’s on-chip PLL generates a sample clock from
the three-level sync (for YPbPr video) or the horizontal sync
(for RGB graphics). Sample clock output frequencies range from
10 MHz to 95 MHz. PLL clock jitter is 9% or less p-p typical at
95 MSPS.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.326.8703
www.analog.com
© 2005 Analog Devices, Inc. All rights reserved.
AD9980
TABLE OF CONTENTS
Analog Interface specifications....................................................... 3
PLL Divider Control .................................................................. 28
Clock Generator Control .......................................................... 28
Phase Adjust................................................................................ 29
Input Gain ................................................................................... 29
Input Offset ................................................................................. 29
Hsync Controls........................................................................... 29
Vsync Controls ........................................................................... 30
Coast and Clamp Controls........................................................ 31
SOG Control ............................................................................... 33
Input and Power Control........................................................... 33
Output Control........................................................................... 34
Sync Processing .......................................................................... 35
Detection Status.......................................................................... 36
Polarity Status ............................................................................. 36
Hsync Count ............................................................................... 37
Two-Wire Serial Control Port....................................................... 38
Data Transfer via Serial Interface............................................. 38
PCB Layout Recommendations ............................................... 40
PLL ............................................................................................... 40
Outline Dimensions....................................................................... 42
Ordering Guide .......................................................................... 42
Electrical Characteristics............................................................. 3
Absolute Maximum Ratings............................................................ 5
Explanation of Test Levels........................................................... 5
ESD Caution.................................................................................. 5
Pin Configuration and Function Descriptions............................. 6
Design Guide................................................................................... 10
General Description................................................................... 10
Digital Inputs .............................................................................. 10
Input Signal Handling................................................................ 10
Hsync and Vsync Inputs............................................................ 10
Serial Control Port ..................................................................... 10
Output Signal Handling............................................................. 10
Clamping ..................................................................................... 10
Gain and Offset Control............................................................ 11
Timing Diagrams........................................................................ 19
Hsync Timing ............................................................................. 20
Coast Timing............................................................................... 20
Output Formatter ....................................................................... 20
Two-Wire Serial Register Map...................................................... 22
Detailed 2-Wire Serial Control Register Descriptions .............. 28
Chip Identification ..................................................................... 28
REVISION HISTORY
1/05—Initial Version: Revision 0
Rev. 0 | Page 2 of 44
AD9980
ANALOG INTERFACE SPECIFICATIONS
ELECTRICAL CHARACTERISTICS
VD = 3.3 V, VDD = 3.3 V, PVD = 1.8 V, DAVDD = 1.8 V, ADC clock = maximum conversion rate, full temperature range = 0°C to 70°C.
Table 1.
AD9980KSTZ-801
AD9980KSTZ-952
Parameter
RESOLUTION
Number of Bits
LSB Size
Temp
Test Level Min
Typ
Max
Min
Typ
Max
Unit
8
0.39
8
0.39
Bits
% of
Full
Scale
DC ACCURACY
Differential Nonlinearity
80 MSPS Conversion Rate
LSB
LSB
25°C
Full
I
VI
0.2
0.2
0.75
1.0
0.2
0.2
0.75
1.0
Differential Nonlinearity
95 MSPS Conversion Rate
Integral Nonlinearity
80 MSPS Conversion Rate
Integral Nonlinearity
25°C
Full
25°C
Full
25°C
Full
I
VI
I
VI
I
VI
0.6
0.75
0.3
0.3
0.6
0.9
1.5
2.25
1.0
1.3
2.25
3.2
LSB
LSB
LSB
0.3
0.3
1.0
1.3
95 MSPS Conversion Rate
No Missing Codes
ANALOG INPUT
Input Voltage Range
Minimum
Maximum
Gain Tempco
25°C
I
Guaranteed
Guaranteed
Full
Full
25°C
25°C
Full
Full
Full
VI
VI
V
V
V
0.5
0.5
V p-p
V p-p
ppm/°C
µA
µA
% FS
% FS
1.0
1.0
105
105
Input Bias Current
1
1
9
1
1
Input Full-Scale Matching
Offset Adjustment Range
VI
VI
1
44
1
10
44
SWITCHING PERFORMANCE
Maximum Conversion Rate
Minimum Conversion Rate
Data to Clock Skew tSKEW
tBUFF
tSTAH
tDHO
tDAL
tDAH
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
25°C
Full
Full
VI
IV
IV
VI
VI
VI
VI
VI
VI
VI
VI
VI
IV
IV
IV
IV
80
95
MSPS
MSPS
ns
µs
µs
µs
µs
µs
Ns
10
+2
10
+2
−0.5
4.7
4.0
0
4.7
4.0
250
4.7
4.0
80
−0.5
4.7
4.0
0
4.7
4.0
250
4.7
4.0
95
tDSU
tSTASU
tSTOSU
µs
µs
Maximum PLL Clock Rate
Minimum PLL Clock Rate
PLL Jitter
MHz
MHz
ps p-p
ps p-p
ps/°C
10
10
750
15
980
15
Sampling Phase Tempco
DIGITAL INPUTS3
Input Voltage, High (VIH)
Input Voltage, Low (VIL)
Input Current, High (IIH)
Input Current, Low (IIL)
Input Capacitance
Full
Full
Full
Full
25°C
VI
VI
V
V
V
2.5
2.5
V
V
µA
µA
pF
0.8
0.8
–82
82
2
–82
82
2
Rev. 0 | Page 3 of 44
AD9980
AD9980KSTZ-801
AD9980KSTZ-952
Parameter
Temp
Test Level Min
Typ
Max
Min
Typ
Max
Unit
DIGITAL OUTPUTS
Output Voltage, High (VOH)
Output Voltage, Low (VOL)
Duty Cycle, DATACK
Output Coding
Full
Full
Full
VI
VI
IV
VDD − 0.2
VDD − 0.1
V
V
%
0.2
0.1
50
Binary
50
Binary
POWER SUPPLY
VD Supply Voltage
VDD Supply Voltage
PVD Supply Voltage
Full
Full
Full
IV
IV
IV
IV
V
V
V
V
3.13
1.7
1.7
3.3
3.3
1.8
1.8
233
42
11
10
953
18
55
3.47
3.47
1.9
3.13
1.7
1.7
3.3
3.3
1.8
1.8
240
49
8
12
993
18
55
3.47
3.47
1.9
V
V
V
V
mA
mA
mA
mA
mW
mA
mW
DAVD Supply Voltage
ID Supply Current (VD)
IDD Supply Current (VDD)4
IPVD Supply Current (PVD)
IDAVD Supply Current (DAVD)
Total Power Dissipation
Power-Down Supply Current
Power-Down Dissipation
DYNAMIC PERFORMANCE
Analog Bandwidth, Full Power
Crosstalk
Full
1.7
1.9
1.7
1.9
25°C
25°C
25°C
25°C
Full
VI
VI
VI
1070
27
81
1114
28
88
Full
Full
25°C
Full
V
V
200
60
200
60
MHz
dBc
THERMAL CHARACTERISTICS
V
V
16
35
16
35
°C/W
°C/W
θJC, Junction-to-Case
Thermal Resistance
θJA, Junction-to-Ambient
Thermal Resistance
1 Output drive strength = 0 was used for all 80 MHz parameters.
2 Output drive strength = 1 was used for all 95 MHz parameters.
3 Digital inputs are HSYNC0, HSYNC1, VSYNC0, VSYNC1, SDA, SCL, EXTCLK, CLAMP, and PWRDN.
4 DATACK load = 10 pF, data load = 5 pF.
Rev. 0 | Page 4 of 44
AD9980
ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter
Stresses above those listed under Absolute Maximum Ratings
Rating
may cause permanent damage to the device. This is a stress
rating only and functional operation of the device at these or
any other conditions outside of those indicated in the operation
sections of this specification is not implied. Exposure to
absolute maximum ratings for extended periods may affect
device reliability.
VD
VDD
PVD
DAVDD
Analog Inputs
REFHI
REFCM
3.6 V
3.6 V
1.98 V
1.98 V
VD to 0.0 V
VD to 0.0 V
VD to 0.0 V
VD to 0.0 V
5 V to 0.0 V
20 mA
−25°C to + 85°C
−65°C to + 150°C
150°C
EXPLANATION OF TEST LEVELS
Test Level
REFLO
Digital Inputs
Digital Output Current
Functional Temperature
Storage Temperature
Maximum Junction Temperature
I. 100% production tested.
II. 100% production tested at 25°C and sample tested at
specified temperatures.
III. Sample tested only.
IV. Parameter is guaranteed by design and characterization
testing.
V. Parameter is a typical value only.
VI. 100% production tested at 25°C; guaranteed by design and
characterization testing.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. 0 | Page 5 of 44
AD9980
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61
1
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
V
V
(3.3V)
BLUE <1>
BLUE <2>
BLUE <3>
BLUE <4>
BLUE <5>
BLUE <6>
BLUE <7>
GND
D
PIN 1
2
3
B
AIN0
GND
4
B
AIN1
5
(3.3V)
D
6
G
AIN0
GND
SOGIN0
(3.3V)
7
AD9980
TOP VIEW
(Not to Scale)
8
9
V
V
(3.3V)
DD
D
10
11
12
13
14
15
16
17
18
19
20
G
NC
NC
AIN1
GND
SOGIN1
(3.3V)
GREEN <0>
GREEN <1>
GREEN <2>
GREEN <3>
GREEN <4>
GREEN <5>
GREEN <6>
GREEN <7>
V
D
R
AIN0
GND
R
AIN1
PWRDN
REFLO
REFCM
REFHI
DAV (1.8)
DD
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
NC = NO CONNECT
Figure 2. Top View (Pin Down)
Table 3. Complete Pinout List
Pin Type
Mnemonic
Function
Value
Pin No.
14
16
6
10
2
4
70
68
71
69
8
12
721
73
721
17
Inputs
RAIN0
RAIN1
GAIN0
GAIN1
BAIN0
BAIN1
HSYNC0
HSYNC1
VSYNC0
VSYNC1
SOGIN0
SOGIN1
EXTCK
CLAMP
COAST
PWRDN
RED [7:0]
GREEN [7:0]
BLUE [7:0]
DATACK
Channel 0 Analog Input for Converter R
Channel 1 Analog Input for Converter R
Channel 0 Analog Input for Converter G
Channel 1 Analog Input for Converter G
Channel 0 Analog Input for Converter B
Channel 1 Analog Input for Converter B
Horizontal Sync Input for Channel 0
Horizontal Sync Input for Channel 1
Vertical Sync Input for Channel 0
Vertical Sync Input for Channel 1
Input for Sync-on-Green Channel 0
Input for Sync-on-Green Channel 1
External Clock Input
0.0 V to 1.0 V
0.0 V to 1.0 V
0.0 V to 1.0 V
0.0 V to 1.0 V
0.0 V to 1.0 V
0.0 V to 1.0 V
3.3 V CMOS
3.3 V CMOS
3.3 V CMOS
3.3 V CMOS
0.0 V to 1.0 V
0.0 V to 1.0 V
3.3 V CMOS
3.3 V CMOS
3.3 V CMOS
3.3 V CMOS
3.3 V CMOS
3.3 V CMOS
3.3 V CMOS
3.3 V CMOS
External Clamp Input Signal
External PLL Coast Signal Input
Power-Down Control
Outputs
Outputs of Converter R, Bit 7 is the MSB
Outputs of Converter G, Bit 7 is the MSB
Outputs of Converter B, Bit 7 is the MSB
Data Output Clock
28–35
42–49
54–61
25
Rev. 0 | Page 6 of 44
AD9980
Pin Type
Mnemonic
HSOUT
VSOUT
SOGOUT
O/E FIELD
FILT
REFLO
REFCM
REFHI
VD
Function
Value
Pin No.
Hsync Output Clock (Phase-Aligned with DATACK)
Vsync Output Clock
Sync-on-Green Slicer Output
3.3 V CMOS
3.3 V CMOS
3.3 V CMOS
3.3 V CMOS
23
222
24
21
Odd/Even Field Output
References
Connection for External Filter Components for Internal PLL
Connection for External Capacitor for Input Amplifier
Connection for External Capacitor for Input Amplifier
Connection for External Capacitor for Input Amplifier
Analog Power Supply
Output Power Supply
PLL Power Supply
Digital Logic Power Supply
Ground
78
18
19
20
Power Supply
3.3 V
1.8 V or 3.3 V
1.8 V
1.8 V
0 V
1, 5, 9, 13
26, 38, 52, 64
74, 76, 79
41
3, 7, 11, 15, 27,
39, 40, 53, 65,
75, 77, 80
VDD
PVD
DAVDD
GND
Control
SDA
SCL
A0
Serial Port Data I/O
Serial Port Data Clock (100 kHz Maximum)
Serial Port Address Input
3.3 V CMOS
3.3 V CMOS
3.3 V CMOS
66
67
222
1 EXTCLK and COAST share the same pin.
2 VSOUT and A0 share the same pin.
Rev. 0 | Page 7 of 44
AD9980
Table 4. Pin Function Descriptions
Pin
Description
INPUTS
RAIN0
GAIN0
BAIN0
RAIN1
GAIN1
BAIN1
Analog Input for the Red Channel 0.
Analog Input for the Green Channel 0.
Analog Input for the Blue Channel 0.
Analog Input for the Red Channel 1.
Analog Input for the Green Channel 1.
Analog Input for the Blue Channel 1. High impedance inputs that accept the red, green, and blue channel
graphics signals, respectively. The three channels are identical and can be used for any colors, but colors are
assigned for convenient reference. They accommodate input signals ranging from 0.5 V to 1.0 V full scale. Signals
should be ac-coupled to these pins to support clamp operation.
HSYNC0
HSYNC1
Horizontal Sync Input Channel 0.
Horizontal Sync Input Channel 1. These inputs receive a logic signal that establishes the horizontal timing
reference and provides the frequency reference for pixel clock generation. The logic sense of this pin can be
automatically determined by the chip or manually controlled by Serial Register 0x12, Bits [5:4] (Hsync polarity).
Only the leading edge of Hsync is used by the PLL; the trailing edge is used in clamp timing. When Hsync
polarity = 0, the falling edge of Hsync is used. When Hsync polarity = 1, the rising edge is active. The input
includes a Schmitt trigger for noise immunity.
VSYNC0
VSYNC1
Vertical Sync Input Channel 0.
Vertical Sync Input Channel 1. These are the inputs for vertical sync and provide timing information for
generation of the field (odd/even) and internal Coast generation. The logic sense of this pin can be automatically
determined by the chip or manually controlled by Serial Register 0x14, Bits [5:4] (Vsync polarity).
SOGIN0
SOGIN1
Sync-on-Green Input Channel 0.
Sync-on-Green Input Channel 1. These inputs are provided to assist with processing signals with embedded
sync, typically on the green channel. The pin is connected to a high speed comparator with an internally
generated threshold. The threshold level can be programmed in 8 mV steps to any voltage between 8 mV and
256 mV above the negative peak of the input signal. The default voltage threshold is 128 mV. When connected
to an ac-coupled graphics signal with embedded sync, it produces a noninverting digital output on SOGOUT.
(This is usually a composite sync signal, containing both vertical and horizontal sync information that must be
separated before passing the horizontal sync signal for Hsync processing.) When not used, this input should
be left unconnected. For more details on this function and how it should be configured, refer to the Sync-on-
Green section.
