TK63429B6GHB-C [AKM]
Fixed Positive LDO Regulator;型号: | TK63429B6GHB-C |
厂家: | ASAHI KASEI MICROSYSTEMS |
描述: | Fixed Positive LDO Regulator 输出元件 调节器 |
文件: | 总29页 (文件大小:628K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
[TK635xxAB6]
TK635xxAB6
Auto Discharge, Ultrafast Response, High RR, Low Noise
200mA CMOS LDO Regulator IC
1-. DESCRIPTION
4-. PIN CONFIGURATION
The TK635xxAB6 is a CMOS LDO regulator. The
package is the very small 4-bump flip chip.
The IC is designed for portable applications with space
requirements.
The IC can supply 200mA output current.
The IC does not require a noise-bypass capacitor.
The IC offer ultra fast transient response.
The IC includes an auto-discharge function.
The output voltage is internally fixed from 1.5V to 4.2V.
FC-4
VIn
B2
A2
B1
VOut
GND
VCont
A1
A1 mark
2-. FEATURES
(Top View)
Auto discharge function
Ultra small package: FC-4
No noise bypass capacitor required
Ultrafast transient response
High ripple rejection
5-. BLOCK DIAGRAM
VIn
VOut
Low noise
B2
B1
Thermal and over current protection
High maximum load current
On/Off control
VRef
CIn
COut
High accuracy
Thermal &
Over Current
Protection
On/Off
Control
3-. APPLICATIONS
VCont
GND
Mobile communication
A2
A1
AP-MS0035-E-00
- 1 -
2011/02
[TK635xxAB6]
6-. ORDERING INFORMATION
T K 6 3 5
A B 6 G H B - C
Voltage Code
(Refer to the following table)
Operating Temp. Range Code
C : C Rank(standard)
Package Code
B6 : FC-4
Tape/Reel Code
B : Normal type for FC
Environment Code
GH : Lead Free +
Halogen Free
Output Voltage
Voltage Code
Output Voltage
Voltage Code
Output Voltage
Voltage Code
40
1.5V
15
2.9V
29
4.0V
1.8V
2.5V
2.6V
2.7V
2.8V
18
25
26
27
28
3.0V
3.1V
3.2V
3.3V
3.5V
30
31
32
33
35
*If you need a voltage other than the value listed in the above table, please contact Asahi Kasei Microdevices.
7-. ABSOLUTE MAXIMUM RATINGS
Ta=25C
Parameter
Absolute Maximum Ratings
Input Voltage
Symbol
Rating
Units
Conditions
VIn,MAX
VOut,MAX
VCont,MAX
Tstg
-0.3 ~ 6.0
-0.3 ~ VIn+0.3
-0.3 ~ 6.0
V
V
Output pin Voltage
Control pin Voltage
V
Storage Temperature Range
-55 ~ 150
C
Internal Limited Tj=150°C *,
Power Dissipation
PD
360
mW
When mounted on a PCB
Operating Condition
Operational Temperature Range
TOP
VOP
-40 ~ 85
2.0 ~ 6.0
C
Operational Voltage Range
V
* PD must be decreased at the rate of 2.9mW for operation above 25C.
The maximum ratings are the absolute limitation values with the possibility of the IC being damaged.
If the operation exceeds any of these standards, quality cannot be guaranteed.
AP-MS0035-E-00
- 2 -
2011/02
[TK635xxAB6]
8-. ELECTRICAL CHARACTERISTICS
The parameters with min. or max. values will be guaranteed at Ta=Tj=25C with test when manufacturing or SQC
(Statistical Quality Control) methods. The operation between -40 ~ 85C is guaranteed by design.
VIn=VOut,TYP+1V, VCont=1.2V, Ta=Tj=25°C
Value
TYP
Parameter
Symbol
Units
Conditions
MIN
MAX
Output Voltage
VOut
LinReg
LoaReg
VDrop
IOut,MAX
IQ
V
IOut=5mA
Refer to TABLE 1
Line Regulation
-
0.0
4.0
mV
mV
mV
mA
µA
µA
µA
VIn=1V
Load Regulation
Refer to TABLE 1
Refer to TABLE 1
Refer to TABLE 1
Refer to TABLE 1
VOut=VOut,TYP0.9
IOut=0mA, VCont=VIn
VCont=0V
Dropout Voltage *1
Maximum Load Current *2
Quiescent Current
Standby Current
210
350
40
-
80
0.1
100
-
-
-
-
-
IStandby
IGND
0.01
50
GND Pin Current
Discharge Resistance
IOut=50mA, VCont=VIn
VIn=5V, VOut=0.1V, VCont=0V
RDis
20
Control Terminal
Control Current
ICont
-
1.2
-
0.2
0.4
-
µA
V
VCont=1.2V
-
-
VOut On state
VOut Off state
Control Voltage
VCont
0.2
V
Reference Value
Output Voltage / Temp.
