HCPL-2212-560E [AVAGO]
1 CHANNEL LOGIC OUTPUT OPTOCOUPLER, 5Mbps, 0.300 INCH, ROHS COMPLIANT, SURFACE MOUNT, DIP-8;
| 型号： | HCPL-2212-560E |
| 厂家： | 
AVAGO TECHNOLOGIES LIMITED |
| 描述： | 1 CHANNEL LOGIC OUTPUT OPTOCOUPLER, 5Mbps, 0.300 INCH, ROHS COMPLIANT, SURFACE MOUNT, DIP-8 光电 栅 |
| 文件： | 总18页 (文件大小：321K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
HCPL-2201, HCPL-2202, HCPL-2211,HCPL-2212,
HCPL-2231, HCPL-2232, HCPL-0201, HCPL-0211,
HCNW2201, HCNW2211
Very High CMR, Wide VCC Logic Gate Optocouplers
Data Sheet
Lead (Pb) Free
RoHS 6 fully
compliant
RoHS 6 fully compliant options available;
-xxxE denotes a lead-free product
Description
Features
• 10 kV/µs minimum Common Mode Rejection
(CMR) at VCM = 1000 V (HCPL-2211/2212/0211/2232,
HCNW2211)
The HCPL-22XX, HCPL-02XX, and HCNW22XX are optical-
ly-coupled logic gates. The HCPL-22XX, and HCPL-02XX
contain a GaAsP LED while the HCNW22XX contains an
AlGaAs LED. The detectors have totem pole output stag-
es and optical receiver input stages with built-in Schmitt
triggerstoprovidelogic-compatiblewaveforms,eliminat-
ing the need for additional waveshaping.
• Wide operating VCC range: 4.5 to 20 Volts
• 300 ns propagation delay guaranteed over the full
temperature range
• 5 Mbd typical signal rate
A superior internal shield on the HCPL-2211/12, HCPL-
0211, HCPL-2232 and HCNW2211 guarantees common
mode transient immunity of 10 kV/µs at a common
mode voltage of 1000 volts.
• Low input current (1.6mA to 1.8 mA)
• Hysteresis
• Totem pole output (no pullup resistor required)
• Available in 8-Pin DIP, SOIC-8, widebody packages
• Guaranteed performance from -40°C to 85°C
• Safety approval
Functional Diagram
HCPL-2201/11
HCPL-0201/11
HCNW2201/11
HCPL-2202/12
– UL recognized -3750 V rms for 1 minute (5000V
rms for 1 minute for HCNW22XX) per UL1577
NC
ANODE
CATHODE
NC
1
2
3
4
8
7
6
5
NC
ANODE
CATHODE
NC
1
2
3
4
8
7
6
5
V
V
V
CC
CC
– CSAapproved
NC
O
– IEC/EN/DIN EN 60747-5-2 approved with V
=
IORM
NC
V
O
630 V peak (HCPL-2211/2212 Option 060 only) and
VIORM = 1414 V peak (HCNW22XX only)
GND
GND
SHIELD
SHIELD
• MIL-PRF-38534 hermetic version available
(HCPL-52XX/62XX)
HCPL-2231/32
ANODE 1
CATHODE 1
CATHODE 2
ANODE 2
1
2
3
4
8
7
6
5
V
V
CC
TRUTH TABLE
Applications
(POSITIVE LOGIC)
LED
V
O
O1
• Isolation of high speed logic systems
• Computer-peripheral interfaces
• Microprocessor system interfaces
• Ground loop elimination
• Pulse transformer replacement
• High speed line receiver
• Power control systems
ON
OFF
HIGH
LOW
V
O2
GND
SHIELD
A 0.1 µF bypass capacitor must be connected between pins 5 and8.
CAUTION: It is advised that normal static precautions be taken in handling and assembly
of this component to prevent damage and/or degradation which may be induced by ESD.
The electrical and switching characteristics of the HCPL-
22XX, HCPL-02XX and HCNW22XX are guaranteed from
-40°C to +85°C and a VCC from 4.5 volts to 20 volts. Low IF
and wide VCC range allow compatibility with TTL, LSTTL,
and CMOS logic and result in lower power consumption
compared to other high speed couplers. Logic signals
are transmitted with a typical propagation delay of
150ns.
Selection Guide
Small-
Outline SO-8
Widebody
(400 Mil)
Minimum CMRInput
8-Pin DIP (300 Mil)
Hermetic
On-
Current
(mA)
Single
Channel
Package
Dual
Channel
Package
Single
Channel
Package
Single
Channel
Package
Single and
Dual Channel
Packages
dV/dt
(V/µs)
V (V)
CM
1,000
50
1.6
HCPL-2200[1,2]
HCPL-2201
HCPL-2202
HCPL-0201
HCPL-0211
HCNW2201
1.8
1.6
1.6
HCPL-2231
HCPL-2232
2,500
5,000[3]
400
300[3]
HCPL-2219[1,2]
HCPL-2211
HCPL-2212
HCNW2211
1.8
2.0
1,000
50
HCPL-52XX[2]
HCPL-62XX[2]
Notes:
