AM29LV008BB-120EK_技术文档

Am29LV008B

Data Sheet

The Am29LV008B is not offered for new designs. Please contact a Spansion representative for alter-

nates.

The following document contains information on Spansion memory products. Although the document

is marked with the name of the company that originally developed the specification, Spansion will

continue to offer these products to existing customers.

Continuity of Specifications

There is no change to this data sheet as a result of offering the device as a Spansion product. Any

changes that have been made are the result of normal data sheet improvement and are noted in the

document revision summary, where supported. Future routine revisions will occur when appro and

changes will be noted in a revision summary.

Continuity of Ordering Part Numbers

Spansion continues to support existing part numbers beginning with “Am” and “MBM”. To order these

products, please use only the Ordering Part Numbers listed in this document.

For More Information

Please contact your local sales office for additional information about Spansion memory solutions.

Publication Number 21524 Revision D Amendment 6 Issue Date October 11, 2006

THIS PAGE LEFT INTENTIONALLY BLANK.

DATA SHEET

Am29LV008B

8 Megabit (1 M x 8-Bit)

CMOS 3.0 Volt-only Boot Sector Flash Memory

The Am29LV008B is not offered for new designs. Please contact a Spansion representative for alternates.

DISTINCTIVE CHARACTERISTICS

■ Single power supply operation

■ Top or bottom boot block configurations

available

— Full voltage range: 2.7 to 3.6 volt read and write

operations for battery-powered applications

■ Embedded Algorithms

— Regulated voltage range: 3.0 to 3.6 volt read and

write operations and for compatibility with high

performance 3.3 volt microprocessors

— Embedded Erase algorithm automatically

preprograms and erases the entire chip or any

combination of designated sectors

■ Manufactured on 0.32 µm process technology

— Embedded Program algorithm automatically

writes and verifies data at specified addresses

— Compatible with 0.5 µm Am29LV008 device

■ Minimum 1,000,000 write cycle guarantee per sector

■ 20-year data retention at 125°C

— Reliable operation for the life of the system

■ Package option

■ High performance

— Full voltage range: access times as fast as 90 ns

— Regulated voltage range: access times as fast as

70 ns

— 40-pin TSOP

■ Ultra low power consumption (typical values at 5

MHz)

■ Compatibility with JEDEC standards

— 200 nA Automatic Sleep mode current

— 200 nA standby mode current

— 7 mA read current

— Pinout and software compatible with single-

power supply Flash

— Superior inadvertent write protection

— 15 mA program/erase current

■ Data# Polling and toggle bits

■ Flexible sector architecture

— Provides a software method of detecting program

or erase operation completion

— One 16 Kbyte, two 8 Kbyte, one 32 Kbyte, and

fifteen 64 Kbyte sectors

■ Ready/Busy# pin (RY/BY#)

— Supports full chip erase

— Provides a hardware method of detecting

program or erase cycle completion

— Sector Protection features:

A hardware method of locking a sector to prevent

any program or erase operations within that

sector

■ Erase Suspend/Erase Resume

— Suspends an erase operation to read data from,

or program data to, a sector that is not being

erased, then resumes the erase operation

Sectors can be locked in-system or via

programming equipment

■ Hardware reset pin (RESET#)

Temporary Sector Unprotect feature allows code

changes in previously locked sectors

— Hardware method to reset the device to reading

array data

■ Unlock Bypass Program Command

— Reduces overall programming time when issuing

multiple program command sequences

This Data Sheet states AMD’s current technical specifications regarding the Products described herein. This Data

Sheet may be revised by subsequent versions or modifications due to changes in technical specifications.

Publication# 21524 Rev: D Amendment: 6

Issue Date: October 11, 2006

D A T A S H E E T

GENERAL DESCRIPTION

The Am29LV008B is an 8 Mbit, 3.0 volt-only Flash

memory organized as 1,048,576 bytes. The device is

offered in a 40-pin TSOP package. The byte-wide (x8)

data appears on DQ7–DQ0. This device requires only a

single, 3.0 volt VCC supply to perform read, program,

and erase operations. A standard EPROM programmer

can also be used to program and erase the device.

programmed) before executing the erase operation.

During erase, the device automatically times the erase

pulse widths and verifies proper cell margin.

The host system can detect whether a program or

erase operation is complete by observing the RY/BY#

pin, or by reading the DQ7 (Data# Polling) and DQ6

(toggle) status bits. After a program or erase cycle has

been completed, the device is ready to read array data

or accept another command.

This device is manufactured using AMD’s 0.32 µm

process technology, and offers all the features and ben-

efits of the Am29LV008, which was manufactured using

0.5 µm process technology. In addition, the

Am29LV008B features unlock bypass programming

and in-system sector protection/unprotection.

The sector erase architecture allows memory sectors

to be erased and reprogrammed without affecting the

data contents of other sectors. The device is fully

erased when shipped from the factory.

The standard device offers access times of 70, 90, and

120 ns, allowing high speed microprocessors to

operate without wait states. To eliminate bus contention

the device has separate chip enable (CE#), write

enable (WE#) and output enable (OE#) controls.

Hardware data protection measures include a low

V

detector that automatically inhibits write opera-

CC

tions during power transitions. The hardware sector

protection feature disables both program and erase

operations in any combination of the sectors of

memory. This can be achieved in-system or via pro-

gramming equipment.

The device requires only a single 3.0 volt power

supply for both read and write functions. Internally

generated and regulated voltages are provided for the

program and erase operations.

The Erase Suspend feature enables the user to put

erase on hold for any period of time to read data from,

or program data to, any sector that is not selected for

erasure. True background erase can thus be achieved.

The device is entirely command set compatible with the

JEDEC single-power-supply Flash standard. Com-

mands are written to the command register using

standard microprocessor write timings. Register con-

tents serve as input to an internal state-machine that

controls the erase and programming circuitry. Write

cycles also internally latch addresses and data needed

for the programming and erase operations. Reading

data out of the device is similar to reading from other

Flash or EPROM devices.

The hardware RESET# pin terminates any operation

in progress and resets the internal state machine to

reading array data. The RESET# pin may be tied to the

system reset circuitry. A system reset would thus also

reset the device, enabling the system microprocessor

to read the boot-up firmware from the Flash memory.

The device offers two power-saving features. When

addresses have been stable for a specified amount of

time, the device enters the automatic sleep mode.

The system can also place the device into the standby

mode. Power consumption is greatly reduced in both

these modes.

Device programming occurs by executing the program

command sequence. This initiates the Embedded

Program algorithm—an internal algorithm that auto-

matically times the program pulse widths and verifies

proper cell margin. The Unlock Bypass mode facili-

tates faster programming times by requiring only two

write cycles to program data instead of four.

AMD’s Flash technology combines years of Flash

memory manufacturing experience to produce the

highest levels of quality, reliability and cost effectiveness.

The device electrically erases all bits within a sector

simultaneously via Fowler-Nordheim tunneling. The

data is programmed using hot electron injection.

Device erasure occurs by executing the erase

command sequence. This initiates the Embedded

Erase algorithm—an internal algorithm that automati-

cally preprograms the array (if it is not already

4

Am29LV008B

21524D6 October 11, 2006

D A T A S H E E T

TABLE OF CONTENTS

Product Selector Guide . . . . . . . . . . . . . . . . . . . . .6

Connection Diagrams . . . . . . . . . . . . . . . . . . . . . . .7

Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . .7

Logic Symbol . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Ordering Information . . . . . . . . . . . . . . . . . . . . . . .8

Device Bus Operations . . . . . . . . . . . . . . . . . . . . . .9

Table 1. Am29LV008B Device Bus Operations ................................9

Requirements for Reading Array Data ..................................... 9

Writing Commands/Command Sequences .............................. 9

Program and Erase Operation Status .................................... 10

Standby Mode ........................................................................ 10

Automatic Sleep Mode ........................................................... 10

RESET#: Hardware Reset Pin ............................................... 10

Output Disable Mode .............................................................. 10

Table 2. Am29LV008BT Top Boot Sector Address Table ...............11

Table 3. Am29LV008BB Bottom Boot Sector Address Table .........11

Autoselect Mode ..................................................................... 12

Table 4. Am29LV008B Autoselect Codes (High Voltage Method) ..12

Sector Protection/Unprotection ............................................... 12

Figure 1. In-System Sector Protect/Sector Unprotect Algorithms... 13

Temporary Sector Unprotect .................................................. 14

Figure 2. Temporary Sector Unprotect Operation........................... 14

Hardware Data Protection ...................................................... 14

DQ5: Exceeded Timing Limits ................................................ 22

DQ3: Sector Erase Timer ....................................................... 22

Table 6. Write Operation Status ..................................................... 23

Absolute Maximum Ratings . . . . . . . . . . . . . . . . 24

Figure 7. Maximum Negative Overshoot Waveform ...................... 24

Figure 8. Maximum Positive Overshoot Waveform........................ 24

Operating Ranges. . . . . . . . . . . . . . . . . . . . . . . . . 24

DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 25

Figure 9. I_CC1Current vs. Time (Showing Active and

Automatic Sleep Currents)............................................................. 26

Figure 10. Typical I_CC1vs. Frequency ........................................... 26

Test Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Figure 11. Test Setup..................................................................... 27

Table 7. Test Specifications ........................................................... 27

Figure 12. Input Waveforms and Measurement Levels ................. 27

AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 28

Read Operations .................................................................... 28

Figure 13. Read Operations Timings ............................................. 28

Hardware Reset (RESET#) .................................................... 29

Figure 14. RESET# Timings .......................................................... 29

Erase/Program Operations ..................................................... 30

Figure 15. Program Operation Timings.......................................... 31

Figure 16. Chip/Sector Erase Operation Timings .......................... 32

Figure 17. Data# Polling Timings (During Embedded Algorithms). 33

Figure 18. Toggle Bit Timings (During Embedded Algorithms)...... 33

Figure 19. DQ2 vs. DQ6................................................................. 34

Temporary Sector Unprotect .................................................. 34

Figure 20. Temporary Sector Unprotect Timing Diagram .............. 34

Figure 21. Sector Protect/Unprotect Timing Diagram .................... 35

Alternate CE# Controlled Erase/Program Operations ............ 36

Figure 22. Alternate CE# Controlled Write Operation Timings ...... 37

Erase and Programming Performance . . . . . . . 38

Latchup Characteristics. . . . . . . . . . . . . . . . . . . . 38

TSOP Pin Capacitance . . . . . . . . . . . . . . . . . . . . . 38

Data Retention. . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Physical Dimensions . . . . . . . . . . . . . . . . . . . . . . 39

