ADN2807ACP [ADI]
155/622 Mb/s Clock and Data Recovery IC with Integrated Limiting Amp; 155/622 Mb / s的时钟和数据恢复IC，集成限幅放大器
| 型号： | ADN2807ACP |
| 厂家： | 
ADI |
| 描述： | 155/622 Mb/s Clock and Data Recovery IC with Integrated Limiting Amp |
| 文件： | 总20页 (文件大小：354K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
155/622 Mb/s Clock and Data Recovery IC
with Integrated Limiting Amp
ADN2807
GENERAL DESCRIPTION
FEATURES
Meets SONET requirements for jitter transfer/
generation/tolerance
Quantizer sensitivity: 4 mV typical
Adjustable slice level: 100 mV
Patented clock recovery architecture
Loss-of-signal detect range: 3 mV to 15 mV
Single-reference clock frequency for all rates, including
15/14 (7%) wrapper rate
Choice of 19.44 MHz, 38.88 MHz, 77.76 MHz, or
155.52 MHz REFCLK
REFCLK inputs: LVPECL/LVDS/LVCMOS/LVTTL compatible
(LVPECL/LVDS only at 155.52 MHz)
Optional 19.44 MHz on-chip oscillator to be used with
external crystal
Loss-of-lock indicator
The ADN2807 provides the receiver functions of quantization,
signal level detect, and clock and data recovery at rates of OC-3,
OC-12, and 15/14 FEC. All SONET jitter requirements are met,
including jitter transfer, jitter generation, and jitter tolerance. All
specifications are quoted for –40°C to +85°C ambient
temperature, unless otherwise noted.
The device is intended for WDM system applications and can
be used with either an external reference clock or an on-chip
oscillator with external crystal. Both native rates and 15/14 rate
digital wrappers are supported by the ADN2807, without any
change of reference clock.
This device, together with a PIN diode and a TIA preamplifier,
can implement a highly integrated, low cost, low power, fiber
optic receiver.
Loopback mode for high speed test data
Output squelch and bypass features
Single-supply operation: 3.3 V
Low power: 540 mW typical
The receiver front end signal detect circuit indicates when the
input signal level has fallen below a user adjustable threshold.
The signal detect circuit has hysteresis to prevent chatter at the
output.
7 mm × 7 mm, 48-lead LFCSP
APPLICATIONS
SONET OC-3/-12, SDH STM-1/-4 and, 15/14 FEC rates
WDM transponders
The ADN2807 is available in a compact 7 mm × 7 mm 48-lead
chip-scale package (LFCSP).
Regenerators/repeaters
Test equipment
Passive optical networks
FUNCTIONAL BLOCK DIAGRAM
SLICEP/N
2
VCC
VEE
LOL
CF1
CF2
ADN2807
LOOP
FILTER
2
REFSEL[0..1]
PIN
NIN
2
REFCLKP/N
XO1
/n
FREQUENCY
LOCK
DETECTOR
PHASE
SHIFTER
LOOP
FILTER
PHASE
DET.
QUANTIZER
VCO
XTAL
OSC
XO2
FRACTIONAL
DIVIDER
VREF
REFSEL
LEVEL
DATA
DIVIDER
DETECT
RETIMING
1/2/4/16
3
2
2
THRADJ
SDOUT
DATAOUTP/N
CLKOUTP/N
SEL[0..2]
Figure 1.
Rev. A
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.326.8703
www.analog.com
© 2004 Analog Devices, Inc. All rights reserved.
ADN2807
TABLE OF CONTENTS
Specifications..................................................................................... 3
Absolute Maximum Ratings............................................................ 5
Thermal Characteristics .............................................................. 5
ESD Caution.................................................................................. 5
Pin Configuration and Function Descriptions............................. 6
Definition of Terms.......................................................................... 8
Maximum, Minimum, and Typical Specifications................... 8
Input Sensitivity and Input Overdrive....................................... 8
Single-Ended vs. Differential ...................................................... 8
LOS Response Time ..................................................................... 9
Jitter Specifications....................................................................... 9
Theory of Operation ...................................................................... 10
Functional Description .................................................................. 12
Multirate Clock and Data Recovery......................................... 12
Limiting Amplifier ..................................................................... 12
Slice Adjust.................................................................................. 12
Loss-of-Signal (LOS) Detector ................................................. 12
Reference Clock.......................................................................... 12
Lock Detector Operation .......................................................... 13
Squelch Mode ............................................................................. 14
Test Modes—Bypass and Loop-back....................................... 14