Output Noise Voltage
(TK63528AB6)
-
-
100
45
-
-
ppm/°C IOut=5mA
VOut/Ta
COut=1.0µF, IOut=30mA,
BPF=400Hz~80kHz
VNoise
µVrms
dB
Ripple Rejection
COut=1.0µF,
RR
tr
-
-
75
65
-
-
(TK63528AB6)
IOut=10mA, f=1kHz
COut=1.0µF, IOut=30mA
Rise Time
VCont: Pulse Wave (100Hz),
µs
(TK63528AB6)
VCont On VOut95% point
*1: For VOut 2.0V, no regulations.
*2: The maximum output current is limited by power dissipation.
The maximum load current is the current where the output voltage decreases to 90% by increasing the output current at
Tj=25°C, compared to the output voltage specified at VIn=VOut,TYP+1V. The maximum load current indicates the current
at which over current protection turn on.
For all output voltage products, the maximum output current for normal operation without operating any protection is
200mA. Accordingly, LoaReg and VDrop are specified on the condition that IOut is less than 200mA.
General Note
Parameters with only typical values are just reference. (Not guaranteed)
The noise level is dependent on the output voltage, the capacitance and capacitor characteristics.
AP-MS0035-E-00
- 3 -
2011/02
[TK635xxAB6]
TABLE 1.
Load Regulation
Dropout Voltage
Output Voltage
IOut=5 ~ 100mA IOut=5 ~ 200mA IOut=100mA
IOut=200mA
Part Number
MIN TYP MAX TYP MAX TYP MAX TYP MAX TYP MAX
V
V
V
mV
3
mV
12
12
20
20
20
20
20
20
24
24
24
24
28
mV
6
mV
24
28
36
40
40
40
44
44
44
48
48
52
60
mV
-
mV
-
mV
-
mV
-
TK63515AB6
TK63518AB6
TK63525AB6
TK63526AB6
TK63527AB6
TK63528AB6
TK63529AB6
TK63530AB6
TK63531AB6
TK63532AB6
TK63533AB6
TK63535AB6
TK63540AB6
1.475 1.500 1.525
1.775 1.800 1.825
2.475 2.500 2.525
2.574 2.600 2.626
2.673 2.700 2.727
2.772 2.800 2.828
2.871 2.900 2.929
2.970 3.000 3.030
3.069 3.100 3.131
3.168 3.200 3.232
3.267 3.300 3.333
3.465 3.500 3.535
3.960 4.000 4.040
3
7
-
-
-
-
5
9
95
90
90
90
85
85
85
80
80
80
75
145
140
140
140
135
135
135
130
130
130
120
185
180
175
175
170
165
165
160
160
155
150
310
305
295
295
285
280
280
275
275
265
255
5
10
10
10
11
11
11
12
12
13
15
5
5
5
5
6
6
6
6
7
Notice.
Please contact your authorized Asahi Kasei Microdevices representative for voltage availability.
AP-MS0035-E-00
- 4 -
2011/02
[TK635xxAB6]
9-. TEST CIRCUIT
Test circuit for electrical characteristic
IIn
_
CIn
=1.0F
A
VIn
VOut
VCont GND
ICont
VCont
Notice.
COut
=1.0F
The limit value of electrical characteristics is applied when
CIn=1.0F(Ceramic), COut=1.0F(Ceramic).
_
V
VIn=
VOut,TYP+1.0V
IOut
=5mA
VOut
_
A
VIn
VOut
VCont GND
ICont
VCont
VOut vs VIn
VDrop vs IOut
VOut vs IOut
VOut vs IOut
VOut vs Ta
VDrop vs Ta
CIn
=1.0F
COut
=1.0F
_
V
VIn
IOut
VOut
_
A
IOut,MAX vs Ta
ICont vs VCont , VOut vs VCont
ICont vs Ta
VCont vs Ta
VNoise vs VIn
VNoise vs IOut
VNoise vs VOut
VNoise vs Frequency
IIn
_
CIn
=1.0F
A
VIn
VOut
VCont GND
ICont
VCont
IQ vs VIn
IStandby vs VIn
IQ vs Ta
Open
COut
=1.0F
VIn=
VOut,TYP+1.0V
_
A
VIn
VOut
VCont GND
ICont IGND
VCont
IGND vs IOut