CLAMP
External Clamp Input (Optional). This logic input may be used to define the time during which the input signal is
clamped to ground or midscale. It should be exercised when the reference dc level is known to be present on
the analog input channels, typically during the back porch of the graphics signal. The CLAMP pin is enabled by
setting the control bit clamp function to 1, (Register 0x18, Bit 4; default is 0). When disabled, this pin is ignored
and the clamp timing is determined internally by counting a delay and duration from the trailing edge of the
Hsync input. The logic sense of this pin can be automatically determined by the chip or controlled by clamp
polarity Register 0x1B, Bits [7:6]. When not used, this pin may be left unconnected (there is an internal pull-down
resistor) and the clamp function programmed to 0.
EXTCLK/COAST
Coast Input to Clock Generator (Optional). This input may be used to cause the pixel clock generator to stop
synchronizing with Hsync and continue producing a clock at its current frequency and phase. This is useful when
processing signals from sources that fail to produce Hsync pulses during the vertical interval. The Coast signal is
generally not required for PC-generated signals. The logic sense of this pin can be determined automatically or
controlled by Coast polarity (Register 0x18, Bits [7:6]). When not used and EXTCLK is not used, this pin may be
grounded and Coast polarity programmed to 1. Input Coast polarity defaults to1 at power-up. This pin is shared
with the EXTCLK function, which does not affect Coast functionality. For more details on EXTCLK, see the
description in this section.
EXTCLK/COAST
PWRDN
External Clock. This allows the insertion of an external clock source rather than the internally generated, PLL
locked clock. EXTCLK is enabled by programming Register 0x03, Bit 2 to 1. This pin is shared with the Coast
function, which does not affect EXTCLK functionality. For more details on Coast, see the description in this
section.
Power-Down Control. This pin can be used along with Register 0x1E, Bit 3 for manual power-down control. If
manual power-down control is selected (Register 0x1E, Bit 4) and this pin is not used, it is recommended to set
the pin polarity (Register 0x1E, Bit 2) to active high and hardwire this pin to ground with a 10 kΩ resistor.
REFLO
REFCM
REFHI
Input Amplifier Reference. REFLO and REFHI are connected together through a 10 µF capacitor; REFCM is
connected through a 10 µF capacitor to ground. These are used for stability in the input PGA (programmable
gain amplifier) circuitry. See Figure 5.
Rev. 0 | Page 8 of 44
AD9980
Pin
FILT
Description
External Filter Connection. For proper operation, the pixel clock generator PLL requires an external filter.
Connect the filter shown in Figure 7 to this pin. For optimal performance, minimize noise and parasitics on this
node. For more information see the PCB Layout Recommendations section.
OUTPUTS
HSOUT
Horizontal Sync Output. A reconstructed and phase-aligned version of the Hsync input. Both the polarity and
duration of this output can be programmed via serial bus registers. By maintaining alignment with DATACK and
Data Outputs, data timing with respect to Hsync can always be determined.
VSOUT/A0
Vertical Sync Output. Pin shared with A0, serial port address. This can be either a separated Vsync from a
composite signal or a direct pass through of the Vsync signal. The polarity of this output can be controlled via a
serial bus bit. The placement and duration in all modes can be set by the graphics transmitter or the duration
can be set by Register 0x14 and Register 0x15. This pin is shared with the A0 function, which does not affect
Vsync output functionality. For more details on A0, see the description in the Serial Control Port section.
SOGOUT
Sync-On-Green Slicer Output. This pin outputs one of four possible signals (controlled by Register 0x1D,
Bits [1:0]): raw SOG, raw Hsync, regenerated Hsync from the filter, or the filtered Hsync. See the sync processing
block diagram (Figure 8) to view how this pin is connected. (Besides slicing off SOG, the output from this pin gets
no other additional processing on the AD9980. Vsync separation is performed via the sync separator.)
O/E FIELD
Odd/Even Field Bit for Interlaced Video.
This output will identify whether the current field (in an interlaced signal) is odd or even.
SERIAL PORT
SDA
Serial Port Data I/O.
SCL
Serial Port Data Clock.
VSOUT/A0
Serial Port Address Input 0. Pin shared with VSOUT. This pin selects the LSB of the serial port device address,
allowing two Analog Devices parts to be on the same serial bus. A high impedance external pull-up resistor
enables this pin to be read at power-up as 1, or a high impedance, external pull-down resistor enables this pin to
be read at power-up as a 0 and not interfere with the VSOUT functionality. For more details on VSOUT, see the
Outputs section in this table.
DATA OUTPUTS
RED [7:0]
GREEN [7:0]
BLUE [7:0]
Data Output, Red Channel.
Data Output, Green Channel.
Data Output, Blue Channel.
The main data outputs. Bit 7 is the MSB. The delay from pixel sampling time to output is fixed. When the
sampling time is changed by adjusting the phase register, the output timing is shifted as well. The DATACK and
HSOUT outputs are also moved, so the timing relationship among the signals is maintained.
DATA CLOCK OUTPUT
DATACK
Data Clock Output. This is the main clock output signal used to strobe the output data and HSOUT into external
logic. Four possible output clocks can be selected with Register 0x20, Bits [7:6]. Three of these are related to the
pixel clock (pixel clock, 90° phase-shifted pixel clock, and 2× frequency pixel clock). They are produced either by
the internal PLL clock generator or EXTCLK and are synchronous with the pixel sampling clock. The fourth option
for the data clock output is an internally generated 40 MHz clock.
The sampling time of the internal pixel clock can be changed by adjusting the phase register (Register 0x04).
When this is changed, the pixel related DATACK timing is also shifted. The Data, DATACK, and HSOUT outputs
are all moved so that the timing relationship among the signals is maintained.
POWER SUPPLY
VD (3.3 V)
Main Power Supply. These pins supply power to the main elements of the circuit. They should be as quiet and
filtered as possible.
VDD (1.8 V to 3.3 V)
Digital Output Power Supply. A large number of output pins (up to 29) switching at high speed (up to 95 MHz)
generate a lot of power supply transients (noise). These supply pins are identified separately from the VD pins, so
special care can be taken to minimize output noise transferred into the sensitive analog circuitry. If the AD9980
is interfacing with lower voltage logic, VDD may be connected to a lower supply voltage (as low as 1.8 V) for
compatibility.
PVD (1.8 V)
Clock Generator Power Supply. The most sensitive portion of the AD9980 is the clock generation circuitry. These
pins provide power to the clock PLL and help the user design for optimal performance. The designer should
provide quiet, noise-free power to these pins.
DAVDD (1.8 V)
GND
Digital Input Power Supply. This supplies power to the digital logic.
Ground. The ground return for all circuitry on-chip. It is recommended that the AD9980 be assembled on a
single solid ground plane, with careful attention to ground current paths.
Rev. 0 | Page 9 of 44
AD9980
DESIGN GUIDE
slightly and providing a high quality signal over a wider range
of conditions. Using a Fair-Rite #2508051217Z0 high speed,
signal chip bead inductor in the circuit shown in Figure 3 gives
good results in most applications.
GENERAL DESCRIPTION
The AD9980 is a fully integrated solution for capturing analog
RGB or YPbPr signals and digitizing them for display on
advanced TVs, flat panel monitors, projectors, and other types
of digital displays. Implemented in a high-performance CMOS
process, the interface can capture signals with pixel rates of up
to 95 MHz.
47nF
R
AIN
RGB
G
B
AIN
INPUT
AIN
75Ω
The AD9980 includes all necessary input buffering, signal dc
restoration (clamping), offset and gain (brightness and contrast)
adjustment, pixel clock generation, sampling phase control, and
output data formatting. All controls are programmable via a
two-wire serial interface (I2C®). Full integration of these
sensitive analog functions makes system design straightforward
and less sensitive to the physical and electrical environment.
Figure 3. Analog Input Interface Circuit
HSYNC AND VSYNC INPUTS
The interface also accepts Hsync and vertical sync period
(Vsync) signals, which are used to generate the pixel clock,
clamp timing, Coast and field information. These can be either
a sync signal directly from the graphics source, or a
preprocessed TTL or CMOS level signal.
With a typical power dissipation of less than 900 mW and an
operating temperature range of 0°C to 70°C, the device requires
no special environmental considerations.
The Hsync input includes a Schmitt trigger buffer for immunity
to noise and signals with long rise times. In typical PC-based
graphic systems, the sync signals are simply TTL-level drivers
feeding unshielded wires in the monitor cable. As such, no
termination is required.
DIGITAL INPUTS
All digital inputs on the AD9980 operate to 3.3 V CMOS levels.
The following digital inputs are 5 V tolerant (Applying 5 V to
them does not cause any damage): HSYNC0, HSYNC1,
VSYNC0, VSYNC1, SOGIN0, SOGIN1, SDA, SCL and CLAMP.
SERIAL CONTROL PORT
The serial control port is designed for 3.3 V logic; however, it is
tolerant of 5 V logic signals.
INPUT SIGNAL HANDLING
OUTPUT SIGNAL HANDLING
The AD9980 has six high-impedance analog input pins for the
red, green, and blue channels. They accommodate signals
ranging from 0.5 V to 1.0 V p-p.
The digital outputs are designed to operate from 1.8 V to
3.3 V (VDD).
CLAMPING
Signals are typically brought onto the interface board with a
DVI-I connector, a 15-pin D connector, or RCA connectors.
The AD9980 should be located as close as possible to the input
connector. Signals should be routed using matched-impedance
traces (normally 75 Ω) to the IC input pins.
RGB Clamping
To properly digitize the incoming signal, the dc offset of the
input must be adjusted to fit the range of the on-board ADCs.
Most graphics systems produce RGB signals with black at
ground and white at approximately 0.75 V. However, if sync
signals are embedded in the graphics, the sync tip is often at
ground and black is at 300 mV. Then white is at approximately
1.0 V. Some common RGB line amplifier boxes use emitter-
follower buffers to split signals and increase drive capability.
This introduces a 700 mV dc offset to the signal, which must be
removed for proper capture by the AD9980.
At the input pins the signal should be resistively terminated
(75 Ω to the signal ground return) and capacitively coupled to
the AD9980 inputs through 47 nF capacitors. These capacitors
form part of the dc restoration circuit.
In an ideal world of perfectly matched impedances, the best
performance can be obtained with the widest possible signal
bandwidth. The wide bandwidth inputs of the AD9980
(200 MHz) can continuously track the input signal as it moves
from one pixel level to the next and can digitize the pixel during
a long, flat pixel time. In many systems, however, there are mis-
matches, reflections, and noise, which can result in excessive
ringing and distortion of the input waveform. This makes it
more difficult to establish a sampling phase that provides good
image quality. It has been shown that a small inductor in series
with the input is effective in rolling off the input bandwidth
The key to clamping is to identify a portion (time) of the signal
when the graphic system is known to be producing black. An
offset is then introduced that results in the ADCs producing a
black output (Code 0x00) when the known black input is
present. The offset then remains in place when other signal
levels are processed, and the entire signal is shifted to eliminate
offset errors.
Rev. 0 | Page 10 of 44
AD9980
In most PC graphics systems, black is transmitted between
active video lines. With CRT displays, when the electron beam
has completed writing a horizontal line on the screen (at the
right side), the beam is deflected quickly to the left side of the
screen (called horizontal retrace) and a black signal is provided
to prevent the beam from disturbing the image.
Clamping to midscale rather than ground can be accomplished
by setting the clamp select bits in the serial bus register. Each of
the three converters has its own selection bit so that they can be
independently clamped to either midscale or ground. These bits
are located in Register 0x18, Bits [3:1]. The midscale reference
voltage is internally generated for each converter.
In systems with embedded sync, a blacker-than-black signal
(Hsync) is produced briefly to signal the CRT that it is time to
begin a retrace. Because the input is not at black level at this
time, it is important to avoid clamping during Hsync.
Fortunately, there is virtually always a period following Hsync,
called the ‘back porch’, where a good black reference is provided.
This is the time when clamping should be done.
GAIN AND OFFSET CONTROL
The AD9980 contains three PGAs, one for each of the three
analog inputs. The range of the PGA is sufficient to accom-
modate input signals with inputs ranging from 0.5 V to 1.0 V
full scale. The gain is set in three 7-bit registers (red gain [0x05],
green gain [0x07], blue gain [0x09]). For each register, a gain
setting of 0 corresponds to the highest gain, while a gain setting
of 127 corresponds to the lowest gain. Note that increasing the
gain setting results in an image with less contrast.
The clamp timing can be established by simply exercising the
CLAMP pin at the appropriate time with clamp source
(Register 0x18, Bit 4) = 1. The polarity of this signal is set by
the clamp polarity bit (Register 0x1B, Bits [7:6]).
The offset control shifts the analog input, resulting in a change
in brightness. Three 9-bit registers (red offset [0x0B, 0x0C],
green offset [0x0D, 0x0E], blue offset [0x0F, 0x10]) provide
independent settings for each channel. The function of the
offset register depends on whether auto-offset is enabled
(Register 0x1B, Bit 5).
A simpler method of clamp timing uses the AD9980’s internal
clamp timing generator. The clamp placement register
(Register 0x19) is programmed with the number of pixel
periods that should pass after the trailing edge of Hsync before
clamping starts. A second register, clamp duration, (Register
0x1A) sets the duration of the clamp. These are both 8-bit
values, providing considerable flexibility in clamp generation.
The clamp timing is referenced to the trailing edge of Hsync
because, though Hsync duration can vary widely, the back porch
(black reference) always follows Hsync. A good starting point
for establishing clamping is to set the clamp placement to 0x04
(providing 4 pixel periods for the graphics signal to stabilize
after sync) and set the clamp duration to 0x28 (giving the clamp
40 pixel periods to reestablish the black reference).
If manual offset is used, seven bits of the offset registers (for the
red channel Register 0x0B, Bits [6:0] control the absolute offset
added to the channel. The offset control provides 63 LSBs of
adjustment range, with one LSB of offset corresponding to one
LSB of output code.
Automatic Offset
In addition to the manual offset adjustment mode, the AD9980
also includes circuitry to automatically calibrate the offset for
each channel. By monitoring the output of each ADC during
the back porch of the input signals, the AD9980 can self-adjust
to eliminate any offset errors in its own ADC channels and any
offset errors present on the incoming graphics or video signals.
Clamping is accomplished by placing an appropriate charge on
the external input coupling capacitor. The value of this capacitor
affects the performance of the clamp. If it is too small, there will
be a significant amplitude change during a horizontal line time
(between clamping intervals). If the capacitor is too large, then
it will take excessively long for the clamp to recover from a large
change in incoming signal offset. The recommended value
(47 nF) results in recovering from a step error of 100 mV to
within ½ LSB in 20 lines with a clamp duration of 20 pixel
periods on a 85 Hz XGA signal.
To activate the auto-offset mode, set Register 0x1B, Bit 5 to 1.
Next, the target code registers (0x0B through 0x10) must be
programmed. The values programmed into the target code
registers should be the output code desired from the AD9980
ADCs, which are generated during the back porch reference
time. For example, for RGB signals, all three registers are
normally programmed to Code 1, while for YPbPr signals the
green (Y) channel is normally programmed to Code 1 and the
blue and red channels (Pb and Pr) are normally set to 128. The
target code registers have nine bits per channel and are in twos
complement format. This allows any value between –256 and
+255 to be programmed. Although any value in this range can
be programmed, the AD9980’s offset range may not be able to
reach every value. Intended target code values range from (but
are not limited to) –40 to –1 and +1 to +40 when ground
clamping and +88 to +168 when midscale clamping. (Note that
a target code of 0 is not valid.)
