APL5101-17B [ANPEC]
150mA, 4mA Quiescent Current Regulator; 150毫安， 4毫安静态电流稳压器
| 型号： | APL5101-17B |
| 厂家： | 
ANPEC ELECTRONICS COROPRATION |
| 描述： | 150mA, 4mA Quiescent Current Regulator |
| 文件： | 总18页 (文件大小：265K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
APL5101/2
150mA, 4mA Quiescent Current Regulator
General Description
Features
The APL5101/2 are micro-power and ultra low dropout
linear regulators, which operate from 2V to 6V input volt-
age and deliver up to 150mA. Typical dropout voltage is
only 200mV at 150mA loading. Designed for use in bat-
tery-powered system, the low 4mA quiescent current
makes it an ideal choice. Design with an internal P-chan-
nel MOSFET pass transistor, the APL5101/2 maintain a
low supply current, independent of the load current and
dropout voltage.
·
·
Ultra Low Quiescent Current: 4mA
Ultra Low Dropout Voltage:
200mV@3.3V/150mA
·
Fixed Output Voltages: 1.2V~3.5V,
Steps 100mV
·
·
·
·
·
·
·
·
Guaranteed 150mA Output Current
Stable with 1mF Output Capacitor
Ceramic Capacitor can be used
Current-Limit Protection
Other features include thermal-shutdown protection and
current limit protection to ensure specified output current
and controlled short-circuit current. The APL5101/2 regu-
lators come in a miniature SOT-23, SOT-23-5, and SOT-
89 packages.
Controlled Short Circuit Current: 50mA
Build-in Thermal Protection
SOT-23, SOT-23-5, and SOT-89 Packages
Lead Free and Green Devices Available
(RoHS Compliant)
Applications
·
·
·
Hand-Held Equipment
RTC or CMOS Backup Power
Battery Powered Equipment
Pin Configuration
SOT-23-5
SOT-23
VIN
1
2
3
5
4
VOUT
VOUT
1
GN
D
VIN
3
NC
2
GND
SHDN
APL5101
APL5101
SOT-89
SOT-23
SOT-23-5
G
ND
VIN
1
VOUT
1
2
3
5
4
GND
VIN
3
VOUT
NC
2
NC
GND VIN
VOUT
APL5101
APL5102
APL5102
ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise
customers to obtain the latest version of relevant information to verify before placing orders.
Copyright ã ANPEC Electronics Corp.
1
www.anpec.com.tw
Rev. A.5 - Jul., 2013
APL5101/2
Ordering and Marking Information
Package Code
A : SOT-23
APL5101/2 -
B : SOT-23-5
D : SOT-89
Operating Ambient Temperature Range
Assembly Material
Handling Code
I : -40 to 85 oC
Handling Code
TR : Tape & Reel
Voltage Code :
12 : 1.2V ~ 35 : 3.5V
Assembly Material
L : Lead Free Device
G: Halogen and Lead Free Device
Temperature Range
Package Code
Voltage Code
APL5101
XXXXX12
105X
APL5101 -12 A/B:
APL5102 -12 A/B:
XXXXX - Date Code : 12 - 1.2V
X - Date Code : 5 - 1.2V
APL5101 -12 D :
APL5102
XXXXX12
AB5X
X - Date Code : 5 - 1.2V
APL5102 -12 D :
XXXXX - Date Code : 12 - 1.2V
Note: ANPEC lead-free products contain molding compounds/die attach materials and 100% matte tin plate termination finish; which
are fully compliant with RoHS. ANPEC lead-free products meet or exceed the lead-free requirements of IPC/JEDEC J-STD-020D for
MSL classification at lead-free peak reflow temperature. ANPEC defines “Green” to mean lead-free (RoHS compliant) and halogen
free (Br or Cl does not exceed 900ppm by weight in homogeneous material and total of Br and Cl does not exceed 1500ppm by
weight).
