ATMEGA88PA-AUR
更新时间:2024-09-18 08:13:56
品牌:ATMEL
描述:8-bit Microcontroller with 4/8/16/32K Bytes In-System Programmable Flash
ATMEGA88PA-AUR 概述
8-bit Microcontroller with 4/8/16/32K Bytes In-System Programmable Flash 8位微控制器与4/8/ 16 / 32K字节的系统内可编程闪存 8位微控制器 微控制器
ATMEGA88PA-AUR 规格参数
是否Rohs认证: | 符合 | 生命周期: | Transferred |
零件包装代码: | QFP | 包装说明: | TQFP, TQFP32,.35SQ,32 |
针数: | 32 | Reach Compliance Code: | unknown |
ECCN代码: | EAR99 | HTS代码: | 8542.31.00.01 |
Factory Lead Time: | 1 week | 风险等级: | 5.21 |
核心架构: | AVR | 设备核心: | AVR |
时钟速度: | 20 | 内存: | 1 |
闪存: | 8 | 能够: | 0 |
Adc通道: | 8 | ADC分辨率: | 10 |
Samacsys Confidence: | 3 | Samacsys Status: | Released |
Samacsys PartID: | 235662 | Samacsys Pin Count: | 32 |
Samacsys Part Category: | Integrated Circuit | Samacsys Package Category: | Quad Flat Packages |
Samacsys Footprint Name: | ATMEGA88PA-AUR | Samacsys Released Date: | 2019-04-14 06:18:10 |
Is Samacsys: | N | 具有ADC: | YES |
其他特性: | ALSO OPERATES AT 2.7 V MINIMUM SUPPLY AT 10 MHZ AND 1.8 V MINIMUM SUPPLY AT 4 MHZ | 地址总线宽度: | |
位大小: | 8 | CPU系列: | AVR RISC |
最大时钟频率: | 20 MHz | DAC 通道: | NO |
DMA 通道: | NO | 外部数据总线宽度: | |
JESD-30 代码: | S-PQFP-G32 | JESD-609代码: | e3 |
长度: | 7 mm | 湿度敏感等级: | 3 |
I/O 线路数量: | 23 | 端子数量: | 32 |
片上程序ROM宽度: | 16 | 最高工作温度: | 85 °C |
最低工作温度: | -40 °C | PWM 通道: | YES |
封装主体材料: | PLASTIC/EPOXY | 封装代码: | TQFP |
封装等效代码: | TQFP32,.35SQ,32 | 封装形状: | SQUARE |
封装形式: | FLATPACK, THIN PROFILE | 峰值回流温度(摄氏度): | 260 |
电源: | 2/5 V | 认证状态: | Not Qualified |
RAM(字节): | 1024 | ROM(单词): | 4096 |
ROM可编程性: | FLASH | 座面最大高度: | 1.2 mm |
速度: | 20 MHz | 子类别: | Microcontrollers |
最大压摆率: | 9 mA | 最大供电电压: | 5.5 V |
最小供电电压: | 4.5 V | 标称供电电压: | 5 V |
表面贴装: | YES | 技术: | CMOS |
温度等级: | INDUSTRIAL | 端子面层: | Matte Tin (Sn) |
端子形式: | GULL WING | 端子节距: | 0.8 mm |
端子位置: | QUAD | 处于峰值回流温度下的最长时间: | NOT SPECIFIED |
宽度: | 7 mm | uPs/uCs/外围集成电路类型: | MICROCONTROLLER, RISC |
Base Number Matches: | 1 |
ATMEGA88PA-AUR 数据手册
通过下载ATMEGA88PA-AUR数据手册来全面了解它。这个PDF文档包含了所有必要的细节,如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载Features
• High Performance, Low Power AVR® 8-Bit Microcontroller
• Advanced RISC Architecture
– 131 Powerful Instructions – Most Single Clock Cycle Execution
– 32 x 8 General Purpose Working Registers
– Fully Static Operation
– Up to 20 MIPS Throughput at 20 MHz
– On-chip 2-cycle Multiplier
• High Endurance Non-volatile Memory Segments
– 4/8/16/32K Bytes of In-System Self-Programmable Flash program memory
– 256/512/512/1K Bytes EEPROM
8-bit
– 512/1K/1K/2K Bytes Internal SRAM
– Write/Erase Cycles: 10,000 Flash/100,000 EEPROM
– Data retention: 20 years at 85°C/100 years at 25°C(1)
– Optional Boot Code Section with Independent Lock Bits
In-System Programming by On-chip Boot Program
True Read-While-Write Operation
Microcontroller
with 4/8/16/32K
Bytes In-System
Programmable
Flash
– Programming Lock for Software Security
• Peripheral Features
– Two 8-bit Timer/Counters with Separate Prescaler and Compare Mode
– One 16-bit Timer/Counter with Separate Prescaler, Compare Mode, and Capture
Mode
– Real Time Counter with Separate Oscillator
– Six PWM Channels
– 8-channel 10-bit ADC in TQFP and QFN/MLF package
Temperature Measurement
– 6-channel 10-bit ADC in PDIP Package
Temperature Measurement
ATmega48A
ATmega48PA
ATmega88A
ATmega88PA
ATmega168A
ATmega168PA
ATmega328
– Programmable Serial USART
– Master/Slave SPI Serial Interface
– Byte-oriented 2-wire Serial Interface (Philips I2C compatible)
– Programmable Watchdog Timer with Separate On-chip Oscillator
– On-chip Analog Comparator
– Interrupt and Wake-up on Pin Change
• Special Microcontroller Features
– Power-on Reset and Programmable Brown-out Detection
– Internal Calibrated Oscillator
– External and Internal Interrupt Sources
– Six Sleep Modes: Idle, ADC Noise Reduction, Power-save, Power-down, Standby,
and Extended Standby
• I/O and Packages
ATmega328P
– 23 Programmable I/O Lines
– 28-pin PDIP, 32-lead TQFP, 28-pad QFN/MLF and 32-pad QFN/MLF
• Operating Voltage:
– 1.8 - 5.5V
• Temperature Range:
– -40°C to 85°C
• Speed Grade:
Summary
– 0 - 4 MHz@1.8 - 5.5V, 0 - 10 MHz@2.7 - 5.5.V, 0 - 20 MHz @ 4.5 - 5.5V
• Power Consumption at 1 MHz, 1.8V, 25°C
– Active Mode: 0.2 mA
– Power-down Mode: 0.1 µA
– Power-save Mode: 0.75 µA (Including 32 kHz RTC)
Rev. 8271BS–AVR–04/10
ATmega48A/48PA/88A/88PA/168A/168PA/328/328P
1. Pin Configurations
Figure 1-1. Pinout ATmega48A/48PA/88A/88PA/168A/168PA/328/328P
PDIP
TQFP Top View
(PCINT14/RESET) PC6
(PCINT16/RXD) PD0
(PCINT17/TXD) PD1
(PCINT18/INT0) PD2
(PCINT19/OC2B/INT1) PD3
(PCINT20/XCK/T0) PD4
VCC
1
2
3
4
5
6
7
8
9
28 PC5 (ADC5/SCL/PCINT13)
27 PC4 (ADC4/SDA/PCINT12)
26 PC3 (ADC3/PCINT11)
25 PC2 (ADC2/PCINT10)
24 PC1 (ADC1/PCINT9)
23 PC0 (ADC0/PCINT8)
22 GND
(PCINT19/OC2B/INT1) PD3
1
2
3
4
5
6
7
8
24 PC1 (ADC1/PCINT9)
23 PC0 (ADC0/PCINT8)
22 ADC7
(PCINT20/XCK/T0) PD4
GND
VCC
GND
21 GND
20 AREF
GND
21 AREF
VCC
19 ADC6
(PCINT6/XTAL1/TOSC1) PB6
20 AVCC
(PCINT6/XTAL1/TOSC1) PB6
(PCINT7/XTAL2/TOSC2) PB7
18 AVCC
(PCINT7/XTAL2/TOSC2) PB7 10
(PCINT21/OC0B/T1) PD5 11
(PCINT22/OC0A/AIN0) PD6 12
(PCINT23/AIN1) PD7 13
19 PB5 (SCK/PCINT5)
18 PB4 (MISO/PCINT4)
17 PB3 (MOSI/OC2A/PCINT3)
16 PB2 (SS/OC1B/PCINT2)
15 PB1 (OC1A/PCINT1)
17 PB5 (SCK/PCINT5)
(PCINT0/CLKO/ICP1) PB0 14
32 MLF Top View
28 MLF Top View
(PCINT19/OC2B/INT1) PD3
PC1 (ADC1/PCINT9)
PC0 (ADC0/PCINT8)
ADC7
1
2
3
4
5
6
7
8
24
23
22
21
20
19
18
17
(PCINT19/OC2B/INT1) PD3
(PCINT20/XCK/T0) PD4
VCC
PC2 (ADC2/PCINT10)
PC1 (ADC1/PCINT9)
PC0 (ADC0/PCINT8)
GND
1
2
3
4
5
6
7
21
20
19
18
17
16
15
(PCINT20/XCK/T0) PD4
GND
VCC
GND
GND
GND
AREF
(PCINT6/XTAL1/TOSC1) PB6
(PCINT7/XTAL2/TOSC2) PB7
(PCINT21/OC0B/T1) PD5
AREF
VCC
ADC6
AVCC
(PCINT6/XTAL1/TOSC1) PB6
(PCINT7/XTAL2/TOSC2) PB7
AVCC
PB5 (SCK/PCINT5)
PB5 (SCK/PCINT5)
NOTE: Bottom pad should be soldered to ground.