1. HCPL-2200/2219 devices include output enable/disable function.
2. Technical data for the HCPL-2200/2219, HCPL-52XX and HCPL-62XX are on separate Avago publications.
3. Minimum CMR of 10 kV/µs with VCM = 1000 V can be achieved with input current, IF, of 5 mA.
Schematic
I
CC
I
V
V
CC
O1
8
7
I
O1
F1
1
+
V
F1
–
I
CC
V
V
CC
O
2
8
5
SHIELD
I
I
O
F
2
3
+
V
F
–
I
O2
3
GND
V
–
V
O2
SHIELD
6
5
F2
HCPL-2201/02/11/12
HCPL-0201/11
HCNW2201/11
+
4
I
F2
GND
SHIELD
HCPL-2231/32
2
Ordering Information
HCPL-2201, HCPL-2202, HCPL-2211, HCPL-2212, HCPL-2231, HCPL-2232, HCPL-0201, HCPL-0211 are UL Recognized
with 3750 Vrms for 1 minute per UL1577.
HCNW2201 and HCNW2211 are UL Recognized with 5000 Vrms for 1 minute per UL1577.
All devices listed above are approved under CSA Component Acceptance Notice #5, File CA 88324.
Option
UL 5000
Vrms/ 1
Minute
rating
Part
number
RoHS
Non RoHS
Compliant Compliant
Surface
Mount
Gull
Wing
Tape &
Reel
IEC/EN/DIN EN
60747-5-2
Package
Quantity
-000E
-300E
-500E
-060E
-360E
-560E
-000E
-300E
-500E
-000E
-500E
-060E
-560E
-000E
-300E
-500E
No option
-300
50 per tube
50 per tube
1000 per reel
50 per tube
50 per tube
1000 per reel
50 per tube
50 per tube
1000 per reel
100 per tube
1500 per reel
100 per tube
1500 per reel
42 per tube
42 per tube
750 per reel
X
X
X
X
HCPL-2201
HCPL-2202
HCPL-2211
HCPL-2212
-500
X
X
300mil
DIP-8
-060
X
X
X
-360
X
X
X
X
-560
No option
-300
HCPL-2231
HCPL-2232
X
X
X
X
X
X
X
X
-500
X
X
X
No option
-500
HCPL-0201
HCPL-0211
SO-8
-060
X
X
X
X
X
-560
No option
-300
X
X
X
400mil
Widebody
DIP-8
HCNW2201
HCNW2211
X
X
X
X
-500
X
To order, choose a part number from the part number column and combine with the desired option from the option
column to form an order entry.
Example 1:
HCPL-2202-560E to order product of 300mil DIP Gull Wing Surface Mount package in Tape and Reel packaging
with IEC/EN/DIN EN 60747-5-2 Safety Approval in RoHS compliant.
Example 2:
HCPL-2202 to order product of 300mil DIP package in tube packaging and non RoHS compliant.
Option datasheets are available. Contact your Avago sales representative or authorized distributor for information.
Remarks: The notation ‘#XXX’ is used for existing products, while (new) products launched since 15th July 2001 and
RoHS compliant option will use ‘-XXXE‘.
3
Package Outline Drawings
8-Pin DIP Package (HCPL-2201/02/11/12/31/32)
7.62 0.25
(0.300 0.010)
9.65 0.25
(0.380 0.010)
8
1
7
6
5
6.35 0.25
(0.250 0.010)
TYPE NUMBER
OPTION CODE*
DATE CODE
A XXXXZ
YYWW
U R
UL
2
3
4
RECOGNITION
1.78 (0.070) MAX.
1.19 (0.047) MAX.
+ 0.076
- 0.051
0.254
5° TYP.
+ 0.003)
- 0.002)
3.56 0.13
(0.140 0.005)
(0.010
4.70 (0.185) MAX.
0.51 (0.020) MIN.
2.92 (0.115) MIN.
DIMENSIONS IN MILLIMETERS AND (INCHES).
1.080 0.320
(0.043 0.013)
0.65 (0.025) MAX.
* MARKING CODE LETTER FOR OPTION NUMBERS
"V" = OPTION 060
OPTION NUMBERS 300 AND 500 NOT MARKED.
2.54 0.25
(0.100 0.010)
NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.
8-Pin DIP Package with Gull Wing Surface Mount Option 300 (HCPL-2201/02/11/12/31/32)
LAND PATTERN RECOMMENDATION
1.016 (0.040)
9.65 0.25
(0.380 0.010)
6
5
8
1
7
6.350 0.25
(0.250 0.010)
10.9 (0.430)
2.0 (0.080)
2
3
4
1.27 (0.050)
9.65 0.25
1.780
(0.070)
MAX.
(0.380 0.010)
1.19
(0.047)
MAX.
7.62 0.25
(0.300 0.010)
+ 0.076
0.254
- 0.051
3.56 0.13
(0.140 0.005)
+ 0.003)
- 0.002)
(0.010
1.080 0.320
(0.043 0.013)
0.635 0.25
(0.025 0.010)
12° NOM.