TS 040—40-Pin Standard TSOP ............................................ 39

Revision Summary . . . . . . . . . . . . . . . . . . . . . . . . 40

Revision A (October 1997) ..................................................... 40

Revision B (January 1998) ..................................................... 40

Revision B+1 (March 1998) .................................................... 40

Revision C (January 1999) ..................................................... 40

Revision D (November 19, 1999) ........................................... 40

Revision D+1 (August 14, 2000) ............................................. 40

Revision D+2 (November 10, 2000) ....................................... 40

Revision D+3 (June 11, 2004) ................................................ 40

Revision D4 (February 21, 2006) ............................................ 40

Revision D5 (September 12, 2006) ........................................ 40

Low V Write Inhibit .............................................................. 14

CC

Write Pulse “Glitch” Protection ............................................... 14

Logical Inhibit .......................................................................... 14

Power-Up Write Inhibit ............................................................ 14

Command Definitions . . . . . . . . . . . . . . . . . . . . . .15

Reading Array Data ................................................................ 15

Reset Command ..................................................................... 15

Autoselect Command Sequence ............................................ 15

Byte Program Command Sequence ....................................... 15

Unlock Bypass Command Sequence ..................................... 16

Figure 3. Program Operation .......................................................... 16

Chip Erase Command Sequence ........................................... 16

Sector Erase Command Sequence ........................................ 17

Erase Suspend/Erase Resume Commands ........................... 17

Figure 4. Erase Operation............................................................... 18

Command Definitions ............................................................. 19

Table 5. Am29LV008B Command Definitions .................................19

Write Operation Status . . . . . . . . . . . . . . . . . . . . .20

DQ7: Data# Polling ................................................................. 20

Figure 5. Data# Polling Algorithm ................................................... 20

RY/BY#: Ready/Busy# ........................................................... 21

DQ6: Toggle Bit I .................................................................... 21

DQ2: Toggle Bit II ................................................................... 21

Reading Toggle Bits DQ6/DQ2 .............................................. 21

Figure 6. Toggle Bit Algorithm......................................................... 22

October 11, 2006 21524D6

Am29LV008B

5

D A T A S H E E T

PRODUCT SELECTOR GUIDE

Family Part Number

Am29LV008B

Regulated Voltage Range: V_CC=3.0–3.6 V

Full Voltage Range: V_CC= 2.7–3.6 V

Max access time, ns (t_ACC

Max CE# access time, ns (t_CE

Max OE# access time, ns (t_OE

-70R

Speed Options

-90

90

35

-120

120

50

)

70

30

)

Note: See “AC Characteristics” for full specifications.

BLOCK DIAGRAM

DQ0–DQ7

RY/BY#

V_CC

Sector Switches

V_SS

Erase Voltage

Generator

Input/Output

Buffers

RESET#

State

Control

WE#

Command

Register

PGM Voltage

Generator

Data

Latch

Chip Enable

Output Enable

Logic

STB

CE#

OE#

Y-Decoder

Y-Gating

STB

V_CCDetector

Timer

Cell Matrix

X-Decoder

A0–A19

6

Am29LV008B

21524D6 October 11, 2006

D A T A S H E E T

CONNECTION DIAGRAMS

A17

V_SS

NC

A19

A10

DQ7

DQ6

DQ5

DQ4

V_CC

A16

A15

A14

A13

A12

A11

A9

1

2

3

4

40

39

38

37

36

35

34

33

32

31

30

29

28

27

26

25

24

23

22

21

5

6

7

A8

8

WE#

RESET#

NC

RY/BY#

A18

A7

9

10

11

12

13

14

15

16

17

18

19

20

Standard TSOP

NC

DQ3

DQ2

DQ1

DQ0

OE#

V_SS

A6

A5

A4

A3

A2

A1

CE#

A0

PIN CONFIGURATION

LOGIC SYMBOL

A0–A19

= 20 addresses

20

DQ0–DQ7 = 8 data inputs/outputs

A0–A19

8

CE#

=

Chip enable

DQ0–DQ7

OE#

Output enable

WE#

Write enable

CE#

OE#

RESET#

RY/BY#

Hardware reset pin, active low

Ready/Busy# output

WE#

RESET#

V

3.0 volt-only single power supply

CC

(see Product Selector Guide for speed

options and voltage supply tolerances)

RY/BY#

V

=

Device ground

SS

NC

Pin not connected internally

October 11, 2006 21524D6

Am29LV008B

7

D A T A S H E E T

ORDERING INFORMATION

Standard Products

AMD standard products are available in several packages and operating ranges. The order number (Valid Combi-

nation) is formed by a combination of the elements below.

Am29LV008B

T

-70R

E

C

TEMPERATURE RANGE

C

D

I

=

Commercial (0°C to +70°C)

Commercial (0°C to +70°C) with Pb-free package

Industrial (–40°C to +85°C)

Industrial (–40°C to +85°C) with Pb-free package

Extended (–55°C to +125°C)

F

E

K

Extended (–55°C to +125°C) with Pb-free package

PACKAGE TYPE

E

=

40-Pin Thin Small Outline Package (TSOP)

Standard Pinout (TS 040)

SPEED OPTION

See Product Selector Guide and Valid Combinations

BOOT CODE SECTOR ARCHITECTURE

T

B

=

Top Sector

Bottom Sector

DEVICE NUMBER/DESCRIPTION

Am29LV008B

8 Megabit (1 M x 8-Bit) CMOS Flash Memory

3.0 Volt-only Read, Program and Erase

Valid Combinations

Valid Combinations list configurations planned to be sup-

ported in volume for this device. Consult the local AMD sales

office to confirm availability of specific valid combinations and

to check on newly released combinations.

Valid Combinations

AM29LV008BT-70R,

AM29LV008BB-70R

EC, EI, ED, EF

AM29LV008BT-90,

AM29LV008BB-90

EC, EI, EE, ED, EF, EK

AM29LV008BT-120,

AM29LV008BB-120

8

Am29LV008B

21524D6 October 11, 2006

D A T A S H E E T

DEVICE BUS OPERATIONS

This section describes the requirements and use of the

device bus operations, which are initiated through the

internal command register. The command register

itself does not occupy any addressable memory loca-

tion. The register is composed of latches that store the

commands, along with the address and data informa-

tion needed to execute the command. The contents of

the register serve as inputs to the internal state

machine. The state machine outputs dictate the func-

tion of the device. Table 1 lists the device bus

operations, the inputs and control levels they require,

and the resulting output. The following subsections

describe each of these operations in further detail.

Table 1. Am29LV008B Device Bus Operations

Operation

CE#

L

OE#

L

WE#

H

RESET#

Addresses (Note 1)

DQ0–DQ7

D_OUT

Read

Write

H

A_IN

L

H

L

D_IN

V_CC

0.3 V

±

V_CC±

0.3 V

Standby

X

High-Z

Output Disable

Reset

L

H

X

H

X

H

L

X

High-Z

X

Sector Address, A6 = L,

A1 = H, A0 = L

Sector Protect (Note 2)

L

H

L

V_ID

D_IN, D_OUT

Sector Address, A6 = H,

A1 = H, A0 = L

Sector Unprotect (Note 2)

L

H

X

L

V_ID

D_IN, D_OUT

D_IN

Temporary Sector Unprotect

X

A_IN

Legend:

L = Logic Low = V_IL, H = Logic High = V_IH, V_ID= 12.0 ± 0.5 V, X = Don’t Care, A_IN= Address In, D_IN= Data In, D_OUT= Data Out

Notes:

1. Addresses are A19–A0.

2. The sector protect and sector unprotect functions may also be implemented via programming equipment. See the “Sector

Protection/Unprotection” section.

Requirements for Reading Array Data

Writing Commands/Command Sequences

To read array data from the outputs, the system must

To write a command or command sequence (which

includes programming data to the device and erasing

sectors of memory), the system must drive WE# and

drive the CE# and OE# pins to V . CE# is the power

IL

control and selects the device. OE# is the output

control and gates array data to the output pins. WE#

CE# to V , and OE# to V .

IL

IH

should remain at V .

IH

An erase operation can erase one sector, multiple sec-

tors, or the entire device. Tables 2 and 3 indicate the

address space that each sector occupies. A “sector

address” consists of the address bits required to

uniquely select a sector. The “Command Definitions”

section has details on erasing a sector or the entire

chip, or suspending/resuming the erase operation.

The internal state machine is set for reading array data

upon device power-up, or after a hardware reset. This

ensures that no spurious alteration of the memory

content occurs during the power transition. No

command is necessary in this mode to obtain array

data. Standard microprocessor read cycles that assert

valid addresses on the device address inputs produce

valid data on the device data outputs. The device

remains enabled for read access until the command

register contents are altered.

After the system writes the autoselect command

sequence, the device enters the autoselect mode. The

system can then read autoselect codes from the

internal register (which is separate from the memory

array) on DQ7–DQ0. Standard read cycle timings apply

in this mode. Refer to the Autoselect Mode and Autose-

lect Command Sequence sections for more

information.

See “Reading Array Data” for more information. Refer

to the AC Read Operations table for timing specifica-

tions and to Figure 13 for the timing waveforms. I

the DC Characteristics table represents the active

current specification for reading array data.

in

CC1

I

in the DC Characteristics table represents the

CC2

active current specification for the write mode. The “AC

October 11, 2006 21524D6

Am29LV008B

9

D A T A S H E E T

Characteristics” section contains timing specification

tables and timing diagrams for write operations.

Characteristics table represents the automatic sleep

mode current specification.

Program and Erase Operation Status

RESET#: Hardware Reset Pin

During an erase or program operation, the system may

check the status of the operation by reading the status

The RESET# pin provides a hardware method of reset-

ting the device to reading array data. When the

bits on DQ7–DQ0. Standard read cycle timings and I

RESET# pin is driven low for at least a period of t , the

CC

RP

read specifications apply. Refer to “Write Operation

Status” for more information, and to “AC Characteris-

tics” for timing diagrams.

device immediately terminates any operation in

progress, tristates all output pins, and ignores all

read/write commands for the duration of the RESET#

pulse. The device also resets the internal state

machine to reading array data. The operation that was

interrupted should be reinitiated once the device is

ready to accept another command sequence, to

ensure data integrity.

