AFE2000 [ARTESYN]

Single output; 单路输出


型号：	AFE2000
厂家：	ARTESYN TECHNOLOGIES
描述：	Single output 单路输出
文件：	总3页 (文件大小：141K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

AFE2000 SERIES

Single output

• Approved to EN61000, IEC-1000, UL1950,

CSA 22.2 No. 950-95

• Operating ambient temperature of 0°C to +50°C

• Complies with ETS300 132-1 and EN61000-3-2

• Hot-swap capability

• 11.5 x 6.75 x 4.9 inch size

• N+1 redundancy capability

• Extensive features available

• Compatible with AFS standard shelves for configuring

rack-mounted power systems

The AFE2000 power module is a rack mountable single phase AC to DC power

supply, designed to be a cost-competitive front-end power supply for distributed

power systems. It is particularly suitable for use in data processing, datacom and

telecom applications. The outputs are floating so the end user can ground the plus,

minus or neither depending on the end use application. The AFE2000 power modules

are designed for hot-swap operation and can be mounted into AFS4000/6000 power

shelves for redundant-mode operation.

[ 2 YEAR WARRANTY ]

SPECIFICATION ^{All specifications are typical at nominal input, full load at 25°C unless otherwise stated}

EMC CHARACTERISTICS

OUTPUT SPECIFICATIONS

Conducted emissions

FCC-CFR, part ±5, subpart B Class B

CISPR 22 Class B

Output voltage

Main: 48/54.5/56.2VDC

Auxiliary: ±2VDC

±±.0ꢀ

Radiated emissions

FCC-CFR, part ±5, subpart B (Note 7)

Output power

Main

Auxiliary

2000W

±2W

CISPR 22

(Note 7)

Immunity - conducted IEC±000-6

Level 2

Level ꢁ

Regulation

Turn-on

Line, load, IT, ageing

±ꢁ.0ꢀ

Immunity - radiated

Immunity - ESD

Line harmonics

IEC±000-ꢁ

IEC±000-2

per EN6±000-ꢁ-2

Level ꢁ

Output rise time

Turn-on (AC applied)

Turn-on (inhibit removed)

±00 to 400ms

4s max.

Compliant

±.5s max.

GENERAL SPECIFICATIONS

Ripple and noise

(<50MHz)

480mV pk-pk

Hold-up time

(See Note ±)

±50 to ±70VAC

0 to ±50VAC

500ms

20ms

Transmission noise

±00 to ꢁkHz

ꢁ5dBrnC

Efficiency

86ꢀ

Overvoltage protection

60VDC max.

Isolation voltage

Input/output

Input/chassis

Output/chassis

ꢁ000VAC

±500VAC

±00VAC

Undervoltage protection >44.5VDC

<42VDC for >5s

Delivers full power

Latch-off

Switching frequency

200kHz

Short circuit protection <ꢁ0s

>ꢁ0s

Automatic recovery

Latch-off

Approvals and

standards

EN60950, IEC950, UL±950

CSA C22.2 No. 950

Current sharing

Active current share

(50ꢀ to ±00ꢀ loading)

±±0ꢀ

Case material

Electrolytic zinc coated CRS,

ASTM A59±, light beige paint

Remote sense

±.0V max. distribution line loss

Weight

MTBF

5.0kg (±±Ibs)

INPUT SPECIFICATIONS

Input voltage range

MIL-HDBK-2±7E

Demonstrated

±50,000 hours

ꢁ00,000 hours

200/240VAC nom.

±70 to 264VAC

47Hz to 6ꢁHz

22A

Input frequency range 50/60Hz nom.

ENVIRONMENTAL SPECIFICATIONS

Input surge current

25°C cold start

254VAC @ 60Hz

Thermal performance

Operating ambient

Non-operating

0°C to +50°C

-40°C to +±00°C

Safety ground

leakage current

±.5mA max.

0.5mA typ.

Cooling

Forced air

5ꢀ to 95ꢀ RH

Input current

Power factor

220VAC, 2000W

±0.5A rms

0.99 min.

Relative humidity

Altitude

Operating

±ꢁ,000 feet max.