YPbPr Clamping
YPbPr graphic signals are slightly different from RGB signals in
that the dc reference level (black level in RGB signals) for the
color difference signals is at the midpoint of the video signal
rather than at the bottom. The three inputs are composed of
luminance (Y) and color difference (Pb and Pr) signals. For the
color difference signals it is necessary to clamp to the midscale
range of the ADC range (128) rather than at the bottom of the
ADC range (0) while the Y channel is clamped to ground.
Rev. 0 | Page 11 of 44
AD9980
Negative target codes are included in order to duplicate a fea-
ture that is present with manual offset adjustment. The benefit
that is being mimicked is the ability to easily adjust brightness
on a display. By setting the target code to a value that does not
correspond to the ideal ADC range, the end result is an image
that is either brighter or darker. A target code higher than ideal
results in a brighter image while a target code lower than ideal
results in a darker image.
Sync-on-Green
The sync-on-green input operates in two steps. First, it sets a
baseline clamp level off of the incoming video signal with a
negative peak detector. Second, it sets the sync trigger level to
a programmable (Register 0x1D, Bits [7:3]) level (typically
128 mV) above the negative peak. The sync-on-green input
must be ac-coupled to the green analog input through its own
capacitor. The value of the capacitor must be 1 nF 20%. If
sync-on-green is not used, this connection is not required. The
sync-on-green signal always has negative polarity.
The ability to program a target code gives a large degree of
freedom and flexibility. While in most cases all channels will
be set to either 1 or 128, the flexibility to select other values
allows for the possibility of inserting intentional skews between
channels. It also allows the ADC range to be skewed so that
voltages outside of the normal range can be digitized. For
example, setting the target code to 40 allows the sync tip, which
is normally below black level, to be digitized and evaluated.
47nF
R
B
AIN
47nF
47nF
1nF
AIN
G
AIN
SOG
Figure 4. Typical Input Configuration
The internal logic for the auto-offset circuit requires 16 data
clock cycles to perform its function. This operation is executed
immediately after the clamping pulse. Therefore, it is important
to end the clamping pulse signal at least 16 data clock cycles
before active video. This is true whether using the AD9980’s
internal clamp circuit or an external clamp signal. The auto-
offset function can be programmed to run continuously or on a
one-time basis (see auto-offset hold, Register 0x2C, Bit 4). In
continuous mode, the update frequency can be programmed
(Register 0x1B, Bits [4:3]). Continuous operation with updates
every 64 Hsyncs is recommended.
Reference Bypassing
REFLO and REFHI are connected to each other through a
10 µF capacitor. REFCM is connected to ground through a
10 µF capacitor. These references are used by the input
PGA circuitry.
REFHI
10µF
REFLO
REFCM
10µF
A guideline for basic auto-offset operation is shown in Table 5
and Table 6.
Figure 5. Input Amplifier Reference Capacitors
Table 5. RGB Auto-Offset Register Settings
Clock Generation
Register
0x0B
0x0C
0x0D
0x0E
0x0F
0x10
0x18, Bits [3:1]
Value Comments
A PLL is employed to generate the pixel clock. The Hsync input
provides a reference frequency to the PLL. A voltage controlled
oscillator (VCO) generates a much higher pixel clock
frequency. This pixel clock is divided by the PLL divide value
(Register 0x01 and Register 0x02) and phase-compared with
the Hsync input. Any error is used to shift the VCO frequency
and maintain lock between the two signals.
0x02
0x00
0x02
0x00
0x02
0x00
000
Sets red target to 4
Must be written
Sets green target to 4
Must be written
Sets blue target to 4
Must be written
Sets red, green, and blue
channels to ground clamp
Selects update rate and
enables auto-offset.
0x1B, Bit [5:3]
110
The stability of this clock is a very important element in
providing the clearest and most stable image. During each pixel
time, there is a period during which the signal is slewing from
the old pixel amplitude and settling at its new value. Then there
is a time when the input voltage is stable, before the signal must
slew to a new value (see Figure 6). The ratio of the slewing time
to the stable time is a function of the bandwidth of the graphics
DAC and the bandwidth of the transmission system (cable and
termination). It is also a function of the overall pixel rate.
Clearly, if the dynamic characteristics of the system remain
fixed, then the slewing and settling time is likewise fixed. This
time must be subtracted from the total pixel period, leaving the
stable period. At higher pixel frequencies, the total cycle time is
shorter and the stable pixel time also becomes shorter.
Table 6. PbPr Auto-Offset Register Settings
Register
0x0B
0x0C
0x0D
0x0E
0x0F
0x10
Value Comments
0x40
0x00
0x02
0x00
0x40
0x00
101
Sets Pr (red) target to 128
Must be written
Sets Y (green) target to 4
Must be written
Sets Pb (blue) target to 128
Must be written
Sets Pb, Pr to midscale clamp
and Y to ground clamp
Selects update rate and
enables auto-offset
0x18 Bits [3:1]
0x1B, Bit [5:3]
110
Rev. 0 | Page 12 of 44
AD9980
PIXEL CLOCK
INVALID SAMPLE TIMES
range register sets this operating range. The frequency
ranges for the four regions are shown in Table 7.
Table 7. VCO Frequency Ranges
Pixel Clock
PV1 PV0 Range (MHz)
KVCO
Gain (MHz/V)
0
0
1
1
0
1
0
1
10 to 21
21 to 42
42 to 84
84 to 95
150
150
150
150
Figure 6. Pixel Sampling Times
3. The 3-bit Charge Pump Current Register. This register
varies the current that drives the low-pass loop filter. The
possible current values are listed in Table 8.
Any jitter in the clock reduces the precision with which the
sampling time can be determined and must also be subtracted
from the stable pixel time. Considerable care has been taken in
the design of the AD9980’s clock generation circuit to minimize
jitter. The clock jitter of the AD9980 is 9% or less of the total
pixel time in all operating modes, making the reduction in the
valid sampling time due to jitter negligible.
Table 8. Charge Pump Current/Control Bits
Ip2
Ip1
Ip0
Current (µA)
0
0
0
50
0
0
1
100
0
0
1
1
1
1
1
1
0
0
1
1
0
1
0
1
0
1
150
250
350
500
750
1500
The PLL characteristics are determined by the loop filter design,
the PLL Charge Pump Current, and the VCO range setting. The
loop filter design is illustrated in Figure 7. Recommended
settings of VCO range and charge pump current for VESA
standard display modes are listed in Table 9.
PV
D
C
C
Z
P
8nF
80nF
R
Z
4. The 5-bit Phase Adjust Register. The phase of the generated
sampling clock may be shifted to locate an optimum samp-
ling point within a clock cycle. The phase adjust register
provides 32 phase-shift steps of 11.25° each. The Hsync
signal with an identical phase shift is available through the
HSOUT pin. Phase adjust is still available if an external
pixel clock is used. The COAST pin or internal Coast is
used to allow the PLL to continue to run at the same
frequency in the absence of the incoming Hsync signal or
during disturbances in Hsync (such as from equalization
pulses). This may be used during the vertical sync period
or at any other time that the Hsync signal is unavailable.
The polarity of the Coast signal may be set through the
Coast polarity register (Register 0x18, Bits [6:5]). Also, the
polarity of the Hsync signal may be set through the Hsync
polarity register (Register 0x12, Bits [5:4]). For both Hsync
and Coast, a value of 1 is active high. The internal Coast
function is driven off of the Vsync signal, which is typically
a time when Hsync signals may be disrupted with extra
equalization pulses.
1.5kΩ
FILT
Figure 7. PLL Loop Filter Detail
Four programmable registers are provided to optimize the
performance of the PLL. These registers are
1. The 12-Bit Divisor Register. The input Hsync frequencies
can accommodate any Hsync as long as the product of the
Hsync and the PLL divisor falls within the operating range
of the VCO. The PLL multiplies the frequency of the Hsync
signal, producing pixel clock frequencies in the range of
10 MHz to 95 MHz. The divisor register controls the exact
multiplication factor. This register may be set to any value
between 2 and 4095 as long as the output frequency is
within range.
2. The 2-Bit VCO Range Register. To improve the noise
performance of the AD9980, the VCO operating frequency
range is divided into four overlapping regions. The VCO
Rev. 0 | Page 13 of 44
AD9980
Table 9. Recommended VCO Range and Charge Pump and Current Settings for Standard Display Formats
Refresh Rate
Standard Resolution (Hz)
Horizontal Frequency
(kHz)
Pixel Rate
(MHZ)
PLL
Divider
VCORNGE Current
VGA
640 × 480
60
72
75
85
56
60
72
75
85
31.500
37.700
37.500
43.300
35.100
37.900
48.100
46.900
53.700
48.400
56.500
60.000
64.000
68.300
15.750
31.470
15.625
31.250
45.000
33.750
33.750
25.175
31.500
31.500
36.000
36.000
40.000
50.000
49.500
56.250
65.000
75.000
78.750
85.500
94.500
13.510
27.000
13.500
27.000
74.250
74.250
74.250
800
01
01
01
01
01
01
10
10
10
10
10
10
11
11
00
01
00
01
10
10
10
100
100
100
101
101
100
100
100
100
101
110
110
100
100
100
100
100
100
101
101
101
832
840
832
SVGA
800 × 600
1024
1056
1040
1056
1048
1344
1328
1312
1336
1376
858
XGA
1024 × 768 60
70
75
80
85
TV
480i
30
60
30
60
60
30
60
480p
576i
858
864
576p
720p
1035i
1080i
864
1650
2200
2200
Rev. 0 | Page 14 of 44
AD9980
CHANNEL
SELECT
HSYNC
SELECT
HSYNC0
HSYNC1
SOGIN0
SOGIN1
VSYNC0
VSYNC1
ACTIVITY
DETECT
POLARITY
DETECT
MUX
HSYNC FILTER
AND
REGENERATOR
MUX
FILTERED
HSYNC
REGENERATED
HSYNC
ACTIVITY
DETECT
POLARITY
DETECT
SYNC
SLICER
ACTIVITY
DETECT
MUX
MUX
SET POLARITY
SOGOUT
SYNC
SLICER
ACTIVITY
DETECT
SYNC
PROCESSOR
AND
VSYNC FILTER
ACTIVITY
DETECT
POLARITY
DETECT
MUX
VSYNCOUT
ACTIVITY
DETECT
POLARITY
DETECT
HSYNC/VSYNC
COUNTER
REG 26H, 27H
ODD/EVEN
FIELD
SET POLARITY
HSYNC
SET POLARITY
SET POLARITY
VSYNCOUT
DATACK
COAST
PLL CLOCK
GENERATOR
MUX
COAST
AD9980
Figure 8. Sync Processing Block Diagram
Sync Processing
jitter, Hsync signal that can be used for mode detection and
counting Hsyncs per Vsync. The Vsync filter is used to elimi-
nate spurious Vsyncs, maintain a stable timing relationship
between the Vsync and Hsync output signals, and generate the
odd/even field output. The Coast generator creates a robust
Coast signal that allows the PLL to maintain its frequency in
the absence of Hsync pulses.
The inputs of the sync processing section of the AD9980 are
combinations of digital Hsyncs and Vsyncs, analog sync-on-
green, or sync-on-Y signals, and an optional external Coast
signal. From these signals it generates a precise, jitter-free (9%
or less at 95 MHz) clock from its PLL; an odd-/even-field signal;
Hsync and Vsync out signals; a count of Hsyncs per Vsync; and
a programmable SOG output. The main sync processing blocks
are the sync slicer, sync separator, Hsync filter, Hsync regen-
erator, Vsync filter, and Coast generator.
Sync Slicer
The purpose of the sync slicer is to extract the sync signal from
the green graphics or luminance video signal that is connected
to the SOGIN input. The sync signal is extracted in a two step
process. First, the SOG input is clamped to its negative peak,
(typically 0.3 V below the black level). Next, the signal goes to a
comparator with a variable trigger level (set by Register 0x1D,
Bits [7:3]), but nominally 0.128 V above the clamped level. The
sync slicer output is a digital composite sync signal containing
both Hsync and Vsync information (see Figure 9).
The sync slicer extracts the sync signal from the green graphics
or luminance video signal that is connected to the SOGIN input
and outputs a digital composite sync. The sync separator’s task
is to extract Vsync from the composite sync signal, which can
come from either the sync slicer or the Hsync input. The Hsync
filter is used to eliminate any extraneous pulses from the Hsync
or SOGIN inputs, outputting a clean, low-jitter signal that is
appropriate for mode detection and clock generation. The
Hsync regenerator is used to recreate a clean, although not low
Rev. 0 | Page 15 of 44
AD9980
Preliminary Technical Data
NEGATIVE PULSE WIDTH = 40 SAMPLE CLOCKS
700mV MAXIMUM
–300mV
SOG INPUT
0mV
–300mV
SOGOUT OUTPUT
CONNECTED TO
HSYNCIN
COMPOSITE
SYNC
AT HSYNCIN
VSYNCOUT
FROM SYNC
SEPARATOR
Figure 9. Sync Slicer and Sync Separator Output
Sync Separator
counting Hsyncs per Vsync. The Hsync regenerator has a high
degree of tolerance to extraneous and missing pulses on the
Hsync input, but is not appropriate for use by the PLL in
creating the pixel clock due to jitter.
As part of sync processing, the sync separator’s task is to extract
Vsync from the composite sync signal. It works on the idea that
the Vsync signal stays active for a much longer time than the
Hsync signal. By using a digital low-pass filter and a digital
comparator, it rejects pulses with small durations (such as
Hsyncs and equalization pulses) and only passes pulses with
large durations, such as Vsync (see Figure 9).
The Hsync regenerator runs automatically and requires no
setup to operate. The Hsync filter requires the setting up of a
filter window. The filter window sets a periodic window of time
around the regenerated Hsync leading edge where valid Hsyncs
are allowed to occur. The general idea is that extraneous pulses
on the sync input will occur outside of this filter window and
thus will be filtered out. In order to set the filter window timing,
program a value (x) into Register 0x23. The resulting filter
window time is x times 25 ns around the regenerated Hsync
leading edge. Just as for the sync separator threshold multiplier,
allow a 20% variance in the 25 ns multiplier to account for all
operating conditions (20 nS to 30 ns range).
The threshold of the digital comparator is programmable for
maximum flexibility. To program the threshold duration, write a
value (N) to Register 0x11. The resulting pulse width will be
N × 200 ns. So, if N = 5 the digital comparator threshold will be
1 µs. Any pulses less than 1 µs are rejected, while any pulse
greater than 1 µs passes through.
There are two things to keep in mind when using the sync
separator. First, the resulting clean Vsync output will be delayed
from the original Vsync by a duration equal to the digital
comparator threshold (N × 200 ns). Second, there is some
variability to the 200 ns multiplier value. The maximum varia-
bility over all operating conditions will be 20% (160 ns to
240 ns). Since normal Vsync and Hsync pulse widths differ by a
factor of about 500 or more, the 20% variability is not an issue.
A second output from the Hsync filter is a status bit (Reg-
ister 0x25, Bit 1) that tells whether extraneous pulses are present
on the incoming sync signal. Extraneous pulses are often
included for copy protection purposes; this status bit can be
used to detect that.