Standby Mode

When the system is not reading or writing to the device,

it can place the device in the standby mode. In this

mode, current consumption is greatly reduced, and the

outputs are placed in the high impedance state, inde-

pendent of the OE# input.

Current is reduced for the duration of the RESET#

pulse. When RESET# is held at V

0.3 V, the device

SS

draws CMOS standby current (I

). If RESET# is held

CC4

The device enters the CMOS standby mode when the

at V but not within V

0.3 V, the standby current will

IL

SS

CE# and RESET# pins are both held at V ± 0.3 V.

CC

be greater.

(Note that this is a more restricted voltage range than

V .) If CE# and RESET# are held at V , but not within

The RESET# pin may be tied to the system reset cir-

cuitry. A system reset would thus also reset the Flash

memory, enabling the system to read the boot-up firm-

ware from the Flash memory.

IH

V

± 0.3 V, the device will be in the standby mode, but

CC

the standby current will be greater. The device requires

standard access time (t ) for read access when the

CE

device is in either of these standby modes, before it is

ready to read data.

If RESET# is asserted during a program or erase oper-

ation, the RY/BY# pin remains a “0” (busy) until the

internal reset operation is complete, which requires a

If the device is deselected during erasure or program-

ming, the device draws active current until the

operation is completed.

time of t

(during Embedded Algorithms). The

READY

system can thus monitor RY/BY# to determine whether

the reset operation is complete. If RESET# is asserted

when a program or erase operation is not executing

(RY/BY# pin is “1”), the reset operation is completed

In the DC Characteristics table, I

and I

repre-

CC4

CC3

sents the standby current specification.

within a time of t

rithms). The system can read data t

RESET# pin returns to V .

(not during Embedded Algo-

READY

Automatic Sleep Mode

The automatic sleep mode minimizes Flash device

energy consumption. The device automatically enables

after the

RH

IH

Refer to the AC Characteristics tables for RESET#

parameters and to Figure 14 for the timing diagram.

this mode when addresses remain stable for t

+ 30

ACC

ns. The automatic sleep mode is independent of the

CE#, WE#, and OE# control signals. Standard address

access timings provide new data when addresses are

changed. While in sleep mode, output data is latched

Output Disable Mode

When the OE# input is at V , output from the device is

disabled. The output pins are placed in the high imped-

ance state.

IH

and always available to the system. I

in the DC

CC5

10

Am29LV008B

21524D6 October 11, 2006

D A T A S H E E T

Table 2. Am29LV008BT Top Boot Sector Address Table

Sector Size

Address Range

(in hexadecimal)

Sector

SA0

A19

0

A18

0

A17

A16

A15

X

0

A14

X

0

A13

X

0

(Kbytes)

64

32

8

0

00000h–0FFFFh

10000h–1FFFFh

20000h–2FFFFh

30000h–3FFFFh

40000h–4FFFFh

50000h–5FFFFh

60000h–6FFFFh

70000h–7FFFFh

80000h–8FFFFh

90000h–9FFFFh

A0000h–AFFFFh

B0000h–BFFFFh

C0000h–CFFFFh

D0000h–DFFFFh

E0000h–EFFFFh

F0000h–F7FFFh

F8000h–F9FFFh

FA000h–FBFFFh

FC000h–FFFFFh

SA1

0

1

SA2

0

1

0

SA3

0

1

SA4

0

1

0

SA5

0

1

0

1

SA6

0

1

0

SA7

0

1

SA8

1

0

SA9

1

0

1

SA10

SA11

SA12

SA13

SA14

SA15

SA16

SA17

SA18

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

8

1

X

16

Table 3. Am29LV008BB Bottom Boot Sector Address Table

Sector Size

Address Range

(in hexadecimal)

Sector

SA0

A19

0

A18

A17

A16

A15

A14

A13

X

0

(Kbytes)

16

8

0

00000h-03FFFh

04000h-05FFFh

06000h-07FFFh

08000h-0FFFFh

10000h-1FFFFh

20000h-2FFFFh

30000h-3FFFFh

40000h-4FFFFh

50000h-5FFFFh

60000h-6FFFFh

70000h-7FFFFh

80000h-8FFFFh

90000h-9FFFFh

A0000h-AFFFFh

B0000h-BFFFFh

C0000h-CFFFFh

D0000h-DFFFFh

E0000h-EFFFFh

F0000h-FFFFFh

SA1

0

1

SA2

0

1

8

SA3

0

1

X

32

64

SA4

0

1

X

SA5

0

1

0

SA6

0

1

SA7

0

1

0

SA8

0

1

0

1

SA9

0

1

0

SA10

SA11

SA12

SA13

SA14

SA15

SA16

SA17

SA18

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

October 11, 2006 21524D6

Am29LV008B

11

D A T A S H E E T

Table 4. In addition, when verifying sector protection,

Autoselect Mode

the sector address must appear on the appropriate

highest order address bits (see Tables 2 and 3). Table

4 shows the remaining address bits that are don’t care.

When all necessary bits have been set as required, the

programming equipment may then read the corre-

sponding identifier code on DQ7–DQ0.

The autoselect mode provides manufacturer and

device identification, and sector protection verification,

through identifier codes output on DQ7–DQ0. This

mode is primarily intended for programming equipment

to automatically match a device to be programmed with

its corresponding programming algorithm. However,

the autoselect codes can also be accessed in-system

through the command register.

To access the autoselect codes in-system, the host

system can issue the autoselect command via the

command register, as shown in Table 5. This method

When using programming equipment, the autoselect

mode requires V (11.5 V to 12.5 V) on address pin

does not require V . See “Command Definitions” for

ID

details on using the autoselect mode.

A9. Address pins A6, A1, and A0 must be as shown in

Table 4. Am29LV008B Autoselect Codes (High Voltage Method)

A19 A12

to to

CE# OE# WE# A13 A10 A9

A8

to

A7

A5

to

A2

DQ7

to

DQ0

Description

A6

A1

A0

Manufacturer ID: AMD

L

H

X

V_ID

X

L

X

L

01h

3Eh

Device ID: Am29LV008BT

(Top Boot Block)

L

H

Device ID: Am29LV008BB

(Bottom Boot Block)

L

H

X

V_ID

X

37h

01h

(protected)

Sector Protection Verification

SA

V_ID

L

H

L

00h

(unprotected)

L = Logic Low = V_IL, H = Logic High = V_IH, SA = Sector Address, X = Don’t care.

The primary method requires V on the RESET# pin

Sector Protection/Unprotection

ID

only, and can be implemented either in-system or via

programming equipment. Figure 2 shows the algo-

rithms and Figure 21 shows the waveform. This

method uses standard microprocessor bus cycle

timing. For sector unprotect, all unprotected sectors

must first be protected prior to the first sector unprotect

write cycle.

The hardware sector protection feature disables both

program and erase operations in any sector. The hard-

ware sector unprotection feature re-enables both

program and erase operations in previously protected

sectors.

The device is shipped with all sectors unprotected.

AMD offers the option of programming and protecting

sectors at its factory prior to shipping the device

through AMD’s ExpressFlash™ Service. Contact an

AMD representative for details.

The alternate method intended only for programming

equipment requires V on address pin A9 and OE#.

ID

This method is compatible with programmer routines

written for earlier 3.0 volt-only AMD flash devices.

Details on this method are provided in a supplement,

publication number 20875. Contact an AMD represen-

tative to request a copy.

It is possible to determine whether a sector is protected

or unprotected. See “Autoselect Mode” for details.

Sector protection/unprotection can be implemented via

two methods.

12

Am29LV008B

21524D6 October 11, 2006

D A T A S H E E T

START

Protect all sectors:

The indicated portion

of the sector protect

algorithm must be

performed for all

PLSCNT = 1

RESET# = V_ID

unprotected sectors

prior to issuing the

first sector

Wait 1 μs

unprotect address

No

First Write

Cycle = 60h?

No

First Write

Cycle = 60h?

Temporary Sector

Unprotect Mode

Temporary Sector

Unprotect Mode

Yes

Set up sector

address

No

All sectors

protected?

Sector Protect:

Write 60h to sector

address with

A6 = 0, A1 = 1,

A0 = 0

Yes

Set up first sector

address

Sector Unprotect:

Wait 150 µs

Write 60h to sector

address with

A6 = 1, A1 = 1,

A0 = 0

Verify Sector

Protect: Write 40h

to sector address

with A6 = 0,

Reset

PLSCNT = 1

Increment

PLSCNT

Wait 15 ms

A1 = 1, A0 = 0

Verify Sector

Unprotect: Write

40h to sector

address with

A6 = 1, A1 = 1,

A0 = 0

Read from

sector address

with A6 = 0,

A1 = 1, A0 = 0

Increment

PLSCNT

No

PLSCNT

= 25?

Read from

sector address

with A6 = 1,

Data = 01h?

Yes

A1 = 1, A0 = 0

No

Yes

Set up

next sector

address

Yes

No

PLSCNT

= 1000?

Protect another

sector?

Data = 00h?

Yes

Device failed

No

Yes

Remove V_ID

from RESET#

No

Last sector

verified?

Device failed

Write reset

command

Yes

Remove V_ID

Sector Unprotect

Algorithm

from RESET#

Sector Protect

Algorithm

Sector Protect

complete

Write reset

command

Sector Unprotect

complete

Figure 1. In-System Sector Protect/Sector Unprotect Algorithms

October 11, 2006 21524D6

Am29LV008B

13

D A T A S H E E T

Temporary Sector Unprotect

Hardware Data Protection

This feature allows temporary unprotection of previ-

ously protected sectors to change data in-system. The

Sector Unprotect mode is activated by setting the

The command sequence requirement of unlock cycles

for programming or erasing provides data protection

against inadvertent writes (refer to Table 5 for

command definitions). In addition, the following hard-

ware data protection measures prevent accidental

erasure or programming, which might otherwise be

RESET# pin to V . During this mode, formerly pro-

ID

tected sectors can be programmed or erased by

selecting the sector addresses. Once V is removed

ID

from the RESET# pin, all the previously protected

sectors are protected again. Figure 2 shows the algo-

rithm, and Figure 20 shows the timing diagrams, for this

feature.

caused by spurious system level signals during V

power-up and power-down transitions, or from system

noise.