0.635 0.130
(0.025 0.005)
2.54
(0.100)
BSC
DIMENSIONS IN MILLIMETERS (INCHES).
LEAD COPLANARITY = 0.10 mm (0.004 INCHES).
NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.
4
Small-Outline SO-8 Package (HCPL-0201/11)
LAND PATTERN RECOMMENDATION
8
1
7
6
5
5.994 ± 0.203
(0.236 ± 0.008)
XXX
YWW
3.937 ± 0.127
(0.155 ± 0.005)
7.49 (0.295)
TYPE NUMBER
(LAST 3 DIGITS)
DATE CODE
2
3
4
1.9 (0.075)
PIN ONE
0.406 ± 0.076
(0.016 ± 0.003)
1.270
(0.050)
BSC
0.64 (0.025)
7o
0.432
(0.017)
*
5.080 ± 0.127
(0.200 ± 0.005)
45o X
3.175 ± 0.127
(0.125 ± 0.005)
0 ~ 7o
0.228 ± 0.025
(0.009 ± 0.001)
1.524
(0.060)
0.203 ± 0.102
(0.008 ± 0.004)
TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH)
5.207 ± 0.254 (0.205 ± 0.010)
*
0.305
(0.012)
MIN.
DIMENSIONS IN MILLIMETERS (INCHES).
LEAD COPLANARITY = 0.10 mm (0.004 INCHES) MAX.
NOTE: FLOATING LEAD PROTRUSION IS 0.15 mm (6 mils) MAX.
8-Pin Widebody DIP Package (HCNW2201/11)
11.00
(0.433)
11.23 ± 0.15
(0.442 ± 0.006)
MAX.
9.00 ± 0.15
(0.354 ± 0.006)
7
6
5
8
TYPE NUMBER
A
DATE CODE
HCNWXXXX
YYWW
1
3
2
4
10.16 (0.400)
TYP.
1.55
(0.061)
MAX.
7o TYP.
+ 0.076
- 0.0051
0.254
+ 0.003)
- 0.002)
(0.010
5.10
(0.201)
MAX.
3.10 (0.122)
3.90 (0.154)
0.51 (0.021) MIN.
2.54 (0.100)
TYP.
1.80 ± 0.15
(0.071 ± 0.006)
0.40 (0.016)
0.56 (0.022)
DIMENSIONS IN MILLIMETERS (INCHES).
NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.
5
8-Pin Widebody DIP Package with Gull Wing Surface Mount Option 300 (HCNW2201/11)
11.23 ± 0.15
(0.442 ± 0.006)
LAND PATTERN RECOMMENDATION
7
6
5
8
9.00 ± 0.15
(0.354 ± 0.006)
13.56
(0.534)
1
3
2
4
2.29
(0.09)
1.3
(0.051)
12.30 ± 0.30
1.55
(0.061)
MAX.
(0.484 ± 0.012)
11.00
MAX.
(0.433)
4.00
(0.158)
MAX.
1.80 ± 0.15
(0.071 ± 0.006)
1.00 ± 0.15
(0.039 ± 0.006)
0.75 ± 0.25
(0.030 ± 0.010)
+ 0.076
- 0.0051
2.54
(0.100)
BSC
0.254
+ 0.003)
- 0.002)
(0.010
DIMENSIONS IN MILLIMETERS (INCHES).
7o NOM.
LEAD COPLANARITY = 0.10 mm (0.004 INCHES).
NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.
Solder Reflow Temperature Profile
300
PREHEATING RATE 3 °C + 1 °C/–0.5 °C/SEC.
REFLOW HEATING RATE 2.5 °C 0.5 °C/SEC.
PEAK
TEMP.
245 °C
PEAK
TEMP.
240 °C
PEAK
TEMP.
230 °C
200
100
0
2.5 C 0.5 °C/SEC.
SOLDERING
TIME
30
160 °C
150 °C
140 °C
SEC.
200 °C
30
SEC.
3 °C + 1 °C/–0.5 °C
PREHEATING TIME
150 °C, 90 + 30 SEC.
50 SEC.
TIGHT
TYPICAL
LOOSE
ROOM
TEMPERATURE
0
50
100
150
200
250
TIME (SECONDS)
NOTE: NON-HALIDE FLUX SHOULD BE USED.
6
Recommended Pb-Free IR Profile
TIME WITHIN 5 °C of ACTUAL
PEAK TEMPERATURE
tp
15 SEC.
* 260 +0/-5 °C
RAMP-UP
Tp
217 °C
TL
NOTES:
RAMP-DOWN
6 °C/SEC. MAX.
3 °C/SEC. MAX.
THE TIME FROM 25 °C to PEAK
150 - 200 °C
Tsmax
Tsmin
TEMPERATURE = 8 MINUTES MAX.
Tsmax = 200 °C, Tsmin = 150 °C
NOTE: NON-HALIDE FLUX SHOULD BE USED.
ts
tL
PREHEAT
60 to 180 SEC.