The filtered Hsync (rather than the raw Hsync/SOGIN signal)
for pixel clock generation by the PLL is controlled by Reg-
ister 0x20, Bit 2. The regenerated Hsync (rather than the raw
Hsync/ SOGIN signal) for the sync processing is controlled by
Register 0x20, Bit 1. Use of the filtered Hsync and regenerated
Hsync is recommended. See Figure 10 for an illustration of a
filtered Hsync.
Hsync Filter and Regenerator
The Hsync filter is used to eliminate any extraneous pulses from
the Hsync or SOGIN inputs, outputting a clean, low-jitter signal
that is appropriate for mode detection and clock generation.
The Hsync regenerator is used to recreate a clean, although not
low jitter, Hsync signal that can be used for mode detection and
Rev. 0 | Page 16 of 44
AD9980
HSYNCIN
FILTER
WINDOW
HSYNCOUT
VSYNC
EQUALIZATION
PULSES
EXPECTED
EDGE
FILTER
WINDOW
Figure 10. Sync Processing Filter
Vsync Filter and Odd/Even Fields
SYNC SEPARATOR THRESHOLD
The Vsync filter is used to eliminate spurious Vsyncs, maintain
a stable timing relationship between the Vsync and Hsync
output signals, and generate the odd/even field output.
FIELD 1
2
FIELD 0
FIELD 1
FIELD 0
QUADRANT
HSYNCIN
3
4
1
2
3
4
1
The filter works by examining the placement of Vsync with
respect to Hsync, and if necessary, slightly shifting it in time.
The goal is to keep the Vsync and Hsync leading edges from
switching at the same time, eliminating confusion as to when
the first line of a frame occurs. Enable the Vsync filter with
Register 0x14, Bit 2. Use of the Vsync filter is recom-mended for
all cases, including interlaced video, and is required when using
the Hsync per Vsync counter. Figure 12 illustrates even/odd
field determination in two situations.
VSYNCIN
VSYNCOUT
O/E FIELD
ODD FIELD
Figure 11.
Rev. 0 | Page 17 of 44
AD9980
Preliminary Technical Data
SYNC SEPARATOR THRESHOLD
the power-down pin must be set (0x1E, Bit 2) regardless of
whether the pin is used. If unused, it is recommended to set the
polarity to active high and hardwire the pin to ground with a
10 kΩ resistor.
FIELD 1
FIELD 0
FIELD 1
FIELD 0
QUADRANT
HSYNCIN
2
3
4
1
2
3
4
1
In power-down mode, there are several circuits that continue to
operate normally. The serial register and sync detect circuits
maintain power so that the AD9980 can be woken up from
its power-down state. The bandgap circuit maintains power
because it is needed for sync detection. The sync-on-green and
SOGOUT functions continue to operate because the SOGOUT
output is needed when sync detection is performed by a
secondary chip. All of these circuits require minimal power to
operate. Typical standby power on the AD9980 is about 50 mW.
VSYNCIN
VSYNCOUT
O/E FIELD
EVEN FIELD
Figure 12. Vsync Filter—Odd/Even
Power Management
To meet display requirements for low standby power, the
There are two options that can be selected when in power-
down. These are controlled by Bits 0 and 1 in Register 0x1E. The
first is to determine whether the SOGOUT pin is put in high
impedance or not. In most cases, SOGOUT is not put in high
impedance during normal operation. The option to put
SOGOUT in high impedance is included mainly to allow for
factory testing modes. The second option is to keep the AD9980
powered up and only put the outputs in high impedance. This
option is useful when the data outputs from two chips are
connected on a PCB and the user wants to switch
AD9980 includes a power-down mode. The power-down state
can be controlled manually (with Pin 17 or Register 0x1E, Bit 3),
or completely automatically by the chip. If automatic control is
selected (0x1E, Bit 4), the AD9980’s decision is based on the
status of the sync detect bits (Register 0x24, Bits 2, 3, 6,
and 7). If either an Hsync or a sync-on-green input is detected
on any input, the chip powers up, otherwise it powers down. If
manual control is desired, the AD9980 includes the flexibility of
control with both a dedicated pin and a register bit. The dedi-
cated pin allows a hardware watchdog circuit to control power-
down, while the register bit allows power-down to be controlled
by software. With manual power-down control, the polarity of
instantaneously between the two.
Table 10.Power-Down Control and Mode Descriptions
Inputs
Auto Power-Down
Control1
Power-Down2
Sync Detect3
Powered-On or Comments
Mode
Power-Up
Power-Down
1
1
X
X
1
0
Everything
Only the serial bus, sync activity detect,
SOG, bandgap reference
Power-Up
Power-Down
0
0
0
1
X
X
Everything
Only the serial bus, sync activity detect,
SOG, bandgap reference
1 Auto power-down control is set by Register 0x1E, Bit 4.
2 Power-down is controlled by OR’ing Pin 17 with Register 0x1E, Bit 3. The polarity of Pin 17 is set by Register 0x1E, Bit 2.
3 Sync detect is determined by OR’ing Register 0x24, Bits 2, 3, 6, and 7.
Rev. 0 | Page 18 of 44
AD9980
latch the output data externally. There is a pipeline in the
TIMING DIAGRAMS
AD9980, which must be flushed before valid data becomes
available. This means six data sets are presented before valid
data is available.
The following timing diagrams show the operation of the
AD9980.The output data clock signal is created so that its rising
edge always occurs between data transitions and can be used to
tPER
tDCYCLE
DATACK
+tSKEW
–tSKEW
DATA
HSOUT
Figure 13. Output Timing
DATAIN
HSIN
P0
P1
P2
P5
P6
P9
P3
P4
P7
P8
P10
P11
DATACLK
8 CLOCK CYCLE DELAY
P0 P1 P2
DATAOUT
HSOUT
P3
2 CLOCK CYCLE DELAY
Figure 14. 4:4:4 Timing Mode
DATAIN
HSIN
P0
P1
P2
P5
P6
P9
P3
P4
P7
P8
P10
P11
DATACLK
8 CLOCK CYCLE DELAY
YOUT
Y0
Y1
Y2
Y3
R2
CB/CROUT
B0
R0
B2
2 CLOCK CYCLE DELAY
HSOUT
1. PIXEL AFTER HSOUT CORRESONDS TO BLUE INPUT.
2. EVEN NUMBER OF PIXEL DELAY BETWEEN HSOUT AND DATAOUT (6 FOR THE AD9980).
Figure 15. 4:2:2 Timing Mode
Rev. 0 | Page 19 of 44
AD9980
Preliminary Technical Data
DATAIN
HSIN
P0
P1
P2
P5
P6
P9
P3
P4
P7
P8
P10
P11
DATACLK
8 CLOCK CYCLE DELAY
F0 R0 F1 R1 F2 R2 F3 R3
2 CLOCK CYCLE DELAY
HSOUT
DDR NOTES
1. OUTPUT DATACLK MAY BE DELAYED 1/4 CLOCK PERIOD IN THE REGISTERS.
2. FOR DDR 4:2:2 MODE: TIMING IS IDENTICAL, VALUES OF F (FALLING EDGE) AND R (RISING EDGE) CHANGE.
GENERAL NOTES
1. DATA DELAY MAY VARY ± ONE CLOCK CYCLE, DEPENDING ON PHASE SETTING.
2. ADCs SAMPLE INPUT ON FALLING EDGE OF DATACLK.
3. HSYNC SHOWN IS ACTIVE HIGH (EDGE SHOWN IS LEADING EDGE).
Figure 16. DDR Timing Mode
The Coast input is provided to eliminate this problem. It is an
HSYNC TIMING
asynchronous input that disables the PLL input and holds the
clock at its current frequency. The PLL can run free for several
lines without significant frequency drift. Coast can be generated
internally by the AD9980 (see Register 0x18) or can be provided
externally by the graphics controller.
The Hsync is processed in the AD9980 to eliminate ambiguity
in the timing of the leading edge with respect to the phase-
delayed pixel clock and data.
The Hsync input is used as a reference to generate the pixel
sampling clock. The sampling phase can be adjusted with
respect to Hsync through a full 360° in 32 steps via the phase
adjust register (to optimize the pixel sampling time). Display
systems use Hsync to align memory and display write cycles, so
it is important to have a stable timing relationship between
Hsync output (HSOUT) and the data clock (DATACK).
When internal Coast is selected (Register 0x18, Bit 7 = 0, and
Register 0x14, Bits [7:6] to select source), the Vsync is used as
the basis for determining the position of Coast. The internal
Coast signal is enabled a programmed number of Hsync
periods before the periodic Vsync signal (Precoast
Register 0x16) and dropped a programmed number of Hsync
periods after the Vsync (Postcoast Register 0x17). It is
recommended that the Vsync filter be enabled when using the
internal Coast function to allow the AD9980 to precisely
determine the number of Hsyncs/Vsync and their location. In
many applications where disruptions occur and Coast is used,
values of 2 for the Precoast and 10 for Postcoast are sufficient to
avoid most extraneous pulses.
Three things happen to Hsync in the AD9980. First, the polarity
of Hsync input is determined and thus has a known output
polarity. The known output polarity can be programmed either
active high or active low (Register 0x12, Bit 3). Second, HSOUT
is aligned with DATACK and data outputs. Third, the duration
of HSOUT (in pixel clocks) is set via Register 0x13. HSOUT is
the sync signal that should be used to drive the rest of the
display system.
OUTPUT FORMATTER
COAST TIMING
The output formatter is capable of generating several output
formats to be presented to the 24 data output pins. The output
formats and the pin assignments for each format are listed in
Table 11. Also, there are several clock options for the output
clock. The user may select the pixel clock, a 90° phase-shifted
pixel clock, a 2× pixel clock, or a fixed frequency 40 MHz clock
for test purposes. The output clock may also be inverted.
In most computer systems, the Hsync signal is continuously
provided on a dedicated wire. In these systems, the Coast input
and function are unnecessary and should not be used.
In some systems, however, Hsync is disturbed during Vsync. In
some cases, Hsync pulses disappear. In other systems, such as
those that employ composite sync (Csync) signals or embedded
sync-on-green, Hsync may include equalization pulses or other
distortions during Vsync. To avoid upsetting the clock generator
during Vsync, it is important to ignore these distortions. If the
pixel clock PLL sees extraneous pulses, it attempts to lock to this
new frequency, and will change frequency by the end of the
Vsync period. It then takes a few lines of correct Hsync timing
to recover at the beginning of a new frame, resulting in a tearing
of the image at the top of the display.
Data output is available as a 24-pin RGB or YCbCr, or if either
4:2:2 or 4:4:4 DDR is selected, a secondary channel is available.
This secondary channel is always 4:2:2 DDR and allows the
flexibility of having a second channel with the same video data
that can be utilized by another display or a storage device.
Depending on the choice of output modes, the primary output
can be 24 pins, 16 pins or as few as 12 pins.
Rev. 0 | Page 20 of 44
AD9980
Mode Descriptions
•
4:4:4 DDR—This mode puts out full 4:4:4 data on 12 bits of
the red and green channels thus saving 12 pins. The first
half (RGB [11:0]) of the 24-bit data is sent on the rising
edge and the second half (RGB [23:12]) is sent on the
falling edge. The 4:2:2 DDR data is sent on the blue
channel, as in 4:2:2 mode.
•
4:4:4—All channels come out with their 8 data bits at the
same time. Data is aligned to the negative edge of the clock
for easy capture. This is the normal 24-bit output mode for
RGB or 4:4:4 YCbCr.
•
4:2:2—Red and green channels contain 4:2:2 formatted
data (16 pins) with Y data on the green channel and Cb, Cr
data on the red channel. Data is aligned to the negative
edge of the clock. The blue channel contains the secondary
channel with Cb, Y, Cr, Y formatted DDR 4:2:2 data. The
data edges are aligned to both edges of the pixel clock, so
use of the 90° clock may be necessary to capture the
DDR data.
RGB [23:0] = R [7:0] + G [7:0] + B [7:0], so RGB [23:12] =
R [7:0] + G [7:4] and RGB [11:0] = G [3:0] + B [7:0]
Table 11. Output Formats
Port
Red
Green
Blue
Bit
7
6
5
4
3
2
1
0
7
6
5
4
3
Green/Y
Y
2
1
0
7
6
5
4
3
2
1
0
4:4:4
4:2:21
Red/Cr
Cb, Cr
Blue/Cb
DDR 4:2:2 ↑ Cb, Cr ↓ Y, Y
DDR 4:2:2 ↑ Cb, Cr
DDR 4:2:2 ↓ Y, Y
DDR ↑2 G [3:0]
DDR ↑ B [7:4]
DDR ↑ B [3:0]
DDR ↓ G [7:4]
4:4:4 DDR
N/A
N/A
DDR ↓
2
R [7:0]
1 For 4:2:2 modes the first item in the list is the first pixel after Hsync.
2 Arrows in the table indicate clock edge. Rising edge of clock = ↑, falling edge = ↓.
Rev. 0 | Page 21 of 44
AD9980
Preliminary Technical Data
TWO-WIRE SERIAL REGISTER MAP
The AD9980 is initialized and controlled by a set of registers, which determine the operating modes. An external controller is employed to
write and read the control registers through the two-wire serial interface port.
Table 12. Control Register Map
Read and
Hexadecimal Write or
Default
Bits Value
Register
Name
Address
Read Only
Description
0x00
RO
7:0
Chip Revision
PLL Div MSB
An 8-bit register that represents the silicon revision level.
0x01
R/W
7:0
0110 1001
This register is for Bits [11:4] of the PLL divider. Larger values mean
the PLL operates at a faster rate. This register should be loaded first
whenever a change is needed. (This will give the PLL more time to
lock).1
0x02
0x03
R/W
R/W
7:4
7:6
5:3
1101 ****
01** ****
**00 1***
PLL Div LSB
VCO/CPMP
Bits [7:4] LSBs of the PLL divider word. Links to the PLL Div MSB to
make a 12-bit register.
1
Bits [7:6] VCO Range. Selects VCO frequency range.
(See PLL description).
Bits [5:3] Charge Pump Current. Varies the current that drives the
low-pass filter. (See PLL description).
2
**** *0**
Bit 2. External Clock Enable
0x04
0x05
R/W
R/W
7:3
1000 0***
Phase Adjust
Red Gain MSB
ADC clock phase adjustment. Larger values mean more delay.
(1 LSB = T/32).
6:0
*100 0000
7-Bit Red Channel Gain Control. Controls the ADC input range
(contrast) of each respective channel. Bigger values give less
contrast.2
0x06
0x07
R/W
R/W
7:0
6:0
0000 0000
*100 0000
Must be written to 0x00 following a write of Register 0x05 for
proper operation.
Green Gain
MSB
7-Bit Green Channel Gain Control. Controls the ADC input range
(contrast) of each respective channel. Bigger values give less
contrast.
2
0x08
0x09
R/W
R/W
7:0
6:0
0000 0000
*100 0000
Must be written to 0x00 following a write of Register 0x07 for
proper operation.
Blue Gain MSB
7-Bit Blue Channel Gain Control. Controls the ADC input range
(contrast) of each respective channel. Bigger values give less
contrast.
2
0x0A
0x0B
R/W
R/W
7:0
7:0
0000 0000
0100 0000
Must be written to 0x00 following a write of Register 0x09 for
proper operation.