CC

Low V

Write Inhibit

CC

When V

is less than V

, the device does not

LKO

CC

accept any write cycles. This protects data during V

CC

power-up and power-down. The command register and

all internal program/erase circuits are disabled, and the

START

device resets. Subsequent writes are ignored until V

CC

is greater than V

proper signals to the control pins to prevent uninten-

tional writes when V is greater than V

. The system must provide the

LKO

RESET# = V_ID

(Note 1)

.

CC

LKO

Write Pulse “Glitch” Protection

Perform Erase or

Program Operations

Noise pulses of less than 5 ns (typical) on OE#, CE# or

WE# do not initiate a write cycle.

Logical Inhibit

RESET# = V_IH

Write cycles are inhibited by holding any one of OE# =

V , CE# = V or WE# = V . To initiate a write cycle,

IL

IH

CE# and WE# must be a logical zero while OE# is a

logical one.

Temporary Sector

Unprotect Completed

(Note 2)

Power-Up Write Inhibit

If WE# = CE# = V and OE# = V during power up, the

IL

IH

device does not accept commands on the rising edge

of WE#. The internal state machine is automatically

reset to reading array data on power-up.

Note:

1. All protected sectors unprotected.

2. All previously protected sectors are protected once

again.

Figure 2. Temporary Sector Unprotect Operation

14

Am29LV008B

21524D6 October 11, 2006

D A T A S H E E T

COMMAND DEFINITIONS

Writing specific address and data commands or

sequences into the command register initiates device

operations. Table 5 defines the valid register command

sequences. Writing incorrect address and data

values or writing them in the improper sequence

resets the device to reading array data.

however, the device ignores reset commands until the

operation is complete.

The reset command may be written between the

sequence cycles in an autoselect command sequence.

Once in the autoselect mode, the reset command must

be written to return to reading array data (also applies

to autoselect during Erase Suspend).

All addresses are latched on the falling edge of WE# or

CE#, whichever happens later. All data is latched on

the rising edge of WE# or CE#, whichever happens

first. Refer to the appropriate timing diagrams in the

“AC Characteristics” section.

If DQ5 goes high during a program or erase operation,

writing the reset command returns the device to

reading array data (also applies during Erase

Suspend).

Reading Array Data

Autoselect Command Sequence

The device is automatically set to reading array data

after device power-up. No commands are required to

retrieve data. The device is also ready to read array

data after completing an Embedded Program or

Embedded Erase algorithm.

The autoselect command sequence allows the host

system to access the manufacturer and devices codes,

and determine whether or not a sector is protected.

Table 5 shows the address and data requirements. This

method is an alternative to that shown in Table 4, which

After the device accepts an Erase Suspend command,

the device enters the Erase Suspend mode. The

system can read array data using the standard read

timings, except that if it reads at an address within

erase-suspended sectors, the device outputs status

data. After completing a programming operation in the

Erase Suspend mode, the system may once again

read array data with the same exception. See “Erase

Suspend/Erase Resume Commands” for more infor-

mation on this mode.

is intended for PROM programmers and requires V

on address bit A9.

ID

The autoselect command sequence is initiated by

writing two unlock cycles, followed by the autoselect

command. The device then enters the autoselect

mode, and the system may read at any address any

number of times, without initiating another command

sequence.

A read cycle at address XX00h retrieves the manufac-

turer code. A read cycle at address XX01h returns the

device code. A read cycle containing a sector address

(SA) and the address 02h returns 01h if that sector is

protected, or 00h if it is unprotected. Refer to Tables 2

and 3 for valid sector addresses.

The system must issue the reset command to re-

enable the device for reading array data if DQ5 goes

high, or while in the autoselect mode. See the “Reset

Command” section, next.

See also “Requirements for Reading Array Data” in the

“Device Bus Operations” section for more information.

The Read Operations table provides the read parame-

ters, and Figure 13 shows the timing diagram.

The system must write the reset command to exit the

autoselect mode and return to reading array data.

Byte Program Command Sequence

Programming is a four-bus-cycle operation. The

program command sequence is initiated by writing two

unlock write cycles, followed by the program set-up

command. The program address and data are written

next, which in turn initiate the Embedded Program

algorithm. The system is not required to provide further

controls or timings. The device automatically provides

internally generated program pulses and verifies the

programmed cell margin. Table 5 shows the address

and data requirements for the byte program command

sequence.

Reset Command

Writing the reset command to the device resets the

device to reading array data. Address bits are don’t

care for this command.

The reset command may be written between the

sequence cycles in an erase command sequence

before erasing begins. This resets the device to reading

array data. Once erasure begins, however, the device

ignores reset commands until the operation is

complete.

The reset command may be written between the

sequence cycles in a program command sequence

before programming begins. This resets the device to

reading array data (also applies to programming in

Erase Suspend mode). Once programming begins,

When the Embedded Program algorithm is complete,

the device then returns to reading array data and

addresses are no longer latched. The system can

determine the status of the program operation by using

DQ7, DQ6, or RY/BY#. See “Write Operation Status”

for information on these status bits.

October 11, 2006 21524D6

Am29LV008B

15

D A T A S H E E T

Any commands written to the device during the

Embedded Program Algorithm are ignored. Note that a

hardware reset immediately terminates the program-

ming operation. The Byte Program command

sequence should be reinitiated once the device has

reset to reading array data, to ensure data integrity.

START

Write Program

Command Sequence

Programming is allowed in any sequence and across

sector boundaries. A bit cannot be programmed

from a “0” back to a “1”. Attempting to do so may halt

the operation and set DQ5 to “1”, or cause the Data#

Polling algorithm to indicate the operation was suc-

cessful. However, a succeeding read will show that the

data is still “0”. Only erase operations can convert a “0”

to a “1”.

Data Poll

from System

Embedded

Program

algorithm

in progress

Unlock Bypass Command Sequence

Verify Data?

Yes

The unlock bypass feature allows the system to

program bytes or words to the device faster than using

the standard program command sequence. The unlock

bypass command sequence is initiated by first writing

two unlock cycles. This is followed by a third write cycle

containing the unlock bypass command, 20h. The

device then enters the unlock bypass mode. A two-

cycle unlock bypass program command sequence is all

that is required to program in this mode. The first cycle

in this sequence contains the unlock bypass program

command, A0h; the second cycle contains the program

address and data. Additional data is programmed in

the same manner. This mode dispenses with the initial

two unlock cycles required in the standard program

command sequence, resulting in faster total program-

ming time. The Command Definitions table shows the

requirements for the command sequence.

No

Increment Address

Last Address?

Yes

Programming

Completed

Note: See Table 5 for program command sequence.

Figure 3. Program Operation

During the unlock bypass mode, only the Unlock

Bypass Program and Unlock Bypass Reset commands

are valid. To exit the unlock bypass mode, the system

must issue the two-cycle unlock bypass reset

command sequence. The first cycle must contain the

data 90h; the second cycle the data 00h. Addresses

are don’t care for both cycles. The device then returns

to reading array data.

Chip Erase Command Sequence

Chip erase is a six bus cycle operation. The chip erase

command sequence is initiated by writing two unlock

cycles, followed by a set-up command. Two additional

unlock write cycles are then followed by the chip erase

command, which in turn invokes the Embedded Erase

algorithm. The device does not require the system to

preprogram prior to erase. The Embedded Erase algo-

rithm automatically preprograms and verifies the entire

memory for an all zero data pattern prior to electrical

erase. The system is not required to provide any con-

trols or timings during these operations. Table 5 shows

the address and data requirements for the chip erase

command sequence.

Figure 3 illustrates the algorithm for the program oper-

ation. See the Erase/Program Operations table in “AC

Characteristics” for parameters, and Figure 15 for

timing diagrams.

Any commands written to the chip during the

Embedded Erase algorithm are ignored. Note that a

hardware reset during the chip erase operation imme-

diately terminates the operation. The Chip Erase

command sequence should be reinitiated once the

16

Am29LV008B

21524D6 October 11, 2006

D A T A S H E E T

device has returned to reading array data, to ensure

operation. The Sector Erase command sequence

should be reinitiated once the device has returned to

reading array data, to ensure data integrity.

data integrity.

The system can determine the status of the erase oper-

ation by using DQ7, DQ6, DQ2, or RY/BY#. See “Write

Operation Status” for information on these status bits.

When the Embedded Erase algorithm is complete, the

device returns to reading array data and addresses are

no longer latched.

When the Embedded Erase algorithm is complete, the

device returns to reading array data and addresses are

no longer latched. The system can determine the

status of the erase operation by using DQ7, DQ6, DQ2,

or RY/BY#. Refer to “Write Operation Status” for infor-

mation on these status bits.

Figure 4 illustrates the algorithm for the erase opera-

tion. See the Erase/Program Operations tables in “AC

Characteristics” for parameters, and to Figure 16 for

timing diagrams.

Figure 4 illustrates the algorithm for the erase opera-

tion. Refer to the Erase/Program Operations tables in

the “AC Characteristics” section for parameters, and to

Figure 16 for timing waveforms.

Sector Erase Command Sequence

Erase Suspend/Erase Resume Commands

Sector erase is a six bus cycle operation. The sector

erase command sequence is initiated by writing two

unlock cycles, followed by a set-up command. Two

additional unlock write cycles are then followed by the

address of the sector to be erased, and the sector

erase command. Table 5 shows the address and data

requirements for the sector erase command sequence.

The Erase Suspend command allows the system to

interrupt a sector erase operation and then read data

from, or program data to, any sector not selected for

erasure. This command is valid only during the sector

erase operation, including the 50 µs time-out period

during the sector erase command sequence. The

Erase Suspend command is ignored if written during

the chip erase operation or Embedded Program algo-

rithm. Writing the Erase Suspend command during the

Sector Erase time-out immediately terminates the

time-out period and suspends the erase operation.

Addresses are “don’t-cares” when writing the Erase

Suspend command.

The device does not require the system to preprogram

the memory prior to erase. The Embedded Erase algo-

rithm automatically programs and verifies the sector for

an all zero data pattern prior to electrical erase. The

system is not required to provide any controls or

timings during these operations.