60 to 150 SEC.
* RECOMMENDED PEAK TEMPERATURE
FOR WIDEBODY 400mils PACKAGE IS 245 °C
25
t 25 °C to PEAK
TIME
Regulatory Information
The HCPL-22XX/02XX and HCNW22XX have been approved by the following organizations:
UL
IEC/EN/DIN EN 60747-5-2
Recognized under UL 1577, Component Recognition
Program, File E55361.
Approved under:
IEC 60747-5-2:1997 + A1:2002
EN 60747-5-2:2001 + A1:2002
DIN EN 60747-5-2 (VDE 0884 Teil 2):2003-01
(Option 060 and HCNW only)
CSA
Approved under CSA Component Acceptance Notice
#5, File CA 88324.
Insulation and Safety Related Specifications
8-pin DIP Package
8-Pin DIP
(300 Mil)
Value
Widebody
(400 Mil)
Value
SO-8
Value
Parameter
Symbol
Units Conditions
Minimum External
Air Gap (External
Clearance)
L(101)
7.1
7.4
4.9
9.6
mm
mm
mm
Measured from input terminals
to output terminals, shortest
distance through air.
Minimum External
Tracking (External
Creepage)
L(102)
4.8
10.0
1.0
Measured from input terminals
to output terminals, shortest
distance path along body.
Minimum Internal
Plastic Gap
(Internal Clearance)
0.08
0.08
Through insulation distance,
conductor to conductor, usually
the direct distance between the
photoemitter and photodetector
inside the optocoupler cavity.
Minimum Internal
Tracking (Internal
Creepage)
NA
200
IIIa
NA
200
IIIa
4.0
200
IIIa
mm
Measured from input terminals
to output terminals, along
internal cavity.
Tracking Resistance
(Comparative
Tracking Index)
CTI
Volts
DIN IEC 112/VDE 0303 Part 1
Isolation Group
Material Group
(DIN VDE 0110, 1/89, Table 1)
Option 300 - surface mount classification is Class A in accordance with CECC 00802.
7
IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics
(HCPL-2211/2212 Option 060 ONLY)
Description
Symbol
Characteristic
Units
Installation classification per DIN VDE 0110/1.89, Table 1
for rated mains voltage ≤300 V rms
I-IV
I-III
for rated mains voltage ≤450 V rms
Climatic Classification
55/85/21
2
Pollution Degree (DIN VDE 0110/1.89)
Maximum Working Insulation Voltage
Input to Output Test Voltage, Method b*
V
630
V peak
V peak
IORM
V
IORM x 1.875 = VPR, 100% Production Test with tm = 1 sec,
VPR
1181
945
Partial Discharge < 5 pC
Input to Output Test Voltage, Method a*
VIORM x 1.5 = VPR, Type and sample test,
tm = 60 sec, Partial Discharge < 5 pC
VPR
V peak
Highest Allowable Overvoltage*
(Transient Overvoltage, tini = 10 sec)
VIOTM
6000
V peak
Safety Limiting Values
(Maximum values allowed in the event of a failure,
also see Figure 12, Thermal Derating curve.)
Case Temperature
Input Current
Output Power
TS
IS,OUTPUT
PS,OUTPUT
175
230
600
°C
mA
mW
Insulation Resistance at TS, VIO = 500 V
RS
≥109
Ω
*Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section IEC/EN/DIN EN 60747-5-2, for a
detailed description.
Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in applica-
tion.
8
IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics
(HCNW22XX ONLY)
Description
Symbol
Characteristic
Units
Installation classification per DIN VDE 0110/1.89, Table 1
for rated mains voltage ≤600 V rms
I-IV
I-III
for rated mains voltage ≤1000 V rms
Climatic Classification
55/100/21
2
Pollution Degree (DIN VDE 0110/1.89)
Maximum Working Insulation Voltage
V
1414
V peak
V peak
IORM
Input to Output Test Voltage, Method b*
VIORM x 1.875 = VPR, 100% Production Test with tm = 1 sec,
Partial Discharge < 5 pC
VPR
2652
2121
8000
Input to Output Test Voltage, Method a*
VIORM x 1.5 = VPR, Type and sample test,
tm = 60 sec, Partial Discharge < 5 pC
VPR
V peak
Highest Allowable Overvoltage*
(Transient Overvoltage, tini = 10 sec)
VIOTM
V peak
Safety Limiting Values
(Maximum values allowed in the event of a failure,
also see Figure 12, Thermal Derating curve.)
Case Temperature
Current (Input Current IF, PS = 0)
Output Power
TS
IS,INPUT
PS,OUTPUT
150
400
700
°C
mA
mW
Insulation Resistance at TS, VIO = 500 V
RS
≥109
Ω
*Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section IEC/EN/DIN EN 60747-5-2, for a
detailed description.
Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in applica-
tion.
9
Absolute Maximum Ratings
Parameter
Symbol
Min.
-55
Max.