NOTE: Bottom pad should be soldered to ground.
2
8271BS–AVR–04/10
ATmega48A/48PA/88A/88PA/168A/168PA/328/328P
1.1
Pin Descriptions
1.1.1
VCC
Digital supply voltage.
1.1.2
1.1.3
GND
Ground.
Port B (PB7:0) XTAL1/XTAL2/TOSC1/TOSC2
Port B is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The
Port B output buffers have symmetrical drive characteristics with both high sink and source
capability. As inputs, Port B pins that are externally pulled low will source current if the pull-up
resistors are activated. The Port B pins are tri-stated when a reset condition becomes active,
even if the clock is not running.
Depending on the clock selection fuse settings, PB6 can be used as input to the inverting Oscil-
lator amplifier and input to the internal clock operating circuit.
Depending on the clock selection fuse settings, PB7 can be used as output from the inverting
Oscillator amplifier.
If the Internal Calibrated RC Oscillator is used as chip clock source, PB7...6 is used as
TOSC2...1 input for the Asynchronous Timer/Counter2 if the AS2 bit in ASSR is set.
The various special features of Port B are elaborated in and ”System Clock and Clock Options”
on page 26.
1.1.4
1.1.5
Port C (PC5:0)
PC6/RESET
Port C is a 7-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The
PC5...0 output buffers have symmetrical drive characteristics with both high sink and source
capability. As inputs, Port C pins that are externally pulled low will source current if the pull-up
resistors are activated. The Port C pins are tri-stated when a reset condition becomes active,
even if the clock is not running.
If the RSTDISBL Fuse is programmed, PC6 is used as an I/O pin. Note that the electrical char-
acteristics of PC6 differ from those of the other pins of Port C.
If the RSTDISBL Fuse is unprogrammed, PC6 is used as a Reset input. A low level on this pin
for longer than the minimum pulse length will generate a Reset, even if the clock is not running.
The minimum pulse length is given in Table 28-12 on page 323. Shorter pulses are not guaran-
teed to generate a Reset.
The various special features of Port C are elaborated in ”Alternate Functions of Port C” on page
86.
1.1.6
Port D (PD7:0)
Port D is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The
Port D output buffers have symmetrical drive characteristics with both high sink and source
capability. As inputs, Port D pins that are externally pulled low will source current if the pull-up
resistors are activated. The Port D pins are tri-stated when a reset condition becomes active,
even if the clock is not running.
3
8271BS–AVR–04/10
ATmega48A/48PA/88A/88PA/168A/168PA/328/328P
The various special features of Port D are elaborated in ”Alternate Functions of Port D” on page
89.
1.1.7
AVCC
AVCC is the supply voltage pin for the A/D Converter, PC3:0, and ADC7:6. It should be externally
connected to VCC, even if the ADC is not used. If the ADC is used, it should be connected to VCC
through a low-pass filter. Note that PC6...4 use digital supply voltage, VCC
.
1.1.8
1.1.9
AREF
AREF is the analog reference pin for the A/D Converter.
ADC7:6 (TQFP and QFN/MLF Package Only)
In the TQFP and QFN/MLF package, ADC7:6 serve as analog inputs to the A/D converter.
These pins are powered from the analog supply and serve as 10-bit ADC channels.
4
8271BS–AVR–04/10
ATmega48A/48PA/88A/88PA/168A/168PA/328/328P
2. Overview
The ATmega48A/48PA/88A/88PA/168A/168PA/328/328P is a low-power CMOS 8-bit microcon-
troller based on the AVR enhanced RISC architecture. By executing powerful instructions in a
single clock cycle, the ATmega48A/48PA/88A/88PA/168A/168PA/328/328P achieves through-
puts approaching 1 MIPS per MHz allowing the system designer to optimize power consumption
versus processing speed.
2.1
Block Diagram
Figure 2-1. Block Diagram
Watchdog
Timer
Power
Supervision
POR / BOD &
RESET
debugWIRE
Watchdog
Oscillator
PROGRAM
LOGIC
Oscillator
Circuits /
Clock
Flash
SRAM
Generation
CPU
EEPROM
AVCC
AREF
GND
2
8bit T/C 0
8bit T/C 2
16bit T/C 1
A/D Conv.
Analog
Comp.
Internal
Bandgap
6
USART 0
PORT D (8)
PD[0..7]
SPI
PORT B (8)
PB[0..7]
TWI
PORT C (7)
PC[0..6]
RESET
XTAL[1..2]
ADC[6..7]
The AVR core combines a rich instruction set with 32 general purpose working registers. All the
32 registers are directly connected to the Arithmetic Logic Unit (ALU), allowing two independent
5
8271BS–AVR–04/10
ATmega48A/48PA/88A/88PA/168A/168PA/328/328P
registers to be accessed in one single instruction executed in one clock cycle. The resulting
architecture is more code efficient while achieving throughputs up to ten times faster than con-
ventional CISC microcontrollers.
The ATmega48A/48PA/88A/88PA/168A/168PA/328/328P provides the following features:
4K/8K bytes of In-System Programmable Flash with Read-While-Write capabilities,
256/512/512/1K bytes EEPROM, 512/1K/1K/2K bytes SRAM, 23 general purpose I/O lines, 32
general purpose working registers, three flexible Timer/Counters with compare modes, internal
and external interrupts, a serial programmable USART, a byte-oriented 2-wire Serial Interface,
an SPI serial port, a 6-channel 10-bit ADC (8 channels in TQFP and QFN/MLF packages), a pro-
grammable Watchdog Timer with internal Oscillator, and five software selectable power saving
modes. The Idle mode stops the CPU while allowing the SRAM, Timer/Counters, USART, 2-wire
Serial Interface, SPI port, and interrupt system to continue functioning. The Power-down mode
saves the register contents but freezes the Oscillator, disabling all other chip functions until the
next interrupt or hardware reset. In Power-save mode, the asynchronous timer continues to run,
allowing the user to maintain a timer base while the rest of the device is sleeping. The ADC
Noise Reduction mode stops the CPU and all I/O modules except asynchronous timer and ADC,
to minimize switching noise during ADC conversions. In Standby mode, the crystal/resonator
Oscillator is running while the rest of the device is sleeping. This allows very fast start-up com-
bined with low power consumption.
The device is manufactured using Atmel’s high density non-volatile memory technology. The
On-chip ISP Flash allows the program memory to be reprogrammed In-System through an SPI
serial interface, by a conventional non-volatile memory programmer, or by an On-chip Boot pro-
gram running on the AVR core. The Boot program can use any interface to download the
application program in the Application Flash memory. Software in the Boot Flash section will
continue to run while the Application Flash section is updated, providing true Read-While-Write
operation. By combining an 8-bit RISC CPU with In-System Self-Programmable Flash on a
monolithic chip, the Atmel ATmega48A/48PA/88A/88PA/168A/168PA/328/328P is a powerful
microcontroller that provides a highly flexible and cost effective solution to many embedded con-
trol applications.
The ATmega48A/48PA/88A/88PA/168A/168PA/328/328P AVR is supported with a full suite of
program and system development tools including: C Compilers, Macro Assemblers, Program
Debugger/Simulators, In-Circuit Emulators, and Evaluation kits.
2.2
Comparison Between Processors
The ATmega48A/48PA/88A/88PA/168A/168PA/328/328P differ only in memory sizes, boot
loader support, and interrupt vector sizes. Table 2-1 summarizes the different memory and inter-
rupt vector sizes for the devices.
Table 2-1.
Device
Memory Size Summary
Flash
EEPROM
RAM
Interrupt Vector Size
ATmega48A
ATmega48PA
ATmega88A
ATmega88PA
ATmega168A
4K Bytes
4K Bytes
8K Bytes
8K Bytes
16K Bytes
256 Bytes
256 Bytes
512 Bytes
512 Bytes
512 Bytes
512 Bytes
512 Bytes
1K Bytes
1K Bytes
1K Bytes
1 instruction word/vector
1 instruction word/vector
1 instruction word/vector
1 instruction word/vector
2 instruction words/vector
6
8271BS–AVR–04/10
ATmega48A/48PA/88A/88PA/168A/168PA/328/328P
Table 2-1.
Memory Size Summary
Device
Flash
EEPROM
RAM
Interrupt Vector Size
ATmega168PA
ATmega328
ATmega328P
16K Bytes
32K Bytes
32K Bytes
512 Bytes
1K Bytes
1K Bytes
1K Bytes
2K Bytes
2K Bytes
2 instruction words/vector
2 instruction words/vector
2 instruction words/vector
ATmega48A/48PA/88A/88PA/168A/168PA/328/328P support a real Read-While-Write Self-Pro-
gramming mechanism. There is a separate Boot Loader Section, and the SPM instruction can
only execute from there. In ATmega 48A/48PA there is no Read-While-Write support and no
separate Boot Loader Section. The SPM instruction can execute from the entire Flash.
3. Resources
A comprehensive set of development tools, application notes and datasheets are available for
download on http://www.atmel.com/avr.
Note:
1.