Application Information................................................................ 15
PCB Design Guidelines ............................................................. 15
Choosing AC Coupling Capacitors.......................................... 17
DC-Coupled Application .......................................................... 17
LOL Toggling during Loss of Input Data................................ 17
Outline Dimensions....................................................................... 19
Ordering Guide .......................................................................... 19
REVISION HISTORY
5/04—Data Sheet Changed from Rev. 0 to Rev. A
Changes to Specifications............................................................ 3
Change to Table 7 and Table 8 .................................................. 13
1/04—Revision 0: Initial Version
Rev. A | Page 2 of 20
ADN2807
SPECIFICATIONS
Table 1. TA = TMIN to TMAX, VCC = VMIN to VMAX, VEE = 0 V, CF = 4.7 µF, SLICEP = SLICEN = VCC, unless otherwise noted
Parameter
Conditions
Min
Typ
Max
Unit
QUANTIZER–DC CHARACTERISTICS
Input Voltage Range
Peak-to-Peak Differential Input
Input Common-Mode Level
Differential Input Sensitivity
Input Overdrive
@ PIN or NIN, dc-coupled
0
1.2
2.4
V
V
V
DC-coupled (See Figure 26)
PIN−NIN, ac-coupled1, BER = 1 × 10–10
See Figure 8
0.4
4
2
500
244
10
5
mV p-p
mV p-p
µV
Input Offset
Input RMS Noise
BER = 1 × 10–10
µV rms
QUANTIZER–AC CHARACTERISTICS
Small Signal Gain
Input Resistance
Differential
Differential
54
dB
Ω
pF
ps
100
0.65
10
Input Capacitance
Pulse-Width Distortion2
QUANTIZER SLICE ADJUSTMENT
Gain
SliceP – SliceN = 0.5 V
SliceP – SliceN
@ SliceP or SliceN
0.11
–0.8
1.3
0.20
1.0
0.30
+0.8
VCC
V/V
V
V
Control Voltage Range
Slice Threshold Offset
mV
LEVEL SIGNAL DETECT (SDOUT)
Level Detect Range (See Figure 4)
RTHRESH = 2 kΩ
9.4
2.5
0.7
0.1
13.3
5.3
3.0
18.0
7.6
5.2
5
mV
mV
mV
µs
R
R
THRESH = 20 kΩ
THRESH = 90 kΩ
Response Time
DC-coupled
0.3
Hysteresis (Electrical)
OC-12, PRBS 223
R
R
R
R
THRESH = 2 kΩ
THRESH = 20 kΩ
THRESH = 90 kΩ
THRESH = 90 kΩ @ 25°C
OC-3, PRBS 223
THRESH = 2 kΩ
THRESH = 20 kΩ
THRESH = 90 kΩ
THRESH = 90 k @ 25°C
4.7
1.8
6.4
6.0
6.3
6.9
7.8
10.0
dB
dB
dB
dB
4.8
3.6
8.9
8.5
R
R
R
R
6.2
5.6
5.6
6.6
dB
dB
dB
dB
3.4
9.9
OC-12, PRBS 27
R
R
R
THRESH = 2 kΩ
THRESH = 20 kΩ
THRESH = 90 kΩ
5.7
3.9
3.2
6.6
6.2
6.7
7.8
8.5
9.9
dB
dB
dB
OC-3, PRBS 27
R
R
THRESH = 2 kΩ
THRESH = 20 kΩ
5.4
4.6
3.9
6.6
6.4
6.8
7.7
8.2
9.7
dB
dB
dB
RTHRESH = 90 kΩ
LOSS-OF-LOCK DETECTOR (LOL)
Loss-of-Lock Response Time
POWER SUPPLY VOLTAGE
POWER SUPPLY CURRENT
From fVCO error > 1000 ppm
60
mV
V
3.0
3.3
164
3.6
150
215
mA
Rev. A | Page 3 of 20
ADN2807
Parameter
Conditions
PIN–NIN = 10 mV p-p
OC-12
Min
Typ
Max
Unit
PHASE-LOCKED LOOP CHARACTERISTICS
Jitter Transfer BW
140
48
200
85
kHz
kHz
OC-3
Jitter Peaking
OC-12
OC-3
0.004
0.002
dB
dB
Jitter Generation
OC-12, 12 kHz to 5 MHz
0.003
0.04
0.002
0.04
UI rms
UI p-p
UI rms
UI p-p
0.02
0.02
OC-3, 12 kHz to 1.3 MHz
Jitter Tolerance
OC-12
30 Hz3
300 Hz
25 kHz
250 kHz3
OC-3
100
44
5.8
1.0
UI p-p
UI p-p
UI p-p
UI p-p
30 Hz3
300 Hz3
6500 Hz
65 kHz3
50
UI p-p
UI p-p
UI p-p
UI p-p
23.5
6.0
1.0
CML OUTPUTS (CLKOUTP/N, DATAOUTP/N)
Single-Ended Output Swing
Differential Output Swing
Output High Voltage
Output Low Voltage
Rise Time
VSE (See Figure 7)
VDIFF (See Figure 7)
VOH
VOL, referred to VCC
20% to 80%
80% to 20%
TS (See Figure 3)
OC-12
400
850
488
975
VCC
540
1100
mV
mV
V
V
ps
ps
–0.60
–0.30
150
150
Fall Time
Setup Time
750
3145
ps
ps
OC-3
Hold Time
TH (See Figure 3)
OC-12
750
3150
ps
ps
OC-3
REFCLK DC INPUT CHARACTERISTICS
Input Voltage Range
@ REFCLKP or REFCLKN
0
VCC
V
Peak-to-Peak Differential Input
Common-Mode Level
TEST DATA DC INPUT CHARACTERISTICS4
(TDINP/N)
Peak-to-Peak Differential Input Voltage
LVTTL DC INPUT CHARACTERISTICS
Input High Voltage
100
mV
V
DC-coupled, single-ended
CML inputs
VCC/2
0.8
V
VIH
2.0
V
Input Low Voltage
Input Current
Input Current (SEL0 and SEL1 Only)5
LVTTL DC OUTPUT CHARACTERISTICS
Output High Voltage
VIL
0.8
+5
+50
V
µA
µA
VIN = 0.4 V or VIN = 2.4 V
VIN = 0.4 V or VIN = 2.4 V
–5
–5
VOH, IOH = –2.0 mA
VOL, IOL = +2.0 mA
2.4
V
V
Output Low Voltage
0.4
1PIN and NIN should be driven differentially, ac-coupled for optimum sensitivity.
2PWD measurement made on quantizer outputs in BYPASS mode.
3Jitter tolerance measurements are equipment limited.
4TDINP/N are CML inputs. If the drivers to the TDINP/N inputs are anything other than CML, they must be ac-coupled.
5SEL0 and SEL1 have internal pull-down resistors, causing higher IIH.
Rev. A | Page 4 of 20
ADN2807
ABSOLUTE MAXIMUM RATINGS
Table 2.