125
85
Units
°C
Note
Storage Temperature
Operating Temperature
Average Forward Input Current
TS
T
-40
°C
A
IF(AVG)
10
mA
1
1
Peak Transient Input Current
(≤ 1 µs Pulse Width, 300 pps)
IF(TRAN)
1.0
40
A
(≤ 200 µs Pulse Width,
< 1% Duty Cycle)
HCNW22XX
HCNW22XX
mA
Reverse Input Voltage
VR
IO
5
V
1
1
3
Average Output Current
Supply Voltage
25
mA
V
V
0
20
20
CC
Output Voltage
VO
PT
-0.5
V
1
2
Total Package Power Dissipation
210
mW
HCPL-223X
294
Output Power Dissipation
PO
See Figure 7
1
Lead Solder Temperature (Through Hole Parts Only)
260°C for 10 sec.,
1.6 mm below seating plane
HCNW22XX
260°C for 10 sec., up to seating plane
See Package Outline Drawings section
Solder Reflow Temperature Profile
(Surface Mount Parts Only)
Recommended Operating Conditions
Parameter
Symbol
VCC
Min.
4.5
1.6*
1.8†
-
Max.
20
Units
V
Power Supply Voltage
Forward Input Current (ON)
IF(ON)
5
mA
HCPL-223X
Forward Input Voltage (OFF)
Operating Temperature
Junction Temperature
Fan Out
VF(OFF)
TA
0.8
85
125
4
V
-40
-40
°C
°C
TJ
N
TTL Loads
*The initial switching threshold is 1.6 mA or less. It is recommended that 2.2 mA be used to permit at least a 20% LED degradation guardband.
†The initial switching threshold is 1.8 mA or less. It is recommended that 2.5 mA be used to permit at least a 20% LED degradation guardband.
10
Electrical Specifications
-40°C ≤ TA ≤ 85°C, 4.5 V ≤ VCC ≤ 20 V, 1.6 mA ≤ IF(ON)* ≤ 5 mA, 0 V ≤ VF(OFF) ≤ 0.8 V, unless otherwise specified.
All Typicals at TA = 25°C. See Note 7.
Parameter
Sym.
VOL
Min. Typ. Max. Units
Test ConditionsFig.
IOL = 6.4 mA (4 TTL Loads)
IOH = -2.6 mA
Note
1, 3
Fig
1
Logic Low Output Voltage
0.5
V
V
Logic High Output Voltage
VOH
2.4
2.7
**
2, 3,
1
(VOUT < V )
CC
IOH = -0.4 mA
Output Leakage Current
IOHH
100
500
6.0
µA
VO = 5.5 V
VO = 20 V
IF = 5 mA
1
Logic Low Supply
Current
ICCL
3.7
4.3
7.4
8.6
2.4
2.7
4.8
5.4
mA
VCC = 5.5 V
VCC = 20 V
VCC = 5.5 V
VCC = 20 V
VCC = 5.5 V
VCC = 20 V
VCC = 5.5 V
VCC = 20 V
VO = VCC = 5.5 V
VO = VCC = 20 V
VCC = 5.5 V
VCC = 20 V
TA = 25°C
VF = 0 V
IO = Open
7.0
HCPL-223X
12.0
14.0
4.0
Logic High Supply
Current
ICCH
mA
IF = 5 mA
IO = Open
5.0
HCPL-223X
8.0
10.0
Logic Low Short Circuit
Output Current
IOSL
IOSH
VF
15
20
mA
mA
V
VF = 0 V
1, 3
1, 3
1
VO = GND
IF = 5 mA
Logic High Short Circuit
Output Current
-10
-20
Input Forward Voltage
1.5
1.5
1.7
IF = 5 mA
4
1.85
1.82
1.95
HCNW22XX
TA = 25°C
Input Reverse Breakdown
BVR
5
3
V
IR = 10 µA
1
Voltage
HCNW22XX
IR = 100 µA
Input Diode Temperature
∆VF
∆TA
CIN
-1.7
-1.4
60
mV/°C IF = 5 mA
Coefficient
HCNW22XX
Input Capacitance
HCNW22XX
pF
f = 1 MHz, VF = 0 V
1, 4
70
*For HCPL-223X, 1.8 mA ≤ IF(ON) ≤ 5 mA.
**Typical VOH = VCC - 2.1 V.
11
Switching Specifications (AC)
-40°C ≤ TA ≤ 85°C, 4.5 V ≤ VCC ≤ 20 V, 1.6 mA ≤ IF(ON)* ≤ 5 mA, 0 V ≤ VF(OFF) ≤ 0.8 V.
All Typicals at TA = 25°C, VCC = 5 V, IF(ON) = 3 mA unless otherwise specified.
Parameter
Sym.
Min. Typ. Max. Units
Test Conditions
Without Peaking Capacitor
HCNW22XX
Fig.
Note
Propagation Delay Time
to Logic Low
Output Level
tPHL
150
160
150
110
180
90
ns
5, 6
1, 6
300
300
With Peaking Capacitor
Without Peaking Capacitor
HCNW22XX
Propagation Delay Time
tPLH
ns
5, 6
1, 6
to Logic High
Output Level
With Peaking Capacitor
Output Rise Time (10-90%)
Output Fall Time (90-10%)
tr
tf
30
ns
ns
5, 9
5, 9
1
1
7
Parameter
Sym.