7
8271BS–AVR–04/10
ATmega48A/48PA/88A/88PA/168A/168PA/328/328P
4. Register Summary
Address
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Page
(0xFF)
(0xFE)
(0xFD)
(0xFC)
(0xFB)
(0xFA)
(0xF9)
(0xF8)
(0xF7)
(0xF6)
(0xF5)
(0xF4)
(0xF3)
(0xF2)
(0xF1)
(0xF0)
(0xEF)
(0xEE)
(0xED)
(0xEC)
(0xEB)
(0xEA)
(0xE9)
(0xE8)
(0xE7)
(0xE6)
(0xE5)
(0xE4)
(0xE3)
(0xE2)
(0xE1)
(0xE0)
(0xDF)
(0xDE)
(0xDD)
(0xDC)
(0xDB)
(0xDA)
(0xD9)
(0xD8)
(0xD7)
(0xD6)
(0xD5)
(0xD4)
(0xD3)
(0xD2)
(0xD1)
(0xD0)
(0xCF)
(0xCE)
(0xCD)
(0xCC)
(0xCB)
(0xCA)
(0xC9)
(0xC8)
(0xC7)
(0xC6)
(0xC5)
(0xC4)
(0xC3)
(0xC2)
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
UDR0
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
USART I/O Data Register
196
200
200
UBRR0H
UBRR0L
Reserved
UCSR0C
USART Baud Rate Register High
USART Baud Rate Register Low
–
–
–
–
–
–
–
–
UCSZ01 /UDORD0
UCSZ00 / UCPHA0
UMSEL01
UMSEL00
UPM01
UPM00
USBS0
UCPOL0
198/213
8
8271BS–AVR–04/10
ATmega48A/48PA/88A/88PA/168A/168PA/328/328P
Address
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Page
(0xC1)
(0xC0)
(0xBF)
(0xBE)
(0xBD)
(0xBC)
(0xBB)
(0xBA)
(0xB9)
(0xB8)
(0xB7)
(0xB6)
(0xB5)
(0xB4)
(0xB3)
(0xB2)
(0xB1)
(0xB0)
(0xAF)
(0xAE)
(0xAD)
(0xAC)
(0xAB)
(0xAA)
(0xA9)
(0xA8)
(0xA7)
(0xA6)
(0xA5)
(0xA4)
(0xA3)
(0xA2)
(0xA1)
(0xA0)
(0x9F)
(0x9E)
(0x9D)
(0x9C)
(0x9B)
(0x9A)
(0x99)
(0x98)
(0x97)
(0x96)
(0x95)
(0x94)
(0x93)
(0x92)
(0x91)
(0x90)
(0x8F)
(0x8E)
(0x8D)
(0x8C)
(0x8B)
(0x8A)
(0x89)
(0x88)
(0x87)
(0x86)
(0x85)
(0x84)
(0x83)
(0x82)
(0x81)
(0x80)
UCSR0B
UCSR0A
Reserved
Reserved
TWAMR
TWCR
RXCIE0
RXC0
–
TXCIE0
TXC0
–
UDRIE0
UDRE0
–
RXEN0
FE0
TXEN0
DOR0
–
UCSZ02
UPE0
–
RXB80
TXB80
197
196
U2X0
MPCM0
–
–
–
–
–
–
–
–
–
–
–
TWAM0
–
TWAM6
TWINT
TWAM5
TWEA
TWAM4
TWSTA
TWAM3
TWSTO
TWAM2
TWWC
TWAM1
TWEN
–
245
242
244
245
244
242
TWIE
TWDR
2-wire Serial Interface Data Register
TWAR
TWA6
TWS7
TWA5
TWS6
TWA4
TWS5
TWA3
TWS4
TWA2
TWS3
TWA1
–
TWA0
TWGCE
TWPS0
TWSR
TWPS1
TWBR
2-wire Serial Interface Bit Rate Register
Reserved
ASSR
–
–
–
–
AS2
–
–
TCN2UB
–
–
OCR2AUB
–
–
OCR2BUB
–
–
TCR2AUB
–
–
TCR2BUB
–
EXCLK
–
165
Reserved
OCR2B
Timer/Counter2 Output Compare Register B
Timer/Counter2 Output Compare Register A
Timer/Counter2 (8-bit)
163
163
163
162
OCR2A
TCNT2
TCCR2B
TCCR2A
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
OCR1BH
OCR1BL
OCR1AH
OCR1AL
ICR1H
FOC2A
FOC2B
–
–
WGM22
CS22
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
CS21
CS20
COM2A1
COM2A0
COM2B1
COM2B0
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
WGM21
WGM20
159
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Timer/Counter1 - Output Compare Register B High Byte
Timer/Counter1 - Output Compare Register B Low Byte
Timer/Counter1 - Output Compare Register A High Byte
Timer/Counter1 - Output Compare Register A Low Byte
Timer/Counter1 - Input Capture Register High Byte
Timer/Counter1 - Input Capture Register Low Byte
Timer/Counter1 - Counter Register High Byte
139
139
139
139
139
139
139
139
ICR1L
TCNT1H
TCNT1L
Reserved
TCCR1C
TCCR1B
TCCR1A
Timer/Counter1 - Counter Register Low Byte
–
–
–
–
–
–
–
–
–
–
–
FOC1A
ICNC1
COM1A1
FOC1B
ICES1
COM1A0
–
–
–
–
WGM12
–
138
137
135
WGM13
COM1B0
CS12
–
CS11
WGM11
CS10
WGM10
COM1B1
9
8271BS–AVR–04/10
ATmega48A/48PA/88A/88PA/168A/168PA/328/328P
Address
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Page
(0x7F)
(0x7E)
DIDR1
DIDR0
–
–
–
–
–
–
ADC3D
–
–
AIN1D
ADC1D
–
AIN0D
ADC0D
–
250
267
–
–
ADC5D
–
ADC4D
ADC2D
–
(0x7D)
Reserved
ADMUX
ADCSRB
ADCSRA
ADCH
–
–
–
(0x7C)
REFS1
–
REFS0
ACME
ADSC
ADLAR
–
MUX3
–
MUX2
ADTS2
ADPS2
MUX1
ADTS1
ADPS1
MUX0
ADTS0
ADPS0
263
266
264
266
266
(0x7B)
–
(0x7A)
ADEN
ADATE
ADIF
ADIE
(0x79)
ADC Data Register High byte
ADC Data Register Low byte
(0x78)
ADCL
(0x77)
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
TIMSK2
TIMSK1
TIMSK0
PCMSK2
PCMSK1
PCMSK0
Reserved
EICRA
–
–
–
–
–
–
–
–
(0x76)
–
–
–
–
–
–
–
–
(0x75)
–
–
–
–
–
–
–
–
–
–
–
(0x74)
–
–
–
–
–
(0x73)
–
–
–
–
–
–
–
–
(0x72)
–
–
–
–
–
–
–
–
(0x71)
–
–
–
–
–
–
–
–
(0x70)
–
–
–
–
–
OCIE2B
OCIE1B
OCIE0B
PCINT18
PCINT10
PCINT2
–
OCIE2A
OCIE1A
OCIE0A
PCINT17
PCINT9
PCINT1
–
TOIE2
TOIE1
TOIE0
PCINT16
PCINT8
PCINT0
–
164
140
112
75
(0x6F)
–
–
ICIE1
–
–
(0x6E)
–
–
–
–
–
PCINT19
PCINT11
PCINT3
–
(0x6D)
PCINT23
PCINT22
PCINT21
PCINT20
(0x6C)
–
PCINT14
PCINT13
PCINT12
75
(0x6B)
PCINT7
PCINT6
PCINT5
PCINT4
75
(0x6A)
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
(0x69)
ISC11
–
ISC10
PCIE2
–
ISC01
PCIE1
–
ISC00
PCIE0
–
72
(0x68)
PCICR
(0x67)
Reserved
OSCCAL
Reserved
PRR
–
(0x66)
Oscillator Calibration Register
37
42
(0x65)
–
–
–
–
–
–
–
–
(0x64)
PRTWI
PRTIM2
PRTIM0
–
PRTIM1
PRSPI
PRUSART0
PRADC
(0x63)
Reserved
Reserved
CLKPR
–
–
–
–
–
–
–
–
(0x62)
–
–
–
–
–
–
–
–
(0x61)
CLKPCE
–
–
–
CLKPS3
CLKPS2
CLKPS1
CLKPS0
37
55
9
(0x60)
WDTCSR
SREG
WDIF
WDIE
WDP3
WDCE
WDE
WDP2
WDP1
WDP0
0x3F (0x5F)
0x3E (0x5E)
0x3D (0x5D)
0x3C (0x5C)
0x3B (0x5B)
0x3A (0x5A)
0x39 (0x59)
0x38 (0x58)
0x37 (0x57)
0x36 (0x56)
0x35 (0x55)
0x34 (0x54)
0x33 (0x53)
0x32 (0x52)
0x31 (0x51)
0x30 (0x50)
0x2F (0x4F)
0x2E (0x4E)
0x2D (0x4D)
0x2C (0x4C)
0x2B (0x4B)
0x2A (0x4A)
0x29 (0x49)
0x28 (0x48)
0x27 (0x47)
0x26 (0x46)
0x25 (0x45)
0x24 (0x44)
0x23 (0x43)
0x22 (0x42)
0x21 (0x41)
0x20 (0x40)
0x1F (0x3F)
0x1E (0x3E)
I
T
H
S
V
N
Z
C
SPH
–
–
–
–
–
(SP10) 5.