SOT-23 and SOT-23-5 packages
Product Name
APL5101-12A/B
APL5101-13A/B
APL5101-14A/B
APL5101-15A/B
APL5101-16A/B
APL5101-17A/B
APL5101-18A/B
APL5101-19A/B
APL5101-20A/B
APL5101-21A/B
APL5101-22A/B
APL5101-23A/B
APL5101-24A/B
APL5101-25A/B
APL5101-26A/B
APL5101-27A/B
APL5101-28A/B
APL5101-29A/B
APL5101-30A/B
APL5101-31A/B
APL5101-32A/B
APL5101-33A/B
APL5101-34A/B
APL5101-35A/B
Marking
105X
107X
108X
109X
10AX
10BX
10CX
10DX
10EX
10FX
10GX
10HX
10IX
Product Name
APL5102-12A/B
APL5102-13A/B
APL5102-14A/B
APL5102-15A/B
APL5102-16A/B
APL5102-17A/B
APL5102-18A/B
APL5102-19A/B
APL5102-20A/B
APL5102-21A/B
APL5102-22A/B
APL5102-23A/B
APL5102-24A/B
APL5102-25A/B
APL5102-26A/B
APL5102-27A/B
APL5102-28A/B
APL5102-29A/B
APL5102-30A/B
APL5102-31A/B
APL5102-32A/B
APL5102-33A/B
APL5102-34A/B
APL5102-35A/B
Marking
AB5X
AB7X
AB8X
AB9X
ABAX
ABBX
ABCX
ABDX
ABEX
ABFX
ABGX
ABHX
ABIX
10JX
10KX
10LX
10MX
10NX
10OX
10PX
10QX
10RX
10SX
10TX
ABJX
ABKX
ABLX
ABMX
ABNX
ABOX
ABPX
ABQX
ABRX
ABSX
ABTX
Copyright ã ANPEC Electronics Corp.
2
www.anpec.com.tw
Rev. A.5 - Jul., 2013
APL5101/2
Absolute Maximum Ratings
Symbol
Parameter
Rating
6.5
Unit
V
VIN,VOUT Input Voltage or Out Voltage
SHDN
VOUT Shutdown Control Pin
6.5
V
Thermal Resistance-Junction to Ambient
SOT-23
SOT-23-5
SOT-89
260
260
180
RTH JA
,
°C /W
°C /W
Thermal Resistance-Junction to Ambient
SOT-23
SOT-23-5
SOT-89
130
130
90
RTH,JC
PD
TJ
Power Dissipation
Internally Limited
-40 to 150
-65 to +150
260
W
°C
°C
°C
Junction Temperature Range
Storage Temperature Range
TSTG
TL
Maximum Lead Soldering Temperature, 10 Seconds
Electrical Characteristics
Unless otherwise noted these specificatons apply over full temperature, VIN = 5V, CIN = COUT = 1mF, TA = -40 to 85°C. Typical values
refer to TA = 25°C.
APL5101/2
Symbol
Parameter
Test Conditions
Unit
Min.
Typ.
Max.
VIN
Input Voltage
2
-2
-
6
2
V
%
Output Voltage Accuracy
Output Voltage Range
Current-Limit
VIN = 5V
VIN = 5V
-
-
VOUT
ILIMIT
1.2
250
-
3.5
370
7
V
300
4
mA
IOUT = 0mA
Quiescent Current
IQ
mA
IOUT = 150mA
VSHDN = High
-
4
10
Shutdown Supply Current
Load Current
-
150
-
0.1
-
1
-
IOUT
mA
mV
mV
REGLINE Line Regulation
REGLOAD Load Regulation
VOUT + 0.5V<VIN<6V, IOUT = 10mA
VIN = 5V, 0Ma<IOUT<IMAX
VOUT = 1.4V, IOUT = 150mA
VOUT = 1.8V, IOUT = 150mA
VOUT = 3.3V, IOUT = 150mA
F = 1kHz, COUT = 1mF, IOUT = 10mA
VOUT = 0V
2
10
-
-
15
1000
600
200
40
30
1300
900
300
-
VDROP
Dropout Voltage (Note)
mV
-
-
PSRR
ISHORT
Ripple Rejection
30
-
dB
Short Circuit Current
55
-
mA
Copyright ã ANPEC Electronics Corp.
3
www.anpec.com.tw
Rev. A.5 - Jul., 2013
APL5101/2
Electrical Characteristics (Cont.)
Unless otherwise noted these specificatons apply over full temperature, VIN = 5V, CIN = COUT = 1mF, TA = -40 to 85°C. Typical values
refer to TA = 25°C.
APL5101/2
Symbol
Parameter
Test Conditions
Unit
Min.
Typ.
Max.