Device
Min.
Units
Test Conditions Fig.
Note
Logic High
Common Mode
Transient
|CMH|
HCPL-2201/02
HCPL-0201
HCPL-2231
HCNW2201
1,000
V/µs
|VCM| = 50 V
IF = 1.6 mA†
VCC = 5 V
TA = 25°C
10
1, 7
Immunity
HCPL-2211/12
HCPL-0211
5,000
10,000
1,000
V/µs
V/µs
V/µs
|VCM| = 300 V
IF = 1.6 mA‡
HCPL-2232
HCNW2211
|VCM| = 1 kV
IF = 5.0 mA
Logic Low
|CML|
HCPL-2201/02
HCPL-0201
HCPL-2231
HCNW2201
|VCM| = 50 V
VF = 0 V
10
1, 7
Common Mode
Transient
VCC = 5 V
TA = 25°C
HCPL-2211/12
HCPL-0211
HCPL-2232
HCNW2211
10,000
V/µs
|VCM| = 1 kV
*For HCPL-223X, 1.8 mA ≤ IF(ON) ≤ 5 mA.
†IF = 1.8 mA for HCPL-2231.
‡IF = 1.8 mA for HCPL-2232.
12
Package Characteristics
Parameter
Sym.
Min. Typ. Max. Units
Test Conditions
Fig.
Note
5, 10
5, 11
Input-Output Momentary
Withstand
VISO
3750
5000
V rms RH < 50%, t = 1 min.
TA = 25°C
HCNW22XX
Voltage*
Input-Output Resistance
RI-O
1012
1013
Ω
VI-O = 500 Vdc
5
HCNW22XX
1012
1011
TA = 25°C
TA = 100°C
Input-Output Capacitance
HCNW22XX
CI-O
0.6
0.5
pF
f = 1 MHz,
5
0.6
TA = 25°C, VI-O = 0 Vdc
Input-Input Insulation
Leakage Current
II-I
0.005
µA
Relative Humidity = 45%,
12
t = 5 s, VI-I = 500 V
Resistance (Input-Input)
Capacitance (Input-Input)
RI-I
CI-I
1011
0.25
Ω
VI-I = 500 V
f = 1 MHz
12
12
pF
*The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage
rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table (if applicable), your equipment level
safety specification or Avago Application Note 1074 entitled “Optocoupler Input-Output Endurance Voltage,” publication number 5963-2203
Notes:
1. Each channel.
2. Derate total package power dissipation, PT, linearly above 70°C free-air temperature at a rate of 4.5 mW/°C.
3. Duration of output short circuit time should not exceed 10 ms.
4. For single devices, input capacitance is measured between pin 2 and pin 3.
5. Device considered a two-terminal device: pins 1, 2, 3, and 4 shorted together and pins 5, 6, 7, and 8 shorted together.
6. The tPLH propagation delay is measured from the 50% point on the leading edge of the input pulse to the 1.3 V point on the leading edge of
the output pulse. The tPHL propagation delay is measured from the 50% point on the trailing edge of the input pulse to the 1.3 V point on the
trailing edge of the output pulse.
7. CMH is the maximum slew rate of the common mode voltage that can be sustained with the output voltage in the logic high state, VO > 2.0 V.
CML is the maximum slew rate of the common mode voltage that can be sustained with the output voltage in the logic low state, VO < 0.8 V.
8. For HCPL-2202/12, VO is on pin 6.
9. Use of a 0.1 µF bypass capacitor connected between pins 5 and 8 is recommended.
10. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥4500 V rms for one second (leakage
detection current limit, II-O ≤5 µA). This test is performed before the 100% production test for partial discharge (Method b) shown in the IEC/
EN/DIN EN 60747-5-2 Insulation Characteristics Table, if applicable.
11. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥6000 V rms for one second (leakage
detection current limit, II-O ≤5 µA). This test is performed before the 100% production test for partial discharge (Method b) shown in the IEC/
EN/DIN EN 60747-5-2 Insulation Characteristics Table.
12. For HCPL-2231/32 only. Measured between pins 1 and 2, shorted together, and pins 3 and 4, shorted together.
13
1.0
0
-1
-2
-3
-4
5
4
3
V
T
= 4.5 V
V
V
= 4.5 V
= 0 V
= 6.4 mA
CC
= 25 °C
V
I
= 4.5 V
CC
F
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
CC
= 5 mA
A
F
I
O
V
= 2.7 V
O
I
= -2.6 mA
O
2
1
0
-5
-6
V
= 2.4 V
O
I
= 6.4 mA
O
-7
-8
0.1
0
-60 -40 -20
0
20 40 60 80 100
-60 -40 -20
0
20 40 60 80 100
0
0.5
I – INPUT CURRENT – mA
F
1.0
1.5
T
– TEMPERATURE – °C
T
– TEMPERATURE – °C
A
A
Figure 1. Typical logic low output voltage vs.
temperature.