SP9
SP8
12
12
SPL
SP7
SP6
SP5
SP4
SP3
SP2
SP1
SP0
Reserved
Reserved
Reserved
Reserved
Reserved
SPMCSR
Reserved
MCUCR
MCUSR
SMCR
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
PGERS
–
–
SPMIE
(RWWSB)5.
–
(RWWSRE)5.
BLBSET
PGWRT
SELFPRGEN
294
–
–
–
–
–
PUD
–
–
–
–
–
–
IVCE
PORF
SE
BODS(6)
BODSE(6)
IVSEL
EXTRF
SM0
–
45/69/93
55
–
–
–
–
WDRF
SM2
–
BORF
SM1
–
–
–
–
40
Reserved
Reserved
ACSR
–
–
–
–
–
–
–
ACBG
–
–
–
–
–
–
–
ACD
–
ACO
–
ACI
–
ACIE
–
ACIC
–
ACIS1
–
ACIS0
–
248
Reserved
SPDR
SPI Data Register
176
175
174
25
SPSR
SPIF
SPIE
WCOL
SPE
–
–
–
–
–
SPI2X
SPR0
SPCR
DORD
MSTR
CPOL
CPHA
SPR1
GPIOR2
GPIOR1
Reserved
OCR0B
OCR0A
TCNT0
General Purpose I/O Register 2
General Purpose I/O Register 1
25
–
–
–
–
–
–
–
–
Timer/Counter0 Output Compare Register B
Timer/Counter0 Output Compare Register A
Timer/Counter0 (8-bit)
TCCR0B
TCCR0A
GTCCR
EEARH
EEARL
FOC0A
COM0A1
TSM
FOC0B
COM0A0
–
–
COM0B1
–
–
COM0B0
–
WGM02
CS02
CS01
CS00
–
–
–
–
WGM01
PSRASY
WGM00
PSRSYNC
144/166
21
(EEPROM Address Register High Byte) 5.
EEPROM Address Register Low Byte
EEPROM Data Register
21
EEDR
21
EECR
–
–
EEPM1
EEPM0
EERIE
EEMPE
EEPE
EERE
21
GPIOR0
General Purpose I/O Register 0
25
10
8271BS–AVR–04/10
ATmega48A/48PA/88A/88PA/168A/168PA/328/328P
Address
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Page
0x1D (0x3D)
0x1C (0x3C)
0x1B (0x3B)
0x1A (0x3A)
0x19 (0x39)
0x18 (0x38)
0x17 (0x37)
0x16 (0x36)
0x15 (0x35)
0x14 (0x34)
0x13 (0x33)
0x12 (0x32)
0x11 (0x31)
0x10 (0x30)
0x0F (0x2F)
0x0E (0x2E)
0x0D (0x2D)
0x0C (0x2C)
0x0B (0x2B)
0x0A (0x2A)
0x09 (0x29)
0x08 (0x28)
0x07 (0x27)
0x06 (0x26)
0x05 (0x25)
0x04 (0x24)
0x03 (0x23)
0x02 (0x22)
0x01 (0x21)
0x0 (0x20)
EIMSK
EIFR
–
–
–
–
–
–
INT1
INT0
73
73
–
–
–
–
–
–
INTF1
INTF0
PCIFR
–
–
–
–
–
PCIF2
PCIF1
PCIF0
Reserved
Reserved
Reserved
TIFR2
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
OCF2B
OCF2A
TOV2
164
140
TIFR1
–
–
ICF1
–
–
OCF1B
OCF1A
TOV1
TIFR0
–
–
–
–
–
OCF0B
OCF0A
TOV0
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
PORTD
DDRD
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
PORTD7
PORTD6
DDD6
PIND6
PORTC6
DDC6
PINC6
PORTB6
DDB6
PINB6
–
PORTD5
DDD5
PIND5
PORTC5
DDC5
PINC5
PORTB5
DDB5
PINB5
–
PORTD4
DDD4
PIND4
PORTC4
DDC4
PINC4
PORTB4
DDB4
PINB4
–
PORTD3
DDD3
PIND3
PORTC3
DDC3
PINC3
PORTB3
DDB3
PINB3
–
PORTD2
DDD2
PIND2
PORTC2
DDC2
PINC2
PORTB2
DDB2
PINB2
–
PORTD1
DDD1
PIND1
PORTC1
DDC1
PINC1
PORTB1
DDB1
PINB1
–
PORTD0
DDD0
PIND0
PORTC0
DDC0
PINC0
PORTB0
DDB0
PINB0
–
94
94
94
93
93
93
93
93
93
DDD7
PIND
PIND7
PORTC
DDRC
–
–
PINC
–
PORTB
DDRB
PORTB7
DDB7
PINB
PINB7
Reserved
Reserved
Reserved
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Note:
1. For compatibility with future devices, reserved bits should be written to zero if accessed. Reserved I/O memory addresses
should never be written.
2. I/O Registers within the address range 0x00 - 0x1F are directly bit-accessible using the SBI and CBI instructions. In these
registers, the value of single bits can be checked by using the SBIS and SBIC instructions.
3. Some of the Status Flags are cleared by writing a logical one to them. Note that, unlike most other AVRs, the CBI and SBI
instructions will only operate on the specified bit, and can therefore be used on registers containing such Status Flags. The
CBI and SBI instructions work with registers 0x00 to 0x1F only.
4. When using the I/O specific commands IN and OUT, the I/O addresses 0x00 - 0x3F must be used. When addressing I/O
Registers as data space using LD and ST instructions, 0x20 must be added to these addresses. The
ATmega48A/48PA/88A/88PA/168A/168PA/328/328P is a complex microcontroller with more peripheral units than can be
supported within the 64 location reserved in Opcode for the IN and OUT instructions. For the Extended I/O space from 0x60
- 0xFF in SRAM, only the ST/STS/STD and LD/LDS/LDD instructions can be used.
5. Only valid for ATmega88A/88PA/168A/168PA/328/328P.
6. BODS and BODSE only available for picoPower devices ATmega48PA/88PA/168PA/328P
11
8271BS–AVR–04/10
ATmega48A/48PA/88A/88PA/168A/168PA/328/328P
5. Instruction Set Summary
Mnemonics
Operands
Description
Operation
Flags
#Clocks
ARITHMETIC AND LOGIC INSTRUCTIONS
ADD
Rd, Rr
Rd, Rr
Rdl,K
Rd, Rr
Rd, K
Rd, Rr
Rd, K
Rdl,K
Rd, Rr
Rd, K
Rd, Rr
Rd, K
Rd, Rr
Rd
Add two Registers
Rd ← Rd + Rr
Z,C,N,V,H
Z,C,N,V,H
Z,C,N,V,S
Z,C,N,V,H
Z,C,N,V,H
Z,C,N,V,H
Z,C,N,V,H
Z,C,N,V,S
Z,N,V
1
1
2
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
ADC
Add with Carry two Registers
Add Immediate to Word
Subtract two Registers
Subtract Constant from Register
Subtract with Carry two Registers
Subtract with Carry Constant from Reg.