Red Offset MSB 8-Bit MSB of the Red Channel Offset Control. Controls the dc offset
(brightness) of each respective channel. Bigger values decrease
brightness.
1
0x0C
0x0D
R/W
R/W
7
0*** ****
Red Offset
Linked with 0x0B to form the 9-bit red offset that controls the dc
offset (brightness) of the red channel in auto-offset mode.
7:0
0100 0000
Green Offset
MSB
8-Bit MSB of the Green Channel Offset Control. Controls the dc
offset (brightness) of each respective channel. Bigger values
decrease brightness.
1
0x0E
0x0F
R/W
R/W
7
0*** ****
Green Offset
Linked with 0x0D to form the 9-bit green offset that controls the
dc offset (brightness) of the green channel in auto-offset mode.
7:0
0100 0000
Blue Offset
MSB
8-Bit MSB of the Red Channel Offset Control. Controls the dc offset
(brightness) of each respective channel. Bigger values decrease
brightness.
1
0x10
0x11
R/W
R/W
7
0*** ****
Blue Offset
Linked with 0x0F to form the 9-bit blue offset that controls the dc
offset (brightness) of the blue channel in auto-offset mode.
7:0
0010 0000
Sync Separator This register sets the threshold of the sync separator’s digital
Threshold comparator.
Rev. 0 | Page 22 of 44
AD9980
Read and
Hexadecimal Write or
Default
Bits Value
Register
Name
Address
Read Only
Description
0x12
R/W
7
0*** ****
Hsync Control
Active Hsync Override.
0 = The chip determines the active Hsync source.
1 = The active Hsync Source is set by 0x12, Bit 6.
6
*0** ****
Selects the source of the Hsync for PLL and sync processing. This
bit is used only if 0x12, Bit 7 is set to 1 or if both syncs are active.
0 = Hsync is from Hsync input pin.
1 = Hsync is from SOG.
5
**0* ****
Hsync Polarity Override.
0 = The chip selects the Hsync input polarity.
1 = The polarity of the input Hsync is controlled by 0x12, Bit 4.
This applies to both Hsync0 and Hsync1.
4
3
***1 ****
**** 1***
Hsync input polarity: this bit is used only if 0x12, Bit 5 is set to 1.
0 = Active low input Hsync.
1 = Active high input Hsync.
Sets the polarity of the Hsync output signal.
0 = Active low Hsync output.
1 = Active high Hsync output.
0x13
0x14
R/W
R/W
7:0
7
0010 0000
0*** ****
Hsync
Duration
Sets the number of pixel clocks that Hsync out is active.
Vsync Control
Active Vsync Override.
0 = The chip determines the active Vsync source.
1 = The active Vsync source is set by 0x14, Bit 6.
6
5
*0** ****
**0* ****
Selects the source of Vsync for the sync processing. This bit is used
only if 0x14, Bit 7 is set to 1.
0 = Vsync is from the Vsync input pin.
1 = Vsync is from the sync separator.
Vsync Polarity Override.
0 = The chip selects the input Vsync polarity.
1 = The polarity of the input Vsync is set by 0x14, Bit 4.
This applies to both Vsync0 and Vsync1.
4
3
2
1
***1 ****
**** 1***
**** *0**
**** **0*
Vsync input polarity: this bit is used only if 0x14, Bit 5 is set to 1.
0 = Active low input Vsync.
1 = Active high input Vsync.
Sets the polarity of the output Vsync signal.
0 = Active low output Vsync.
1 = Active high output Vsync.
0 = The Vsync filter is disabled.
1 = The Vsync filter is enabled.
This needs to be enabled when using the Hsync to Vsync counter.
Enables the Vsync duration block. This is designed to be used with
the Vsync filter.
0 = Vsync output duration is unchanged.
1 = Vsync output duration is set by Register 0x15.
0x15
R/W
7:0
0000 1010
Vsync Duration Sets the number of Hsyncs that Vsync out is active. This is only
used if 0x14, Bit 1 is set to 1.
0x16
0x17
0x18
R/W
R/W
R/W
7:0
7:0
7
0000 0000
0000 0000
0*** ****
Precoast
The number of Hsync periods to Coast prior to Vsync.
The number of Hsync periods to Coast after Vsync.
Postcoast
Coast and
Coast Source.
Clamp Control
Selects the source of the Coast signal.
0 = Using internal Coast generated from Vsync.
1 = Using external Coast signal from external COAST pin.
6
*0** ****
Coast Polarity Override.
0 = The chip selects the external Coast polarity.
1 = The polarity of the external Coast signal is set by 0x18, Bit 5.
Rev. 0 | Page 23 of 44
AD9980
Preliminary Technical Data
Read and
Hexadecimal Write or
Default
Bits Value
Register
Name
Address
Read Only
Description
5
**1* ****
Coast Input Polarity.
This bit is used only if 0x18, Bit 6 is set to 1.
0 = Active low external Coast.
1 = Active high external Coast.
4
3
2
1
***0 ****
**** 0***
**** *0**
**** **0*
Clamp Source Select.
0 = Use the internal clamp generated from Hsync.
1 = Use the external clamp signal.
Red Clamp.
0 = Clamp the red channel to ground.
1 = Clamp the red channel to midscale.
Green Clamp.
0 = Clamp the green channel to ground.
1 = Clamp the green channel to midscale.
Blue Clamp.
0 = Clamp the blue channel to ground.
1 = Clamp the blue channel to midscale.
0
**** ***0
Must be set to 0 for proper operation.
0x19
0x1A
0x1B
R/W
R/W
R/W
7:0
0000 1000
Clamp
Placement
Places the clamp signal an integer of clock periods after the trailing
edge of the Hsync signal.
7:0
7
0010 0000
0*** ****
Clamp
Duration
Number of clock periods that the clamp signal is actively clamping.
Clamp and
Offset
External clamp polarity override.
0 = The chip selects the clamp polarity.
1 = The polarity of the clamp signal is set by 0x1B, Bit 6.
6
*1** ****
External Clamp Input Polarity. This bit is used only if 0x1B, Bit 7 is
set to 1.
0 = Active low external clamp.
1 = Active high external clamp.
5
**0* ****
***1 1***
0 = Auto-offset is disabled.
1 = Auto-offset is enabled (offsets become the desired clamp
code).
This selects how often the auto-offset circuit operates. 00 = every
clamp; 01 = 16 clamps; 10 = every 64 clamps; 11 = every Vsync.
4:3
2:0
7:0
7:3
**** *011
1111 1111
0111 1***
Must be written to default (011) for proper operation.
Must be set to 0xFF for proper operation.
0x1C
0x1D
R/W
R/W
TestReg0
SOG Control
SOG slicer threshold. Sets the voltage level of the SOG slicer’s
comparator.
2
**** *0**
SOGOUT Polarity.
Sets the polarity of the signal on the SOGOUT pin.
0 = Active low SOGOUT.
1 = Active high SOGOUT.
1:0
**** **00
SOGOUT Select.
00 = Raw SOG from sync slicer (SOG0 or SOG1).
01 = Raw Hsync (Hsync0 or Hsync1).
10 = Regenerated sync from sync filter.
11 = Filtered sync from sync filter.
0x1E
R/W
7
6
*** ****
Power
Channel Select Override.
0 = The chip determines which input channels to use.
1 = The input channel selection is determined by 0x1E, Bit 6.
*0** ****
Channel Select.
Input channel select: this is used only if 0x1E, Bit 7 is set to 1, or if
syncs are present on both channels.
0 = Channel 0 syncs and data are selected.
1 = Channel 1 syncs and data are selected.
Rev. 0 | Page 24 of 44
AD9980
Read and
Hexadecimal Write or
Default
Bits Value
Register
Name
Address
Read Only
Description
5
4
3
2
1
**1* ****
***1 ****
**** 0***
**** *0**
**** **0*
Programmable Bandwidth.
0 = Low analog input bandwidth.
1 = High analog input bandwidth.
Power-Down Control Select.
0 = Manual power-down control.
1 = Auto power-down control.
Power-Down.
0 = Normal operation.
1 = Power-down.
Power-Down Pin Polarity.
0 = Active low.
1 = Active high.
Power-Down Fast Switching Control.
0 = Normal power-down operation.
1 = The chip stays powered up and the outputs are put in high
impedance mode.
0
**** ***0
*00* ****
SOGOUT High Impedance Control.
0 = SOGOUT operates as normal during power-down.
1 = SOGOUT is in high impedance during power-down.
0x1F
R/W
6:5
Output
Select 1
Output Mode.
00 = 4:4:4 output mode.
01 = 4:2:2 output mode.
10 = 4:4:4 – DDR output mode.
4
***1 ****
**** 0***
**** *10*
Primary Output Enable.
0 = Primary output is in high impedance state.
1 = Primary output is enabled.
Secondary Output Enable.
0 = Secondary output is in high impedance state.
1 = Secondary output is enabled.
3
2:1
Output Drive Strength.
00 = Low output drive strength.
01 = Medium low output drive strength.
10 = Medium high output drive strength.
11 = High output drive strength.
Applies to all outputs except VSOUT.
0
**** ***0
00** ****
Output Clock Invert.
0 = Noninverted Pixel Clock.
1 = Inverted Pixel Clock.
Applies to all clocks output on DATACK.
0x20
R/W
7:6
Output
Select 2
Output Clock Select.
00 = Pixel clock.
01 = 90° phase shifted pixel clock.
10 = 2× pixel clock.
11 = 40 MHz internal clock.
5
4
3
**0* ****
***0 ****
**** 1***
Output High Impedance.
0 = Normal outputs.
1 = All outputs except SOGOUT in high impedance mode.
SOG High Impedance.
0 = Normal SOG output
1 = SOGOUT pin is in high impedance mode.
Field Output Polarity.
Sets the polarity of the field output signal.
0 = Active low => even field, active high => odd field.
1 = Active low => odd field, active high => even field.
2
**** *0**
PLL Sync Filter Enable.
0 = PLL uses raw Hsync/SOG.
1 = PLL uses filtered Hsync/SOG.
Rev. 0 | Page 25 of 44
AD9980
Preliminary Technical Data
Read and
Hexadecimal Write or
Default
Bits Value
Register
Name
Address
Read Only
Description
1
**** **1*
Sync Processing Input Select.
Selects the sync source for the sync processor.
0 = Sync processing uses raw Hsync/SOGIN.
1 = Sync processing uses regenerated Hsync from sync filter.
0
**** ***1
Must be set to 1 for proper operation.
0x21
0x22
0x23
R/W
R/W
R/W
7:0
7:0
7:0
0010 0000
0011 0010
0000 1010
Must be set to default for proper operation.
Must be set to default for proper operation.
Sets the window of time around the regenerated Hsync leading
Sync Filter
Window Width edge (in 25 nS steps) that sync pulses are allowed to pass through.
0x24
RO
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
_*** ****
*_** ****
**_* ****
***_ ****
**** _***
**** *_**
**** **_*
**** ***_
_*** ****
*_** ****
**_* ****
***_ ****
**** _***
**** *_**
**** **_*
Sync Detect
Hsync0 Detection Bit.
0 = Hsync0 is not active.
1 = Hsync0 is active.
Hsync1 Detection Bit.
0 = Hsync 1 is not active.
1 = Hsync 1 is active.
Vsync 0 Detection Bit.
0 = Vsync0 is not active.
1 = Vsync0 is active.
Vsync1 Detection Bit.
0 = Vsync1 is not active.
1 = Vsync1 is active.
SOG0 Detection Bit.
0 = SOG0 is not active.
1 = SOG0 is active.
SOG1 Detection Bit.
0 = SOG1 is not active.
1 = SOG1 is active.
Coast Detection Bit.
0 = External Coast is not active.
1 = External Coast is active.
Clamp Detection Bit.
0 = External clamp is not active.
1 = External clamp is active.
0x25
RO
Sync Polarity
Detect
Hsync0 Polarity.
0 = Hsync0 polarity is active low.
1 = Hsync0 polarity is active high.
Hsync1 Polarity.
0 = Hsync1 polarity is active low.
1 = Hsync1 polarity is active high.
Vsync0 Polarity.
0 = Vsync0 polarity is active low.
1 = Vsync0 polarity is active high.
Vsync1 Polarity.
0 = Vsync1 polarity is active low.
1 = Vsync1 polarity is active high.
Coast Polarity.
0 = External Coast polarity is active low.
1 = External Coast polarity is active high.
Clamp Polarity.
0 = External clamp polarity is active low.
1 = External clamp polarity is active high.
Extraneous Pulses Detected.
0 = No equalization pulses detected on Hsync.
1 = Extraneous pulses detected on Hsync.
Rev. 0 | Page 26 of 44
AD9980
Read and
Hexadecimal Write or
Default
Bits Value
Register
Name
Address
Read Only
Description
0x26
RO
7:0
Hsyncs Per
Vsync MSBs
MSBs of Hsyncs per Vsync count.
0x27
RO
7:4
Hsyncs Per
Vsync LSBs
LSBs of Hsyncs per Vsync count.
0x28
0x29
0x2A
0x2B
0x2C
R/W
R/W
RO
7:0
7:0
7:0
7:0
7:5
4
1011 1111
0000 0010
TestReg1
TestReg2
TestReg3
TestReg4
Offset Hold
Must be written to 0xBF for proper operation.
Must be written to 0x02 for proper operation.
Read-only bits for future use.
RO
Read-only bits for future use.
R/W
000* ****
***0 ****
Must be written to default for proper operation.
Auto-Offset Hold.
Disables the auto-offset and holds the feedback result.
1 = One time update.
0 = Continuous update.
3:0
7:0
7:0
**** 0000
1111 0000
1111 0000
Must be written to default for proper operation.
Must be written to 0xE8 for proper operation.
Must be written to 0xE0 for proper operation.
0x2D
0x2E
R/W
R/W
TestReg5
TestReg6
1 Functions with more than eight control bits, such as PLL divide ratio, gain, and offset, are only updated when the LSBs are written to (for example, Register 0x02 for
PLL divide ratio).
2 Gain registers (Register 0x05, Register 0x07 and Register 0x09) when written to must each be followed with a write to their next register: Register 0x05 and Register
0x06, Register 0x07 and Register 0x08, and Register 0x09 and Register 0x0A.
Rev. 0 | Page 27 of 44
AD9980
Preliminary Technical Data
DETAILED 2-WIRE SERIAL CONTROL REGISTER DESCRIPTIONS
CHIP IDENTIFICATION
CLOCK GENERATOR CONTROL
0x00
7:0
Chip Revision
0x03
7:6
VCO Range Select
An 8-bit register which represents the silicon revision.
Two bits that establish the operating range of the clock
generator. VCORNGE must be set to correspond to
the desired operating frequency (incoming pixel rate).
The PLL gives the best jitter performance at high
frequencies. For this reason, in order to output low
pixel rates and still get good jitter performance, the
PLL actually operates at a higher frequency but then
divides down the clock rate afterwards. See Table 13
for the pixel rates for each VCO range setting. The
PLL output divisor is automatically selected with the
VCO range setting. The power-up default value is 01.
PLL DIVIDER CONTROL
0x01
7:0
PLL Divide Ratio MSBs
The eight MSBs of the 12-bit PLL divide ratio PLLDIV.
The PLL derives a pixel clock from the incoming
Hsync signal. The pixel clock frequency is then
divided by an integer value, such that the output is
phase-locked to Hsync. This PLLDIV value
determines the number of pixel times (pixels plus
horizontal blanking overhead) per line. This is
typically 20% to 30% more than the number of active
pixels in the display.