After the command sequence is written, a sector erase

time-out of 50 µs begins. During the time-out period,

additional sector addresses and sector erase com-

mands may be written. Loading the sector erase buffer

may be done in any sequence, and the number of

sectors may be from one sector to all sectors. The time

between these additional cycles must be less than 50

µs, otherwise the last address and command might not

be accepted, and erasure may begin. It is recom-

mended that processor interrupts be disabled during

this time to ensure all commands are accepted. The

interrupts can be re-enabled after the last Sector Erase

command is written. If the time between additional

sector erase commands can be assumed to be less

than 50 µs, the system need not monitor DQ3. Any

command other than Sector Erase or Erase

Suspend during the time-out period resets the

device to reading array data. The system must

rewrite the command sequence and any additional

sector addresses and commands.

When the Erase Suspend command is written during a

sector erase operation, the device requires a maximum

of 20 µs to suspend the erase operation. However,

when the Erase Suspend command is written during

the sector erase time-out, the device immediately ter-

minates the time-out period and suspends the erase

operation.

After the erase operation has been suspended, the

system can read array data from or program data to

any sector not selected for erasure. (The device “erase

suspends” all sectors selected for erasure.) Normal

read and write timings and command definitions apply.

Reading at any address within erase-suspended

sectors produces status data on DQ7–DQ0. The

system can use DQ7, or DQ6 and DQ2 together, to

determine if a sector is actively erasing or is erase-sus-

pended. See “Write Operation Status” for information

on these status bits.

After an erase-suspended program operation is com-

plete, the system can once again read array data within

non-suspended sectors. The system can determine

the status of the program operation using the DQ7 or

DQ6 status bits, just as in the standard program oper-

ation. See “Write Operation Status” for more

information.

The system can monitor DQ3 to determine if the sector

erase timer has timed out. (See the “DQ3: Sector Erase

Timer” section.) The time-out begins from the rising

edge of the final WE# pulse in the command sequence.

Once the sector erase operation has begun, only the

Erase Suspend command is valid. All other commands

are ignored. Note that a hardware reset during the

sector erase operation immediately terminates the

The system may also write the autoselect command

sequence when the device is in the Erase Suspend

October 11, 2006 21524D6

Am29LV008B

17

D A T A S H E E T

mode. The device allows reading autoselect codes

even at addresses within erasing sectors, since the

codes are not stored in the memory array. When the

device exits the autoselect mode, the device reverts to

the Erase Suspend mode, and is ready for another

valid operation. See “Autoselect Command Sequence”

for more information.

START

Write Erase

Command Sequence

The system must write the Erase Resume command

(address bits are “don’t care”) to exit the erase suspend

mode and continue the sector erase operation. Further

writes of the Resume command are ignored. Another

Erase Suspend command can be written after the

device has resumed erasing.

Data Poll

from System

Embedded

Erase

algorithm

in progress

No

Data = FFh?

Yes

Erasure Completed

Notes:

1. See Table 5 for erase command sequence.

2. See “DQ3: Sector Erase Timer” for more information.

Figure 4. Erase Operation

18

Am29LV008B

21524D6 October 11, 2006

D A T A S H E E T

Command Definitions

Table 5. Am29LV008B Command Definitions

Bus Cycles (Notes 2-4)

Command

Sequence

(Note 1)

First

Second

Third

Fourth

Fifth

Sixth

Addr Data Addr Data Addr Data Addr Data Addr Data Addr Data

Read (Note 5)

Reset (Note 6)

Manufacturer ID

1

4

RA

XXX

555

RD

F0

AA

2AA

55

555

90

X00

X01

01

3E

37

00

01

PD

Device ID, Top Boot Block

Auto-

select

Device ID, Bottom Boot Block

(Note 7)

Sector Protect Verify

(Note 8)

(SA)

X02

4

555

AA

2AA

55

555

90

Program

4

3

2

6

1

555

AA

A0

90

2AA

PA

55

PD

00

55

555

A0

20

PA

Unlock Bypass

Unlock Bypass Program (Note 9)

Unlock Bypass Reset (Note 10)

Chip Erase

XXX

555

XXX

2AA

AA

B0

30

555

80

555

AA

2AA

55

555

SA

10

30

Sector Erase

555

Erase Suspend (Note 11)

Erase Resume (Note 12)

XXX

Legend:

X = Don’t care

PD = Data to be programmed at location PA. Data latches on the

rising edge of WE# or CE# pulse, whichever happens first.

RA = Address of the memory location to be read.

SA = Address of the sector to be verified (in autoselect mode) or

erased. Address bits A19–A13 uniquely select any sector.

RD = Data read from location RA during read operation.

PA = Address of the memory location to be programmed.

Addresses latch on the falling edge of the WE# or CE# pulse,

whichever happens later.

Notes:

1. See Table 1 for description of bus operations.

8. The data is 00h for an unprotected sector and 01h for a

protected sector. See “Autoselect Command Sequence” for

more information.

2. All values are in hexadecimal.

3. Except when reading array or autoselect data, all bus cycles

are write operations.

9. The Unlock Bypass command is required prior to the Unlock

Bypass Program command.

4. Address bits A19–A11 are don’t cares for unlock and

command cycles.

10. The Unlock Bypass Reset command is required to return to

reading array data when the device is in the unlock bypass

mode.

5. No unlock or command cycles required when reading array

data.

11. The system may read and program in non-erasing sectors, or

enter the autoselect mode, when in the Erase Suspend

mode. The Erase Suspend command is valid only during a

sector erase operation.

6. The Reset command is required to return to reading array

data when device is in the autoselect mode, or if DQ5 goes

high (while the device is providing status data).

7. The fourth cycle of the autoselect command sequence is a

read cycle.

12. The Erase Resume command is valid only during the Erase

Suspend mode.

October 11, 2006 21524D6

Am29LV008B

19

D A T A S H E E T

WRITE OPERATION STATUS

The device provides several bits to determine the

status of a write operation: DQ2, DQ3, DQ5, DQ6,

DQ7, and RY/BY#. Table 6 and the following subsec-

tions describe the functions of these bits. DQ7,

RY/BY#, and DQ6 each offer a method for determining

whether a program or erase operation is complete or in

progress. These three bits are discussed first.

Table 6 shows the outputs for Data# Polling on DQ7.

Figure 5 shows the Data# Polling algorithm.

START

DQ7: Data# Polling

Read DQ7–DQ0

Addr = VA

The Data# Polling bit, DQ7, indicates to the host

system whether an Embedded Algorithm is in progress

or completed, or whether the device is in Erase Sus-

pend. Data# Polling is valid after the rising edge of the

final WE# pulse in the program or erase command

sequence.

Yes

DQ7 = Data?

During the Embedded Program algorithm, the device

outputs on DQ7 the complement of the datum pro-

grammed to DQ7. This DQ7 status also applies to

programming during Erase Suspend. When the

Embedded Program algorithm is complete, the device

outputs the datum programmed to DQ7. The system

must provide the program address to read valid status

information on DQ7. If a program address falls within a

protected sector, Data# Polling on DQ7 is active for

approximately 1 µs, then the device returns to reading

array data.

No

DQ5 = 1?

Yes

Read DQ7–DQ0

Addr = VA

During the Embedded Erase algorithm, Data# Polling

produces a “0” on DQ7. When the Embedded Erase

algorithm is complete, or if the device enters the Erase

Suspend mode, Data# Polling produces a “1” on DQ7.

This is analogous to the complement/true datum output

described for the Embedded Program algorithm: the

erase function changes all the bits in a sector to “1”;

prior to this, the device outputs the “complement,” or

“0.” The system must provide an address within any of

the sectors selected for erasure to read valid status

information on DQ7.

Yes

DQ7 = Data?

No

PASS

FAIL

After an erase command sequence is written, if all

sectors selected for erasing are protected, Data#

Polling on DQ7 is active for approximately 100 µs, then

the device returns to reading array data. If not all

selected sectors are protected, the Embedded Erase

algorithm erases the unprotected sectors, and ignores

the selected sectors that are protected.

Notes:

1. VA = Valid address for programming. During a sector

erase operation, a valid address is an address within any

sector selected for erasure. During chip erase, a valid

address is any non-protected sector address.

2. DQ7 should be rechecked even if DQ5 = “1” because

DQ7 may change simultaneously with DQ5.

When the system detects DQ7 has changed from the

complement to true data, it can read valid data at DQ7–

DQ0 on the following read cycles. This is because DQ7

may change asynchronously with DQ0–DQ6 while

Output Enable (OE#) is asserted low. Figure 17, Data#

Polling Timings (During Embedded Algorithms), in the

“AC Characteristics” section illustrates this.

Figure 5. Data# Polling Algorithm

20

Am29LV008B

21524D6 October 11, 2006

D A T A S H E E T

Table 6 shows the outputs for Toggle Bit I on DQ6.

RY/BY#: Ready/Busy#

Refer to Figure 6 shows the toggle bit algorithm and to

Figure 18 in the “AC Characteristics” section for the

timing diagrams. Figure 19 shows the differences

between DQ2 and DQ6 in graphical form. See also the

subsection on “DQ2: Toggle Bit II”.

The RY/BY# is a dedicated, open-drain output pin that

indicates whether an Embedded Algorithm is in

progress or complete. The RY/BY# status is valid after

the rising edge of the final WE# pulse in the command

sequence. Since RY/BY# is an open-drain output,

several RY/BY# pins can be tied together in parallel

DQ2: Toggle Bit II

with a pull-up resistor to V

.

CC

The “Toggle Bit II” on DQ2, when used with DQ6, indi-

cates whether a particular sector is actively erasing

(that is, the Embedded Erase algorithm is in progress),

or whether that sector is erase-suspended. Toggle Bit

II is valid after the rising edge of the final WE# pulse in

the command sequence.

If the output is low (Busy), the device is actively erasing

or programming. (This includes programming in the

Erase Suspend mode.) If the output is high (Ready),

the device is ready to read array data (including during

the Erase Suspend mode), or is in the standby mode.

Table 6 shows the outputs for RY/BY#. Figures 13, 14,

15 and 16 shows RY/BY# for read, reset, program, and

erase operations, respectively.