Subtract Immediate from Word
Logical AND Registers
Logical AND Register and Constant
Logical OR Registers
Rd ← Rd + Rr + C
Rdh:Rdl ← Rdh:Rdl + K
Rd ← Rd - Rr
ADIW
SUB
SUBI
SBC
Rd ← Rd - K
Rd ← Rd - Rr - C
Rd ← Rd - K - C
Rdh:Rdl ← Rdh:Rdl - K
Rd ← Rd • Rr
SBCI
SBIW
AND
ANDI
OR
Rd ← Rd • K
Z,N,V
Rd ← Rd v Rr
Z,N,V
ORI
Logical OR Register and Constant
Exclusive OR Registers
One’s Complement
Rd ← Rd v K
Z,N,V
EOR
COM
NEG
SBR
Rd ← Rd ⊕ Rr
Z,N,V
Rd ← 0xFF − Rd
Rd ← 0x00 − Rd
Rd ← Rd v K
Z,C,N,V
Z,C,N,V,H
Z,N,V
Rd
Two’s Complement
Rd,K
Rd,K
Rd
Set Bit(s) in Register
CBR
Clear Bit(s) in Register
Increment
Rd ← Rd • (0xFF - K)
Rd ← Rd + 1
Z,N,V
INC
Z,N,V
DEC
Rd
Decrement
Rd ← Rd − 1
Z,N,V
TST
Rd
Test for Zero or Minus
Clear Register
Rd ← Rd • Rd
Z,N,V
CLR
Rd
Rd ← Rd ⊕ Rd
Rd ← 0xFF
Z,N,V
SER
Rd
Set Register
None
MUL
Rd, Rr
Rd, Rr
Rd, Rr
Rd, Rr
Rd, Rr
Rd, Rr
Multiply Unsigned
R1:R0 ← Rd x Rr
R1:R0 ← Rd x Rr
R1:R0 ← Rd x Rr
R1:R0 ← (Rd x Rr) << 1
R1:R0 ← (Rd x Rr) << 1
R1:R0 ← (Rd x Rr) << 1
Z,C
MULS
MULSU
FMUL
FMULS
FMULSU
Multiply Signed
Z,C
Multiply Signed with Unsigned
Fractional Multiply Unsigned
Fractional Multiply Signed
Fractional Multiply Signed with Unsigned
Z,C
Z,C
Z,C
Z,C
BRANCH INSTRUCTIONS
RJMP
k
Relative Jump
PC ← PC + k + 1
None
None
None
None
None
None
None
I
2
2
IJMP
Indirect Jump to (Z)
PC ← Z
JMP(1)
RCALL
ICALL
CALL(1)
RET
k
k
Direct Jump
PC ← k
3
Relative Subroutine Call
Indirect Call to (Z)
PC ← PC + k + 1
3
PC ← Z
3
k
Direct Subroutine Call
Subroutine Return
PC ← k
4
PC ← STACK
4
RETI
Interrupt Return
PC ← STACK
4
CPSE
CP
Rd,Rr
Compare, Skip if Equal
Compare
if (Rd = Rr) PC ← PC + 2 or 3
Rd − Rr
None
Z, N,V,C,H
Z, N,V,C,H
Z, N,V,C,H
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
1/2/3
1
Rd,Rr
CPC
Rd,Rr
Compare with Carry
Rd − Rr − C
1
CPI
Rd,K
Compare Register with Immediate
Skip if Bit in Register Cleared
Skip if Bit in Register is Set
Skip if Bit in I/O Register Cleared
Skip if Bit in I/O Register is Set
Branch if Status Flag Set
Branch if Status Flag Cleared
Branch if Equal
Rd − K
1
SBRC
SBRS
SBIC
Rr, b
if (Rr(b)=0) PC ← PC + 2 or 3
if (Rr(b)=1) PC ← PC + 2 or 3
if (P(b)=0) PC ← PC + 2 or 3
if (P(b)=1) PC ← PC + 2 or 3
if (SREG(s) = 1) then PC←PC+k + 1
if (SREG(s) = 0) then PC←PC+k + 1
if (Z = 1) then PC ← PC + k + 1
if (Z = 0) then PC ← PC + k + 1
if (C = 1) then PC ← PC + k + 1
if (C = 0) then PC ← PC + k + 1
if (C = 0) then PC ← PC + k + 1
if (C = 1) then PC ← PC + k + 1
if (N = 1) then PC ← PC + k + 1
if (N = 0) then PC ← PC + k + 1
if (N ⊕ V= 0) then PC ← PC + k + 1
if (N ⊕ V= 1) then PC ← PC + k + 1
if (H = 1) then PC ← PC + k + 1
if (H = 0) then PC ← PC + k + 1
if (T = 1) then PC ← PC + k + 1
if (T = 0) then PC ← PC + k + 1
if (V = 1) then PC ← PC + k + 1
if (V = 0) then PC ← PC + k + 1
1/2/3
1/2/3
1/2/3
1/2/3
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
Rr, b
P, b
P, b
s, k
s, k
k
SBIS
BRBS
BRBC
BREQ
BRNE
BRCS
BRCC
BRSH
BRLO
BRMI
BRPL
BRGE
BRLT
BRHS
BRHC
BRTS
BRTC
BRVS
BRVC
k
Branch if Not Equal
k
Branch if Carry Set
k
Branch if Carry Cleared
Branch if Same or Higher
Branch if Lower
k
k
k
Branch if Minus
k
Branch if Plus
k
Branch if Greater or Equal, Signed
Branch if Less Than Zero, Signed
Branch if Half Carry Flag Set
Branch if Half Carry Flag Cleared
Branch if T Flag Set
k
k
k
k
k
Branch if T Flag Cleared
Branch if Overflow Flag is Set
Branch if Overflow Flag is Cleared
k
k
12
8271BS–AVR–04/10
ATmega48A/48PA/88A/88PA/168A/168PA/328/328P
Mnemonics
Operands
Description
Operation
Flags
#Clocks
BRIE
BRID
k
k
Branch if Interrupt Enabled
if ( I = 1) then PC ← PC + k + 1
if ( I = 0) then PC ← PC + k + 1
None
1/2
1/2
Branch if Interrupt Disabled
None
BIT AND BIT-TEST INSTRUCTIONS
SBI
P,b
P,b
Rd
Rd
Rd
Rd
Rd
Rd
s
Set Bit in I/O Register
Clear Bit in I/O Register
Logical Shift Left
I/O(P,b) ← 1
None
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
CBI
I/O(P,b) ← 0
None
LSL
Rd(n+1) ← Rd(n), Rd(0) ← 0
Z,C,N,V
LSR
ROL
ROR
ASR
SWAP
BSET
BCLR
BST
BLD
SEC
CLC
SEN
CLN
SEZ
CLZ
SEI
Logical Shift Right
Rd(n) ← Rd(n+1), Rd(7) ← 0
Z,C,N,V
Rotate Left Through Carry
Rotate Right Through Carry
Arithmetic Shift Right
Swap Nibbles
Rd(0)←C,Rd(n+1)← Rd(n),C←Rd(7)
Z,C,N,V
Rd(7)←C,Rd(n)← Rd(n+1),C←Rd(0)
Z,C,N,V
Rd(n) ← Rd(n+1), n=0...6
Z,C,N,V
Rd(3...0)←Rd(7...4),Rd(7...4)←Rd(3...0)
None
Flag Set
SREG(s) ← 1
SREG(s) ← 0
T ← Rr(b)
Rd(b) ← T
C ← 1
SREG(s)
s
Flag Clear
SREG(s)
Rr, b
Rd, b
Bit Store from Register to T
Bit load from T to Register
Set Carry
T
None
C
C
N
N
Z
Clear Carry
C ← 0
Set Negative Flag
N ← 1
Clear Negative Flag
Set Zero Flag
N ← 0
Z ← 1
Clear Zero Flag
Z ← 0
Z
Global Interrupt Enable
Global Interrupt Disable
Set Signed Test Flag
Clear Signed Test Flag
Set Twos Complement Overflow.
Clear Twos Complement Overflow
Set T in SREG
I ← 1
I
CLI
I ← 0
I
SES
CLS
SEV
CLV
SET
CLT
SEH
CLH
S ← 1
S
S
V
V
T
S ← 0
V ← 1
V ← 0
T ← 1
Clear T in SREG
T ← 0
T
Set Half Carry Flag in SREG
Clear Half Carry Flag in SREG
H ← 1
H
H
H ← 0
DATA TRANSFER INSTRUCTIONS
MOV
MOVW
LDI
LD
Rd, Rr
Rd, Rr
Rd, K
Move Between Registers
Copy Register Word
Rd ← Rr
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
-
Rd+1:Rd ← Rr+1:Rr
Load Immediate
Rd ← K
Rd, X
Load Indirect
Rd ← (X)
LD
Rd, X+
Rd, - X
Rd, Y
Load Indirect and Post-Inc.
Load Indirect and Pre-Dec.
Load Indirect
Rd ← (X), X ← X + 1
X ← X - 1, Rd ← (X)
Rd ← (Y)
LD
LD
LD
Rd, Y+
Rd, - Y
Rd,Y+q
Rd, Z
Load Indirect and Post-Inc.
Load Indirect and Pre-Dec.
Load Indirect with Displacement
Load Indirect
Rd ← (Y), Y ← Y + 1
Y ← Y - 1, Rd ← (Y)
Rd ← (Y + q)
Rd ← (Z)
LD
LDD
LD
LD
Rd, Z+
Rd, -Z
Rd, Z+q
Rd, k
Load Indirect and Post-Inc.
Load Indirect and Pre-Dec.
Load Indirect with Displacement
Load Direct from SRAM
Store Indirect
Rd ← (Z), Z ← Z+1
Z ← Z - 1, Rd ← (Z)
Rd ← (Z + q)
Rd ← (k)
LD
LDD
LDS
ST
X, Rr
(X) ← Rr
ST
X+, Rr
- X, Rr
Y, Rr
Store Indirect and Post-Inc.
Store Indirect and Pre-Dec.
Store Indirect
(X) ← Rr, X ← X + 1
X ← X - 1, (X) ← Rr
(Y) ← Rr
ST
ST
ST
Y+, Rr
- Y, Rr
Y+q,Rr
Z, Rr
Store Indirect and Post-Inc.
Store Indirect and Pre-Dec.
Store Indirect with Displacement
Store Indirect
(Y) ← Rr, Y ← Y + 1
Y ← Y - 1, (Y) ← Rr
(Y + q) ← Rr
ST
STD
ST
(Z) ← Rr
ST
Z+, Rr
-Z, Rr
Z+q,Rr
k, Rr
Store Indirect and Post-Inc.
Store Indirect and Pre-Dec.