Table 13. VCO Ranges
VCO Range
Pixel Rates
10 to 21
21 to 42
42 to 84
84 to 95
00
01
10
11
The 12-bit value of the PLL divider supports divide
ratios from 2 to 4095 as long as the output frequency
is within range. The higher the value loaded in this
register, the higher the resulting clock frequency with
respect to a fixed Hsync frequency.
0x03
5:3
Charge Pump Current
Three bits that establish the current driving the loop
filter in the clock generator. The current must be set to
correspond with the desired operating frequency. The
power-up default value is current = 001.
VESA has established some standard timing
specifications, which will assist in determining the
value for PLLDIV as a function of horizontal and
vertical display resolution and frame rate (see Table 9).
However, many computer systems do not conform
precisely to the recommendations and these numbers
should be used only as a guide. The display system
manufacturer should provide automatic or manual
means for optimizing PLLDIV. An incorrectly set
PLLDIV usually produces one or more vertical noise
bars on the display. The greater the error, the greater
the number of bars produced.
Table 14. Charge Pump Currents
Ip2
Ip1
Ip0
Current
50
0
0
0
0
1
1
1
0
0
0
1
100
1
0
150
1
1
250
0
0
350
0
1
500
1
0
750
1
1
1
1500
The power-up default value of PLLDIV is 1693.
PLLDIVM = 0x69, PLLDIVL = 0xDx.
0x03
2
External Clock Enable
The AD9980 updates the full divide ratio only when
the LSBs are written. Writing to this register by itself
does not trigger an update.
This bit determines the source of the pixel clock.
Table 15. External Clock Select Settings
EXTCLK
Function
0
1
Internally generated clock
Externally provided clock signal
0x02
7:4
PLL Divide Ratio LSBs
The four LSBs of the 12-bit PLL divide ratio PLLDIV.
A Logic 0 enables the internal PLL that generates the
pixel clock from an externally provided Hsync.
The power-up default value of PLLDIV is 1693.
PLLDIVM = 0x69, PLLDIVL = 0xDx.
A Logic 1 enables the external EXTCLK input pin. In
this mode, the PLL Divide Ratio (PLLDIV) is ignored.
The clock phase adjust (PHASE) is still functional.
The power-up default value is EXTCLK = 0.
Rev. 0 | Page 28 of 44
AD9980
The 9-bit offset consists of one sign bit plus eight bits.
If the register is programmed to 130, then the output
code will be equal to 130 at the end of the clamp
period. Incrementing the offset register setting by
1 LSB will add 1 LSB of offset, regardless of the auto-
offset setting. Values written to this register are not
updated until the LSB register (Register 0x0C) has also
been written.
PHASE ADJUST
0x04
7:3
Phase adjustment for the DLL to generate the ADC
clock. A 5-bit value that adjusts the sampling phase in
32 steps across one pixel time. Each step represents an
11.25° shift in sampling phase. The power up default
is 16.
0x0C
0x0D
0x0E
0x0F
0x10
7
Red Channel Offset LSB
INPUT GAIN
0x05
6:0
Red Channel Gain Adjust
The LSB of the red channel offset control which
combines with the eight bits of MSB in the previous
register to make nine bits of offset control.
The 7-Bit Red Channel Gain Control. The AD9980
can accommodate input signals with a full-scale range
of 0.5 V to 1.0 V p-p. Setting the red gain to 127
corresponds to an input range of 1.0 V. A red gain of 0
establishes an input range of 0.5 V. Note that
increasing red gain results in the picture having less
contrast (the input signal uses fewer of the available
converter codes). Values written to this register will
not be updated until the following register
7:0
Green Channel Offset
The 8-Bit Green Channel Offset Control. See red
channel offset (0x0B). Update of this register occurs
only when Register 0x0E is also written.
7
Green Channel Offset LSB
(Register 0x06) has been written to 0x00. The power-
up default is 100 0000.
The LSB of the green channel offset control which
combines with the eight bits of MSB in the previous
register to make nine bits of offset control.
0x07
0x09
6:0 Green Channel Gain Adjust
7:0
Blue Channel Offset
The 7-Bit Green Channel Gain Control. See red
channel gain adjust above. Register update requires
writing 0x00 to Register 0x08.
The 8-Bit Blue Channel Offset Control. See red
channel offset (0x0B). Update of this register occurs
only when Register 0x10 is also written.
6:0
Blue Channel Gain Adjust
7
Blue Channel Offset LSB
The 7-Bit Blue Channel Gain Control. See red channel
gain adjust above. Register update requires writing
0x00 to Register 0x0A.
The LSB of the blue channel offset control which
combines with the eight bits of MSB in the previous
register to make nine bits of offset control.
INPUT OFFSET
0x0B
7:0
Red Channel Offset
HSYNC CONTROLS
0x11
7:0
Sync Separator Threshold
The 8-Bit MSB of the Red Channel Offset Control.
Along with the LSB in the following register, there are
nine bits of dc offset control in the red channel. The
offset control shifts the analog input, resulting in a
change in brightness. Note that the function of the
offset register depends on whether auto-offset is
enabled (Register 0x1B, Bit 5).
This register sets the threshold of the sync separator’s
digital comparator. The value written to this register is
multiplied by 200 ns to get the threshold value.
Therefore, if a value of 5 is written, the digital
comparator threshold is 1 µs and any pulses less than
1 µS are rejected by the sync separator. There is some
variability to the 200 ns multiplier value. The maxi-
mum variability over all operating conditions is 20%
(160 nS to 240 ns). Since normal Vsync and Hsync
pulse widths differ by a factor of about 500 or more,
the 20% variability is not an issue. The power-up
default value is 32 DDR.
If auto-offset is disabled, the lower seven bits of the
offset registers (for the red channel Register 0x0B, Bits
[5:0] plus Register 0x0C, Bit 7) control the absolute
offset added to the channel. The offset control
provides a 63 LSBs of adjustment range, with one
LSB of offset corresponding to 1 LSB of output code.
If auto-offset is enabled, the 9-bit offset (comprised of
the 8 bits of the MSB register and Bit 7 of the
following register) determines the clamp target code.
Rev. 0 | Page 29 of 44
AD9980
Preliminary Technical Data
Table 20. Hsync Output Polarity Settings
0x12
7
Hsync Source Override
Hsync Output
Polarity Bit
Result
This is the active Hsync override. Setting this to 0
allows the chip to determine the active Hsync source.
Setting it to 1 uses Bit 6 of Register 0x12 to determine
the active Hsync source. Power-up default value is 0.
0
1
Hsync Output Polarity is Negative
Hsync Output Polarity is Positive
0x13
7:0
Hsync Duration
Table 16. Active Hsync Source Override
An 8-bit register that sets the duration of the Hsync
output pulse. The leading edge of the Hsync output is
triggered by the internally-generated, phase-adjusted
PLL feedback clock. The AD9980 then counts a
number of pixel clocks equal to the value in this
register. This triggers the trailing edge of the Hsync
output, which is also phase-adjusted.
Override
Result
0
1
Hsync Source determined by chip
Hsync Source determined by user
Register 0x12, Bit 6
0x12
6
Hsync Source
This bit selects the source of the Hsync for PLL and
sync processing only if Bit 7 of Register 0x12 is set to 1
or if both syncs are active. Setting this bit to 0 specifies
the Hsync from the input pin. Setting it to 1 selects
Hsync from SOG. Power-up default is 0.
VSYNC CONTROLS
0x14
7
Vsync Source Override
This is the active Vsync override. Setting this to 0
allows the chip to determine the active Vsync source.
Setting it to 1 uses Bit 6 of Register 0x14 to determine
the active Vsync source. Power-up default value is 0.
Table 17. Active Hsync Select Settings
Select
Result
0
1
Hsync Input
Hsync from SOG
Table 21. Active Vsync Source Override
Override
Result
0x12
5
Hsync Input Polarity Override
0
1
Vsync source determined by chip
Vsync source determined by user
Register 0x14, Bit 6
This bit sets whether the chip selects the Hsync input
polarity or if it is specified. Setting this bit to 0 allows
the chip to automatically select the polarity of the
input Hsync. Setting this bit to 1 indicates that Bit 4 of
Register 0x12 specifies the polarity. Power-up default
is 0.
0x14
6
Vsync Source
This bit selects the source of Vsync for sync
processing only if Bit 7 of Register 0x14 is set to 1.
Setting Bit 6 to 0 specifies Vsync from the input pin.
Setting it to 1 selects Vsync from the sync separator.
Power-up default is 0.
Table 18. Hsync Input Polarity Override Settings
Override Bit
Result
0
1
Hsync Polarity Determined by Chip
Hsync Polarity Determined by User
Register 0x12, Bit 4
Table 22. Active Vsync Select Settings
Select
Result
0
1
Vsync input
Vsync from sync separator
0x12
4
Input Hsync Polarity
If Bit 5 of Register 0x12 is 1, the value of this bit
specifies the polarity of the input Hsync. Setting this
bit to 0 indicates an active low Hsync; setting this bit
to 1 indicates an active high Hsync. Power-up default
is 1.
0x14
5
Vsync Input Polarity Override
This bit sets whether the chip selects the Vsync input
polarity or if it is specified. Setting this bit to 0 allows
the chip to automatically select the polarity of the
input Vsync. Setting this bit to 1 indicates that Bit 4 of
Register 0x14 specifies the polarity. Power-up default
is 0.
Table 19. Hsync Input Polarity Settings
Hsync Polarity Bit
Result
0
1
Hsync Input Polarity is Negative
Hsync Input Polarity is Positive
Table 23. Vsync Input Polarity Override Settings
Override Bit
Result
0x12
3
Hsync Output Polarity
0
1
Vsync polarity determined by chip
Vsync polarity determined by user
Register 0x14, Bit 4
This bit sets the polarity of the Hsync output. Setting
this bit to 0 sets the Hsync output to active low. Setting
this bit to 1 sets the Hsync output to active high.
Power-up default setting is 1.
Rev. 0 | Page 30 of 44
AD9980
0x14
4
Input Vsync Polarity
COAST AND CLAMP CONTROLS
0x16
0x17
0x18
7:0
Precoast
If Bit 5 of Register 0x14 is 1, the value of this bit
specifies the polarity of the input Vsync. Setting this
bit to 0 indicates an active low Vsync; setting this bit to
1 indicates an active high Vsync. Power-up default is 1.
This register allows the internally generated Coast
signal to be applied prior to the Vsync signal. This is
necessary in cases where pre-equalization pulses are
present. The step size for this control is one Hsync
period. For Precoast to work correctly, it is necessary
for the Vsync filter (Register 0x14, Bit 2) and sync
processing filter (Register 0x20, Bit 1) both to be either
enabled or disabled. The power-up default is 00.
Table 24. Vsync Input Polarity Settings
Override Bit
Result
0
1
Vsync input polarity is negative
Vsync input polarity is positive
0x14
3
Vsync Output Polarity
7:0
Postcoast
This bit sets the polarity of the Hsync output. Setting
this bit to 0 sets the Hsync output to active low. Setting
this bit to 1 sets the Hsync output to active high.
Power-up default is 1.
This register allows the internally generated Coast
signal to be applied following the Vsync signal. This is
necessary in cases where post equalization pulses are
present. The step size for this control is one Hsync
period. For Postcoast to work correctly, it is necessary
for the Vsync filter (Register 0x14, Bit 2) and sync
processing filter (Register 0x20, Bit 1) both to be either
enabled or disabled. The power-up default is 00.
Table 25. Vsync Output Polarity Settings
Vsync Output
Polarity Bit
Result
0
1
Vsync output polarity is negative
Vsync output polarity is positive
0x14
2
Vsync Filter Enable
7
Coast Source
This bit enables the Vsync filter allowing precise
placement of the Vsync with respect to the Hsync
and facilitating the correct operation of the
Hsyncs/Vsync count.
This bit is used to select the active Coast source. The
choices are the COAST input pin or Vsync. If Vsync is
selected, the additional decision of using the Vsync
input pin or the output from the sync separator needs
to be made (Register 0x14, Bits [7: 6]).
Table 26. Vsync Filter Enable
Vsync Filter Bit
Result
Table 28. Coast Source Selection Settings
0
1
Vsync filter disabled
Vsync filter enabled
Select
Result
0
1
Vsync (internal Coast)
COAST input pin
0x14
1
Vsync Duration Enable
0x18
6
Coast Polarity Override
This enables the Vsync duration block, which is
designed to be used with the Vsync filter. Setting the
bit to 0 leaves the Vsync output duration unchanged.
Setting the bit to 1 sets the Vsync output duration
based on Register 0x15. Power-up duration is 0.
This register is used to override the internal circuitry
that determines the polarity of the Coast signal going
into the PLL. The power-up default setting is 0.
Table 29. Coast Polarity Override Settings
Override Bit
0
1
Table 27. Vsync Duration Enable
Result
Vsync
Coast polarity determined by chip
Coast polarity determined by user
Duration Bit
Result
0
1
Vsync output duration is unchanged
Vsync output duration is set by Register 0x15
0x18
5
Input Coast Polarity
0x15
7:0
Vsync Duration
This register sets the input Coast polarity when Bit 6
of Register 0x18 = 1. The power-up default setting is 1.
This is used to set the output duration of the Vsync,
and is designed to be used with the Vsync filter. This is
valid only if Register 0x14, Bit 1 is set to 1. Power-up
default is 10.
Table 30. Coast Polarity Settings
Coast Polarity
Bit
Result
0
1
Coast polarity is negative
Coast polarity is positive
Rev. 0 | Page 31 of 44
AD9980
Preliminary Technical Data
0x18
4
Clamp Source
The clamp placement may be programmed to
any value between 1 and 255. A value of 0 is
not supported.
This bit determines the source of clamp timing. A 0
enables the clamp timing circuitry controlled by
clamp placement and clamp duration. The clamp posi-
tion and duration is counted from the leading edge of
Hsync. A 1 enables the external clamp input pin. The
three channels are clamped when the clamp signal is
active. The polarity of clamp is determined by the
clamp polarity bit. The power-up default setting
is 0.
The clamp should be placed during a time that the
input signal presents a stable black-level reference,
usually the back porch period between Hsync and the
image. When EXTCLMP = 1, this register is ignored.
Power-up default setting is 8.
0x1A
7:0
Clamp Duration
An 8-bit register that sets the duration of the
internally generated clamp.
Table 31. Clamp Source Selection Settings
Clamp Source
Result
0
1
Internally generated clamp
Externally provided clamp signal
When EXTCLMP = 0 (Register 0x18, Bit 4), a clamp
signal is generated internally at a position established
by the clamp placement register and for a duration set
by the clamp duration register. Clamping begins a
clamp placement (Register 0x19) count of pixel peri-
ods after the trailing edge of Hsync. The clamp dura-
tion may be programmed to any value between 1 and
255. A value of 0 is not supported.
0x18
3
Red Clamp Select
This bit determines whether the red channel is
clamped to ground or to midscale. The power-up
default setting is 0.
Table 32. Red Clamp Select Settings
Clamp
Result
For the best results, the clamp duration should be set
to include the majority of the black reference signal
time that follows the Hsync signal trailing edge.
Insufficient clamping time can produce brightness
changes at the top of the screen, and a slow recovery
from large changes in the average picture level (APL),
or brightness. When EXTCLMP = 1, this register is
ignored. Power-up default setting is 20 DDR.