IGND vs Ta
CIn
=1.0F
COut
=1.0F
VIn=
IOut
_
A
_
A
VOut,TYP+1.0V
AP-MS0035-E-00
- 5 -
2011/02
[TK635xxAB6]
VIn=
VOut,TYP+1.5V
VIn
VOut
RR vs VIn
RR vs Frequency
RR vs Frequency
Vripple
500mVP-P
=
COut
=1.0F
VCont GND
IOut
=10mA
VCont
=1.2V
VOut,TYP+2V
VIn
VOut
Line Transient
Load Transient
On/Off Transient
COut
=1.0F
VOut,TYP+1V
VCont GND
_
V
IOut
=5mA
VOut
VOut
VOut
VCont
=1.2V
VIn
VOut
CIn
=1.0F
COut
=1.0F
VCont GND
_
V
VIn=
VOut,TYP+1.0V
IOut
VCont
=1.2V
VIn
VOut
CIn
=1.0F
COut
=1.0F
VCont GND
_
V
VIn=
IOut=
VOut,TYP+1.0V
0mA or
30mA
VCont
=0V 1.2V
AP-MS0035-E-00
- 6 -
2011/02
[TK635xxAB6]
10-. TYPICAL CHARACTERISTICS
10-1-. DC CHARACTERISTICS
VOut vs VIn (TK63515AB6)
VOut vs VIn (TK63515AB6)
10
40
20
IOut=5mA
5
IOut=0, 5, 50, 100, 150, 200mA
0
-5
0
-20
-10
-15
-20
-25
-30
-40
-60
-80
-100
0
1
2
3
4
4
4
5
6
6
6
-100 -50
0
50 100 150 200 250 300
VIn-VOut [mV]
VIn [V]
VOut vs VIn (TK63528AB6)
VOut vs VIn (TK63528AB6)
10
5
40
IOut=5mA
20
IOut=0, 5, 50, 100, 150, 200mA
0
0
-20
-5
-10
-15
-20
-25
-30
-40
-60
-80
-100
0
1
2
3
5
-100 -50
0
50 100 150 200 250 300
VIn-VOut [mV]
VIn [V]
VOut vs VIn (TK63542AB6)
VOut vs VIn (TK63542AB6)
10
5
40
20
IOut=5mA
IOut=0, 5, 50, 100, 150, 200mA
0
0
-20
-5
-10
-15
-20
-25
-30
-40
-60
-80
-100
0
1
2
3
5
-100 -50
0
50 100 150 200 250 300
VIn-VOut [mV]
VIn [V]
AP-MS0035-E-00
- 7 -
2011/02
[TK635xxAB6]
VOut vs IOut (TK63515AB6)
2
1.5
1
0.5
0
0
100
200
300
300
300
400
400
400
500
IOut [mA]
VDrop vs IOut (TK63528AB6)
VOut vs IOut (TK63528AB6)
0
4
-100
-200
-300
-400
3
2
1
0
0
50
100
150
200
0
100
200
IOut [mA]
500
IOut [mA]
VDrop vs IOut (TK63542AB6)
VOut vs IOut (TK63542AB6)
0
6
5
4
3
2
1
0
-100
-200
-300
-400
0
50
100
150
200
0
100
200
IOut [mA]
500
IOut [mA]
AP-MS0035-E-00
- 8 -
2011/02
[TK635xxAB6]
VOut vs IOut (TK63515AB6)
VOut vs Ta (TK63515AB6)
10
100
80
0
-10
-20
-30
-40
60
40
20
0
-20
-40
-60
-80
-100
0
50
100
150
150
150
200
200
200
-50
-25
0
25
50
50
50
75
100
100
100
IOut [mA]
Ta [°C]
VOut vs IOut (TK63528AB6)
VOut vs Ta (TK63528AB6)
10
100
80
0
-10
-20
-30
-40
60
40
20
0
-20
-40
-60
-80
-100
0
50
100
-50
-25
0
25
75
IOut [mA]
Ta [°C]
VOut vs IOut (TK63542AB6)
VOut vs Ta (TK63542AB6)
10
100
80
0
-10
-20
-30
-40
60
40
20
0
-20
-40
-60
-80
-100
0
50
100
-50
-25
0
25
75
IOut [mA]
Ta [°C]
AP-MS0035-E-00
- 9 -
2011/02
[TK635xxAB6]
IOut,MAX vs Ta (TK63515AB6)
400
300
200
-50
-25
0
25
50
50
50
75
100
100
100
Ta [°C]
VDrop vs Ta (TK63528AB6)
IOut,MAX vs Ta (TK63528AB6)
0
-50
400
-100
-150
-200
-250
-300
-350
-400
100mA
200mA
300
200
-50
-25
0
25
50
75
100
-50
-25
0
25
75
Ta [°C]
Ta [°C]
VDrop vs Ta (TK63542AB6)
IOut,MAX vs Ta (TK63542AB6)
0
-50
400
-100
-150
-200
-250
-300
-350
-400
100mA
200mA
300
200
-50
-25
0
25
50
75
100
-50
-25
0
25
75
Ta [°C]
Ta [°C]
AP-MS0035-E-00
- 10 -
2011/02
[TK635xxAB6]
IQ vs VIn (TK63515AB6)
IStandby vs VIn (TK63515AB6)
100
10
9
8
7
6
5
4
3
2
1
0
VCont=0V
VCont=VIn