THERMAL CHARACTERISTICS
Parameter
Rating
Thermal Resistance
Supply Voltage (VCC)
5.5 V
48-Lead LFCSP, 4-layer board with exposed paddle soldered
to VCC
Minimum Input Voltage (All Inputs)
Maximum Input Voltage (All Inputs)
Maximum Junction Temperature
Storage Temperature
VEE – 0.4 V
VCC + 0.4 V
165°C
θJA = 25°C/W
–65°C to +150°C
Lead Temperature (Soldering 10 sec) 300°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. A | Page 5 of 20
ADN2807
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
THRADJ
VCC
1
2
3
4
5
6
7
8
9
36VCC
35VCC
34VEE
33VEE
32 SEL0
31 NC
30 SEL1
29VEE
28VCC
27VEE
26VCC
25 CF2
PIN 1
INDICATOR
VEE
VREF
PIN
NIN
SLICEP
SLICEN
VEE
LOL 10
XO1 11
XO2 12
ADN2807
TOPVIEW
Figure 2. Pin Configuration
Table 3. Pin Function Descriptions
Pin No.
1
2, 26, 28, Pad
Mnemonic
THRADJ
VCC
Type1 Description
AI
P
LOS Threshold Setting Resistor.
Analog Supply.
3, 9, 16, 19,
VEE
P
Ground.
22, 27, 29, 33,
34, 42, 43, 46
4
5
VREF
PIN
AO
AI
Internal VREF Voltage. Decouple to GND with a 0.1 µF capacitor.
Differential Data Input.
6
NIN
AI
Differential Data Input.
7
8
SLICEP
SLICEN
LOL
XO1
XO2
REFCLKN
REFCLKP
REFSEL
TDINP
TDINN
VCC
AI
AI
DO
AO
AO
DI
DI
DI
AI
AI
P
AO
DI
DI
AO
DI
Differential Slice Level Adjust Input.
Differential Slice Level Adjust Input.
Loss-of-Lock Indicator. LVTTL active high.
Crystal Oscillator.
Crystal Oscillator.
Differential REFCLK Input. LVTTL, LVCMOS, LVPECL, LVDS (LVPECL, LVDS only at 155.52 MHz).
Differential REFCLK Input. LVTTL, LVCMOS, LVPECL, LVDS (LVPECL, LVDS only at 155.52 MHz).
Reference Source Select. 0 = on-chip oscillator with external crystal. 1 = external clock source, LVTTL.
Differential Test Data Input. CML.
Differential Test Data Input. CML.
Digital Supply.
10
11
12
13
14
15
17
18
20, 47
21
23
24
25
30
31
32
35, 36
37
38
39
40
41
44
45
48
CF1
Frequency Loop Capacitor.
REFSEL1
REFSEL0
CF2
SEL1
NC
Reference Frequency Select (See Table 6) LVTTL.
Reference Frequency Select (See Table 6) LVTTL.
Frequency Loop Capacitor.
Data Rate Select (See Table 5) LVTTL.
No Connect.
SEL0
VCC
DI
P
Data Rate Select (See Table 5) LVTTL.
Output Driver Supply.
DATAOUTN
DATAOUTP
SQUELCH
CLKOUTN
CLKOUTP
BYPASS
SDOUT
LOOPEN
DO
DO
DI
DO
DO
DI
Differential Retimed Data Output. CML.
Differential Retimed Data Output. CML.
Disable Clock and Data Outputs. Active high. LVTTL.
Differential Recovered Clock Output. CML.
Differential Recovered Clock Output. CML.
Bypass CDR Mode. Active high. LVTTL.
Loss-of-Signal Detect Output. Active high. LVTTL.
Enable Test Data Inputs. Active high. LVTTL.
DO
DI
1Type: P = Power, AI = Analog Input, AO = Analog Output, DI = Digital Input, DO = Digital Output
Rev. A | Page 6 of 20
ADN2807
CLKOUTP
T
T
H
S
DATAOUTP/N
Figure 3. Output Timing
18
16
14
12
10
8
THRADJ RESISTOR VS. LOSTRIP POINT
6
4
2
0
0
10
20
30
40
50
60
70
80
90
100
RESISTANCE (kΩ)
Figure 4. LOS Comparator Trip Point Programming
10
9
8
7
6
5
4
3
2
1
0
18
16
14
12
10
8
6
4
2
0
0
1
2
3
4
5
6
7
8
9
10
0
1
2
3
4
5
6
7
8
9
10
HYSTERESIS (dB)
HYSTERESIS (dB)
Figure 5. LOS Hysteresis OC-3, −40°C, 3.6 V,
223 –1 PRBS Input Pattern, RTH = 90 kΩ
Figure 6. LOS Hysteresis OC-12, −40°C, 3.6 V,
223 –1 PRBS Input Pattern, RTH = 90 kΩ
OUTP
V
V
CML
SE
OUTN
OUTP–OUTN
V
SE
V
DIFF
0V
Figure 7. Single-Ended vs. Differential Output Specifications
Rev. A | Page 7 of 20
ADN2807
DEFINITION OF TERMS
MAXIMUM, MINIMUM, AND TYPICAL
SPECIFICATIONS
SINGLE-ENDED VS. DIFFERENTIAL
AC coupling is typically used to drive the inputs to the
quantizer. The inputs are internally dc-biased to a common-
mode potential of ~0.6 V. Driving the ADN2807 single-ended
and observing the quantizer input with an oscilloscope probe at
the point indicated in Figure 9 shows a binary signal with
average value equal to the common-mode potential and
instantaneous values both above and below the average value. It
is convenient to measure the peak-to-peak amplitude of this
signal and call the minimum required value the quantizer
sensitivity. Referring to Figure 8, since both positive and
negative offsets need to be accommodated, the sensitivity is
twice the overdrive.
Specifications for every parameter are derived from statistical
analyses of data taken on multiple devices from multiple wafer
lots. Typical specifications are the mean of the distribution of
the data for that parameter. If a parameter has a maximum (or a
minimum) value, that value is calculated by adding to (or
subtracting from) the mean six times the standard deviation of
the distribution. This procedure is intended to tolerate pro-
duction variations. If the mean shifts by 1.5 standard deviations,
the remaining 4.5 standard deviations still provide a failure rate
of only 3.4 parts per million. For all tested parameters, the test
limits are guardbanded to account for tester variation, and
therefore guarantee that no device is shipped outside of data
sheet specifications.