Figure 2. Typical logic high output current vs.
temperature.
Figure 3. Typical output voltage vs. forward
input current.
HCPL-22XX
HCPL-02XX
HCNW22XX
1000
1000
T
= 25 °C
T
= 25 °C
A
A
100
10
100
10
I
I
F
F
+
F
+
F
V
V
–
–
1.0
1.0
0.1
0.01
0.1
0.01
0.001
0.001
1.1
1.2
1.3
1.4
1.5
1.1
1.2
1.3
1.4
1.5
1.6
V
– FORWARD VOLTAGE – V
V
– FORWARD VOLTAGE – V
F
F
Figure 4. Typical input diode forward characteristic.
PULSE GEN.
= t 5 ns
f = 100 kHz
10 % DUTY
CYCLE
PULSE GEN.
= t 5 ns
f = 100 kHz
10 % DUTY
CYCLE
V
CC
t
=
f
t
=
f
r
r
OUTPUT V
HCPL-2201/11
HCPL-02XX
HCNW22XX
O
V
CC
MONITORING
NODE
5 V
OUTPUT V
O
V
Z
= 5 V
= 50
O
V
Z
= 5 V
= 50
O
O
O
MONITORING
NODE
V
1
2
3
4
8
7
6
5
CC
5 V
619 Ω
HCPL-223X
V
*
D
1
1
2
3
4
8
7
6
5
CC
INPUT
MONITORING
NODE
619 Ω
INPUT
MONITORING
NODE
D
*
1
D
D
D
2
3
4
C
15 pF
=
2
D
D
D
2
3
4
GND
C =
2
15 pF
5 kΩ
R
1
C
=
1
120 pF
GND
5 kΩ
R
1
C
=
1
120 pF
THE PROBE AND JIG CAPACITANCES
ARE INCLUDED IN C AND
C
.
2
1
THE PROBE AND JIG CAPACITANCES
ARE INCLUDED IN C AND
R
2.15 k� 1.10 k� 681 �
(ON) 1.6 mA 3 mA
5 mA
ALL DIODES ARE 1N916 OR 1N3064.
1
C
.
2
1
I
F
R
1.96 k� 1.10 k� 681 �
(ON) 1.8 mA 3 mA
5 mA
ALL DIODES ARE 1N916 OR 1N3064.
1
I
F
I
(ON)
F
INPUT I
F
50 % I (ON)
F
0 mA
t
t
PHL
PLH
V
OH
1.3 V
OUTPUT V
O
V
OL
Figure 5. Circuit for tPLH, tPHL, tr, tf.
* 0.1 µF BYPASS — SEE NOTE 9.
14
HCPL-22XX
HCPL-02XX
HCNW22XX
= 5.0 V, 20 V
C1 (120 pF) PEAKING CAPACITOR
IS USED. SEE FIGURE 5.
250
80
250
V
V
= 5.0 V, 20 V
CC
CC
C1 (120 pF) PEAKING
CAPACITOR IS USED.
SEE FIGURE 5.
I
(mA)
5
3
F
T
= 75 °C
A
I
(mA)
5
200
150
200
150
60
40
F
*I = 1.8 mA FOR HCPL-223X
T
A
=
F
DEVICES.
80°C
1.6*
3
1.6
1.6*
- 5
t
t
PHL
PHL
T
= 85 °C
A
1.6,
5
100
50
100
50
20
0
t
PLH
t
PLH
-60 -40 -20
0
20 40 60 80 100
-60 -40 -20
0
20 40 60 80 100
0
10
15
20
5
T
– TEMPERATURE – °C
V
CC
– SUPPLY VOLTAGE – V
T
– TEMPERATURE – °C
A
A
Figure 6. Typical propagation delays vs. temperature.
Figure 7. Maximum output power per channel
vs. supply voltage.
100
20
V
= 5 V
CC
TYPICAL
V
vs. V
OH
AT I = -2.6 mA
CC
80
60
40
O
15
10
T
= 25 °C
A
t
t
r
f
5
0
20
0
-60 -40 -20
0
20 40 60 80 100
0
5
10
15
20
T
– TEMPERATURE – °C
V
– SUPPLY VOLTAGE – V
A
CC
Figure 8. Typical logic high output voltage vs.
supply voltage.
Figure 9. Typical rise, fall time vs. temperature.
HCPL-2201/11
HCPL-02XX
HCNW22XX
V
V
R
1
CC
CC
HCPL-2231/32
A
OUTPUT V
MONITORING
NODE
OUTPUT V
O
1
8
7
6
5
1
2
3
4
8
7
6
5
O
A
MONITORING
NODE
B
2
3
4
B
+
–
R
IN
V
FF
0.1 µF
BYPASS
0.1 µF
BYPASS
+
–
V
FF
V
–
V
–
CM
CM
+
+
PULSE GENERATOR
PULSE GENERATOR
V
(PEAK)
CM
|V
|
CM
0 V
SWITCH AT A: I = 1.6 mA**
F
V
OH
V
(MIN.)*
O
OUTPUT V
SWITCH AT B: V = 0 V
O
F
V
(MAX.)*
O
V
OL
* SEE NOTE 7, 9.