Store Indirect with Displacement
Store Direct to SRAM
Load Program Memory
Load Program Memory
Load Program Memory and Post-Inc
Store Program Memory
In Port
(Z) ← Rr, Z ← Z + 1
Z ← Z - 1, (Z) ← Rr
(Z + q) ← Rr
ST
STD
STS
LPM
LPM
LPM
SPM
IN
(k) ← Rr
R0 ← (Z)
Rd, Z
Rd ← (Z)
Rd, Z+
Rd ← (Z), Z ← Z+1
(Z) ← R1:R0
Rd, P
P, Rr
Rr
Rd ← P
1
1
2
OUT
PUSH
Out Port
P ← Rr
Push Register on Stack
STACK ← Rr
13
8271BS–AVR–04/10
ATmega48A/48PA/88A/88PA/168A/168PA/328/328P
Mnemonics
Operands
Description
Operation
Flags
#Clocks
POP
Rd
Pop Register from Stack
Rd ← STACK
None
2
MCU CONTROL INSTRUCTIONS
NOP
No Operation
Sleep
None
None
None
None
1
1
SLEEP
WDR
(see specific descr. for Sleep function)
(see specific descr. for WDR/timer)
For On-chip Debug Only
Watchdog Reset
Break
1
BREAK
N/A
Note:
1. These instructions are only available in ATmega168PA and ATmega328P.
14
8271BS–AVR–04/10
ATmega48A/48PA/88A/88PA/168A/168PA/328/328P
6. Ordering Information
6.1
ATmega48A
Speed (MHz)
Power Supply
Ordering Code(2)
Package(1)
Operational Range
ATmega48A-AU
32A
32A
ATmega48A-AUR(5)
ATmega48A-MMH(4)
ATmega48A-MMHR(4)(5)
ATmega48A-MU
28M1
28M1
32M1-A
32M1-A
28P3
Industrial
(-40°C to 85°C)
20(3)
1.8 - 5.5
ATmega48A-MUR(5)
ATmega48A-PU
Note:
1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information
and minimum quantities.
2. Pb-free packaging complies to the European Directive for Restriction of Hazardous Substances (RoHS directive).Also
Halide free and fully Green.
3. See ”Speed Grades” on page 321.
4. NiPdAu Lead Finish.
5. Tape & Reel.
Package Type
32A
32-lead, Thin (1.0 mm) Plastic Quad Flat Package (TQFP)
28M1
28-pad, 4 x 4 x 1.0 body, Lead Pitch 0.45 mm Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF)
32M1-A
28P3
32-pad, 5 x 5 x 1.0 body, Lead Pitch 0.50 mm Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF)
28-lead, 0.300” Wide, Plastic Dual Inline Package (PDIP)
15
8271BS–AVR–04/10
ATmega48A/48PA/88A/88PA/168A/168PA/328/328P
6.2
ATmega48PA
Speed (MHz)
Power Supply
Ordering Code(2)
Package(1)
Operational Range
ATmega48PA-AU
32A
32A
ATmega48PA-AUR(5)
ATmega48PA-MMH(4)
ATmega48PA-MMHR(4)(5)
ATmega48PA-MU
28M1
28M1
32M1-A
32M1-A
28P3
Industrial
(-40°C to 85°C)
20(3)
1.8 - 5.5
ATmega48PA-MUR(5)
ATmega48PA-PU
Note:
1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information
and minimum quantities.
2. Pb-free packaging complies to the European Directive for Restriction of Hazardous Substances (RoHS directive).Also
Halide free and fully Green.
3. See ”Speed Grades” on page 321.
4. NiPdAu Lead Finish.
5. Tape & Reel.
Package Type
32A
32-lead, Thin (1.0 mm) Plastic Quad Flat Package (TQFP)
28M1
28-pad, 4 x 4 x 1.0 body, Lead Pitch 0.45 mm Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF)
32M1-A
28P3
32-pad, 5 x 5 x 1.0 body, Lead Pitch 0.50 mm Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF)
28-lead, 0.300” Wide, Plastic Dual Inline Package (PDIP)
16
8271BS–AVR–04/10
ATmega48A/48PA/88A/88PA/168A/168PA/328/328P
6.3
ATmega88A
Speed (MHz)
Power Supply
Ordering Code(2)
Package(1)
Operational Range
ATmega88A-AU
32A
32A
ATmega88A-AUR(5)
ATmega88A-MMH(4)
ATmega88A-MMHR(4)(5)
ATmega88A-MU
28M1
28M1
32M1-A
32M1-A
28P3
Industrial
(-40°C to 85°C)
20(3)
1.8 - 5.5
ATmega88A-MUR(5)
ATmega88A-PU
Note:
1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information
and minimum quantities.
2. Pb-free packaging complies to the European Directive for Restriction of Hazardous Substances (RoHS directive).Also
Halide free and fully Green.
3. See ”Speed Grades” on page 321.
4. NiPdAu Lead Finish.
5. Tape & Reel.
Package Type
32A
32-lead, Thin (1.0 mm) Plastic Quad Flat Package (TQFP)
28M1
28-pad, 4 x 4 x 1.0 body, Lead Pitch 0.45 mm Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF)
32M1-A
28P3
32-pad, 5 x 5 x 1.0 body, Lead Pitch 0.50 mm Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF)
28-lead, 0.300” Wide, Plastic Dual Inline Package (PDIP)
17
8271BS–AVR–04/10
ATmega48A/48PA/88A/88PA/168A/168PA/328/328P
6.4
ATmega88PA
Speed (MHz)
Power Supply (V)
Ordering Code(2)
Package(1)
Operational Range
ATmega88PA-AU
32A
32A
ATmega88PA-AUR(5)
ATmega88PA-MMH(4)
ATmega88PA-MMHR(4)(5)
ATmega88PA-MU
28M1
28M1
32M1-A
32M1-A
28P3
Industrial
(-40°C to 85°C)
20(3)
1.8 - 5.5
ATmega88PA-MUR(5)
ATmega88PA-PU
Note:
1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information
and minimum quantities.
2. Pb-free packaging complies to the European Directive for Restriction of Hazardous Substances (RoHS directive).Also
Halide free and fully Green.
3. See ”Speed Grades” on page 321.
4. NiPdAu Lead Finish.
5. Tape & Reel.
Package Type
32A
32-lead, Thin (1.0 mm) Plastic Quad Flat Package (TQFP)
28M1
28-pad, 4 x 4 x 1.0 body, Lead Pitch 0.45 mm Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF)
32M1-A
28P3
32-pad, 5 x 5 x 1.0 body, Lead Pitch 0.50 mm Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF)
28-lead, 0.300” Wide, Plastic Dual Inline Package (PDIP)
18
8271BS–AVR–04/10
ATmega48A/48PA/88A/88PA/168A/168PA/328/328P
6.5
ATmega168A
Speed (MHz)(3)
Power Supply (V)
Ordering Code(2)
Package(1)
Operational Range
ATmega168A-AU
32A
32A
ATmega168A-AUR(5)
ATmega168A-MMH(4)
ATmega168A-MMHR(4)(5)
ATmega168A-MU
28M1
28M1
32M1-A
32M1-A
28P3
Industrial
(-40°C to 85°C)
20
1.8 - 5.5
ATmega168A-MUR(5)
ATmega168A-PU
Note:
1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information
and minimum quantities.
2. Pb-free packaging complies to the European Directive for Restriction of Hazardous Substances (RoHS directive).Also
Halide free and fully Green.
3. See ”Speed Grades” on page 321
4. NiPdAu Lead Finish.
5. Tape & Reel.
Package Type
32A
32-lead, Thin (1.0 mm) Plastic Quad Flat Package (TQFP)
28M1
28-pad, 4 x 4 x 1.0 body, Lead Pitch 0.45 mm Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF)
32M1-A
28P3
32-pad, 5 x 5 x 1.0 body, Lead Pitch 0.50 mm Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF)
28-lead, 0.300” Wide, Plastic Dual Inline Package (PDIP)
19
8271BS–AVR–04/10
ATmega48A/48PA/88A/88PA/168A/168PA/328/328P
6.6
ATmega168PA
Speed (MHz)(3)
Power Supply (V)
Ordering Code(2)
Package(1)
Operational Range
ATmega168PA-AU
32A
32A
ATmega168PA-AUR(5)
ATmega168PA-MMH(4)
ATmega168PA-MMHR(4)(5)
ATmega168PA-MU
28M1
28M1
32M1-A
32M1-A
28P3
Industrial
(-40°C to 85°C)
20
1.8 - 5.5
ATmega168PA-MUR(5)
ATmega168PA-PU
Note:
1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information
and minimum quantities.
2. Pb-free packaging complies to the European Directive for Restriction of Hazardous Substances (RoHS directive).Also
Halide free and fully Green.
3. See ”Speed Grades” on page 321.
4. NiPdAu Lead Finish.
5. Tape & Reel.
Package Type
32A
32-lead, Thin (1.0 mm) Plastic Quad Flat Package (TQFP)
28M1
28-pad, 4 x 4 x 1.0 body, Lead Pitch 0.45 mm Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF)
32M1-A
28P3
32-pad, 5 x 5 x 1.0 body, Lead Pitch 0.50 mm Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF)
28-lead, 0.300” Wide, Plastic Dual Inline Package (PDIP)
20
8271BS–AVR–04/10
ATmega48A/48PA/88A/88PA/168A/168PA/328/328P
6.7
ATmega328
Speed (MHz)
Power Supply (V)
Ordering Code(2)
Package(1)
Operational Range
ATmega328-AU
32A
32A
32M1-A
32M1-A
28P3
ATmega328-AUR(4)
ATmega328-MU
ATmega328-MUR(4)
ATmega328-PU
Industrial
(-40°C to 85°C)
20(3)
1.8 - 5.5
Note:
1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information
and minimum quantities.
2. Pb-free packaging complies to the European Directive for Restriction of Hazardous Substances (RoHS directive).Also
Halide free and fully Green.