10mV p-p
VREF
INPUT SENSITIVITY AND INPUT OVERDRIVE
SCOPE
PROBE
ADN2807
Sensitivity and overdrive specifications for the quantizer involve
offset voltage, gain, and noise. The relationship between the
logic output of the quantizer and the analog voltage input is
shown in Figure 8. For sufficiently large positive input voltage,
the output is always Logic 1; similarly for negative inputs, the
output is always Logic 0. However, the transitions between
output Logic Levels 1 and 0 are not at precisely defined input
voltage levels, but occur over a range of input voltages. Within
this zone of confusion, the output may be either 1 or 0, or it may
even fail to attain a valid logic state. The width of this zone is
determined by the input voltage noise of the quantizer. The
center of the zone of confusion is the quantizer input offset
voltage. Input overdrive is the magnitude of signal required to
guarantee a correct logic level with a 1 × 10–10 confidence level.
PIN
+
QUANTIZER
50Ω 50Ω
VREF
Figure 9. Single-Ended Sensitivity Measurement
5mV p-p
VREF
OUTPUT
SCOPE
PROBE
ADN2807
NOISE
1
PIN
+
QUANTIZER
NIN
0
50Ω 50Ω
VREF
INPUT (V p-p)
OFFSET
OVERDRIVE
SENSITIVITY
(2× OVERDRIVE)
Figure 10. Differential Sensitivity Measurement
Figure 8. Input Sensitivity and Input Overdrive
Driving the ADN2807 differentially (Figure 10), sensitivity
seems to improve by observing the quantizer input with an
oscilloscope probe. This is an illusion caused by the use of a
single-ended probe. A 5 mV p-p signal appears to drive the
ADN2807 quantizer. However, the single-ended probe measures
only half the signal. The true quantizer input signal is twice this
value since the other quantizer input is complementary to the
signal being observed.
Rev. A | Page 8 of 20
ADN2807
LOS RESPONSE TIME
0.1
The LOS response time is the delay between the removal of the
input signal and indication of loss of signal (LOS) at SDOUT.
The ADN2807’s response time is 300 ns typ when the inputs are
dc-coupled. In practice, the time constant of ac coupling at the
quantizer input determines the LOS response time.
SLOPE = –20dB/DECADE
ACCEPTABLE
RANGE
JITTER SPECIFICATIONS
The ADN2807 CDR is designed to achieve the best bit-error-
rate (BER) performance, and has exceeded the jitter transfer,
generation, and tolerance specifications proposed for
SONET/SDH equipment defined in the Telcordia Technologies
specification. Jitter is the dynamic displacement of digital signal
edges from their long-term average positions measured in UI
(unit intervals), where 1 UI = 1 bit period. Jitter on the input
data can cause dynamic phase errors on the recovered clock
sampling edge. Jitter on the recovered clock causes jitter on the
retimed data. The following sections briefly summarize the
specifications of the jitter generation, transfer, and tolerance in
accordance with the Telcordia document (GR-253-CORE, Issue
3, September 2000) for the optical interface at the equipment
level, and the ADN2807 performance with respect to those
specifications.
fC
JITTER FREQUENCY (kHz)
Figure 11. Jitter Transfer Curve
Jitter Tolerance
The jitter tolerance is defined as the peak-to-peak amplitude of
the sinusoidal jitter applied on the input signal that causes a
1 dB power penalty. This is a stress test intended to ensure that
no additional penalty is incurred under the operating
conditions (Figure 12).
15
SLOPE = –20dB/DECADE
Jitter Generation
The jitter generation specification limits the amount of jitter
that can be generated by the device with no jitter and wander
applied at the input.
1.5
Jitter Transfer
0.15
The jitter transfer function is the ratio of the jitter on the output
signal to the jitter applied on the input signal versus the
frequency. This parameter measures the limited amount of jitter
on an input signal that can be transferred to the output signal
(Figure 11).
f
0
f
1
f
2
f
3
f4
JITTER FREQUENCY (Hz)
Figure 12. SONET Jitter Tolerance Mask
Table 4. Jitter Transfer and Tolerance: SONET Specifications vs. ADN2807
Jitter Transfer
Jitter Tolerance
SONET
ADN2807 Implementation
Mask Corner
Frequency (kHz)
SONET Spec ADN2807 Implementation
Rate
OC-12 500 kHz
OC-3 130 kHz
Spec (fC) (kHz)
Margin
ADN2807 (UI p-p)
(UI p-p)
Margin2
6.67
140
48
3.6
2.7
250 kHz
65 kHz
4.8 MHz
600 kHz
0.15
0.15
1.0
1.0
6.67
2 Jitter tolerance measurements are limited by test equipment capabilities.
Rev. A | Page 9 of 20
ADN2807
THEORY OF OPERATION
psh
e(s)
The ADN2807 is a delay-locked and phase-locked loop circuit
for clock recovery and data retiming from an NRZ encoded
data stream. The phase of the input data signal is tracked by two
separate feedback loops that share a common control voltage. A
high speed delay-locked loop path uses a voltage controlled
phase shifter to track the high frequency components of the
input jitter. A separate phase control loop, comprised of the
VCO, tracks the low frequency components of the input jitter.
The initial frequency of the VCO is set by a third loop, which
compares the VCO frequency with the reference frequency and
sets the coarse tuning voltage. The jitter tracking phase-locked
loop controls the VCO by the fine tuning control. The delay-
and phase-locked loops together track the phase of the input
data signal. For example, when the clock lags input data, the
phase detector drives the VCO to a higher frequency and also
increases the delay through the phase shifter. Both of these
actions serve to reduce the phase error between the clock and
data. The faster clock picks up phase while the delayed data
loses phase. Since the loop filter is an integrator, the static phase
error will be driven to zero.