DQ2 toggles when the system reads at addresses

within those sectors that have been selected for era-

sure. (The system may use either OE# or CE# to

control the read cycles.) But DQ2 cannot distinguish

whether the sector is actively erasing or is erase-sus-

pended. DQ6, by comparison, indicates whether the

device is actively erasing, or is in Erase Suspend, but

cannot distinguish which sectors are selected for era-

sure. Thus, both status bits are required for sector and

mode information. Refer to Table 6 to compare outputs

for DQ2 and DQ6.

DQ6: Toggle Bit I

Toggle Bit I on DQ6 indicates whether an Embedded

Program or Erase algorithm is in progress or complete,

or whether the device has entered the Erase Suspend

mode. Toggle Bit I may be read at any address, and is

valid after the rising edge of the final WE# pulse in the

command sequence (prior to the program or erase

operation), and during the sector erase time-out.

Figure 6 shows the toggle bit algorithm in flowchart

form, and the section “DQ2: Toggle Bit II” explains the

algorithm. See also the DQ6: Toggle Bit I subsection.

Refer to Figure 18 for the toggle bit timing diagram.

Figure 19 shows the differences between DQ2 and

DQ6 in graphical form.

During an Embedded Program or Erase algorithm

operation, successive read cycles to any address

cause DQ6 to toggle. (The system may use either OE#

or CE# to control the read cycles.) When the operation

is complete, DQ6 stops toggling.

After an erase command sequence is written, if all

sectors selected for erasing are protected, DQ6 toggles

for approximately 100 µs, then returns to reading array

data. If not all selected sectors are protected, the

Embedded Erase algorithm erases the unprotected

sectors, and ignores the selected sectors that are

protected.

Reading Toggle Bits DQ6/DQ2

Refer to Figure 6 for the following discussion. When-

ever the system initially begins reading toggle bit

status, it must read DQ7–DQ0 at least twice in a row to

determine whether a toggle bit is toggling. Typically, the

system would note and store the value of the toggle bit

after the first read. After the second read, the system

would compare the new value of the toggle bit with the

first. If the toggle bit is not toggling, the device has com-

pleted the program or erase operation. The system can

read array data on DQ7–DQ0 on the following read

cycle.

The system can use DQ6 and DQ2 together to deter-

mine whether a sector is actively erasing or is erase-

suspended. When the device is actively erasing (that is,

the Embedded Erase algorithm is in progress), DQ6

toggles. When the device enters the Erase Suspend

mode, DQ6 stops toggling. However, the system must

also use DQ2 to determine which sectors are erasing

or erase-suspended. Alternatively, the system can use

DQ7 (see the subsection on DQ7: Data# Polling).

However, if after the initial two read cycles, the system

determines that the toggle bit is still toggling, the

system also should note whether the value of DQ5 is

high (see the section on DQ5). If it is, the system

should then determine again whether the toggle bit is

toggling, since the toggle bit may have stopped tog-

gling just as DQ5 went high. If the toggle bit is no longer

toggling, the device has successfully completed the

program or erase operation. If it is still toggling, the

device did not completed the operation successfully,

and the system must write the reset command to return

to reading array data.

If a program address falls within a protected sector,

DQ6 toggles for approximately 1 µs after the program

command sequence is written, then returns to reading

array data.

DQ6 also toggles during the erase-suspend-program

mode, and stops toggling once the Embedded

Program algorithm is complete.

October 11, 2006 21524D6

Am29LV008B

21

D A T A S H E E T

The remaining scenario is that the system initially

DQ5: Exceeded Timing Limits

determines that the toggle bit is toggling and DQ5 has

not gone high. The system may continue to monitor the

toggle bit and DQ5 through successive read cycles,

determining the status as described in the previous

paragraph. Alternatively, it may choose to perform

other system tasks. In this case, the system must start

at the beginning of the algorithm when it returns to

determine the status of the operation (top of Figure 6).

DQ5 indicates whether the program or erase time has

exceeded a specified internal pulse count limit. Under

these conditions DQ5 produces a “1.” This is a failure

condition that indicates the program or erase cycle was

not successfully completed.

The DQ5 failure condition may appear if the system

tries to program a “1” to a location that is previously pro-

grammed to “0.” Only an erase operation can change

a “0” back to a “1.” Under this condition, the device

halts the operation, and when the operation has

exceeded the timing limits, DQ5 produces a “1.”

START

Under both these conditions, the system must issue the

reset command to return the device to reading array

data.

Read DQ7–DQ0

(Note 1)

DQ3: Sector Erase Timer

After writing a sector erase command sequence, the

system may read DQ3 to determine whether or not an

erase operation has begun. (The sector erase timer

does not apply to the chip erase command.) If addi-

tional sectors are selected for erasure, the entire time-

out also applies after each additional sector erase com-

mand. When the time-out is complete, DQ3 switches

from “0” to “1.” The system may ignore DQ3 if the

system can guarantee that the time between addi-

tional sector erase commands will always be less than

50 μs. See also the “Sector Erase Command

Sequence” section.

Read DQ7–DQ0

No

Toggle Bit

= Toggle?

Yes

No

DQ5 = 1?

Yes

After the sector erase command sequence is written,

the system should read the status on DQ7 (Data#

Polling) or DQ6 (Toggle Bit I) to ensure the device has

accepted the command sequence, and then read DQ3.

If DQ3 is “1”, the internally controlled erase cycle has

begun; all further commands (other than Erase Sus-

pend) are ignored until the erase operation is complete.

If DQ3 is “0”, the device will accept additional sector

erase commands. To ensure the command has been

accepted, the system software should check the status

of DQ3 prior to and following each subsequent sector

erase command. If DQ3 is high on the second status

check, the last command might not have been

accepted. Table 6 shows the outputs for DQ3.

(Notes

1, 2)

Read DQ7–DQ0

Twice

Toggle Bit

= Toggle?

No

Yes

Program/Erase

Operation Not

Complete, Write

Reset Command

Program/Erase

Operation Complete

Notes:

1. Read toggle bit twice to determine whether or not it is

toggling. See text.

2. Recheck toggle bit because it may stop toggling as DQ5

changes to “1” . See text.

Figure 6. Toggle Bit Algorithm

22

Am29LV008B

21524D6 October 11, 2006

D A T A S H E E T

Table 6. Write Operation Status

DQ7

DQ5

DQ2

Operation

(Note 2)

DQ6

(Note 1)

DQ3

N/A

1

(Note 2)

RY/BY#

Embedded Program Algorithm

Embedded Erase Algorithm

DQ7#

0

Toggle

0

No toggle

Toggle

0

Standard

Mode

Reading within Erase

Suspended Sector

1

No toggle

0

N/A

Toggle

1

Erase

Suspend Reading within Non-Erase

Data

0

Data

N/A

Data

N/A

1

0

Mode

Suspended Sector

Erase-Suspend-Program

DQ7#

Toggle

Notes:

1. DQ5 switches to ‘1’ when an Embedded Program or Embedded Erase operation has exceeded the maximum timing limits.

See “DQ5: Exceeded Timing Limits” for more information.

2. DQ7 and DQ2 require a valid address when reading status information. Refer to the appropriate subsection for further details.

October 11, 2006 21524D6

Am29LV008B

23

D A T A S H E E T

ABSOLUTE MAXIMUM RATINGS

Storage Temperature

Plastic Packages . . . . . . . . . . . . . . . –65°C to +150°C

20 ns

Ambient Temperature

with Power Applied. . . . . . . . . . . . . . –65°C to +125°C

+0.8 V

Voltage with Respect to Ground

–0.5 V

–2.0 V

V

(Note 1) . . . . . . . . . . . . . . . .–0.5 V to +4.0 V

CC

A9, OE#, and

RESET# (Note 2). . . . . . . . . . . .–0.5 V to +12.5 V

20 ns

All other pins (Note 1) . . . . . –0.5 V to V +0.5 V

CC

Figure 7. Maximum Negative

Overshoot Waveform

Output Short Circuit Current (Note 3) . . . . . . 200 mA

Notes:

1. Minimum DC voltage on input or I/O pins is –0.5 V. During

voltage transitions, input or I/O pins may undershoot V_SS

to –2.0 V for periods of up to 20 ns. See Figure 7.

Maximum DC voltage on input or I/O pins is V_CC+0.5 V.

During voltage transitions, input or I/O pins may overshoot

to V_CC+2.0 V for periods up to 20 ns. See Figure 8.

20 ns

V_CC

2. Minimum DC input voltage on pins A9, OE#, and RESET#

is –0.5 V. During voltage transitions, A9, OE#, and

RESET# may undershoot V_SSto –2.0 V for periods of up

to 20 ns. See Figure 7. Maximum DC input voltage on pin

A9 is +12.5 V which may overshoot to 14.0 V for periods

up to 20 ns.

+2.0 V

V_CC

+0.5 V

2.0 V

20 ns

3. No more than one output may be shorted to ground at a

time. Duration of the short circuit should not be greater

than one second.

Figure 8. Maximum Positive

Overshoot Waveform

Stresses above those listed under “Absolute Maximum

Ratings” may cause permanent damage to the device. This is

a stress rating only; functional operation of the device at

these or any other conditions above those indicated in the

operational sections of this data sheet is not implied.

Exposure of the device to absolute maximum rating

conditions for extended periods may affect device reliability.

OPERATING RANGES

Commercial (C) Devices

Ambient Temperature (T ) . . . . . . . . . . . 0°C to +70°C

A

Industrial (I) Devices

Ambient Temperature (T ) . . . . . . . . . –40°C to +85°C

A

Extended (E) Devices

Ambient Temperature (T ) . . . . . . . . –55°C to +125°C

A

V

Supply Voltages

CC

for regulated voltage range. . . . .+3.0 V to +3.6 V

for full voltage range . . . . . . . . . .+2.7 V to +3.6 V

Operating ranges define those limits between which the func-

tionality of the device is guaranteed.

