PD6080J5050S2 [ANAREN]
Ultra Low Profile 0805 Power Divider 50ヘ to 50ヘ; 超薄型0805功分50ヘ50ヘ型号: | PD6080J5050S2 |
厂家: | ANAREN MICROWAVE |
描述: | Ultra Low Profile 0805 Power Divider 50ヘ to 50ヘ |
文件: | 总6页 (文件大小:224K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Model PD6080J5050S2
Rev B
Ultra Low Profile 0805 Power Divider
50Ω to 50Ω
Description
The PD6080J5050S2 is a low profile, sub-miniature Wilkinson power divider in an
easy to use surface mount package. The PD6080J5050S2 is ideal for high volume
manufacturing and delivers higher performances than traditional printed and lumped
element solutions. The PD6080J5050S2 is matched to 50 Ω and has a height
profile of 0.5 mm which is ideal for high level integrations in the following markets:
RFID, fixed satellite, and mobile satellite. The PD6080J5050S2 does not include the
resistive element and therefore, requires an external resistor for operation. The
PD6080J5050S2 is available on tape and reel for high volume manufacturing pick
and place.
Detailed Electrical Specifications: Specifications subject to change without notice.
ROOM (25°C)
Features:
Parameter
Min.
Typ.
Max
Unit
MHz
Ω
• 6000-8000 MHz
Frequency
6000
8000
• 15 dB Isolation (output ports)
• Good Return Loss
• 0.5mm Height Profile
• 50ꢀ Input / 50ꢀ Outputs
• Low Insertion Loss
• Surface Mountable
• Tape & Reel
Input Port Impedance
Output Port Impedance
Return Loss
50
50
12
0.6
0.2
2
Ω
9
dB
Insertion Loss*
0.9
0.5
5
dB
Amplitude Balance
Phase Balance
dB
Degrees
dB
• Non-conductive Surface
• RoHS Compliant
Isolation (Output Ports)
Power Handling
Operating Temperature
12
15
2
Watts
ºC
-55
+85
* Insertion Loss stated at room temperature (Insertion Loss is approximately 0.1 dB higher at +85 ºC)
Outline Drawing
Top View (Near-side)
Side View
Bottom View (Far-side)
.079±.004
[2.00±0.10]
2X .026
[0.65]
.021±.002
[0.53±0.05]
1
2
3
4
.039
[0.98]
6X .009
[0.22]
.049±.004
[1.25±0.10]
Orientation
Marker Denotes
Pin Location
6
5
Orientation
Marker Denotes
Pin Location
6X .012
[0.30]
Pin Designation
1
2
3
4
5
6
GND
Input
GND
Output 1
GND
Dimensions are in Inches [Millimeters]
Mechanical Outline
Tolerances are Non-Cumulative
Output 2
USA/Canada:
Toll Free:
(315) 432-8909
(800) 411-6596
+44 2392-232392
Available on Tape
and Reel for Pick and
Place Manufacturing.
Europe:
Model PD6080J5050S2
Rev B
Typical Broadband Performance: 500 MHz. to 9.0 GHz.
Return Loss - Input
Insertion Loss
0
-3
0
-3
-6
-6
-9
-9
-12
-15
-18
-21
-24
-27
-30
-33
-36
-12
-15
-18
-21
-24
-27
-30
-33
-36
Frequency [MHz]
Frequency [MHz]
Amplitude Balance
Phase Balance
20
15
10
5
2
1.5
1
0.5
0
0
-0.5
-1
-5
-10
-15
-20
-1.5
-2
Frequency [MHz]
Frequency [MHz]
Isolation
0
-3
-6
-9
-12
-15
-18
-21
-24
-27
-30
-33
-36
Frequency [MHz]
USA/Canada:
Toll Free:
Europe:
(315) 432-8909
(800) 411-6596
+44 2392-232392
Available on Tape and
Reel for Pick and Place
Manufacturing.
Model PD6080J5050S2
Rev B
Typical Performance: 5900 MHz. to 8100 MHz.
Return Loss - Input
Insertion Loss
0.0
-0.3
-0.6
-0.9
-1.2
-1.5
-1.8
-2.1
-2.4
-2.7
-3.0
-3.3
-3.6
0
-3
-6
-9
-12
-15
-18
-21
-24
-27
-30
-33
-36
Frequency [MHz]
Frequency [MHz]
Amplitude Balance
Phase Balance
20
15
10
5
2
1.5
1
0.5
0
0
-5
-0.5
-1
-10
-15
-20
-1.5
-2
Frequency [MHz]
Isolation
Frequency [MHz]
0
-3
-6
-9
-12
-15
-18
-21
-24
-27
-30
-33
-36
Frequency [MHz]
USA/Canada:
Toll Free:
(315) 432-8909
(800) 411-6596
+44 2392-232392
Available on Tape
and Reel for Pick and
Place Manufacturing.
Europe:
Model PD6080J5050S2
Rev B
Mounting Configuration:
In order for Xinger surface mount components to work optimally, the proper impedance transmission lines must be
used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may not meet
published specifications.
An example of the PCB footprint used in the testing of these parts is shown below. In specific designs, the
transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying
pick and place equipment tolerances. In addition, since the PD6080J5050S2 is a Wilkinson power divider, an
external 0603 100ꢀ resistor must be mounted in locations R1 as shown in the Figure below.
All of the Xinger components are constructed from ceramic filled PTFE composites which possess excellent electrical
and mechanical stability having X and Y thermal coefficient of expansion (CTE) of 17 ppm/oC.
Pad Footprint w/ 0603 Resistor Location
6X .014
[0.35]
4X .012
[0.30]
6X .010
[0.25]
.033
[0.85]
6X .002
[0.05]
Plated thru
holes to
ground
R1
Circuit Pattern
3X Transmission
Line
Footprint Pad (s)
Solder Resist
Dimensions are in Inches [Millimeters]
Mounting Footprint
USA/Canada:
Toll Free:
Europe:
(315) 432-8909
(800) 411-6596
+44 2392-232392
Available on Tape and
Reel for Pick and Place
Manufacturing.
Model PD6080J5050S2
Rev B
Packaging and Ordering Information
Parts are available in reels and are packaged per EIA 481-2. Parts are oriented in tape and reel as shown below. Minimum order
quantities are 4000 per reel. See Model Numbers below for further ordering information.
ØA
ØC
ØD
TABLE 1
REEL DIMENSIONS (inches [mm])
B
QUANTITY/REEL
4000
ØA
B
7.00 [177.8]
0.32 [8.0]
ØC
ØD
2.0 [50.8]
0.512 [13.0]
USA/Canada:
Toll Free:
(315) 432-8909
(800) 411-6596
+44 2392-232392
Available on Tape
and Reel for Pick and
Place Manufacturing.
Europe:
Model PD6080J5050S2
Rev B
USA/Canada:
Toll Free:
Europe:
(315) 432-8909
(800) 411-6596
+44 2392-232392
Available on Tape and
Reel for Pick and Place
Manufacturing.
相关型号:
PD6080J5050S2HF
Splitter, 6000MHz Min, 8000MHz Max, 0.9dB Insertion Loss-Max, HALOGEN FREE AND ROHS COMPLIANT, SUB-MINIATURE, SURFACE MOUNT, CERAMIC, 0805, 6 PIN
ANAREN
©2020 ICPDF网 联系我们和版权申明