X(s)
INPUT
DATA
o/s
d/sc
1/n
Z(s)
RECOVERED
CLOCK
JITTERTRANSFER FUNCTION
d = PHASE DETECTOR GAIN
o = VCO GAIN
c = LOOP INTEGRATOR
psh = PHASE SHIFTER GAIN
n = DIVIDE RATIO
Z(s)
X(s)
1
=
cn
do
n psh
2
s
+ s
+1
o
TRACKING ERRORTRANSFER FUNCTION
2
e(s)
X(s)
s
=
d psh
do
cn
2
s
+ s
+
c
Figure 13. PLL/DLL Architecture
The error transfer, e(s)/X(s), has the same high-pass form as an
ordinary phase-locked loop. This transfer function is free to be
optimized to give excellent wideband jitter accommodation
since the jitter transfer function, Z(s)/X(s), provides the narrow-
band jitter filtering. See Table 4 for error transfer bandwidths
and jitter transfer bandwidths at the various data rates. The
delay-locked and phase-locked loops contribute to overall jitter
accommodation. At low frequencies of input jitter on the data
signal, the integrator in the loop filter provides high gain to
track large jitter amplitudes with small phase error. In this case,
the VCO is frequency modulated, and jitter is tracked as in an
ordinary phase-locked loop. The amount of low frequency jitter
that can be tracked is a function of the VCO tuning range. A
wider tuning range gives larger accommodation of low
frequency jitter. The internal loop control voltage remains small
for small phase errors, so the phase shifter remains close to the
center of its range and thus contributes little to the low
frequency jitter accommodation.
Another view of the circuit is that the phase shifter implements
the zero required for the frequency compensation of a second-
order phase-locked loop. This zero is placed in the feedback
path and, therefore, does not appear in the closed-loop transfer
function. Jitter peaking in a conventional second-order phase-
locked loop is caused by the presence of this zero in the closed-
loop transfer function. Since this circuit has no zero in the
closed-loop transfer, jitter peaking is minimized.
The delay- and phase-locked loops together simultaneously
provide wideband jitter accommodation and narrow-band jitter
filtering. The linearized block diagram in Figure 13 shows that
the jitter transfer function, Z(s)/X(s), is a second-order low-pass
providing excellent filtering. Note that the jitter transfer has no
zero, unlike an ordinary second-order phase-locked loop. This
means the main PLL loop has low jitter peaking (Figure 14),
which makes this circuit ideal for signal regenerator
applications where jitter peaking in a cascade of regenerators
can contribute to hazardous jitter accumulation.
Rev. A | Page 10 of 20
ADN2807
the eye opening of the input data, the static phase error, and the
residual loop jitter generation. The jitter accommodation is
roughly 0.5 UI in this region. The corner frequency between the
declining slope and the flat region is the closed loop bandwidth
of the delay-locked loop, which is roughly 5 MHz for OC-12
data rates and 600 kHz for OC-3 data rates.
At medium jitter frequencies, the gain and tuning range of the
VCO are not large enough to track the input jitter. In this case,
the VCO control voltage becomes large and saturates, and the
VCO frequency dwells at one or the other extreme of its tuning
range. The size of the VCO tuning range, therefore, has only a
small affect on the jitter accommodation. The delay-locked loop
control voltage is now larger; therefore, the phase shifter takes
on the burden of tracking the input jitter. The phase shifter
range, in UI, can be seen as a broad plateau on the jitter
tolerance curve. The phase shifter has a minimum range of 2 UI
at all data rates.
JITTER PEAKING
IN ORDINARY PLL
JITTER
GAIN
ADN2807
(dB)
The gain of the loop integrator is small for high jitter
Z(s)
X(s)
frequencies, so larger phase differences are needed to make the
loop control voltage big enough to tune the range of the phase
shifter. Large phase errors at high jitter frequencies cannot be
tolerated. In this region, the gain of the integrator determines
the jitter accommodation. Since the gain of the loop integrator
declines linearly with frequency, jitter accommodation is lower
with higher jitter frequency. At the highest frequencies, the loop
gain is very small, and little tuning of the phase shifter can be
expected. In this case, jitter accommodation is determined by
f
(kHz)
d psh
c
o
n psh
Figure 14. Jitter Response vs. Conventional PLL
Rev. A | Page 11 of 20
ADN2807
FUNCTIONAL DESCRIPTION
Note that it is not expected to use both LOS and slice adjust at
the same time. Systems with optical amplifiers need the slice
adjust to evade ASE. However, a loss-of-signal in an optical link
that uses optical amplifiers causes the optical amplifier output
to be full-scale noise. Under this condition, the LOS would not
detect the failure. In this case, the loss-of-lock signal indicates
the failure because the CDR circuitry is unable to lock onto a
signal that is full-scale noise.
MULTIRATE CLOCK AND DATA RECOVERY
The ADN2807 recovers clock and data from serial bit streams at
OC-3, OC-12 data rates as well as the 15/14 FEC rates. The
output of the 2.5 GHz VCO is divided down in order to support
the lower data rates. The data rate is selected by the SEL[2..0]
inputs (Table 5).
Table 5. Data Rate Selection
SEL[1..0]
Rate
Frequency (MHz)
622.08
155.52
666.51
166.63
REFERENCE CLOCK
00
01
10
11
OC-12
OC-3
OC-12 FEC
OC-3 FEC
There are three options for providing the reference frequency to
the ADN2807: differential clock, single-ended clock, or crystal
oscillator. See Figure 15 to Figure 17 for example configurations.
ADN2807
LIMITING AMPLIFIER
REFCLKP
The limiting amplifier has differential inputs (PIN/NIN) that
are internally terminated with 50 Ω to an on-chip voltage
reference (VREF = 0.6 V typically). These inputs are normally
ac-coupled, although dc-coupling is possible as long as the input
common-mode voltage remains above 0.4 V (Figure 24 to
Figure 26 in the Applications Information section). Input offset
is factory trimmed to achieve better than 4 mV typical
sensitivity with minimal drift. The limiting amplifier can be
driven differentially or single-ended.