0.75G rms peak

Vibration

Shock

5Hz to 500Hz

±5G, ±/2 Sine, ±±ms

PAGE 1

DISTRIBUTED POWER FRONT END AC/DC POWER SUPPLIES

2000W AC/DC

2000 Watt

AC/DC PFC front-end for distributed power architectures

OUTPUT CURRENT

OUTPUT

VOLTAGE

TOTAL

REMOTE

PARALLEL

RIPPLE

MODEL NUMBER

MIN

MAX

4±.7A

ꢁ6.7A

ꢁ5.6A

REGULATION

ENABLE/INHIBIT

INTERFACES

48VDC

54.5VDC

56.2VDC

480mV

545mV

562mV

±ꢁ.0ꢀ

Inhibit

All

AFE2000-26S48NA

AFE2000-26S54NA

AFE2000-26S56NA

Reset

(RESET)

Parallel interface specifications.

Input bi-level signal. Bi-level input signal shall be no greater than 5VDC.

Logic 0 : Resets fault indicators without unit shut-down.

Logic ± : Normal operation.

All signals are referenced to ISO_GND unless otherwise indicated.

Isolated signal ground

(ISO_GND)

AC Good

(AC OK)

May be connected to any voltage in the range from +Vout+5VDC to -Vout-

5VDC.

Output bi-level signal. Bi-level output signal is open-collector (drain) with a

5mA sink capability and maximum voltage stand-off of 60VDC.

Logic 0 : AC input below normal operating range.

Overtemperature

(OTW)

Logic ± : AC input within steady-state operating range (±70 to 264VAC).

Output bi-level signal. Bi-level signals are open-collector (drain) with a 5mA

sink capability and maximum voltage stand-off of 60VDC.

Logic 0 : Signal precedes OT shutdown by 5ms.

Logic ± : Normal operation.

Voltage monitoring

Input analog signal referenced to RS-. Adjusts output up to 4VDC higher than

the nominal set point.

(VMARG)

Remote Inhibit

(INHIBIT)

Input bi-level signals. Bi-level input signals shall be no greater than 5VDC.

Logic 0 : Normal operation.

Logic ± : Output inhibit.

Features

Voltage margin down

(DOWN)

Input bi-level signals. Bi-level input signals shall be no greater than 5VDC.

Logic 0 : Nominal output voltage.

Live insertion and removal

OR-ing diodes provided on output.

Logic ± : 44.5 to 45.5VDC output.

Voltage monitoring jacks

Power good signal

(PWR_GOOD)

Located on front panel.

Output bi-level signal. Bi-level signals are open-collector (drain) with a 5mA

sink capability and maximum voltage stand-off of 60VDC.

Logic 0 : Output undervoltage.

LED’s (located on front panel)

Power Good

Power Fail

AC Good

Green

Red

Green

Logic ± : Output voltage normal.

Fault fail signal

(F/F ±)

Differential relay contact, isolated from all outputs and returns within the

power module.

Protection

Thermal protection - automatic shut-off for fan failure or internal

overtemperature.

Relay closed : Power supply failure

Relay open : Normal operation.

Output Overload and Short Circuit - automatic shut-down after ꢁ0 seconds.

Current regulated output down to less than ±VDC.

Power fail warning signal

(PFW)

Output bi-level signal. Bi-level signals are open-collector (drain) with a 5mA

sink capability and maximum voltage stand-off of 60VDC.

Logic 0 : Signal precedes loss of output power by 5ms.

Logic ± : Normal operation.

Output Overvoltage - automatic shut-down for both main (60VDC max.) and

auxiliary (±5.6VDC max.) outputs.

Output Undervoltage - automatic shut-down below 42VDC.

Module Missing Pin

(MM)

Provision for detection of unseated or removed module. MM pins are

common internal to the power supply. Internal pull-up resistor to +5VDC logic

bias, referenced to RS-.

Current Share

Active current sharing for up to 9 AFE2000 power modules.

Short Pin

Auxiliary Output

(AUX ±)

Short pin located in the output connector initiates shut-down of the power

supply output when the power supply is removed from the host power shelf.

±2VDC auxiliary output. Isolated from both the main output and the isolated

signal ground. May be utilized for external housekeeping supply and

connected to either main output or isolated signal ground.