80
60
40
20
0
0
1
2
3
4
5
6
0
1
2
3
4
4
4
5
6
6
6
VIn [V]
VIn [V]
IQ vs VIn (TK63528AB6)
IStandby vs VIn (TK63528AB6)
10
9
8
7
6
5
4
3
2
1
0
100
VCont=VIn
VCont=0V
80
60
40
20
0
0
1
2
3
4
5
6
0
1
2
3
5
VIn [V]
VIn [V]
IQ vs VIn (TK63542AB6)
IStandby vs VIn (TK63542AB6)
100
10
9
8
7
6
5
4
3
2
1
0
VCont=0V
VCont=VIn
80
60
40
20
0
0
1
2
3
4
5
6
0
1
2
3
5
VIn [V]
VIn [V]
AP-MS0035-E-00
- 11 -
2011/02
[TK635xxAB6]
IGND vs IOut (TK63515AB6)
IQ vs Ta (TK63515AB6)
200
180
160
140
120
100
80
100
90
80
70
60
50
40
30
20
10
0
VCont=VIn
VCont=VIn
60
40
20
0
0
50
100
150
150
150
200
-50
-25
0
25
50
50
50
75
100
IOut [mA]
Ta [°C]
IGND vs IOut (TK63528AB6)
IQ vs Ta (TK63528AB6)
200
180
160
140
120
100
80
100
90
80
70
60
50
40
30
20
10
0
VCont=VIn
VCont=VIn
60
40
20
0
0
50
100
200
-50
-25
0
25
75
100
IOut [mA]
Ta [°C]
IGND vs IOut (TK63542AB6)
IQ vs Ta (TK63542AB6)
200
180
160
140
120
100
80
100
90
80
70
60
50
40
30
20
10
0
VCont=VIn
VCont=VIn
60
40
20
0
0
50
100
200
-50
-25
0
25
75
100
IOut [mA]
Ta [°C]
AP-MS0035-E-00
- 12 -
2011/02
[TK635xxAB6]
ICont vs VCont, VOut vs VCont (TK63515AB6)
IGND vs Ta (TK63515AB6)
100
90
80
70
60
50
40
30
20
10
0
1
0.75
0.5
2
IOut=50mA
VOut
1.5
1
0.25
0
0.5
0
ICont
-50
-25
0
25
50
50
50
75
100
0
0.5
1
1.5
2
2
2
Ta [°C]
VCont [V]
IGND vs Ta (TK63528AB6)
ICont vs VCont, VOut vs VCont (TK63528AB6)
100
90
80
70
60
50
40
30
20
10
0
1
4
3
2
1
0
IOut=50mA
VOut
0.75
0.5
0.25
0
ICont
0
0.5
1
1.5
-50
-25
0
25
75
100
VCont [V]
Ta [°C]
IGND vs Ta (TK63542AB6)
ICont vs VCont, VOut vs VCont (TK63542AB6)
100
90
80
70
60
50
40
30
20
10
0
1
8
6
4
2
0
IOut=50mA
0.75
VOut
0.5
0.25
0
ICont
-50
-25
0
25
75
100
0
0.5
1
1.5
Ta [°C]
VCont [V]
AP-MS0035-E-00
- 13 -
2011/02
[TK635xxAB6]
VCont vs Ta (TK63515AB6)
ICont vs Ta (TK635xxAB6)
1.4
1.2
1
1
VCont=1.2V
0.75
0.5
0.25
0
0.8
0.6
0.4
0.2
0
-50
-25
0
25
50
75
100
-50
-25
0
25
50
50
50
75
75
75
100
100
100
Ta [°C]
Ta [°C]
VCont vs Ta (TK63528AB6)
1.4
1.2
1
0.8
0.6
0.4
0.2
0
-50
-25
0
25
Ta [°C]
VCont vs Ta (TK63542AB6)
1.4
1.2
1
0.8
0.6
0.4
0.2
0
-50
-25
0
25
Ta [°C]
AP-MS0035-E-00
- 14 -
2011/02
[TK635xxAB6]
10-2-. AC CHARACTERISTICS
RR vs VIn (TK63515AB6)
RR vs Frequency (TK63515AB6)
0
0
-10
-20
IOut=10mA
COut=0.68, 1.0, 2.2F(cer.)
Vp-p=0.1V, Frequency=1kHz
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-30
-40
-50
-60
-70
-80
-90
-100
IOut=10mA
50mA
100mA
150mA
200mA
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
3.5
2.5
100
1k
10k
100k
1M
1M
1M
VIn-VOut [V]
Frequency [Hz]
RR vs VIn (TK63528AB6)
RR vs Frequency (TK63528AB6)
0
0
-10
-20
IOut=10mA
COut=0.68, 1.0, 2.2F(cer.)
Vp-p=0.1V, Frequency=1kHz
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-30
-40
-50
-60
-70
-80
-90
-100
IOut=10mA
50mA
100mA
150mA
200mA
0
0.5
1
1.5
2
2.5
3
100
1k
10k
100k
VIn-VOut [V]
Frequency [Hz]
RR vs VIn (TK63542AB6)
RR vs Frequency (TK63542AB6)
0
0
-10
-20
IOut=10mA
COut=0.68, 1.0, 2.2F(cer.)