BUFFER
REFCLKN
100kΩ 100kΩ
VCC/2
XO1
VCC
CRYSTAL
XO2
OSCILLATOR
VCC
VCC
REFSEL
SLICE ADJUST
The quantizer slicing level can be offset by 100 mV to mitigate
the effect of ASE (amplified spontaneous emission) noise by
applying a differential voltage input of 0.8 V to SLICEP/N
inputs. If no adjustment of the slice level is needed, SLICEP/N
should be tied to VCC.
Figure 15. Differential REFCLK Configuration
ADN2807
VCC
REFCLKP
CLK
OSC
OUT
LOSS-OF-SIGNAL (LOS) DETECTOR
BUFFER
REFCLKN
NC
The receiver front end level signal detect circuit indicates when
the input signal level has fallen below a user adjustable
threshold. The threshold is set with a single external resistor
from THRADJ (Pin 1) to GND. The LOS comparator trip point
versus the resistor value is illustrated in Figure 4 (this is only
valid for SLICEP = SLICEN = VCC). If the input level to the
ADN2807 drops below the programmed LOS threshold,
SDOUT (Pin 45) will indicate the loss-of-signal condition with
a Logic 1. The LOS response time is ~300 ns by design but will
be dominated by the RC time constant in ac-coupled
applications. If the LOS detector is used, the quantizer slice
adjust pins must both be tied to VCC. This is to avoid
interaction with the LOS threshold level.
100kΩ 100kΩ
VCC/2
XO1
VCC
CRYSTAL
OSCILLATOR
XO2
VCC
VCC
REFSEL
Figure 16. Single-Ended REFCLK Configuration
Rev. A | Page 12 of 20
ADN2807
Table 7. Required Crystal Specifications
ADN2807
Parameter
Value
VCC
Mode
Series Resonant
19.44 MHz 100 ppm
100 ppm
100 ppm
100 ppm
REFCLKP
Frequency/Overall Stability
Frequency Accuracy
Temperature Stability
Aging
BUFFER
NC
REFCLKN
100kΩ 100kΩ
VCC/2
ESR
50 Ω max
XO1
XO2
REFSEL must be tied to VCC when the REFCLKN/P inputs are
active or to VEE when the oscillator is used. No connection
between the XO pin and REFCLK input is necessary (Figure 15
to Figure 17). Note that the crystal should operate in series
resonant mode, which renders it insensitive to external
parasitics. No trimming capacitors are required.
CRYSTAL
OSCILLATOR
19.44MHz
REFSEL
Figure 17. Crystal Oscillator Configuration
LOCK DETECTOR OPERATION
The ADN2807 can accept any of the following reference clock
frequencies: 19.44 MHz, 38.88 MHz, and 77.76 MHz at LVTTL/
LVCMOS/LVPECL/LVDS levels, or 155.52 MHz at LVPECL/
LVDS levels via the REFCLKN/P inputs, independent of data
rate. The input buffer accepts any differential signal with a
peak-to-peak differential amplitude of greater than 100 mV
(e.g., LVPECL or LVDS) or a standard single-ended low voltage
TTL input, providing maximum system flexibility. The
appropriate division ratio can be selected using the REFSEL0/1
pins according to Table 6. Phase noise and duty cycle of the
reference clock are not critical, and 100 ppm accuracy is
sufficient.
The lock detector monitors the frequency difference between
the VCO and the reference clock and deasserts the loss-of-lock
signal when the VCO is within 500 ppm of center frequency.
This enables the phase loop, which then maintains phase lock,
unless the frequency error exceeds 0.1%. Should this occur, the
loss-of-lock signal is reasserted and control returns to the
frequency loop, which will reacquire and maintain a stable clock
signal at the output. The frequency loop requires a single
external capacitor between CF1 and CF2. The capacitor
specification is given in Table 8.
Table 8. Recommended CF Capacitor Specification
An on-chip oscillator to be used with an external crystal is also
provided as an alternative to using the REFCLKN/P inputs.
Details of the recommended crystal are given in Table 7.
Parameter
Temperature Range
Capacitance
Leakage
Value
–40°C to +85°C
>3.0 µF
<80 nA
Rating
>6.3 V
Table 6. Reference Frequency Selection
Applied Reference
REFSEL REFSEL[1..0] Frequency (MHz)
1
1
1
1
0
00
01
10
11
XX
19.44
38.88
77.76
155.52
REFCLKP/N Inactive. Use 19.44 MHz
XTAL on Pins XO1, XO2 (Pull REFCLKP
to VCC)
LOL
1
1000
500
0
500
1000
f
ERROR
VCO
(ppm)
Figure 18. Transfer Function of LOL
Rev. A | Page 13 of 20
ADN2807
ADN2807
+
PIN
NIN
0
1
QUANTIZER
CDR
RETIMED
50Ω 50Ω
FROM
QUANTIZER
OUTPUT
DATA
CLK
VREF
1
0
50Ω 50Ω
VCC
TDINP/N
LOOPEN BYPASS DATAOUTP/N
CLKOUTP/N SQUELCH
Figure 19. Test Modes
The loopback mode can be invoked by driving the LOOPEN
pin to a TTL high state, which facilitates system diagnostic
testing. This will connect the test inputs (TDINP/N) to the
clock and data recovery circuit (per Figure 19). The test inputs
have internal 50 Ω terminations and can be left floating when
not in use. TDINP/N are CML inputs and can be dc-coupled
only when being driven by CML outputs. The TDINP/N inputs
must be ac-coupled if driven by anything other than CML
outputs. Bypass and loop-back modes are mutually exclusive;
only one of these modes can be used at any given time. The
ADN2807 is put into an indeterminate state if both BYPASS
and LOOPEN pins are set to Logic 1 at the same time.