Current Monitor

(IMON)

Current source which mirrors magnitude of the output current. Signal return

is referenced to RS-.

Current Limit

(CL)

Output bi-level signal. Bi-level output signal is open-collector (drain) with a

5mA sink capability and maximum voltage stand-off of 60VDC.

Logic 0 : Output is in current mode control and is current limiting.

Logic ± : Normal operation.

Remote Enable

(ENABLE)

Input bi-level signal. Bi-level input signal shall be no greater than 5VDC.

Logic 0 : Output inhibited.

Logic ± : Normal operation.

International Safety Standard Approvals

EN60950/IEC950 File No. E9972ꢁ97

UL±950 File No. E±ꢁ57ꢁ4

Please consult our website for the following items: ✔ Application Note

http://www.artesyn.com

PAGE 2

2000W AC/DC

DISTRIBUTED POWER FRONT END AC/DC POWER SUPPLIES

2000 Watt

AC/DC PFC front-end for distributed power architectures

PIN CONNECTIONS

PIN NO.

A±

FUNCTION

Short Pin

AUX+

PIN NO.

B±

FUNCTION

DOWN

PIN NO.

C±

FUNCTION

PIN NO.

D±

FUNCTION

+Vout

RS+

VMARG

RS-

+Vout

Aꢁ

AUX-

Bꢁ

Cꢁ

Dꢁ

PWR RTN

CGND ⁽²⁾

RS-

I SHR

F/F-

F/F+

Not Used

AC OK

PFW

RESET

IMON

INHIBIT/ENABLE

Power Good

ISO GND ^(ꢁ)

OTW

Notes

Class A for power module, Class B when installed in AFS4000 shelf

(subject to cable/system configuration).

NOTICE: Some models do not support all options. Please contact your

local Artesyn representative or use the on-line model number search tool at

http://www.artesyn.com/powergroup/products.htm to find a suitable

alternative.

ꢁ

PFW signal warning issued 5 msec prior to shutdown.

Chassis or safety ground.

Isolated signal ground.

Output ground - referenced to RS-.

Refer to Application Note ±06 for installation of the AFE2000 power

modules into the AFS4000 power shelf.

Refer to Application Note ±±0 for description of outputs and signals

available with AFE2000 power modules installed in Artesyn standard front-

end power shelf.

SHORT SIGNAL PIN

A±

B±

C±

Dꢁ

D±

6.44

(±6ꢁ.58)

AIR FLOW

NORMAL

AC INPUT

POWER DYNAMICS 42R08-±±22

MATE - POWER DYNAMICS 4ꢁR06-2±±4

(6.ꢁ5)

0.074

(±.879)

±±.46

(29±.08)

0.25

6.75

(±7±.45)

±.ꢁ0

(ꢁꢁ.02)

0.050

(±.270)

5.725

(±45.4±5)

TAPERED GUIDE

PIN HOLE

0.800

(20.ꢁ2)

4.2ꢁ

(±07.44)

4.8ꢁ

(±22.68)

0.0875

(2.2225)

2.06ꢁ

(52.400)

0.625

(±5.875)

REF

0.ꢁ75

(9.525)

0.462

(±±.7ꢁ5)

0.475

(±2.065)

MAIN DC OUTPUT/SIGNALS

TAPERED GUIDE

PIN HOLE

ELCON 279-0468-00±00

MATE - ELCON 278-0468-00200

INSERTION/EJECTOR

HANDLE WITH 6-ꢁ2

CAPTIVE SCREW

(J2) DC connector

(J2) DC mating connector

Elcon 279-0468-00±00 or equivalent.

Elcon 278-0468-00200 or equivalent.

(J1) AC connector

(J1) AC mating connector

Power Dynamics 42R08-±±22 or equivalent.

Power Dynamics 4ꢁR06-2±±4 or equivalent.

® 2005

The information and specifications contained in this datasheet are believed to be correct at time of publication. However, Artesyn Technologies accepts no responsibility for consequences arising

from printing errors or inaccuracies. Specifications are subject to change without notice. No rights under any patent accompany the sale of any such product(s) or information contained herein.

PAGE 3

AFE2000 [ARTESYN]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB

SI9137LG

SI9122E