0
1
Clamp to ground
Clamp to midscale
0x18
2
Green Clamp Select
This bit determines whether the green channel is
clamped to ground or to midscale. The power-up
default setting is 0.
Table 33. Green Clamp Select Settings
0x1B
7
Clamp Polarity Override
Clamp
Result
0
1
Clamp to ground
Clamp to midscale
This bit is used to override the internal circuitry that
determines the polarity of the clamp signal. The
power-up default setting is 0.
0x18
1
Blue Clamp Select
Table 35. Clamp Polarity Override Settings
This bit determines whether the blue channel is
clamped to ground or to midscale. The power-up
default setting is 0.
Override Bit
Result
0
1
Clamp polarity determined by chip
Clamp polarity determined by user
Register 0x1B, Bit 6
Table 34. Blue Clamp Select Settings
Clamp
Result
0x1B
6
Input Clamp Polarity
0
1
Clamp to ground
Clamp to midscale
This bit indicates the polarity of the clamp signal only
if Bit 7 of Register 0x1B = 1. The power-up default
setting is 1.
0x19
7:0
Clamp Placement
An 8-bit register that sets the position of the internally
generated clamp.
Table 36. Clamp Polarity Override Settings
CLMPOL
Result
When EXTCLMP = 0 (Register 0x18, Bit 4), a clamp
signal is generated internally at a position established
by the clamp placement register (0x19) and for a
duration set by the clamp duration register (0x1A).
Clamping starts a clamp placement (Register 0x19)
count of pixel periods after the trailing edge of Hsync.
0
1
Active low
Active high
Rev. 0 | Page 32 of 44
AD9980
excludes extraneous syncs not occurring within the
sync filter window. The power-up default setting is 0.
0x1B
5
Auto-Offset Enable
This bit selects between auto-offset mode and manual
offset mode (auto-offset disabled). See the section on
auto-offset operation. The power-up default setting
is 0.
Table 40. SOGOUT Polarity Settings
SOGOUT Select
Function
00
01
10
11
Raw SOG from sync slicer (SOG0 or SOG1)
Raw Hsync (Hsync0 or Hsync1)
Regenerated sync from sync filter
Filtered sync from sync filter
Table 37. Auto-Offset Settings
Auto-Offset
Result
0
1
Auto-offset is disabled
Auto-offset is enabled (manual offset
mode)
INPUT AND POWER CONTROL
0x1E
7
Channel Select Override
0x1B
4:3
Auto-Offset Update Frequency
This bit provides an override to the automatic input
channel selection. Power-up default setting is 0.
These bits control how often the auto-offset circuit is
updated (if enabled). Updating every 64 Hsyncs is
recommended. The power-up default setting is 11.
Table 41. Channel Source Override
Override
Result
0
1
Channel input source determined by chip
Channel input source determined by user
Register 0x1E, Bit 6
Table 38. Auto-Offset Update Mode
Clamp Update
Result
00
01
10
11
Update offset every clamp period
Update offset every 16 clamp periods
Update offset every 64 clamp periods
Update offset every Vsync periods
0x1E
6
Channel Select
This bit selects the active input channel if
Register 0x1E, Bit 7 = 1. This selects between
Channel 0 data and syncs or Channel 1 data and
syncs. Power-up default setting is 0.
0x1B
0x1C
2:0
7:0
Must be written to 011 for proper operation.
TestReg0
Table 42. Channel Select
Must be written to 0xFF for proper operation.
Channel Select
Result
0
1
Channel 0 data and syncs are selected
Channel 1 data and syncs are selected
SOG CONTROL
0x1D
7:3
SOG Comparator Threshold
0x1E
5
Programmable Bandwidth
This register allows the comparator threshold of the
SOG slicer to be adjusted. This register adjusts it in
steps of 8 mV, with the minimum setting equaling
8 mV and the maximum setting equaling 256 mV. The
power-up default setting is 15 and corresponds to a
threshold value of 128 mV.
This bit selects between a low or high input
bandwidth. It is useful in limiting noise for lower
frequency inputs. The power-up default setting is 1.
Low analog input bandwidth is ~100 MHz; high
analog input bandwidth is ~200 MHz.
Table 43. Input Bandwidth Select
0x1D
2
SOG Output Polarity
Input Bandwidth
Result
0
1
Low analog input bandwidth
High analog input bandwidth
This bit sets the polarity of the SOGOUT signal. The
power-up default setting is 0.
0x1E
4
Power-Down Control Select
Table 39. SOGOUT Polarity Settings
SOGOUT
Result
This bit sets whether power-down is controlled
manually or automatically by the chip. If automatic
control is selected (0x1E, Bit 4), the AD9980’s decision
is based on the status of the sync detect bits (Register
0x24, Bits 2, 3, 6, and 7). If either an Hsync or a sync-
on-green input is detected on any input, the chip
powers up, otherwise it powers down. If manual
control is desired, the AD9980 includes flexibility of
control with both a dedicated pin and a register bit.
The dedicated pin allows a hardware watchdog circuit
to control power-down, while the register bit allows
0
1
Active low
Active high
0x1D
1:0
SOG Output Select
These register bits control the output on the SOGOUT
pin. Options are the raw SOG from the slicer (this is
the unprocessed SOG signal produced from the sync
slicer), the raw Hsync, the regenerated sync from the
sync filter that can generate missing syncs either due
to coasting or dropout, and the filtered sync which
Rev. 0 | Page 33 of 44
AD9980
Preliminary Technical Data
power-down to be controlled by software. With
In most cases, SOGOUT is not put in high impedance
during normal operation. It is usually needed for sync
detection by the graphics controller. The option to put
SOGOUT in high impedance is included mainly to
allow for factory testing modes.
manual power-down control, the polarity of the
power-down pin must be set (0x1E, Bit 2) whether it is
used or not. If unused, it is recommended to set the
polarity to active high and to hardwire the pin to
ground with a 10 kΩ resistor.
Table 48. SOGOUT High Impedance Control
Table 44. Auto Power-Down Select
SOGOUT
Control
Result
Power-Down Select
Result
0
The SOGOUT output operates as normal
during power-down.
0
Manual power-down control
User determines power-down
1
The SOGOUT output is in high impedance
during power-down.
1
Auto power-down control
Chip determines power-down
OUTPUT CONTROL
0x1E
3
Power-Down
0x1F
6:5
Output Mode
This bit is used to manually put the chip in power-
down mode. It is used only if manual power-down
control is selected (see Bit 4 of the power-down
register). Both the state of this register bit and the
power-down pin (Pin 17) are used to control manual
power-down (see the Power Management section for
more details on power-down.).
These bits choose between three options for the
output mode. In 4:4:4 mode RGB is standard, in 4:2:2
mode YCbCr is standard, which allows a reduction in
the number of output pins from 24 to 16. In 4:4:4
DDR output mode, the data is in RGB mode but
changes on every clock edge. The power-up default
setting is 00.
Table 45. Power-Down Settings
Power-Down Select
Pin 17
Result
Table 49. Output Mode
0
1
0
X
Normal operation
Power-down
Output Mode
Result
00
01
10
4:4:4 RGB mode
4:2:2 YCbCr mode
4:4:4 DDR mode
0x1E
2
Power-Down Polarity
This bit defines the polarity of the power-down pin (Pin 17). It
is only used if manual power-down control is selected (see Bit 4
above).
0x1F
4
Primary Output Enable
This bit places the primary output in active or high
impedance mode. The power-up default setting is 1.
Table 46. Power-Down Pin Polarity
Select
Result
Table 50. Primary Output Enable
0
1
Power-down pin is active low
Power-down pin is active high
Select
Result
0
1
Primary output is in high impedance mode
Primary output is enabled
0x1E
1
Power-Down Fast Switching Control
0x1F
3
Secondary Output Enable
This bit controls a special fast switching mode. With
this bit, the AD9980 can stay active during power-
down and only put the outputs in high impedance.
This option is useful when the data outputs from two
chips are connected on a PCB and the user wants to
switch instantaneously between the two.
This bit places the secondary output in active or high
impedance mode.
The secondary output is designated when using either
4:2:2 or 4:4:4 DDR. In these modes, the data on the
blue output channel is the secondary output while the
output data on the red and green channels are the
primary output. Secondary output is always a YCbCr
DDR data mode. See the Output Formatter section
and Table 11. The power-up default setting is 0.
Table 47. Power-Down Fast Switching Control
Fast
Switching Control
Result
0
1
Normal power-down operation
The chip stays powered-up and the
outputs are put in high impedance
mode
Table 51. Secondary Output Enable
Select
Result
0
1
Secondary output is in high impedance mode
Secondary output is enabled
0x1E
0
SOGOUT High Impedance Control
This bit controls whether the SOGOUT output pin is
in high impedance or not when in power-down mode.
Rev. 0 | Page 34 of 44
AD9980
0x20
3
Field Output Polarity
0x1F
2:1
Output Drive Strength
This bit sets the polarity of the field output bit. The
power-up default setting is 1.
These two bits select the drive strength for all high-
speed digital outputs (except VSOUT, A0, and the O/E
field). Higher drive strength results in faster rise/fall
times and in general makes it easier to capture data.
Lower drive strength results in slower rise/fall times
and helps reduce EMI and digitally generated power
supply noise. The power-up default setting is 10.
Table 57. Field Output Polarity
Select
Result
0
1
Active low = even field; active high = odd field
Active low = odd field; active high = even field
Table 52. Output Drive Strength
SYNC PROCESSING
Output
0x20
2
PLL Sync Filter
Drive
Result
00
01
10
11
Low output drive strength
Medium low output drive strength
Medium high output drive strength
High output drive strength
This bit selects which signal the PLL uses. It can select
between either raw Hsync or SOG or filtered versions.
The filtering of the Hsync and SOG can eliminate
nearly all extraneous transitions which have tradi-
tionally caused PLL disruption. The power-up default
setting is 0.
0x1F
0
Output Clock Invert
This bit allows inversion of the output clock. The
power-up default setting is 0.
Table 58. PLL Sync Filter Enable
Select
Result
Table 53. Output Clock Invert
Select
0
1
PLL uses raw Hsync or SOG inputs
PLL uses filtered Hsync or SOG inputs
Result
0
1
Noninverted pixel clock
Inverted pixel clock
0x20
1
Sync Processing Input Source
0x20
7:6
Output Clock Select
This bit selects whether the sync processor uses a raw
sync or a regenerated sync for the following functions:
Coast, H/V count, field detection and Vsync duration
counts. Using the regenerated sync is recommended.
These bits allow selection of optional output clocks
such as a fixed 40 MHz clock, a 2× clock, a 90° phase-
shifted clock or the normal pixel clock. The power-up
default setting is 00.
Table 59. SP Filter Enable
Select
Result
Table 54. Output Clock Select
Select
0
1
Sync processing uses raw Hsync or SOG
Sync processing uses the internally regenerated
Hsync
Result
00
Pixel clock
01
10
11
90° phase-shifted pixel clock
2× pixel clock
40 MHz internal clock
0x20
0x21
0x22
0x23
0
Must be set to 1 for proper operation
Must be set to default
7:0
7:0
7:0
0x20
5
Output High Impedance
Must be set to default
This bit puts all outputs (except SOGOUT) in a high impedance
state. The power-up default setting is 0.
Sync Filter Window Width
This 8-bit register sets the window of time for the regenerated
Hsync leading edge (in 25 ns steps) when sync pulses are
allowed to pass through. Therefore with the default value of 10,
the window width is 250 ns. The goal is to set the window
width so that extraneous pulses are rejected. (see the Sync
Processing section). As in the sync separator threshold, the
25 ns multiplier value is somewhat variable. The maximum
variability over all operating conditions is 20% (20 ns to
30 ns).
Table 55. Output High Impedance
Select Result
0
1
Normal outputs
All outputs (except SOGOUT) in high impedance mode
0x20
4
SOG High Impedance
This bit allows the SOGOUT pin to be placed in high
impedance mode. The power-up default setting is 0.
Table 56. SOGOUT High Impedance
Select
Result
0
1
Normal SOG output
SOGOUT pin is in high impedance mode
Rev. 0 | Page 35 of 44
AD9980
Preliminary Technical Data
Table 64. SOG0 Detection Results
DETECTION STATUS
Detect
Result
0x24
7
Hsync0 Detection Bit
0
1
No activity detected
Activity detected
This bit is used to indicate when activity is detected on
the HSYNC0 input pin. If Hsync is held high or low,
activity will not be detected. The sync processing
block diagram shows where this function is imple-
mented. 0 = Hsync0 is not active. 1 = Hsync0 is active.
0x24
2
SOG1 Detection Bit
This bit is used to indicate when activity is detected on
the SOG1 input pin. If SOG is held high or low,
activity is not detected. The sync processing block
diagram shows where this function is implemented.
0 = SOG1 not active. 1 = SOG1 is active.
Table 60. Hsync0 Detection Results
Detect
Result
0
1
No activity detected
Activity detected
Table 65. SOG1 Detection Results
Detect
Result
0x24
6
Hsync1 Detection Bit
0
1
No activity detected
Activity detected
This bit is used to indicate when activity is detected on
the HSYNC1 input pin. If Hsync is held high or low,
activity is not detected. The sync processing block
diagram shows where this function is implemented.
0 = Hsync1 is not active. 1 = Hsync1 is active.
0x24
1
Coast Detection Bit
This bit detects activity on the EXTCLK/EXTCOAST
pin. It indicates one of the two signals is active, but it
won’t indicate if it is EXTCLK or EXTCOAST. A dc
signal is not detected.
Table 61. Hsync1 Detection Results
Detect
Result
Table 66. COAST Detection Result
Detect
0
1
No activity detected
Activity detected
Result
0
1
No activity detected
Activity detected
0x24
5
Vsync0 Detection Bit
This bit is used to indicate when activity is detected on
the VSYNC0 input pin. If Vsync is held high or low,
activity is not detected. The sync processing block
diagram shows where this function is implemented.
0 = Vsync0 not active. 1 = Vsync0 is active.
0x24
0
Clamp Detection Bit
This bit is used to indicate when activity is detected on
the external clamp pin. If external clamp is held high
or low, activity is not detected.
Table 67. Clamp Detection Results
Table 62. Vsync0 Detection Results
Detect
Result
Detect
Result
0
1
No activity detected
Activity detected
0
1
No activity detected
Activity detected
0x24
4
Vsync1 Detection Bit
POLARITY STATUS
This bit is used to indicate when activity is detected on
the Vsync1 input pin. If Vsync is held high or low,
activity is not detected. The sync processing block
diagram shows where this function is implemented.
0 = Vsync1 is not active, 1 = Vsync1 is active.
0x25
7
Hsync0 Polarity
Indicates the polarity of Hsync0 input.
Table 68. Detected Hsync0 Polarity Results
Detect
Result
Table 63. Vsync1 Detection Results
0
1
Hsync polarity is negative
Hsync polarity is positive
Detect
Result
0
1
No activity detected
Activity detected
0x25
6
Hsync1 Polarity
Indicates the polarity of Hsync1 input.
Table 69. Detected Hsync1 Polarity Results
0x24
3
SOG0 Detection Bit
This bit is used to indicate when activity is detected on
the SOG0 input pin. If SOG is held high or low,
activity is not detected. The sync processing block
diagram shows where this function is implemented.
0 = SOG0 is not active. 1 = SOG1 is active.