F = 22Hz to 80kHz,
COUT = 1mF, IOUT = 10mA
en
Noise
-
200
250
m
VRMS
ISHDN
VSHDN
TEXIT
Shutdown Input Bias Current
High Threshold Voltage
Low Threshold Voltage
Shutdown Exit Delay
VSHDN = Low
-
0.1
1
VIN+0.3
0.4
m
A
1.6
-0.3
1.5
120
-
-
V
V
W
2
2.5
mS
°C
VOUT = 90%, RLOAD = 25
Over Temperature Shutdown
135
-
OTS
Over Temperature Shutdown
Hysteresis
10
-
20
30
°C
Output Voltage Temperature
Coefficient
TC
TA = -40°C ~ 100°C
100
200
ppm/°C
Output Capacitor
ESR
1
-
-
10
m
F
COUT
10
1000
W
m
Note: Dropout voltage definition:VIN-VOUT when VOUT is 2% below the value of VOUT for VIN= VOUT+1V.
Pin Description
PIN
I/O
FUNCTION
NO.
1
NAME
VIN
I
Voltage supply input pin
GND pin
2
GND
SHDN
NC
3
I
Shutdown control pin, high = off, low = normal
Not connected
4
5
VOUT
O
Regulator output pin
Block Diagram
V IN
C u r r e n t
L imit
R e ference
V o lta g e
SHD N
S h u tdown
L o g ic
_
+
V O UT
T h e r m a l
S h u tdown
G ND
APL5101/2
Copyright ã ANPEC Electronics Corp.
4
www.anpec.com.tw
Rev. A.5 - Jul., 2013
APL5101/2
Typical Application Circuit
APL5101/2
VIN
VOUT
SHDN
COUT
CIN
GND
1m
1m
F
F
Typical Operating Characteristics
Quiescent Current vs. Input Voltage
Quiescent Current vs. Output Current
5
4
3.5
3
V
OUT=3.3V
4.5
4
V
IN=5V
3.5
3
2.5
2
2.5
2
1.5
1
1.5
1
0.5
0
0.5
0
0
25
50
75
100
125
150
0
1
2
3
4
5
6
Input Voltage(V)
Output Current(mA)
Copyright ã ANPEC Electronics Corp.
5
www.anpec.com.tw
Rev. A.5 - Jul., 2013
APL5101/2
Typical Operating Characteristics (Cont.)
Output Voltage vs. Input Voltage
Quiescent Current vs. Ambient Temperature
4
3.5
3
3.5
3
IOUT=0mA
V
OUT=1.4V
2.5
2
2.5
2
1.5
1
1.5
1
0.5
0
0.5
0
0
1
2
3
4
5
6
-40
-20
0
20
40
60
80
100
Input Voltage(V)
Ambient Temperature(°C)
Dropout Voltage vs. Output Current
PSRR vs. Frequency
+0
-10
-20
-30
-40
1200
1000
800
600
400
200
0
100mA
T
TT T
V
OUT=1.2V
50mA
-50
-60
-70
1mA
-80
-90
V
OUT=3.3V
125
-100
10
100
1k
10k
100k
0
25
50
75
100
150
Frequency(Hz)
Output Current(mA)
Copyright ã ANPEC Electronics Corp.
6
www.anpec.com.tw
Rev. A.5 - Jul., 2013
APL5101/2
Typical Operating Characteristics (Cont.)
Load Transient Response
Load Transient Response
V
OUT=1.4V
V
OUT=3.3V
(50mV/div)
(50mV/div)
IL=1~150mA
IL=1~150mA
Time(0.5ms/div)
Time(0.5ms/div)
Line Transient Response
Line Transient Response
V
IN(4.5V~5.5V)
V
IN(4.5V~5.5V)
V
OUT=1.4V(200mV/div)
V
I
OUT=3.3V(200mV/div)
OUT=10mA
COUT=1mF
IOUT=10mA
C
OUT=1mF
Time(0.1ms/div)
Time(0.1ms/div)
Copyright ã ANPEC Electronics Corp.
7
www.anpec.com.tw
Rev. A.5 - Jul., 2013
APL5101/2
Typical Operating Characteristics (Cont.)