SQUELCH MODE
When the squelch input is driven to a TTL high state, both the
clock and data outputs are set to the zero state to suppress
downstream processing. If desired, this pin can be directly
driven by the LOS (loss-of-signal) detector output (SDOUT). If
the squelch function is not required, the pin should be tied to
VEE.
TEST MODES—BYPASS AND LOOP-BACK
When the bypass input is driven to a TTL high state, the
quantizer output is connected directly to the buffers driving the
data out pins, thus bypassing the clock recovery circuit
(Figure 19). This feature can help the system to deal with
nonstandard bit rates.
Rev. A | Page 14 of 20
ADN2807
APPLICATION INFORMATION
PCB DESIGN GUIDELINES
matched in length and that the CLKOUTP/N and
DATAOUTP/N traces are matched in length. All high speed
CML outputs, CLKOUTP/N and DATAOUTP/N, also require
100 Ω back termination chip resistors connected between the
output pin and VCC. These resistors should be placed as close
as possible to the output pins. These 100 Ω resistors are in
parallel with on-chip 100 Ω termination resistors to create a
50 Ω back termination (Figure 21).
Proper RF PCB design techniques must be used for optimal
performance.
Power Supply Connections and Ground Planes
Use of one low impedance ground plane to both analog and
digital grounds is recommended. The VEE pins should be
soldered directly to the ground plane to reduce series
inductance. If the ground plane is an internal plane and
connections to the ground plane are made through vias,
multiple vias may be used in parallel to reduce the series
inductance, especially on Pins 33 and 34, which are the ground
returns for the output buffers.
The high speed inputs, PIN and NIN, are internally terminated
with 50 Ω to an internal reference voltage (Figure 22). A 0.1 µF
capacitor is recommended between VREF (Pin 4) and GND to
provide an ac ground for the inputs.
As with any high speed mixed-signal design, care should be
taken to keep all high speed digital traces away from sensitive
analog nodes.
Use of a 10 µF electrolytic capacitor between VCC and GND is
recommended at the location where the 3.3 V supply enters the
PCB. Use of 0.1 µF and 1 nF ceramic chip capacitors should be
placed between IC power supply VCC and GND as close as
possible to the ADN2807’s VCC pins. Again, if connections to
the supply and ground are made through vias, the use of
multiple vias in parallel will help to reduce series inductance,
especially on Pins 35 and 36, which supply power to the high
speed CLKOUTP/N and DATAOUTP/N output buffers. Refer
to the schematic in Figure 20 for recommended connections.
Soldering Guidelines for Chip Scale Package
The leads on the 48-lead LFCSP are rectangular. The printed
circuit board pad for these should be 0.1 mm longer than the
package lead length and 0.05 mm wider than the package lead
width. The land should be centered on the pad. This ensures
that solder joint size is maximized. The bottom of the LFCSP
has a central exposed pad. The pad on the printed circuit board
should be at least as large as this exposed pad. The user must
connect the exposed pad to analog VCC. If vias are used, they
should be incorporated into the pad at 1.2 mm pitch grid. The
via diameter should be between 0.3 mm and 0.33 mm, and the
via barrel should be plated with 1 oz. copper to plug the via.
Transmission Lines
Use of 50 Ω transmission lines are required for all high
frequency input and output signals to minimize reflections,
including PIN, NIN, CLKOUTP, CLKOUTN, DATAOUTP, and
DATAOUTN (also REFCLKP/N for a 155.52 MHz REFCLK). It
is also recommended that the PIN/NIN input traces are
Rev. A | Page 15 of 20
ADN2807
VCC
50Ω
TRANSMISSION
LINES
4 × 100Ω
CLKOUTP
CLKOUTN
DATAOUTP
DATAOUTN
VCC
µC
10µF
0.1µF
1nF
48 47 46 45 44 43 42 41 40 39 38 37
R
TH
THRADJ
VCC
VCC
36
1
VCC
VCC
VEE
VEE
SEL0
NC
2
35
34
33
32
31
30
29
28
27
26
25
VCC
1nF
0.1µF
0.1µF
1nF
VEE
3
0.1µF
VREF
PIN
4
50Ω
EXPOSED PAD
TIED OFFTO
VCC PLANE
WITH VIAS
µC
NC
µC
5
TIA
NIN
6
SLICEP
SLICEN
VEE
SEL1
VEE
VCC
VEE
VCC
CF2
C
50Ω
IN
7
VCC
8
9
0.1µF
LOL
1nF
0.1µF
1nF
10
11
12
µC
19.44MHz
XO1
VCC
ADN2807
XO2
20 21 22 23 24
13 14 15 16 17 18 19
4.7µF
(SEETABLE8 FOR SPECS)
VCC
0.1µF
1nF
Figure 20. Typical Application Circuit
VCC
ADN2807
VCC
VCC
C
C
IN
50Ω
50Ω
PIN
NIN
V
TERM
TIA
100Ω 100Ω
100Ω 100Ω
IN
50Ω
0.1µF
0.1µF
50Ω
50Ω
50Ω
50Ω
VREF
50Ω
0.1µF
ADN2807
V
TERM
Figure 22. AC-Coupled Input Configuration
Figure 21. AC-Coupled Output Configuration
Rev. A | Page 16 of 20
ADN2807
CHOOSING AC COUPLING CAPACITORS
LOL TOGGLING DURING LOSS OF INPUT DATA
The ac coupling capacitors at the input (PIN, NIN) and output
(DATAOUTP, DATAOUTN) of the ADN2807 must be chosen
so that the device works properly at both OC-3 and OC-12 data
rates. When choosing the capacitors, the time constant formed
with the two 50 Ω resistors in the signal path must be
considered. When a large number of consecutive identical digits
(CIDs) are applied, the capacitor voltage can drop due to
baseline wander (Figure 23), causing pattern dependent jitter
(PDJ). For the ADN2807 to work robustly at both OC-3 and
OC-12, a minimum capacitor of 0.1 µF to PIN/NIN and 0.1 µF
on DATAOUTP/DATAOUTN should be used. This is based on
the assumption that 1000 CIDs must be tolerated, and that the
PDJ should be limited to 0.01 UI p-p.