Vp-p=0.1V, Frequency=1kHz
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
IOut=10mA
-30
-40
-50
-60
-70
-80
-90
-100
50mA
100mA
150mA
200mA
0
0.5
1
1.5
2
100
1k
10k
100k
VIn-VOut [V]
Frequency [Hz]
AP-MS0035-E-00
- 15 -
2011/02
[TK635xxAB6]
VNoise vs VIn (TK63515AB6)
100
90
80
70
60
50
40
30
20
10
0
The ripple rejection (RR) characteristic depends on the
characteristic and the capacitance value of the capacitor
connected to the output side. The RR characteristic of
50kHz or more varies greatly with the capacitor on the
output side and PCB pattern. If necessary, please confirm
stability of your design.
IOut=30mA
1
2
3
4
5
6
6
6
VIn [V]
VNoise vs VIn (TK63528AB6)
100
90
80
70
60
50
40
30
20
10
0
IOut=30mA
2.5
3
3.5
4
4.5
5
5.5
VIn [V]
VNoise vs VIn (TK63542AB6)
100
90
80
70
60
50
40
30
20
10
0
IOut=30mA
4
4.5
5
5.5
VIn [V]
AP-MS0035-E-00
- 16 -
2011/02
[TK635xxAB6]
VNoise vs IOut (TK63515AB6)
VNoise vs VOut (TK635xxAB6)
100
90
80
70
60
50
40
30
20
10
0
100
90
80
70
60
50
40
30
20
10
0
0
50
100
150
150
150
200
200
200
1
1.5
2
2.5
3
3.5
4
4.5
IOut [mA]
VOut [V]
VNoise vs IOut (TK63528AB6)
100
90
80
70
60
50
40
30
20
10
0
0
50
100
IOut [mA]
VNoise vs IOut (TK63542AB6)
100
90
80
70
60
50
40
30
20
10
0
0
50
100
IOut [mA]
AP-MS0035-E-00
- 17 -
2011/02
[TK635xxAB6]
VNoise vs Frequency (TK63515AB6)
10
IOut=10mA
1
0.1
0.01
10
100
1k
10k
100k
Frequency [Hz]
VNoise vs Frequency (TK63528AB6)
10
IOut=10mA
1
0.1
0.01
10
100
1k
10k
100k
Frequency [Hz]
VNoise vs Frequency (TK63542AB6)
10
IOut=10mA
1
0.1
0.01
10
100
1k
10k
100k
Frequency [Hz]
AP-MS0035-E-00
- 18 -
2011/02
[TK635xxAB6]
10-3-. TRANSIENT CHARACTERISTICS
Line Transient (TK63515AB6)
Load Transient (IOut=5100 or 200mA) (TK63515AB6)
100 or 200mA
3.5V
5mA
IOut
VIn
2.5V
IOut=30, 100, 200mA
V
VOut
Out
100mA
200mA
10mV/div
10mV/div
10mV/div
50mV/div
0
0
0
0
0
20sec/div
Time
40sec/div
Time
Line Transient (TK63528AB6)
Load Transient (IOut=5100 or 200mA) (TK63528AB6)
100 or 200mA
4.8V
5mA
IOut
VIn
3.8V
IOut=30, 100, 200mA
VOut
VOut
100mA
50mV/div
0
0
0
0
200mA
0
20sec/div
Time
40sec/div
Time
Line Transient (TK63542AB6)
Load Transient (IOut=5100 or 200mA) (TK63542AB6)
100 or 200mA
6.2V
5mA
IOut
VIn
5.2V
IOut=30, 100, 200mA
V
VOut
Out
100mA
50mV/div
0
0
0
0
200mA
0
20sec/div
Time
40sec/div
Time
AP-MS0035-E-00
- 19 -
2011/02
[TK635xxAB6]
Load Transient (IOut=1501mA) (TK63515AB6)
Load Transient (IOut=1150mA) (TK63515AB6)
IOut : tR=1 sec
IOut : tF=1 sec
150mA
150mA
1mA
IOut
IOut
1mA
VOut
VOut
50mV/div
0
0
50mV/div
20sec/div
Time
20sec/div
Time
Load Transient (IOut=1150mA) (TK63528AB6)
Load Transient (IOut=1501mA) (TK63528AB6)
IOut : tR=1 sec
IOut : tF=1 sec
150mA
150mA
1mA
IOut
IOut
1mA
VOut
VOut
50mV/div
50mV/div
0
0
20sec/div
20sec/div
Time
Time
Load Transient (IOut=1150mA) (TK63542AB6)
Load Transient (IOut=1501mA) (TK63542AB6)
IOut : tF=1 sec
IOut : tR=1 sec
150mA
150mA
1mA
IOut
IOut
1mA
VOut
VOut
50mV/div
50mV/div
0
0
20sec/div
Time
20sec/div
Time
AP-MS0035-E-00
- 20 -
2011/02
[TK635xxAB6]
On/Off Transient (VCont=01.2V) (TK63515AB6)
On/Off Transient (VCont=1.20V) (TK63515AB6)
VCont
VCont
1V/div
1V/div
0
0
COut=1.0, 2.2F
COut=1.0, 2.2F
VOut
VOut
0
0.5V/div
0.5V/div
0
IIn
IIn
0
IOut=30mA
IOut=0mA
100mA/div
200mA/div
0
10sec/div
40µsec/div
Time
Time
On/Off Transient (VCont=01.2V) (TK63528AB6)
On/Off Transient (VCont=1.20V) (TK63528AB6)