Current Limit vs. Input Voltage
Output Voltage vs. Ambient Temperature
1.398
1.396
1.394
1.392
1.39
400
350
300
250
200
150
100
50
V
OUT(3.3V), T =25°C
A
V
OUT(1.4V), T =25°C
A
IL=0mA
V
OUT(3.3V), T
A=85°C
V
OUT(1.4V), T
A=85°C
1.388
1.386
1.384
0
2.5
3
3.5
4
4.5
5
5.5
6
-40
-20
0
20
40
60
80
100
120
Input Volatge(V)
Ambient Temperature(°C)
Power Dissipation vs. Ambient Temperature
Output Voltage vs. Temperature
3.312
3.31
0.6
0.5
0.4
0.3
0.2
0.1
0
3.308
3.306
3.304
3.302
3.3
IL=0mA
SOT-89
SOT-23
3.298
3.296
-40
-20
0
20
40
60
80
100
120
25
50
75
100
125
Ambient Temperature(°C)
Ambient Temperature(°C)
Copyright ã ANPEC Electronics Corp.
8
www.anpec.com.tw
Rev. A.5 - Jul., 2013
APL5101/2
Application Information
Operating Region and Power Dissipation
Capacitor Selection and Regulation Stability
The thermal resistance of the case and circuit board,
ambient and junction air temperature, and the rate of air
flow all control the APL5101/2’s maximum power
dissipation. The power dissipation across the device is
P = IOUT (VIN-VOUT). The maximum power dissipation is:
The APL5101/2 use at least a 1mF capacitor on the input.
This capacitor can use Aluminum, Tantalum or Ceramic
capacitors. Input capacitor with large value and low ESR
provides better PSRR and line transient response. The
output capacitor also can use Aluminum, Tantalum or
Ceramic capacitor, and its proper values is recommended
1mF, ESR must be above 10mW Large output capacitor
values can reduce noise and improve load-transient
response, stability, and PSRR. With X5R and Y5V
dielectrics, 1mF is sufficient at all operating temperatures.
The selection of output capacitor is important because it with
COUT forms a zero to provide the sufficient phase margin.
PMAX = (TJ-TA) / (qJC +qCA
)
where TJ-TA is the temperature difference between the
junction and ambient air. qJC is the thermal resistance of
the package, qCA is the thermal resistance through the
printed circuit board, copper traces, and other materials
to the surrounding air. The GND pin provides an electrical
connection to ground and channeling heat away. The
printed circuit board (PCB) forms a heat sink and dissi-
pates most of the heat into ambient air.
Input-Output (Dropout) Voltage
The minimum input-output voltage differential (dropout)
determines the lowest usable supply voltage. The drop-
out voltage is the function of drain-to-source on resis-
tance multiplied by the load current.
Recommanded Minimum Footprint
SOT-23
0.037
Current Limit and Short Circuit
APL5101/2 include a current-limit circuitry for this lin-
ear regulator. The current limit protection, which sense
the current flows the P-channel MOSFET, and controls
the output voltage. The point where limiting occurs is
IOUT=300mA. When output is shorted to ground, the
APL5101/2 will keep short circuit current at 50mA.This
design is a method for an indefinite amount of time with-
out damaging to the part.
0.024
0.074
Unit : Inch
Thermal Protection
SOT-23-5
Thermal protection limits total power dissipation in the
APL5101/2. When the junction temperature exceeds TJ =
+135°C, the thermal sensor generate a logic signal to turn
off the pass transistor and let IC to cool. When the IC’s
junction temperature cools by 20°C, the thermal sen-
sor will turn the pass transistor on again, resulting in a
pulsed output during continuous thermal protection. Ther-
mal protection is designed to protect the IC in the event of
fault conditions. For continual operation, the junction tem-
perature do not exceed TJ=+125oC.
0.076
0.038
0.02
Unit : Inch
Copyright ã ANPEC Electronics Corp.
9
www.anpec.com.tw
Rev. A.5 - Jul., 2013
APL5101/2
Application Information (Cont.)
Recommanded Minimum Footprint (Cont.)
SOT-89
0.076
0.059
0.022
Unit : Inch
Copyright ã ANPEC Electronics Corp.
10
www.anpec.com.tw
Rev. A.5 - Jul., 2013
APL5101/2
Package Information
SOT-23
D
e
SEE
VIEW A
c
b
e1
GAUGE PLANE
SEATING PLANE
L
VIEW A
SOT-23
S
Y
M
B
O
MILLIMETERS
MIN. MAX.
INCHES
MIN.
MAX.