3. See Figure 28-1 on page 321.
4. Tape & Reel
Package Type
32-lead, Thin (1.0 mm) Plastic Quad Flat Package (TQFP)
28-lead, 0.300” Wide, Plastic Dual Inline Package (PDIP)
32A
28P3
32M1-A
32-pad, 5 x 5 x 1.0 body, Lead Pitch 0.50 mm Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF)
21
8271BS–AVR–04/10
ATmega48A/48PA/88A/88PA/168A/168PA/328/328P
6.8
ATmega328P
Speed (MHz)
Power Supply
Ordering Code(2)
Package(1)
Operational Range
ATmega328P-AU
ATmega328P-AUR(4)
ATmega328P-MU
ATmega328P-MUR(4)
ATmega328P-PU
32A
32A
32M1-A
32M1-A
28P3
Industrial
(-40°C to 85°C)
20(3)
1.8 - 5.5
Note:
1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information
and minimum quantities.
2. Pb-free packaging complies to the European Directive for Restriction of Hazardous Substances (RoHS directive).Also
Halide free and fully Green.
3. See Figure 28-1 on page 321.
4. Tape & Reel.
Package Type
32-lead, Thin (1.0 mm) Plastic Quad Flat Package (TQFP)
28-lead, 0.300” Wide, Plastic Dual Inline Package (PDIP)
32A
28P3
32M1-A
32-pad, 5 x 5 x 1.0 body, Lead Pitch 0.50 mm Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF)
22
8271BS–AVR–04/10
ATmega48A/48PA/88A/88PA/168A/168PA/328/328P
7. Packaging Information
7.1
32A
PIN 1
B
PIN 1 IDENTIFIER
E1
E
e
D1
D
C
0˚~7˚
A2
A
A1
L
COMMON DIMENSIONS
(Unit of Measure = mm)
MIN
–
MAX
1.20
0.15
1.05
9.25
7.10
9.25
7.10
0.45
0.20
0.75
NOM
NOTE
SYMBOL
A
–
–
A1
A2
D
0.05
0.95
8.75
6.90
8.75
6.90
0.30
0.09
0.45
1.00
9.00
7.00
9.00
7.00
–
D1
E
Note 2
Note 2
Notes:
1. This package conforms to JEDEC reference MS-026, Variation ABA.
2. Dimensions D1 and E1 do not include mold protrusion. Allowable
protrusion is 0.25 mm per side. Dimensions D1 and E1 are maximum
plastic body size dimensions including mold mismatch.
E1
B
C
–
3. Lead coplanarity is 0.10 mm maximum.
L
–
e
0.80 TYP
10/5/2001
TITLE
DRAWING NO. REV.
2325 Orchard Parkway
San Jose, CA 95131
32A, 32-lead, 7 x 7 mm Body Size, 1.0 mm Body Thickness,
0.8 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP)
32A
B
R
23
8271BS–AVR–04/10
ATmega48A/48PA/88A/88PA/168A/168PA/328/328P
7.2
28M1
D
C
1
2
3
Pin 1 ID
E
SIDE VIEW
A1
TOP VIEW
A
y
K
D2
0.45
E2
COMMON DIMENSIONS
(Unit of Measure = mm)
1
2
3
R 0.20
MIN
MAX
NOM
NOTE
SYMBOL
A
0.80
0.90
1.00
A1
b
0.00
0.17
0.02
0.22
0.20 REF
4.00
2.40
4.00
2.40
0.45
0.40
–
0.05
0.27
b
C
D
D2
E
3.95
2.35
3.95
2.35
4.05
2.45
4.05
2.45
L
e
E2
e
0.4 Ref
(4x)
BOTTOM VIEW
L
0.35
0.00
0.20
0.45
0.08
–
y
K
–
The terminal #1 ID is a Laser-marked Feature.
Note:
10/24/08
GPC
DRAWING NO.
TITLE
REV.
28M1, 28-pad,4 x 4 x 1.0 mm Body, Lead Pitch 0.45 mm,
2.4 x 2.4 mm Exposed Pad, Thermally Enhanced
Plastic Very Thin Quad Flat No Lead Package (VQFN)
Package Drawing Contact:
packagedrawings@atmel.com
ZBV
28M1
B
24
8271BS–AVR–04/10
ATmega48A/48PA/88A/88PA/168A/168PA/328/328P
7.3
32M1-A
D
D1
1
2
3
0
Pin 1 ID
SIDE VIEW
E1
E
TOP VIEW
A3
A1
A2
A
K
COMMON DIMENSIONS
0.08
C
(Unit of Measure = mm)
P
D2
MIN
0.80
–
MAX
1.00
0.05
1.00
NOM
0.90
0.02
0.65
0.20 REF
0.23
5.00
4.75
3.10
5.00
4.75
3.10
0.50 BSC
0.40
–
NOTE
SYMBOL
A
A1
A2
A3
b
1
2
3
P
–
Pin #1 Notch
(0.20 R)
E2
0.18
4.90
4.70
2.95
4.90
4.70
2.95
0.30
5.10
4.80
3.25
5.10
4.80
3.25
D
K
D1
D2
E
e
b
L
E1
E2
e
BOTTOM VIEW
L
0.30
–
0.50
0.60
P
o
–
–
12
0
Note: JEDEC Standard MO-220, Fig. 2 (Anvil Singulation), VHHD-2.
K
0.20
–
–
5/25/06
DRAWING NO. REV.
32M1-A
TITLE
2325 Orchard Parkway
San Jose, CA 95131
32M1-A, 32-pad, 5 x 5 x 1.0 mm Body, Lead Pitch 0.50 mm,
3.10 mm Exposed Pad, Micro Lead Frame Package (MLF)
E
R
25
8271BS–AVR–04/10
ATmega48A/48PA/88A/88PA/168A/168PA/328/328P
7.4
28P3
D
PIN
1
E1
A
SEATING PLANE
A1
B2
(4 PLACES)
L
B
B1
e
E
COMMON DIMENSIONS
(Unit of Measure = mm)
0º ~ 15º REF
C
MIN
–
MAX
4.5724
–
NOM
NOTE
SYMBOL
A
–
–
–
–
–
–
–
–
–
–
–
eB
A1
D
0.508
34.544
7.620
7.112
0.381
1.143
0.762
3.175
0.203
–
34.798 Note 1
8.255
E
E1
B
7.493 Note 1
0.533
B1
B2
L
1.397
Note:
1. Dimensions D and E1 do not include mold Flash or Protrusion.
Mold Flash or Protrusion shall not exceed 0.25 mm (0.010").
1.143
3.429
C
0.356
eB
e
10.160
2.540 TYP
09/28/01
DRAWING NO. REV.
28P3
TITLE
2325 Orchard Parkway
San Jose, CA 95131
28P3, 28-lead (0.300"/7.62 mm Wide) Plastic Dual
Inline Package (PDIP)
B
R
26
8271BS–AVR–04/10
ATmega48A/48PA/88A/88PA/168A/168PA/328/328P
8. Errata
8.1
Errata ATmega48A
The revision letter in this section refers to the revision of the ATmega48A device.
8.1.1
Rev. D
• Analog MUX can be turned off when setting ACME bit
1. Analog MUX can be turned off when setting ACME bit
If the ACME (Analog Comparator Multiplexer Enabled) bit in ADCSRB is set while MUX3 in
ADMUX is '1' (ADMUX[3:0]=1xxx), all MUX'es are turned off until the ACME bit is cleared.
Problem Fix/Workaround
Clear the MUX3 bit before setting the ACME bit.
8.2
Errata ATmega48PA
The revision letter in this section refers to the revision of the ATmega48PA device.
8.2.1
Rev. D
• Analog MUX can be turned off when setting ACME bit
1. Analog MUX can be turned off when setting ACME bit
If the ACME (Analog Comparator Multiplexer Enabled) bit in ADCSRB is set while MUX3 in
ADMUX is '1' (ADMUX[3:0]=1xxx), all MUX'es are turned off until the ACME bit is cleared.
Problem Fix/Workaround
Clear the MUX3 bit before setting the ACME bit.
8.3
Errata ATmega88A
The revision letter in this section refers to the revision of the ATmega88A device.
8.3.1
Rev. F
• Analog MUX can be turned off when setting ACME bit
1. Analog MUX can be turned off when setting ACME bit
If the ACME (Analog Comparator Multiplexer Enabled) bit in ADCSRB is set while MUX3 in
ADMUX is '1' (ADMUX[3:0]=1xxx), all MUX'es are turned off until the ACME bit is cleared.
Problem Fix/Workaround
Clear the MUX3 bit before setting the ACME bit.
27
8271BS–AVR–04/10
ATmega48A/48PA/88A/88PA/168A/168PA/328/328P
8.4
Errata ATmega88PA
The revision letter in this section refers to the revision of the ATmega88PA device.
8.4.1
Rev. F
• Analog MUX can be turned off when setting ACME bit
1. Analog MUX can be turned off when setting ACME bit
If the ACME (Analog Comparator Multiplexer Enabled) bit in ADCSRB is set while MUX3 in
ADMUX is '1' (ADMUX[3:0]=1xxx), all MUX'es are turned off until the ACME bit is cleared.
Problem Fix/Workaround
Clear the MUX3 bit before setting the ACME bit.
8.5
Errata ATmega168A
The revision letter in this section refers to the revision of the ATmega168A device.
8.5.1
Rev. E
• Analog MUX can be turned off when setting ACME bit
1. Analog MUX can be turned off when setting ACME bit
If the ACME (Analog Comparator Multiplexer Enabled) bit in ADCSRB is set while MUX3 in
ADMUX is '1' (ADMUX[3:0]=1xxx), all MUX'es are turned off until the ACME bit is cleared.
Problem Fix/Workaround
Clear the MUX3 bit before setting the ACME bit.