VCont
VCont
1V/div
1V/div
0
0
COut=1.0, 2.2F
COut=1.0, 2.2F
VOut
VOut
0
1V/div
1V/div
0
IIn
0
IIn
IOut=30mA
100mA/div
200mA/div
IOut=0mA
0
20sec/div
40µsec/div
Time
Time
On/Off Transient (VCont=01.2V) (TK63542AB6)
On/Off Transient (VCont=1.20V) (TK63542AB6)
VCont
VCont
1V/div
1V/div
0
0
COut=1.0, 2.2F
COut=1.0, 2.2F
VOut
0
2V/div
VOut
0
2V/div
IIn
0
IIn
0
IOut=30mA
100mA/div
200mA/div
IOut=0mA
20sec/div
40µsec/div
Time
Time
AP-MS0035-E-00
- 21 -
2011/02
[TK635xxAB6]
11-. PIN DESCRIPTION
Pin No. Pin Description
Internal Equivalent Circuit
Description
GND Terminal
A1
GND
Control Terminal
ESD
protection
VCont > 1.2V : On
VCont < 0.2V : Off
VCont
A2
VCont
The pull-down resistor (about 6.5M) is built-in.
6.5M
Output Terminal
VIn
VOut
B1
B2
VOut
ESD
protection
On/Off
Control
VIn
Input Terminal
AP-MS0035-E-00
- 22 -
2011/02
[TK635xxAB6]
Fig12-2: Output Current vs Stable Operation Area
12-. APPLICATIONS INFORMATION
12-1-. Stability
TK63515AB6
-40~+85ºC
100
10
Linear regulators require input and output capacitors in
order to maintain the regulator's loop stability. If 0.68µF
capacitors are connected to the input side and the output
side, the IC provides stable operation. However, it is
recommended to use as large a value capacitor as is
practical. The output noise and the ripple noise decrease
as the value of the capacitor increases.
A recommended value of the application is as follows.
CIn0.68µF, COut0.68µF
It is not possible to determine this indiscriminately.
Please confirm the stability in your design.
Unstable Area
Stable Area
COut=0.68µF
1
0.1
0.01
0
0
0
50
100
150
200
200
200
I
Out [mA]
Fig12-1: Capacitor in the application
VIn
VOut
TK635xx
TK63528AB6
-40~+85ºC
CIn0.68µF
COut0.68µF
100
10
VCont
Unstable Area
1
Stable Area
COut=0.68µF
0.1
0.01
50
100
150
I
Out [mA]
TK63542AB6
-40~+85ºC
100
10
Unstable Area
1
Stable Area
COut=0.68µF
0.1
0.01
50
100
150
I
Out [mA]
AP-MS0035-E-00
- 23 -
2011/02
[TK635xxAB6]
Fig.12-2 shows the stable operation area of output
current and the equivalent series resistance (ESR) with a
ceramic capacitor of 0.68µF. ESR of the output capacitor
must be in the stable operation area. Please select the best
output capacitor according to the voltage and current
used. The stability of the regulator improves as the value
of the output side capacitor increases (the stable
operation area extends.) Please use as large a value
capacitor as is practical.
For evaluation
Kyocera : CM105B684K10A , CM105B105K06A ,
CM21B225K10A
Fig12-3: ex. Ceramic Capacitance vs Voltage,
Temperature
Capacitance vs Voltage
100
90
B Curve
80
70
60
50
F Curve
4
0
2
6
8
10
12
Bias Voltage(V)
Capacitance vs Temperature
100
90
80
70
60
50
B Curve
F Curve
-50 -25
0
25
50
75
100
Ta(°C)
Generally, a ceramic capacitor has both a temperature
characteristic and a voltage characteristic. Please consider
both characteristics when selecting the part. The B curves
are the recommended characteristics.
AP-MS0035-E-00
- 24 -
2011/02
[TK635xxAB6]
How to determine the thermal resistance when
mounted on PCB
12-2-. Layout
The thermal resistance when mounted is expressed as
follows:
図12-4: Layout example
Tj=jaPD+Ta
VCont
GND
VIn
Tj of IC is set around 150C. PD is the value when the
thermal sensor is activated.
If the ambient temperature is 25C, then:
150=jaPD+25
ja=125/PD (C /mW)
PD is easily calculated.