0.057
0.006
0.051
0.020
0.009
L
A
1.45
0.15
1.30
0.50
0.22
0.000
0.035
0.012
0.003
A1
A2
b
0.00
0.90
0.30
0.08
c
D
3.10
3.00
1.80
0.106
0.102
0.055
0.122
0.118
0.071
2.70
2.60
1.40
E
E1
e
0.95 BSC
1.90 BSC
0.037 BSC
0.075 BSC
e1
L
0.012
0.024
0.30
0.60
0
0
8
0
8
Note : Dimension D and E1 do not include mold flash, protrusions or gate
burrs. Mold flash, protrusion or gate burrs shall not exceed 10 mil
per side.
Copyright ã ANPEC Electronics Corp.
Rev. A.5 - Jul., 2013
11
www.anpec.com.tw
APL5101/2
Package Information
SOT-23-5
D
e
SEE
VIEW A
b
c
e1
GAUGE PLANE
SEATING PLANE
L
VIEW A
SOT-23-5
S
Y
M
B
O
MILLIMETERS
INCHES
MIN.
MAX.
1.45
0.15
1.30
0.50
0.22
MIN.
MAX.
0.057
0.006
0.051
0.020
0.009
0.122
0.118
0.071
L
A
0.000
0.035
0.012
0.003
0.016
0.102
0.055
A1
A2
b
0.00
0.90
0.30
0.08
c
D
3.10
3.00
1.80
2.70
2.60
1.40
E
E1
e
e1
L
0.95 BSC
1.90 BSC
0.037 BSC
0.075 BSC
0.012
0.024
0.30
0.60
0
0
8
0
8
Note : 1. Follow JEDEC TO-178 AA.
2. Dimension D and E1 do not include mold flash, protrusions or gate
burrs. Mold flash, protrusion or gate burrs shall not exceed 10 mil
per side.
Copyright ã ANPEC Electronics Corp.
Rev. A.5 - Jul., 2013
12
www.anpec.com.tw
APL5101/2
Package Information
SOT-89
D
A
C
D1
e
e1
B
B1
SOT-89
S
Y
M
B
O
L
MILLIMETERS
MIN.
INCHES
MAX.
1.60
0.56
0.48
0.44
4.60
MIN.
MAX.
0.063
0.022
0.019
0.017
0.181
0.072
0.102
0.090
A
1.40
0.44
0.36
0.35
4.40
0.055
0.017
0.014
0.014
0.173
0.064
0.090
0.084
B
B1
C
D
D1
E
1.62
2.29
1.83
2.60
E1
e
2.13
2.29
1.50 BSC
3.00 BSC
0.059 BSC
0.118 BSC
e1
H
0.155
0.035
0.167
0.047
3.94
0.89
4.25
1.20
L
Note : Follow JEDEC TO-243 AA.
Copyright ã ANPEC Electronics Corp.
13
www.anpec.com.tw
Rev. A.5 - Jul., 2013
APL5101/2
Carrier Tape & Reel Dimensions
P0
P2
P1
OD0
A
K0
A0
A
OD1
B
B
SECTION A-A
SECTION B-B
d
T1
Application
SOT-23-3
Application
SOT-23-5
Application
SOT-89
A
H
T1
C
d
D
W
E1
F
8.4+2.00 13.0+0.50
-0.00 -0.20
178.0±
2.00
50 MIN.
1.5 MIN. 20.2 MIN. 8.0±0.30 1.75±0.10 3.5±0.05
P0
P1
P2
D0
D1
1.0 MIN.
d
T
A0
B0
K0
1.5+0.10
-0.00
0.6+0.00
-0.40
4.0±0.10 4.0±0.10 2.0±0.05
3.20±0.20 3.10±0.20 1.50±0.20
A
H
50 MIN.
P1
T1
C
D
W
E1
F
8.4+2.00 13.0+0.50
-0.00 -0.20
178.0±
2.00
1.5 MIN. 20.2 MIN. 8.0±0.30 1.75±0.10 3.5±0.05
P0
P2
D0
D1
1.0 MIN.
d
T
A0
B0
K0
1.5+0.10
-0.00
0.6+0.00
-0.40
4.0±0.10 4.0±0.10 2.0±0.05
3.20±0.20 3.10±0.20 1.50±0.20
A
H
50 MIN.
P1
T1
C
D
W
E1
F
12.4+2.00 13.0+0.50
-0.00 -0.20
178.0±
2.00
1.5 MIN. 20.2 MIN. 12.0±0.30 1.75±0.10 5.50±0.05
P0
P2
D0
D1
T
A0
B0
K0
1.5+0.10
-0.00
0.6+0.00
-0.40
4.0±0.10 8.0±0.10 2.0±0.05
1.5 MIN.
4.80±0.20 4.50±0.20 1.80±0.20
(mm)
Copyright ã ANPEC Electronics Corp.