Detect
Result
0
1
Hsync polarity is negative
Hsync polarity is positive
Rev. 0 | Page 36 of 44
AD9980
0x25
5
Vsync0 Polarity
Indicates the polarity of Vsync0 input.
Table 70. Detected Vsync0 Polarity Results
Test Registers
0x28
0x29
0x2A
0x2B
0x2C
0x2C
7:0
Must be written to 0xBF for proper operation.
7:0 Test Register 2
Must be written to 0x00 for proper operation.
7:0 Test Register 3
Read only bits for future use.
7:0 Test Register 4
Test Register 1
Detect
Result
0
1
Vsync polarity is negative
Vsync polarity is positive
0x25
4
Vsync1 Polarity
Indicates the polarity of Vsync1 input.
Table 71. Detected Vsync1 Polarity Results
Detect
Result
0
1
Vsync polarity is negative
Vsync polarity is positive
Read only bits for future use.
7:5
0x25
3
Coast Polarity
Indicates the polarity of the external Coast signal.
Table 72. Detected Coast Polarity Results
Must be written to 000 for proper operation.
4
Auto-Offset Hold
Detect
Result
A bit for controlling whether the auto-offset function
runs continuously or runs once and holds the result.
Continuous updates are recommended because it
allows the AD9980 to compensate for drift-over time,
temperature, etc. If one-time updates are preferred,
these should be performed every time the part is
powered up and when there is a mode change. To do a
one-time update, first auto-offset must be enabled
(Register 0x1B, Bit 5). Next, this bit (auto-offset hold)
must first be set to 0 to let the auto-offset function
operate and settle to a final value. Auto-offset hold
should then be set to 1 to hold the offset values that
the auto circuitry calculates. The AD9980’s auto-offset
circuit’s maximum settle time is 10 updates. For
example, if the update frequency is set to once every
64 Hsyncs, then the maximum settling time would be
640 Hsyncs (10 × 64 Hsyncs).
0
1
Coast polarity is negative
Coast polarity is positive
0x25
2
Clamp Polarity
Indicates the polarity of the clamp signal.
Table 73. Detected Clamp Polarity Results
Detect
Result
0
1
Clamp polarity is negative
Clamp polarity is positive
0x25
1
Extraneous Pulses Detection
A second output from the Hsync filter, this status bit tells
whether extraneous pulses are present on the incoming sync
signal. Often extraneous pulses are used for copy protection, so
this status bit can be used for this purpose.
Table 74. Equalization Pulse Detect Bit
Table 75. Auto-Offset Hold
Detect
Result
Select
Result
0
No equalization pulses detected during
active Hsync
Equalization pulses detected during
active Hsync
0
1
Allows auto-offset to update continuously
Disables auto-offset updates and holds the
current auto-offset values
1
HSYNC COUNT
0x26
7:0
Hsyncs/Vsync MSB
0x2C
3:0
7:0
Must be written to 0x0 for proper operation.
The 8 MSBs of the 12-bit counter that reports the
number of Hsyncs/Vsync on the active input. This is
useful for determining the mode and is an aid in
setting the PLL divide ratio.
0x2D
Test Register 5
Read/write bits for future use. Must be written to
0xE8 for proper operation.
0x2E
7:0
Test Register 6
0x27
7:4
Hsyncs/Vsync LSBs
Read/write bits for future use. Must be written to
0xE0 for proper operation.
The 4 LSBs of the 12-bit counter that reports the
number of Hsyncs/Vsync on the active input.
Rev. 0 | Page 37 of 44
AD9980
Preliminary Technical Data
Table 76. Serial Port Addresses
TWO-WIRE SERIAL CONTROL PORT
Bit 7
Bit 6
A5
0
Bit 5
A4
0
Bit 4
A3
1
Bit 3
A2
1
Bit 2
A1
0
Bit 1
A0
0
A two-wire serial interface control interface is provided. Up to
two AD9980 devices may be connected to the two-wire serial
interface with each device having a unique address.
A6 (MSB)
1
1
0
0
1
1
0
1
DATA TRANSFER VIA SERIAL INTERFACE
The two-wire serial interface comprises a clock (SCL) and a bi-
directional data pin (SDA). The analog flat panel interface acts
as a slave for receiving and transmitting data over the serial
interface. When the serial interface is not active, the logic levels
on SCL and SDA are pulled high by external pull-up resistors.
For each byte of data read or written, the MSB is the first bit in
the sequence.
If the AD9980 does not acknowledge the master device during a
write sequence, the SDA remains high so the master can gener-
ate a stop signal. If the master device does not acknowledge the
AD9980 during a read sequence, the AD9980 interprets this as
end-of-data. The SDA remains high so the master can generate
a stop signal.
Data received or transmitted on the SDA line must be stable for
the duration of the positive going SCL pulse. Data on SDA must
change only when SCL is low. If SDA changes state while SCL is
high, the serial interface interprets that action as a start or stop
sequence.
Writing data to specific control registers of the AD9980 requires
that the 8-bit address of the control register of interest be writ-
ten after the slave address has been established. This control
register address is the base address for subsequent write opera-
tions. The base address auto-increments by one for each byte of
data written after the data byte intended for the base address. If
more bytes are transferred than there are available addresses,
the address will not increment and remains at its maximum
value of 0x2E. Any base address higher than 0x2E does not pro-
duce an acknowledge signal. Data are read from the control
registers of the AD9980 in a similar manner. Reading requires
two data transfer operations:
The following are the five components to serial bus operation:
•
•
•
•
•
Start signal
Slave address byte
Base register address byte
Data byte to read or write
Stop signal
When the serial interface is inactive (SCL and SDA are high),
communication is initiated by sending a start signal. The start
signal is a high-to-low transition on SDA while SCL is high.
This signal alerts all slaved devices that a data transfer sequence
is coming.
The base address must be written with the R/W bit of the slave
address byte low to set up a sequential read operation. Reading
(the R/W\ bit of the slave address byte high) begins at the
previously established base address. The address of the read
register auto-increments after each byte is transferred.
The first eight bits of data transferred after a start signal
comprise a 7-bit slave address (the first seven bits) and a single
R/W\ bit (the eighth bit). The R/W\ bit indicates the direction
of data transfer: read from 1 or write to 0 on the slave device. If
the transmitted slave address matches the address of the device
(set by the state of the Serial A0 address [SA0] input pin in
Table 76), the AD9980 acknowledges the match by bringing
SDA low on the ninth SCL pulse. If the addresses do not match,
the AD9980 does not acknowledge it.
To terminate a read/write sequence to the AD9980, a stop signal
must be sent. A stop signal comprises a low-to-high transition
of SDA while SCL is high.
A repeated start signal occurs when the master device driving
the serial interface generates a start signal without first gener-
ating a stop signal to terminate the current communication.
This is used to change the mode of communication (read, write)
between the slave and master without releasing the serial
interface lines.
SDA
tBUFF
tDSU
tDHO
tSTOSU
tSTASU
tSTAH
tDAL
SCL
tDAH
Figure 17. Serial Port Read/Write Timing
Rev. 0 | Page 38 of 44
AD9980
Serial Interface Read/Write Examples
Read from one control register:
Write to one control register:
•
•
•
•
•
•
•
Start signal
•
•
•
•
•
Start signal
Slave address byte (R/W\ bit = low)
Base address byte
Slave address byte (R/W\ bit = low)
Base address byte
Start signal
Data byte to base address
Stop signal
Slave address byte (R/W\ bit = high)
Data byte from base address
Stop signal
Write to four consecutive control registers:
•
•
•
•
•
•
•
•
Start signal
Read from four consecutive control registers:
Slave address byte (R/W\ bit = low)
Base address byte
•
•
•
•
•
•
•
•
•
•
Start signal
Slave address byte (R/W\ bit = low)
Base address byte
Data byte to base address
Data byte to (base address + 1)
Data byte to (base address + 2)
Data byte to (base address + 3)
Stop signal
Start signal
Slave address byte (R/W\ bit = high)
Data byte from base address
Data byte from (base address + 1)
Data byte from (base address + 2)
Data byte from (base address + 3)
Stop signal
SDA
SCL
BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0
ACK
BIT 7
Figure 18. Serial Interface—Typical Byte Transfer
Rev. 0 | Page 39 of 44
AD9980
The bypass capacitors should be physically located between the
power plane and the power pin. Current should flow from the
power plane > capacitor > power pin. Do not make the power
connection between the capacitor and the power pin. Placing a
via underneath the capacitor pads, down to the power plane, is
generally the best approach.
PCB LAYOUT RECOMMENDATIONS
The AD9980 is a high-precision, high-speed analog device.
To achieve the maximum performance from the part, it is
important to have a well laid-out board. The Analog Interface
Inputs section contains a guide for designing a board using
the AD9980.
It is particularly important to maintain low noise and good
stability of PVD (the clock generator supply). Abrupt changes in
PVD can result in similarly abrupt changes in sampling clock
phase and frequency. This can be avoided by careful attention to
regulation, filtering, and bypassing. It is highly desirable to
provide separate regulated supplies for each of the analog
circuitry groups (VD and PVD).
Analog Interface Inputs
Using the following layout techniques on the graphics inputs is
extremely important:
1. Minimize the trace length running into the graphics inputs.
This is accomplished by placing the AD9980 as close as
possible to the graphics VGA connector. Long input trace
lengths are undesirable because they pick up noise from
the board and other external sources.
Some graphic controllers use substantially different levels of
power when active (during active picture time) and when idle
(during horizontal and vertical sync periods). This can result in
a measurable change in the voltage supplied to the analog
supply regulator, which in turn can produce changes in the
regulated analog supply voltage. This can be mitigated by
regulating the analog supply, or at least PVD, from a different,
cleaner, power source (for example, from a 12 V supply).
2. Place the 75 Ω termination resistors (see Figure 3) as close
as possible to the AD9980 chip. Any additional trace length
between the termination resistors and the input of the
AD9980 increases the magnitude of reflections, which
corrupts the graphics signal.
3. Use 75 Ω matched impedance traces. Trace impedances
other than 75 Ω also increases the chance of reflections.
It is also recommended to use a single ground plane for the
entire board. Experience has repeatedly shown that the noise
performance is the same or better with a single ground plane.
Using multiple ground planes can be detrimental because each
separate ground plane is smaller and long ground loops can
result.
4. The AD9980 has very high input bandwidth (200 MHz).
While this is desirable for acquiring a high resolution PC
graphics signal with fast edges, it also means that it
captures any high frequency noise present. Therefore, it is
important to reduce the amount of noise that gets coupled
to the inputs. Avoid running any digital traces near the
analog inputs.
In some cases, using separate ground planes is unavoidable. For
those cases, it is recommended to at least place a single ground
plane under the AD9980. The location of the split should be at
the receiver of the digital outputs. In this case, it is even more
important to place components wisely because the current
loops will be much longer (current takes the path of least
resistance). An example of a current loop is power plane to
AD9980 to digital output trace to digital data receiver to digital
ground plane to analog ground plane.
5. Due to the high bandwidth of the AD9980, sometimes
low-pass filtering the analog inputs can help to reduce
noise. (For many applications, filtering is unnecessary.)
Experiments have shown that placing a ferrite bead in
series prior to the 75 Ω termination resistor is helpful in
filtering excess noise. Specifically, the Fair-Rite
#2508051217Z0 was used, but an application could work
best with a different bead value. Alternatively, placing a
100 Ω to 120 Ω resistor between the 75 Ω termination
resistor and the input coupling capacitor is beneficial.
PLL
Place the PLL loop filter components as close to the FILT pin as
possible. Do not place any digital or other high frequency traces
near these components. Use the values suggested in the data-
sheet with 10% tolerances or less.
Power Supply Bypassing
It is recommended to bypass each power supply pin with a
0.1 µF capacitor. The exception is where two or more supply
pins are adjacent to each other. For these groupings of
powers/grounds, it is only necessary to have one bypass
capacitor. The fundamental idea is to have a bypass capacitor
within about 0.5 cm of each power pin. Also, avoid placing the
capacitor on the opposite side of the PC board from the
AD9980, since that interposes resistive vias in the path.
Outputs (Both Data and Clocks)
Try to minimize the trace length that the digital outputs have to
drive. Longer traces have higher capacitance and require more
instantaneous current to drive, which creates more internal
digital noise. Shorter traces reduce the possibility of reflections.
Rev. 0 | Page 40 of 44
AD9980
Digital Inputs
Adding a series resistor of value 50 Ω to 200 Ω can suppress
reflections, reduce EMI, and reduce the current spikes inside the
AD9980. If series resistors are used, place them as close to the
AD9980 pins as possible, (although try not to add vias or extra
length to the output trace to get the resistors closer).
Digital inputs on the AD9980 (HSYNC0, HSYNC1, VSYNC0,
VSYNC1, SOGIN0, SOGIN1, SDA, SCL and CLAMP) were
designed to work with 3.3 V signals, but are tolerant of 5.0 V
signals. Therefore, no extra components need to be added if
using 5.0 V logic.
If possible, limit the capacitance that each digital output drives
to less than 10 pF. This is easily accomplished by keeping traces
short and by connecting the outputs to only one device. Loading
the outputs with excessive capacitance increases the current
transients inside of the AD9980 and creates more digital noise
on its power supplies.
Any noise that gets onto the Hsync input trace adds jitter to the
system. Therefore, minimize the trace length and do not run
any digital or other high frequency traces near it.
Reference Bypass
The AD9980 has three reference voltages that must be bypassed
for proper operation of the input PGA. REFLO and REFHI are
connected to each other through a 10 µF capacitor. REFCM is
connected to ground through a 10 µF capacitor. These refer-
ences are used by the input PGA circuitry to assure the greatest
stability. Place them as close to the AD9980 pin as possible.
Make the ground connection as short as possible.
Rev. 0 | Page 41 of 44
AD9980
OUTLINE DIMENSIONS
16.00
BSC SQ
0.75
0.60
0.45
1.60
MAX
80
61
60
1
SEATING
PLANE
PIN 1
14.00
BSC SQ
TOP VIEW
(PINS DOWN)
10°
6°
2°
1.45
1.40
1.35
0.20
0.09
7°
VIEW A
20
41
3.5°
0°
40
21
0.15
0.05
SEATING
PLANE
0.10 MAX
COPLANARITY
0.65
BSC
0.38
0.32
0.22
VIEW A
ROTATED 90° CCW
COMPLIANT TO JEDEC STANDARDS MS-026-BEC
Figure 19. 80-Lead Low Profile Quad Flat Pack [LQFP]
(ST-80-2)
Dimensions shown in millimeters
ORDERING GUIDE
Model
AD9980KSTZ-801
AD9980KSTZ-951
AD9980/PCB
Temperature Range
Package Description
80-lead LQFP
Package Option
ST-80-2
0°C to +70°C
0°C to +70°C
80-lead LQFP
ST-80-2
Evaluation Kit
1 Pb-free part.
Rev. 0 | Page 42 of 44
AD9980
NOTES
Rev. 0 | Page 43 of 44
AD9980
NOTES
Purchase of licensed I2C components of Analog Devices or one of its sublicensed Associated Companies conveys a license for the purchaser under the Philips I2C Patent
Rights to use these components in an I2C system, provided that the system conforms to the I2C Standard Specification as defined by Philips.
©
2005 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D04740-0-1/05(0)
Rev. 0 | Page 44 of 44
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明