A simple way to determine PD is to calculate VInIIn
when the output side is shorted. Input current gradually
falls as output voltage rises after working thermal
shutdown. You should use the value when thermal
equilibrium is reached.
GND
GND
(Top View)
VOut
PCB Material: Glass epoxy
Size: 7mm×8mm×0.8mm
Please do derating with 2.9mW/C at PD=360mW, and
25C or more. Thermal resistance (ja) is=250C/W.
Fig12-6: How to determine DPD
PD (mW)
2
PD
Fig12-5: Derating Curve
Pd(mW)
DPD
3
360
5
-2.9mW/°C
4
25
50
75
100 125 150
Ta (°C)
Procedure (When mounted on PCB.)
1. Find PD (VInIIn when the output side is short-
circuited).
25
50
100
(85°C)
150°C
2. Plot PD against 25C.
The package loss is limited at the temperature that the
internal temperature sensor works (about 150C).
Therefore, the package loss is assumed to be an internal
limitation. There is no heat radiation characteristic of the
package unit assumed because of its small size. Heat is
carried away from the device by being mounted on the
PCB. This value is directly effected by the material and
the copper pattern etc. of the PCB. The losses are
approximately 360mW. Enduring these losses becomes
possible in a lot of applications operating at 25C.
3. Connect PD to the point corresponding to the 150C
with a straight line.
4. In design, take a vertical line from the maximum
operating temperature (e.g., 75C) to the derating
curve.
5. Read off the value of PD against the point at which the
vertical line intersects the derating curve. This is taken
as the maximum power dissipation DPd.
6. DPD (VIn,MAXVOut)=IOut (at 75C)
The maximum output current at the highest operating
temperature will be IOut DPD (VIn,MAX-VOut).
Please use the device at low temperature with better
radiation. The lower temperature provides better quality.
The overheating protection circuit operates when the
junction temperature reaches 150C (this happens when
the regulator is dissipating excessive power, outside
temperature is high, or heat radiation is bad). The output
current and the output voltage will drop when the
protection circuit operates. However, operation begins
again as soon as the output voltage drops and the
temperature of the chip decreases.
AP-MS0035-E-00
- 25 -
2011/02
[TK635xxAB6]
12-3-. On/Off Control
12-4-. Influence by Light
It is recommended to turn the regulator Off when the
circuit following the regulator is not operating. A design
with little electric power loss can be implemented. We
recommend the use of the On/Off control of the regulator
without using a high side switch to provide an output
from the regulator. A highly accurate output voltage with
low voltage drop is obtained.
When TK635xxAB6 (FC-4) is exposed to strong light,
the electrical characteristics change. Please confirm the
influence by light in your design.
Because the control current is small, it is possible to
control it directly by CMOS logic.
Fig12-7: The use of On/Off control
Vsat
REG
On/Off Cont.
Control Terminal Voltage ((VCont
)
On/Off State
VCont > 1.2V
On
VCont < 0.2V
Off
Parallel Connected On/Off Control
Fig12-8: The example of parallel connected IC
VOut
VIn
4.2V
2.8V
1.5V
TK63542
TK63528
TK63515
On/Off
Cont.
The above figure is multiple regulators being controlled
by a single On/Off control signal. There is concern of
overheating, because the power loss of the low voltage
side IC (TK63515AB6) is large. The series resistor (R) is
put in the input line of the low output voltage regulator in
order to prevent over-dissipation. The voltage dropped
across the resistor reduces the large input-to-output
voltage across the regulator, reducing the power
dissipation in the device. When the thermal sensor works,
a decrease of the output voltage, oscillation, etc. may be
observed.
AP-MS0035-E-00
- 26 -
2011/02
[TK635xxAB6]
12-5-. Definition of term
Characteristics
Protections
Over Current Sensor
The over current sensor protects the device when there is
excessive output current. It also protects the device if the
output is accidentally connected to ground.
Output Voltage (VOut
)
The output voltage is specified with VIn=(VOutTYP+1V)
and IOut=5mA.
Maximum Output Current (IOut, MAX
)
Thermal Sensor
The rated output current is specified under the condition
where the output voltage drops to 90% of the value
specified with IOut=5mA. The input voltage is set to
VOutTYP+1V and the current is pulsed to minimize
temperature effect.
The thermal sensor protects the device in case the
junction temperature exceeds the safe value (Tj=150C).
This temperature rise can be caused by external heat,
excessive power dissipation caused by large input to
output voltage drops, or excessive output current. The
regulator will shut off when the temperature exceeds the
safe value. As the junction temperatures decrease, the
regulator will begin to operate again. Under sustained
fault conditions, the regulator output will oscillate as the
device turns off then resets. Damage may occur to the
device under extreme fault.
Dropout Voltage (VDrop
)
The dropout voltage is the difference between the input
voltage and the output voltage at which point the
regulator starts to fall out of regulation. Below this value,
the output voltage will fall as the input voltage is reduced.
