AM1M-0512S-NZ [AIMTEC]

1 Watt | DC-DC Converter; 1瓦| DC-DC转换器


型号：	AM1M-0512S-NZ
厂家：	AIMTEC
描述：	1 Watt \| DC-DC Converter 1瓦\| DC-DC转换器转换器 DC-DC转换器
文件：	总3页 (文件大小：200K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

Series AM1M-NZ

1 Watt | DC-DC Converter

FEATURES:

• Low Profile DIP14 case

• 1.5KVDC Isolation

• Pin-out compatible with DCP01 Series

• Short circuit protection

• Operating Temperature: -40°C to +85°C

• High Power Density

• RoHS Compliant

Models

Single output

Input Voltage

Output Voltage

Output Current

Isolation

(VDC)

1500

Efficiency

Model

(V)

4.5-5.5

(V)

max (mA)

(%)

AM1M-0505S-NZ

AM1M-0509S-NZ

AM1M-0512S-NZ

AM1M-0515S-NZ

AM1M-1205S-NZ

AM1M-1209S-NZ

AM1M-1212S-NZ

AM1M-1215S-NZ

200

111

1500

4.5-5.5

10.8-13.2

200

111

NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at

rated output load unless otherwise specified.

Input Specifications

Parameters

Nominal

Typical

4.5-5.5

10.8-13.2

Maximum

Units

Voltage range

VDC

Isolation Specifications

Parameters

Tested I/O voltage

Resistance

Conditions

60 Sec

Typical

Rated

1500

Units

VDC

MOhm

500Vdc

1000

Output Specifications

Parameters

Conditions

Typical

Maximum

Units

Voltage accuracy

See tolerance envelope graph

Short Circuit protection

Short circuit restart

Continuous

Auto-Recovery

Line voltage regulation (Single)

Load voltage regulation (Single)

Temperature coefficient

Ripple & Noise

For Vin change of 1%

10% to 100% load

Nominal input,100% full load

20MHz Bandwidth

±1.2

12.8

0.03

% of Vin

%/^oC

mV p-p

% of Max

Minimum Load Current

NOTE: It is not recommended to have the outputs connected in parallel

www.aimtec.com

F 051e R8.B

Tel: +1 514 620 2722

1 of 3

Toll free: + 1 888 9 AIMTEC

(924 6832)

North America only

Series AM1M-NZ

1 Watt | DC-DC Converter

General Specifications

Parameters

Switching frequency

Operating temperature

Storage temperature

Maximum case temperature

Cooling

Conditions

100% load

Typical

100

-40 to + 85

-55 to +125

Maximum

Units

KHz

^oC

100

^oC

Free Air Convection

Humidity

Case material

Weight

Dimensions (L x W x H)

MTBF

% RH

Epoxy Resin(UL94-V0)

1.4

0.77 x 0.28 x 0.18 inches 19.50 x 6.60 x 4.50 mm

>1,500,000 hours (MIL-HDBK -217F, Ground Benign, t=+25^oC)

Maximum Soldering Temperature

1.5mm from case for 10 seconds

260

^oC

Pin Out Specifications

Single

+Vin

-Vin

-Vout

+Vout

NC: not connected

Dimensions

Typical Characteristics

Top View

19.50

(0.77)

2.54

(0.10)

Tolerance Envelope Graph

Typical Load Line

+10%

+5%

6.60

(0.28)

7.62

(0.30)

Bottom View

+2.5%

-2.5%

-7.5%

Front View

7.62

(0.30)

Side View

4.50

5.0

(0.18)

(0.197)

100%

10%

50%

3.25

(0.602)

Output Current(%)

www.aimtec.com

F 051e R8.B

Tel: +1 514 620 2722

2 of 3

Toll free: + 1 888 9 AIMTEC

(924 6832)

North America only

Series AM1M-NZ

1 Watt | DC-DC Converter

Minimum Load Requirement

In order for this module to operate efficiently and reliably a minimum load of no less than 10% of its maximum needs to be

maintained at all times during operation.

NOTE: this converter should never be operated under no load. If it is required to operate the converter with less than 10%

load it is recommended to install a resistor in parallel with the application load to draw additional current from the converter

output to maintain the minimum load condition, or use a converter rated at a lower power.

Single Output

+Vout

+ Vin

Cin

Cout

- Vin

Recommended Filter Circuit

- Vin

If it is required to decrease the input/output ripple, an “LC” filtering network may be connected to the input and output of the

converter, see above.

It should be noted that the inductance and the resonant frequency of the “LC” filtering network should differ from the DC/DC

converter switching frequency to avoid mutual interference.

The capacitance of the output filter capacitor must not exceed the values in the Table below to avoid startup problems and

ensure safe and reliable operation.

It’s not recommended to connect any external capacitor in the application field when output loading is less than 0.5 watt.

External Capacitor Tables

Input Capacitor (Cin)

Output Capacitor (Cout)

Vin

(VDC)

Cin

(uF)

4.7

Vout

(VDC)

Cout

(uF)

2.2

4.7

2.2

NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled

by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the

date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%,

nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components

and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This

product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate

specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com.

www.aimtec.com

F 051e R8.B

Tel: +1 514 620 2722

3 of 3

Toll free: + 1 888 9 AIMTEC

(924 6832)

North America only

相关型号：