RFP-10-50TVR [ANAREN]

Flanged Terminations; 法兰连接端接
RFP-10-50TVR
型号: RFP-10-50TVR
厂家: ANAREN MICROWAVE    ANAREN MICROWAVE
描述:

Flanged Terminations
法兰连接端接

文件: 总2页 (文件大小:498K)
中文:  中文翻译
下载:  下载PDF数据表文档文件
Model RFP-10-50TVR  
Flanged Terminations  
10 Watts, 50  
General Specifications  
Resistive Element:  
Thick film  
Substrate:  
Cover:  
Beryllium oxide ceramic  
Alumina ceramic  
Mounting Flange:  
Copper, nickel plated per  
QQ-N-290  
Lead(s):  
99.99% pure silver (.005” thk)  
Features  
• DC - 4.0 GHz  
Electrical Specifications  
• 10 Watts  
Resistance Value:  
Frequency Range:  
Power:  
50 ohms, 5%  
DC - 4.0 GHz  
10 Watts  
1.25:1  
• BeO Ceramic  
• Welded Silver Leads  
V.S.W.R.:  
• Non-Nichrome Resistive  
Element  
Notes: Tolerance is .010, unless otherwise specified. Operating  
temperature is -55°C to +150°C (see chart). Designed to meet or  
exceed applicable portions of MIL-E-5400. All dimensions are in  
inches. Lead length 0.15” minimum.  
• Low VSWR  
Specifications subject to change without notice.  
• 100% Tested  
Outline Drawing  
.200  
.100  
.062  
.116 DIA.  
50  
.050  
.100  
.120 MAX.  
VER. 12/5/01  
Sales Desk USA: Voice: (800) 544-2414 Fax: (315) 432-9121  
Sales Desk Europe: Voice: (+44) 23 92 232392 Fax: (+44) 23 92 251369  
1
Model RFP-10-50TVR  
Typical Performance  
Suggested Mounting Procedures  
Power Derating  
.025 MIN.  
(2 PLACES)  
BOARD LOWER  
THAN LEAD.  
BOARD EVEN  
WITH LEAD.  
BOARD LOWER  
THAN LEAD.  
BOARD HIGHER  
THAN LEAD.  
100  
SUGGESTED STRESS RELIEF METHODS  
SCALE:  
NOT RECOMMENDED APPLICATION  
SCALE:  
75  
50  
1. Make sure that the devices are mounted on flat surfaces  
(.001” under the device) to optimize the heat transfer.  
25  
0
2. Drill & tap the heatsink for the appropriate thread size to be  
used.  
3. Coat heatsink with a minimum amount of high quality  
silicone grease (.001” max. thickness).  
25  
50  
75  
100  
125  
150  
CASE TEMPERATURE — °C  
4. Position device on mounting surface and secure using  
socket head screws, flat & split washers. Torque screws to  
the appropriate value. Make sure that the device is flat  
against the heatsink. (Care should be taken to avoid  
upward pressure of the leads towards the lid).  
5. Solder leads in place using an SN63 type solder with a  
controlled temperature iron (210°C).  
Sales Desk USA: Voice: (800) 544-2414 Fax: (315) 432-9121  
2
Sales Desk Europe: Voice: (+44) 23 92 232392 Fax: (+44) 23 92 251369  

相关型号:

RFP-10-50TVV

RF/Microwave Termination, 0MHz Min, 4000MHz Max, 50ohm
ANAREN

RFP-100-100RW

Flanged Resistors 100 Watts, 100 ohm
ANAREN

RFP-100-100RW-S

Full Flange Resistor 100 Watts, 100Ohms
ANAREN

RFP-100-10AE-S

Full Flange Attenuators 100 Watts
ANAREN

RFP-100-1AE-S

Full Flange Attenuators 100 Watts
ANAREN

RFP-100-20AE-S

Full Flange Attenuators 100 Watts
ANAREN

RFP-100-22AE-S

Full Flange Attenuators 100 Watts
ANAREN

RFP-100-2AE-S

Full Flange Attenuators 100 Watts
ANAREN

RFP-100-30AE-S

Full Flange Attenuators 100 Watts
ANAREN

RFP-100-3AE-S

Full Flange Attenuators 100 Watts
ANAREN

RFP-100-4AE-S

Full Flange Attenuators 100 Watts
ANAREN

RFP-100-4AMZ

Fixed Attenuator, 0MHz Min, 1000MHz Max
ANAREN