8.6
Errata ATmega168PA
The revision letter in this section refers to the revision of the ATmega168PA device.
8.6.1
Rev E
• Analog MUX can be turned off when setting ACME bit
1. Analog MUX can be turned off when setting ACME bit
If the ACME (Analog Comparator Multiplexer Enabled) bit in ADCSRB is set while MUX3 in
ADMUX is '1' (ADMUX[3:0]=1xxx), all MUX'es are turned off until the ACME bit is cleared.
Problem Fix/Workaround
Clear the MUX3 bit before setting the ACME bit.
28
8271BS–AVR–04/10
ATmega48A/48PA/88A/88PA/168A/168PA/328/328P
8.7
Errata ATmega328
The revision letter in this section refers to the revision of the ATmega328 device.
8.7.1
Rev D
• Analog MUX can be turned off when setting ACME bit
1. Analog MUX can be turned off when setting ACME bit
If the ACME (Analog Comparator Multiplexer Enabled) bit in ADCSRB is set while MUX3 in
ADMUX is '1' (ADMUX[3:0]=1xxx), all MUX'es are turned off until the ACME bit is cleared.
Problem Fix/Workaround
Clear the MUX3 bit before setting the ACME bit.
8.7.2
8.7.3
Rev C
Rev B
Not sampled.
• Analog MUX can be turned off when setting ACME bit
• Unstable 32 kHz Oscillator
1. Unstable 32 kHz Oscillator
If the ACME (Analog Comparator Multiplexer Enabled) bit in ADCSRB is set while MUX3 in
ADMUX is '1' (ADMUX[3:0]=1xxx), all MUX'es are turned off until the ACME bit is cleared.
Problem Fix/Workaround
Clear the MUX3 bit before setting the ACME bit.
2. Unstable 32 kHz Oscillator
The 32 kHz oscillator does not work as system clock. The 32 kHz oscillator used as asyn-
chronous timer is inaccurate.
Problem Fix/ Workaround
None.
8.7.4
Rev A
• Analog MUX can be turned off when setting ACME bit
• Unstable 32 kHz Oscillator
1. Unstable 32 kHz Oscillator
If the ACME (Analog Comparator Multiplexer Enabled) bit in ADCSRB is set while MUX3 in
ADMUX is '1' (ADMUX[3:0]=1xxx), all MUX'es are turned off until the ACME bit is cleared.
Problem Fix/Workaround
Clear the MUX3 bit before setting the ACME bit.
2. Unstable 32 kHz Oscillator
The 32 kHz oscillator does not work as system clock. The 32 kHz oscillator used as asyn-
chronous timer is inaccurate.
Problem Fix/ Workaround
None.
29
8271BS–AVR–04/10
ATmega48A/48PA/88A/88PA/168A/168PA/328/328P
8.8
Errata ATmega328P
The revision letter in this section refers to the revision of the ATmega328P device.
8.8.1
Rev D
• Analog MUX can be turned off when setting ACME bit
1. Analog MUX can be turned off when setting ACME bit
If the ACME (Analog Comparator Multiplexer Enabled) bit in ADCSRB is set while MUX3 in
ADMUX is '1' (ADMUX[3:0]=1xxx), all MUX'es are turned off until the ACME bit is cleared.
Problem Fix/Workaround
Clear the MUX3 bit before setting the ACME bit.
8.8.2
8.8.3
Rev C
Rev B
Not sampled.
• Analog MUX can be turned off when setting ACME bit
• Unstable 32 kHz Oscillator
1. Unstable 32 kHz Oscillator
If the ACME (Analog Comparator Multiplexer Enabled) bit in ADCSRB is set while MUX3 in
ADMUX is '1' (ADMUX[3:0]=1xxx), all MUX'es are turned off until the ACME bit is cleared.
Problem Fix/Workaround
Clear the MUX3 bit before setting the ACME bit.
2. Unstable 32 kHz Oscillator
The 32 kHz oscillator does not work as system clock. The 32 kHz oscillator used as asyn-
chronous timer is inaccurate.
Problem Fix/ Workaround
None.
8.8.4
Rev A
• Unstable 32 kHz Oscillator
1. Unstable 32 kHz Oscillator
The 32 kHz oscillator does not work as system clock. The 32 kHz oscillator used as asyn-
chronous timer is inaccurate.
Problem Fix/ Workaround
None.
30
8271BS–AVR–04/10
ATmega48A/48PA/88A/88PA/168A/168PA/328/328P
9. Datasheet Revision History
Please note that the referring page numbers in this section are referred to this document. The
referring revision in this section are referring to the document revision.
9.1
Rev. 8271B-04/10
1.
Updated Table 8-8 with correct value for timer oscilliator at xtal2/tos2
Corrected use of SBIS instructions in assembly code examples.
2.
3.
Corrected BOD and BODSE bits to R/W in Section 9.11.2 on page 45, Section 11.5 on page 69
and Section 13.4 on page 93
4.
5.
Figures for bandgap characterization added, Figure 29-34 on page 349, Figure 29-81 on page
374, Figure 29-128 on page 399, Figure 29-175 on page 424, Figure 29-222 on page 449, Fig-
ure 29-269 on page 474, Figure 29-316 on page 499 and Figure 29-363 on page 523.
Updated ”Packaging Information” on page 546 by replacing 28M1 with a correct corresponding
package.
9.2
Rev. 8271A-12/09
1.
New datasheet 8271 with merged information for ATmega48PA, ATmega88PA,
ATmega168PA and ATmega48A, ATmega88A andATmega168A. Also included
information on ATmega328 and ATmega328P
2
Changes done:
– New devices added: ATmega48A/ATmega88A/ATmega168A and
ATmega328
– Updated Feature Description
– Updated Table 2-1 on page 6
– Added note for BOD Disable on page 40.
– Added note on BOD and BODSE in ”MCUCR – MCU Control Register” on
page 93 and ”Register Description” on page 294
– Added limitation informatin for the application ”Boot Loader Support –
Read-While-Write Self-Programming” on page 279
– Added limitiation information for ”Program And Data Memory Lock Bits” on
page 296
– Added specified DC characteristice per processor
– Added typical characteristics per processor
– Removed execption information in ”Address Match Unit” on page 223.
31
8271BS–AVR–04/10
Headquarters
International
Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131
USA
Tel: 1(408) 441-0311
Fax: 1(408) 487-2600
Atmel Asia
Atmel Europe
Le Krebs
Atmel Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
Tel: (81) 3-3523-3551
Fax: (81) 3-3523-7581
Unit 1-5 & 16, 19/F
BEA Tower, Millennium City 5
418 Kwun Tong Road
Kwun Tong, Kowloon
Hong Kong
8, Rue Jean-Pierre Timbaud
BP 309
78054 Saint-Quentin-en-
Yvelines Cedex
France
Tel: (852) 2245-6100
Fax: (852) 2722-1369
Tel: (33) 1-30-60-70-00
Fax: (33) 1-30-60-71-11
Product Contact
Web Site
Technical Support
Sales Contact
www.atmel.com
avr@atmel.com
www.atmel.com/contacts
Literature Requests
www.atmel.com/literature
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any
intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI-
TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY
WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDEN-
TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF
THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications
and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided
otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use
as components in applications intended to support or sustain life.
© 2010 Atmel Corporation. All rights reserved. Atmel®, Atmel logo and combinations thereof, AVR®, AVR® logo and others are registered trade-
marks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.
8271BS–AVR–04/10
ATMEGA88PA-AUR 替代型号
型号 | 制造商 | 描述 | 替代类型 | 文档 |
ATMEGA88PA-AU | ATMEL | 8-bit Microcontroller with 8K Bytes In-System Programmable Flash | 完全替代 |
ATMEGA88PA-AUR 相关器件
型号 | 制造商 | 描述 | 价格 | 文档 |
ATMEGA88PA-CCU | MICROCHIP | IC MCU 8BIT 8KB FLASH 32UFBGA | 获取价格 | |
ATMEGA88PA-CCUR | MICROCHIP | IC MCU 8BIT 8KB FLASH 32UFBGA | 获取价格 | |
ATMEGA88PA-MMH | ATMEL | 8-bit Microcontroller with 4/8/16/32K Bytes In-System Programmable Flash | 获取价格 | |
ATMEGA88PA-MMHR | ATMEL | 8-bit Microcontroller with 4/8/16/32K Bytes In-System Programmable Flash | 获取价格 | |
ATMEGA88PA-MMNR | MICROCHIP | IC MCU 8BIT 8KB FLASH 28VQFN | 获取价格 | |
ATMEGA88PA-MMUR | MICROCHIP | IC MCU 8BIT 8KB FLASH 28VQFN | 获取价格 | |
ATMEGA88PA-MU | ATMEL | 8-bit Microcontroller with 4/8/16/32K Bytes In-System Programmable Flash | 获取价格 | |
ATMEGA88PA-MUR | ATMEL | 8-bit Microcontroller with 4/8/16/32K Bytes In-System Programmable Flash | 获取价格 | |
ATMEGA88PA-PU | ATMEL | 8-bit Microcontroller with 8K Bytes In-System Programmable Flash | 获取价格 | |
ATmega88PB | ATMEL | Advanced RISC architecture | 获取价格 |
ATMEGA88PA-AUR 相关文章
- 2024-09-20
- 5
- 2024-09-20
- 8
- 2024-09-20
- 8
- 2024-09-20
- 6