14
www.anpec.com.tw
Rev. A.5 - Jul., 2013
APL5101/2
Devices Per Unit
Package Type
SOT-23-3
SOT-23-5
SOT-89
Unit
Quantity
3000
Tape & Reel
Tape & Reel
Tape & Reel
3000
1000
Taping Direction Information
SOT-23-3
USER DIRECTION OF FEED
SOT-23-5
USER DIRECTION OF FEED
SOT-89
USER DIRECTION OF FEED
Copyright ã ANPEC Electronics Corp.
15
www.anpec.com.tw
Rev. A.5 - Jul., 2013
APL5101/2
Classification Profile
Copyright ã ANPEC Electronics Corp.
16
www.anpec.com.tw
Rev. A.5 - Jul., 2013
APL5101/2
Classification Reflow Profiles
Profile Feature
Sn-Pb Eutectic Assembly
Pb-Free Assembly
Preheat & Soak
100 °C
150 °C
60-120 seconds
150 °C
200 °C
60-120 seconds
Temperature min (Tsmin
)
Temperature max (Tsmax
)
Time (Tsmin to Tsmax) (ts)
Average ramp-up rate
(Tsmax to TP)
3 °C/second max.
3°C/second max.
Liquidous temperature (TL)
Time at liquidous (tL)
183 °C
60-150 seconds
217 °C
60-150 seconds
Peak package body Temperature
(Tp)*
See Classification Temp in table 1
20** seconds
See Classification Temp in table 2
30** seconds
Time (tP)** within 5°C of the specified
classification temperature (Tc)
Average ramp-down rate (Tp to Tsmax
)
6 °C/second max.
6 °C/second max.
6 minutes max.
8 minutes max.
Time 25°C to peak temperature
* Tolerance for peak profile Temperature (Tp) is defined as a supplier minimum and a user maximum.
** Tolerance for time at peak profile temperature (tp) is defined as a supplier minimum and a user maximum.
Table 1. SnPb Eutectic Process – Classification Temperatures (Tc)
Volume mm3
350
Package
Thickness
<2.5 mm
Volume mm3
<350
235 °C
220 °C
³ 2.5 mm
220 °C
220 °C
Table 2. Pb-free Process – Classification Temperatures (Tc)
Package
Thickness
<1.6 mm
Volume mm3
Volume mm3
350-2000
260 °C
Volume mm3
<350
260 °C
260 °C
250 °C
>2000
260 °C
245 °C
245 °C
1.6 mm – 2.5 mm
³ 2.5 mm
250 °C
245 °C
Reliability Test Program
Test item
SOLDERABILITY
HOLT
Method
JESD-22, B102
JESD-22, A108
JESD-22, A102
JESD-22, A104
MIL-STD-883-3015.7
JESD-22, A115
JESD 78
Description
5 Sec, 245°C
1000 Hrs, Bias @ Tj=125°C
168 Hrs, 100%RH, 2atm, 121°C
500 Cycles, -65°C~150°C
VHBM≧2KV
PCT
TCT
HBM
MM
VMM≧200V
10ms, 1tr≧100mA
Latch-Up
Copyright ã ANPEC Electronics Corp.
17
www.anpec.com.tw
Rev. A.5 - Jul., 2013
APL5101/2
Customer Service
Anpec Electronics Corp.
Head Office :
No.6, Dusing 1st Road, SBIP,
Hsin-Chu, Taiwan
Tel : 886-3-5642000
Fax : 886-3-5642050
Taipei Branch :
2F, No. 11, Lane 218, Sec 2 Jhongsing Rd.,
Sindian City, Taipei County 23146, Taiwan
Tel : 886-2-2910-3838
Fax : 886-2-2917-3838
Copyright ã ANPEC Electronics Corp.
Rev. A.5 - Jul., 2013
18
www.anpec.com.tw
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明