If the input data stream is lost due to a break in the optical link
(or for any reason), the clock output from the ADN2807 stays
within 1000 ppm of the VCO center frequency as long as there
is a valid reference clock. The LOL pin will toggle at a rate of
several kHz. This is because the LOL pin will toggle between a
Logic 1 and Logic 0 while the frequency loop and phase loop
swap control of the VCO. The chain of events is as follows:
•
•
The ADN2807 is locked to the input data stream; LOL = 0.
The input data stream is lost due to a break in the link. The
VCO frequency drifts until the frequency error is greater
than 1000 ppm. LOL is asserted to a Logic 1 as control of
the VCO is passed back to the frequency loop.
DC-COUPLED APPLICATION
•
The frequency loop pulls the VCO to within 500 ppm of its
center frequency. Control of the VCO is passed back to the
phase loop and LOL is deasserted to Logic 0.
The inputs to the ADN2807 can also be dc-coupled. This may
be necessary in burst mode applications where there are long
periods of CIDs, and where baseline wander cannot be
tolerated. If the inputs to the ADN2807 are dc-coupled, care
must be taken not to violate the input range and common-mode
level requirements of the ADN2807 (Figure 24 to Figure 26). If
dc coupling is required and the output levels of the TIA do not
adhere to the levels shown in Figure 25 and Figure 26, there
must be level shifting and/or an attenuator between the TIA
outputs and the ADN2807 inputs.
•
•
The phase loop tries to acquire, but there is no input data
present so the VCO frequency drifts.
The VCO frequency drifts until the frequency error is
greater than 1000 ppm. LOL is asserted to a Logic 1 as
control of the VCO is passed back to the frequency loop.
This process is repeated until a valid input data stream is
re-established.
ADN2807
C
C
OUT
V1
IN
V2
PIN
NIN
+
DATAOUTP
DATAOUTN
50Ω
V
LIMAMP
CDR
REF
TIA
C
C
OUT
V1b
V2b
50Ω
IN
2
3
4
1
V1
V1b
V2
V
REF
V2b
VTH
V
DIFF
V
= V2–V2b
DIFF
VTH = ADN2807 QUANTIZERTHRESHOLD
NOTES
1. DURING DATA PATTERNS WITH HIGH TRANSITION DENSITY, DIFFERENTIAL DC VOLTAGE AT V1 AND V2 IS 0.
2. WHENTHE OUTPUT OFTHE TIA GOESTO CID, V1 AND V1b ARE DRIVENTO DIFFERENT DC LEVELS. V2 AND V2b
DISCHARGETOTHEV LEVEL,WHICH EFFECTIVELY INTRODUCES A DIFFERENTIAL DC OFFSET ACROSSTHE AC COUPLING CAPACITORS.
REF
3. WHENTHE BURST OF DATA STARTS AGAIN,THE DIFFERENTIAL DC OFFSET ACROSSTHE AC COUPLING CAPACITORS IS APPLIEDTOTHE INPUT LEVELS,
CAUSING A DC SHIFT INTHE DIFFERENTIAL INPUT. THIS SHIFT IS LARGE ENOUGH SUCHTHAT ONE OFTHE STATES, EITHER HIGH OR LOW DEPENDING ON
THE LEVELS OF V1 AND V1bWHENTHE TIAWENTTO CID, IS CANCELLED OUT. THE QUANTIZERWILL NOT RECOGNIZETHIS AS AVALID STATE.
4. THE DC OFFSET SLOWLY DISCHARGES UNTILTHE DIFFERENTIAL INPUTVOLTAGE EXCEEDSTHE SENSITIVITY OFTHE ADN2807.THE QUANTIZER WILL BE
ABLETO RECOGNIZE BOTH HIGH AND LOW STATES ATTHIS POINT.
Figure 23. Example of Baseline Wander
Rev. A | Page 17 of 20
ADN2807
INPUT (V)
VCC
ADN2807
V p-p = PIN – NIN = 2 × V = 2.4V MAX
SE
PIN
50Ω
50Ω
PIN
NIN
TIA
V
= 1.2V MAX
SE
V
= 0.6V
CM
(DC-COUPLED)
50Ω
50Ω
NIN
VREF
0.1µ F
Figure 26. Maximum Allowed DC-Coupled Input Levels
Figure 24. ADN2807 with DC-Coupled Inputs
INPUT (V)
V p-p = PIN – NIN = 2 × V = 10mV AT SENSITIVITY
SE
PIN
NIN
V
= 5mV MIN
SE
V
= 0.4V MIN
CM
(DC-COUPLED)
Figure 25. Minimum Allowed DC-Coupled Input Levels
Rev. A | Page 18 of 20
ADN2807
OUTLINE DIMENSIONS
0.30
0.23
0.18
7.00
BSC SQ
0.60 MAX
0.60 MAX
PIN 1
INDICATOR
37
36
48
1
PIN 1
INDICATOR
5.25
5.10 SQ
4.95
6.75
BSC SQ
TOP
VIEW
BOTTOM
VIEW
0.50
0.40
0.30
25
24
12
13
0.25 MIN
5.50
REF
0.80 MAX
0.65 TYP
1.00
0.85
0.80
ꢀ
12° MAX
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.50 BSC
0.20 REF
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-220-VKKD-2
Figure 27. 48-Lead Lead Frame Chip Scale Package [LFCSP]
7 mm × 7 mm Body (CP-48)
Dimensions shown in millimeters
ORDERING GUIDE
Model
ADN2807ACP
ADN2807ACP-RL
Temperature Range
–40°C to +85°C
–40°C to +85°C
Package Description
48-Lead LFCSP
48-Lead LFCSP
Package Option
CP-48
CP-48
Rev. A | Page 19 of 20
ADN2807
NOTES
©
2004 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D03877–0–5/04(A)
Rev. A | Page 20 of 20
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明