** I = 1.8 mA FOR HCPL-2231/32 DEVICES.
F
Figure 10. Test circuit for common mode transient immunity and typical waveforms.
15
HCPL-22XX
HCPL-02XX
HCNW22XX
= 5.0 V
1.0
1.0
V
V
V
V
= 5.0 V
= 20 V
CC
CC
= 20 V
CC
CC
0.9
0.8
0.7
0.9
0.8
0.7
I
I
(ON)
(OFF)
I
I
(ON)
F
F
F
(OFF)
F
I
I
(ON)
F
0.6
0.5
0.6
0.5
I
I
(ON)
(OFF)
F
F
F
(OFF)
-60 -40 -20
0
20 40 60 80 100
-60 -40 -20
0
20 40 60 80 100
T
– TEMPERATURE – °C
T
A
– TEMPERATURE – °C
A
Figure 11. Typical input threshold current vs. temperature.
HCNW22XX
HCPL-2211/2212 OPTION 060
800
1000
P
I
(mW)
P
(mW)
S
S
900
800
700
600
500
400
300
200
700
600
500
400
300
200
100
0
(mA)
I
(mA)
S
S
100
0
0
25
50 75 100 125 150 175
0
25 50 75 100 125 150 175 200
– CASE TEMPERATURE – °C
T
– CASE TEMPERATURE – °C
T
S
S
Figure 12. Thermal derating curve, dependence of safety limiting value with case temperature per IEC/EN/DIN EN 60747-5-2.
HCPL-2201/11
HCPL-02XX
HCNW22XX
V
(+5 V)
CC2
V
(+5 V)
CC1
1
2
3
4
8
7
6
5
1.1 kΩ
DATA OUTPUT
*
DATA INPUT
TTL OR LSTTL
UP TO 16 LSTTL LOADS
OR 4 TTL LOADS
1
* 0.1 µF BYPASS
2
Figure 13a. Recommended LSTTL to LSTTL circuit where 500 ns propagation delay is sufficient.
16
HCPL-2201/11
HCPL-02XX
HCNW22XX
V
(+5 V)
CC2
80 Ω
V
(+5 V)
CC1
1
2
3
4
8
7
6
5
120 pF
1.1 kΩ
DATA OUTPUT
*
DATA INPUT
TTL OR LSTTL
UP TO 16 LSTTL LOADS
OR 4 TTL LOADS
1
* 0.1 µF BYPASS
2
Figure 13b. Recommended LSTTL to LSTTL circuit for applications requiring a maximum allowable propagation delay of 300 ns.
V
CC2
(4.5 TO 20 V)
HCPL-2201/11
HCPL-02XX
HCNW22XX
80 Ω*
R
L
V
(+5 V)
V
CC1
CC
1
2
3
4
8
7
6
5
HCPL-2201/11
HCPL-02XX
HCNW22XX
120 pF*
1.1 kΩ
CMOS
DATA OUTPUT
V
(+5 V)
CC1
**
1.1 kΩ
DATA INPUT
V
CC
1
2
3
4
8
7
6
5
TTL OR LSTTL
GND
DATA
INPUT
D1
TTL or
LSTTL
TOTEM
2
POLE
OUTPUT
GATE
1
V
5 V
10 V
15 V
20 V
R
L
* 120 pF PEAKING CAPACITOR
MAY BE OMITTED AND 80 Ω
RESISTOR MAY BE SHORTED
WHERE 500 ns PROPAGATION
DELAY IS SUFFICIENT.
CC2
GND
1.1 kΩ
2.37 kΩ
3.83 kΩ
5.11 kΩ
D1 (1N4150) REQUIRED FOR
ACTIVE PULL-UP DRIVER.
**0.1 µF BYPASS
Figure 14. LSTTL to CMOS interface circuit.
Figure 15. Alternative LED drive circuit.
HCPL-2201/11
HCPL-02XX
HCNW22XX
80 Ω*
V
(+5 V)
V
CC
CC
1
2
3
4
8
7
6
5
120 pF*
1.1 kΩ
4.7 kΩ
TTL OR LSTTL
DATA INPUT
GND
OPEN
COLLECTOR
GATE
* 120 pF PEAKING CAPACITOR
MAY BE OMITTED AND 80 Ω
RESISTOR MAY BE SHORTED
WHERE 500 ns PROPAGATION
DELAY IS SUFFICIENT.
Figure 16. Series LED drive with open collector gate (4.7 k resistor shunts IOH from the LED).
17
For product information and a complete list of distributors, please go to our website: www.avagotech.com
Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries.
Data subject to change. Copyright © 2005-2010 Avago Technologies. All rights reserved. Obsoletes AV01-0556EN
AV02-0674EN - January 28, 2010
相关型号：
©2020 ICPDF网 联系我们和版权申明