24

Am29LV008B

21524D6 October 11, 2006

D A T A S H E E T

Test Conditions

DC CHARACTERISTICS

CMOS Compatible

Parameter

Description

Min

Typ

Max

±1.0

35

Unit

µA

V_IN= V_SSto V_CC

,

I_LI

Input Load Current

V_CC= V_{CC max}

I_LIT

I_LO

A9 Input Load Current

Output Leakage Current

V_CC= V_{CC max}; A9 = 12.5 V

µA

V_OUT= V_SSto V_CC

,

±1.0

µA

V_CC= V_{CC max}

5 MHz

1 MHz

7

2

12

4

V_CCActive Read Current

(Notes 1, 2)

I_CC1

CE# = V_IL, OE# = V_IH

mA

V_CCActive Write Current

(Notes 2, 3, 5)

I_CC2

I_CC3

I_CC4

CE# = V_IL, OE# = V_IH

15

0.2

30

5

mA

µA

V_CCStandby Current (Note 2)

CE#, RESET# = V_CC± 0.3 V

RESET# = V_SS± 0.3 V

V_CCStandby Current During Reset

(Note 2)

5

V_IH= V_CC± 0.3 V;

V_IL= V_SS± 0.3 V

I_CC5

Automatic Sleep Mode (Notes 2, 4)

0.2

5

µA

V_IL

V_IH

Input Low Voltage

Input High Voltage

–0.5

0.8

V

0.7 x V_CC

V_CC+ 0.3

Voltage for Autoselect and

Temporary Sector Unprotect

V_ID

V_CC= 3.3 V

11.5

12.5

0.45

V

V_OL

Output Low Voltage

I_OL= 4.0 mA, V_CC= V_{CC min}

I_OH= –2.0 mA, V_CC= V_{CC min}

I_OH= –100 µA, V_CC= V_{CC min}

V

V_OH1

V_OH2

V_LKO

0.85 V_CC

V_CC–0.4

2.3

Output High Voltage

Low V_CCLock-Out Voltage (Note 4)

2.5

V

Notes:

1. The I_CCcurrent listed is typically less than 2 mA/MHz, with OE# at V_IH. Typical V_CCis 3.0 V.

2. Maximum I_CCspecifications are tested with V_CC= V_CCmax

.

3. I_CCactive while Embedded Erase or Embedded Program is in progress.

4. Automatic sleep mode enables the low power mode when addresses remain stable for t_ACC+ 30 ns.

5. Not 100% tested.

October 11, 2006 21524D6

Am29LV008B

25

D A T A S H E E T

DC CHARACTERISTICS (continued)

Zero Power Flash

20

15

10

5

0

500

1000

1500

2000

2500

3000

3500

4000

Time in ns

Note: Addresses are switching at 1 MHz

Figure 9.

I

Current vs. Time (Showing Active and Automatic Sleep Currents)

CC1

10

8

3.6 V

2.7 V

6

4

2

0

1

2

3

4

5

Frequency in MHz

Note: T = 25 °C

Figure 10. Typical I

vs. Frequency

CC1

26

Am29LV008B

21524D6 October 11, 2006

D A T A S H E E T

TEST CONDITIONS

Table 7. Test Specifications

-90,

3.3 V

Test Condition

-70R

-120

Unit

2.7 kΩ

Output Load

1 TTL gate

Device

Under

Test

Output Load Capacitance, C_L

(including jig capacitance)

30

100

pF

C

L

6.2 kΩ

Input Rise and Fall Times

Input Pulse Levels

5

0.0–3.0

ns

V

Input timing measurement

reference levels

1.5

V

Note: Diodes are IN3064 or equivalent

Output timing measurement

reference levels

Figure 11. Test Setup

Key to Switching Waveforms

WAVEFORM

INPUTS

OUTPUTS

Steady

Changing from H to L

Changing from L to H

Don’t Care, Any Change Permitted

Does Not Apply

Changing, State Unknown

Center Line is High Impedance State (High Z)

3.0 V

0.0 V

1.5 V

Input

Measurement Level

Output

Figure 12. Input Waveforms and Measurement Levels

October 11, 2006 21524D6

Am29LV008B

27

D A T A S H E E T

AC CHARACTERISTICS

Read Operations

Parameter

Speed Options

JEDEC

Std

Description

Read Cycle Time (Note 1)

Test Setup

-70R

-90

-120 Unit

t_AVAV

t_RC

Min

70

90

120

ns

CE# = V_IL

OE# = V_IL

t_AVQV

t_ACCAddress to Output Delay

Max

90

t_ELQV

t_GLQV

t_EHQZ

t_GHQZ

t_CE

t_OE

t_DF

Chip Enable to Output Delay

Output Enable to Output Delay

OE# = V_IL

Max

Min

70

30

25

90

35

30

0

120

50

ns

Chip Enable to Output High Z (Note 1)

Output Enable to Output High Z (Note 1)

30

Read

Output Enable

Hold Time (Note 1)

t_OEH

Toggle and

Data# Polling

Min

10

0

ns

Output Hold Time From Addresses, CE# or OE#,

Whichever Occurs First (Note 1)

t_AXQX

t_OH

Notes:

1. Not 100% tested.

2. See Figure 11 and Table 7 for test specifications.

t_RC

Addresses Stable

t_ACC

Addresses

CE#

t_DF

t_OE

OE#

t_OEH

WE#

t_CE

t_OH

HIGH Z

Output Valid

Outputs

RESET#

RY/BY#

0 V

Figure 13. Read Operations Timings

28

Am29LV008B

21524D6 October 11, 2006

D A T A S H E E T

AC CHARACTERISTICS

Hardware Reset (RESET#)

Parameter

JEDEC

Std

Description

Test Setup

Max

All Speed Options

Unit

RESET# Pin Low (During Embedded

Algorithms) to Read or Write (See Note)

t_READY

20

µs

RESET# Pin Low (NOT During Embedded

Algorithms) to Read or Write (See Note)

t_READY

Max

500

ns

t_RP

t_RH

RESET# Pulse Width

Min

500

50

20

0

ns

µs

ns

RESET# High Time Before Read (See Note)

t_RPDRESET# Low to Standby Mode

t_RBRY/BY# Recovery Time

Note: Not 100% tested.

RY/BY#

CE#, OE#

RESET#

t_RH

t_RP

t_Ready

Reset Timings NOT during Embedded Algorithms

Reset Timings during Embedded Algorithms

t_Ready

RY/BY#

t_RB

CE#, OE#

RESET#

t_RP

Figure 14. RESET# Timings

October 11, 2006 21524D6

Am29LV008B

29

D A T A S H E E T

AC CHARACTERISTICS

Erase/Program Operations

Parameter

Speed Option

JEDEC

t_AVAV

Std

t_WC

t_AS

Description

Write Cycle Time (Note 1)

-70R

-90

90

0

-120

Unit

ns

Min

70

120

t_AVWL

t_WLAX

t_DVWH

t_WHDX

Address Setup Time

Address Hold Time

Data Setup Time

ns

t_AH

45

35

45

0

50

ns

t_DS

ns

t_DH

t_OES

Data Hold Time

ns

Output Enable Setup Time

0

ns

Read Recovery Time Before Write

(OE# High to WE# Low)

t_GHWL

Min

0

ns

t_ELWL

t_WHEH

t_WLWH

t_WHWL

t_WHWH1

t_WHWH2

t_CS

t_CH

CE# Setup Time

Min

Typ

Min

Max

0

ns

µs

sec

µs

ns

CE# Hold Time

t_WP

Write Pulse Width

Write Pulse Width High

35

30

9

50

t_WPH

t_WHWH1Programming Operation (Note 2)

t_WHWH2Sector Erase Operation (Note 2)

0.7

50

0

t_VCS

t_RB

V_CCSetup Time (Note 1)

Recovery Time from RY/BY#

t_BUSYProgram/Erase Valid to RY/BY# Delay

90

Notes:

1. Not 100% tested.

2. See the “Erase and Programming Performance” section for more information.

30

Am29LV008B

21524D6 October 11, 2006

D A T A S H E E T

AC CHARACTERISTICS

Program Command Sequence (last two cycles)

Read Status Data (last two cycles)

t_AS

PA

t_WC

Addresses

555h

PA

t_AH

CE#

OE#

t_CH

t_WHWH1

t_WP

WE#

Data

t_WPH

t_CS

t_DS

t_DH

PD

D_OUT

A0h

Status

t_BUSY

t_RB

RY/BY#

V_CC

t_VCS

Note: PA = program address, PD = program data, D_OUTis the true data at the program address.

Figure 15. Program Operation Timings

October 11, 2006 21524D6

Am29LV008B

31

D A T A S H E E T

AC CHARACTERISTICS

Erase Command Sequence (last two cycles)

Read Status Data

VA

t_AS

SA

t_WC

VA

Addresses

CE#

2AAh

555h for chip erase

t_AH

t_CH

OE#

t_WP

WE#

t_WPH

t_WHWH2

t_CS

t_DS

t_DH

In

Data

Complete

55h

30h

Progress

10 for Chip Erase

t_BUSY

t_RB

RY/BY#

V_CC

t_VCS

Note: SA = sector address (for Sector Erase), VA = Valid Address for reading status data (see “Write Operation Status”).

Figure 16. Chip/Sector Erase Operation Timings

32

Am29LV008B

21524D6 October 11, 2006

D A T A S H E E T

AC CHARACTERISTICS

t_RC

VA

Addresses

VA

t_ACC

t_CE

CE#

t_CH

t_OE

OE#

WE#

t_OEH

t_DF

t_OH

High Z

DQ7

Valid Data

Complement

Status Data

True

DQ0–DQ6

Valid Data

Status Data

True

t_BUSY

RY/BY#

Note: VA = Valid address. Illustration shows first status cycle after command sequence, last status read cycle, and array data

read cycle.

Figure 17. Data# Polling Timings (During Embedded Algorithms)

t_RC

Addresses

CE#

VA

t_ACC

t_CE

VA

t_CH

t_OE

OE#

WE#

t_OEH

t_DF

t_OH

High Z

DQ6/DQ2

RY/BY#

Valid Status

(first read)

Valid Status

Valid Data

(second read)

(stops toggling)

t_BUSY

Note: VA = Valid address; not required for DQ6. Illustration shows first two status cycle after command sequence, last status read

cycle, and array data read cycle.

Figure 18. Toggle Bit Timings (During Embedded Algorithms)

October 11, 2006 21524D6

Am29LV008B

33

D A T A S H E E T

AC CHARACTERISTICS

Enter

Embedded

Erasing

Erase

Suspend

Enter Erase

Suspend Program

Erase

Resume

Erase

Erase Suspend

Read

Erase

Suspend

Program

Erase

Complete

WE#

Erase

Erase Suspend

Read

DQ6

DQ2

Note: The system may use CE# or OE# to toggle DQ2 and DQ6. DQ2 toggles only when read at an address within an

erase-suspended sector.