It is dependent upon the output voltage, the load current,
and the junction temperature.
Please prevent the loss of the regulator when this
protection operates, by reducing the input voltage or
providing better heat efficiency.
Line Regulation (LinReg)
Line regulation is the ability of the regulator to maintain a
constant output voltage as the input voltage changes. The
line regulation is specified as the input voltage is changed
ESD
MM : 200pF 0 150V or more
HBM : 100pF 1.5k 2000V or more
from VIn=VOut,TYP+1V to VIn=6V. It is
measurement to minimize temperature effect.
a pulse
Load Regulation (LoaReg)
Load regulation is the ability of the regulator to maintain
a constant output voltage as the load current changes. It is
a pulsed measurement to minimize temperature effects
with the input voltage set to VIn=VOut,TYP+1V. The load
regulation is specified under an output current step
condition of 1mA to 50mA.
Ripple Rejection (RR)
Ripple rejection is the ability of the regulator to attenuate
the ripple content of the input voltage at the output. It is
specified with 500mVP-P, 1kHz super-imposed on the
input voltage, where VIn=VOut,TYP+1.5V. Ripple rejection
is the ratio of the ripple content of the output vs. input and
is expressed in dB.
Standby Current (IStandby
)
Standby current is the current which flows into the
regulator when the output is turned off by the control
function (VCont=0V).
AP-MS0035-E-00
- 27 -
2011/02
[TK635xxAB6]
13-. PACKAGE OUTLINE
4-bump flip chip
: FC-4
Mark
±0.03
4- 0.30
M
0.05
B
0.5
A
Lot No.
A1 Pin Mark
±0.03
0.96
0.05
0.5
Reference Mount Pad
4- 0.275
Unit : mm
Package Structure and Others
Base Material
: Si
Mark Method
: Laser
Terminal Material : Lead Free Solder Bump
Solder Composition : Sn-2.5Ag
Country of Origin : Japan
Marking
Part Number
Marking Code
Part Number
Marking Code
Part Number
Marking Code
TK63515AB6
TK63518AB6
TK63525AB6
TK63526AB6
TK63527AB6
TK63528AB6
L15
TK63529AB6
L29
L30
L31
L32
L33
L35
TK63540AB6
L40
L18
L25
L26
L27
L28
TK63530AB6
TK63531AB6
TK63532AB6
TK63533AB6
TK63535AB6
AP-MS0035-E-00
- 28 -
2011/02
[TK635xxAB6]
IMPORTANT NOTICE
These products and their specifications are subject to change without notice.
When you consider any use or application of these products, please make inquiries the sales office of
Asahi Kasei Microdevices Corporation (AKM) or authorized distributors as to current status of the
products.
Descriptions of external circuits, application circuits, software and other related information contained
in this document are provided only to illustrate the operation and application examples of the
semiconductor products. You are fully responsible for the incorporation of these external circuits,
application circuits, software and other related information in the design of your equipments. AKM
assumes no responsibility for any losses incurred by you or third parties arising from the use of these
information herein. AKM assumes no liability for infringement of any patent, intellectual property, or
other rights in the application or use of such information contained herein.
Any export of these products, or devices or systems containing them, may require an export license or
other official approval under the law and regulations of the country of export pertaining to customs
and tariffs, currency exchange, or strategic materials.
AKM products are neither intended nor authorized for use as critical componentsNote1) in any safety,
life support, or other hazard related device or systemNote2), and AKM assumes no responsibility for
such use, except for the use approved with the express written consent by Representative Director of
AKM. As used here:
Note1) A critical component is one whose failure to function or perform may reasonably be expected to
result, whether directly or indirectly, in the loss of the safety or effectiveness of the device or system
containing it, and which must therefore meet very high standards of performance and reliability.
Note2) A hazard related device or system is one designed or intended for life support or maintenance of
safety or for applications in medicine, aerospace, nuclear energy, or other fields, in which its failure to
function or perform may reasonably be expected to result in loss of life or in significant injury or damage to
person or property.
It is the responsibility of the buyer or distributor of AKM products, who distributes, disposes of, or
otherwise places the product with a third party, to notify such third party in advance of the above
content and conditions, and the buyer or distributor agrees to assume any and all responsibility and
liability for and hold AKM harmless from any and all claims arising from the use of said product in
the absence of such notification.
AP-MS0035-E-00
- 29 -
2011/02
相关型号:
TK63431AMFG0L-C
Fixed Positive LDO Regulator, 3.1V, 0.275V Dropout, CMOS, PDSO4, 1.20 X 1.40 MM, LEAD FREE, PLASTIC, SON-4
AKM
TK63431AMFG0L-C
Fixed Positive LDO Regulator, 3.1V, 0.275V Dropout, CMOS, PDSO4, 1.20 X 1.40 MM, LEAD FREE, PLASTIC, SON-4
TOKO
©2020 ICPDF网 联系我们和版权申明