Figure 19. DQ2 vs. DQ6

Temporary Sector Unprotect

Parameter

JEDEC

Std

Description

All Speed Options

Unit

t_VIDR

V_IDRise and Fall Time (See Note)

Min

500

ns

RESET# Setup Time for Temporary Sector

Unprotect

t_RSP

4

µs

Note: Not 100% tested.

12 V

RESET#

0 or 3 V

t_VIDR

Program or Erase Command Sequence

CE#

WE#

t_RSP

RY/BY#

Figure 20. Temporary Sector Unprotect Timing Diagram

34

Am29LV008B

21524D6 October 11, 2006

D A T A S H E E T

AC CHARACTERISTICS

V_ID

V_IH

RESET#

SA, A6,

A1, A0

Valid*

Sector Protect/Unprotect

60h 60h

Valid*

Status

Verify

40h

Data

Sector Protect: 100 µs

Sector Unprotect: 10 ms

1 µs

CE#

WE#

OE#

* For sector protect, A6 = 0, A1 = 1, A0 = 0. For sector unprotect, A6 = 1, A1 = 1, A0 = 0.

Figure 21. Sector Protect/Unprotect Timing Diagram

October 11, 2006 21524D6

Am29LV008B

35

D A T A S H E E T

AC CHARACTERISTICS

Alternate CE# Controlled Erase/Program Operations

Parameter

Speed Option

JEDEC

t_AVAV

Std

t_WC

t_AS

Description

Write Cycle Time (Note 1)

Address Setup Time

Address Hold Time

-70R

-90

90

0

-120

Unit

ns

Min

70

120

t_AVEL

ns

t_ELAX

t_DVEH

t_EHDX

t_AH

45

35

45

0

50

ns

t_DS

Data Setup Time

ns

t_DH

t_OES

Data Hold Time

ns

Output Enable Setup Time

0

ns

Read Recovery Time Before Write

(OE# High to WE# Low)

t_GHEL

Min

0

ns

t_WLEL

t_EHWH

t_ELEH

t_EHEL

t_WS

t_WH

t_CP

WE# Setup Time

WE# Hold Time

Min

0

ns

CE# Pulse Width

CE# Pulse Width High

35

30

50

t_CPH

Programming Operation

(Note 2)

t_WHWH1

t_WHWH2

Notes:

t_WHWH1

t_WHWH2

Typ

9

µs

Sector Erase Operation (Note 2)

0.7

sec

1. Not 100% tested.

2. See the “Erase and Programming Performance” section for more information.

36

Am29LV008B

21524D6 October 11, 2006

D A T A S H E E T

AC CHARACTERISTICS

555 for program

PA for program

2AA for erase

SA for sector erase

555 for chip erase

Data# Polling

Addresses

PA

t_WC

t_WH

t_AS

t_AH

WE#

OE#

t_GHEL

t_{WHWH1 or 2}

t_CP

CE#

Data

t_WS

t_CPH

t_DS

t_BUSY

t_DH

DQ7#

D_OUT

t_RH

A0 for program

55 for erase

PD for program

30 for sector erase

10 for chip erase

RESET#

RY/BY#

Notes:

1. PA = Program Address, PD = Program Data, DQ7# = complement of the data written to the device, D_OUTis the data written

to the device.

2. Figure indicates the last two bus cycles of the command sequence.

Figure 22. Alternate CE# Controlled Write Operation Timings

October 11, 2006 21524D6

Am29LV008B

37

D A T A S H E E T

ERASE AND PROGRAMMING PERFORMANCE

Parameter

Typ (Note 1)

Max (Note 2)

Unit

s

Comments

Sector Erase Time

Chip Erase Time

Byte Programming Time

0.7

14

9

15

Excludes 00h programming

prior to erasure (Note 4)

s

300

27

µs

Excludes system level

overhead (Note 5)

Chip Programming Time

(Note 3)

9

s

Notes:

1. Typical program and erase times assume the following conditions: 25°C, 3.0 V V_CC, 1,000,000 cycles. Additionally,

programming typicals assume checkerboard pattern.

2. Under worst case conditions of 90°C, V_CC= 2.7 V, 1,000,000 cycles.

3. The typical chip programming time is considerably less than the maximum chip programming time listed, since most bytes

program faster than the maximum program times listed.

4. In the pre-programming step of the Embedded Erase algorithm, all bytes are programmed to 00h before erasure.

5. System-level overhead is the time required to execute the four-bus-cycle sequence for the program command. See Table 5

for further information on command definitions.

6. The device has a minimum erase and program cycle endurance of 1,000,000 cycles.

LATCHUP CHARACTERISTICS

Description

Min

Max

Input voltage with respect to V_SSon all pins except I/O pins

(including A9, OE#, and RESET#)

–1.0 V

12.5 V

Input voltage with respect to V_SSon all I/O pins

V_CCCurrent

–1.0 V

V_CC+ 1.0 V

+100 mA

–100 mA

Includes all pins except V_CC. Test conditions: V_CC= 3.0 V, one pin at a time.

TSOP PIN CAPACITANCE

Parameter

Symbol

Parameter Description

Input Capacitance

Test Setup

V_IN= 0

Typ

6

Max

7.5

12

Unit

pF

C_IN

C_OUT

C_IN2

Output Capacitance

Control Pin Capacitance

V_OUT= 0

V_IN= 0

8.5

7.5

pF

9

pF

Notes:

1. Sampled, not 100% tested.

2. Test conditions T_A= 25°C, f = 1.0 MHz.

DATA RETENTION

Parameter

Test Conditions

Min

10

Unit

Years

150°C

125°C

Minimum Pattern Data Retention Time

20

38

Am29LV008B

21524D6 October 11, 2006

D A T A S H E E T

PHYSICAL DIMENSIONS*

TS 040—40-Pin Standard TSOP

Dwg rev AA; 10/99

* For reference only. BSC is an ANSI standard for Basic Space Centering.

October 11, 2006 21524D6

Am29LV008B

39

D A T A S H E E T

REVISION SUMMARY

Revision A (October 1997)

Revision C (January 1999)

First release.

Global

Updated for CS39S process technology.

Revision B (January 1998)

Distinctive Characteristics

Added:

Changed typical read and program/erase current

specifications.

■ 20-year data retention at 125°C

— Reliable operation for the life of the system

DC Characteristics—CMOS Compatible

Device now has a guaranteed minimum endurance of

1,000,000 write cycles.

I

, I

: Added Note 2 “Maximum

Figure of In-System Sector Protect/Unprotect

Algorithm

CC1 CC2 CC3 CC4 CC5

I

specifications are tested with V = V

”.

CCmax

CC

Corrected A6 to 0, Changed wait specification to 150 µs

on sector protect and 15 ms on sector unprotect.

I

, I

: Deleted V = V

.

CCmax

CC3 CC4

CC

Revision D (November 19, 1999)

AC Characteristics—Figure 15. Program

Operations Timing and Figure 16. Chip/Sector

Erase Operations

DC Characteristics

Changed typical read and program/erase current

specifications.

AC Characteristics

Deleted t

high.

and changed OE# waveform to start at

GHWL

Alternate CE# Controlled Erase/Program Operations:

Changed tCP to 35 ns for 70R, 80, and 90 speed options.

Physical Dimensions

Erase and Programming Performance

Replaced figures with more detailed illustrations.

Device now has a guaranteed minimum endurance of

1,000,000 write cycles.

Revision D+1 (August 14, 2000)

Global

Revision B+1 (March 1998)

Figure of In-System Sector Protect/Unprotect

Algorithms

Deleted 80 ns speed option.

Ordering Information

In the sector protect algorithm, added a “Reset

PLSCNT=1” box in the path from “Protect another

sector?” back to setting up the next sector address.

Deleted burn-in option.

Revision D+2 (November 10, 2000)

DC Characteristics

Command Definitions

Changed Note 1 to indicate that OE# is at V for the

listed current.

Reset Command: Deleted reference to Figure 14, RE-

SET# Timings, which is only applicable to the hardware

reset function.

IH

AC Characteristics

Erase/Program Operations; Alternate CE# Controlled

Erase/Program Operations: Corrected the notes refer-

Revision D+3 (June 11, 2004)

Ordering Information

ence for t

and t

. These parameters are

WHWH1

WHWH2

Added Pb-Free OPNs.

100% tested. Corrected the note reference for t

This parameter is not 100% tested.

.

VCS

Revision D4 (February 21, 2006)

Global

Temporary Sector Unprotect Table

Added note reference for t

100% tested.

. This parameter is not

VIDR

Removed Reverse TSOP option.

Figure 21, Sector Protect/Unprotect Timing

Diagram

Revision D5 (September 12, 2006)

Erase and Program Operations table

A valid address is not required for the first write cycle;

only the data 60h.

Changed t

to a maximum specification.

BUSY

Erase and Programming Performance

In Note 2, the worst case endurance is now 1 million cycles.

40

Am29LV008B

21524D6 October 11, 2006

D A T A S H E E T

Revision D6 (October 11, 2006)

Global

Added notice on product availability.

Colophon

The products described in this document are designed, developed and manufactured as contemplated for general use, including without limita-

tion, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as con-

templated (1) for any use that includes fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the

public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility,

aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for

any use where chance of failure is intolerable (i.e., submersible repeater and artificial satellite). Please note that Spansion Inc. will not be liable

to you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor

devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design

measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating

conditions. If any products described in this document represent goods or technologies subject to certain restrictions on export under the Foreign

Exchange and Foreign Trade Law of Japan, the US Export Administration Regulations or the applicable laws of any other country, the prior au-

thorization by the respective government entity will be required for export of those products.

Trademarks

marks of Advanced Micro Devices, Inc. ExpressFlash is a trademark of Advanced Micro Devices, Inc. Product names used in this publication are

for identification purposes only and may be trademarks of their respective companies.

trademarks of Spansion Inc. Other names are for informational purposes only and may be trademarks of their respective owners.

October 11, 2006 21524D6

Am29LV008B

41


型号：	AM29LV008BB-120EK
厂家：	AMD
描述：	8 Megabit (1 M x 8-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory 8兆位（ 1一M× 8位） CMOS 3.0伏只引导扇区闪存闪存内存集成电路光电二极管
文件：	总41页 (文件大小：720K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

AM29LV008BB-120EK [AMD]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB

SI9137LG

SI9122E